Owner`s manual | Clifford 800 Automobile Alarm User Manual

World-Class Auto Security
TM
intelliguard
800
Owner's Manual
Table of Contents
Standard Features of the IntelliGuard 8OO . . . . . . . . . . . . . . 3
Welcome
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Your 4-button/12-channel remote controls . . . . . . . . . . . . . . 8
How to use your keychain remote control . . . . . . . . . . . . . . . .
8
To transmit channel 1, 2, 3 or 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
To transmit channel 5, 6, 7 or 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
To transmit channel 9, 10, 11 or 12 . . . . . . . . . . . . . . . . . . . . . . . . . 8
What each button/channel does . . . . . . . . . . . . . . . . . . . . .
9
AntiScan™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
UltraSecure™ valet mode . . . . . . . . . . . . . . . . . . . . . . . 11
Your secret valet code . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
To enable valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Keyless entry in valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
To exit valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting your own secret valet code . . . . . . . . . . . . . . . . . . . . 12
How to interpret the chirps and parking light flashes . . . . . . . . 12
Anti-CodeGrabbing™ (ACG) with Random Code Encryption . . . 13
Enhanced AutoArming™ . . . . . . . . . . . . . . . . . . . . . . . . 13
AutoArming enable/disable . . . . . . . . . . . . . . . . . . . . . . . . 13
Visual acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . 13
User-selectable entry delay . . . . . . . . . . . . . . . . . . . . . . . . 13
AutoArm & Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Instant AutoArming bypass . . . . . . . . . . . . . . . . . . . . . . . . . 13
Electronically Programmable Dual-Zone Proximity Sensor . . . . . 14
Remote QuickAccess™ . . . . . . . . . . . . . . . . . . . . . . . . 14
FACT — False Alarm Control and Test
Fault-Proof™ starter interrupt
. . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . 15
1
Table of Contents (cont.)
Optional tamper-proof ignition immobilization
Smart AutoTesting™
. . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . . 16
Specific malfunction identification . . . . . . . . . . . . . . . . . . . . . 16
Automatic malfunction bypass . . . . . . . . . . . . . . . . . . . . 16
How to interpret the LED status indicator . . . . . . . . . . . . . . . 16
Multiple-event TotalRecall™
. . . . . . . . . . . . . . . . . . . . . 17
Smart prior intrusion attempt alert
Headlight Reminder
. . . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . . . . . . . . . . . . . . 17
Smart Trunk Release Capability . . . . . . . . . . . . . . . . . . . . 18
SmartPowerUp™ II
. . . . . . . . . . . . . . . . . . . . . . . . . . . 18
AutoLock/AutoUnLock™ . . . . . . . . . . . . . . . . . . . . . . . . 18
High-output MultiSound Medallion™ Siren . . . . . . . . . . . . . . 18
Personalized Siren Sounds . . . . . . . . . . . . . . . . . . . . . . . . . 18
QuietChirps™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Long-term chirp silencing
. . . . . . . . . . . . . . . . . . . . . . . . . 18
Remote controlled chirp muting . . . . . . . . . . . . . . . . . . . . . . 19
Siren duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
User-selectable features . . . . . . . . . . . . . . . . . . . . . . . . 20
Matrix of user-selectable features . . . . . . . . . . . . . . . . . . . 21–22
EXAMPLE 1: Turn off siren sound number 2 . . . . . . . . . . . . . . . . . . . . 23
EXAMPLE 2: Turn off siren sound numbers 4 and 6, then turn on QuietChirps . 23
Adding new remote controls
. . . . . . . . . . . . . . . . . . . . . 23
How to erase the codes of lost or stolen remote controls . . . . . . 23
All IntelliGuard Series systems are covered by
one or more of the following Clifford Electronics patents:
4,158,874; 4,233,642; 4,327,444; 4,383,242; 4,430,685; 4,845,464;
4,887,064; 4,890,108; 4,922,224; 4,997,053; 5,081,667; 5,146,215;
5,157,375 and other patents
2
Standard Features of the IntelliGuard 8OO
✔ $3,OOO AntiTheft Guarantee — Pays you up to $3,000 if you vehicle is
stolen and not recovered (see the AntiTheft guarantee card for details.)
✔ Limited Lifetime Warranty — The control unit and remote controls are
covered for as long as you own the vehicle (see the warranty card for details).
✔ FACT™ — False Alarm Control and Test — Absolutely, positively
eliminates recurring false alarms (user-selectable).
✔ A Pair of 4-Button/12-Channel Remote Controls — Fingertip command
from 100 feet away (up to 300’ with the optional ElectroLoop Antenna).
✔ AntiScan™ — Blocks digital code scanners from disarming the system.
✔ Proprietary Anti-CodeGrabbing™ (ACG) with Random Code Encryption—
Since the remote control never transmits the same code twice, the random
code encryption makes thieves’ “code-grabbers” completely useless.
✔ Multiple-Car Control — Use your system’s 12-channel remote control to
command IntelliGuard systems on up to eight of your vehicles.
✔ Patented Remote Control Code Learning and MultiRemote™ Recognition
— Add or delete, with a few flicks of a switch, up to four Clifford
Anti-CodeGrabbing remote controls.
✔ Patent-Pending UltraSecure Coded Valet Mode— Ensures that no thief can
turn off your IntelliGuard 800 like they can all other alarm brands.
✔ Remotely Adjustable Dual-Zone Proximity Sensor™ — If someone lurks
near your vehicle, the system will sound a one-second warning tone. But if
a thief reaches into the passenger compartment, the system will instantly
blast the MultiSound Medallion Siren.
✔ Remote Sensor Adjustment — Incredibly easy and accurate sensor
adjustment and testing. Just use the remote control to adjust your sensor
any time, any place, without tools and without even knowing where the
sensor is mounted.
— For the utmost in fine-tuning
accuracy. Gives you remote controlled access to 32 sensitivity levels for the
critical interior zone, and 16 levels for the exterior perimeter zone.
Tonal Confirmations of Sensor Adjustments — As you remotely increase
sensitivity, the confirming chirps rise in pitch. Conversely, as you lower each
zone’s sensitivity, the confirmation chirps become lower and lower in pitch.
Adjust and Test Unobtrusively — No repeated arming and disarming. Your
IntelliGuard 800 lets you set and test sensitivity without activating the alarm!
32-Step Incremental Sensitivity Adjustment
3
Standard Features of the IntelliGuard 8OO (cont.)
✔ Remote QuickAccess™ — Change system settings via your remote control:
— Enable or disable valet mode from 100 feet
away! The parking lights and the system LED confirm valet mode entry and exit.
Remote Override of One or Both Sensing Zones — Whenever you wish, a press
of a button on your remote control will override the Proximity Sensor’s outer
warning zone if you must park in an area with heavy pedestrian traffic.
Another press overrides both zones if you need to leave your pet in the car.
Remote Controlled Valet Mode
✔ QuietChirps™ — Select soft or full volume arm/disarm chirp
confirmations.
✔ Remote Headlight Activation Capability— Lets you remotely turn on your
vehicle’s headlights to illuminate your way to and from your car.
✔ Remote Window and Sunroof Closure Capability— On several models of
BMW, Volkswagen and Jaguar, the IntelliGuard 800’s integrated timer
can remotely close all the power windows and sunroof without the need
for any optional modules.
✔ Built-In Parking Light Flasher — The parking lights will visually confirm
alarm and doorlock status from a distance.
✔ Remote Courtesy Lighting — Automatically turns on your vehicle’s
interior light(s) when you remotely disarm, and keeps them on for 30
seconds or until you start the engine, whichever occurs first.
✔ Smart Trunk Release Capability — An electronic interlock ensures that the
optional remote trunk release can be activated only when the system is
disarmed. To further prevent accidental activation, the interlock also makes
sure that the trunk cannot be remotely opened while the ignition is on.
✔ User-Programmable MultiSound Medallion™ Siren — Designed entirely by
Clifford engineers, this unique siren is superior in performance, features,
reliability and even aesthetics to all other look-alike, sound-alike sirens.
— Up to 64 different siren sound combinations.
— All electronics of the MultiSound Medallion Siren are built
right into the control unit, sheltering the siren electronics from the harsh
underhood environment.
Personalized Siren Sounds™
Ultra-Reliability
User-Selectable 30/60-Second Siren Duration
— Automatically limits siren sounding
to no more than 5 minutes even if a door is left open in the wake of an
intrusion attempt.
Patented Automatic Noise Abatement
4
Standard Features of the IntelliGuard 8OO (cont.)
✔ Headlight Reminder— Warns you if you forget to turn off the headlights
after you park your vehicle.
✔ Dual-Mode Chirp Silencing — Your choice of either long-term chirp
silencing or remote controlled chirp muting whenever you wish.
✔ Extended Range Capability — Add an optional ElectroLoop Antenna to
triple remote control range to as much as 300 feet! Highly recommended
for use with the Clifford IntelliStart remote engine starter accessory.
✔ Remote Controlled Door Locking and Unlocking — A single press of
remote control button 1 simultaneously arms your IntelliGuard 800 and
locks all the doors, another press disarms and unlocks.
— Automatically locks the doors when you begin driving.
— Automatically unlocks the doors for you and your passengers
when you park your vehicle.
Deluxe Remote Keyless Entry in Valet Mode — Allows for remote controlled
door locking/unlocking with visual parking light confirmations and interior
light illumination even while the IntelliGuard 800 is in valet mode.
AutoLock™
AutoUnLock
✔ Patented Smart AutoTesting™ — Automatically tests all system sensors
and triggers, and specifically identifies any malfunction, virtually
eliminating costly trouble-shooting time.
✔ Patented Malfunction AutoBypass™ — Automatically bypasses any trigger
or sensor malfunction, then arms all other points to continue to provide
the utmost possible protection.
✔ Eight-Event TotalRecall™ — Stores the identities of the last eight system
triggers and/or sensors activated. This provides an invaluable
informational and diagnostic means.
✔ Patented Smart Prior Intrusion Attempt Alert — Warns you — from a
distance — if an intrusion attempt was foiled while you were away.
What’s more, the IntelliGuard 800 will specifically identify the sensor or
trigger activated in the intrusion attempt.
✔ Fault-Proof™ Starter Interrupt — Prevent an intruder from cranking the
engine while the system is armed, but allows you to start it even in the
unlikely event of a full system failure.
5
Standard Features of the IntelliGuard 8OO (cont.)
✔ Optional Tamper-Proof Ignition Immobilization — With the addition of an
optional relay, your vehicle’s ignition and fuel system are electronically
disconnected while your IntelliGuard 800 is armed. Even if a thief were
to find and remove the system control unit, he still would not be able to
start the engine.
✔ Enhanced AutoArming™ — Automatically (passively) arms itself if you
forget. Qualifies you for a significant automobile insurance discount (ask
your insurance company).
— Enable or disable the Enhanced AutoArming
features any time you wish.
AutoArm & Lock — Select whether or not the doors will lock when the system
automatically arms itself.
15-Second Entry Delay — If you ever temporarily lose the use of your remote
control, an entry delay will allow you to enter the vehicle and disarm the
system without sounding the siren. For security, the entry delay is only in
effect if the system AutoArms.
Visual Confirmation — The parking lights will flash twice to confirm initiation
of the 30-second AutoArming countdown.
Instant AutoArming Bypass™ — Temporarily and quickly turns off the
AutoArming feature with just a quick turn of the ignition switch.
AutoArming Enable/Disable
✔ Full-Time Remote Panic Feature — Remotely activate the MultiSound
Medallion Siren and flashing parking lights from inside or outside the
vehicle, or even while driving.
✔ High-Luminescence LED Indicator — Adds visual deterrence, confirms
system status, as well as identifying trigger and sensor malfunctions and
activations.
✔ Multiple Trigger/Sensor Inputs — For precise identification of the exact
trigger or sensor tripped in a prior intrusion attempt.
6
C
Welcome to the world of high-technology
vehicle security and convenience
ongratulations on the purchase of your IntelliGuard 800 vehicle
security/convenience system. Clifford Electronics has long been
recognized as the world’s leading manufacturer of high-technology vehicle
security systems and accessories. In fact, Clifford Electronics holds more
patents than all other vehicle security manufacturers combined. Buying
Clifford has always meant buying the best, and nowhere is our
commitment to technological innovation, reliability and quality more
evident than in the astounding IntelliGuard 800.
Your IntelliGuard 800 is loaded with protective features and lifestyle
convenience benefits that other car alarm companies don’t even have on their
wish lists, let alone their alarms. Features like Anti-CodeGrabbing™ that
fights off the latest and most onerous threat from high-tech thieves. A thief
equipped with a code-grabber can record with total impunity the codes of your
car alarm’s remote control from up to several hundred feet away. How? The
thief simply waits for you to arm or disarm your alarm with your remote
control. The thief’s portable, pocket-sized code-grabber will automatically
pick and record the transmitted code off the air. As soon as you walk away,
he simply plays it back, instantly disarming your alarm and unlocking the
doors. It’s like giving the thief your car keys. Code-grabbing will instantly
defeat all other brands of remote controlled car alarms, regardless of
whether they are equipped with anti-scanning or trillions of digital codes.
Clifford’s unique PlainView Coded Valet Switch ensures that no thief,
carjacker or joy-rider can turn off your IntelliGuard 800 like they can with all
other car alarm brands. For total freedom from incorrectly adjusted sensors,
there’s remote controlled adjustment of the system’s dual-zone Proximity
Sensor that allows you to set the desired sensitivity level any place or time
with just a touch of a button on your remote control. Plus there’s remote
controlled valet mode entry/exit, remote controlled sensor override, remote
controlled timed headlight activation, an electronic interlock to prevent
accidental activation of the optional remote trunk release when the system
is armed or when the engine is running, user-programmable MultiSound
Medallion™ Siren with 64 different siren sound combinations to set your
alarm apart from all others, full-time programming access (even while
you’re driving) to dozens of user-selectable features, and much, much more.
Yet despite all the sophistication, the IntelliGuard 800 is amazingly easy to
use: never more difficult than a few flicks of a switch or a press of a
button on one of your miniature keychain remote controls.
7
Your 4-button/12-channel remote controls
The 4-button/12-channel remote control is an ultra-sophisticated miniature radio transmitter powered by a tiny 12-volt battery. Range is up to 100 feet (up to 300 feet with the
optional ElectroLoop Antenna). Obstructions, electrical interference, weather conditions
or a weak battery will reduce range. Your 4-button/12-channel remote control is the key
to your IntelliGuard 800. It incorporates Clifford’s proprietary Anti-CodeGrabbing™
(ACG) technology with Random Code Generation for the ultimate in protection against
“code-grabbing” devices (see page 13). You will use your remote control to arm and
disarm the system, lock and unlock the doors, activate the panic feature, adjust sensor
sensitivity, activate the headlights, control Remote QuickAccess features or command
options such as a remote trunk release, remote memory seat adjustment and even remote
starting of the engine and heater or air conditioner, among other available options.
How to use your keychain
remote control
Your remote control can
individually command up to
12 different system functions
and options. It’s like having
a TV with 12 channels. You
change channels (functions)
with your keychain remote
control. But instead of
putting 12 buttons on the
remote control, we made it
easy: First, the button you
use the most — button 1 to arm, disarm, lock and unlock the doors — is larger than the
others. Buttons 2, 3 and 4 are the smaller buttons to the right, below and left of button 1.
The LevelShift button on the side lets you select channels 5–12:
Just press either button 1, 2, 3 or 4. For instance,
to transmit channel 3, press button 3. While you transmit, the LED indicator will
blink once every second: this indicates level 1.
To transmit either channel 5, 6, 7 or 8: Press the LevelShift button once. This shifts
buttons 1–4 to level 2 (channels 5–8). Then press the desired button within the
next 7 seconds. For instance, to transmit channel 5, press the LevelShift button
once, then press button 1. While you transmit, you’ll notice that the LED indicator
blinks twice, pauses, blinks twice, etc.: this indicates level 2.
To transmit channel 9, 10, 11 or 12: Press the LevelShift button twice. This shifts
buttons 1–4 to level 3 (channels 9–12). Then press the corresponding button within
the next 7 seconds. For instance, to transmit channel 10, press the LevelShift button
twice, then press button 2. While you transmit, you’ll notice that the LED blinks
three times, pauses, blinks three times, etc.: this indicates level 3.
To transmit either channel 1, 2, 3 or 4:
NOTE: One second after you stop transmitting level 2 or level 3 (channels 5–12),
the remote control automatically returns to level 1 (channels 1–4).
8
What each button/channel does
Your IntelliGuard 800 remote controls come pre-programmed so that certain channels
command certain functions. If you wish, you can actually assign any channel (except 9
through 12) to any function (see pages 20–22). The following chart indicates what each
remote control channel number does, and how to transmit each channel number.
Factory settings of the 12 remote control channels
Transmitting
channel
number:
Causes the system to:
Press the How Press
LevelShift many button
button? times? number
1
arm or disarm and lock or unlock the doors
no
—
1
2
pop the trunk* (if the system is disarmed)
AND
turn on the headlights* (if the system is armed)
no
—
2
3
silently arm or disarm
no
—
3
4
activate optional accessory function #1
no
—
4
5
activate optional accessory function #2
yes
once
1
6
activate optional accessory function #3
yes
once
2
7
activate optional accessory function #4
yes
once
3
8
activate optional accessory function #5
yes
once
4
9
remotely enter or exit valet mode (see page 14)
yes
twice
1
10
turn off one or both sensor zones (see page 14)
yes
twice
2
11
remotely adjust and test sensitivity of the Proximity Sensor’s
passenger compartment zone (see page 14)
yes
twice
3
12
remotely adjust and test sensitivity of the Proximity Sensor’s
exterior warning zone (see page 14)
yes
twice
4
* May require additional wiring.
TO ARM
THE SYSTEM . . . . . . .
Press button 1 (channel 1) once. You will hear two chirps and the
parking lights will flash twice. The dashboard LED will flash
repeatedly and the car doors will automatically lock.
TO DISARM
THE SYSTEM . . . . . . .
Press button 1 (channel 1) again. One chirp and one flash of the
parking lights will confirm disarming. In addition, the car doors
will automatically unlock and the interior lights will turn on and
stay on for 30 seconds or until you start the engine, whichever
occurs first.
TO ACTIVATE
THE PANIC
FEATURE . . . . . . . . . .
Press button 1 for 3 seconds. The lights will flash repeatedly and
the MultiSound Medallion Siren will blare for 30 or 60 seconds
(user-selectable), or until you press button I again to turn it off.
9
TO SILENTLY
ARM OR DISARM
THE SYSTEM . . . . . . .
Press button 3 (channel 3). Your IntelliGuard 800 system will
arm or disarm with all the indications noted on the previous page
except for the chirp acknowledgments.
TO REMOTELY
TURN ON THE
HEADLIGHTS
(OR OTHER
TIMED OPTION) . . . .
Button 2 (channel 2) controls an electronic interlock that allows
you to separately command two different options with the same
channel: one when the system is armed and another when it is
disarmed. Pressing remote control button 2 while the alarm is
armed will activate the system’s built-in timer circuit. This output
is primarily used to optionally activate the headlights for any
duration of your choosing between 1 second and 2.5 minutes (the
timer is factory preset to 30 seconds; see User-selectable features
on pages 20–22).
TO REMOTELY
OPEN THE TRUNK . . .
As noted above, button 2 (channel 2) can control yet another
function when the system is disarmed. Usually, this is an optional
remote trunk release. Thus, pressing button 2 while the alarm is
disarmed will remotely open the trunk (NOTE: to ensure against
accidental activation of the trunk release while driving, the
electronic interlock will prevent remote activation of the trunk
release while the ignition is on).
TO ACTIVATE
Button 4 (channel 4) and channels 5–8 (see How to use your
OTHER OPTIONS
keychain remote control on page 8) can activate other accessories
REGARDLESS OF
such as the Clifford Electronics IntelliStart™ remote engine
ALARM STATE . . . . . . . starter, remote memory seat activation, SmartWindows II remote
power window/sunroof roll-down and venting, a Programmable
Receiver that lets you command your electric garage door/gate
opener(s), etc.
Channels 9 through 12 control your IntelliGuard 800’s Remote
What about
channels 9 – 12?. . . . QuickAccess™ features: remote valet mode entry/exit, remote
override of the exterior warning zone of the Proximity Sensor,
remote override of both Proximity Sensor zones, and remote
adjustment of each of the two zones. See Remote QuickAccess
features on page 14 for details.
AntiScan™
Thieves can disarm some other brands of car alarms with a “scanner” than rapidly
transmits one remote control code after another. Clifford’s AntiScan will detect any
scanner and block the codes it generates.
10
UltraSecure™ Coded Valet Mode
Your secret valet code
Within seconds, thieves can disable all other alarm brands by hot-wiring the ignition and
flicking an easy to find “hidden” valet switch. Your IntelliGuard 800 has safeguards that
absolutely ensure that a thief cannot enable the valet mode as a way of “turning off” your
system. How? To enable valet mode, the driver must first enter a secret valet code on the
PlainView switch. Your code will be a 1-to-3-digit number of your choosing. Each digit can
be any number from 1 to 9, (i.e. the code can be any number between 1 and 999, except
those that contain a zero).
Whenever the system is put in valet mode, all of the system’s security features are switched
off. At various times, you will need to switch the system off. For instance, when having your
car serviced, washed or parked by a valet.
NOTE: If you temporarily lose the use of your remote controls, you can disarm
the system by enabling valet mode.
Definitions
Digit: A digit is defined as any number from 1 to 9, inclusive.
Valet code: A valet code may be 1 to 3 digits:
A one-digit code=X=any number between 1-9
A two-digit code=XY=any number between 11-99 (excluding numbers with zeros)
A three-digit code=XYZ=any number between 111-999 (excluding numbers with zeros)
Remember, no code can have a zero.
A rocker switch mounted on the dashboard or console. The switch
has three positions: 1.) Latched 2.) Center 3.) Spring-loaded momentary. When
you press the latched side, the switch remains in its pressed position. When you
press the momentary side, the switch bounces back to the center position.
Entering a digit: To enter a digit, you tap (press and release) on the momentary side
of the PlainView switch the number of times corresponding to the numeral of the
digit to be entered, followed by pressing to the latched side, then returning the
switch to its center position.
Entering a code: If your code has only one digit, enter the code as described in
“Entering a digit,” then return the switch to its center position. If your code has
more than one digit, just repeat the above for each digit of your code, then return
the switch to its center position.
PlainView switch:
Currently, your factory-set valet code is the single digit “2.”
11
To enable valet mode
1. Turn the ignition switch to its “ON” position or start the engine.
2. Enter your secret valet code on the PlainView switch, then return the switch to its
center position.
3. You now have 3 seconds to press the latched position (valet mode). Once you have
entered valet mode, the system’s LED will glow continually for on-going visual
confirmation of valet mode.
Keyless entry in valet mode: Even if valet mode is enabled, you can still remotely
control the convenience features. For instance, simply press button 1 (channel 1)
as if you were disarming. The doors will unlock (as indicated by one flash of the
parking lights) and the interior lights will illuminate. Press button 1 (channel 1)
again and the doors will lock (as indicated by two flashes of the parking lights).
You can also use the remote control’s other channels to activate options such as a
remote trunk release or remote engine starting.
To exit valet mode
1. Turn the ignition switch to its “ON” position or start the engine.
2. Flick the switch back to its center position. The LED will turn off to confirm that the
system is now in its normal operating mode.
NOTE: You can even enable or exit valet mode with your remote control from
outside the vehicle! See the Remote QuickAccess section on page 14.
Setting your own secret valet code
Since all IntelliGuard systems have the same factory-set code, it is highly advisable that
you set your own valet code. You may choose any 1-, 2-, or 3-digit code that does not
have any zeros. You can also change your valet code whenever you want. Simply write
down the 1-to-3 digit code you wish to use (remember, no zeros in the code), then refer
to the User-selectable features section on pages 20-22.
How to interpret the chirps and parking light flashes
When you use the remote control, the system responds with chirps (unless the chirp
muting feature is turned on) and parking light flashes. These chirp/flash
acknowledgments mean:
Chirps and flashes
Meaning
1
Your IntelliGuard system is disarmed
2
Your IntelliGuard system is armed
2 and then 4
Armed but there is a door open (if there was a 5-sec. delay) or the sensor is
malfunctioning (if there was a 10-sec. delay) (see Smart AutoTesting on page 16)
3
Disarmed but there was an intrusion attempt while you were away
(see Smart Prior Intrusion Attempt on page 17)
4
Armed but the hood or trunk is ajar (see Smart AutoTesting on page 16)
12
Anti-CodeGrabbing™ (ACG) with Random Code Encryption
A Clifford exclusive that protects you and your automobile from the most effective and
onerous car stealing device ever used by car thieves — a code-grabber. Code-grabbers
are far more effective and efficient than scanning (see above). Unlike scanners that
sequentially transmit one digital code after another hoping one of them is the correct
code to disarm the alarm (a process that may take hours, days or even years depending
on the alarm’s number of codes), code-grabbers literally record, from hundreds of feet
away, the code sent by your car alarm remote control. A code-grabber will instantly
duplicate any remote control code, even if the remote has billions or trillions of codes.
The thief simply waits for you to arm your alarm with the remote control and walk
away. Then he plays back the code, instantly disarming your car’s alarm and unlocking
the doors. It’s like giving the thief your keys. All non-Clifford alarms can be defeated
that easily. In contrast, IntelliGuard systems use complex digital signal processing and
unbreachable encryption to randomly change the digital code every time you use the
remote. Your remote will never transmit the same code. Thus the code recorded and
played back by the thief’s code-grabber will never be accepted by your IntelliGuard 800.
Only ACG can make a car alarm impervious to code-grabbing, and only Clifford
systems have ACG with Random Code Encryption.
Enhanced AutoArming™
If this feature is enabled and you forget to remotely arm your IntelliGuard 800, the
system will arm itself automatically (“passively”) 30 seconds after the vehicle doors are
closed. For your convenience, if you re-open any door(s) within the 30-second
countdown, AutoArming will restart from the beginning once all doors are closed. Your
IntelliGuard 800 includes all these additional Enhanced AutoArming features:
AutoArming enable/disable: If you prefer, you may deactivate or reactivate the
AutoArming feature. See User-selectable features on pages 20–22.
Visual acknowledgment: Five seconds after you exit the vehicle and close all
the doors, the parking lights will flash twice to confirm that the AutoArming
countdown is progressing. Then, 25 seconds later, the system will AutoArm.
User-selectable entry delay: If you temporarily lose the use of your remote
controls, you may turn on the 15-second entry delay feature. This allows you
to silently disarm the system by starting the engine within 15 seconds of
opening the door. See User-selectable features on pages 20–22.
AutoArm & Lock: To ensure you can’t accidentally lock your keys inside the
car, the system is factory-set not to lock the doors upon AutoArming. To
change this setting, see User-selectable features on pages 20–22.
Instant AutoArming bypass: Prevents AutoArming when fueling the vehicle
and other times when you wish to temporarily bypass AutoArming. To
activate Instant AutoArming Bypass, rapidly turn the ignition switch to “ON”
then “OFF.” You will hear a single siren chirp to confirm that the system will
not AutoArm. The system reverts to its normal operating mode when you next
start the engine.
13
Electronically Programmable Dual-Zone Proximity Sensor™
Your IntelliGuard 800’s Dual-Zone Proximity Sensor has both an outer and an interior
zone. The outer “warning” zone can detect potential vandals and thieves lurking near
your vehicle before they even have a chance to touch your automobile. Anyone lingering
too near your vehicle will bee warned away with a distinctive one-second warning tone.
But if a thief actually reaches into your vehicle’s passenger compartment, the system
will sound its full siren blast for 30 or 60 seconds (whichever you select, see
User-selectable features on page 20–22). What’s more, you can adjust the sensitivity of
each of the two sensor zones via your remote control. Use the Remote QuickAccess
method noted on below or see User-selectable features on pages 20–22. For an even greater
level of security, consider Clifford Electronics optional sensors: IntelliSensor 3-D™ (a
digital analysis glass tampering sensor) and the OmniSensor™ (a digital analysis
vibration/impact sensor).
Remote QuickAccess™
For the greatest ease of use, the Remote QuickAccess features permit you a quick and
easy way of controlling, with just the remote, the most commonly used features, namely:
The valet mode, Proximity Sensor zone override, and sensor adjustment. Now you can
control these features any time you wish from outside your vehicle with just your remote
control. Here’s how:
QuickAccess Valet Mode: To enter valet mode remotely, transmit channel 9
(press the LevelShift button on the side of the remote control twice, then press
button 1). The parking lights will flash twice and the LED in the vehicle will
stay on to indicate the system is in valet mode. To exit valet mode remotely,
transmit channel 9 again and the system will confirm exit of valet mode with
one flash of the parking lights and the LED will turn off. (NOTE: If you enter
valet mode via the remote control, you must exit valet mode in the same
manner. If you use the PlainView switch to enter valet mode, you must use
the switch to exit valet mode.)
QuickAccess Proximity Sensor Zone Override: Transmitting channel 10 (press the
LevelShift button on the side of the remote control twice, then press button 2)
immediately after arming the system with channel 1 will override the exterior
warning zone of the Proximity Sensor (confirmed by 4 parking light flashes).
Transmitting channel 10 again will turn off both zones of the sensor for those
times when you must leave your pet or a passenger in the vehicle. Keep in
mind that you must transmit channel 10 within ten seconds of remote arming.
QuickAccess Testing & Adjustment of the Proximity Sensor Zones: Due to
ever-changing conditions, all alarms require periodic fine-tuning of their
sensors. In fact, an improperly adjusted sensor is the most common cause of
false alarms. With other alarms, this requires repeated trips back to the dealer.
Not so with your IntelliGuard 800. You can adjust sensitivity electronically
without tools and without even knowing where the sensor is mounted! If you
find the current setting(s) of the Proximity Sensor to be either too sensitive or
14
not sensitive enough, you may individually test and adjust the sensitivity
settings yourself. To do so, just use the following procedure:
1. Disarm the system, open the driver’s window, then select the zone you wish:
a. Interior zone: Transmit channel 11 (LevelShift twice, then button 3).
b.Outer warning zone: Transmit channel 12 (LevelShift twice, then button 4).
2. To test the current sensitivity setting:
a. Interior zone: Lean into the passenger compartment. You will hear a chirp
when the zone detects your presence. Ideally, it should chirp when you lean
over the driver’s seat, but remain silent when you lean toward the window.
b.Outer zone: Lean toward the driver’s window. You will hear a chirp when
the zone detects your presence. Ideally, it should chirp only when you are
within about one foot of the vehicle.
3. To increase sensitivity, press button 2 on your remote control. To decrease it,
press button 4. Each time you increase sensitivity, the siren will chirp in higher
and higher pitched tones to confirm the higher sensitivity. Conversely, lower
and lower tones confirm each sensitivity decrease. Two normal tone chirps
indicate minimum and maximum sensitivity. There are 32 sensitivity levels for
the Proximity Sensor’s critical inner zone; 16 for the outer warning zone.
4. Repeat steps 2 and 3 until you are satisfied with the sensitivity, then press
button 1 to record the new sensitivity setting and exit the sensor test/adjust
mode (you’ll hear three chirps to confirm exit). You may now either repeat
steps 1–4 for the other sensor zone, or press button 1 to arm the system.
Sound complicated? It really isn’t, there’s just a lot of explanation of what’s happening
with each step. All you really have to do is the actions noted in bold type. Give it a try.
FACT™— False Alarm Control and Test
With FACT, you’ll never experience repeated false alarms. If the siren goes off, DO
NOT disarm the system; let it run for the full siren duration. Before sounding the siren a
second time, the system automatically checks for another activated trigger to verify that
an intrusion is in progress. Should the siren sound again, you will know for sure
someone is tampering with your vehicle.
Fault-Proof™ starter interrupt
While the system is armed, the vehicle’s starter circuit is electronically disconnected.
Our Fault-Proof design ensures that you’ll be able to start the engine even in the unlikely
event of a system malfunction. Other, non-Clifford alarms may leave you stranded.
Optional tamper-proof ignition immobilization
If your IntelliGuard 800 is equipped with the ignition immobilization option, while
armed, the system ensures that your vehicle is completely immobilized by automatically
locking out the ignition system. That means that a thief won’t be able to start your
vehicle’s engine even if he had a duplicate of your car key. What’s more, even if he
were to find the system control unit and tear it out of your vehicle, he still won’t be able
to start your car’s engine! That’s Clifford security you can count on.
15
Smart AutoTesting™
Each time you remotely arm the system, it tests all triggers and sensors. If the hood or
trunk is open when you remotely arm, the system will immediately alert you of the
problem by issuing 4 chirps and 4 parking light flashes instead of the usual 2 and 2. If a
door is ajar, you will receive the usual 2 chirps and flashes, then, 5 seconds later, there
will be 4 chirps and 4 flashes. (This door ajar warning will not work on vehicles that
have factory-delayed courtesy lights). If a sensor is malfunctioning, you will receive the
usual 2 chirps and 2 flashes, then, 10 seconds later, there will be 4 chirps and 4 flashes.
NOTE: Since this is a warning indication, you will hear the 4 chirps even if you
have the chirp muting feature turned on.
The system can also indicate the specific
trigger or sensor that is malfunctioning. If you receive the 4-chirp/4-flash
signal upon remote arming, perform the following to identify the
malfunctioning trigger or sensor:
1. Remotely disarm, then turn on the ignition. The LED status indicator inside your
vehicle will be flashing, pause, then repeat.
2. Count the number of blinks in one cycle between pauses (for your convenience, the
blink cycle repeats a total of 5 times) and refer to the chart below:
Specific malfunction identification:
Number of LED blinks between pauses
Malfunction
1 blink
Proximity Sensor
2 blinks
Optional sensor
3 blinks*
Door trigger*
4 blinks
Trunk trigger
5 blinks
Hood trigger
* If your vehicle has a factory-installed feature that turns off or dims the interior courtesy lights
several seconds after you exit the vehicle, the system cannot provide this indication.
Automatic malfunction bypass
To provide the utmost protection even if a system component malfunctions, your
IntelliGuard 800 will automatically bypass any faulty point and arm all other triggers and
sensors until you can have the system serviced by your local Authorized Dealer.
How to interpret the LED status indicator
The LED on your car’s dashboard or console will inform you of the system status:
LED Condition
Meaning
Off
System is disarmed and in normal operating mode (i.e., valet mode is off)
On
Valet mode is on, the vehicle can be driven or serviced without having to disarm
Flashing (ignition off)
System is armed and protecting your vehicle
Pause between flashes
Either a malfunction (see above) or an intrusion was attempted (see page 17)
16
Multiple-event TotalRecall™
The system’s non-volatile memory records the identity of the last eight activated or
malfunctioning triggers and/or sensors, which allows your installer to instantly track down
malfunctions and save you substantial servicing costs. To identify the triggers and/or sensors
held in the system’s non-volatile memory, simply perform the following procedure:
1. With the ignition OFF, flick the PlainView valet switch to its latched side.
2. Press button I to “arm” the system, then again to “disarm.”
3. The LED will blink 1–5 times to indicate the most recently activated trigger or
sensor, pause, then blink 1–5 times to indicate the next most recently activated trigger
or sensor, and so on for the last 8 activations.
4. Write down the number of blinks between pauses and refer to the chart below:
Number of LED blinks per cycle
Trigger/sensor that was activated or malfunctioned
1 blink
Proximity Sensor
2 blinks
Optional sensor
3 blinks
Door trigger
4 blinks
Trunk trigger
5 blinks
Hood trigger
Smart prior intrusion attempt alert
When you remotely disarm, if you hear three chirps and see three parking light flashes
(instead of the usual one and one) it means that a trigger or sensor was activated in your
absence. When you enter the vehicle and turn on the ignition (or start the engine), the
LED will blink 1–5 times, pause, then repeat the blink cycle 4 more times. Count the
number of blinks in one cycle and refer to the chart below:
Number of LED blinks per cycle
Trigger/sensor that detected the intrusion attempt
1 blink
Proximity Sensor
2 blinks
Optional sensor
3 blinks
Door trigger
4 blinks
Trunk trigger
5 blinks
Hood trigger
Headlight Reminder
If you turn the ignition off and open the driver’s door to exit the car without having turned
off the headlights, you will be reminded to turn them off with a distinctive warning tone. If
your vehicle already has a similar warning feature, you may turn off your IntelliGuard 800’s
Headlight Reminder feature. See the User-selectable features section on pages 20–22.
17
Smart Trunk Release Capability
Your IntelliGuard 800 has a built-in electronic interlock that automatically prevents
accidental activation of the remote trunk release option. If you have this option, you’ll note
that the system must be disarmed and the ignition must be off in order for you to remotely
pop the trunk with button 2 (channel 2). Transmitting channel 2 while the system is armed
will optionally activate the headlights for any duration of your choosing between 1 second
and 2.5 minutes (factory preset to 30 seconds).
SmartPowerUp™ II
If power to the system control unit is ever removed, SmartPowerUp II ensures that the
system will automatically restore itself to its previous status when power is restored. So
if a thief tampers with the vehicle battery in an attempt to steal your car, the system will
automatically re-arm itself and immediately sound the siren. However, if your vehicle is
to be serviced by a mechanic, just put the system in valet mode. If the mechanic needs to
interrupt vehicle power, your system will automatically return to its valet mode state
when power is restored; there will be no alarm activation and no need to provide your
mechanic with your remote control and instructions on how to use it.
AutoLock/AutoUnLock™
For your safety and that of your passengers, the system automatically locks the doors when
you begin driving, and unlocks them when you turn off the ignition. If you prefer, you
may turn off this feature. See the User-selectable features section on pages 20–22.
High-output MultiSound Medallion™ Siren
All the electronics for the siren are built into the IntelliGuard 800’s control unit rather
than the siren itself. This protects the circuitry from engine heat, dirt and exposure to the
elements (in contrast, the electronics of other alarm companies’ sirens are part of the
siren itself and, therefore, far more susceptible to failure). In addition to greatly enhancing
long-term reliability, your IntelliGuard 800 also provides these additional features:
Personalized Siren Sounds: Most alarm sirens have a single “warble” tone. A
few offer “six-tone” sirens that either cannot be adjusted or require the
physical destruction of certain circuit wires in order to change the sounds (the
change is permanent and cannot be changed again). Your IntelliGuard 800
MultiSound Medallion Siren circuitry is different. As shipped from the
factory, the siren sounds six different alarm sound patterns. However, you
may turn any of the six different alarm sound patterns on or off to create a
different combination of sound patterns. In all, there are 64 different
combinations you may select. You may set your own Personalized Siren
Sounds so if you hear a siren at a distance, you will know for sure whether it is
your car or someone else’s. See User-selectable features on pages 20–22.
QuietChirps™: You can control the volume of the normal arm and disarm
chirps. As shipped from the factory, your system issues full-volume chirp
acknowledgments. If you prefer, you may reduce the chirp volume to a level
18
that is clearly audible, yet less obtrusive. See the User-selectable features
section on pages 20–22.
Long-term chirp silencing: Whenever you wish, you may silence your
IntelliGuard 800’s arm and disarm chirps until you decide to restore them.
The parking light flashes will continue to provide visual confirmation of
remote controlled arming and disarming. See User-selectable features on
pages 20–22.
Remote controlled chirp muting: Remote controlled chirp muting capabilities
are especially valuable when parking late at night in a quiet residential area or
any other time when you want to arm or disarm silently. To arm or disarm
silently, simply press button 3 (channel 3) on your remote control instead of the
usual button 1 (channel 1).
Siren duration: When the system detects an intrusion attempt, the alarm is set
to sound for 30 seconds. However, if you prefer, you may change it to 60
seconds. See the User-selectable features section on pages 20–22.
19
User-selectable features
Your IntelliGuard 800 allows you to set many of its features to your own personal
preferences. Although the system’s programming capabilities are very extensive, we
have made the programming procedures very simple: to make a change, you just flick
the PlainView switch a few times. Once you’ve changed a few settings, you’ll find that
programming IntelliGuard 800 is so easy, you can even do it while driving! The system
comes with all of its features pre-programmed as noted by the bold type in the Matrix of
user-selectable features on the following page. To change any of the settings, use the
steps noted below. To restore the feature to its factory setting, just repeat the procedure:
1. Refer to the Matrix of user-selectable features and make note of the column number
and row number of the feature(s) you wish to program.
2. Insert your ignition key and turn it to the “ON” position, or start the engine (skip this
step if the engine is already running).
3. Enter your disarming code, then press and hold the PlainView switch to its
spring-loaded momentary side for about 3 seconds until you hear a siren chirp.
You’ll also notice that the system LED turns on to indicate that the system is in its
programming mode. The system is now in the “Feature Select” position: the top left
cell of the matrix. From this position, you will first select the feature column (from
left to right), then the feature row (from top to bottom).
4. Select the feature column: To select the column you wish, toggle the switch in and
out of the latched position the same number of times as the column number of the
selected feature (NOTE: each latched-to-center motion is counted as one). After a
one-second pause, you will hear the same number of chirps as the column number
you have selected, audibly confirming your selection.
5. Select the feature row: To select the feature’s row, immediately tap and release the
momentary side of the switch the same number of times as the feature’s row number.
You will hear a single chirp confirmation each time you press the momentary side to
help you count.
a. VERY IMPORTANT: If there is a NOTE number listed in the selected feature of
the matrix, perform the actions listed for that note. Once you have completed the
NOTE instructions, skip step 6 below and go to step 7.
6. After a one-second pause you will hear either one chirp to indicate that the feature
you selected is now turned off, or two chirps to indicate that the feature is now on (on
the siren duration feature, one chirp = 30 seconds, two = 60 seconds).
7. You have now completed the programming of the desired featured. You may select
another feature, or you may exit program mode:
a. To program another feature in that same column, you must repeat step 5 within the
next 3 seconds (if longer than 3 seconds, you will hear three chirps to indicate that
you are now in the “Feature Select” position).
b. To select a different feature column, go to step 4.
c. To exit program mode, turn the ignition off (you’ll hear 3 chirps and the LED will
turn off to indicate exit of program mode). If driving, just wait for 30 seconds and
the system will automatically exit programming mode by itself (indicated by 3
chirps and extinguishing of the LED).
The above may sound complicated, but it really isn’t. Briefly, here is all you do: Choose
the feature you want, enter program mode, select the feature’s column and row, then turn
off the ignition. That’s it! Try the examples on page 23 to see just how easy it really is.
20
Matrix of user-selectable features
Feature Select
Column 1
1st latched
Column 2
2nd latched
Column 3
3rd latched
Column 4
4th latched
Column 5
5th latched
Row 1
1st momentary
Sound 1: on/off
info on page 18
Add new remote to channel 1
info on page 8–9 NOTE 1
Test/adjust primary (normal) zone
of the Proximity Sensor
info on page 14 NOTE 7
QuietChirps: on/off
info on page 18
Headlight Reminder: on/off
info on page 17
Row 2
2nd momentary
Sound 2: on/off
info on page 18
Add new remote to channel 2
info on page 8–9 NOTE 2
Test/adjust secondary (high) zone
of the Proximity Sensor
info on page 14 NOTE 8
Long-term
chirp silencing: on/off
info on page 18
Row 3
3rd momentary
Sound 3: on/off
info on page 18
Add new remote to channel 3
info on page 8–9 NOTE 3
Pulsed/constant
ground output upon panic
15-second entry delay: on/off
info on page 13
Channel 4 output:
pulsed, timed, latched
Row 4
4th momentary
Sound 4: on/off
info on page 18
Add new remote to channel 4
info on page 8–9 NOTE 4
FACT: on/off
info on page 15
AutoLock/UnLock: on/off
info on page 18
Channel 5 output:
pulsed, timed, latched
Row 5
5th momentary
Sound 5: on/off
info on page 18
Add new remote to channel 5
info on page 8–9 NOTE 5
Factory-delayed
courtesy lights: on/off
Enhanced AutoArming: on/off
info on page 13
Siren duration: 30/60 seconds
info on page 18
Row 6
6th momentary
Sound 6: on/off
info on page 18
Erase all channels
info on page 8–9 NOTE 6
Set a new secret valet code
info on page 12 NOTE 9
AutoArm & Lock: on/off
info on page 13
NOT USED
✱
Channel 2 headlight timer:
1sec–2.5min (30sec)
info on page 10 NOTE 10
Gray cells indicate features that require programming by trained Clifford installers. DO NOT change any of these settings.
✱ WARNING: If you have remote window and sunroof closure, DO NOT CHANGE THIS SETTING: it requires installer-only adjustment. Changing the duration may cause damage.
NOTE 1: Transmit channel 1 (or other channel of your choosing) of the new remote
control. You will hear two chirps to indicate that the code has been accepted and
recorded.
NOTE 2: Transmit channel 2 (or other channel of your choosing) of the new remote
control. You will hear two chirps to indicate that the code has been accepted and
recorded.
NOTE 3: Transmit channel 3 (or other channel of your choosing) of the new remote
control. You will hear two chirps to indicate that the code has been accepted and
recorded.
NOTE 4: Transmit channel 4 (or other channel of your choosing) of the new remote
control. You will hear two chirps to indicate that the code has been accepted and
recorded.
NOTE 5: Transmit channel 5 (or other channel of your choosing) of the new remote
control. You will hear two chirps to indicate that the code has been accepted and
recorded.
NOTE 6: When you hear the two chirps, all remote control codes will have been erased
from system memory. You must now add the new and/or existing remote controls to
the system (i.e., program channels 1–5 of each remote that will be used with your
IntelliGuard 800 system).
21
NOTE 7: Turn off the ignition, leave the driver’s window open and exit the vehicle. To
test the current sensitivity, lean into the passenger compartment through the window.
When the sensor detects the intrusion, the system will sound a single confirmation
chirp. To increase the sensitivity setting, press button 2 (you’ll hear higher and higher
confirmation chirps). To decrease sensitivity, press button 4 (you’ll hear lower and
lower chirps). Retest by leaning through the window. When satisfied with the
sensitivity setting, press button 1 to record the new sensitivity level and exit sensor
test/adjust mode (you’ll hear 3 chirps to confirm this). You may now either arm the
system with channel 1 or enter the vehicle.
NOTE 8: Use the same procedure as NOTE 7, but adjust the sensor to detect your
presence when you lean within a foot of the driver’s window.
NOTE 9: Immediately flip the switch to its latched position, then enter the new code
that you wish to use. Make sure to return the switch to its center position when
complete, then wait 3 seconds (you will hear two chirps when the system has accepted
the new code). Turn the ignition off. VERY IMPORTANT: You must immediately
test your new secret disarming/valet code: Turn the ignition on, enter your new code,
then flip the switch to its latched position. The LED will illuminate. If it does not, the
new code you programmed and the one you just entered do not match. The system has
reverted to the previous code.
NOTE 10: The timer starts as soon as you enable this feature (5 latches, 2
momentaries). When the duration you wish has been reached, press button 1 on the
remote control. You will hear two chirps to confirm the new duration. Channel 4
and/or 5 will have this same duration if one or both of these were set by your installer
to operate as a timed output.
22
EXAMPLE 1: Turn off siren sound number 2:
1. Look for the siren’s sound number 2 location on the Matrix.
2. The location is at the intersection of column 1 and row 2. Note the column and row
numbers.
3. With the ignition on, enter you disarming code on the PlainView valet switch, then hold
the switch in its momentary position until you hear a chirp and see the LED turn on.
4. Select feature column 1 by pressing the switch to its latched position, then back to
center. After a brief pause, you’ll hear 1 chirp to indicate column 1.
5. Press and release the momentary side twice. You’ll hear a total of two chirps to
indicate that you selected the feature in row 2 of that column.
6. After a brief pause, you’ll hear a single chirp to indicate that sound #2 is now off.
7. Turn the ignition off (you’ll hear 3 chirps) and you’re done!
If you wish to turn siren sound 2 back on, simply repeat steps 1–7.
EXAMPLE 2: Turn off siren sound numbers 4 and 6, then turn on QuietChirps:
This time, we will change the settings of three different features. This time, you’ll hear
the appropriate chirp confirmations, but we won’t make note of them in the instructions
below:
1. Enter program mode (step 3 above).
2. Latched, center to select column 1.
3. Four momentaries, (wait for the one-chirp “feature off” confirmation), then 6
momentaries to jump to row number 6.
4. Four latched-center presses to select column 4.
5. One momentary, (wait for the two-chirp “feature on” confirmation), then turn the
ignition off and you’re done.
You just changed the settings of three different features. It’s so easy, you could even do it
while driving. To set all three features back to their factory settings, just repeat steps 1-5.
Adding new remote controls
For other drivers in your family, or if you wish to control IntelliGuard systems on your
other cars with the same remote control, you can buy additional remote controls from
any Clifford Dealer (or call our 24-hour Customer Service Department at 800-824-3208)
and program them into the system yourself. Each IntelliGuard 800 will respond to as
many as four 12-channel remote controls. To add a new remote control to the system,
use the procedures noted in the User-selectable features section on pages 20–22.
How to erase the codes of lost or stolen remote controls
If one of your remote controls is ever lost or stolen, you can erase its digital codes from
the system memory to make sure that the missing remote control can never be used to
disarm your system. To do so, use the “Erase all channels” feature (feature column 2,
row 6 on the Matrix of user-selectable features on pages 21–22). This will clear all
remote control codes from the system memory. Then simply program each remaining
and/or replacement remote control as noted in the Adding new remote controls section
above.
© Copyright Clifford Electronics, Inc., 1994
31-072C/IG8OM/494
23
Download PDF

advertising