Operating instructions | Cobra Electronics 2010 GTL WX Two

When using electrical products, basic precautions should always be followed including:
1. Read these Instructions - All the safety and operating instructions should be read before
the product is operated.
2. Keep these Instructions - The safety and operating instructions should be retained
for future reference.
3. Heed All Warnings - All warnings on the product and in the operating instructions
should be adhered to.
4. Follow all Instructions - All operating and use instructions should be followed.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings, install in accordance with the manufacturer s
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third prong is provided for your safety.
If the provided plug does not fit into your outlet consult an electrician for replacement of
the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as when the power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. Warning - To reduce the risk of fire or electric shock, do not expose this apparatus to
rain or moisture.
16. Power Source - This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your home, consult
your product dealer or local power company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
17. Power Lines - An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna system, extreme care should be
taken to keep from touching such power lines or circuits as contact with them might be fatal.
18. Overloading - Do not overload wall outlets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
19. The apparatus shall not be exposed to dripping or splashing and no objects filled
with liquids, such as vases, shall be placed on the apparatus.
20. Caution - Do not attempt to service this product yourself as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all servicing
to qualified service personnel.
21. Replacement Parts - When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the
same characteristics as the original part. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
22. Safety Check - Upon completion of any service or repairs to this product, ask
the service technician to perform safety checks to determine that the product is in
proper operating condition.
23. Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling
only as recommended by the manufacturer.
Preparation of Use
There is a screw to protect the phonograph chassis
during transportation.
Turn the screw clockwise with a coin to its lowest
position before you use the phonograph for the
first time.
Basic Operation
Power on.
Connect the power plug into the wall
Select the source.
Adjust the volume.
Rotate the FM/AM/CD/PHONO knob to
select PHONO.
Listening to CD
Rotate the FM/AM/CD/PHONO knob
to select CD.
2 Open the tray, and place the CD on the tray.
3 Close the tray and start playing the CD.
CD s should be placed in their trays with the label side up.
The CD will start playing from the first track.
C Press the F.F button once to go the start of the
next track.
A Stopping the CD play.
Press the F.R button once to go back to the start of
the current track. Press the F.R button twice to go
back to the start of the previous track.
B Pausing the CD play.
Pressing the PLAY/PAUSE button will restart
playing the CD.
Do not switch off the unit during CD-function, because
it will damage the unit.
Listening to CD
Programmed playback.
To repeat a single or the entire disc.
This feature allows you to program up to 32
tracks on a disc for playback in any desired
Note: You cannot program tracks while a disc
is playing. If the disc is playing press the STOP
button first before beginning the programming
steps below:
Press the REPEAT button once. The
Repeat indicator flashes. Press the
F.R or F.F buttons to select the desired
track, then press the PLAY/PAUSE
button to begin repeat Playback of the
selected track.
Press the REPEAT button twice. The
repeat indicator remains 'on' . Press
the PLAY/PAUSE button to begin
repeat Playback of the entire disc.
1.) Press the PROGRAM button to enter the
Program Mode. The Program number briefly
shows '0 1', then the Program indicator flash.
To cancel Repeat Playback press the REPEAT
button until the Repeat Indicator goes 'off ' .
Repeat Playback is also cancelled by pressing
the STOP button, or setting the Function selector
to the AM , FM or PHONO position.
2.) Press the F.R or F.F buttons to select the first
track number you wish to enter in the program
memory, the track number will flash.
Example: Track Number '0 8'.
Program Repeat Playback
When Programmed Playback begins press the
REPEAT button twice to activate the all tracks
repeat feature.
The Repeat Indicator lights and all the tracks in
your programmed sequence will be repeated
3.) When the desired track number appears
on the display, press the PROGRAM button
again to enter that track in memory. The
Program number will shows '0 2'.
4.) Repeat Steps 2-3, selecting a different track
number each time until you have entered up to
32 tracks in the program memory.
Note: You may program the same track number
to play multiple times in the program sequence
if desired.
5.) Press the PLAY/PAUSE button to begin
Programmed playback. The Program indicator
stops flashing and remains 'on'. Playback will
begin with the first track you programmed and
will continue until the last programmed track
has played.
6.) After the last track has played the player
stops and the display shows the total number
of tracks on the disc. However the program
sequence remains in the memory.
To cancel Programmed Repeat Playback press the
STOP button until both the Program and Repeat
Indicators go 'off '.
Random Playback.
In playing or STOP mode, press the RANDOM
button, a cycle mark will be showed, when the
display shows a random tack number, playback
will begin automatically.
The programmed sequence may be cancelled by,
Pressing the open button, STOP button, switching to
the AM, FM or PHONO or shutting the system 'off '.
To cancel Random Playback press the STOP button.
Listening to the Radio
1 Rotate the FM/AM/CD/PHONO knob to
select FM or AM.
A Antenna
For optimal FM reception be sure to stretch the built-in
FM antenna wire located at the lower back of the unit
and move it around until the station you have tuned in
is being received clearly.
2 Tune to the desired frequency.
Output Power
: 2.0W + 2.0W
FM frequency Range : 87.5 to 108.5MHz
AM frequency Range : 525 to 1710KHz
: Impedance: 8 ohms
Input power: Max.3W
Power source
:120V AC, 60Hz
Power Consumption
Dimension(W X H X D) :19 X 13.9 X 11.9 (approx.)
Care and Maintenance
To remove a disc from its storage case, press down on the center of the case and lift the disc out, holding it
carefully by the edges.
Fingerprints and dust should be carefully wiped off the disc's recorded surface with a soft cloth. Unlike
conventional records, compact discs have no grooves to collect dust and microscopic debris, so gently wiping
with a soft cloth should remove most particles. Wipe in a straight line from the inside to the outside of the disc.
Small dust particles and light stains will have absolutely no effect on reproduction quality.
Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents or abrasive cleaners to clean
the disc. If necessary, use a CD cleaning kit.
Never write on or affix labels to the surface of compact discs.
You should care for the cabinet as you would care for any piece of fine furniture. When the cabinet becomes dusty
wipe it with a soft, non-abrasive dust cloth. If the cabinet becomes smudged with fingerprints you may use any
good quality commercial dusting and polishing spray cleaner, however avoid spraying the plastic or metal parts of
this system. We recommend that you spray the cleaner on your dust cloth, not directly on the cabinet, to avoid
getting any of the spray on the plastic or metal parts.
Troubleshooting guide
In case of trouble with the unit, please look through this chart and see if you can solve the problem by yourself before calling
your dealer.
Power does not come on when the
power switch is pressed
Unit is unplugged
Connect the unit to the AC power
No sound comes out of the speakers
The volume is turned down(to MIN)
The input selector does not match the
playback source
Adjust the volume
Re-select the input source
The sound is noisy
Can not listen to any station, or signal
appears weak
The unit is too close to a TV set or
another similar appliance
The station is not tuned in properly
A TV set is being used nearby
Turn off the TV or other appliance, and
relocate the unit
Tune in the station correctly
Turn off the TV set
The sound is distorted
The antenna is not oriented properly
Play stop immediately after starting to
play the CD, or play pauses or stops
during play
No sound
Specific CD is noisy, or playback stops
or skips
The CD is inserted upside down
The CD is dusty or dirty, or there is
condensation on the CD
Re-orient the antenna until reception
Insert the CD with the printed side
upper most
Clean and dry the CD
press the PLAY/PAUSE button
The CD should be changed
The CD player is paused
The CD is scratched, damaged or
The disc is very dirty
Clean the CD
Download PDF