Instruction manual | COBY electronic TFDVD2274 TV DVD Combo User Manual

TFT LCD Widescreen Television
Instruction Manual
TFDVD1574/1973/2274
Please read this manual carefully before connection and use
Precautions
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
For Customer Use:
Enter below the serial number that is located on the
rear of the unit. Retain this information for future reference.
Model No.
Serial No.
Caution:
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer to manual for servicing instructions.
Power Supply:
Connect one end of the supplied power cord to the power jack on the unit rear panel and the other end to the AC100-240V wall outlet. If the unit will not be used for a long time, disconnect the plug from the outlet.
Power Management:
••
••
Before plugging the power cord into the AC outlet, make sure that all the connections have been properly
made.
If the unit will not be used for a long period of time, disconnect the power and remove the batteries
from the remote.
Precautions
FCC Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
•• This device may not cause harmful interference, and
••
This device must accept any interference received, including interference that may cause undesired
operation.
Note:
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
••
Reorient or relocate the receiving antenna.
••
Increase the separation between the equipment and receiver.
••
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
••
Consult the dealer or an experienced radio/TV technician for help
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of the FCC rules. Do
not make any changes or modifications to the equipment unless otherwise specified in the manual. If such
changes or modifications should be made, you could be required to stop operation of the equipment.
LCD Information
The LCD panel used in this television contains millions of thin film transistors that have been manufactured
using a high-technology process to deliver a crisp, clear, and detailed picture. Occasionally, a few of these
transistors may become stuck or non-active; please note that this does not affect the performance of the
television.
Copyright Protection
Unauthorized copying, broadcasting, public performance, and lending of disks are prohibited. This product
incorporates copyright protection technology that is protected by method claims of certain U.S. patents and
other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this
copyright protection technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
Important Safety Instructions
Read Instructions: All the safety and operating instructions should be read before the product is operated.
Retain Instructions: The safety and operating instructions should be retained for future reference.
Heed Warnings: All warnings on the product and in the operating instructions should be adhered to.
Follow Instructions: All operating and usage instructions should be followed.
Cleaning: Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
666 Attachments: Use only attachments recommended by the manufacturer. Use of other attachments may
be hazardous.
777 Water and Moisture: Do not use this product near water (e.g., near a bath tub, washbowl, kitchen sink, laundry tub, in wet basements, or near a swimming pool and the like).
888 Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. Use only
with carts, stands, tripods, brackets, or tables recommended by the manufacturer
or sold with the product. Any mounting of the product should follow the
manufacturer ’s instructions and should use a mounting accessory
recommended by the manufacturer.
999 A product and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the product and cart
combination to overturn.
1111 Ventilation: Slots and openings in the cabinet are provided for ventilation
to ensure reliable operation of the product and to protect it from
overheating. These openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer instructions have been adhered to.
1111 Power Sources: This product should be operated only from the type of power source indicated on the
rating label. If you are not sure of the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery power or other sources, refer to the
operating instructions.
1111 Grounding or Polarization: This product may be equipped with a polarized alternating-current line plug
that has one blade wider than the other. This plug will only fit into the power outlet in one direction. This
is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the direction of the
plug. If the plug should still fail to fit, contact an electrician to replace the obsolete outlet. Do not defeat
the safety purpose of the polarized plug.
1111 Power-Cord Protection: Power supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and at the point which they exit from the product.
1111 Protective Attachment Plug: The product may be equipped with an attachment plug with overload
protection. This is a safety feature. See the operating instructions for replacement or directions to
reset the protective device. If replacement of the plug is required, be sure the service technician has
used a replacement plug that has the same overload protection as the original plug as specified by the
manufacturer.
1111 Lightning: For added protection for this product, unplug it from the wall outlet and disconnect the antenna
or cable system during a lightning storm or when it is left unattended and unused for long periods of time.
This will prevent damage to the product due to lightning or power-line surges.
1111 Power Lines: An outside antenna system should not be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be taken to keep from touching such power lines or
circuits, as contact with them might be fatal.
1111 Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this
can result in a risk of fire or electric shock.
1111 Object and Liquid Entry: Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or shout-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
1111 Servicing: Do not attempt to service this product yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
111
222
333
444
555
Important Safety Instructions
2222 Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions: a) when the power-supply or plug is damaged; b) if
liquid has been spilled or if objects have fallen into the product; c) if the product has been exposed to
rain or water; d) if the product does not operate normally by following the operating instructions. Adjust
only those controls that are covered by the operating instructions as improper adjustment of other
controls may result in damage and will often require extensive work by a qualified technician to restore
the product to its normal operation; e) if the product has been dropped or damaged in any way; f) when
the product exhibits a distinct change in performance—this indicates a need for service.
2222 Replacement Parts: When replacement parts are required, be sure that your service technician has used
replacement parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
2222 Safety Check: Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks to ensure that the product is in proper operating condition.
2222 Wall or Ceiling Mounting: The product should be mounted to a wall or ceiling only as recommended by
the manufacturer.
2222 Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that produce heat.
2222 Outdoor Antenna Grounding: If an outside antenna is connected to the product, be sure the antenna
system is grounded so as to provide some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANS/NFPA 70 provides information with regard to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge
unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode (see figure).
Table of Contents
Table Of Contents
Precautions
Important Safety Instructions
Main Feature-----------------------------------------------------------------------------------------------------------------------------1
Package Contents-----------------------------------------------------------------------------------------------------------------2
Unit View-------------------------------------------------------------------------------------------------------------------------3
Remote Control -------------------------------------------------------------------------------------------------------4,5,6
Cable Connections------------------------------------------------------------------------------------------------------------7,8
TV Function----------------------------------------------------------------------------------------------------------------9,10,11,12
AV Function-----------------------------------------------------------------------------------------------------------------------------13
PC Function----------------------------------------------------------------------------------------------------------------------------14
DVD Operation---------------------------------------------------------------------------------------------------------------------15,16
Playback Function----------------------------------------------------------------------------------------------------------------17,18
DVD Setup----------------------------------------------------------------------------------------------------------------19,20
Troubleshooting -----------------------------------------------------------------------------------------------------------------------21
Specifications ----------------------------------------------------------------------------------------------------------------------22,23
Main Features
Multiple Mode
TV
AV
S-VIDEO
COMPONENT
DVD
HDMI
VGA
High Quality Property
High Resolution
Adopt an MPEG2 decoding format to achieve horizontal resolution more than 500 lines.
Superior sound
Built-in Dolby Digital decoder to output high quality sound effects.
Screen
Support the picture size of a normal screen (4:3) and a wide screen (16:9)
LCD (Liquid Crystal Display)
Designed with color TFT liquid crystal display clearly shows the data.
Advanced Playing Features
Compatibility
DVD, CD, MP3, CD-R,CD-RW, JPEG discs compatible.
All Playback Functions
Fast forward and reverse, repeat playback, program playback.
NOTE: It is normal for a TFT screen to experience some light or dark spots appearing on the LCD screen.
1
Package Contents
Please make sure the following items are included with your product. If any items are missing, contact your
dealer.
OPEN/CLOSE
C.C MTS/SOUND
DVD SETUP
a.
EXIT
MODE
SLEEP
CH-LIST
EPG
FAV
FORMAT
TITLE
INFO
ANGLE SUBTITLE MENU
PLAY/PAUSE STOP SLOW/STEP
F.BWD
F.FWD
PROGRAM GOTO
b.
a, Main Unit
b, Power Cord & RCA Cable
c, Remote Control Unit
c.
2
PREV
NEXT
ZOOM REPEAT
Unit View
1
6
7
8
9
10
11
12
13
2
4
3
14
15
9. VOL+/10. CH+/11. LCD SETUP
12. MODE
13. POWER
14. MMC/SD/MS CARD SLOT
15. USB PORT
16. UNIT STAND
100mm
16
17. PHONE JACK
18. PC AUDIO IN
19. TV ANTENNA
<
1. TFT SCREEN
2. REMOTE SENSOR
3. POWER INDICATOR
4. SPEAKER
5. DISC SLOT
6. OPEN/CLOSE
7. PLAY/PAUSE
8. STOP
5
>
20. AUDIO IN((R/L)
>
21. VIDEO IN
VESA Standard
mounting thread
x4
22. S-VIDEO IN
<
100mm
>
23. COMPONENT IN
24. VGA IN
25. HDMI
Unit Stand
Plastic part
x2
(e.g. TFDVD1973 Rear Cabinet)
26. POWER JACK
Wall Mounting
••
••
Pinch the edge of the plastic part and remove it from its fixture. Release the screws inside, take off the
unit stand.
Use the VESA standard mountings to fix the unit on the wall. Take care when mounting, it may cause
damage or serious injury should it fall from its mountings. See the Specification page for VESA
information.
3
Remote Control
Remote Control Drawing
1. POWER
Press to enter/exit the standby mode.
OPEN/CLOSE
2. CC
1
6
Set the Close Caption mode as CC on Mute/Off/On.
3. VOLUME +/12
Press to adjust the volume.
4. LCD SETUP
Press to show the TV setup menu.
7
C.C MTS/SOUND
8
5. DVD SETUP
2
Press to show the DVD setup menu.
9
3
6. OPEN/CLOSE
4
Press to take in/out the disc.
10
7. RETURN
Press to locate the previously viewed channel.
11
5
8. MTS/SOUND
DVD SETUP
EXIT
MODE SLEEP CH-LIST INFO
17
Under the DVD mode, press to select the audio mode.
13
14
18
Under the TV mode, press to set the audio language.
EPG
FAV FORMAT
19
15
9. CHANNEL +/20
16
TITLE ANGLE SUBTITLE MENU
29
Press to skip channels.
21
30
22
PLAY/PAUSE STOP SLOW/STEP
10. Direction & OK button
31
23
32
Press the direction buttons to move between the
F.BWD F.FWD PREV
NEXT
24
33
25
options while working with the menu.
34
PROGRAM GOTO ZOOM REPEAT
26
35
Press OK to confirm settings.
27
36
28
11. EXIT
Press to exit the menu setup.
12. Numeric key pad
Press to input data.
13. MODE
Press to show the mode selective menu (TV, AV, S-VIDEO,
COMPONENT, DVD, PC).
14. SLEEP
Press to set the sleep timer.
15. EPG
Press to show the Electronic Program Guide.
16. FAV
Press to show the Favorit Channel List. If no channel is set on the list, the button does not function.
17. INFO
Press to show the current working status.
18. CH-LIST
Press to show the channel list.
19. MUTE
Press to muffle/release the sound.
20. FORMAT
Press to change the display format as Zoom, Cinema or Full.
4
Remote Control
Remote Control Drawing
21. TITLE
Press to show the title menu under the DVD mode.
22. ANGEL
Press to select the available camer angles under the DVD mode.
23. Play/Pause
Press to start/hold playback under the DVD mode.
24. Stop
Press to stop plalyback.
25. F.BWD
Press to search fast backward through a disc.
26. F.FWD
Press to search fast forward through a disc.
27. Program
Press to access the program menu.
28. Goto
Locate the desired section in a disc.
29. Menu
Press to show the root menu under the DVD mode.
30. Subtitle
Press to show the subtitle under the DVD mode.
31. A-B
Repeat a specified section A-B on a disc.
32. Slow/Step
During playback, press the button to start slow-motion playback.
Under the pause mode, press the button to play a disc frame by frame.
33. NEXT
Repeatedly press the button to skip forward through a disc.
34. PREV
Repeatedly press the button to skip backward through a disc.
35. Repeat
Press to repeat a special section on a disc.
36. Zoom
Press to zoom in/out the picture.
5
Remote Control
Preparation
••
Remove the battery compartment cover located on the rear of the remote control. Insert 2 x “AAA” batteries, making sure to match their polarities (+/-) to the markings on the inside of the compartment. Replace the cover.
••
Batteries in the remote will last for approximately 6 months under the normal use. Replace the batteries if the remote control does not work. Do not mix old with new batteries, or different types of batteries.
••
Remove the batteries from the remote if it will not be used for a long period of time.
Warnings:
The battery used in this device may present a fire or chemical burn if mistreated. Do not recharge,
disassemble, incinerate, or heat the battery (~212ºF).
Keep batteries away from children.
Using the Remote Control
To use the remote, point it at the remote sensor within 20 feet , by an angle of ±30 degrees.
7
s
OPEN/CLOSE
RETURN
The operating distance may vary depending on the brightness around.
Notes:
111 Do not point bright lights directly at the remote control sensor.
222 Do not place objects between the remote control unit and the remote control sensor.
333 Do not use this remote control unit while simultaneously operating the remote control unit of any other equipment.
6
Cable Connections
Figure. Cable connections
Set the unit into the relative input mode
to enable the signal pass.
External AV Source
Antenna/Power Connection
111 Connect TV RF sources to the antenna port. TV RF signals include: receiving antenna/CATV net. You
can use 75 Ohm coaxial cable to connect outdoor antenna.
222 Insert one end of the supplied power cord to the player’s power jack and the other end to the 110-240V
AC wall outlet.
Compoent Input (Y Cb/Pb Cr/Pr)
The component port is capable of accepting high-definition signals from standard video sources. (e.g., cable/
satellite boxes, DVD players, VCRs, etc.)
111 Connect the Y/Pb/Pr port by the component cable to input the video signal.
222 Connect “R” "L" port by the supplied AV cable to input the audio signal. The red/white plug of the AV
cable is for the audio conneciton and the yellow plug for the video connection.
S-Video Input
The S-Video port is capable of accepting signals from standard video sources. (e.g., cable/satellite boxes,
DVD players, VCRs, etc.)
111 Connect the S-Video port by the S-Video cable to input the video signal.
222 Connect the AUDIO-L/R port by the supplied AV cable to input the audio signal.
AV Input
The CVBS port is capable of accepting signals from standard video sources(e.g., cable/satellite boxes, DVD
players, VCRs, etc.)
111 Connect the VIDEO port with the yellow plug of the the supplied AV cable.
222 Connect the L/R port with the red & white plug of the supplied AV cable to input the audio signal.
VGA Input
The VGA port of the TV is capable of accepting high-definition signals from computers with a VGA output
jack. When used as a computer moniter, connect the VGA jack and the PC Audio In jack with a 15-Pin D-Sub
cable and a 3.5mm stereo audio cable.
HDMI Input
HDMI (High Definition Multimedia Interface) is a new type of connection that transmits digital audio and video
signals simultaneously over a single cable. A HDMI cable is required for the HDMI connection.
These HDMI input connectors are capable of receiving video at resolutions up to 1080p (1080-progressive).
7
Cable Connections
Figure. Cable connections
Component Input
NOTE:
We supply the AV cable and the power cord
with this product.
The white/red plug of the AV cable is for the
audio connection and the yellow plug for the
video connection.
The white/red plug of the AV cable can also
be used separately to input the audio signal
in the S-video/Component connection.
S-Video Input
AV Input
NOTE:
111 Be sure to have all necessary connections properly done before connect the power supply.
222 When input the AV signal, refer to the manual of the external sources as well.
8
TV Function
Preparations
111
222
333
444
Connect the cables.(Refer to the “Cable Connections” section for details).
Press the POWER button to turn on the player.
Press the MODE button to select the TV signal mode.
Press the CH+/- buttons to skip channels. Or you can press the number buttons to input channels
directly. For the initial use, you need to scan channels under the Channel Menu. See the "Channel Menu"
section for details.
TV Setup Menu
Various features can be preset through the TV setup menu, please read this section carefully.
•• Press LCD SETUP to display the setup menu, TV setup menu consists of PICTURE, AUDIO, TIME,
SETUP, LOCK as well as CHANNEL.
•• Press the left/right direction button to select the desired submenu, press OK to enter.
While working with the menu,
111 Press the up/down direction button to select the option.
222 Press the left/right direction button to adjust.
333 Press LCD SETUP to exit/back up menu.
Warm
Picture Menu
ITEM
DESCRIPTION
Picture Mode Setup the picture mode (Personal, Standard, Dynamic, Soft).
Contrast Adjust the display contrast
Brightness Adjust the display brightness
Color Adjust the display color
Tint
Adjust the display tint
Sharpness Adjust the image sharpness
Color Mode
Set the color mode (Normal, Warm, Cool).
9
TV Function
Audio Menu
ITEM
DESCRIPTION
Sound Mode Set the sound mode. (Standard, Music, Movie, Personal).
Bass Adjust the bass.
Treble Adjust the treble. Balance Adjust the sound balance.
Surround Set the audio surround effect on/off.
AVC Set AVC on/off.
MTS Set the MTS audio for the ATV mode. (Mono, Stereo, SAP)
Audio Set the audio language. (English, French, Spanish)
Language
Time Menu
ITEM
DESCRIPTION
Sleep Timer The unit will shut down automatically on the Sleep Time.
The available option is 5/10/15/30/45/60/90/120/180/240 min, Off. The count down would start immediately after setting.
You can access this function by repeatedly pressing the SLEEP button on the remote also. To check the timer left, press the SLEEP button on the remote once. To cancel the sleep timer, set the timer to Off.
Time Zone
Set the DTV time zone.
(Pacific, Alaska, Hawaii, Eastern, Central, Mountain)
Daylight Saving Time Set the DTV daylight saving function on/off.
Clock Display the DTV clock information.
10
TV Function
Setup Menu
ITEM
DESCRIPTION
Menu Language Set the menu language.
Transparency Set the OSD(On-Screen-Display) transparency on/off.
Zoom Mode Set the display aspect ratio. (4:3, Cinema, Normal, 16:9)
Noise Reduction Adjust the screen noise appearance. (Weak, Middle, Strong, Off)
Closed Caption
Press the right direction button to access the Closed Caption menu.
CC Mode - Set the CC mode. ( Off, On, CC On Mute)
Basic Selection - Set the basic CC type. (CC1~4, Text 1~4)
Advanced Selection - Set the advanced CC type for DTV. (Service 1~6)
Option - Press the right direction button to enter Option. Under the option menu, set Mode as Custom to edit the DTV CC type to your own liking.
DLC Set DLC on/off
There are four options listed under the Closed Caption menu.
Restore Default Set the player to the factory default.
Lock Menu
ITEM
DESCRIPTION
Enter You are required to enter the 4-digit password to access the Lock menu. The initial password is 0000.
Change To change the password, input the old password - - > input the
Password
new password- - >verify again.
Please remember the password since the players’s reset function would not revert the password.
System Lock Set the system lock funtion on/off.
Set the lock function On to access the parental control setup.
Unrated Lock Set Unrated Lock on/off.
US Setup the US parental control.
TV(TV Rating) - Y, Y7, G, PG, 14, MA.
Press the direction buttons to move between options, press OK to set block. To release, press OK again. MPAA(Movie Rating) - PG-13, R, NC-17, X, N/A, G, PG)
Press the left/right direction button to set the movie rating.
Canada Setup the Canada parental control
Canada English - G, PG, 14+, 18+, E, C, C8+.
Canada French - E, G, 8ans+, 13ans+, 16ans+, 18ans+.
RRT Setting Set the rating region table.
Reset RRT Restore RRT to the default. 11
TV Function
Channel Menu
ITEM
DESCRIPTION
Air/Cable
Setup the antenna type as Air or Cable.
Auto Scan
Search channels automatically. Select this option, press the right button to start searching, press MENU to stop. When use Cable system, you need to select the cable system first from AUTO, STD, IRC and HRC before scaning.
Favorite
Make the favorite channels collection. Select this option, press the right direction button to access the Favorite List.
In the Favorite List, press the up/down direction button to select the desired channel. Press OK to set it as the favorite channel. To release, press OK again.
Press the left/right button to turn pages in the FAV list.
Show/Hide Hide the unwanted channels. Select this option, press the right direction button to access the Show/Hide menu. In the Show/
Hide menu, press the up/down direciton button to select the channel, press OK to hide the channel, press OK again to release. Press the left/right button to turn pages in the Show/
Hide list.
Channel No Press the left/right direction button to select the channel.
Channel Label Edit the channel label.
1. Select the channel you want to put a label.
You can use the Channel No option or directly locate the channel by the number button/CH+/- button.
2. Select “Channel Label”, press the right direction button to show the edit menu. In the menu, press the left/right direction button to move left/right, press the up/down direction button to change characters.
DTV Signal
Display the DTV signal intensity.
12
AV Function
The player’s AV input function enables the user to view programs from external input sources.
111 Connect the external AV signal source. Refer to the “Cable Connection” section for details
222 Press the MODE button to select the relevant AV mode (AV, S-Video, Component, HDMI)
AV Setup Menu
Various features can be preset through the AV menu.
•• Press the LCD SETUP button to display the AV menu. AV setup menu consists of PICTURE, AUDIO,
TIME, SETUP as well as LOCK.
•• Press the left/right direction button to select the desired sub-menu, press OK to enter.
While working with the menu
111 Press the up/down direction buttons to select the desired item.
222 Press the left/right direction button to adjust.
333 Press LCD SETUP to exit/back up the menu.
Warm
NOTE: Please see the TV section for menu descriptions
13
PC Function
You can use the unit’s TFT LCD as your computer’s monitor.
111 Shut down the unit and the computer, connect the VGA jack and PC Audio In jack. See the “Cable
Connection” section.
222 Turn on the units and press the MODE button to select VGA
PC Setup Menu
Various features can be preset through the PC menu.
•• Press the LCD SETUP button to display the PC menu. PC setup menu consists of PICTURE, AUDIO,
TIME as well as SETUP.
•• Press the left/right direction button to select the desired sub-menu, press OK to enter.
While working with the menu
111 Press the up/down direction buttons to select the desired item.
222 Press the left/right direction button to adjust.
333 Press LCD SETUP to exit/back up the menu.
NOTE: Please see the TV section for menu descriptions.
Adjust the PC Screen
Upon switching to the PC mode, the moniter will be automatically regulated for a
proper functioning. If the result is not up to your expectation, please perform the
following steps to adjust the screen manually .
111 Enter the “Advanced” sub-menu from the SETUP menu, select “Auto” and
press the left/right direction button to adjust the monitor automatically.
222 Or if you still have problem with the monitor after, adjust “H-Pos”, “V-Pos”, ”Clock“ as well as “Phase” accordingly under the SETUP menu.
14
DVD Operation
Preparation
After all necessary connections have been made, press POWER to turn on the player and then press the
MODE button to select DVD. The following discs can be read by the player : DVD /CD / MP3 /JPEG.
Disc Loading
1. Put the disc slightly into the disc tray.
2. The disc will be taken automatically into the tray. > Label Side
Warning: Do not play poor quality discs that may damage the player's lens.
DVD Playback
MENU
Normally a DVD disc consists of several titles and chapters. The root menu will be displayed automatically once the disc data is recognized by the player. Press the direction buttons to select the desired title/chapter from the menu and press OK to play. During playback, press MENU to display the root menu. Some discs start playback automatically.
SUBTITLE
Press SUBTITLE button to select subtitle language for multi-subtitle discs.
ANGLE
Press the ANGLE button to select the angle. A DVD can be recorded from various camera positions, which lets you enjoy the same scene from different perspectives. In this case, you'll usually find a marking on the DVD sleeve.
VOLUME
During playback, press the VOL+ button to increase the volume and press the VOL- button to decrease the volume.
15
DVD Operation
CD Playback
The player will play all tracks on a CD disc by default.
JPEG Playback
JPEG is a common picture format that requires small amounts of storage per image and has low loss in
resolution. Hundreds of pictures can be stored on a disc in this format. In order to view JPEG photo albums,
you can ask your film development company to make a "PICTURE CD" when they develop your film.
Normal Playback
Load a JPEG disc in.
Press the direction buttons to select the target file and press OK to access.
Picture Rotation
There are four kinds of rotational modes: Inversion, Enantiomorphism, rotate left and rotate right. Press direction buttons to select:
"UP" ----- Inversion/Normal
"DOWN" ----- Enantiomorphism/Normal
"LEFT" ----- Rotate left
"RIGHT" ----- Rotate right
Zoom
Press ZOOM button to zoom in/out picture.
Press direction buttons to move the zoomed picture.
During playback, press the STOP button to return to the previous menu.
NOTE: Depending on how the disc was made, a JPEG disc may allow playback , but not rotation or
zooming of the images.
USB/Card Access
Set the unit into the DVD mode, plug the USB or Card into the
corresponding slot, the player starts reading data. When the USB/Card
is detected, the screen displays a working menu, press the direction
buttons to select the file, press OK to start playback. To disconnect the
device, just unplug it from the port when it is not in working.
16
Playback Function
Start Playing
Press PLAY/PAUSE to start playback
Pause Playing
During playback, press PLAY/PAUSE once to hold playing, press it again to resume.
Stop Playing
Press STOP once to stop playback at a time point. (Pre-stop mode) It will resume from where it was stopped.
Press it twice to stop playback completely.
Repeat Function
Use the REPEAT button to perform the repeat function.
111 Repeatedly press the REPEAT button to cycle through the repeat modes as below,
DVD Mode
REP: CHAPTER - - > REP:TITLE - - > REP:ALL- - > REP:OFF
CD Mode
REP: 1 - - > REP:ALL - - > REP:OFF
222 Use the A-B button on the remote to repeat a section A-B. Press A-B once to set the starting point A,
press it twice to set the ending point B, the player would start playing section A-B. To cancel, press A-B.
NOTE: Some discs do not support the repeat function.
Search Function
Go to the desired section in a disc.
Press the GOTO button, below picture appears on the screen.
DVD
Search by title /chapter/time
DVD
TT 06 / 12 CH
Title
CD/MP3
Search by track / time
TRK 06 / 12
Track
018 / 029
Chapter
00 : 01 : 26
Time
00 : 01 : 26
Time
111 Press the direction buttons to move between title/chapter/time entry, press the numeric buttons to input
data. Press the OK button to start search.
222 Press GOTO once again to exit.
NOTE: Some DVD discs do not support the search function.
Fast Playback
Press F.FWD/F.BWD on the remote to go fast forward/backward through a disc. Repeatedly press the button
to change the search speed as below.
17
Playback Function
Slow Playback
During playback, repeatedly press the SLOW/STEP button to start slow motion playback.
Zoom Function
Repeatedly press the ZOOM button to achieve the following zoom effect.
NOTE: There is no zoom function for MP3 or CD discs.
Programming Chapters/Tracks
You can store up to 16 programs.
111 Press the PROGRAM button to display the program menu.
e.g. DVD Mode
PROGRAM
T C
T C
T C
T C
1 -- : --
5 -- : --
9
-- : --
13 -- : --
2 -- : --
6 -- : --
10 -- : --
14 -- : --
3 -- : --
7 -- : --
11 -- : --
15 -- : --
4 -- : --
8 -- : --
12 -- : --
16 -- : --
PLAY
222
333
444
555
CLEAR
Press the direction buttons to move between the input fields and press the number buttons to input data.
Press direction buttons to select "Play " and press OK to start playback.
To clear, select “CLEAR” from the menu and press OK.
To quit, press the Program button.
18
DVD Setup
Various features can be preset through the DVD setup menu. Press the DVD SETUP button to show the
DVD menu.
SYSTEM SETUP
TV SYSTEM
SCREEN SAVER
POWER RESUME
TV TYPE
PASSWORD
RATING
DEFAULT
EXIT SETUP
While working with the setup menu:
111 Press the direction buttons to select the desired item.
222 Press the right direction button or the OK button to confirm.
333 To exit, press DVD SETUP again.
System Setup
111 TV System - Select the TV System from NTSC/PAL/AUTO. The default setting is PAL. (The TV System
for north America is NTSC. AUTO should only be used if you have a Multi-System TV).
222 Screen Saver - Set the Screen Saver ON/OFF. The default setting is On. The screen saver is useful to
prevent your display from becoming damaged. If the Screen Saver is set ON, the screen saver picture
appears when you leave the player in the stop mode for about a few minutes. Press any button on the
unit/remote to exit the screen saver.
333 Power Resume - Set the power resume function On.Off. The default setting is Off.
444 TV Type - Set the screen aspect ratio as 4:3 PS(Pan Scan), 4:3 LB(Letter Box) or 16:9(Wide Screen).
4:3 LB(Letter Box): This is selected when the unit is connected to a normal TV. Wide-screen images are
shown on the screen with black belt on the top and bottom.
4:3 PS(Pan Scan): This is selected when the unit is connected to anormal TV. Wide-screen images are
shown on the screen with some parts cut out automatically.
555 Rating - There are eight levels of Parental Control. Level one opens discs to people of all ages, level
eight is suitable only for adults. To change the parental control setting, a 4-digit code is required to be
input first. (The default code is 8888). When the input code is confirmed, the level setting menu will
appear, select the appropriate level by the UP/DOWN button and press OK to confirm.
19
DVD Setup
666 Password - Move the cursor to the PASSWORD prompt and press OK. Input the password 8888, if it is
the first use. After confirmation, you will be required to input a new 4-digit code, and verify again.
777 Default - This function allows you to set the unit back to the factory default.
Language Setup
Item
Instruction
Default
OSD Language Setup the OSD language. English
Audio Language Setup the audio language.
English
Subtitle Language Setup the subtitle language. When OFF is selected, the subtitle will not be displayed.
English
Menu Language Setup the menu language. English
20
Troubleshooting
If you have a problem with this device, please read the troubleshooting guide section and check our website
at www.cobyusa.com for Frequently Asked Questions (FAQs) and firmware updates. If these resources do
not resolve the problem, please contact Technical Support.
Address
COBY Electronics Technical Support
56-65 Rust Street
Maspeth, NY 11378
Email
techsupport@cobyusa.com
Web
www.cobyusa.com
Phone
800-727-3592: Weekdays 8:30AM -9:00PM EST
Saturdays 9:00AM -5:30PM EST
718-416-3197: Weekdays 8:00AM -5:30PM EST
Symptom
Check and Action
No Power
••
••
••
Make sure the unit has been powered on manually.
Check if the power cord has been properly connected to the power
outlet.
Check if the main power has been switched on.
No Picture
••
••
••
Try another TV channel
Check if the system connection is proper and secure.
Check if the connection cables are damaged.
No Sound
••
••
••
••
Increase the volume.
Check if the MUTE function of the unit has been activated.
Check if the sound system has been properly set.
Check if the AV audio signal input cable has been connected properly.
Color Distorted
••
••
••
Reset the color system of the unit.
Check if the system has been properly connected.
Check if the AV video signal input cable is connected properly.
Picture and Sound
are interfered
••
••
Check if the system has been properly connected.
If using antenna, adjust the antenna.
Remote Control
does not work
••
••
••
••
Make sure the POWER button on the unit has been turned on manually.
Remove the obstacles between the remote control and the player.
Point the remote control towards the remote sensor on the player.
Check if the batteries of the remote control have been loaded with
correct polarities.
Replace the batteries of the remote control.
••
Malfunction
••
Should the player develop a malfunction, unplug the player for 30
minutes. After that, power on the player and the restore function should
reset the player.
21
Specifications
TFDVD 1574
TFT Panel
Characteristic
TV Characteristic
15.4"
Active Area
Resolution
1280 x 800 mm
Display Color
6-bit, 262.144 colors
Pixel Pitch
0.25875(H) x 0.25875(V)mm
TV System
ATSC/NTSC
Tuning System
FS with PLL
Antenna Impedance
75Ω
Power Consumption
100-240V 50/60Hz
Standard
On Working
40W(Max)
Speaker
2x(4Ω,5W)
Operating Temperature Range
0ºc-40ºc
Dimension
378X133X334 MM
Wall Mounting
VESA M4 75X75 MM
Active Area
19", 16:9
TFDVD 1973
TFT Panel
Characteristic
TV Characteristic
Resolution
1440x900 mm
Display Color
16.77 M
Pixel Pitch
0.2835(H) x 0.2835(V)mm
TV System
ATSC/NTSC
Tuning System
FS with PLL
Antenna Impedance
75Ω
Power Consumption
110-240V 50/60Hz
Standard
On Working
60W(Max)
Speaker
2x(4Ω,5W)
Operating Temperature Range
0ºc-40ºc
Dimension
460X159X423 MM
Wall Mounting
VESA M4 100X100MM
22
Specifications
TFDVD 2274
TFT Panel
Characteristic
TV Characteristic
22"
Active Area
Resolution
1680x1050 mm
Display Color
16.77 M
Pixel Pitch
0.282(H) x 0.282(V)mm
TV System
ATSC/NTSC
Tuning System
FS with PLL
Antenna Impedance
75Ω
Power Consumption
110-240V 50/60Hz
Standard
On Working
65W(Max)
Speaker
2x(4Ω,5W)
Operating Temperature Range
0ºc-40ºc
Dimension
527x167x444 MM
Wall Mounting
VESA M4, 100 X 100 MM
P/N: 907-FD15-7400-00R
Specifications and manual are subject to change without prior notice.
23
Download PDF

advertising