Operating instructions | Compaq 1683 Laptop User Manual

Operating Instructions
Link-to-Cell Cellular Convergence Solution
KX-TG7731
KX-TG7732
KX-TG7733
KX-TG254SK
KX-TG7741
KX-TG7742
KX-TG7743
KX-TG7745
Model No.
Model shown is KX-TG7731.
Before initial use, see “Getting Started”
on page 11.
Thank you for purchasing a Panasonic product.
Please read these operating instructions before using the unit and save them for
future reference.
Consulte “Guía Rápida Española”, página 73.
For assistance, visit our Web site: http://www.panasonic.com/help for customers
in the U.S.A. or Puerto Rico.
Please register your product: http://www.panasonic.com/prodreg
TG7731_41_(en-en)_1121_ver.021.p1
1
2011/11/21
12:02:11
Table of Contents
Introduction
Caller list ....................................................44
Model composition .......................................3
Accessory information ..................................4
Using Bluetooth Devices
Important Information
For your safety .............................................7
Important safety instructions ........................8
For best performance ...................................8
Other information .........................................9
Specifications .............................................10
Copying phonebook from a cellular phone
(phonebook transfer) ..................................46
Using a Bluetooth wireless headset (optional)
for landline calls .........................................47
Answering System for Landline
Setting up ...................................................11
Note when setting up .................................12
Intelligent eco mode ...................................13
Controls ......................................................13
Belt clip .......................................................15
Display/Indicators .......................................15
Initial settings .............................................17
Answering system for landline ...................49
Turning the answering system on/
off ...............................................................49
Greeting message ......................................50
Listening to messages using the base
unit .............................................................50
Listening to messages using the
handset ......................................................50
Remote operation .......................................51
Answering system settings .........................53
Link to Cell
Voice Mail Service for Landline
Link to cell feature ......................................18
Registering a cellular phone .......................18
Link to cell settings .....................................19
Intercom/Locator
Getting Started
Making/Answering Calls Using
the Handset
Making cellular calls ...................................22
Making landline calls ..................................22
Answering calls ..........................................23
Useful features during a call .......................23
Making/Answering Calls Using
the Base Unit
Making cellular calls ...................................27
Making landline calls ..................................27
Answering calls ..........................................27
Useful features during a call .......................28
Shared Phonebook
Shared phonebook .....................................30
Programming
Voice mail service for landline ....................55
Intercom .....................................................57
Handset locator ..........................................57
Transferring calls, conference calls ............58
Useful Information
Wall mounting ............................................59
Error messages ..........................................61
Troubleshooting .........................................62
FCC and other information .........................70
Guía Rápida Española
Guía Rápida Española ...............................73
Appendix
Customer services .....................................82
Warranty (For United States and Puerto
Rico) ...........................................................83
Index
Index...........................................................85
Programmable settings ..............................33
Special programming .................................40
Registering a unit .......................................42
Caller ID Service
Using Caller ID service ...............................43
2
TG7731_41_(en-en)_1121_ver.021.p2
2
2011/11/21
12:02:12
Introduction
Model composition
n KX-TG7731 series
n KX-TG7741 series
R Model shown is KX-TG7732.
R Model shown is KX-TG7742.
Base unit
Handset
Part No.
Part No.
KX-TG7731
KX-TG7731
KX-TGA470
1
KX-TG7732
KX-TG7731
KX-TGA470
2
KX-TG7733
KX-TG7731
KX-TGA470
3
KX-TG254SK
KX-TG7731
KX-TGA470
4
KX-TG7741
KX-TG7741
KX-TGA470
1
KX-TG7742
KX-TG7741
KX-TGA470
2
KX-TG7743
KX-TG7741
KX-TGA470
3
KX-TG7745
KX-TG7741
KX-TGA470
5
Series
Model No.
KX-TG7731 series
KX-TG7741 series
Quantity
Feature differences
Series
Base unit keypad/sp-phone
KX-TG7731 series
Intercom*1
«
*2
–
–
KX-TG7741 series
*1
*2
Single handset models: Intercom calls can be made between handsets by purchasing and
registering one or more optional handsets (page 5).
Intercom calls can be made between the base unit and handset.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p3
3
2011/11/21
12:02:12
3
Introduction
Accessory information
Supplied accessories
Supplied handset qty.
1 unit*1
No.
Accessory item/
Order number
Accessory quantity
A
AC adaptor/PNLV226Z
1
2
3
4
5
B
Telephone line cord/
PQJA10075Z
1
1
1
1
1
C
Wall mounting adaptor/
PNKL1001Y1
1
1
1
1
1
D
Rechargeable batteries/
HHR-4DPA
2
4
6
8
10
E
Handset cover*6/
PNYNTGA470BR
1
2
3
4
5
F
Belt clip/PNKE1132Z1
1
2
3
4
5
G
Charger/PNLC1029ZS
–
1
2
3
4
*1
*2
*3
*4
*5
*6
A
4
2 units*2
3 units*3
4 units*4
KX-TG7731/KX-TG7741
KX-TG7732/KX-TG7742
KX-TG7733/KX-TG7743
KX-TG254SK
KX-TG7745
The handset cover comes attached to the handset.
B
C
D
E
F
G
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p4
4
2011/11/21
12:02:12
5 units*5
Introduction
Additional/replacement accessories
Please contact your nearest Panasonic dealer for sales information (page 82).
Accessory item
Order number
Rechargeable
batteries
HHR-4DPA*1
R To order, please call 1-800-332-5368 or visit
http://www.panasonic.com/batterystore
Battery type:
– Nickel metal hydride (Ni-MH)
– 2 x AAA (R03) size for each handset
Headset
KX-TCA60, KX-TCA93, KX-TCA400, KX-TCA430
T-adaptor
KX-J66
Range extender
KX-TGA405*2
*1
*2
Replacement batteries may have a different capacity from that of the supplied batteries.
By installing this unit, you can extend the range of your phone system to include areas
where reception was previously not available. This product can be purchased online. Please
visit our Web site:
http://www.panasonic.com/RangeExtender
Expanding your phone system
Optional handset feature overview
Handset (optional): KX-TGA470
You can expand your phone system by
registering optional handsets (6 max.) to a
single base unit.
R Optional handsets may be a different color
from that of the supplied handsets.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p5
5
2011/11/21
12:02:12
5
Introduction
Bluetooth® devices
You can expand your phone system by registering the following units to a single base unit.
Your Bluetooth cellular phone*1: 2 max.
(for cellular calls: page 18)
Your Bluetooth headset*1: 1 max.
(for a wireless hands-free conversation: page 47)
*1
6
Your cellular phone and headset must be Bluetooth wireless technology compatible. For
more details and the list of compatible cellular phones, please visit our Web site:
http://www.panasonic.com/link2cell
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p6
6
2011/11/21
12:02:12
Important Information
R Do not allow the AC adaptor or telephone
line cord to be excessively pulled, bent or
placed under heavy objects.
For your safety
To prevent severe injury and loss of life/
property, read this section carefully before
using the product to ensure proper and safe
operation of your product.
WARNING
Power connection
R Use only the power source marked on the
product.
R Do not overload power outlets and
extension cords. This can result in the risk
of fire or electric shock.
R Completely insert the AC adaptor/power
plug into the power outlet. Failure to do so
may cause electric shock and/or excessive
heat resulting in a fire.
R Regularly remove any dust, etc. from the
AC adaptor/power plug by pulling it from
the power outlet, then wiping with a dry
cloth. Accumulated dust may cause an
insulation defect from moisture, etc.
resulting in a fire.
R Unplug the product from power outlets if it
emits smoke, an abnormal smell, or makes
an unusual noise. These conditions can
cause fire or electric shock. Confirm that
smoke has stopped emitting and contact
the Panasonic Call Center at
1-800-211-PANA (1-800-211-7262).
R Unplug from power outlets and never touch
the inside of the product if its casing has
been broken open.
R Never touch the plug with wet hands.
Danger of electric shock exists.
Installation
R To prevent the risk of fire or electrical
shock, do not expose the product to rain or
any type of moisture.
R Do not place or use this product near
automatically controlled devices such as
automatic doors and fire alarms. Radio
waves emitted from this product may cause
such devices to malfunction resulting in an
accident.
Operating safeguards
R Unplug the product from power outlets
before cleaning. Do not use liquid or
aerosol cleaners.
R Do not disassemble the product.
R Do not spill liquids (detergents, cleansers,
etc.) onto the telephone line cord plug, or
allow it to become wet at all. This may
cause a fire. If the telephone line cord plug
becomes wet, immediately pull it from the
telephone wall jack, and do not use.
Medical
R Consult the manufacturer of any personal
medical devices, such as pacemakers or
hearing aids, to determine if they are
adequately shielded from external RF
(radio frequency) energy. (The product
operates in the frequency range of
1.92 GHz to 1.93 GHz, and the RF
transmission power is 115 mW (max.).)
R Do not use the product in health care
facilities if any regulations posted in the
area instruct you not to do so. Hospitals or
health care facilities may be using
equipment that could be sensitive to
external RF energy.
CAUTION
Installation and location
R Never install telephone wiring during an
electrical storm.
R Never install telephone line jacks in wet
locations unless the jack is specifically
designed for wet locations.
R Never touch uninsulated telephone wires or
terminals unless the telephone line has
been disconnected at the network interface.
R Use caution when installing or modifying
telephone lines.
R The AC adaptor is used as the main
disconnect device. Ensure that the AC
outlet is installed near the product and is
easily accessible.
R This product is unable to make calls when:
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p7
7
2011/11/21
12:02:12
7
Important Information
– the handset batteries need recharging or
have failed.
– there is a power failure.
Battery
R We recommend using the batteries noted
on page 5. USE ONLY rechargeable
Ni-MH batteries AAA (R03) size.
R Do not mix old and new batteries.
R Do not open or mutilate the batteries.
Released electrolyte from the batteries is
corrosive and may cause burns or injury to
the eyes or skin. The electrolyte is toxic and
may be harmful if swallowed.
R Exercise care when handling the batteries.
Do not allow conductive materials such as
rings, bracelets, or keys to touch the
batteries, otherwise a short circuit may
cause the batteries and/or the conductive
material to overheat and cause burns.
R Charge the batteries provided with or
identified for use with this product only, in
accordance with the instructions and
limitations specified in this manual.
R Only use a compatible base unit (or
charger) to charge the batteries. Do not
tamper with the base unit (or charger).
Failure to follow these instructions may
cause the batteries to swell or explode.
Attention:
A nickel metal hydride battery that is
recyclable powers the product you have
purchased.
Please call 1-800-8-BATTERY
(1-800-822-8837) for information on how to
recycle this battery.
8
Important safety
instructions
When using your product, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock, and
injury to persons, including the following:
1. Do not use this product near water for
example, near a bathtub, washbowl,
kitchen sink, or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric
shock from lightning.
3. Do not use the telephone to report a gas
leak in the vicinity of the leak.
4. Use only the power cord and batteries
indicated in this manual. Do not dispose of
batteries in a fire. They may explode.
Check with local codes for possible special
disposal instructions.
SAVE THESE INSTRUCTIONS
For best performance
Base unit location/avoiding noise
The base unit and other compatible Panasonic
units use radio waves to communicate with
each other.
R For maximum coverage and noise-free
communications, place your base unit:
– at a convenient, high, and central
location with no obstructions between
the handset and base unit in an indoor
environment.
– away from electronic appliances such as
TVs, radios, personal computers,
wireless devices, or other phones.
– facing away from radio frequency
transmitters, such as external antennas
of mobile phone cell stations. (Avoid
putting the base unit on a bay window or
near a window.)
R Coverage and voice quality depends on the
local environmental conditions.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p8
8
2011/11/21
12:02:12
Important Information
R If the reception for a base unit location is
not satisfactory, move the base unit to
another location for better reception.
Environment
R Keep the product away from electrical noise
generating devices, such as fluorescent
lamps and motors.
R The product should be kept free from
excessive smoke, dust, high temperature,
and vibration.
R The product should not be exposed to
direct sunlight.
R Do not place heavy objects on top of the
product.
R When you leave the product unused for a
long period of time, unplug the product from
the power outlet.
R The product should be kept away from heat
sources such as heaters, kitchen stoves,
etc. It should not be placed in rooms where
the temperature is less than 0 °C (32 °F) or
greater than 40 °C (104 °F). Damp
basements should also be avoided.
R The maximum calling distance may be
shortened when the product is used in the
following places: Near obstacles such as
hills, tunnels, underground, near metal
objects such as wire fences, etc.
R Operating the product near electrical
appliances may cause interference. Move
away from the electrical appliances.
Notice for product disposal, transfer,
or return
R This product can store your private/
confidential information. To protect your
privacy/confidentiality, we recommend that
you erase information such as phonebook
or caller list entries from the memory before
you dispose of, transfer, or return the
product.
Notice
Routine care
R Wipe the outer surface of the product
with a soft moist cloth.
R Do not use benzine, thinner, or any
abrasive powder.
Other information
ENERGY STAR
As an ENERGY STAR® Partner, Panasonic
has determined that this product meets the
ENERGY STAR guidelines for energy
efficiency. ENERGY STAR is a U.S.
registered mark.
CAUTION: Risk of explosion if battery is
replaced by an incorrect type. Dispose of used
batteries according to the instructions.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p9
9
2011/11/21
12:02:12
9
Important Information
Specifications
R Standard:
DECT 6.0 (Digital Enhanced Cordless
Telecommunications 6.0)
Bluetooth wireless technology 2.0
R Frequency range:
1.92 GHz to 1.93 GHz (DECT)
2.402 GHz to 2.48 GHz (Bluetooth)
R RF transmission power:
115 mW (max.)
R Power source:
120 V AC, 60 Hz
R Power consumption:
Base unit:
Standby: Approx. 1.2 W
Maximum: Approx. 4.5 W
Charger:
Standby: Approx. 0.1 W
Maximum: Approx. 2.0 W
R Operating conditions:
0 °C – 40 °C (32 °F – 104 °F), 20 % – 80 %
relative air humidity (dry)
Note:
R Design and specifications are subject to
change without notice.
R The illustrations in these instructions may
vary slightly from the actual product.
10
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p10
10
2011/11/21
12:02:12
Getting Started
n Charger
Setting up
Connections
R Use only the supplied Panasonic AC
adaptor PNLV226.
R If you do not connect the telephone line
cord and use only cellular lines, set the
cellular line only mode to use this unit more
conveniently (page 20).
Hooks
To power outlet
n Base unit
Press plug firmly.
“Click”
Battery installation
R USE ONLY Ni-MH batteries AAA (R03)
size.
R Do NOT use Alkaline/Manganese/Ni-Cd
batteries.
).
R Confirm correct polarities ( ,
Hook
To power outlet
“Click”
To single-line
telephone jack
(RJ11C)
Correct
DSL/ADSL filter*
Rechargeable Ni-MH ONLY
Incorrect
*DSL/ADSL filter (not supplied) is required if
you have DSL/ADSL service.
R When the date and time setting is
displayed, see page 17.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p11
11
2011/11/21
12:02:12
11
Getting Started
Battery charging
Charge for about 7 hours.
R When the batteries are fully charged,
“Fully charged” is displayed.
Confirm “Charging” is displayed.
R Avoid touching the battery ends (
the unit contacts.
,
) or
Note for battery charging
R It is normal for the handset to feel warm
during charging.
R Clean the charge contacts of the handset,
base unit, and charger with a soft and dry
cloth once a month. Before cleaning the
unit, disconnect from power outlets and any
telephone line cords. Clean more often if
the unit is exposed to grease, dust, or high
humidity.
Battery level
Icon
Battery level
High
Medium
Low
Note when setting up
Needs charging.
Note for connections
R The AC adaptor must remain connected at
all times. (It is normal for the adaptor to feel
warm during use.)
R The AC adaptor should be connected to a
vertically oriented or floor-mounted AC
outlet. Do not connect the AC adaptor to a
ceiling-mounted AC outlet, as the weight of
the adaptor may cause it to become
disconnected.
Empty
Panasonic Ni-MH battery
performance (supplied batteries)
Operation
Operating time
In continuous use
13 hours max.*1
Not in use (standby)
11 days max.*1
During a power failure
*1
R The unit will not work during a power
failure. We recommend connecting a
corded-type telephone (without AC adaptor)
to the same telephone line or to the same
telephone line jack using a Panasonic
T-adaptor (page 5).
Note:
R Actual battery performance depends on
usage and ambient environment.
R Even after the batteries are fully charged,
the handset can be left on the base unit or
charger without any ill effect on the
batteries.
R The battery level may not be displayed
correctly after you replace the batteries. In
this case, place the handset on the base
unit or charger and let it charge for at least
7 hours.
Note for battery installation
R Use the supplied rechargeable batteries.
For replacement, we recommend using the
Panasonic rechargeable batteries noted on
page 5, 8.
) with a dry
R Wipe the battery ends ( ,
cloth.
12
If Eco mode is on.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p12
12
2011/11/21
12:02:12
Getting Started
Intelligent eco mode
This feature automatically reduces handset
power consumption by suppressing handset
transmission power when the handset is close
to the base unit.
is
R When this feature is activated,
displayed. However, during a cellular call,
is not displayed even though this
feature is activated.
R Eco mode is turned off when the clarity
booster is activated (page 24).
Controls
Base unit
n KX-TG7731 series (page 3)
A
B
C
D
E
F G H I J
K
L
Charge contacts
Speaker
HEADSET indicator
Message counter
MERASEN
CELL 1 indicator
CELL 2 indicator
MnN (STOP)
MjN/MkN (VOL.: Volume up/down)
M
N/M
N (Repeat/Skip)
M N (PLAY)
Message indicator
MLOCATORN
MANSWER ON/OFFN
ANSWER ON/OFF indicator
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p13
13
2011/11/21
12:02:12
13
Getting Started
n KX-TG7741 series (page 3)
G
C
H
Dial keypad (*: TONE)
D
I
Microphone
J
E
K
F
A
MCELL 2N
CELL 2 indicator
Message counter
Handset
A
L
B
M N O
H
P
I
B
C
J
D
K
E
Q
R
Charge contacts
F
Speaker
MHOLDN MCONFN (Conference)
G
MREDIALN MPAUSEN
MFLASHN MCALL WAITN
L
MSP-PHONEN (Speakerphone)
M
SP-PHONE indicator
MERASEN MMUTEN
A
MANSWER ON/OFFN
ANSWER ON/OFF indicator
MLOCATORN MINTERCOMN
B
MnN (STOP)
M N (PLAY)
Message indicator
MjN/MkN (VOL.: Volume up/down)
M
N/M
N (Repeat/Skip)
MjN/MkN (VOL.: Volume up/down)
MHEADSETN
HEADSET indicator
MCELL 1N
CELL 1 indicator
14
Ringer indicator
Message indicator
Speaker
M N (SP-PHONE: Speakerphone)
M
N (TALK)
Headset jack
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p14
14
2011/11/21
12:02:12
Getting Started
Dial keypad (*: TONE)
Display/Indicators
Receiver
Display
Handset display items
MCALL WAITN MFLASHN
Item
MOFFN
Meaning
Microphone
Within base unit range
Charge contacts
Out of base unit range
n Control type
Soft keys
The handset features 3 soft keys. By
pressing a soft key, you can select the
feature shown directly above it on the
display.
Navigator key
– MDN, MCN, MFN, or MEN: Scroll through
various lists and items.
(Volume: MDN or MCN): Adjust the
–
receiver or speaker volume while
talking.
– MFN CID (Caller ID): View the caller list.
– MEN REDIAL: View the redial list.
Belt clip
n To attach
n To remove
The landline is in use.
R When flashing:
The call is put on hold.
R When flashing rapidly: An
incoming call is now being
received.
A cellular line is in use.
R When flashing:
The cellular call is put on
hold.
R When flashing rapidly:
A cellular call is being
received.
1
A cellular phone is
connected.*1 Ready to make/
receive cellular calls.
R When turned off:
A cellular phone is not
connected to the base unit
(page 20).
– The cellular line is selected
for the ringer setting.
– A cellular call is being
received on that line.
Eco mode is on.*2 (page 13)
Equalizer is set. (page 24)
Speakerphone is on.
(page 22)
Ringer volume is off.*3
(page 35, 37)
Silent mode is on. (page 40)
Call sharing mode is off.
(page 38)
Alarm is on. (page 40)
Handset number
Battery level
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p15
15
2011/11/21
12:02:12
15
Getting Started
Item
Meaning
Status
Meaning
Blocked call (page 41)
Green
(Flashing
rapidly)
A cellular call is being
received.
Amber
(On)
A cellular phone is not
connected to the base unit
(page 20).
Amber
(Flashing
rapidly)
The base unit is searching for
the registered cellular phone.
Red
(Flashing)
– The base unit is registering
a cellular phone.
– A cellular call is put on hold.
Light off
A cellular phone is not
registered to the base unit.
Clarity booster is on.*2
(page 24)
In use
Answering system is being
used by another handset or
the base unit.
Cell1 in
use
Someone is using the cellular
line.
Cell2 in
use
Line in
use
*1
*2
*3
Someone is using the landline.
Corresponding cellular line(s) is indicated
next to the item.
During a cellular call, the item is not
displayed even though the feature is
activated.
Corresponding lines (1, 2: cellular line, L:
landline) are indicated next to the item. If
all lines are turned off, no line is indicated.
Base unit display item
Item
Meaning
“Greeting only” is selected
as the caller’s recording time.
In this case, the answering
system answers calls with a
greeting message and caller
messages are not recorded.
(page 53)
CELL 1/CELL 2 indicators on the
base unit
The CELL 1/CELL 2 indicators show each
cellular line status.
Status
Meaning
Green
(On)
A cellular phone is connected.
Ready to make/receive
cellular calls.
Green
(Flashing)
– The cellular line is in use.
– Phonebook entries are
being copied from a
cellular phone (page 46).
16
HEADSET indicator on the base unit
The HEADSET indicator shows the Bluetooth
headset status.
Status
Meaning
Green
(On)
A Bluetooth headset is
connected to the base unit.
Ready to use it.
Green
(Flashing)
A Bluetooth headset is in use.
Green
(Flashing
rapidly)
A landline call is being
received.
Amber
(On)
The Bluetooth headset is not
connected to the base unit.
Amber
(Flashing
rapidly)
The base unit is searching for
the registered Bluetooth
headset.
Red
(Flashing)
– The base unit is registering
a headset.
– Mute is turned on.
Light off
A Bluetooth headset is not
registered to the base unit.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p16
16
2011/11/21
12:02:12
Getting Started
Display language
Initial settings
n Direct command code:
Programmable settings can be accessed
by pressing MMENUN, # and then the
corresponding code on the dial keypad
(page 33).
Example: Press MMENUN#101.
Symbol
Meaning
Example:
MbN: “Off”
Press MCN or MDN to select
the words in quotations.
Date and time
Important:
R When you install the batteries for the first
time, the handset may prompt you to set
date and time. First press MSELECTN, then
proceed to step 2.
3
4
5
6
1
2
3
n Symbol meaning:
1
2
You can select either “English” or
“Español” as the display language. The
default setting is “English”.
MMENUN#101
Enter the current month, date, and year
by selecting 2 digits for each.
Example: July 15, 2012
07 15 12
MOKN
Enter the current hour and minute
(12-hour clock format) by selecting 2
digits for each.
Example: 9:30
09 30
MMENUN#110
MbN: Select the desired setting. a
MSAVEN
MOFFN
Voice guidance language
You can select either “English” or
“Español” as the voice guidance language
of the answering system. The default setting is
“English”.
1
2
3
MMENUN#112
MbN: Select the desired setting. a
MSAVEN
MOFFN
Dialing mode
If you cannot make calls, change this setting
according to your telephone line service. The
default setting is “Tone”.
“Tone”: For tone dial service.
“Pulse”: For rotary/pulse dial service.
1
2
3
MMENUN#120
MbN: Select the desired setting.
MSAVEN a MOFFN
MAM/PMN: Select “AM” or “PM”.
MSAVEN a MOFFN
Note:
R When English is selected as the display
language, 12-hour clock format is used.
When Spanish is selected, 24-hour clock
format is used.
R The date and time may be incorrect after a
power failure. In this case, set the date and
time again.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p17
17
2011/11/21
12:02:12
17
Link to Cell
Link to cell feature
To use this feature, you must first register and
connect your cellular phones to the base unit
(page 18).
Your cellular phones must have Bluetooth
wireless technology that is compatible with this
product.
This feature allows you to:
– make or answer cellular calls using your
home phone (handset or base unit) with
better reception.
– maximize the benefits of cellular services
(such as free night and weekend calls, or
cellular to cellular call plans) by utilizing
unused peak minutes with your home
phone.
– conserve the battery power of your cellular
phone while the unit is on a cellular call.
(We recommend charging your cellular
phone during the cellular call as your
cellular phone battery is being consumed.)
Important:
R Up to 2 cellular phones can be registered.
However, only one Bluetooth device
(cellular phone or headset) can be
connected to the base unit at a time.
R Locate your cellular phone near the base
unit. If the cellular phone is too close to the
base unit during a cellular call, you may
hear noise. For best performance, we
recommend placing the cellular phone
between 0.6 m to 3 m (2 feet to 10 feet)
away from the base unit.
Trademarks
R The Bluetooth® word mark and logos are
owned by the Bluetooth SIG, Inc. and any
use of such marks by Panasonic
Corporation is under license. All other
trademarks identified herein are the
property of their respective owners.
Registering a cellular
phone
http://www.panasonic.com/link2cell
R Before registering a Bluetooth enabled
cellular phone to the base unit:
– we recommend you change the PIN
(page 21).
– make sure that no Bluetooth device such
as a Bluetooth headset is connected to
your cellular phone.
1
Handset:
MMENUN
For CELL 1: #6241
For CELL 2: #6242
R After the CELL 1 or CELL 2 indicator
on the base unit starts flashing red, the
rest of the procedure must be
completed within 5 minutes.
2
Your cellular phone:
While the CELL 1 or CELL 2 indicator is
flashing red, follow the instructions of your
cellular phone to enter the registration
mode.
R Depending on your cellular phone, it
may ask you to enter the base unit PIN
(default: “0000”).
3
Handset:
Wait until a long beep sounds.
R It may take more than 10 seconds to
complete registration.
R When the CELL 1 or CELL 2 indicator
lights green, the cellular phone is
connected to the base unit. You are
ready to make cellular calls.
4
To select which unit receives calls for the
cellular line, press MOKN then continue
from step 3, “Selecting which unit
receives cellular calls”, page 19.
R If not required, go to step 5.
5
MOFFN
Note:
R Make sure that your cellular phone is set to
connect to this product automatically. Refer
to your cellular phone’s operating
instructions.
R Make sure you cancel your cellular phone’s
current registration if you want to register it
to the other line (page 21).
Important:
R For more details and the list of compatible
cellular phones, please visit our Web site:
18
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p18
18
2011/11/21
12:02:12
Link to Cell
Link to cell settings
Selecting which unit receives
cellular calls
You can select which unit rings and receives
calls for a cellular line. When “All” is
selected, all handsets and the base unit ring.
1
2
3
4
MMENUN
For CELL 1: #6271
For CELL 2: #6272
MbN: Select the desired handset or “All”.
MSAVEN a MOFFN
Note:
R When you select a specific handset to
receive calls for a cellular line:
– other handsets cannot answer the calls.
– the base unit can answer the calls even
though it does not ring. However, you
can make the base unit ring by adjusting
the base unit ringer volume (page 35).
(KX-TG7741 series: page 3)
R When you change the setting to “All”, the
base unit ringer volume also returns to the
lowest level even if the ringer volume has
been changed.
Ring as cell mode
Once this feature is turned on, the handset
and base unit ring using the same ringer tone
as your cellular phone.
The following settings are available:
– “Off”: Turn this feature off to use the
ringer tones of the handset and base unit.
Caller information is announced depending
on the Talking Caller ID setting (page 37).
– “On (with Talking CID)”
(default): The handset and base unit use
your cellular phone’s ringer tone. Caller
information is announced even if the
Talking Caller ID is turned off.
– “On (without Talking CID)”: The
handset and base unit use your cellular
phone’s ringer tone. Caller information is
not announced even if the Talking Caller ID
is turned on.
Important:
R To use this feature, your cellular phone
must support Bluetooth in-band ringtone.
Refer to your cellular phone’s operating
instructions.
1
2
3
4
MMENUN
For CELL 1: #6141
For CELL 2: #6142
MbN: Select the desired setting.
MSAVEN a MOFFN
Note:
R The units use the preset ringer tones
(page 37) instead of your cellular phone’s
ringer tone when a cellular call is being
received if:
– your cellular phone is in silent mode
(depending on your cellular phone).
– the base unit is in use.
– 2 handsets are sharing a landline call.
R If your cellular phone is in silent mode with
“On (with Talking CID)” set, the unit
announces caller information even when
Talking Caller ID is turned off (page 37).
To use the handset ringer tone
instead of your cellular phone’s
ringer tone
Select “Off” in step 3, “Ring as cell mode”,
page 19.
To change the handset ringer tone for a
cellular line, see page 35.
Auto connection to the cellular
phone
After registration, your cellular phone is
connected to the base unit. If you move the
cellular phone out of base unit range, the
cellular phone is disconnected from the base
unit. This feature allows the base unit to try to
reconnect the cellular phone at regular
intervals when it returns within base unit
range. You can set the interval. The default
setting is “1 min”.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p19
19
2011/11/21
12:02:12
19
Link to Cell
Important:
R When you are using a cellular line or a
Bluetooth headset, the base unit loses its
connection from other Bluetooth devices
(cellular phone or headset). To
automatically resume the connection to
cellular phones, leave the auto connection
on.
R Some cellular phones lose connection after
usage, please check the specification of
your cellular phone for more details.
1
2
3
MMENUN#632
MbN: Select the desired setting.
MSAVEN a MOFFN
Note:
R Some cellular phone may ask you if you
accept the connection requirement from the
base unit. In that case, select “Off” in step
2. Check the specification of your cellular
phone.
Connecting/disconnecting the
cellular phone manually
When you make or answer calls with your
cellular phone, we recommend disconnecting
it from the base unit, otherwise received audio
may not be heard on your cellular phone.
You can also manually reconnect the cellular
phone to the base unit without waiting for the
auto connection feature to resume the
connection.
1
2
3
MMENUN
Note:
R Once you set this mode, you can use the
following buttons to make cellular calls:
– for the handset, press M
N or M N
instead of MCELLN (page 22).
– for the base unit, press MSP-PHONEN
instead of the line button (MCELL 1N or
MCELL 2N) set for the cellular line
selection (page 20, 27).
(KX-TG7741 series: page 3)
R Once you set this mode, the following
features cannot be used:
– Landline features (page 38)
– Answering system (page 49)
Messages cannot be received.
– Voice mail features (page 55)
R After this mode is turned on or off, the base
unit reboots.
– Bluetooth connections from cellular
phones or headset are disconnected. If
the auto connection is turned on
(page 19), the cellular phones are
reconnected.
–
will be displayed on the handset
momentarily. The handset can be used
is displayed.
once
When you use the landline again
Cellular line selection
MOFFN
If you do not use the landline, we recommend
setting the unit to the cellular line only mode.
20
To turn on:
MbN: “On” a MSELECTN a
MbN: “Yes” a MSELECTN
To turn off:
MbN: “Off” a MSELECTN
Before connecting the telephone line to the
base unit, select “Off” in step 2, “Cellular line
only mode (If you do not use the landline)”,
page 20.
To connect/disconnect:
For CELL 1: #6251
For CELL 2: #6252
R A long beep sounds.
Cellular line only mode (If you do
not use the landline)
1
2
MMENUN#157
This feature determines which cellular line is
selected to make cellular calls when:
– you press MCELLN on the handset.
– you press M
N or M N on the handset
while the cellular line only mode is turned
on.
– you press MSP-PHONEN on the base unit
while the cellular line only mode is turned
on. (KX-TG7741 series: page 3)
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p20
20
2011/11/21
12:02:13
Link to Cell
The following settings are available:
– “Manual” (handset only: default): You can
select the desired cellular line when making
a call.
– “Cellular phone 1” (base unit default): CELL
1 is selected.
– “Cellular phone 2”: CELL 2 is selected.
1
2
3
4
*1
4
MOFFN
Changing the PIN for the second time
MMENUN
Follow step 1, “Changing the Bluetooth PIN
(Personal Identification Number)”, page 21.
Enter the current 4-digit PIN, then continue
from step 2.
For handset: #634
For base unit*1: #*634
Deregistering Bluetooth devices
MbN: Select the desired setting.
MSAVEN a MOFFN
KX-TG7741 series: page 3
Storing your area code (for
dialing only a 7-digit phone
number to make a local call)
A handset can cancel the registration of
another Bluetooth device (cellular phone or
headset) that is stored to the base unit.
1
2
MMENUN#134
MbN: Select the desired device. a
MSELECTN
indicates a cellular phone, and
R
indicates a headset.
You need to add your area code when making
cellular calls to a phone number in your area.
Once you store your area code, it is
automatically added to the beginning of the
7-digit phone number when making cellular
calls.
3
1
2
MbN: “Yes” a MSELECTN
R When the cellular phone is
deregistered, the CELL 1 or CELL 2
indicator is turned off.
R When the headset is deregistered, the
HEADSET indicator is turned off.
4
MOFFN
3
MMENUN#633
Enter the 3-digit area code.
R To correct a digit, press MCLEARN.
MSAVEN a MOFFN
Changing the Bluetooth PIN
(Personal Identification Number)
The PIN is used to register cellular phones to
the base unit. The default PIN is “0000”. To
prevent unauthorized access to this product,
we recommend that you change the PIN, and
keep it confidential.
Important:
R Please make note of your new PIN. The
unit does not reveal the PIN to you. If you
forget your PIN, see page 68.
1
2
3
MMENUN#619
Enter the new 4-digit PIN. a MOKN
Enter the new 4-digit PIN again. a
MSAVEN
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p21
21
2011/11/21
12:02:13
21
Making/Answering Calls Using the Handset
Making cellular calls
Important:
R Only 1 cellular line can be used at a time.
R Before making calls, confirm that the CELL
1 or CELL 2 indicator lights green (page 16).
1
Lift the handset and dial the phone
number.
R To correct a digit, press MCLEARN.
2
MCELLN
R The unit starts dialing when:
– only 1 cellular phone is registered.
– a specific line is set to make cellular
calls (page 20).
Go to step 4.
3
MbN: Select the desired cellular phone. a
MSELECTN
4
Erasing a number in the redial list
1
2
3
4
R To switch to the speaker, press M N.
To switch back to the receiver, press M N/
M
N.
Adjusting the receiver or speaker
volume
Press MjN or MkN repeatedly while talking.
Note:
R There are 5 volume levels (1 to 5) for the
receiver. When you change the receiver
volume to level 5 (maximum level), the
volume returns to level 4 (default) after you
hang up.
Making a cellular call using the redial
list
The last 5 phone numbers dialed are stored in
the redial list (each 48 digits max.).
1
2
3
22
MEN REDIAL
MbN: Select the desired phone number.
MCELLN
R The unit starts dialing when:
– only 1 cellular phone is registered.
M N REDIAL
MbN: Select the desired phone number.
a MERASEN
MbN: “Yes” a MSELECTN
MOFFN
Making landline calls
1
Lift the handset and dial the phone
number.
R To correct a digit, press MCLEARN.
2
3
M
4
When you finish talking, press MOFFN or
place the handset on the base unit or
charger.
Note:
– a specific line is set to make cellular
calls (page 20).
MbN: Select the desired cellular phone. a
MSELECTN
N
When you finish talking, press MOFFN or
place the handset on the base unit or
charger.
Using the speakerphone
1
Dial the phone number and press M N.
R Speak alternately with the other party.
2
When you finish talking, press MOFFN.
Note:
R For best performance, use the
speakerphone in a quiet environment.
R To switch back to the receiver, press M N/
M
N.
Making a call using the redial list
1
2
3
MEN REDIAL
MbN: Select the desired phone number.
M
N
Pause (for PBX/long distance service
users)
A pause is sometimes required when making
calls using a PBX or long distance service.
When storing a calling card access number
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p22
22
2011/11/21
12:02:13
Making/Answering Calls Using the Handset
and/or PIN in the phonebook, a pause is also
needed (page 32).
Example: If you need to dial the line access
number “9” when making outside calls with a
PBX:
1
2
9 a MPAUSEN
Dial the phone number. a M
N
Note:
R A 3.5 second pause is inserted each time
MPAUSEN is pressed.
2
3
MbN: Select the desired volume.
MSAVEN a MOFFN
Temporary handset ringer off
While the handset is ringing for a call, you can
turn the ringer off temporarily by pressing M N.
Useful features during a
call
Answering calls
Hold
When a call is being received, the ringer
indicator flashes rapidly.
This feature allows you to put an outside call
on hold.
1
1
2
3
2
Lift the handset and press M
N or M N
when the unit rings.
R To answer a cellular call, you can also
press MCELLN.
R You can also answer the call by
pressing any dial key from 0 to 9,
*, or #. (Any key answer feature)
When you finish talking, press MOFFN or
place the handset on the base unit or
charger.
Auto talk
You can answer calls simply by lifting the
handset off the base unit or charger. You do
N. To turn this feature
not need to press M
on, see page 38.
Adjusting the handset ringer volume
n While the handset is ringing for an
incoming call:
Press MjN or MkN repeatedly to select the
desired volume.
n Programming the volume beforehand:
1 To change the cellular line ringer
volume:
For CELL 1: MMENUN#6281
For CELL 2: MMENUN#6282
To change the landline ringer
volume:
MMENUN#160
Press MMENUN during an outside call.
MbN: “Hold” a MSELECTN
To release hold on the cellular line:
Press MCELLN.
R Another handset user can take the call:
MCELLN*1 a MSELECTN
*1 The call is taken when:
– only 1 cellular phone is
registered.
– the line is set to make cellular
calls (page 20).
R The base unit user can take the call by
pressing MCELL 1N or MCELL 2N.
(KX-TG7741 series: page 3)
To release hold on the landline:
Press M
N.
R Another handset user can take the call
N.
by pressing M
R The base unit user can take the call by
pressing MSP-PHONEN.
(KX-TG7741 series: page 3)
Note:
R If a call is kept on hold for more than 9
minutes, an alarm tone starts to sound and
the ringer indicator flashes rapidly. After 1
additional minute on hold, the call is
disconnected.
R If another phone is connected to the same
line, you can also take the call by lifting its
handset.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p23
23
2011/11/21
12:02:13
23
Making/Answering Calls Using the Handset
Mute
While mute is turned on, you can hear the
other party, but the other party cannot hear
you.
1
Press MMUTEN during conversation.
R MMUTEN flashes.
2
To return to the conversation, press
MMUTEN again.
Note:
R MMUTEN is a soft key visible on the handset
display during a call.
Flash for landline calls
MFLASHN allows you to use the special
features of your host PBX such as transferring
an extension call, or accessing optional
telephone services.
Note:
R To change the flash time, see page 38.
For call waiting or Call Waiting
Caller ID service users
To use call waiting or Call Waiting Caller ID,
you must first subscribe with your service
provider/telephone company.
This feature allows you to receive calls while
you are already talking on the phone. If you
receive a call while on the phone, you will hear
a call waiting tone.
If you subscribe to both Caller ID and Call
Waiting with Caller ID services, the 2nd
caller’s information is displayed after you hear
the call waiting tone on the handset.
1
Press MCALL WAITN to answer the 2nd
call.
2
To switch between calls, press MCALL
WAITN.
Note:
R Please contact your service provider/
telephone company for details and
availability of this service in your area.
Temporary tone dialing for
landline calls (for rotary/pulse
service users)
You can temporarily switch the dialing mode
to tone when you need to access touch-tone
services (for example, answering services,
telephone banking services, etc.).
Press * (TONE) before entering access
numbers which require tone dialing.
Handset clarity booster
This feature can improve sound clarity when
the handset is used in an area where there
may be interference. During an outside call,
this feature is turned on automatically when
necessary.
is
R When this feature is turned on,
displayed. However, during a cellular call,
is not displayed even though the
feature is activated.
Handset equalizer
This feature clarifies the voice of the person
you are talking to, producing a more
natural-sounding voice that is easier to hear
and understand.
1
2
3
4
Press MMENUN while talking.
MbN: “Equalizer” a MSELECTN
MbN: Select the desired setting.
Press MOKN to exit.
Note:
R When this feature is activated,
is
displayed while talking.
R Depending on the condition and quality of
your telephone line, this feature may
emphasize existing line noise. If it becomes
difficult to hear, turn this feature off.
R This feature is not available while using the
speakerphone.
Call share
You can join an existing outside call.
24
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p24
24
2011/11/21
12:02:13
Making/Answering Calls Using the Handset
n While another unit is on a cellular call:
1 To join the conversation, press
MCELLN.
R You can join the conversation
when:
– only 1 cellular phone is
registered.
– the line is set to make cellular
calls (page 20).
2
During a conversation using a cellular
phone, press MCELLN.
R The call is transferred to the handset
when:
– only 1 cellular phone is registered.
– the line is set to make cellular calls
(page 20).
2
MbN: Select the desired cellular phone. a
MSELECTN
R The call is transferred to the handset.
MbN: Select the desired cellular phone.
a MSELECTN
n While another unit is on a landline call:
N.
To join the conversation, press M
Note:
R A maximum of 3 parties (including 1 outside
party) can join a conversation using 2
extensions. (3-way conference)
R To prevent other users from joining your
conversations with outside callers, turn call
sharing mode off (page 38).
Transferring a cellular call
between the handset and a
cellular phone
Transferring a cellular call from the
handset to a cellular phone
1
2
1
Using the other line during a
conversation
You can handle a cellular call and a landline
call at the same time. When another call is
being received during a conversation, the
interrupt tone sounds (page 37), and the 2nd
caller’s information is displayed if you
subscribe to Caller ID (page 43). You can
answer the 2nd call while holding the 1st call.
Making/answering a cellular call
during a conversation on the landline
1
2
3
Press MMENUN during a cellular call.
MbN: “Transfer to cell” a
MSELECTN
R The cellular call is transferred to the
cellular phone.
Note:
R Depending on your cellular phone type, you
may need to set the cellular phone to be
ready to talk before transferring. For
example, if your cellular phone has a top
cover, open it beforehand.
To make a 2nd call:
Dial the phone number. a MCELLN*1 a
MbN: Select the desired cellular phone. a
MSELECTN
*1 The unit starts dialing when:
– only 1 cellular phone is registered.
– a specific line is set to make
cellular calls (page 20).
To answer a 2nd call:
MCELLN
R To hold the 2nd call: MMENUN a MbN:
“Hold” a MSELECTN
4
Transferring a cellular call from a
cellular phone to the handset
During a conversation using a cellular phone,
the call cannot be transferred to the handset
by the cellular phone. Perform the following
with the handset.
Press MMENUN during a landline call.
MbN: “Hold” a MSELECTN
To hang up the 2nd call and return to the
1st call (landline call), press MOFFN, then
N.
press M
Making/answering a landline call
during a conversation on a cellular line
1
Press MMENUN during a cellular call.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p25
25
2011/11/21
12:02:13
25
Making/Answering Calls Using the Handset
2
3
4
26
MbN: “Hold” a MSELECTN
To make a 2nd call:
Dial the phone number. a M
N
To answer a 2nd call:
M
N
R To hold the 2nd call: MMENUN a MbN:
“Hold” a MSELECTN
To hang up the 2nd call and return to the
1st call (cellular call), press MOFFN, then
press MCELLN.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p26
26
2011/11/21
12:02:13
Making/Answering Calls Using the Base Unit
Making cellular calls
Available for:
KX-TG7741 series (page 3)
1
2
3
Press MCELL 1N or MCELL 2N.
Dial the phone number.
When the other party answers, speak into
the microphone.
R Speak alternately with the other party.
4
When you finish talking, press
MSP-PHONEN.
Note:
R For best performance, use the
speakerphone in a quiet environment.
R While on a call, you can switch from the
base unit to the handset:
With the call sharing mode on (page 29),
press MCELLN on the handset. a MbN:
Select the desired cellular phone. a
MSELECTN a Press MSP-PHONEN on the
base unit.
– When only 1 cellular phone is registered
or the line is set to make cellular calls
(page 20), press MCELLN on the
handset, then press MSP-PHONEN on
the base unit.
If the handset is on the base unit, simply lift
it.
Adjusting the speaker volume
4
When you finish talking, press
MSP-PHONEN.
Note:
R While on a call, you can switch from the
base unit to the handset:
Press M
N on the handset, then press
MSP-PHONEN on the base unit with the call
sharing mode on (page 29).
If the handset is on the base unit, simply lift
it.
Redialing the last number dialed
MSP-PHONEN a MREDIALN
Pause (for PBX/long distance service
users)
A pause is sometimes required when making
calls using a PBX or long distance service.
When storing a calling card access number
and/or PIN in the phonebook, a pause is also
needed (page 32).
Example: If you need to dial the line access
number “9” when making outside calls with a
PBX:
1
2
3
MSP-PHONEN
9 a MPAUSEN
Dial the phone number.
Note:
R A 3.5 second pause is inserted each time
MPAUSEN is pressed.
Press MjN or MkN repeatedly while talking.
Redialing the last number dialed
Answering calls
1
2
When a call is being received, the SP-PHONE
indicator flashes rapidly.
When a cellular call is being received, the
CELL 1 or CELL 2 indicator and SP-PHONE
indicator flash rapidly.
Press MCELL 1N or MCELL 2N.
MREDIALN
Making landline calls
1
1
2
3
Press MSP-PHONEN when the unit rings.
R You can also answer the cellular call
by pressing MCELL 1N or MCELL 2N.
2
3
Speak into the microphone.
MSP-PHONEN
Dial the phone number.
When the other party answers, speak into
the microphone.
When you finish talking, press
MSP-PHONEN.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p27
27
2011/11/21
12:02:13
27
Making/Answering Calls Using the Base Unit
Adjusting the base unit ringer volume
n While the base unit is ringing for an
incoming call:
Press MjN or MkN repeatedly to select the
desired volume.
R To turn the ringer off, press and hold
MkN until the unit beeps.
n Programming the volume beforehand:
1 To change the cellular line ringer
volume:
For CELL 1: MMENUN#*6281
For CELL 2: MMENUN#*6282
To change the landline ringer
volume:
MMENUN#*160
2
3
MbN: Select the desired volume.
R If a call is kept on hold for more than 9
minutes, an alarm tone starts to sound.
After 1 additional minute on hold, the call is
disconnected.
R If another phone is connected to the same
line, you can also take the call by lifting its
handset.
Mute
While mute is turned on, you can hear the
other party, but the other party cannot hear
you.
1
Press MMUTEN during conversation.
R The SP-PHONE indicator on the base
unit flashes.
2
To return to the conversation, press
MMUTEN again.
MSAVEN a MOFFN
Flash for landline calls
Useful features during a
call
Hold
This feature allows you to put an outside call
on hold.
1
2
Press MHOLDN during an outside call.
For call waiting service users
To release hold on the cellular line:
Press MCELL 1N or MCELL 2N.
R A handset user can take the call:
MCELLN*1 a MSELECTN
*1 The call is taken when:
– only 1 cellular phone is
registered.
– the line is set to make cellular
calls (page 20).
To release hold on the landline:
Press MSP-PHONEN.
R A handset user can take the landline
N.
call by pressing M
To use call waiting, you must first subscribe
with your service provider/telephone company.
This feature allows you to receive calls while
you are already talking on the phone. If you
receive a call while on the phone, you will hear
a call waiting tone.
Note:
R While a cellular line is on hold, the CELL 1
or CELL 2 indicator flashes red. While a
landline call is on hold, the SP-PHONE
indicator flashes.
28
MFLASHN allows you to use the special
features of your host PBX such as transferring
an extension call, or accessing optional
telephone services.
Note:
R To change the flash time, see page 38.
1
Press MCALL WAITN to answer the 2nd
call.
2
To switch between calls, press MCALL
WAITN.
Note:
R Please contact your service provider/
telephone company for details and
availability of this service in your area.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p28
28
2011/11/21
12:02:13
Making/Answering Calls Using the Base Unit
Temporary tone dialing for
landline calls (for rotary/pulse
service users)
You can temporarily switch the dialing mode
to tone when you need to access touch-tone
services (for example, answering services,
telephone banking services, etc.).
Press * (TONE) before entering access
numbers which require tone dialing.
Call share
You can join an existing outside call.
To select the line that is being used for the call:
– for a cellular line press MCELL 1N or MCELL
2N.
– for the landline press MSP-PHONEN.
Note:
R A maximum of 3 parties (including 1 outside
party) can join a conversation using 2
extensions. (3-way conference)
R To prevent other users from joining your
conversations with outside callers, turn call
sharing mode off (page 38).
Transferring a cellular call
between the base unit and a
cellular phone
Transferring a cellular call from the
base unit to a cellular phone
During a cellular call, press and hold MCELL
1N or MCELL 2N until the SP-PHONE indicator
goes out.
R The cellular call is transferred to the cellular
phone.
Using the other line during a
conversation
You can handle a cellular call and a landline
call at the same time. When another call is
being received during a conversation, the
interrupt tone sounds (page 37). You can
answer the 2nd call while holding the 1st call.
Making/answering a cellular call
during a conversation on the landline
1
2
3
Press MHOLDN during a landline call.
To make a 2nd call:
Press MCELL 1N or MCELL 2N. a Dial the
phone number.
To answer a 2nd call:
Press MCELL 1N or MCELL 2N.
R To hold the 2nd call, press MHOLDN.
To hang up the 2nd call and return to the
1st call (landline call), press
MSP-PHONEN 2 times.
Making/answering a landline call
during a conversation on a cellular line
1
2
3
Press MHOLDN during a cellular call.
To make a 2nd call:
MSP-PHONEN a Dial the phone number.
To answer a 2nd call:
MSP-PHONEN
R To hold the 2nd call, press MHOLDN.
To hang up the 2nd call and return to the
1st call (cellular call), press
MSP-PHONEN, then press MCELL 1N or
MCELL 2N.
Transferring a cellular call from a
cellular phone to the base unit
During a conversation using a cellular phone,
press MCELL 1N or MCELL 2N.
R The cellular call is transferred to the base
unit.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p29
29
2011/11/21
12:02:13
29
Shared Phonebook
Shared phonebook
The shared phonebook allows you to make
calls without having to dial manually. Any
handset registered to the base unit can use
the shared phonebook. You can add 3,050
names and phone numbers to the shared
phonebook, and assign each phonebook entry
to the desired group (“Home”, “Cell 1”,
“Cell 2”).
Important:
R Only 1 person can access the shared
phonebook at a time.
R Caller ID subscribers can use group ringer
tone features (page 43).
R You can copy phonebook entries from a
Bluetooth cellular phone to the unit’s
shared phonebook (page 46).
Key
Character
4
G
H
I
4
g
h
i
4
J
K
L
5
j
k
l
5
M
N
O
6
m
n
o
6
P
Q
R
S
7
p
q
r
s
7
T
U
V
8
t
u
v
8
W
X
Y
Z
9
w
x
y
z
9
5
6
7
8
9
#
Adding entries
1
2
M
N a MADDN
Enter the party’s name (16 characters
max.). a MOKN
3
Enter the party’s phone number (24 digits
max.). a MOKN
4
MbN: Select the desired group. a
MSELECTN 2 times
R To add other entries, repeat from step
2.
5
Character table for entering names
While entering characters, you can switch
between uppercase and lowercase by
pressing * (A®a).
1
2
3
30
&
’
(
/
1
)
A
B
C
2
a
b
c
2
D
E
F
3
d
e
f
3
H
,
R To enter another character that is located
on the same dial key, first press MEN to
move the cursor to the next space.
R If you do not press any dial key within 5
seconds after entering a character, the
character is fixed and the cursor moves to
the next space.
R in the above table represents a single
space.
Erasing the character or number
Groups
Character
.
#
Press MFN or MEN. a MCLEARN
R Press and hold MCLEARN to erase all
characters or numbers.
MOFFN
Key
0
0
–
Groups can help you find entries in the
phonebook quickly and easily. When adding
an entry to the phonebook, you can assign it
to one of 3 groups. You can search for
phonebook entries by group. The group ringer
tone feature is available for Caller ID
subscribers (page 43).
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p30
30
2011/11/21
12:02:13
Shared Phonebook
Finding and calling from a
phonebook entry
2
Scrolling through all entries
n Using a cellular line
1
2
3
M
N
MbN: Select the desired entry.
MCELLN
R The unit starts dialing when:
– only 1 cellular phone is registered.
– a specific line is set to make cellular
calls (page 20).
3
4
5
4
MbN: Select the desired cellular phone. a
MSELECTN
n Using the landline
1
2
3
M
N
MbN: Select the desired entry.
M
1
2
M
N
Press the dial key (0 – 9 or #) which
contains the character you are searching
for (page 30).
R Press the same dial key repeatedly to
display the first entry corresponding to
each character located on that dial key.
R If there is no entry corresponding to
the character you selected, the next
entry is displayed.
3
MbN: Scroll through the phonebook if
necessary.
4
To make a cellular/landline call, continue
from step 3, “Scrolling through all entries”,
page 31.
Searching by query
You can narrow down the search to enter the
first characters of a name.
1
M
Na*
MOKN
MbN: Scroll through the phonebook if
necessary.
To make a cellular/landline call, continue
from step 3, “Scrolling through all entries”,
page 31.
Searching by group
1
2
N
Searching by first character
To search for the name, enter the first
characters (up to 4) in uppercase
(page 30).
R Characters cannot be entered in
lowercase.
R If there is no entry corresponding to
the characters you selected, the next
entry is displayed.
3
4
M
N a MGROUPN
MbN: Select the group you want to search.
a MSELECTN
R If you select “All”, the unit ends the
group search.
MbN: Select the desired entry.
To make a cellular/landline call, continue
from step 3, “Scrolling through all entries”,
page 31.
Editing entries
1
2
3
Find the desired entry (page 31). a
MMENUN
MbN: “Edit” a MSELECTN
Edit the name if necessary (16 characters
max.; page 30). a MOKN
4
Edit the phone number if necessary (24
digits max.). a MOKN
5
MbN: Select the desired group (page 30).
a MSELECTN 2 times
6
MOFFN
Erasing entries
Erasing an entry
1
Find the desired entry (page 31). a
MERASEN
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p31
31
2011/11/21
12:02:13
31
Shared Phonebook
2
3
MbN: “Yes” a MSELECTN
MOFFN
Erasing all entries in a group
1
2
3
4
5
6
M
N a MMENUN
MbN: “Erase all” a MSELECTN
MbN: Select the desired group. a
MSELECTN
MbN: “Yes” a MSELECTN
MbN: “Yes” a MSELECTN
MOFFN
Chain dial
This feature allows you to dial phone numbers
in the phonebook while you are on a call. This
feature can be used, for example, to dial a
calling card access number or bank account
PIN that you have stored in the phonebook,
without having to dial manually.
1
2
3
During an outside call: MMENUN a
MbN: “Phonebook” a MSELECTN
MbN: Select the desired entry.
Press MCALLN to dial the number.
Note:
R When storing a calling card access number
and your PIN in the phonebook as one
phonebook entry, press MPAUSEN to add
pauses after the number and PIN as
necessary (page 22).
R If you have rotary/pulse service, you need
to press * (TONE) before pressing
MMENUN on the handset in step 1 to
change the dialing mode temporarily to
tone. When adding entries to the
phonebook, we recommend adding *
(TONE) to the beginning of phone numbers
you wish to chain dial (page 30).
32
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p32
32
2011/11/21
12:02:13
Programming
Programmable settings
You can customize the unit by programming the following features using the handset.
To access the features, there are 2 methods:
n Scrolling through the display menus
1 MMENUN
2
3
4
Press MCN or MDN to select the desired main menu. a MSELECTN
Press MCN or MDN to select the desired item from the next sub-menus. a MSELECTN
Press MCN or MDN to select the desired setting. a MSAVEN
R This step may vary depending on the feature being programmed.
R To exit the operation, press MOFFN.
n Using the direct command code
1 MMENUN a Enter the desired code.
Example: Press MMENUN#101.
2
Select the desired setting. a MSAVEN
R This step may vary depending on the feature being programmed.
R To exit the operation, press MOFFN.
Note:
R In the following table, < > indicates the default settings.
indicates the reference page number.
R In the following table,
R Display menu order and sub-menu may vary depending on your model.
Display the menu tree and direct command code table
Main menu:
“Caller list”
Operation
Code
Viewing the caller list.
#213
Main menu:
44
“Answering device”
Sub-menu 1
Sub-menu 2
Play new msg.
(msg.: message)
Settings
–
Code
–
#323
51
Play all msg.
–
–
#324
51
Erase all msg.*1
–
–
#325
51
Record greeting*1
–
#302
50
Check greeting
–
#303
50
Pre-recorded*1
(Reset to pre-recorded
greeting)
–
#304
50
Greeting
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p33
33
2011/11/21
12:02:13
33
Programming
Sub-menu 1
Sub-menu 2
Settings
Code
Settings
Ring count*1
2–7: 2-7 rings
<4 rings>
0: Toll saver
#211
53
Recording time*1
1: 1 min
3: <3 min>
0: Greeting only*2
#305
53
Remote code*1
<111>
#306
51
Screen call
1: <On> 0: Off
#310
49
Answer on*1
–
–
#327
49
Answer off*1
–
–
#328
49
Main menu:
“V.M. access”*3 (V.M.: Voice mail)
Operation
Code
Listening to voice mail messages.
#330
Main menu:
“Intercom”
Operation
Code
Paging the desired unit.
#274
34
56
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p34
34
2011/11/21
12:02:13
57
Programming
Main menu:
“Bluetooth”
Sub-menu 1
Sub-menu 2
Link to cell
– 1: Add new
device*4
(for CELL 1)
– 2: Add new
device*4
(for CELL 2)
Connect*1/
Disconnect*1
Settings
Code
–
#6251*5
Ringer volume
– Handset
0–6: Off–6 <6>
Ringer volume
– Base unit*1
0–6: Off–6 <1>
Ringer tone*7, *8
1–5: Tone 1-5
<Tone 2>*5
<Tone 4>*6
6–0: Melody 1-5
#6291*5
Select unit to
ring*1
1–6: Handset 1-6
G: <All>
#6271*5
Ring as cell
(limited)*1
1: <On (with
Talking CID)>
2: On (without
Talking CID)
0: Off
#6141*5
Registration
20
#6252*6
#6281*5
23
#6282*6
#G6281*5
28
#G6282*6
–
#6292*6
19
#6272*6
19
#6142*6
–
#6241*5
18
#6242*6
Phonebook
transfer
Headset
–
–
#618
46
Add new device*4
–
#621
47
Connect*1/
Disconnect*1
–
#622
47
Registration
–
#621
47
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p35
35
2011/11/21
12:02:14
35
Programming
Sub-menu 1
Sub-menu 2
Settings
Code
Settings
Auto connect*1
1: <1 min>
2: 3 min
3: 5 min
4: 10 min
0: Off
#632
–
#633
21
Cell line only
mode*1
1: On 0: <Off>
#157
20
Cell line select
– Handset
1: Cellphone 1*4
2: Cellphone 2*4
0: <Manual>
#634
20
Cell line select
– Base unit*1, *9
1: Cellphone 1*4
2: Cellphone 2*4
#G634
Set PIN*1
<0000>
#619
21
#134
21
Cell area code*1
–
Deregistration*2
Main menu:
–
“Set date & time”
Sub-menu 1
Sub-menu 2
Date and time*1
–
Alarm
–
Time
adjustment*1, *10
–
36
19
Settings
Code
–
#101
17
1: Once
2: Daily
0: <Off>
#720
40
1: <Caller ID
auto>
0: Manual
#226
–
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p36
36
2011/11/21
12:02:14
Programming
Main menu:
“Initial setting”
Sub-menu 1
Sub-menu 2
Settings
Code
Ringer setting
Ringer volume
– Handset*3
0–7: Off–7 <6>
#160
23
Ringer volume
– Base unit*1, *3
0–6: Off–6 <1>
#G160
28
Ringer tone*3, *7, *8, *11
(Handset)
1–5: Tone 1-5
<Tone 1>
6–0: Melody 1-5
#161
–
Interrupt tone
– Handset*12
1: <On> 0: Off
#201
25
Interrupt tone
– Base unit*1, *9, *12
1: <On> 0: Off
#G201
29
Silent mode
– On/Off
1: On 0: <Off>
#238
40
Silent mode
– Start/End
<11:00 PM/06:00
AM>
#237
40
Set date & time
Talking Caller ID
#101
17
Alarm
1: Once
2: Daily
0: <Off>
–
#720
40
Time adjustment*1, *10
1: <Caller ID
auto>
0: Manual
#226
–
Handset
1: <On> 0: Off
#162
43
Base unit*1
1: On 0: <Off>
#G162
Date and time*1
Handset name
–
–
#104
40
Call block*1
–
–
#217
41
#240
41
#331
55
Block w/o num*1, *2
(Block calls without
phone number)
Voice mail*3
Store VM access#*1
(VM: Voice mail)
1: On 0: <Off>
–
1: <On> 0: Off
#332
55
Message alert
–
1: <On> 0: Off
#340
53
LCD contrast
(Display contrast)
–
1–6: Level 1–6 <3>
#145
–
Key tone*13
–
1: <On> 0: Off
#165
–
VM tone detect*1
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p37
37
2011/11/21
12:02:14
37
Programming
Sub-menu 1
Settings
Code
Caller ID edit
(Caller ID number auto
edit)
–
1: <On> 0: Off
#214
44
Auto talk*14
–
1: On 0: <Off>
#200
23
mode*1
1: Pulse
2: <Tone>
#120
17
Set flash time*1, *15
0: 900 ms
1: <700 ms>
2: 600 ms
3: 400 ms
4: 300 ms
5: 250 ms
G: 200 ms
#: 160 ms
6: 110 ms
7: 100 ms
8: 90 ms
9: 80 ms
#121
24
Set line mode*1, *16
1: A 2: <B>
#122
–
1: <On> 0: Off
#194
24,
29
Set tel
Sub-menu 2
line*3
Set dial
–
Call sharing*1
Registration
Change language
Main menu:
Register handset
–
#130
42
Deregistration*2
–
#131
42
Display
1: <English>
2: Español
#110
17
Voice prompt*1
1: <English>
2: Español
#112
17
“Customer support”
Operation
Code
Displaying customer support Web address.
#680
*1
*2
*3
*4
*5
*6
*7
38
–
If you program these settings using one of the handsets, you do not need to program the
same item using another handset.
This menu is not displayed when scrolling through the display menus. It is only available in
direct command code.
When the cellular line only mode is turned on, these menus are not displayed (page 20).
After the Bluetooth device is registered, the device name is displayed.
For CELL 1
For CELL 2
If you select one of the melody ringer tones, the ringer tone continues to play for several
seconds even if the caller has already hung up. You may either hear a dial tone or no one on
the line when you answer the call.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p38
38
2011/11/21
12:02:14
Programming
*8
*9
*10
*11
*12
*13
*14
*15
*16
The preset melodies in this product are used with permission of © 2009 Copyrights Vision
Inc.
KX-TG7741 series: page 3
This feature allows the unit to automatically adjust the date and time each time caller
information including date and time is received.
To turn this feature on, select “Caller ID auto”. To turn this feature off, select
“Manual”. (Caller ID subscribers only)
To use this feature, set the date and time first (page 17).
If you subscribe to a distinctive ring service (such as IDENTA-RING), select a tone (tone 1 to
5). If you select a melody, you cannot distinguish lines by their ringers.
This tone lets you know when you receive an outside call while you are on another line or an
intercom call. If you select “On”, the tone sounds 2 times.
Turn this feature off if you prefer not to hear key tones while you are dialing or pressing any
keys, including confirmation tones and error tones.
If you subscribe to a Caller ID service and want to view the caller’s information after lifting up
the handset to answer a call, turn off this feature.
The flash time depends on your telephone exchange or host PBX. Contact your PBX
supplier if necessary. The setting should stay at “700 ms” unless pressing MFLASHN fails to
pick up the waiting call.
Generally, the line mode setting should not be changed. This setting automatically maintains
receiver volume at the proper level depending on the current telephone line condition. Set
the line mode to “A” if telephone line condition is not good.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p39
39
2011/11/21
12:02:14
39
Programming
Special programming
Alarm
An alarm sounds at the set time for 3 minutes
once or daily. Alarm can be set for each
handset.
Important:
R Set the date and time beforehand
(page 17).
1
2
MMENUN#720
MbN: Select the desired alarm option. a
MSELECTN
Off
Turns alarm off. Go to step 7.
Once
An alarm sounds once at the
set time.
Daily
An alarm sounds daily at the
set time. Go to step 4.
3
Enter the desired month and date. a
MOKN
4
5
6
Set the desired time.
7
Turning silent mode on/off
1
2
3
4
5
6
7
MAM/PMN: Select “AM” or “PM”. a MOKN
MbN: Select the desired alarm tone. a
MSELECTN
R We recommend selecting a different
ringer tone from the one used for
outside calls.
MSELECTN a MOFFN
R When the alarm is set,
Silent mode
Silent mode allows you to select a period of
time during which the handset will not ring for
outside calls. This feature is useful for time
periods when you do not want to be disturbed,
MMENUN#238
MbN: Select the desired setting. a
MSAVEN
R If you select “Off”, press MOFFN to
exit.
Enter the desired hour and minute you
wish to start this feature.
MAM/PMN: Select “AM” or “PM”. a MOKN
Enter the desired hour and minute you
wish to end this feature.
MAM/PMN: Select “AM” or “PM”.
MSAVEN a MOFFN
R When the silent mode is set,
displayed.
1
2
MMENUN#237
Continue from step 3, “Turning silent
mode on/off”, page 40.
Changing the handset name
Each handset can be given a customized
name (“Bob”, “Kitchen”, etc.). This is useful
when you make intercom calls between
handsets. You can also select whether or not
the handset name is displayed in standby
mode. The default setting is “No”. If you select
“Yes” without entering any handset name,
“Handset 1” to “Handset 6” is displayed.
1
MMENUN#104
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p40
40
is
Changing the start and end time
is displayed.
Note:
R To stop the alarm, press MOFFN or place
the handset on the base unit or charger.
R When the handset is in use, the alarm will
not sound until the handset is in standby
mode.
40
for example, while sleeping. Silent mode can
be set for each handset.
Important:
R Set the date and time beforehand
(page 17).
R We recommend turning the base unit ringer
off (page 35, 37) in addition to turning the
silent mode on.
R If you have set the alarm, the alarm sounds
even if the silent mode is turned on.
2011/11/21
12:02:14
Programming
2
3
4
5
2
Enter the desired name (max. 10
characters; see the character table,
page 30).
R If not required, go to step 3.
MSAVEN
3
4
5
6
MbN: Select the desired setting. a
MSELECTN 2 times
MOFFN
Call block (Caller ID subscribers
only)
This feature allows the unit to reject calls when:
– the unit receives a call from a phone
number stored in the call block list as
unwanted (“Storing unwanted callers”,
page 41).
– the unit receives a call without phone
number (“Blocking incoming calls without
phone number”, page 41).
When a call is received, the unit rings for a
short time while the caller is being identified. If
the phone number matches an entry in the call
block list:
– cellular calls are rejected.
– landline calls are disconnected after the
unit first sends out a busy tone to the caller.
Important:
R When the unit receives a call from a
number that is stored in the call block list or
a call without a recognized phone number,
the call is logged in the caller list
(page 44) with
after the call is
disconnected.
Storing unwanted callers
You can store up to 30 phone numbers in the
call block list.
Important:
R We recommend storing 10 digits (including
an area code). If only 7 digits are stored, all
numbers that have the same last 7 digits
will be blocked.
n From the caller list:
1 MFN CID
7
MbN: Select the entry to be blocked.
R To edit the number, press
MSELECTN, then press MEDITN
repeatedly until the phone number
is shown in the 10-digit format.
MSAVEN
MbN: “Call block” a MSELECTN
MbN: “Yes” a MSELECTN
Edit the phone number if necessary
(24 digits max.).
MSAVEN a MOFFN
n By entering phone numbers:
1 MMENUN#217 a MADDN
2
Enter the phone number (24 digits
max.).
R To erase a digit, press MCLEARN.
3
MSAVEN a MOFFN
Blocking incoming calls without
phone number
You can reject a call when no phone number
is provided, such as a call just showing “Out
of area”.
1
2
MMENUN#240
MbN: Select the desired setting. a
MSAVEN a MOFFN
Viewing/editing/erasing call block
numbers
1
2
MMENUN#217
MbN: Select the desired entry.
R To exit, press MOFFN.
3
To edit a number:
MEDITN a Edit the phone number. a
MSAVEN a MOFFN
To erase a number:
MERASEN a MbN: “Yes” a MSELECTN
a MOFFN
Note:
R When editing, press the desired dial key to
add, MCLEARN to erase.
R When viewing, “Block w/o num” is
displayed if the blocking incoming calls
without phone number feature is turned on.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p41
41
2011/11/21
12:02:14
41
Programming
To turn the feature off: MERASEN a MCN
a MSAVEN a MOFFN
Registering a unit
Operating additional units
Additional handsets
the same base unit. This allows the handset to
end its wireless connection with the system.
1
MMENUN#131
R All handsets registered to the base unit
are displayed.
2
MbN: Select the handset you want to
cancel. a MSELECTN
3
4
MbN: “Yes” a MSELECTN
MOFFN
Up to 6 handsets can be registered to the
base unit.
Important:
R See page 5 for information on the available
model.
Registering a handset to the
base unit
The supplied handset and base unit are
pre-registered. If for some reason the handset
is not registered to the base unit, re-register
the handset.
1
Handset:
MMENUN#130
2
Base unit:
Press and hold MLOCATORN for about 5
seconds until the registration tone sounds.
R If all registered handsets start ringing,
press MLOCATORN again to stop, then
repeat this step.
R The next step must be completed
within 90 seconds.
3
Handset:
Press MOKN, then wait until a long beep
sounds.
Note:
R While registering, “Base in
registering” is displayed on all
registered handsets.
R When you purchase an additional handset,
refer to the additional handset’s installation
manual for registration.
Deregistering a handset
A handset can cancel its own registration to
the base unit, or other handsets registered to
42
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p42
42
2011/11/21
12:02:14
Caller ID Service
Using Caller ID service
Important:
R This unit is Caller ID compatible. To use
Caller ID features, you must subscribe to a
Caller ID service. Contact your service
provider/telephone company for details.
Caller ID features
When an outside call is being received, the
caller’s name and phone number are
displayed.
Caller information for the last 50 callers is
logged in the caller list from the most recent
call to the oldest.
R If the unit cannot receive caller information,
the following is displayed:
– “Out of area”: The caller dials from
an area which does not provide a Caller
ID service.
– “Private caller”: The caller
requests not to send caller information.
– “Long distance”: The caller makes a
long distance call.
R If the unit is connected to a PBX system,
caller information may not be properly
received. Contact your PBX supplier.
Missed calls
If a call is not answered, the unit treats it as a
missed call. The display shows “Missed
call”.
Note:
R Even when there are unviewed missed
calls, “Missed call” disappears from the
standby display if the following operation is
performed by one of the units:
– A handset is replaced on the base unit
or charger.
– Pressing MOFFN on a handset.
Phonebook name display
When caller information is received and it
matches a phone number stored in the
phonebook, the stored name in the
phonebook is displayed and logged in the
caller list.
Talking Caller ID
Handset / Base unit
This feature lets you know who is calling
without looking at the display.
To use this feature, you must:
– subscribe to a Caller ID service of your
service provider/telephone company.
– turn this feature on (page 37).
When caller information is received, the
handsets and base unit announce the caller’s
name or phone number received from your
service provider/telephone company following
every ring.
The unit announces in English only.
R Name pronunciation may vary. This feature
may not pronounce all names correctly.
R Caller ID service has a limit of how many
characters can be displayed. If the caller’s
name is too long:
– the handset may not be able to display
or announce the entire name.
– the base unit may not be able to
announce the entire name.
R The announcement is heard at the same
level as the ringer volume (page 23, 28).
R If you turn on the answering system and set
the number of rings “2 rings” (page
53), the unit does not announce the caller
information from the landline. If “Toll
saver” is selected and there is a new
message, the unit does not announce the
caller information from the landline.
R When you receive a call while on the
phone, the 2nd caller’s name is not
announced even if you subscribe to both
Caller ID and Call Waiting with Caller ID
services.
Phonebook name announcement
When caller information is received and it
matches a phone number stored in the
phonebook, the stored name in the
phonebook is announced.
Ringer ID
You can select the desired ringer tone to a
group that each phonebook entry is assigned
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p43
43
2011/11/21
12:02:14
43
Caller ID Service
(page 30). When a call is received from a
caller assigned to a group, the ringer tone you
selected for that group rings instead of the
called line’s ringer tone (page 19, 35, 37) after
caller information is displayed. If you select
“Current ringer” (default), the unit uses
the called line’s ringer tone when calls from
this group are received.
1
2
3
M
N a MMENUN
MbN: “Group” a MSELECTN
MbN: Select the desired group. a
MSELECTN
4
MbN: Select the desired ringer tone. a
MSAVEN
5
MOFFN
Important:
R Only 1 person can access the caller list at a
time.
R Make sure the unit’s date and time setting
is correct (page 17).
Viewing the caller list and calling
back
n Using a cellular line
MFN CID
Press M N to search from the most recent
call, or M N to search from the oldest call.
3
To call back, press MSELECTN.
To exit, press MOFFN.
4
MCELLN
R The unit starts dialing when:
– only 1 cellular phone is registered.
– a specific line is set to make cellular
calls (page 20).
5
MbN: Select the desired cellular phone. a
MSELECTN
n Using the landline
1
2
44
To call back, press M
To exit, press MOFFN.
N.
Note:
R If the entry has already been viewed or
answered, “ ” is displayed, even if it was
viewed or answered using another unit.
R In step 2, if is displayed, not all of the
information is shown. To see the remaining
information, press MEN. To return to the
previous screen, press MFN.
R
or
indicates the caller information
was received from the cellular line.
Editing a caller’s phone number
before calling back
You can edit a phone number in the caller list
by removing its area code and/or the long
distance code “1”.
Caller list
1
2
3
MFN CID
Press MCN to search from the most recent
call, or MDN to search from the oldest call.
1
2
3
MFN CID
MbN: Select the desired entry.
Press MSELECTN, then press MEDITN
repeatedly until the phone number is
shown in the desired format.
A Local phone number
Example: 321-5555
B Area code – Local phone number
Example: 555-321-5555
C 1 – Area code – Local phone number
Example: 1-555-321-5555
4
Using a cellular line:
To make a cellular call, continue from
step 4, “Viewing the caller list and calling
back”, page 44.
Using the landline:
N
M
Caller ID number auto edit feature
Once you call back an edited number, the unit
which was used to call back remembers the
area code and format of the edited number.
The next time someone calls from the same
area code, caller information is customized by
the unit as follows:
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p44
44
2011/11/21
12:02:14
Caller ID Service
– When the call is being received, the Caller
ID number is displayed in the same format
as the edited number.
– After the call has ended, the caller’s phone
number is displayed in the same format as
the edited number, when reviewed from the
caller list.
For example, you can use this feature to set
the unit to ignore the area code of callers in
your area, so that you can call these local
numbers using caller information without
dialing the area code.
To activate this feature, you must edit an entry
in the caller list, then call that number. After
that, phone numbers from that caller’s area
code are edited automatically.
This feature can be set for each handset
(page 38). The default setting is “On”.
4
5
MbN: “Phonebook” a MSELECTN
Continue from step 3, “Editing entries”,
page 31.
Note:
R Phone numbers from the 4 most recently
edited area codes are automatically edited.
Erasing selected caller
information
1
2
3
4
MFN CID
MbN: Select the desired entry.
MERASEN a MbN: “Yes”
MSELECTN a MOFFN
Erasing all caller information
1
2
3
MFN CID
MERASEN a MbN: “Yes”
MSELECTN a MOFFN
Storing caller information to the
phonebook
1
2
3
M N CID
MbN: Select the desired entry.
R To edit the number, press MSELECTN,
then press MEDITN repeatedly until the
phone number is shown in the desired
format.
MSAVEN
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p45
45
2011/11/21
12:02:14
45
Using Bluetooth Devices
Copying phonebook from a
cellular phone (phonebook
transfer)
You can copy phonebook entries from the
registered cellular phones or other cellular
phones (not registered) to the unit’s shared
phonebook. A cellular phone must be
Bluetooth wireless technology compatible.
Important:
R If a copied entry has 2 or more phone
numbers, each phone number (6 max.) is
stored as a separate entry with the same
name.
R If a phonebook entry includes additional
data such as a picture, that entry may fail to
copy to the base unit.
1
Handset:
MMENUN#618
2
Handset:
To copy from registered cellular
phones:
MbN: Select the desired cellular phone. a
MSELECTN
R Copied items are stored to the group
(“Cell 1” or “Cell 2”) which the
cellular phone is registered to.
To copy from other cellular phones
(not registered):
MbN: “Other cell” a MSELECTN a
MbN: Select the group you want to copy to.
a MSELECTN
3
When “Transfer phonebook from
cell.” is displayed:
Go to step 4.
When “Select mode” menu is
displayed:
MbN: Select “Auto” or “Manual”. a
MSELECTN
“Auto”: Download all entries from the
cellular phone automatically. Go to step 5.
“Manual”: Copy entries you selected.
R “Select mode” menu is displayed
only when the cellular phone supports
PBAP (Phone Book Access Profile) for
Bluetooth connection.
46
4
Cellular phone:
Follow the instructions of your cellular
phone to copy phonebook entries.
R For other cellular phones (not
registered), you need to search for and
select the base unit. The base unit PIN
(default: “0000”) may be required.
R The entries being copied are displayed
on the handset.
5
Handset:
Wait until “Completed” is displayed.
R You can continue copying other entries
if necessary.
6
Handset: MOFFN
Note:
R Some copied entries may have characters
which do not exist in the character table
(page 30). These characters can be
displayed but cannot be entered when
editing an entry.
R The unit does not support some characters.
If a copied entry includes those characters,
they are replaced with other available
characters or “H”.
R If you receive a call while copying
phonebook entries, the copying procedure
stops. Try again after finishing the call.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p46
46
2011/11/21
12:02:14
Using Bluetooth Devices
Using a Bluetooth wireless
headset (optional) for
landline calls
By registering a Bluetooth headset to the base
unit, you can have a hands-free conversation
wirelessly for landline calls.
Important:
R 1 headset can be registered to the base
unit. However, only one Bluetooth device
(cellular phone or headset) can be
connected to the base unit at a time.
R For best performance, we recommend
using a Bluetooth headset within 1 m
(3.3 feet) of the base unit. A headset can
communicate with the base unit within a
range of approximately 10 m (33 feet).
Registering a headset to the base
unit
Important:
R Make sure that the Bluetooth headset is not
connected to any other Bluetooth device.
To use your headset with another Bluetooth
device such as a cellular phone, you may
need to disconnect it from the base unit.
Important:
R Make sure that the headset is turned on.
Base unit*1
*1
KX-TG7741 series: page 3
To connect:
Press MHEADSETN.
To disconnect:
Press and hold MHEADSETN until a long beep
sounds.
Handset
1
To connect/disconnect:
MMENUN#622
R A long beep sounds.
2
MOFFN
Deregistering a headset
You can cancel a registration of the headset
that is stored to the base unit. See
“Deregistering Bluetooth devices”, page 21.
Operating a Bluetooth wireless
headset using a landline
1
Your headset:
Set your headset to registration mode.
R Refer to the headset operating
instructions.
2
Handset:
MMENUN#621
Important:
R Refer to your headset operating instructions
for headset operations.
3
Enter your headset PIN.
R Typically, default PIN is “0000”. Refer
to the headset operating instructions.
4
Answering landline calls with your
headset
Press MOKN, then wait until a long beep
sounds.
5
MOFFN
R When the HEADSET indicator on the
base unit lights green, you are ready to
use the headset.
Connecting/disconnecting a headset
If you cannot connect the headset and base
unit using the headset, you can connect using
the unit.
To answer a landline call, turn on your
headset referring to your headset operating
instructions.
When you finish talking, turn off your headset
referring to your headset operating
instructions.
Note:
R If you cannot hang up the call using your
headset;
– press MnN (STOP) on the base unit.
(KX-TG7731 series: page 3)
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p47
47
2011/11/21
12:02:14
47
Using Bluetooth Devices
– press MSP-PHONEN on the base unit 2
times. (KX-TG7741 series: page 3)
Switching between the base unit and
your headset
You can switch between the base unit and
your headset:
– during a landline call with the base unit
speakerphone. (KX-TG7741 series: page 3)
– during an intercom call between the base
unit and handset. (KX-TG7741 series:
page 3)
– while listening to messages recorded on
the base unit answering system.*1
n KX-TG7741 series: page 3
To switch to your headset:
Press MHEADSETN on the base unit.
To switch to the base unit:
Press MSP-PHONEN on the base unit.
*1 KX-TG7731 series: page 3
R You can only switch from the base unit
to your headset. Turn on the headset
referring to your headset operating
instructions.
Call sharing between your headset
and the handset
Important:
R To activate this feature, you should set call
sharing mode to on beforehand (page 38).
n While the handset is on a landline call:
To join the conversation with your
headset, turn on the headset referring to
your headset operating instructions.
n While your headset is on a landline call:
To join the conversation with the handset,
N.
press M
Adjusting your headset receiver
volume
Base unit
Press MjN or MkN repeatedly while using your
headset.
48
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p48
48
2011/11/21
12:02:14
Answering System for Landline
Answering system for
landline
The answering system can answer and record
calls for you when you are unavailable to
answer the phone.
You can also set the unit to play a greeting
message but not to record caller messages by
selecting “Greeting only” as the recording
time setting (page 53).
Important:
R Only 1 person can access the answering
system (listen to messages, record a
greeting message, etc.) at a time.
R When callers leave messages, the unit
records the day and time of each message.
Make sure the date and time have been set
correctly (page 17).
R When the cellular line only mode is set
(page 20), the answering system cannot be
used and any messages are not received.
Memory capacity (including your
greeting message)
The total recording capacity is about 18
minutes. A maximum of 64 messages can be
recorded.
Note:
R When message memory becomes full:
– “Messages full” is shown on the
handset display.
– The ANSWER ON/OFF indicator on the
base unit flashes rapidly if the answering
system is turned on.
– The message counter on the base unit
flashes if the answering system is turned
on.
– If you use the pre-recorded greeting
message, the unit automatically switches
to another pre-recorded greeting
message asking callers to call again
later.
– If you recorded your own greeting
message, the same message is still
announced to callers even though their
messages are not recorded.
Turning the answering
system on/off
Base unit
Press MANSWER ON/OFFN to turn on/off the
answering system.
Handset
1
To turn on:
MMENUN#327
To turn off:
MMENUN#328
2
MOFFN
Note for base unit and handset:
R When the answering system is turned on:
– The ANSWER ON/OFF indicator on the
base unit lights up.
– The message counter on the base unit
displays the total number of messages
(old and new).
Call screening
While a caller is leaving a message, you can
listen to the call through the unit’s speaker.
Handset
To adjust the speaker volume, press MjN or
MkN repeatedly. You can answer the call by
pressing M
N. Call screening can be set for
each handset. The default setting is “On”.
1
2
MMENUN#310
MbN: Select the desired setting. a
MSAVEN a MOFFN
Base unit*1
*1
KX-TG7741 series: page 3
To adjust the speaker volume, press MjN or
MkN repeatedly. You can answer the call by
pressing MSP-PHONEN.
To turn off while screening a call, press MkN
repeatedly until the sounds goes off.
R If you adjust the speaker volume while
listening to messages or having a
conversation, the speaker volume for call
screening is turned on again.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p49
49
2011/11/21
12:02:14
49
Answering System for Landline
Greeting message
When the unit answers a call, a greeting
message is played to callers.
You can use either:
– your own greeting message
– a pre-recorded greeting message
Recording your greeting message
1
2
3
4
5
MMENUN#302
MbN: “Yes” a MSELECTN
After a beep sounds, hold the handset
about 20 cm (8 inches) away and speak
clearly into the microphone (2 minutes
max.).
Press MSTOPN to stop recording.
MOFFN
Using a pre-recorded greeting
message
The unit provides 2 pre-recorded greeting
messages:
– If you erase or do not record your own
greeting message, the unit plays a
pre-recorded greeting asking callers to
leave a message.
– If the message recording time (page 53)
is set to “Greeting only”, callers’
messages are not recorded and the unit
plays a different pre-recorded greeting
message asking callers to call again.
Resetting to a pre-recorded greeting
message
If you want to use a pre-recorded greeting
message once you record your own greeting
message, you need to erase your own
greeting message.
1
2
Playing back the greeting
message
1
2
MMENUN#303
To exit, press MOFFN.
Listening to messages
using the base unit
When new messages have been recorded,
M N on the base unit flashes.
Press M N (PLAY).
R If new messages have been recorded, the
base unit plays back new messages.
R If there are no new messages, the base
unit plays back all messages.
Operating the answering system
during playback
Key
Operation
MjN or MkN
Adjust the speaker volume
M
N
Repeat message*1
M
N
Skip message
MnN (STOP)
Stop playback
MERASEN
Erase currently playing
message
*1
If pressed within the first 5 seconds of a
message, the previous message is
played.
Erasing all messages
Press MERASEN 2 times while the unit is not in
use.
Listening to messages
using the handset
MMENUN#304
MYESN a MOFFN
When new messages have been recorded:
– “New message” is displayed.
50
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p50
50
2011/11/21
12:02:14
Answering System for Landline
– The message indicator on the handset
flashes slowly if the message alert feature
is turned on (page 53).
1
2
To listen to new messages:
MMENUN#323
To listen to all messages:
MMENUN#324
MbN: “Playback” a MSELECTN
You can also erase as follows:
MERASEN a MbN: “Yes” a MSELECTN
Calling back (Caller ID
subscribers only)
When finished, press MOFFN.
Note:
R To switch to the receiver, press M
*3
N.
Operating the answering system
MMENUN a MbN: “Answering device” a
MSELECTN
If caller information is received for the call, you
can call the caller back while listening to a
message.
1
2
Press MPAUSEN during playback.
MbN: “Call back” a MSELECTN
Editing the number before calling back
1
2
3
Press MPAUSEN during playback.
Key
Operation
MjN or MkN
Adjust the receiver/speaker
volume
(during playback)
1 or MFN
Repeat message
(during playback)*1
2 or MEN
Skip message
(during playback)
3
Enter the “Settings” menu
Erasing all messages
4
Play new messages
5
Play all messages
6
Play greeting message
1
2
76
Record greeting message
8
Turn answering system on
MPAUSEN
Pause message*2
9 or
MSTOPN
Stop recording
Stop playback
0
Turn answering system off
*4*3
Erase currently playing
message
*5
Erase all messages
*6
Reset to a pre-recorded
greeting message
*1
*2
If pressed within the first 5 seconds of a
message, the previous message is
played.
To resume playback:
MbN: “Edit & Call” a MSELECTN
Press MEDITN repeatedly until the phone
number is shown in the desired format
(page 44). a M
N
R To call back using a cellular line,
continue from step 2, “Making cellular
calls”, page 22.
MMENUN#325
MbN: “Yes” a MSELECTN a MOFFN
Remote operation
Using a touch-tone phone, you can call your
phone number from outside and access the
unit to listen to messages or change
answering system settings. The unit’s voice
guidance prompts you to press certain dial
keys to perform different operations.
Remote access code
A 3-digit remote access code must be entered
when operating the answering system
remotely. This code prevents unauthorized
parties from listening to your messages
remotely. The default setting is “111”.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p51
51
2011/11/21
12:02:15
51
Answering System for Landline
Important:
R To prevent unauthorized access to this
product, we recommend that you regularly
change the remote code.
1
2
MMENUN#306
Remote commands
You can press dial keys to access certain
answering system functions without waiting for
the voice guidance to prompt you.
Key
Operation
1
Repeat message
(during playback)*1
2
Skip message
(during playback)
Press * in step 2 on “Remote access code”,
page 51.
R The entered remote access code is deleted.
4
Play new messages
5
Play all messages
9
Stop playback*2
Start voice guidance*3
Using the answering system
remotely
0
Turn answering system off
*4
Erase currently playing message
1
*5
Erase all messages
*#
End remote operation
(or hang up)
3
Enter the desired 3-digit remote access
code.
MSAVEN a MOFFN
Deactivating remote operation
Dial your landline phone number from a
touch-tone phone.
2
After the greeting message starts, enter
your remote access code.
3
Follow the voice guidance prompts as
necessary or control the unit using
remote commands (page 52).
4
When finished, hang up.
Voice guidance
n When the English voice guidance is
selected
During remote operation, the unit’s voice
guidance starts and prompts you to press
1 to perform a specific operation, or
press 2 to listen to more available
operations.
n When the Spanish voice guidance is
selected
To start the voice guidance, press 9. The
voice guidance announces the available
remote commands (page 52).
Note:
R If you do not press any dial keys within 10
seconds after a voice guidance prompt, the
unit disconnects your call.
52
*1
*2
*3
If pressed within the first 5 seconds of a
message, the previous message is
played.
For English voice guidance only
For Spanish voice guidance only
Turning on the answering system
remotely
If the answering system is off, you can turn it
on remotely.
1
Dial your phone number from a
touch-tone phone.
2
Let the phone ring 15 times.
R A long beep is heard.
3
Enter your remote access code within 10
seconds after the long beep.
R The greeting message is played back.
R You can either hang up, or enter your
remote access code again and begin
remote operation (page 51).
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p52
52
2011/11/21
12:02:15
Answering System for Landline
by your service provider/telephone
company before changing this setting.
– Change the number of rings of the voice
mail service so that the answering
system can answer the call first. To do
so, contact your service provider/
telephone company.
Answering system settings
Number of rings before the unit
answers a call
You can change the number of times the
phone rings “Ring count” before the unit
answers calls. You can select 2 to 7 rings, or
“Toll saver”.
The default setting is “4 rings”.
“Toll saver”: The unit’s answering system
answers at the end of the 2nd ring when new
messages have been recorded, or at the end
of the 5th ring when there are no new
messages. If you call your phone from outside
to listen to new messages (page 51), you
know that there are no new messages when
the phone rings for the 3rd time. You can then
hang up without being charged for the call.
1
2
MMENUN#211
MbN: Select the desired setting. a
MSAVEN a MOFFN
For voice mail service subscribers
If you subscribe to a flat-rate service package
that includes Caller ID, call waiting, voice mail,
and unlimited local/regional/long distance
calls, please note the following:
R To use the voice mail service provided by
your service provider/telephone company
rather than the unit’s answering system,
turn off the answering system (page 49).
R To use this unit’s answering system rather
than the voice mail service provided by
your service provider/telephone company,
please contact your service provider/
telephone company to deactivate your
voice mail service.
If your service provider/telephone company
cannot do this:
– Set this unit’s “Ring count” setting so
that this unit’s answering system
answers calls before the voice mail
service of your service provider/
telephone company does. It is necessary
to check the number of rings required to
activate the voice mail service provided
Caller’s recording time
You can change the maximum message
recording time allowed for each caller. The
default setting is “3 min”.
1
2
MMENUN#305
MbN: Select the desired setting. a
MSAVEN a MOFFN
Selecting “Greeting only”
You can select “Greeting only” which sets
the unit to announce a greeting message to
callers but not record messages.
Select “Greeting only” in step 2 on
“Caller’s recording time”, page 53.
Note:
R When you select “Greeting only”:
– If you do not record your own message,
the unit will play the pre-recorded
greeting-only message asking callers to
call again later.
– If you use your own message, record the
greeting-only message asking callers to
call again later (page 50).
Message alert
You can select whether or not the message
indicator on the handset flashes slowly when
new messages are recorded. The default
setting is “On”.
Important:
R If you stored the voice mail access number
(page 55), the message indicator also
flashes for newly recorded voice mail
messages from the landline (page 56).
1
2
MMENUN#340
MbN: Select the desired setting. a
MSAVEN a MOFFN
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p53
53
2011/11/21
12:02:15
53
Answering System for Landline
Note:
R While message alert is on, battery
operating time is shortened (page 12).
54
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p54
54
2011/11/21
12:02:15
Voice Mail Service for Landline
Example:
Voice mail service for
landline
Voice mail is an automatic answering service
offered by your service provider/telephone
company. After you subscribe to this service,
your service provider/telephone company’s
voice mail system answers calls for you when
you are unavailable to answer the phone or
when your line is busy. Messages are
recorded by your service provider/telephone
company, not your telephone. Please contact
your service provider/telephone company for
details of this service.
Important:
R To use the voice mail service provided by
your service provider/telephone company
rather than the unit’s answering system,
turn off the answering system (page 49).
For details, see page 53.
R You need to store the voice mail access
number to activate the message alert
feature (page 53) for voice mail service.
Storing the voice mail (VM)
access number
In order to listen to your voice mail messages,
you must dial your service provider/telephone
company’s voice mail access number. Once
you have stored your voice mail access
number, you can dial it automatically
(page 56).
1
2
MMENUN#331
Enter your access number (24 digits
max.). a MSAVEN a MOFFN
Note:
R When storing your voice mail access
number and your mailbox password, press
MPAUSEN to add pauses (page 22)
between the access number and the
password as necessary. Contact your
service provider/telephone company for the
required pause time.
1-222-333-4444
VM access
number
PPPP
Pauses
8888
Password
To erase the voice mail access
number
1
2
MMENUN#331
Press and hold MCLEARN until all digits
are erased. a MSAVEN a MOFFN
Voice mail (VM) tone detection
Handset / Base unit*1
*1
KX-TG7741 series: page 3
Your service provider/telephone company
sends special signals (sometimes called
“voice mail tones” or “stutter tones”) to the unit
to let you know you have new voice mail
messages. If you hear a series of dial tones
followed by a continuous dial tone after you
N on the handset or press
press M
MSP-PHONEN on the base unit, you have new
voice mail messages. Soon after you hang up
a call or after the phone stops ringing, your
unit checks the phone line to see if new voice
mail messages have been recorded.
Turn this feature off when:
– You do not subscribe to voice mail service.
– Your service provider/telephone company
does not send voice mail tones.
– Your phone is connected to a PBX.
If you are not sure which setting is required,
contact your service provider/telephone
company.
Turning VM tone detection on/off
The default setting is “On”.
1
2
MMENUN#332
MbN: Select the desired setting. a
MSAVEN a MOFFN
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p55
55
2011/11/21
12:02:15
55
Voice Mail Service for Landline
Listening to voice mail messages
The unit lets you know that you have new
voice mail messages in the following ways:
– “New Voice Mail” is displayed on the
handset if message indication service is
available.
– The message indicator on the handset
flashes slowly if the message alert feature
is turned on (“Message alert”, page 53).
Handset
1
MMENUN#330
R The speakerphone turns on.
2
3
Follow the pre-recorded instructions.
When finished, press MOFFN.
Note:
R If the handset still indicate there are new
messages even after you have listened to
all new messages, turn it off by pressing
and holding # until the handset beeps.
Base unit*1
*1
KX-TG7741 series: page 3
To listen to voice mail messages, you have to
dial your voice mail access number manually.
56
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p56
56
2011/11/21
12:02:15
Intercom/Locator
1
2
Intercom
Intercom calls can be made:
– between handsets
– between a handset and the base unit*1
*1 KX-TG7741 series: page 3
Note:
R When paging unit(s), the paged unit(s)
beeps for 1 minute.
R If you receive an outside call while talking
on the intercom, you hear 2 tones.
– To answer the call with the handset,
N.
press MOFFN, then press M
– To answer the call with the base unit,
press MSP-PHONEN 2 times.*1
*1 KX-TG7741 series: page 3
Making an intercom call
Handset
1
2
Press MINTERCOMN to answer the page.
When you finish talking, press
MINTERCOMN.
Handset locator
You can locate a misplaced handset by
paging it.
1
Base unit:
Press MLOCATORN.
R All registered handsets beep for 1
minute.
2
To stop paging:
Base unit:
Press MLOCATORN.
Handset:
n KX-TG7731 series: page 3
Press MOFFN.
n KX-TG7741 series: page 3
Press M
N, then press MOFFN.
MMENUN a MINTN
MbN: Select the desired unit. a MSELECTN
R To stop paging, press MOFFN.
3
When you finish talking, press MOFFN.
Base unit*1
*1
KX-TG7741 series: page 3
1
Press MINTERCOMN.
R To page a specific handset, enter the
handset number.
R To page all handsets, press 0 or wait
for a few seconds.
R To stop paging, press MINTERCOMN.
2
When you finish talking, press
MINTERCOMN.
Answering an intercom call
Handset
1
2
Press M
N to answer the page.
When you finish talking, press MOFFN.
Base unit*1
*1
KX-TG7741 series: page 3
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p57
57
2011/11/21
12:02:15
57
Intercom/Locator
R The outside call is being routed to the
handset.
To establish a conference call:
Press MCONFN.
R To leave the conference, press
MSP-PHONEN. The other 2 parties can
continue the conversation.
R To put the outside call on hold, press
MHOLDN. To resume the conference,
press MCONFN.
Transferring calls,
conference calls
Outside calls can be transferred or a
conference call with an outside party can be
made:
– between 2 handsets
– between a handset and the base unit*1
*1 KX-TG7741 series: page 3
Answering a transferred call
Handset
1
During an outside call, press MINTN to put
the call on hold.
2
3
MbN: Select the desired unit. a MSELECTN
Wait for the paged party to answer.
R If the paged party does not answer,
press M
N to return to the outside call.
4
Handset
Press M
N to answer the page.
Base unit*1
*1
KX-TG7741 series: page 3
Press MSP-PHONEN to answer the page.
To complete the transfer:
Press MOFFN.
R The outside call is being routed to the
destination unit.
To establish a conference call:
MMENUN a MbN: “Conference” a
MSELECTN
R To leave the conference, press MOFFN.
The other 2 parties can continue the
conversation.
R To put the outside call on hold:
MMENUN a MbN: “Hold” a
MSELECTN
To resume the conference: MMENUN
a MbN: “Conference” a MSELECTN
Base unit*1
*1
KX-TG7741 series: page 3
1
During an outside call, press
MINTERCOMN.
R To page a specific handset, enter the
handset number.
R To page all handsets, press 0 or wait
for a few seconds.
2
Wait for the paged party to answer.
R If paged party does not answer, press
MINTERCOMN to return to the outside
call.
3
To complete the transfer:
Press MSP-PHONEN.
58
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p58
58
2011/11/21
12:02:15
Useful Information
3
Wall mounting
Note:
R Make sure that the wall and the fixing
method are strong enough to support the
weight of the unit.
Insert the hooks on the wall mounting
adaptor into holes
and
on the base
unit.
1
2
Base unit
1
Thread the AC adaptor cord and
telephone line cord through the hole in
the wall mounting adaptor in the direction
of the arrow.
2
1
4
2
Adjust the adaptor to hold the base unit,
then push it in the direction of the arrow
until it clicks into place.
Tuck the telephone line cord inside the
wall mounting adaptor (A). Connect the
AC adaptor cord and telephone line cord
(B).
B
A
Hook
AC adaptor cord
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p59
59
2011/11/21
12:02:15
59
Useful Information
5
Mount the unit on a wall then slide down
to secure in place.
AC adaptor cord
To remove the wall mounting adaptor
While pushing down the release levers (A),
remove the adaptor (B).
A
A
1
2
83 mm
(3 1/4 inches)
or
102 mm
(4 inches)
1
Charger
Drive the screws (not supplied) into the wall.
25.4 mm
(1 inch)
Wall phone plate
83 mm
(3 1 / 4 inches)
B
102 mm
(4 inches)
Screws
2
Hooks
60
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p60
60
2011/11/21
12:02:15
Useful Information
Error messages
Display message
Cause/solution
Base no power
or
No link. Re-connect base
AC adaptor.
R The handset has lost communication with the base
unit. Move closer to the base unit and try again.
R Unplug the base unit’s AC adaptor to reset the unit.
Reconnect the adaptor and try again.
R The handset’s registration may have been canceled.
Re-register the handset (page 42).
Busy
R No cellular phone is registered to the base unit.
Register a cellular phone (page 18).
R The called unit is in use.
R Other units are in use and the system is busy. Try
again later.
R The handset you are using is too far from the base
unit. Move closer and try again.
Call phone company for
your access #
R You have not stored the voice mail access number.
Store the number (page 55).
Check tel line
R The supplied telephone line cord has not been
connected yet or not connected properly. Check the
connections (page 11).
R If you do not connect the telephone line cord and use
only cellular lines, set the cellular line only mode
(page 20).
Error!!
R Recording was too short. Try again.
R Someone is using a cellular line or headset. Try
again later.
R The phonebook copy is incomplete (page 46). The
cellular phone is disconnected from the base unit.
Make sure that other Bluetooth devices are not
connected to the cellular phone, and try again.
Failed
R Although the unit tried to connect to the cellular
phone or headset, the connection has been failed.
– Someone is using a cellular line or headset. Try
again later.
– Make sure that the cellular phone or headset is
not connected to other Bluetooth devices.
Invalid
R There is no handset registered to the base unit
matching the handset number you entered.
R The handset is not registered to the base unit.
Register the handset (page 42).
Requires subscription to
Caller ID.
R You must subscribe to a Caller ID service. Once you
receive caller information after subscribing to a Caller
ID service, this message will not be displayed.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p61
61
2011/11/21
12:02:15
61
Useful Information
Display message
Cause/solution
Use rechargeable battery.
R A wrong type of battery such as Alkaline or
Manganese was inserted. Use only the rechargeable
Ni-MH batteries noted on page 5, 8.
Troubleshooting
If you still have difficulties after following the instructions in this section, disconnect the base unit’s
AC adaptor, then reconnect the base unit’s AC adaptor. Remove the batteries from the handset,
and then insert the batteries into the handset again.
General use
Problem
Cause/solution
The handset does not turn on
even after installing charged
batteries.
R Place the handset on the base unit or charger to turn on
the handset.
The unit does not work.
R
R
R
R
I cannot register a cellular phone
to the base unit.
R Depending on the compatibility of the cellular phone,
you may not be able to register it to the base unit.
Confirm that your cellular phone supports the hands-free
profile (HFP) specification.
R Confirm that the Bluetooth feature of your cellular phone
is turned on. You may need to turn this feature on
depending on your cellular phone.
R The Bluetooth technology on your cellular phone may
not be functioning normally. Turn off and on your cellular
phone.
R If your cellular phone is already connected to another
Bluetooth device such as a Bluetooth headset, turn it off
or disconnect it from your cellular phone.
R Some cellular phones may require you to enter the base
unit PIN to register. Confirm that you entered the correct
PIN.
62
Make sure the batteries are installed correctly (page 11).
Fully charge the batteries (page 12).
Check the connections (page 11).
Unplug the base unit’s AC adaptor to reset the unit.
Reconnect the adaptor and try again.
R The handset has not been registered to the base unit.
Register the handset (page 42).
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p62
62
2011/11/21
12:02:15
Useful Information
Problem
Cause/solution
I cannot connect a cellular phone
to the base unit.
R Confirm that your cellular phone is turned on.
R Confirm that your cellular phone is within base unit
range (page 15).
R Depending on the state of the wireless environment,
such as the presence of any electrical interference,
there may be a delay even if the auto connection feature
is turned on. You can connect to the base unit manually
(page 20).
R The cellular phone has not been registered to the base
unit. Register the cellular phone (page 18).
I cannot hear a dial tone.
R Make sure the base unit’s AC adaptor is connected
properly (page 11).
R Make sure that the CELL 1 or CELL 2 indicator lights
green (page 16).
R Make sure the telephone line cord is connected properly
(page 11).
R Disconnect the base unit from the telephone line and
connect the line to a known working telephone. If the
working telephone operates properly, contact our
service personnel to have the unit repaired. If the
working telephone does not operate properly, contact
your service provider/telephone company.
The indicator on the handset
flashes slowly.
R New messages have been recorded. Listen to the new
messages (page 50).
R New voice mail messages have been recorded. Listen
to the new voice mail messages (page 56).
The receiver volume is changed
to level 4 (default), even though I
set it to level 5 (maximum level).
R The receiver volume returns to level 4 after you hang
up. Press MjN or MkN to adjust the volume every time
or as needed.
Programmable settings
Problem
Cause/solution
The display is in a language I
cannot read.
R Change the display language (page 17).
I cannot register a handset to a
base unit.
R The maximum number of handsets (6) is already
registered to the base unit. Cancel unused handset
registrations from the base unit (page 42).
Battery recharge
Problem
Cause/solution
The handset beeps and/or
flashes.
R Battery charge is low. Fully charge the batteries (page 12).
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p63
63
2011/11/21
12:02:15
63
Useful Information
Problem
Cause/solution
I fully charged the batteries, but
–
still flashes,
is displayed, or
–
– the operating time seems to
be shorter.
) and the charge contacts
R Clean the battery ends ( ,
with a dry cloth and charge again.
R It is time to replace the batteries (page 11).
Making/answering calls, intercom
Problem
Cause/solution
R The handset is too far from the base unit. Move closer.
R The base unit’s AC adaptor is not properly connected.
Reconnect AC adaptor to the base unit.
R The handset is not registered to the base unit. Register it
(page 42).
is displayed.
Noise is heard, sound cuts in
and out.
R You are using the handset or base unit in an area with
high electrical interference. Re-position the base unit and
use the handset away from sources of interference.
R Move closer to the base unit.
R If you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL filter between the base unit and
the telephone line jack. Contact your DSL/ADSL provider
for details.
The handset or base unit does
not ring.
R The ringer volume is turned off. Adjust the ringer volume
(page 35, 37).
R When one handset is selected to ring for cellular calls,
other units do not ring. To change the selection, see
page 19.
R Silent mode is turned on for the handset. Turn it off
(page 40).
I cannot make local calls with
the handset or base unit using
a cellular line.
R You need to add your area code when making cellular
calls. Store your area code in order to automatically add it
to the beginning of the 7-digit phone number when
making cellular calls (page 21).
I cannot make or answer
cellular calls with the handset
or base unit.
R Depending on the cellular phone’s compatibility, you may
not be able to make or answer cellular calls even if the
cellular phone is connected to the base unit.
R Make sure that the CELL 1 or CELL 2 indicator lights
green and the cellular phone is connected to the base unit
(page 20).
R If someone is talking on a cellular call or using the
headset, you cannot use the cellular feature. There can
be only one active Bluetooth connection at a time.
R The cellular phone is being used separately from your
system.
64
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p64
64
2011/11/21
12:02:15
Useful Information
Problem
Cause/solution
I can make and answer cellular
calls but cannot hear a sound.
R The Bluetooth technology on your cellular phone may not
be functioning normally. Turn off and on your cellular
phone.
R Disconnect and reconnect the base unit AC adaptor and
try again.
I cannot switch cellular calls
from the unit to the cellular
phone.
R Your cellular phone may not support this feature. Refer to
the operating instructions of your cellular phone.
I cannot make a call using the
landline.
R The dialing mode may be set incorrectly. Change the
setting (page 17).
R The cellular line only mode is turned on. Turn it off
(page 20).
I cannot make long distance
calls.
R Make sure that you have long distance service.
Caller ID/Talking Caller ID
Problem
Cause/solution
Caller information is not
displayed.
R You must subscribe to Caller ID service. Contact your
service provider/telephone company for details.
R If your unit is connected to any additional telephone
equipment such as a Caller ID box or cordless telephone
line jack, plug the unit directly into the wall jack.
R If you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL filter between the base unit and
the telephone line jack. Contact your DSL/ADSL provider
for details.
R The name display service for landline calls may not be
available in some areas. Contact your service provider/
telephone company for details.
R Other telephone equipment may be interfering with this
unit. Disconnect the other equipment and try again.
Caller information is displayed
or announced late.
R Depending on your service provider/telephone company,
the unit may display or announce the caller’s information
at the 2nd ring or later.
R Move closer to the base unit.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p65
65
2011/11/21
12:02:15
65
Useful Information
Problem
Cause/solution
Caller information is not
announced.
R The handset or base unit’s ringer volume is turned off.
Adjust it (page 23, 28, 35, 37).
R When one handset is selected to ring for cellular calls,
other units do not announce caller information. To change
the selection, see page 19.
R The Talking Caller ID feature is turned off. Turn it on
(page 37).
R The ring as cell mode is set to “On (without Talking
CID)”. To change the mode, see page 19.
R The number of rings for the answering system is set to “2
rings” or “Toll saver”. Select a different setting
(page 53).
R Your unit does not announce caller information if
– the base unit or 2 or more handsets are on a call.
– a headset is in use.
The caller list/incoming phone
numbers are not edited
automatically.
R The Caller ID number auto edit feature is turned off. Turn
it on and try again (page 38).
R You need to call back the edited number to activate Caller
ID number auto edit.
I cannot dial the phone number
edited in the caller list.
R The phone number you dialed might have been edited
incorrectly (for example, the long distance “1” or the area
code is missing). Edit the phone number with another
pattern (page 44).
Time on the unit has shifted.
R Incorrect time information from incoming Caller ID
changes the time. Set the time adjustment to
“Manual” (off) (page 36).
The 2nd caller’s information is
not displayed during an outside
call.
R In order to use Caller ID, call waiting, or Call Waiting
Caller ID (CWID), you must first contact your service
provider/telephone company and subscribe to the desired
service.
After subscribing, you may need to contact your service
provider/telephone company again to activate this specific
service, even if you already subscribed to both Caller ID
and Call Waiting with Caller ID services (CWID).
66
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p66
66
2011/11/21
12:02:15
Useful Information
Using Bluetooth devices
Problem
Cause/solution
I cannot copy phonebook
entries from a cellular phone.
R Confirm that the cellular phone supports Bluetooth
wireless technology.
R Confirm that the cellular phone supports the Phone Book
Access Profile (PBAP) or Object Push Profile (OPP)
specification.
R If the cellular phone is already connected to another
Bluetooth device such as a Bluetooth headset, turn it off
or disconnect it from the cellular phone.
R Someone is using a cellular line or headset. Try again
later.
R Turn the cellular phone off, then turn it on and try again.
R If an entry is already stored in the unit’s shared
phonebook, the entry cannot be copied even by selecting
another group.
I cannot have a conversation
using the headset.
R Your Bluetooth headset is not registered. Register it
(page 47).
R Turn your headset off, then turn it on and try again.
Noise is heard during a call on
the headset.
R A Bluetooth headset can communicate with the base unit
within a range of approximately 10 m (33 feet). The
connection may be subject to interference from
obstructions such as walls or electronic devices. Move
closer to the base unit.
I cannot connect my headset to
the base unit.
R Confirm that your headset is turned on.
R If your headset is already connected to another Bluetooth
device such as your cellular phone, disconnect the
headset from your cellular phone, then perform the
connecting procedure from the base unit.
R If someone is using a cellular line, you cannot connect the
headset. There can be only one active Bluetooth
connection at a time.
R The headset has not been registered to the base unit.
Register the headset (page 47).
Some headset enhanced
features are not available.
R The base unit does not support enhanced features such
as Last number redial or Call reject.
An error tone is heard when I
try to program the Bluetooth
feature.
R The Bluetooth feature cannot be accessed immediately
after connecting the AC adaptor to the base unit. Wait a
few seconds and try again.
R The headset has not connected to the base unit yet, even
though you performed the connecting procedure setting.
Wait a few seconds and try again.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p67
67
2011/11/21
12:02:15
67
Useful Information
Answering system
Problem
Cause/solution
The unit does not record new
messages.
R The answering system is turned off. Turn it on (page 49).
R The answering system does not answer or record calls
from cellular lines.
R The message memory is full. Erase unnecessary
messages (page 50).
R The recording time is set to “Greeting only”. Change
the setting (page 53).
R If you subscribe to a voice mail service, messages are
recorded by your service provider/telephone company,
not your telephone. Change the unit’s number of rings
setting or contact your service provider/telephone
company (page 53).
R The answering system will not answer incoming calls
while:
– the base unit or 2 or more handsets are on a cellular
call or an intercom call.
– a headset is in use.
Caller information is recorded in the caller list.
I cannot operate the answering
system remotely.
R The remote access code is not set. Set the remote
access code (page 51).
R You are entering the wrong remote access code. If you
have forgotten your remote access code, enter the
remote access code setting to check your current code
(page 51).
R The answering system is turned off. Turn it on (page 52).
R You cannot operate the answering system when calling a
cellular phone registered to the base unit.
Bluetooth PIN
Problem
Cause/solution
I cannot remember the PIN.
R Change the PIN using the following method.
1
2
3
4
68
MMENUN#619
*7000
Enter the new 4-digit PIN. a MOKN
Enter the new 4-digit PIN again. a MSAVEN a MOFFN
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p68
68
2011/11/21
12:02:15
Useful Information
Liquid damage
Problem
Cause/solution
Liquid or other form of moisture
has entered the handset/base
unit.
R Disconnect the AC adaptor and telephone line cord from
the base unit. Remove the batteries from the handset and
leave to dry for at least 3 days. After the handset/base
unit are completely dry, reconnect the AC adaptor and
telephone line cord. Insert the batteries and charge fully
before use. If the unit does not work properly, contact an
authorized service center.
Caution:
R To avoid permanent damage, do not use a microwave oven to speed up the drying process.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p69
69
2011/11/21
12:02:16
69
Useful Information
FCC and other information
This equipment complies with Part 68 of the
FCC rules and the requirements adopted by
the ACTA. On the bottom of this equipment
is a label that contains, among other
information, a product identifier in the
format US:ACJ----------.
If requested, this number must be provided
to the telephone company.
L Registration No.............(found on the
bottom of the unit)
L Ringer Equivalence No. (REN).......0.1B
advised of your right to file a complaint with
the FCC if you believe it is necessary.
A plug and jack used to connect this
equipment to the premises wiring and
telephone network must comply with the
applicable FCC Part 68 rules and
requirements adopted by the ACTA. A
compliant telephone cord and modular plug
is provided with the product. It is designed
to be connected to a compatible modular
jack that is also compliant.
If trouble is experienced with this
equipment, for repair or warranty
information, please contact a Factory
Service Center or other Authorized Servicer.
If the equipment is causing harm to the
telephone network, the telephone company
may request that you disconnect the
equipment until the problem is resolved.
The REN is used to determine the number
of devices that may be connected to a
telephone line. Excessive RENs on a
telephone line may result in the devices not
ringing in response to an incoming call. In
most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain
of the number of devices that may be
connected to a line, as determined by the
total RENs, contact the local telephone
company. For products approved after July
23, 2001, the REN for the product is part of
the product identifier that has the format
US:AAAEQ##TXXXX. The digits
represented by ## are the REN without a
decimal point (e.g., 03 is a REN of 0.3).
If this equipment causes harm to the
telephone network, the telephone company
will notify you in advance that temporary
discontinuance of service may be required.
But if advance notice isn't practical, the
telephone company will notify the customer
as soon as possible. Also, you will be
70
The telephone company may make changes
in its facilities, equipment, operations or
procedures that could affect the operation of
the equipment. If this happens the
telephone company will provide advance
notice in order for you to make necessary
modifications to maintain uninterrupted
service.
Connection to party line service is subject to
state tariffs. Contact the state public utility
commission, public service commission or
corporation commission for information.
If your home has specially wired alarm
equipment connected to the telephone line,
ensure the installation of this equipment
does not disable your alarm equipment. If
you have questions about what will disable
alarm equipment, consult your telephone
company or a qualified installer.
This equipment is hearing aid compatible as
defined by the FCC in 47 CFR Section
68.316.
When you hold the phone to your ear, noise
might be heard in your Hearing Aid. Some
Hearing Aids are not adequately shielded
from external RF (radio frequency) energy. If
noise occurs, use an optional headset
accessory or the speakerphone option (if
applicable) when using this phone. Consult
with your audiologist or Hearing Aid
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p70
70
2011/11/21
12:02:16
Useful Information
manufacturer about the availability of
Hearing Aids which provide adequate
shielding to RF energy commonly emitted
by digital devices.
WHEN PROGRAMMING EMERGENCY
NUMBERS AND(OR) MAKING TEST
CALLS TO EMERGENCY NUMBERS:
1) Remain on the line and briefly explain to
the dispatcher the reason for the call.
2) Perform such activities in the off-peak
hours, such as early morning or late
evenings.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Privacy of communications may not be
ensured when using this phone.
CAUTION:
Any changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate this device.
NOTE:
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced
radio/TV technician for help.
Some cordless telephones operate at
frequencies that may cause interference to
nearby TVs and VCRs. To minimize or
prevent such interference, the base of the
cordless telephone should not be placed
near or on top of a TV or VCR. If
interference is experienced, move the
cordless telephone further away from the TV
or VCR. This will often reduce or eliminate
interference.
FCC RF Exposure Warning:
L This product complies with FCC radiation
exposure limits set forth for an
uncontrolled environment.
L To comply with FCC RF exposure
requirements, the base unit must be
installed and operated 20 cm (8 inches)
or more between the product and all
person’s body (excluding extremities of
hands, wrist and feet).
L This product may not be collocated or
operated in conjunction with any other
antenna or transmitter.
L The handset may be carried and operated
with only the specific provided belt-clip.
Other non-tested belt-clips or similar
body-worn accessories may not comply
and must be avoided.
Notice
L FCC ID can be found inside the battery
compartment or on the bottom of the
units.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p71
71
2011/11/21
12:02:16
71
Useful Information
Compliance with TIA-1083 standard:
Telephone handsets identified with this logo
have reduced noise and interference when
used with T-Coil equipped hearing aids and
cochlear implants.
Compatible with
Hearing Aid T-Coil
T
TIA-1083
72
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p72
72
2011/11/21
12:02:16
Guía Rápida Española
Guía Rápida Española
Instalación
Unidad base
L Use solo el adaptador de corriente Panasonic PNLV226 incluido.
“Clic”
Oprima firmemente
el contacto.
Correcto
Incorrecto
Gancho
A la toma de
corriente
A la toma de
teléfono de línea
única (RJ11C)
Filtro DSL/ADSL*
*Requiere un filtro DSL/ADSL (no incluido) si tiene este tipo de servicio.
Auricular
L UTILICE SOLO baterías de Ni-MH tamaño AAA (R03).
L NO utilice baterías Alcalinas, de Manganeso o de Ni-Cd.
L Compruebe que las polaridades son las correctas (S, T).
SOLO baterías Ni-MH recargables
“Clic”
CARGUE
APROXIMADAMENTE
DURANTE 7 HORAS
Confirme que
aparezca
“Cargando”.
Cargador
A la toma de corriente
L Use solo el adaptador de
corriente Panasonic
PNLV226 incluido.
Para obtener ayuda, visite http://www.panasonic.com/help (solo en ingls)
TG7731_41_(en-en)_1121_ver.021.p73
73
2011/11/21
12:02:16
73
Guía Rápida Española
Sugerencias de operación
Teclas de función
El auricular incluye 3 teclas de función. Al oprimir una tecla de
función, puede seleccionar la función que aparece directamente
encima de ella en la pantalla.
{C}, {MENU}, {CEL.} y otras funciones adicionales se
asignan a las teclas de función. Preste atención a la pantalla
para ver qué funciones están asignadas a las teclas de función
durante la operación del auricular.
Tecla de volumen
Oprima {+} o {-} repetidamente para ajustar el volumen del
receptor o del altavoz mientras habla.
Tecla navegadora
{^}, {V}, {<}, o {>}: Navegue por diversas listas y
elementos.
{<} CID (identificador de llamadas): Vea la lista de personas
que llamaron.
{>} REDIAL (Remarcación): Vea la lista de remarcación.
CEL.
VO
L.
SP-PHONE
CA LL W A IT
FL A SH /
CID
REDIAL
{^}
{<}
{>}
{V}
Cambio de idiomas (predeterminado: “English”) (Auricular)
Cuando instale las baterías por primera vez, es posible que aparezca “Date and time Press SELECT”.
Oprima {OFF} para salir.
Idioma de la pantalla
{MENU} (11) s {r}: “Español” s {GUARDA} s {OFF}
Idioma de la guía de voz
{MENU} (112 s {r}: “Español” s {GUARDA} s {OFF}
Fecha y hora (Auricular)
1
2
3
4
{MENU} (1)1
Introduzca el día, mes y año actuales. s {OK}
Introduzca la hora y minuto actuales (formato de reloj de 24 horas).
{GUARDA} s {OFF}
Cómo grabar el mensaje de saludo del contestador de llamadas para
la línea terrestre (Auricular)
Si utiliza un mensaje de saludo pregrabado, no es necesario que grabe su propio mensaje de saludo.
1 {MENU} (3)2 s {r}: “Sí” s {SELEC.}
2 Después de que suene un pitido, sostenga el auricular a una distancia aproximada de 20 cm (8
pulgadas) y hable con claridad en el micrófono (máx. de 2 minutos).
3 Oprima {ALTO} para dejar de grabar. s {OFF}
74
Para obtener ayuda, visite http://www.panasonic.com/help (solo en ingls)
TG7731_41_(en-en)_1121_ver.021.p74
74
2011/11/21
12:02:16
Guía Rápida Española
Enlace a celular
Puede usar la unidad para hacer o contestar llamadas usando una línea de teléfono celular. Sus teléfonos
celulares deben tener tecnología inalámbrica Bluetooth® compatible con este producto. Para obtener más
detalles, visite nuestro sitio web: http://www.panasonic.com/link2cell
L Coloque su teléfono celular cerca de la unidad base. Si su teléfono celular está demasiado cerca de la
unidad base durante la llamada celular, es posible que escuche ruido. Para un mejor funcionamiento, le
recomendamos que coloque su teléfono celular de 0.6 m a 3 m (2 pies a 10 pies) de la unidad base.
Línea celular
Proveedor de servicio
del teléfono celular
Cómo registrar un teléfono celular con Bluetooth
1
Auricular:
Para CELL 1: {MENU} (6241
Para CELL 2: {MENU} (6242
L Después de que el indicador de CELL 1 o CELL 2 comience a parpadear en rojo en la unidad base, el
resto del procedimiento debe completarse en menos de 5 minutos.
2 Su teléfono celular:
Mientras el indicador de CELL 1 o CELL 2 está parpadeando en rojo, siga las instrucciones de su teléfono
celular para entrar al modo de registro.
L Dependiendo de su teléfono celular, es posible que le pida que introduzca el NIP de la unidad base
(predeterminado: “0000”).
3 Auricular:
Espere a que se emita un pitido largo.
L Es posible que tarde más de 10 segundos en completar el registro.
L Cuando el indicador de CELL 1 o CELL 2 se ilumina en verde, esto significa que el teléfono celular está
conectado a la unidad base. Ya está listo para hacer llamadas regulares de celular.
4 Para seleccionar qué unidad recibe llamadas para la línea celular (predeterminado: “Todo”):
{OK} s {r}: Seleccione el auricular deseado o “Todo”. s {GUARDA}
L Si no se requiere, vaya al paso 5.
5 {OFF}
Nota:
L Asegúrese de que su teléfono celular está configurado para conectar este producto automáticamente.
Consulte las instrucciones de operación de su teléfono celular.
Marcas registradas
L La marca denominativa y los logotipos de Bluetooth® son propiedad de Bluetooth SIG, Inc. y cualquier uso
de dichas marcas por parte de Panasonic Corporation se hace bajo licencia. Todas las demás marcas
comerciales que se identifican en el presente pertenecen a sus respectivos propietarios.
Para obtener ayuda, visite http://www.panasonic.com/help (solo en ingls)
TG7731_41_(en-en)_1121_ver.021.p75
75
2011/11/21
12:02:16
75
Guía Rápida Española
Enlace a celular
Unidad base: Indicadores CELL 1/CELL 2
Estado
Significado
Verde (encendido)
Un teléfono celular está conectado. Listo para hacer o recibir llamadas
celulares.
Verde (parpadea)
La línea del celular se está usando.
Las entradas del directorio telefónico se están copiando desde un teléfono
celular.
Verde
(parpadea rápidamente)
Se está recibiendo una llamada de celular.
Ámbar (encendido)
No hay un teléfono celular conectado a la unidad base.
Ámbar
(parpadea rápidamente)
La unidad base está buscando el teléfono celular registrado.
Rojo (parpadea)
Una llamada de celular se pone en espera.
Luz apagada
No hay un teléfono celular registrado en la unidad base.
Auricular: enlace a elementos de la pantalla del celular
t
Se está usando una línea de celular.
L Cuando parpadea: La llamada de celular se pone en espera.
L Cuando parpadea rápidamente: Se está recibiendo una llamada de celular.
]12
Un teléfono celular está conectado.*1 Listo para hacer o recibir llamadas celulares.
L Cuando está apagado: No hay un teléfono celular conectado a la unidad base.
*1 La línea o líneas celulares correspondientes se indican enseguida del elemento.
uv
Está recibiendo una llamada de celular en esa línea.
Cómo conectar o desconectar el teléfono celular
Conexión automática al teléfono celular
La unidad se conecta al teléfono celular a intervalos regulares si se pierde la conexión. Consulte las
instrucciones de operación para cambiar el intervalo (predeterminado: “1 min” ).
L Cuando está usando una línea celular o un audífono con Bluetooth, la unidad base pierde la conexión de
otros dispositivos con Bluetooth (teléfono celular o audífono). Para restablecer la conexión a los teléfonos
celulares automáticamente, deje encendida la conexión automática.
Cómo conectar o desconectar manualmente el teléfono celular
Cuando haga o conteste llamadas con su teléfono celular, le recomendamos que lo desconecte de la unidad
base; de lo contrario, es posible que no escuche el audio que reciba en su teléfono celular.
También puede reconectar manualmente el teléfono celular a la unidad base sin esperar a que la función de
conexión automática reanude la conexión.
1 Para conectarlo o desconectarlo:
Para CELL 1: {MENU} (6251 (suena un pitido largo.)
Para CELL 2: {MENU} (6252 (suena un pitido largo.)
2 {OFF}
76
Para obtener ayuda, visite http://www.panasonic.com/help (solo en ingls)
TG7731_41_(en-en)_1121_ver.021.p76
76
2011/11/21
12:02:16
Guía Rápida Española
Enlace a celular
Modo exclusivo para la línea celular (si no utiliza la línea terrestre)
Si no utiliza la línea terrestre, configure el modo exclusivo para la línea celular para usar esta unidad en forma
más conveniente.
1 {MENU} (157
2 Para encenderlo: {r}: “Encendido” s {SELEC.} s {r}: “Sí” s {SELEC.}
Para apagarlo: {r}: “Apagado” s {SELEC.}
Operaciones básicas
Cómo hacer y contestar llamadas (Auricular)
Para hacer llamadas de celular
1
2
Marque el número telefónico. s {CEL.}
L Cuando el modo exclusivo para la línea celular está configurado,
también puede oprimir {C}/{s} en lugar de {CEL.}.
L Cuando solo hay 1 teléfono celular registrado, la unidad comienza
a marcar.
Cuando hay 2 teléfonos celulares registrados:
{r}: Seleccione el teléfono celular deseado. s {SELEC.}
Para hacer llamadas por la línea
terrestre
Marque el número telefónico. s {C}/{s}
Para contestar llamadas
{C}/{s}
Para colgar
{OFF}
Para ajustar el volumen del
receptor o del altavoz
Oprima {+} o {-} repetidamente mientras habla.
Cómo hacer una llamada usando
la lista de remarcación
1
2
{>} REDIAL s {r}: Seleccione el número telefónico deseado.
Para hacer una llamada celular:
Cuando solo hay 1 teléfono celular registrado: {CEL.}
o
Cuando hay 2 teléfonos celulares registrados:
{CEL.} s {r}: Seleccione el teléfono celular deseado. s {SELEC.}
Para hacer una llamada terrestre:
{C}
Cómo hacer y contestar llamadas (Unidad base: Serie KX-TG7741)
Para hacer llamadas de celular
{CELL 1}/{CELL 2} s Marque el número telefónico.
L Cuando el modo exclusivo para la línea celular está configurado,
también puede oprimir {SP-PHONE} en lugar de {CELL 1}/{CELL 2}.
Para hacer llamadas por la línea
terrestre
{SP-PHONE} s Marque el número telefónico.
Para contestar llamadas
{SP-PHONE}
Para colgar
{SP-PHONE}
Para ajustar el volumen del
altavoz
Oprima {+} o {-} repetidamente mientras habla.
Para obtener ayuda, visite http://www.panasonic.com/help (solo en ingls)
TG7731_41_(en-en)_1121_ver.021.p77
77
2011/11/21
12:02:16
77
Guía Rápida Española
Operaciones básicas
Cómo hacer y contestar llamadas (Unidad base: Serie KX-TG7741)
Remarcación del último número
marcado
1
2
Para hacer una llamada celular: {CELL 1}/{CELL 2}
Para hacer una llamada terrestre: {SP-PHONE}
{REDIAL}
Para ajustar el volumen del timbre (Auricular)
Para ajustar el volumen del timbre
del auricular (línea de celular)
Para ajustar el volumen del timbre
del auricular (línea terrestre)
Para ajustar el volumen del timbre
de la unidad base (línea celular)
Para ajustar el volumen del timbre
de la unidad base (línea terrestre)
1
2
1
2
1
2
1
2
Para CELL 1: {MENU} (6281
Para CELL 2: {MENU} (6282
{r}: Seleccione el volumen deseado. s {GUARDA} s {OFF}
{MENU} (16)
{r}: Seleccione el volumen deseado. s {GUARDA} s {OFF}
Para CELL 1: {MENU} (*6281
Para CELL 2: {MENU} (*6282
{r}: Seleccione el volumen deseado. s {GUARDA} s {OFF}
{MENU} (*16)
{r}: Seleccione el volumen deseado. s {GUARDA} s {OFF}
Directorio telefónico compartido (Auricular)
Para añadir entradas
Para hacer llamadas
1
2
3
4
1
2
{C} s {AÑAD.}
Introduzca el nombre de la persona (máx. 16 caracteres). s {OK}
Introduzca el número telefónico de la persona (máx. 24 dígitos). s
{OK}
{r}: Seleccione el grupo deseado. s {SELEC.} 2 veces s {OFF}
{C} s {r}: Seleccione la entrada deseada.
Para hacer una llamada celular:
Cuando solo hay 1 teléfono celular registrado: {CEL.}
o
Cuando hay 2 teléfonos celulares registrados:
{CEL.} s {r}: Seleccione el teléfono celular deseado. s {SELEC.}
Para hacer una llamada terrestre:
{C}
Contestador de llamadas de la línea terrestre (Unidad base)
Contestador encendido/apagado
Oprima {ANSWER ON/OFF} para encender y apagar el contestador de
llamadas.
Para escuchar mensajes
{6} (PLAY)
Contestador de llamadas de la línea terrestre (Auricular)
Para escuchar mensajes
78
Para escuchar mensajes nuevos:
{MENU} (323
Para escuchar todos los mensajes:
{MENU} (324
Para obtener ayuda, visite http://www.panasonic.com/help (solo en ingls)
TG7731_41_(en-en)_1121_ver.021.p78
78
2011/11/21
12:02:16
Guía Rápida Española
Cómo usar dispositivos Bluetooth
Copiado de entradas del directorio telefónico desde un teléfono celular con Bluetooth (transferencia
del directorio telefónico)
Puede copiar entradas del directorio telefónico desde los teléfonos celulares registrados o desde otros
teléfonos celulares (no registrados) al directorio telefónico compartido de la unidad.
1 Auricular: {MENU} (618
2 Auricular:
Para copiar desde teléfonos celulares registrados:
{r}: Seleccione el teléfono celular deseado. s {SELEC.}
L Los elementos copiados se almacenan en el grupo (“Cel. 1” o “Cel. 2”) en el que está registrado
el teléfono celular.
Para copiar desde otros teléfonos celulares (no registrados):
{r}: “Otro celular” s {SELEC.} s {r}: Seleccione el grupo al que desea copiar. s {SELEC.}
3 Cuando aparezca “Transf. datos del directorio del celular” : Vaya al paso 4.
Cuando aparezca el menú “Selec. modo” :
{r}: Seleccione “Auto” o “Manual”. s {SELEC.}
“Auto”: Descargue todas las entradas del teléfono celular automáticamente. Vaya al paso 5.
“Manual”: Copie las entradas que seleccionó.
L El menú “Selec. modo” aparece solo cuando el teléfono celular soporta PBAP (Perfil de Acceso a
Directorio Telefónico) para la conexión Bluetooth.
4 Teléfono celular:
Siga las instrucciones de su teléfono celular para copiar las entradas del directorio telefónico.
L Para otros teléfonos celulares (no registrados), necesita buscar y seleccionar la unidad base. Es
posible que requiera el NIP de la unidad base (predeterminado: “0000”).
L Las entradas que se están copiando aparecen en el auricular.
5 Auricular:
Espere a que aparezca “Completo”. s {OFF}
Para obtener ayuda, visite http://www.panasonic.com/help (solo en ingls)
TG7731_41_(en-en)_1121_ver.021.p79
79
2011/11/21
12:02:16
79
Guía Rápida Española
Cómo usar dispositivos Bluetooth
Cómo usar un audífono Bluetooth (opcional) para llamadas por la línea terrestre
Al registrar un audífono Bluetooth en la unidad base, podrá tener conversaciones inalámbricas a manos
libres para llamadas por la línea terrestre.
L La conexión del audífono con Bluetooth no está disponible mientras alguien se encuentra usando la línea
celular.
Cómo registrar un audífono en la unidad base
1
2
3
4
Su audífono:
Configure su audífono en modo de registro.
L Consulte las instrucciones de operación de su audífono.
Auricular:
{MENU} (621
Registre usando el auricular.
Registro
Introduzca el NIP de su audífono.
L Por lo general, el NIP predeterminado es “0000”. Consulte las instrucciones de operación del
audífono.
Oprima {OK}, y después espere a que se emita un pitido largo. s {OFF}
L Cuando el indicador HEADSET de la unidad base se ilumina en verde, usted está listo para usar el
audífono.
Cómo operar un audífono inalámbrico con Bluetooth usando una línea terrestre
Consulte las instrucciones de operación de su audífono para ver cómo funciona.
N Cómo contestar llamadas de la línea terrestre con su audífono
Para contestar una llamada de línea terrestre, encienda su audífono. Para ello, consulte las instrucciones
de operación de su audífono.
Cuando termine de hablar, apague su audífono. Para ello, consulte las instrucciones de operación de su
audífono.
L Si no puede colgar la llamada usando su audífono;
oprima { } (STOP) en la unidad base. (serie KX-TG7731)
oprima {SP-PHONE} en la unidad base 2 veces. (serie KX-TG7741)
N Cómo cambiar entre la unidad base y su audífono
Puede cambiar entre la unidad base y su audífono:
durante una llamada por una línea terrestre con el altavoz de la unidad base. (serie KX-TG7741)
durante una llamada de intercomunicador entre la unidad base y el auricular. (serie KX-TG7741)
mientras escucha los mensajes grabados en el contestador de llamadas de la unidad base.*1
Serie KX-TG7741
Para cambiar a su audífono:
Oprima {HEADSET} en la unidad base.
Para cambiar a la unidad base:
Oprima {SP-PHONE} en la unidad base.
*1 Serie KX-TG7731
L Solo puede cambiar entre la unidad base y su audífono. Encienda el audífono. Para ello, consulte las
instrucciones de operación de su audífono.
80
Para obtener ayuda, visite http://www.panasonic.com/help (solo en ingls)
TG7731_41_(en-en)_1121_ver.021.p80
80
2011/11/21
12:02:16
Guía Rápida Española
Preguntas frecuentes
Pregunta
Causa y solución
¿Por qué aparece _?
L El auricular está demasiado lejos de la unidad base. Acérquelo.
L El adaptador para corriente de la unidad base no está conectado
correctamente. Conecte de nuevo el adaptador para corriente a la unidad
base.
L El auricular no está registrado en la unidad base. Regístrelo.
1 Auricular: {MENU} (13)
2 Unidad base: Oprima y mantenga oprimido {LOCATOR} durante
aproximadamente 5 segundos hasta que suene el tono de registro.
3 Auricular: Oprima {OK}, y después espere hasta que suene un
pitido largo.
¿Por qué no es posible
registrar un teléfono celular a
la unidad base?
L Dependiendo de la compatibilidad del teléfono celular, es posible que no
pueda registrarlo en la unidad base. Para obtener más información, visite
http://www.panasonic.com/link2cell
L Confirme que la función de Bluetooth de su teléfono celular esté
encendida. Es posible que necesite encender esta función dependiendo
de su teléfono celular.
¿Por qué no es posible
escuchar el tono de
marcación? (línea de celular)
L Asegúrese de que la luz indicadora de CELL 1 o CELL 2 se ilumine en
verde y de que el teléfono celular esté conectado a la unidad base.
L El teléfono celular no se ha registrado en la unidad base. Regístrelo.
¿Cómo se incrementa el nivel
de volumen del auricular?
L Oprima la tecla de volumen {+} repetidamente mientras habla.
¿Por qué hay ruido o se corta
la conversación?
L Trate de reubicar la unidad base de forma que se minimice la distancia al
auricular.
L Si ocurre el mismo problema aunque el auricular se encuentre enseguida
de la unidad base, llame a soporte al cliente de Panasonic al 1-800-211PANA (1-800-211-7262).
¿Es posible añadir otro
auricular accesorio a mi
unidad base?
L Sí, puede añadir hasta 6 auriculares (incluyendo los que se venden con
su unidad base) a una sola unidad base.
L Para adquirir auriculares accesorios adicionales (KX-TGA470), visite
http://www.panasonic.com
o llame al 1-800-332-5368. Los usuarios TTY (usuarios con
impedimentos auditivos o del habla) pueden llamar al 1-866-605-1277.
¿Es posible mantener
cargando las baterías todo el
tiempo?
L Puede dejar el auricular en la unidad base o el cargador en cualquier
momento. Esto no daña las baterías.
¿Cómo se contestan las
llamadas en espera (segunda
llamada)?
L Oprima {CALL WAIT} cuando escuche el tono de llamada en espera.
Para obtener más información acerca del registro, visite
http://www.panasonic.com/RegisterYourHandset (solo en inglés)
Para obtener ayuda, visite http://www.panasonic.com/help (solo en ingls)
TG7731_41_(en-en)_1121_ver.021.p81
81
2011/11/21
12:02:16
81
Appendix
Customer services
Customer Services Directory (United States and Puerto Rico)
Obtain Product Information and Operating Assistance; locate your nearest
Dealer or Service Center; purchase Parts and Accessories; or make Customer
Service and Literature requests by visiting our Web Site at:
http://www.panasonic.com/help
or, contact us via the web at:
http://www.panasonic.com/contactinfo
You may also contact us directly at: 1-800-211-PANA (1-800-211-7262),
Monday - Friday 9 am to 9 pm; Saturday - Sunday 10 am to 7 pm, EST.
TTY users (hearing or speech impaired users) can call 1-877-833-8855.
Accessory Purchases (United States and Puerto Rico)
Purchase Parts, Accessories and Instruction Books online for all
Panasonic Products by visiting our Web Site at:
http://www.pstc.panasonic.com
or, send your request by E-mail to:
npcparts@us.panasonic.com
You may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only)
(Monday - Friday 9 am to 9 pm, EST.)
Panasonic Service and Technology Company
20421 84th Avenue South, Kent, WA 98032
(We Accept Visa, MasterCard, Discover Card, American Express, and
Personal Checks.)
TTY users (hearing or speech impaired users) can call 1-866-605-1277.
82
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p82
82
2011/11/21
12:02:16
Appendix
Warranty (For United States and Puerto Rico)
PANASONIC CORPORATION OF NORTH AMERICA
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic Telephone Products
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship,
Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length
of the period indicated on the chart below, which starts with the date of original purchase
(“Limited Warranty period”), at its option either (a) repair your product with new or
refurbished parts, or (b) replace it with a new or a refurbished product. The decision to
repair or replace will be made by the warrantor.
Parts
Labor
One (1) Year
One (1) Year
During the “Labor” Limited Warranty period there will be no charge for labor. During the
“Parts” Limited Warranty period, there will be no charge for parts. You must mail-in your
product prepaid during the Limited Warranty period. This Limited Warranty excludes both
parts and labor for batteries, antennas, and cosmetic parts (cabinet). This Limited Warranty
only applies to products purchased and serviced in the United States or Puerto Rico. This
Limited Warranty is extended only to the original purchaser and only covers products
purchased as new.
Ship-In Service
For assistance in the continental United States and Puerto Rico in obtaining repairs please
ship the product prepaid to:
PSTC (Panasonic) Exchange Center,
4900 George McVay Drive, Suite B Door #12, McAllen, TX 78503
panacare@us.panasonic.com
When shipping the unit carefully pack in a padded shipping carton, include all
accessories, and send it prepaid. Include a letter detailing the complaint, a return
address and provide a day time phone number where you can be reached. P.O. Boxes
are not acceptable. Keep the tracking number for your records. A copy of valid registered
receipt is required under the 1 year parts and labor Limited Warranty.
For Limited Warranty service for headsets if a headset is included with this
product please follow instructions above.
IF REPAIR IS NEEDED DURING THE LIMITED WARRANTY PERIOD THE
PURCHASER WILL BE REQUIRED TO FURNISH A SALES
RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE,
AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE
CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH
PROOF OF PURCHASE.
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p83
83
2011/11/21
12:02:16
83
Appendix
Limited Warranty Limits And Exclusions
This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship,
and DOES NOT COVER normal wear and tear or cosmetic damage. The Limited Warranty
ALSO DOES NOT COVER damages which occurred in shipment, or failures which are
caused by products not supplied by the warrantor, or failures which result from accidents,
misuse, abuse, neglect, bug infestation, mishandling, misapplication, alteration, faulty
installation, set-up adjustments, misadjustment of consumer controls, improper
maintenance, power line surge, lightning damage, modification, introduction of sand,
humidity or liquids, commercial use such as hotel, office, restaurant, or other business or
rental use of the product, or service by anyone other than a Factory Service Center or
other Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED
WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR
ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY. (As examples, this
excludes damages for lost time, lost calls or messages, cost of having someone remove or
re-install an installed unit if applicable, travel to and from the servicer. The items listed are
not exclusive, but are for illustration only.) ALL EXPRESS AND IMPLIED WARRANTIES,
INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE
PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, or limitations on how long an implied warranty lasts, so the exclusions may not
apply to you.
This Limited Warranty gives you specific legal rights and you may also have other rights
which vary from state to state. If a problem with this product develops during or after the
Limited Warranty period, you may contact your dealer or Service Center. If the problem is
not handled to your satisfaction, then write to the warrantor’s Consumer Affairs
Department at the addresses listed for the warrantor.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY,
ARE YOUR RESPONSIBILITY.
When you ship the product
L Carefully pack your unit, preferably in the original carton.
L Attach a letter, detailing the symptom.
L Send the unit to PSTC (Panasonic) Exchange Center, prepaid and adequately insured.
L Do not send your unit to Panasonic Corporation of North America listed on the back
cover or to executive or regional sales offices. These locations do not repair consumer
products.
84
For assistance, please visit http://www.panasonic.com/help
TG7731_41_(en-en)_1121_ver.021.p84
84
2011/11/21
12:02:16
Index
E
Index
#
A
B
C
D
3-way conference: 25, 29
Additional handset: 42
Alarm: 40
Answering calls: 23, 27
Answering system
Call screening: 49
Erasing messages: 50, 51, 52
Greeting message: 50
Greeting only: 53
Listening to messages: 50, 52
Number of rings: 53
Recording time: 53
Remote access code: 51
Remote operation: 51
Ring count: 53
Toll saver: 53
Turning on/off: 49, 52
Auto talk: 23, 38
Battery: 11, 12
Belt clip: 15
Bluetooth wireless technology
Cellular phone (Link to cell): 18
Headset: 47
Phonebook transfer: 46
Booster (Clarity booster): 24
Call block: 41
Call share: 24, 29
Call waiting: 24, 28
Call Waiting Caller ID: 24
Caller ID number auto edit: 38, 44
Caller ID service: 43
Caller list: 44
Caller list edit: 44
Cellular calls: 22, 27
Cellular phone
Deregistration: 21
Registration: 18
Chain dial: 32
CID (Caller ID): 44
Conference calls: 58
Control type: 15
Customer support: 38
Date and time: 17
Dialing mode: 17
Direct command code: 33
Display
Contrast: 37
Language: 17
F
G
H
I
K
L
M
P
R
S
T
V
Eco mode: 13
Equalizer: 24
Error messages: 61
Flash: 24, 28
Groups: 30, 43
Handset
Deregistration: 42
Locator: 57
Name: 40
Registration: 42
Hold: 23, 28
Intercom: 57
Key tone: 37
Landline calls: 22, 27
Line mode: 38
Link to cell
Area code: 21
Auto connection: 19
Cellular line only mode: 20
Cellular line selection: 20
Connection: 20
Ring as cell mode: 19
Select unit to ring: 19
Making calls: 22, 27
Missed calls: 43
Mute: 24, 28
Pause: 22, 27
Phonebook: 30
PIN: 21
Power failure: 12
Redialing: 22, 27
Ringer ID: 43
Ringer tone: 35, 37, 43
Rotary/pulse service: 24
Silent mode: 40
SP-PHONE (Speakerphone): 22
Talking Caller ID: 43
Temporary tone dialing: 24, 29
Time adjustment: 36
Transferring calls: 58
Troubleshooting: 62
TTY: 82
VM (Voice mail): 55
Voice guidance language: 17
Voice mail: 53, 55
Volume
Receiver: 22
Ringer (Base unit): 28, 35, 37
Ringer (Handset): 23, 35, 37
Speaker: 22, 27
85
TG7731_41_(en-en)_1121_ver.021.p85
85
2011/11/21
12:02:16
Index
W
Wall mounting: 59
86
TG7731_41_(en-en)_1121_ver.021.p86
86
2011/11/21
12:02:16
Notes
87
TG7731_41_(en-en)_1121_ver.021.p87
87
2011/11/21
12:02:16
IMPORTANT!
If your product is not working properly. . .
1 Reconnect AC adaptor to the base unit.
2 Check if telephone line cord is connected.
3 Use rechargeable Ni-MH batteries.
(Alkaline/Manganese/Ni-Cd batteries CANNOT be used.)
4 Read troubleshooting page in the Operating Instructions.
Visit our Web site: http://www.panasonic.com/help
L FAQ and troubleshooting hints are available.
For your future reference
We recommend keeping a record of the following information to assist with any repair under
warranty.
Serial No.
Date of purchase
(found on the bottom of the base unit)
Name and address of dealer
Attach your purchase receipt here.
One Panasonic Way, Secaucus, New Jersey 07094
© Panasonic System Networks Co., Ltd. 2011
*TG7731*
Printed in China
*TG7731*
PNQX5106ZA
TG7731_41_(en-en)_1121_ver.021.p88
88
2011/11/21
TT1111MG0 (D)
12:02:16
Download PDF

advertising