Compaq 55 Computer Monitor User Manual

Notice
The information in this guide is subject to change without notice.
COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE
FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS
CONTAINED HEREIN; NOR FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE
FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.
This guide contains information protected by copyright. No part of this
guide may be photocopied or reproduced in any form without prior
written consent from Compaq Computer Corporation.
 1997 Compaq Computer Corporation.
All rights reserved. Printed in the U.S.A.
Compaq, Deskpro, and QVision are registered in the U. S. Patent and
Trademark Office.
Microsoft, MS-DOS, Windows, Windows NT, and other names of
Microsoft products referenced herein are trademarks or registered
trademarks of Microsoft Corporation.
Product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies.
The software described in this guide is furnished under a license
agreement or nondisclosure agreement. The software may be used or
copied only in accordance with the terms of the agreement.
User’s Guide
Compaq V55 Color Monitor
First Edition (November 1997)
Part Number 308012-001
Compaq Computer Corporation
Writer: Marianne Silvetti Saved By: Marianne Silvetti Saved Date: 10/10/97 10:50 AM
Pages: 1 Words: 180 Template: c:\msoffice\templates\commnoti.dot
File Name ANotice.doc Part Number 308012-001
308012-001
book
1
E NGLISH
Introduction
The Compaq V55 Color Monitor is a microprocessor-based,
intelligent scanning monitor that automatically locks in on the
most common display modes. This monitor operates most
efficiently when used with a Compaq compatible graphics
controller.
Product Features
The monitor features include the following:
■
15-inch CRT with a 13.7-inch (34.7 cm) diagonal viewable
image size
■
Easy-to-access front panel controls
■
Universal Serial Bus (USB) pass-through connectors for use
with USB peripherals (mouse, etc.)
English
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:36 PM
Pages: 14 Words: 2440 Template: c:\msoffice\templates\working\comm.dot
File Name BCH1_EN.doc Part Number 308012-001
1-1
■
Plug and play capability if supported by your system
■
Tilt control (image rotation) functionality
■
Automatically scans all horizontal frequencies from 30 to
60 kHz and vertical frequencies from 47.5 to 125 Hz
■
Supports VGA, Super VGA, and 1024 × 768 resolutions
■
Energy Saver feature, when activated, results in a power
savings of greater than 90 percent
■
Macintosh-compatible timing with optional connector
■
Compliant with the following regulated specifications:
❏
Swedish MPR II 1990
❏
EPA Energy Star
❏
European Union CE Directives
❏
Swedish TCO 1995 on select models
Graphics Driver
Compaq has created a Universal Driver Manager (UDM)
release that supports all Compaq QVision graphics controllers
and most graphics controllers found on Compaq Deskpro
products. The UDM eases graphics driver deployment across all
Compaq Deskpro platforms ensuring cross-compatibility and
backward-compatibility. The resulting solution enables
customers to manage and control ongoing software maintenance
costs. The UDM is available on the Support Software CD for
Compaq Desktop, Portable, and Workstation Products and the
Compaq World Wide Web site (www.compaq.com).
✎ If the updated Universal Driver Manager that supports the
Compaq monitor is not available on the Web site, contact your
authorized Compaq dealer or reseller.
1-2
■
You can order the Support Software CD for Compaq
Desktop, Portable, and Workstation Products. This compact
disc contains the latest device drivers, utilities, and
flashable ROM images needed to run MS-DOS, Microsoft
Windows 3.1, Windows 95, Windows NT Workstation, and
IBM OS/2 on your Compaq commercial Desktop, Portable,
or Workstation product.
■
You can download the Support software from the Compaq
World Wide Web site (www.compaq.com).
English
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:36 PM
Pages: 14 Words: 2440 Template: c:\msoffice\templates\working\comm.dot
File Name BCH1_EN.doc Part Number 308012-001
■
You can purchase backup diskettes from your Compaq
authorized reseller, dealer or service provider.
If you choose to purchase the Support Software CD, you have
two options:
■
You can purchase a single CD-ROM that gives you onetime access to the latest support software (North America
only, Compaq part number 272505-001).
■
You can purchase a yearly subscription that delivers up to
12 monthly CD-ROMs (Compaq part number 183426-xxx).
The annual subscription ensures your continuous access to the
latest developments.
For help and service outside of the U.S. and Canada or to order
the CD or backup diskettes, contact your Compaq authorized
reseller, dealer, or service provider. For a list of Compaq
Customer Support worldwide telephone numbers, refer to
book 8, Contacting Compaq Customer Support.
✎ If you call Compaq to place an order, be sure to have the serial
number of your monitor available. The serial number is
located on the front base of your monitor. This number is
necessary for all purchases.
English
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:36 PM
Pages: 14 Words: 2440 Template: c:\msoffice\templates\working\comm.dot
File Name BCH1_EN.doc Part Number 308012-001
1-3
Setting Up the
Monitor
To set up the monitor, ensure that the power is turned off to the
monitor, computer system, and other attached devices, then
follow these steps:
1. Place the monitor in a convenient, well-ventilated location
near your computer.
2. Connect the monitor signal cable 1 to the 15-pin connector
on the rear panel of the computer and tighten the screws.
sure the signal cable aligns with the 15-pin connector. Do not
✎ Be
force the cable onto the connector or you may damage the signal
cable.
Connect the monitor power cord 2 to the rear panel of the
monitor, then plug the other end into an electrical outlet
that is easily accessible and close to the monitor.
3.
!
WARNING: To reduce the risk of electric shock or damage to your
equipment, do not disable the power cord grounding feature. This
equipment is designed to be connected to a grounded (earthed)
power outlet that is easily accessible to the operator. The grounding
plug is an important safety feature.
CAUTION: Be sure that the power outlet you plug your power cord
into is easily accessible and located as close to the monitor as
possible. When you need to disconnect power to the equipment, be
sure to unplug the power cord from the power outlet.
1-4
English
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:36 PM
Pages: 14 Words: 2440 Template: c:\msoffice\templates\working\comm.dot
File Name BCH1_EN.doc Part Number 308012-001
USB Connectors
The base of the monitor has two Universal Serial Bus (USB)
connectors. Use connector ❶ to connect the USB signal cable
to the computer. Use connector ❷ to connect USB compatible
plug and play devices such as a keyboard, mouse, or joystick if
supported by your computer. This feature provides USB passthrough and does not support USB host requirements.
CAUTION: This USB connector is not designed for use with high
speed USB devices such as a video camera, scanner, etc. Compaq
recommends connecting high speed devices directly to the computer.
✎ These USB connectors operate as a pass-through system. Your
computer must have a USB host controller installed for any
USB-connected devices to operate.
CAUTION: To prevent deterioration of signal transfer or malfunction of
USB devices, USB cables should not exceed the combined length of 9.75
feet (3.0 meters).This length includes both the USB signal cable and the
USB peripheral cable.
English
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:36 PM
Pages: 14 Words: 2440 Template: c:\msoffice\templates\working\comm.dot
File Name BCH1_EN.doc Part Number 308012-001
1-5
Operating the Monitor
Front Panel Controls
No./Icon Control
Function
1
Horizontal Position Moves screen left or right.
2
Vertical Position
Moves screen up or down.
3
Horizontal Size
Adjusts the horizontal screen width.
4
Vertical Size
Adjusts the vertical screen height.
5
Minus
Controls degree of adjustment to functions.
6
Plus
Controls degree of adjustment to functions.
7
Pincushion
Straightens vertical lines if the picture has
pincushion or barrel distortion.
8
Trapezoid
Corrects trapezoid distortion. Adjusts the width of
the upper side of the image to equal the lower side.
9
Brightness
Adjusts screen brightness.
Continued
1-6
English
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:36 PM
Pages: 14 Words: 2440 Template: c:\msoffice\templates\working\comm.dot
File Name BCH1_EN.doc Part Number 308012-001
Front Panel Controls Continued
No./Icon
Control
Function
:
Contrast
Adjusts screen contrast.
;
Power LED
1. Green indicates monitor is turned on.
2. Amber indicates energy saver levels.
<
Power switch
Turns the monitor on and off.
Contrast and Brightness controls to their maximum
✎ Setting
settings may cause the screen to appear out of focus. To
correct this appearance, decrease the Brightness setting.
To adjust screen controls, complete the following procedures:
1. Press the desired control function button once.
Example: if you want to make adjustments to the
horizontal position (centering), press the Horizontal
Position icon once.
2. Press the Minus and Plus buttons to change the horizontal
position of the screen display.
After a period of two seconds, the adjustments are automatically
saved.
English
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:36 PM
Pages: 14 Words: 2440 Template: c:\msoffice\templates\working\comm.dot
File Name BCH1_EN.doc Part Number 308012-001
1-7
Dual Function Controls
Some controls have dual functions and, when pressed in pairs, will
adjust alternate screen functions. The following table identifies
which controls to press together to adjust a particular function.
Dual Function Controls
Icon
Control
Function
Parallelogram
Corrects a display that is leaning left or right.
+
V-linearity
Corrects a compressed display look at the top
or bottom of the screen.
+
Pinbalance
Adjusts sides of the display when they are
bowed toward left or right.
Degauss
Removes color impurities caused by magnetic
fields. Do not use the degauss feature more
than once within a 30-minute period.
Reset
Resets resolution settings to original factory
settings. Hold buttons down for 5 seconds to
reset.
User-Delete
Resets all data in the user mode memory area.
Hold buttons down for 6 seconds to reset.
Tilt
Adjusts display area for left or right rotation.
Low Power
Override
Disables the power management function.
+
+
+
+
+
+
To make the adjustment:
1. Press both buttons simultaneously and hold them for 2-3
seconds, or the time indicated in the table.
2. Use the Minus or Plus buttons to adjust the settings for
Parallelogram, V-linearity, Pinbalance, and Tilt.
The Minus and Plus buttons do not adjust the following
controls: Degauss, Recall, User-Delete, and Low Power
Override. To make an adjustment using these controls,
simply depress the required pair of buttons for 2-6 seconds
and wait two seconds before making another adjustment.
After a period of two seconds, the adjustments are automatically
saved.
1-8
English
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:36 PM
Pages: 14 Words: 2440 Template: c:\msoffice\templates\working\comm.dot
File Name BCH1_EN.doc Part Number 308012-001
Adjusting the
Monitor Screen
Allow the monitor to warm up for 30 minutes before
performing the following procedures. The screen image
stabilizes after a warm-up period.
Optimizing Contrast
For best results, set your screen to a dark background (such as
the DOS prompt) before adjusting the following settings:
1.
Set the brightness and contrast controls to their lowest
settings.
2.
Increase brightness until the background portions of the
screen are visible, then slowly reduce brightness until the
background is just extinguished.
3.
Adjust contrast control to your preference.
Optimizing Focus
The default image size is preset at the factory. The Horizontal
and Vertical Size and Position controls located on the front
control panel can be used to increase the screen size beyond the
default setting. However, increasing the screen image beyond
the default settings may degrade the focus at the outer edge of
the screen.
To enhance focus, use the lowest brightness level that gives
satisfactory results in your viewing environment.
✎ Settings that maximize contrast may not offer optimum focus,
and settings that maximize focus may not offer optimum
contrast.
English
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:36 PM
Pages: 14 Words: 2440 Template: c:\msoffice\templates\working\comm.dot
File Name BCH1_EN.doc Part Number 308012-001
1-9
Display Resolutions
Default Settings
The resolution settings listed below are the most commonly
used modes and are set as factory defaults. The monitor
automatically recognizes these preset modes as they are
requested by a software program.
Display Resolutions
Preset Modes
Resolutions
1. VESA
1024 × 768 at 60.0 kHz/75 Hz
2. VESA
1024 × 768 at 48.4 kHz/60 Hz
3. VESA
800 × 600 at 53.7 kHz/85 Hz
4. VESA
800 × 600 at 46.9 kHz/75 Hz
5. VESA
800 × 600 at 37.8 kHz/60 Hz
6. VGA
720 × 400 at 31.5 kHz/70 Hz
7. VESA
640 × 480 at 43.3 kHz/85 Hz
8. VESA
640 × 480 at 37.5 kHz/75 Hz
9. VGA
640 × 480 at 31.5 kHz/60 Hz
10. Macintosh Display Mode
832 × 624 at 49.72 kHz/74.5 Hz
User Modes
The video controller signal may occasionally call for a mode
that is not preset if:
■ You are not using a compatible Compaq graphics adapter.
■ You are not using a preset mode.
If this occurs, you may need to readjust the parameters of the
monitor screen by using the controls on the front panel. The
monitor automatically stores the new setting, then automatically
recognizes the new mode just as it does a preset mode. In
addition to the 10 preset modes that can be changed and stored,
there are 4 user modes that can be entered and stored. When the
4 user mode settings are exceeded, the newest setting will
replace the setting closest to its own setting.
To revert back to the factory default settings, select Reset using
the dual control adjustments for the front panel controls, and the
factory default resolutions will replace the current operating
mode with the original or factory default display mode.
1-10
English
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:36 PM
Pages: 14 Words: 2440 Template: c:\msoffice\templates\working\comm.dot
File Name BCH1_EN.doc Part Number 308012-001
Energy Saver
Feature
The energy saver feature has three different modes of
operation:
■
Full power mode
■
Suspend mode
■
Sleep mode
By selecting settings in the computer's Energy Saver utility, you
determine the length of inactivity before the monitor goes into
suspend or sleep mode.
The following table describes the monitor energy saver levels
available during the different modes of operation.
Energy Saver Levels
Mode
Power Usage
Description
Full Power
Less than
75 watts
ON = Normal operation
Power LED is green.
Suspend
Less than
15 watts
Monitor screen blanks. Power LED turns
amber. Full power mode returns quickly.
Sleep
Less than
5 watts
Monitor screen blanks. Power LED turns
amber. There is a brief warm-up period
before returning to full power mode.
Refer to your computer manual for instructions on setting
energy saver features (sometimes referred to as power
management features).
✎ The energy saver features for monitors only work when
connected to computers that have energy saver features.
English
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:36 PM
Pages: 14 Words: 2440 Template: c:\msoffice\templates\working\comm.dot
File Name BCH1_EN.doc Part Number 308012-001
1-11
Care and
Maintenance
This section explains how to care for and maintain your
Compaq monitor during normal everyday use.
Protecting the Monitor
To protect your monitor from overheating and other types of
damage, follow these suggestions:
1-12
■
Use only a power source and connection appropriate for
this monitor, as indicated on the marking label/back plate.
■
If an extension cord or power strip is used, make sure that
the cord or strip is rated for the product and that the total
ampere ratings of all products plugged into the extension
cord or power strip do not exceed 80% of the extension cord
or strip ampere ratings limit.
■
Do not overload an electrical outlet, power strip, or
convenience receptacle. The overall system load must not
exceed 80% of the branch circuit rating. If power strips are
used, the load should not exceed 80% of the power strip
input rating.
■
Install the monitor near an outlet that you can easily reach.
Disconnect the product by grasping the plug firmly and
pulling it from the outlet. Never disconnect it by pulling the
cord.
■
Unplug the monitor from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners.
■
Slots and openings in the cabinet are provided for
ventilation. These openings must not be blocked or covered.
Never push objects of any kind into cabinet slots or other
openings.
■
Do not place plants on top of the monitor. Water or dirt
from the plant may fall into the vents.
■
Do not drop the monitor or place it on an unstable surface.
■
Do not allow anything to rest on the power cord. Do not
walk on the cord.
English
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:36 PM
Pages: 14 Words: 2440 Template: c:\msoffice\templates\working\comm.dot
File Name BCH1_EN.doc Part Number 308012-001
■
Keep the monitor in a well-ventilated area, away from
excessive light, heat, and moisture. Keep the monitor away
from high capacity transformers, electric motors, and other
strong magnetic fields.
■
Do not open the monitor cabinet or attempt to service this
product yourself. Adjust only those controls that are
covered
by the operating instructions. If the monitor is not operating
properly or has been dropped or damaged, contact your
Compaq authorized dealer, reseller, or service provider.
Cleaning the Monitor
To clean the monitor, follow these steps:
1.
Turn off the monitor and the computer.
2.
Dust the monitor by wiping the screen and the cabinet with
a soft, clean cloth.
If the screen requires additional cleaning, use any antistatic
CRT screen cleaner.
CAUTION: Do not use benzene, thinner, ammonia, or any volatile
substance to clean the monitor screen or cabinet. These
chemicals may damage the monitor screen and cabinet finish.
Shipping the Monitor
Keep the original packing box in a storage area. You may need
it later if you move or ship your monitor.
English
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:36 PM
Pages: 14 Words: 2440 Template: c:\msoffice\templates\working\comm.dot
File Name BCH1_EN.doc Part Number 308012-001
1-13
appendix
A GENCY R EGULATORY N OTICES
Federal
Communications
Commission Notice
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
■
Reorient or relocate the receiving antenna.
■
Increase the separation between the equipment and the
receiver.
■
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
■
Consult the dealer or an experienced radio or television
technician for help.
Modifications
The FCC requires the user to be notified that any changes or
modifications made to this device that are not expressly
approved by Compaq Computer Corporation may void the
user's authority to operate the equipment.
Cables
Connections to this device must be made with shielded cables
with metallic RFI/EMI connector hoods to maintain compliance
with FCC Rules and Regulations.
Specifications
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:38 PM
Pages: 7 Words: 1193 Template: j:\template\commercl\commapp.dot
File Name CApp_en.doc Part Number 308012-001
1-15
Declaration of Conformity for Products
Marked with FCC Logo, United States Only
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
For questions regarding this declaration, contact:
Compaq Computer Corporation
P.O. Box 692000, Mail Stop 510101
Houston, Texas 77269-2000
Or call: (281) 514-3333
To identify this product, refer to the Series/model number found
on the product.
Canadian Notice
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Avis Canadien
Cet appareil numérique de la classe B respecte toutes les
exigences du Règlement sur le matériel brouilleur du Canada.
German Ergonomics Notice
Compaq Computers, when tested with the Compaq 612 Series
monitors, were evaluated and found compliant to the
requirements of ZH 1/618 (German Safety Regulations for
Display Work Places in the Office Sector) in the Text Mode
(720 × 400) using MS-DOS Version 3.31 (or higher) and
BASICA as published by Compaq Computer Corporation.
EPA Energy Star Compliance
Monitors that are marked with the Energy Star Logo meet the
requirements of the EPA Energy Star program. As an Energy
Star Partner, Compaq Computer Corporation has determined
that this product meets the Energy Star guidelines for energy
efficiency. Specific details on using the Energy Saving features
can be found in the energy saver or power management section
of the computer manual.
1-16
Specifications
Writer: Marianne Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:38 PM
Pages: 7 Words: 1193 Template: j:\template\commercl\commapp.dot
File Name CApp_en.doc Part Number 308012-001
European Notice
Products with the CE Marking comply with both the EMC
Directive (89/336/EEC) and the Low Voltage Directive
(73/23/EEC) issued by the Commission of the European
Community.
Compliance with these directives implies conformity to the
following European norms:
■
EN55022 (CISPR 22) - Radio Frequency Interference
■
EN50082-1 (IEC801-2, IEC801-3, IEC801-4) Electromagnetic Immunity
■
EN60950 (IEC950) - Product Safety
Japanese Notice
Specifications
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:38 PM
Pages: 7 Words: 1193 Template: j:\template\commercl\commapp.dot
File Name CApp_en.doc Part Number 308012-001
1-17
S PECIFICATIONS
Compaq V55 Color Monitor
Display
Viewable Image Size
(diagonal)
Screen Treatment
Approximate Weight
(Unpacked)
15-in FS CRT
38.1 cm
13.7-in
34.7 cm
Silica antiglare/antistatic coating
27.9 lb
12.7 kg
14.6-in
15.6-in
17.1-in
36.9 cm
39.3 cm
43.3 cm
Maximum Dimensions
Width
Depth
Height
Maximum Graphics
Resolution
Text Mode
Phosphor/Dot Pitch
Horizontal Frequency
Vertical Frequency
Environmental
Requirements Temperature
Operating Temp <7,000 ft
Operating Temp >7,000 ft
Storage Temperature
Humidity (Non-Condensing)
Operating
Non-Operating
Power Source
Power Consumption
Input Terminal
1-18
1024 × 768 at 75 Hz Refresh Rate
VGA or higher
P22, 0.28 mm
30 to 60 kHz
47.5 to 125 Hz
50°F to 104°F
50°F to 86°F
-22°F to 140°F
10°C to 40°C
10°C to 30°C
-30°C to 60°C
20 to 80%
5 to 95%
100 - 240 VAC, 50 - 60 Hz
< 75 watts
15-pin D-type connector with cable
Specifications
Writer: Marianne Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:38 PM
Pages: 7 Words: 1193 Template: j:\template\commercl\commapp.dot
File Name CApp_en.doc Part Number 308012-001
Connector Pin Assignments
Signal Cable
Connector
5
4
10
15
3
KEY
14
2
8
13
1
7
12
6
11
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12*
13
14
15*
Red Video
Green Video/Sync on Green
Blue Video
Ground
Return
Red Gnd
Green Gnd
Blue Gnd
Reserved (No Pin)
Sync Gnd
Ground
Bidirectional Data (SDA)
H-Sync
V-Sync24
Data Clock (SCL)
* DDC Signals
Color Display Values
CIE* Chromaticity Coordinates
X
Y
Red
0.620
0.350
Green
0.305
0.600
Blue
0.155
0.065
White Point (9300 K)
0.281 (+/- .015)
0.311 (+/- .015)
Gamma: 2.5
*Commission International d’Eclairage, 1931 Standard.
Specifications
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:38 PM
Pages: 7 Words: 1193 Template: j:\template\commercl\commapp.dot
File Name CApp_en.doc Part Number 308012-001
1-19
Power Cord Set
Requirements
The monitor power supply is provided with Automatic Line
Switching (ALS). This feature allows the monitor to operate on
input voltages between 100-240 VAC.
The power cord set (flexible cord or wall plug) received with
the monitor meets the requirements for use in the country where
you purchased the equipment.
Power cord sets must meet the requirements of the country
where you use the monitor. For more information on power
cord set requirements, contact your Compaq authorized dealer,
reseller or service provider.
General Requirements
The requirements listed below are applicable to all countries:
1. The length of the power cord set must be at least 5.00 feet
(1.5 m) and a maximum of 9.75 feet (3.0 m).
2. All power cord sets must be approved by an acceptable
accredited agency responsible for evaluation in the country
where the power cord set will be used.
3. The power cord set must have a minimum current capacity
of 10A and a nominal voltage rating of 125 VAC or 5 amps
at 250 volts AC, as required by each country’s power
system.
4. The appliance coupler must meet the mechanical
configuration of an EN 60 320/IEC 320 Standard Sheet C13
connector, for mating with appliance inlet on the rear of the
unit.
1-20
Specifications
Writer: Marianne Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:38 PM
Pages: 7 Words: 1193 Template: j:\template\commercl\commapp.dot
File Name CApp_en.doc Part Number 308012-001
Country-Specific Requirements
Power Cord Set Requirements: By Country
Country
Accredited
Agency
Applicable Note
Numbers
Australia
EANSW
1
Austria
OVE
1
Belgium
CEBC
1
Canada
CSA
2
Denmark
DEMKO
1
Finland
FIMKO
1
France
UTE
1
Germany
VDE
1
Italy
IMQ
1
Japan
MITI
3
The Netherlands
KEMA
1
Norway
NEMKO
1
Sweden
SEMKO
1
Switzerland
SEV
1
United Kingdom
BSI
1
United States
UL
2
Notes:
1. The flexible cord must be <HAR> Type HO5VV-F, 3conductor, 0.75 mm2 conductor size. Power cord set fittings
(appliance coupler and wall plug) must bear the certification
mark of the agency responsible for evaluation in the country
where it will be used.
2. The flexible cord must be Type SVT or equivalent, No. 18
AWG, 3-conductor. The wall plug must be a two-pole
grounding type with a NEMA 5-15P (15A, 125V) or NEMA
6-15P (15A 250V) configuration.
3. The appliance coupler, flexible cord, and wall plug must bear a
"T" mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or
VCTF, 3-conductor, 0.75mm2 conductor size. The wall plug
must be a two-pole grounding type with a Japanese Industrial
Standard C8303 (15A, 125V) configuration.
Specifications
Writer: M. Silvetti Saved by: Marianne Silvetti Saved date: 06/24/98 4:38 PM
Pages: 7 Words: 1193 Template: j:\template\commercl\commapp.dot
File Name CApp_en.doc Part Number 308012-001
1-21