Specifications | Compaq ML350 Server User Manual

Compaq ProLiant ML350 Generation 3 Server
Maintenance and Service Guide
Part Number 278704-002
January 2003 (Second Edition)
This document provides detailed instructions for maintenance and
service personnel. It includes removal and replacement procedures, spare
parts information, and an overview of diagnostic tools for the Compaq
ProLiant ML350 Generation 3 server.
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/19/02 8:52 AM
© 2002, 2003 Compaq Information Technologies Group, L.P.
Microsoft, Windows, and Windows NT are U.S. registered trademarks of Microsoft Corporation.
Intel is a U.S. registered trademark of Intel Corporation.
Netscape Navigator is a U.S. trademark of Netscape Communications Corporation.
Java™ is a U.S. trademark of Sun Microsystems, Inc.
Compaq shall not be liable for technical or editorial errors or omissions contained herein. The information in this
document is provided “as is” without warranty of any kind and is subject to change without notice. The warranties
for Compaq products are set forth in the express limited warranty statements accompanying such products.
Nothing herein should be construed as constituting an additional warranty.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
January 2003 (Second Edition)
Part Number 278704-002
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/19/02 8:52 AM
Contents
About This Guide
Symbols in Text............................................................................................................................................ v
Important Safety Information ....................................................................................................................... v
Compaq Technician Notes........................................................................................................................... vi
Where to Go for Additional Help ............................................................................................................... vii
Integrated Management Log ................................................................................................................ vii
Telephone Numbers ............................................................................................................................. vii
Text Conventions....................................................................................................................................... viii
Chapter 1
Illustrated Parts Catalog
Mechanical Parts Exploded View.............................................................................................................. 1-2
Mechanical Spare Parts List ...................................................................................................................... 1-3
System Components Exploded View ........................................................................................................ 1-4
System Components Spare Parts List ........................................................................................................ 1-5
Chapter 2
Removal and Replacement Procedures
Electrostatic Discharge Information .......................................................................................................... 2-2
Symbols on Equipment.............................................................................................................................. 2-3
Preparation Procedures .............................................................................................................................. 2-4
Non-Hot-Pluggable Device ................................................................................................................. 2-4
Powering Down the Server ................................................................................................................. 2-4
Rack Stability Warning.............................................................................................................................. 2-5
Bezel Door (Tower Model Only)............................................................................................................... 2-6
Access Panel .............................................................................................................................................. 2-7
Bezel (Rack Model Only) .......................................................................................................................... 2-8
Removable Media Device Blank ............................................................................................................. 2-11
Cable Routing Diagrams.......................................................................................................................... 2-12
Diskette Drive Signal Cable.............................................................................................................. 2-12
IDE CD-ROM Drive Signal Cable.................................................................................................... 2-13
Removable Media Device Cable....................................................................................................... 2-13
SCSI Point-to-Point Cable ................................................................................................................ 2-14
Air Baffle ................................................................................................................................................. 2-15
System Fan Modules................................................................................................................................ 2-16
Drive Bay Configuration ......................................................................................................................... 2-19
Hot-Plug Hard Drive Blank ..................................................................................................................... 2-20
Hot-Plug Hard Drive................................................................................................................................ 2-21
Hot-Plug Hard Drive Cage ...................................................................................................................... 2-22
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/19/02 8:52 AM
iii
Contents
Removable Media Device ....................................................................................................................... 2-24
Expansion Slots ....................................................................................................................................... 2-26
Expansion Board ..................................................................................................................................... 2-27
Memory Module Guidelines ................................................................................................................... 2-29
Memory Modules .................................................................................................................................... 2-30
Processors and Processor Power Modules .............................................................................................. 2-31
Processor........................................................................................................................................... 2-32
Processor Power Module .................................................................................................................. 2-35
System Board .......................................................................................................................................... 2-36
System Battery ........................................................................................................................................ 2-37
System Board Battery ....................................................................................................................... 2-37
Power Supply .......................................................................................................................................... 2-39
Power Supply Backplane Board.............................................................................................................. 2-40
Feet (Tower Model Only) ....................................................................................................................... 2-41
Chapter 3
Diagnostic Tools
Diagnostic Tools Utility Overview ........................................................................................................... 3-1
For More Information................................................................................................................................ 3-4
Chapter 4
Connectors, Switches, and LEDs
Connectors and Components..................................................................................................................... 4-2
Rear Panel Components...................................................................................................................... 4-2
System Board Components................................................................................................................. 4-3
Switches .................................................................................................................................................... 4-4
System Configuration Switch Settings ............................................................................................... 4-4
Resetting System Configuration Settings ........................................................................................... 4-6
LEDs ......................................................................................................................................................... 4-7
Power Button, System Status LEDs, and Unit Identification Button ................................................. 4-8
System Board LEDs ................................................................................................................................ 4-11
Hot-Plug Hard Drive LEDs .............................................................................................................. 4-13
Network Interface Controller LEDs ................................................................................................. 4-16
Chapter 5
Physical and Operating Specifications
System Unit ............................................................................................................................................... 5-2
Rack Server System Unit .......................................................................................................................... 5-3
Memory ..................................................................................................................................................... 5-4
1.44-MB Diskette Drive............................................................................................................................ 5-4
IDE CD-ROM Drive ................................................................................................................................. 5-5
Wide Ultra3 SCSI Hot-Plug Hard Drives ................................................................................................. 5-6
Integrated Compaq NC7760 Gigabit Server Auto-switching NIC............................................................ 5-6
Integrated Dual Channel Wide Ultra3 SCSI Adapter................................................................................ 5-7
Remote Insight Lights-Out Edition II Option Board................................................................................. 5-8
Index
iv
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/19/02 8:52 AM
About This Guide
This maintenance and service guide can be used for reference when servicing
Compaq ProLiant ML350 Generation 3 servers.
WARNING: To reduce the risk of personal injury from electric shock and hazardous
energy levels, only authorized service technicians should attempt to repair this
equipment. Improper repairs can create conditions that are hazardous.
Symbols in Text
These symbols may be found in the text of this guide. They have the following meanings.
WARNING: Text set off in this manner indicates that failure to follow directions in the
warning could result in bodily harm or loss of life.
CAUTION: Text set off in this manner indicates that failure to follow directions could result in
damage to equipment or loss of information.
IMPORTANT: Text set off in this manner presents clarifying information or specific instructions.
NOTE: Text set off in this manner presents commentary, sidelights, or interesting points of information.
Important Safety Information
Before installing this product, read the Important Safety Information document provided.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/19/02 8:52 AM
v
About This Guide
Compaq Technician Notes
WARNING: Only authorized technicians trained by Compaq should attempt to repair
this equipment. All troubleshooting and repair procedures are detailed to allow only
subassembly/module-level repair. Because of the complexity of the individual boards
and subassemblies, no one should attempt to make repairs at the component level or
to make modifications to any printed wiring board. Improper repairs can create a safety
hazard.
WARNING: To reduce the risk of personal injury from electric shock and hazardous
energy levels, do not exceed the level of repairs specified in these procedures.
Because of the complexity of the individual boards and subassemblies, do not attempt
to make repairs at the component level or to make modifications to any printed wiring
board. Improper repairs can create conditions that are hazardous.
WARNING: To reduce the risk of electric shock or damage to the equipment:
•
Disconnect power from the system by unplugging all power cords from the power
supplies.
•
Do not disable the power cord grounding plug. The grounding plug is an important
safety feature.
•
Plug the power cord into a grounded (earthed) electrical outlet that is easily
accessible at all times.
CAUTION: To properly ventilate the system, you must provide at least 7.6 cm (3.0 in.) of
clearance at the front and back of the server.
CAUTION: The computer is designed to be electrically grounded (earthed). To ensure proper
operation, plug the AC power cord into a properly grounded AC outlet only.
NOTE: Any indications of component replacement or printed wiring board modifications may void any
warranty.
vi
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/19/02 8:52 AM
About This Guide
Where to Go for Additional Help
In addition to this guide, the following information sources are available:
•
User documentation
•
Compaq Service Quick Reference Guide
•
Service training guides
•
Compaq service advisories and bulletins
•
Compaq QuickFind™ information services
•
Compaq Insight Manager software
For additional copies, go to www.compaq.com.
Integrated Management Log
The server includes an integrated, nonvolatile management log that contains fault and
management information. The contents of the Integrated Management Log (IML) can be
viewed with the Compaq Insight Manager.
Telephone Numbers
For the name of your nearest Compaq authorized reseller:
•
In the United States, call 1-800-345-1518.
•
In Canada, call 1-800-263-5868.
For Compaq technical support:
•
In the United States and Canada, call 1-800-652-6672.
•
Outside the United States and Canada, refer to www.compaq.com.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/19/02 8:52 AM
vii
About This Guide
Text Conventions
This document uses the following conventions:
•
Italic type is used for complete titles of published guides or variables. Variables include
information that varies in system output, in command lines, and in command parameters
in text.
•
Bold type is used for emphasis, for onscreen interface components (window titles, menu
names and selections, button and icon names, and so on), and for keyboard keys.
•
Monospace typeface is used for command lines, code examples, screen displays,
error messages, and user input.
•
viii
Sans serif typeface is used for uniform resource locators (URLs).
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/19/02 8:52 AM
1
Illustrated Parts Catalog
This chapter provides the illustrated parts breakdown and spare parts lists for the
Compaq ProLiant™ ML350 Generation 3 server. Refer to Table 1-1, and Table 1-2 for the
names of referenced spare parts.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/31/02 9:35 AM
1-1
Illustrated Parts Catalog
Mechanical Parts Exploded View
2c
1
2a
2b
6
10
7
5a
5b
5b
9
4
3
8
Figure 1-1: Mechanical parts exploded view
1-2
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/31/02 9:35 AM
Illustrated Parts Catalog
Mechanical Spare Parts List
Table 1-1: Mechanical Spare Parts List
Item
Description
Spare Part Number
Chassis
1
Bezel door (tower model only)
249927-001
2
Cover kit
216104-001
a) Hood panel (tower model only)
b) Access panel
c) Top panel
3
Hot-plug hard drive cage
262171-001
4
Hot-plug hard drive blank
122759-001
5
Miscellaneous plastics kit
250843-001
a) Expansion board retainer
b) Feet (4) (tower model only)
c) Expansion board guide*
d) Retainer clips*
6
Power supply blank
249923-001
7
Air baffle
289549-001
8
Front faceplate and bezel (rack model only)
249928-001
9
Rack-mounting hardware kit with rails and cable management arm
292230-001
10
Removable media device blank
231212-001
*Not shown
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/31/02 9:35 AM
1-3
Illustrated Parts Catalog
System Components Exploded View
19
15
11
16
14
13
20
18
22
17
21
23
12
Figure 1-2: System components exploded view
1-4
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/31/02 9:35 AM
Illustrated Parts Catalog
System Components Spare Parts List
Table 1-2: System Components Spare Parts List
Item
Description
Spare Part Number
11
CPU fan module, 120 mm
301017-001
12
I/O fan module, 92 mm
289562-001
Boards
13
System board
292234-001
14
Power supply backplane board with cover
292235-001
Mass storage devices
15
IDE CD-ROM drive (48X)
288894-001
16
Diskette drive
233409-001
17
Hot-plug hard drive cage
262171-001
Power
18
Power switch assembly
292236-001
19
500-W power supply with power factor correction
292237-001
20
Processor Power Module (PPM)
289564-001
Options
21
Processor with Heatsink
a) Intel Xeon 2.0-GHz/400-MHz
301018-001
b) Intel Xeon 2.2-GHz/400-MHz*
301019-001
c) Intel Xeon 2.4-GHz/400-MHz*
290558-001
22
CR2032 lithium battery for system board
234556-001
23
Memory
b) 256-MB PC2100 DDR ECC Registered DIMM
300699-001
c) 512-MB PC2100 DDR ECC Registered DIMM*
300700-001
d) 1-GB PC2100 DDR ECC Registered DIMM*
300701-001
e) 2-GB PC2100 DDR ECC Registered DIMM*
300702-001
*Not shown
continued
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/31/02 9:35 AM
1-5
Illustrated Parts Catalog
Table 1-2: System Components Spare Parts List continued
Item
Description
Spare Part Number
Miscellaneous
24
Enhanced keyboard (carbon)*
244000-001
25
Signal cable kit*
163353-001
a) IDE ribbon cable assembly
b) Diskette drive cable assembly
c) Removable media device SCSI cable
26
SCSI Point-to-Point cable*
292232-001
27
Return kit (tower model only)*
249929-001
28
Return kit (rack model only)*
250189-001
29
Country kit*
303713-001
30
Tower-to-rack conversion kit*
292231-001
*Not shown
1-6
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/31/02 9:35 AM
2
Removal and Replacement Procedures
This chapter provides subassembly/module-level removal and replacement procedures for the
Compaq ProLiant ML350 Generation 3 server. After completing any removal or replacement
procedure, run the diagnostics program to verify that all components operate properly.
To service the server, a Torx T-15 screwdriver may be needed.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-1
Removal and Replacement Procedures
Electrostatic Discharge Information
An electrostatic discharge (ESD) can damage static-sensitive devices or microcircuitry.
Proper packaging and grounding techniques are necessary precautions to prevent damage. To
prevent electrostatic damage, observe the following precautions:
2-2
•
Transport products in static-safe containers such as conductive tubes, bags, or boxes.
•
Keep electrostatic-sensitive parts in their containers until they arrive at static-free
stations.
•
Cover workstations with approved static-dissipating material. Use a wrist strap connected
to the work surface, and properly grounded (earthed) tools and equipment.
•
Keep work area free of nonconductive materials, such as ordinary plastic assembly aids
and foam packing.
•
Make sure that you are always properly grounded (earthed) when touching a
static-sensitive component or assembly.
•
Avoid touching pins, leads, or circuitry.
•
Always place drives with the Printed Circuit Board (PCB) assembly-side down.
•
Use conductive field service tools.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
Symbols on Equipment
These symbols may be located on equipment in areas where hazardous conditions may exist.
WARNING: This symbol, in conjunction with any of the following symbols,
indicates the presence of a potential hazard. The potential for injury exists if
warnings are not observed. Consult your documentation for specific details.
This symbol indicates the presence of hazardous energy circuits or electric
shock hazards. Refer all servicing to qualified personnel.
WARNING: To reduce the risk of injury from electric shock hazards, do not
open this enclosure. Refer all maintenance, upgrades, and servicing to
qualified personnel.
This symbol indicates the presence of electric shock hazards. The area
contains no user or field serviceable parts. Do not open for any reason.
WARNING: To reduce the risk of injury from electric shock hazards, do not
open this enclosure
This symbol on an RJ-45 receptacle indicates a network interface connection.
WARNING: To reduce the risk of electric shock, fire, or damage to the
equipment, do not plug telephone or telecommunications connectors into this
receptacle.
This symbol indicates the presence of a hot surface or hot component. If this
surface is contacted, the potential for injury exists.
WARNING: To reduce the risk of injury from a hot component, allow the
surface to cool before touching.
These symbols, on power supplies or systems, indicate that the
equipment is supplied by multiple sources of power.
WARNING: To reduce the risk of injury from electric shock,
remove all power cords to completely disconnect power from the
system.
This symbol indicates that the component exceeds the recommended
weight for one individual to handle safely.
Weight in kg
Weight in lb
WARNING: To reduce the risk of personal injury or damage to the
equipment, observe local occupational health and safety requirements
and guidelines for manual material handling.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-3
Removal and Replacement Procedures
Preparation Procedures
WARNING: Only authorized technicians trained by Compaq should attempt to repair
this equipment. Because of the complexity of the individual boards and subassemblies,
no one should attempt to make repairs at the component level or to make modifications
to any printed wiring board. Improper repairs can create a safety hazard.
CAUTION: Electrostatic discharge (ESD) can damage electronic components. Be sure that
you are properly grounded (earthed) before beginning any installation procedure. Refer to
“Electrostatic Discharge Information” earlier in this chapter for more information.
Before removing any serviceable parts, determine whether the part is hot-pluggable or
non-hot-pluggable.
Non-Hot-Pluggable Device
If the device is non-hot-pluggable, the server must be powered down. Non-hot-pluggable
devices in the server include the processor, all boards, memory modules, fans, PCI option
cards, and drive cages.
Powering Down the Server
The server does not completely power down when the front panel power button is pressed.
The button toggles between On and Standby. The standby position removes power from most
electronics and the drives, but some internal circuitry remains active. To completely remove
all power from the system, disconnect all power cords from the server.
WARNING: To reduce the risk of injury from electric shock, disconnect all power cords
to completely remove power from the system.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal
system components to cool before touching them.
CAUTION: Protect the server from power fluctuations and temporary interruptions with a
regulating uninterruptible power supply (UPS). This device protects the hardware from
damage caused by power surges and voltage spikes, and keeps the system in operation
during a power failure.
CAUTION: The server must always be operated with system unit covers on. Proper cooling is
not achieved when the system unit covers are removed.
2-4
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
To power down the server:
1. Press the power button to toggle to Standby. This places the server in standby mode,
disabling the main power supply output and providing auxiliary power to the server.
Standby does not completely disable or remove power from the system.
2. Be sure that the system LED closest to the right on the front panel is amber and that the
fan noise has stopped.
3. Disconnect the AC power cord from the AC outlet, and then from the server.
4. Disconnect all external peripheral devices from the server.
Rack Stability Warning
For stability and safety, properly positioning the server is critical.
WARNING: To reduce the risk of personal injury or damage to the equipment, be sure
that:
•
The leveling jacks are extended to the floor.
•
The full weight of the rack rests on the leveling jacks.
•
The stabilizing feet are connected to the rack if it is a single-rack installation.
•
The racks are coupled together in multiple-rack installations.
•
Only one component is extended at a time. A rack may become unstable if more
than one component is extended for any reason.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-5
Removal and Replacement Procedures
Bezel Door (Tower Model Only)
To remove the bezel door:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. If the keylock is locked, unlock the bezel door using the included key (1).
3. Open the bezel door fully to the right (2).
4. Lift the bezel door and then pull it away from the chassis (3).
3
2
1
Figure 2-1: Removing the bezel door (tower model only)
To replace the bezel door, reverse steps 3 and 4.
2-6
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
Access Panel
To remove the access panel:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Open the bezel door fully to the right. Refer to “Bezel Door” earlier in this chapter.
3. Loosen the two thumbscrews located on the left of the front chassis (1).
4. Slide the access panel back about 1.5 cm (0.5 inch), then lift and remove the panel (2).
2
1
Figure 2-2: Removing the access panel
To replace the access panel, reverse steps 2 through 4.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-7
Removal and Replacement Procedures
Bezel (Rack Model Only)
To remove the bezel:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Loosen the thumbscrews holding the chassis in the rack (1).
3. Fully extend the chassis from the rack.
1
Figure 2-3: Loosen the thumbscrews holding the
chassis and fully extend the chassis from the rack
2-8
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
4. Loosen the access panel thumbscrews (1).
5. Slide the access panel back about 1.5 cm (0.5 inch), then lift and remove the panel (2).
2
1
Figure 2-4: Loosening the access panel thumbscrews
6. Loosen the two thumbscrews securing the rack bezel to the chassis.
Figure 2-5: Loosening the thumbscrews securing the
rack bezel to the chassis
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-9
Removal and Replacement Procedures
7. Pull the bezel up and away from the chassis.
Figure 2-6: Removing the bezel (rack model only)
To replace the bezel, reverse steps 2 through 7.
2-10
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
Removable Media Device Blank
IMPORTANT: To install a removable media device or a hard drive for the first time, the removable
media device blank must be removed from an available removable media bay.
To remove a removable media device blank from the front chassis:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Open the bezel door. Refer to “Bezel Door” earlier in this chapter.
3. Remove the access panel. Refer to “Access Panel” earlier in this chapter.
4. Push up on the drivelock to release the device blanks (1).
5. Gently pull the appropriate blank completely out from the front of the chassis (2).
2
1
Figure 2-7: Removing the media device blank
To replace the media device blank, reverse steps 2 through 5.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-11
Removal and Replacement Procedures
Cable Routing Diagrams
Figure 2-8 through Figure 2-11 show the cable routing for the server.
CAUTION: When routing cables, be sure that the cables are not in a position where they can
be pinched or crimped.
Diskette Drive Signal Cable
Figure 2-8: Diskette drive signal cable routing
2-12
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
IDE CD-ROM Drive Signal Cable
Figure 2-9: IDE CD-ROM drive signal cable routing
Removable Media Device Cable
2
1
Figure 2-10: Removable media device cable routing
Table 2-1: Removable Media Device Cable Routing
Item
Description
1
Signal cable
2
Power cable
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-13
Removal and Replacement Procedures
SCSI Point-to-Point Cable
Figure 2-11: SCSI LVD Point-to-Point cable routing
2-14
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
Air Baffle
To remove the air baffle:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Open the bezel door. Refer to “Bezel Door” earlier in this chapter.
3. Remove the access panel. Refer to “Access Panel” earlier in this chapter.
4. Loosen the thumbscrew (1) and remove the PCI card retainer.
5. Loosen the thumbscrew that secures the air baffle to the server chassis (2).
6. Lift the air baffle out of the server (3).
2
3
1
Figure 2-12: Removing the air baffle
To replace the air baffle, reverse steps 2 through 6.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-15
Removal and Replacement Procedures
System Fan Modules
To remove the system CPU fan module:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Open the bezel door. Refer to “Bezel Door” earlier in this chapter.
3. Remove the access panel. Refer to “Access Panel” earlier in this chapter.
4. Remove the air baffle. Refer to “Air Baffle” earlier in this chapter.
5. Disconnect the system CPU fan cable (1) from the system board.
NOTE: I/O fan cable connection show for clarity (2).
1
2
Figure 2-13: Disconnecting the fan cables from the
system board
2-16
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
6. Loosen the thumbscrew securing the system CPU fan module to the chassis (1).
7. Carefully pull the system CPU fan module away from and out of the chassis (2).
1
2
Figure 2-14: Removing the system CPU fan module
To replace the system CPU fan module, reverse steps 2 through 7.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-17
Removal and Replacement Procedures
To remove the front I/O system fan module:
1. Disconnect the I/O fan cable from the system board (2). Refer to Figure 2-13.
2
1
Figure 2-15: Removing the system I/O fan module
2. Loosen the thumbscrew securing the I/O fan module to the chassis (1).
3. Carefully lift the I/O fan module out and away from the chassis (2).
To replace the I/O fan module, reverse steps 1 through 3.
2-18
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
Drive Bay Configuration
The server supports a maximum of ten internal drive bays (four are for removable media
devices; six are for hot-plug hard drives). The removable media device bays contain an
one-third height, 1.44-MB diskette drive; a one-half height IDE CD-ROM drive; and two
empty half-height drive bays. The empty bays may be used for a DVD-ROM drive, tape
drive, non-hot-pluggable hard drive, any SCSI device or a 2-bay SCSI drive cage, including a
DLT tape drive. A DLT tape drive or the 2-bay SCSI drive cage require both empty
half-height drive bays.
1
2
3
4
Figure 2-16: Server drive bay configuration
Table 2-2: Drive Bay Configuration
Item
Description
1
Removable media device bays
2
CD-ROM drive
3
1.44-MB diskette drive
4
Hot-plug hard drive bays
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-19
Removal and Replacement Procedures
Hot-Plug Hard Drive Blank
NOTE: The server does not need to be powered off to complete this operation.
To remove a hot-plug hard drive blank:
1. Open the bezel door. Refer to “Bezel Door” earlier in this chapter.
2. Slide the release latch to the left (1), and then pull the hot-plug drive blank out of the
drive bay (2).
1
2
Figure 2-17: Removing a hot-plug hard drive blank
To replace a hot-plug hard drive blank, reverse steps 1 and 2.
2-20
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
Hot-Plug Hard Drive
NOTE: The server does not need to be powered off to complete this operation.
To remove a hot-plug hard drive:
1. Open the bezel door. Refer to “Bezel Door” earlier in this chapter.
2. Slide the hard drive release latch (1) to open the ejector lever (2).
3. Pull the hot-plug hard drive out of the drive bay.
2
1
Figure 2-18: Removing a hot-plug hard drive
To replace a hot-plug hard drive, push the drive back into the bay and then close the ejector
lever to fully seat the drive.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-21
Removal and Replacement Procedures
Hot-Plug Hard Drive Cage
To remove a hot-plug hard drive cage:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Remove the bezel door. Refer to “Bezel Door” earlier in this chapter.
3. Remove the access panel. Refer to “Access Panel” earlier in this chapter.
4. Disconnect the power cable from the back of the hot-plug hard drive cage (1).
5. Disconnect the SCSI cable from the back of the hot-plug hard drive cage and system
board (2).
1
2
2
Figure 2-19: Disconnecting cables from the hot-plug
hard drive cage
2-22
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
6. Remove all drive blanks and hard drives. Refer to “Hot-Plug Hard Drive Blank” and
“Hot-Plug Hard Drive” earlier in this chapter.
7. Remove the four screws securing the drive cage to the chassis with a Torx T-15
screwdriver (1).
8. Pull the hot-plug hard drive cage out from the chassis (2).
1
2
1
1
Figure 2-20: Removing a hot-plug hard drive cage
To replace a hot-plug hard drive cage, reverse steps 2 through 8.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-23
Removal and Replacement Procedures
Removable Media Device
To remove a removable media device:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Open the bezel door. Refer to “Bezel Door” earlier in this chapter.
3. Remove the access panel. Refer to “Access Panel” earlier in this chapter.
4. Disconnect the cables from the back of the removable media device and the system
board.
Figure 2-21: Disconnecting the removable media device
cables
2-24
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
5. While pushing up the drivelock (1), pull the removable media device out of the bay (2).
2
1
Figure 2-22: Removing the removable media device
To replace a removable media device, insert the device into the bay until the device clicks
into place.
NOTE: It is not necessary to push up on the drivelock when installing a removable media device.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-25
Removal and Replacement Procedures
Expansion Slots
1
2
3
4
5
Figure 2-23: Expansion slot locations
Table 2-3: Expansion Slots
Item
Slot
Slot Number
1
64-bit 100-MHz PCI-X, 3.3-V, bus 2
1
2
64-bit 100-MHz PCI-X, 3.3-V, bus 2
2
3
64-bit 100-MHz PCI-X, 3.3-V, bus 5
3
4
64-bit 100-MHz PCI-X, 3.3-V, bus 5
4
5
32-bit 33-MHz PCI, 5-V
5
Note: Slots 1, 2, 3 and 4 are optimized for PCI-X 100 add-in
cards.
2-26
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
Expansion Board
To remove an expansion board:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Open the bezel door. Refer to “Bezel Door” earlier in this chapter.
3. Remove the access panel. Refer to “Access Panel” earlier in this chapter.
4. Disconnect any cables connected to the expansion board.
5. If an expansion board retainer is in place:
a. Loosen the thumbscrew of the expansion board retainer (1).
b. Lift the retainer away from and out of the chassis (2).
2
1
Figure 2-24: Removing the expansion board retainer
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-27
Removal and Replacement Procedures
6. Press on the top of the expansion slot latch (1) and open the latch toward the rear of the
chassis (2).
7. Remove the expansion board (3).
8. Close the expansion slot latch.
9. Replace the expansion board retainer if the expansion board is not immediately being
replaced.
2
1
3
Figure 2-25: Removing the expansion board
To replace an expansion board, reverse steps 2 through 9.
2-28
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
Memory Module Guidelines
CAUTION: To prevent damage to equipment or loss of information, make sure that the server
is powered down, all cables are disconnected from the back of the server, and the power cord
is disconnected from the grounded (earthed) AC outlet before removing the access panel.
CAUTION: To prevent damage to the system when handling components, refer to the
Compaq ProLiant ML350 Generation 3 Server Setup and Installation Guide.
CAUTION: When handling a memory module, be careful not to touch any of the contacts.
Doing so may damage the module.
4
3
2
1
Figure 2-26: DDR SDRAM DIMM sockets location
The following guidelines must be followed when memory modules are being added or
replaced:
•
DIMMs must be industry-standard, 128-MB, 256-MB, 512-MB, 1-GB or 2-GB,
3-cm (1.2-inch), 184-pin PC2100, DDR ECC memory DIMMs. The DDR memory
DIMMs must support CAS Latency 2, CL=2 or greater. They must also contain the
mandatory Joint Electronic Device Engineering Council (JEDEC) Serial Presence Detect
(SPD) information.
•
If two-way memory interleaving is desired, identical DIMMs must be installed in socket
pairs. DIMMs installed in Pair A (sockets 1 and 2), however do not need to be identical
to the DIMMs in pair B (sockets 3 and 4). If the two DIMMs within a pair are not
identical, the system will automatically run in non-interleaved mode.
•
DIMMs installed in the server must be registered DDR, 3.3-volts, 72-bits wide.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-29
Removal and Replacement Procedures
•
Do not mix ECC and non-ECC DIMMs. If different types of DIMMs are mixed, the
system will not properly function.
•
A DIMM will only fit one way in the socket. Be sure to match the two key slots in the
DIMM with the tabs in the DIMM socket. Push the memory module into the DIMM
socket, ensuring that it is fully inserted and properly seated.
Memory Modules
CAUTION: Electrostatic discharge (ESD) can damage electronic components. Be sure that
you are properly grounded (earthed) before beginning any installation procedure. Refer to
“Electrostatic Discharge Information” earlier in this chapter.
To remove a memory module:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Open the bezel door. Refer to “Bezel Door” earlier in this chapter.
3. Remove the access panel. Refer to “Access Panel” earlier in this chapter.
4. Press both memory module socket latches outward (1). This action releases the module
and partially lifts it out of the socket.
5. Lift out the memory module (2).
IMPORTANT: A memory module can be installed only one way. Be sure to match the key sockets on
the module with the tabs on the memory socket. Push the module down into the socket. Be sure that
the module is fully inserted and properly seated.
1
2
1
Figure 2-27: Removing a memory module
To replace a memory module, reverse steps 2 through 5.
2-30
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
Processors and Processor Power Modules
1
2
3
4
Figure 2-28: Processor and Processor Power Module
(PPM) locations
Table 2-4: Processor and Processor Power Module
(PPM) Locations
Item
Description
1
PPM socket 1 (populated)
2
Processor socket 1 (populated)
3
Processor socket 2
4
PPM socket 2
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-31
Removal and Replacement Procedures
Processor
CAUTION: Electrostatic discharge (ESD) can damage electronic components. Be sure that
you are properly grounded (earthed) before beginning any installation procedure. Refer to
“Electrostatic Discharge Information” earlier in this chapter.
To remove a processor:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Open the bezel door. Refer to “Bezel Door” earlier in this chapter.
3. Remove the access panel. Refer to “Access Panel” earlier in this chapter.
4. Remove the air baffle. Refer to “Air Baffle” earlier in this chapter.
IMPORTANT: For tower models, lay the system on the right side.
5. Locate the processor on the system board.
6. Lift up on the processor-cage retaining latch.
IMPORTANT: The lever must be perpendicular to the board or socket for the processor to unlock.
Figure 2-29: Releasing the processor-cage latch
2-32
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
7. Rotate the processor cage upward.
Figure 2-30: Rotating the processor cage
8. Rotate the processor-locking lever to release the processor.
Figure 2-31: Releasing the processor-locking lever
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-33
Removal and Replacement Procedures
9. Remove the processor/heatsink assembly from the socket.
Figure 2-32: Removing the processor/heatsink
assembly
CAUTION: Failure to fully open the processor locking lever will prevent the processor from
seating properly during installation and can potentially lead to hardware damage.
CAUTION: To prevent possible server malfunction, be sure to completely close the processor
locking lever.
To replace the processor, reverse steps 2 through 9.
2-34
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
Processor Power Module
WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal
system components to cool before touching them.
To remove a Processor Power Module (PPM):
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Open the bezel door. Refer to “Bezel Door” earlier in this chapter.
3. Remove the access panel. Refer to “Access Panel” earlier in this chapter.
4. Locate the PPM to be removed.
5. Press the latches outward to release the PPM (1).
6. Lift the PPM away from the socket (2).
1
1
2
Figure 2-33: Removing a Processor Power Module
(PPM)
To replace a PPM, reverse steps 2 through 6.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-35
Removal and Replacement Procedures
System Board
To remove the system board:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Open the bezel door. Refer to “Bezel Door” earlier in this chapter.
3. Remove the access panel. Refer to “Access Panel” earlier in this chapter.
4. Remove the air baffle. Refer to “Air Baffle” earlier in this chapter.
IMPORTANT: For tower models, lay the system on the right side.
5. Remove the CPU fan module. Refer to “System Fan Modules” earlier in this chapter.
6. Disconnect all power cables, device cables, and the power button cable from the system
board. Refer to “Cable Routing Diagrams” earlier in this chapter.
7. Remove all expansion board(s) and memory modules. Refer to “Expansion Board” and
“Memory Modules” earlier in this chapter.
8. Remove all processors and Processor Power Modules (PPMs). Refer to “Processors and
Processor Power Modules” earlier in this chapter.
9. Remove the four screws securing the system board to the chassis with a Torx T-15
screwdriver (1).
10. Push the system board toward the front of the unit until the board stops (2).
11. Holding the system board from the edges, lift up the rear of the system board, pulling up
and away from the chassis (3).
1
2
3
1
Figure 2-34: Removing the system board
To replace the system board, reverse steps 2 through 11.
2-36
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
System Battery
The server uses nonvolatile memory that requires a battery to retain system information when
power is removed. The battery is on the system board.
System Board Battery
If the server no longer automatically displays the correct date and time, the system board
battery that provides power to the real-time clock may need to be replaced. Under normal use,
battery life is 5 to 10 years.
WARNING: The system board contains a lithium battery. There is a risk of fire and
chemical burn if the battery is improperly handled. Do not disassemble, crush,
puncture, or short external contacts, dispose of in water or fire, or expose the battery
to temperatures higher than 60°°C (140°°F).
CAUTION: Static electricity can damage the electronic components of the server. Before
beginning these procedures, be sure that you are discharged of static electricity by briefly
touching a grounded (earthed) metal object. Refer to “Electrostatic Discharge Information”
earlier in this chapter.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-37
Removal and Replacement Procedures
To replace the system board battery:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Open the bezel door. Refer to “Bezel Door” earlier in this chapter.
3. Remove the access panel. Refer to “Access Panel” earlier in this chapter.
4. Locate the battery on the system board.
5. Press the battery release lever away from the battery (1).
6. Lift the battery up from that side and out of its holder (2).
IMPORTANT: The battery should be installed with the positive polarity (+ side) positioned up.
NOTE: If expansion boards are installed, you may need to remove them to gain access to the battery.
1
2
Figure 2-35: Locating and removing a system board
battery
2-38
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
Power Supply
To remove the power supply:
IMPORTANT: The power supply of the server is hot-pluggable. When removing a power supply, do not
power down the server when the redundant power supply option is used.
1. Remove the power cord from the power supply to be removed from the server.
2. Push down on the power supply release latch (1).
3. Slide the power supply out of the server (2).
1
2
Figure 2-36: Removing the power supply (shown with
optional redundant power supply)
To replace the power supply, reverse steps 1 through 3.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-39
Removal and Replacement Procedures
Power Supply Backplane Board
To remove the power supply backplane board:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Remove the access panel. Refer to “Access Panel” earlier in this chapter.
3. Remove any installed power supplies. Refer to “Power Supply” in the previous section.
4. Remove all cables from the power supply backplane board.
5. Loosen the thumbscrew securing the power supply backplane board to the server
chassis (1).
6. Slide the power supply backplane board slightly toward the open side of the chassis to
release the power supply backplane board from the mounting posts, and then lift the
board up and out of the chassis (2).
1
2
Figure 2-37: Removing the power supply backplane
board
To replace the power supply backplane board, reverse steps 2 through 6.
2-40
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
Removal and Replacement Procedures
Feet (Tower Model Only)
To remove the four feet from the chassis, one at a time:
1. Complete the preparation procedures. Refer to “Preparation Procedures” earlier in this
chapter.
2. Place the server upside down.
3. Remove the Torx T-15 screw that secures each foot to the chassis (1).
4. Lift up the other end of each foot (2) and pull it off the base of the chassis (3).
1
2
3
Figure 2-38: Removing the feet from the chassis
To replace the feet, reverse steps 2 through 4.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:43 AM
2-41
3
Diagnostic Tools
This chapter provides an overview of the software and firmware diagnostic tools available for
the Compaq ProLiant ML350 Generation 3 server.
Diagnostic Tools Utility Overview
The following utilities were developed to assist in diagnosing problems, testing the hardware,
and monitoring and managing the server hardware.
Table 3-1: Diagnostic Tools
Tool
Description
How to run it
Compaq Diagnostics
Utility
Utility to assist testing and/or verifying operation
of Compaq hardware. If problems are found,
Compaq Diagnostics isolates failures down to
the replaceable part, whenever possible.
Diagnostics and utilities must be
accessed when a system configuration
error is detected during Power-On
Self-Test (POST). For a complete list of
POST error messages, refer to the
Compaq Servers Troubleshooting
Guide.
Compaq Diagnostics software is also
available on the Compaq SmartStart™
software CD. A Diagnostics diskette
may be created from the SmartStart
software CD. Diagnostics can then be
run from the diskette.
Compaq Insight
TM
Manager application
A client/server application that remotely
manages Compaq systems in a network
environment. Reports hardware fault conditions
(both failure and prefailure) and collects data for
reporting and graphing.
For more information, refer to the
Compaq Insight Manager User Guide.
Documentation for Compaq Insight
Manager is available on the Compaq
Management CD in
CD-ROM DRIVE: \OVERVIEW.HLP
continued
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:44 AM
3-1
Diagnostic Tools
Table 3-1: Diagnostic Tools continued
Tool
Description
How to run it
Compaq Survey Utility
An online information-gathering program that
runs on servers, gathering critical hardware and
software information from various sources. A
utility for servers running
Microsoft Windows NT, Linux, or Novell
NetWare.
Compaq Survey Utility automatically
runs at startup and user-specified time
intervals. Modify the command-line
parameters to change the datagathering interval.
If a significant change occurs between datagathering intervals, previous information is
marked, and the survey text file is appended to
reflect the latest configuration and changes
since the last configuration. This utility provides
a historical record of change events for server
hardware and software.
For more information on Compaq
Survey Utility, including installation and
application procedures, refer to the
Compaq Survey Utility Online Help User
Guide accessed through:
www.hp.com/servers/proliant/manage.
Perform a search for “Survey Utility”,
then follow the appropriate link.
Compaq SmartStart
software
Located on the SmartStart CD, the SmartStart
utility is the intelligent way to set up your
Compaq server. The SmartStart CD is used to
load the system software, thereby achieving a
well-integrated server and ensuring maximum
dependability and supportability. The SmartStart
CD contains diagnostic utilities and ROMPaq
tools.
Power up from the SmartStart Software
for Servers CD.
SmartStart Diskette
Builder
Creates a diskette version of the utility from the
SmartStart CD. The support diskettes include
the following:
Use a workstation running Windows
XP, Windows 95, Windows 98,
Windows NT, or Windows 2000. You
also need several 1.44-MB diskettes.
Insert the SmartStart CD into the
workstation drive. The CD automatically
runs the Diskette Builder Utility;
however, if the server does not support
the “auto-run” feature, use Windows
Explorer to run CD-ROM DRIVE:
\DSKBLDR\DSKBLDR.EXE.
ROMPaq™ Utility
•
Array Configuration Utility (ACU)
•
Operating System support
•
Server Utilities
•
Erase Utility
Utility that upgrades the current system ROM.
Insert a ROMPaq diskette into the
diskette drive, remove power from the
server, and then power up the server
again.
continued
3-2
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:44 AM
Diagnostic Tools
Table 3-1: Diagnostic Tools continued
Tool
Description
How to run it
System Firmware
Update
Utility that enables Windows NT 4 and Windows
2000 to efficiently update system and array
controller ROMs on remote servers from a
central location.
Latest maintenance ROM executable
file can be downloaded from
www.hp.com/servers/proliant/manage
ROM-Based Setup
Utility (RBSU)
Utility used to configure some hardware
installed in or connected to the server.
Specifically, it can:
Run RBSU directly from the system
ROM by pressing the F9 key when
prompted during POST.
Automatic Server
Recovery (ASR)
•
Resolve resource conflicts in areas such as
memory, port addresses, and interrupts
(IRQs)
•
Configure PCI boards automatically
•
Manage installation of memory, processor
upgrades, and mass storage devices such
as hard drives, tape drives, and diskette
drives
•
Store configuration information in
nonvolatile memory
•
Configure the platform for an operating
system
A tool that restarts the server automatically after
a catastrophic operating system failure,
including software errors, OS lockups,
environmental abnormalities, and some
hardware errors.
A system failsafe timer, the ASR timer, is
started when the Compaq System Management
driver, also known as the health driver, is
loaded. The Compaq Insight Manager console
notifies you in the event of an ASR restart.
Disable the ASR from the Compaq Insight
Manager console.
POST
The POST is a series of diagnostic tests that
checks firmware and assemblies to ensure that
the server is properly functioning.
This tool is a function of the
hardware/software system through
RBSU. Verify that this tool is enabled
through RBSU. The systems
management drive must be loaded to
activate ASR.
POST runs automatically on Compaq
servers when the server is powered up.
continued
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:44 AM
3-3
Diagnostic Tools
Table 3-1: Diagnostic Tools continued
Tool
Description
How to run it
INSPECT
A utility that provides a report detailing system
information.
INSPECT can be run from the Compaq
Diagnostics program.
Integrated
Management Log
(IML)
A log of system events, such as system failures
or nonfatal error conditions. View events in the
IML from within:
The IML requires Compaq operating
system-dependent drivers. Refer to the
Compaq Software Support CD for
instructions on installing the appropriate
drivers.
Array Diagnostics
Utility (ADU)
•
Compaq Insight Manager
•
Compaq Survey utility
•
OS-specific IML utilities
A Windows-based tool designed to run on all
Compaq systems that support Compaq array
controllers. The main functions of ADU are to
collect all possible information about the array
controllers in the system and to generate a list
of detected problems.
Power up the SmartStart for Servers CD
or use the Diskette Builder (also located
on the CD) to create ADU bootable
diskettes.
Use the information provided in the
ADU.
For a complete list of ADU error
messages, refer to the Compaq Servers
Troubleshooting Guide.
For More Information
For detailed information about each of these diagnostic tools, refer to the Compaq Servers
Troubleshooting Guide on the documentation CD. For the most recent version of this guide,
go to
www.compaq.com/support/servers.
3-4
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:44 AM
4
Connectors, Switches, and LEDs
This chapter contains illustrations and tables identifying and describing connectors, switches,
and LED locations on the front panel, rear panel, system board and hard drives for the
Compaq ProLiant ML350 Generation 3 server.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
4-1
Connectors, Switches, and LEDs
Connectors and Components
This section contains illustrations and tables identifying connector locations and components
on the server rear panel and system board.
Rear Panel Components
Figure 4-1 and Table 4-1 show and describe the location of the components on the rear panel
of the server.
1
12
2
11
3
10
9
8
4
7
5
6
Figure 4-1: Rear panel components
Table 4-1: Rear Panel Components
Item
4-2
Description
Item
Description
1
Power cord connector
7
Unit Identification (UID) LED/button
2
Power supply LED
8
Video connector
3
Optional redundant power supply bay
9
Parallel port connector
4
RJ-45 Ethernet connector
10
Serial port connector
5
SCSI connector knockouts
11
Keyboard connector
6
USB port connectors (2)
12
Mouse connector
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
Connectors, Switches, and LEDs
System Board Components
Figure 4-2 and Table 4-2 show and describe the location of the components on the server
system board.
32
31
1
2
3
4
30
5
29
28
6
24
7
27
26
23
22
8
22
9
25
21
10
20
11
19
18
17
16
15
14
13
12
Figure 4-2: System board components
Table 4-2: System Board Components
Item
Description
Item
Description
1
Power supply connectors
17
32-bit 33-MHz PCI slot
2
(PPM) Module socket 1 (populated)
18
64-bit 100-MHz PCI-X slot, bus 5
3
Processor socket 1 (populated)
19
64-bit 100-MHz PCI-X slot, bus 5
4
Processor socket 2
20
64-bit 100-MHz PCI-X slot, bus 2
5
Diskette drive connector
21
64-bit 100-MHz PCI-X slot, bus 2
6
Primary IDE connector
22
Battery
7
Secondary IDE
23
CPU fan connector (rear)
8
Power button connector
24
DIMM sockets
9
I/O fan connector (front)
25
USB port connectors
10
Secondary B SCSI
26
RJ-45 Ethernet connector
11
Primary A SCSI
27
Unit ID LED/button
12
(PPM) Module socket 2
28
Video connector
13
Non-maskable interrupt (NMI) switch
29
Parallel port connector
14
RILOE II connector (30 pin)
30
Serial port connector
15
System ID switch
31
Mouse connector
16
System configuration switch
32
Keyboard connector
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
4-3
Connectors, Switches, and LEDs
Switches
System Configuration Switch Settings
The server system board has two sets of switches, an 8-position configuration switch and a
4-position system ID switch. Figure 4-3, Table 4-3 and Table 4-4 show and describe the use
of each switch.
on
on
1 2 3 4 5 6 7 8
1 2 3 4
Figure 4-3: System configuration switch settings
4-4
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
Connectors, Switches, and LEDs
Table 4-3: System Configuration Switch Settings
Switch
Default Position
Function
Description
Settings
1
Off
Reserved
N/A
N/A
2
Off
Lock configuration
Enables or disables the
ability to write to
NVRAM to reconfigure
the system
Off = Configuration may be
changed.
Tower or rack
configuration
Specifies a tower or
rack configuration
Off = Tower configuration
Enable diskette
boot
Enables or disables
booting from the
diskette drive
Off = Diskette drive boot is
controlled by the configuration.
Disables password
Off = Password is enabled.
3
4
5
Off
Off
Off
Password disable
On = Configuration is locked and
cannot be changed.
On = Rack configuration
On = Diskette boot is disabled.
On = Password is disabled.
6
Off
Clear CMOS and
NVRAM
Clears system
configuration settings
Off = Normal
On = When server is powered up,
all system configuration
information is erased.
7
Off
Reserved
N/A
N/A
8
Off
Reserved
N/A
N/A
Note: Switch positions 7 and 8 are reserved for Compaq authorized service providers only. Do not change the
specified default setting for these positions, unless instructed otherwise.
Table 4-4: System ID Switch Settings
Position
Default
Function/Description
1
Off
Reserved
2
Off
Reserved
3
Off
Reserved
4
Off
Reserved
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
4-5
Connectors, Switches, and LEDs
Resetting System Configuration Settings
It may be necessary at some time to clear and reset system configuration settings. When the
system configuration switch position 6 is set to the on position, the system is prepared to
erase all system configuration settings from both CMOS and nonvolatile RAM (NVRAM):
IMPORTANT: Clearing NVRAM deletes the configuration information. Refer to the Compaq ProLiant
ML350 Generation 3 Server Setup and Installation Guide for complete instructions on configuring the
server.
1. Power down the server.
2. Set the system configuration switch position 6 to the on position.
3. Power up the server. All configuration settings are now erased and all system operations
halt.
4. Power down the server.
5. Reset the position 6 switch to the default off position.
6. Power up the server.
7. Reset all system configuration settings.
Refer to Chapter 3 of this guide, “Diagnostic Tools,” or refer to the Compaq ROM-Based
Setup Utility User Guide found on the server documentation CD for more information on
RBSU.
4-6
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
Connectors, Switches, and LEDs
LEDs
Several status LEDs and buttons are located on the front and back of the server. Problem
diagnosis is aided by the LEDs that indicate the status of the components and operations of
the server. LEDs are also located on the system board. The following server LEDs and
buttons are explained in this section
• Power button
• System status LEDs (on the front of the server)
— Power On/Standby and AC power status
— Network Interface Controller (NIC) activity
— External health
— Internal health
— Unit Identification
• Unit Identification (UID) button
• System board LEDs
— Processor failure
— Processor Power Module (PPM) failure
— Memory failure
— Thermal failure
— Fan failure
• Hot-plug hard drive LEDs
• Network Interface Controller LEDs (on the back of the server)
— Network activity status
— Network link
— Connection speed
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
4-7
Connectors, Switches, and LEDs
Power Button, System Status LEDs, and Unit Identification Button
The power button, system status LEDs, and UID button are located on the front of the server.
The power button:
• Powers up the server.
• Places the server in standby mode.
• Powers down the server.
The following system status LEDs are explained:
• Power On/Standby status
• NIC
• External health
• Internal health
• UID
• Hard drive status
The UID button:
• Activates identification.
• Deactivates identification.
• Indicates activation remotely.
4-8
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
Connectors, Switches, and LEDs
1
2
5
3
4
6
7
Figure 4-4: Power button, system status LEDs, and Unit
Identification button
Table 4-5: Power Button, System Status LEDs, and Unit Identification Button
Item
Description
Status
Description
1
UID button
N/A
Allows the user to activate or
deactivate unit identification.
Pushing the button activates unit
identification, shown by the blue
UID LED, so that the onsite
administrator can identify a
particular server.
2
UID LED
Off
Identification off
Blue
Identification on
Flashing blue
Remote console activity
Off
System off and last health good
Green
System on, AC power available,
health good
Amber
System degraded; system on or
system off with auxiliary power
Red
System critical; system on or
system off with auxiliary power
Off
System off
Green
System on; AC power available
Amber
System degraded; on or off with
auxiliary power (One redundant
power supply has failed)
Red
System critical; on or off with
auxiliary power
3
4
Internal health
External health
continued
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
4-9
Connectors, Switches, and LEDs
Table 4-5: Power Button, System Status LEDs, and Unit Identification Button
continued
Item
5
6
7
Description
Status
Description
NIC LED
Off
No connection
Green
Linked to network
Flashing green
System linked and activity present
on network
Off
System off, no AC power
Amber
System is shut down but power is
applied
Green
System is on with AC power
applied
Flashing green
System in standby mode. AC
power available. Do not remove
power from system.
N/A
Allows the user to power up the
server, place the server in standby
mode, and power down the server.
Power On/Standby and AC
power status LED
Power button
CAUTION: When the power LED is green, it is unsafe to remove AC power from the
system without performing a proper shutdown of the operating system.
4-10
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
Connectors, Switches, and LEDs
System Board LEDs
Figure 4-5 and Table 4-6 show and describe LEDs on the system board of the server that
indicate when a processor, PPM, memory module, or fan fails. System board LEDs also
indicate when the Server Feature Board is not properly seated or when a thermal threshold is
exceeded.
1
2
3
4
15
5
14
6
7
8
13
12
11
10
9
Figure 4-5: System board LEDs
Table 4-6: System Board LEDs
Item
1
Description
Status
AC power
Off = No AC power, poor power supply, or power
supply current limits exceeded
Green = Power supply is powered on and
functioning, or power supplied by auxiliary power
2
PPM 1 status
Off = PPM 1 functioning
Amber = PPM 1 failed
3
Processor 1 thermal
Off = Normal
Amber = Thermal trip detected for processor 1.
Refer to the Compaq ProLiant ML350 Generation 3
Server Setup and Installation Guide for the
appropriate instructions.
4
Processor 1 status
Off = Processor 1 functioning
Amber = Processor 1 failed
continued
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
4-11
Connectors, Switches, and LEDs
Table 4-6: System Board LEDs continued
Item
5
Description
Status
I/O fan status
Off = Fan functioning
Amber = Fan is not installed or has failed
6
Processor 2 status
Off = Processor 2 functioning
Amber = Processor 2 failed
7
Processor 2 thermal
Off = Normal
Amber = Thermal trip detected for processor 2.
Refer to the Compaq ProLiant ML350 Generation 3
Server Setup and Installation Guide for the
appropriate instructions.
8
PPM 2 status
Off = PPM 2 functioning
Amber = PPM 2 failed
9
PCI-X bus 2 speed
Off = PCI 33 MHz/PCI-X 66 MHz operating mode
On = PCI 66 MHz/PCI-X 100 MHz operating mode
10
PCI-X bus 2 mode
Off = PCI-X mode is inactive
On = PCI-X mode is active
11
Temperature threshold
Off = Normal
Amber = Temperature threshold exceeded
12
PCI-X bus 5 speed
Off = PCI 33 MHz/PCI-X 66 MHz operating mode
On = PCI 66 MHz/PCI-X 100 MHz operating mode
13
PCI-X bus 5 mode
Off = PCI-X mode is inactive
On = PCI-X mode is active
14
CPU fan status
Off = Fan functioning
Amber = Fan is not installed or has failed
15
4-12
DIMM status (DIMM slots 1
through 4)
Off = DIMM functioning
Amber = DIMM failed
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
Connectors, Switches, and LEDs
Hot-Plug Hard Drive LEDs
The hot-plug SCSI hard drive LEDs, located on each physical drive, are visible on the front
of the server or external storage unit. They provide status information regarding drive
activity (1), connectivity (2), and fault (3) status for each corresponding drive when
configured as part of an array and connected to an array controller. Their behavior may vary,
depending on the status of other drives in the array. Use the illustration in Figure 4-6 in
conjunction with Table 4-7 to analyze current status for hot-plug hard drives that are
connected to an array controller.
CAUTION: To avoid data loss, read “Hot-Plug Hard Drive Replacement Guidelines” in the
Compaq Servers Troubleshooting Guide before removing a hard drive.
1
2
3
Figure 4-6: Hot-plug hard drive LEDs
For additional information on troubleshooting hard drive problems, refer to “Hard Drive
Problems” and “SCSI Device Problems” in the Compaq Servers Troubleshooting Guide.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
4-13
Connectors, Switches, and LEDs
Table 4-7: Hot-Plug SCSI Hard Drive LED Combinations
Activity
Online
Fault
Meaning
On
Off
Off
Do not remove the drive. Removing a
drive during this process causes data
loss.
The drive is being accessed and is not
configured as part of an array.
On
Flashing
Off
Do not remove the drive. Removing a
drive during this process causes data
loss.
The drive is rebuilding or undergoing
capacity expansion.
Flashing
Flashing
Flashing
Do not remove the drive. Removing a
drive during this process causes data
loss.
The drive is part of an array being selected
by the Array Configuration utility (ACU).
-OrThe Options ROMPaq is upgrading the
drive.
Off
Off
Off
It is OK to replace the drive online if a
predictive failure alert is received (refer to
the “Predictive Failure Alert” section in the
Compaq Servers Troubleshooting Guide for
details) and the drive is connected to an
array controller.
The drive is not configured as part of an
array.
-OrIf this drive is part of an array, a
powered-up controller is not accessing the
drive.
-OrThe drive is configured as an online spare.
Off
Off
On
It is OK to replace the drive online.
The drive has failed and has been placed
offline.
continued
4-14
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
Connectors, Switches, and LEDs
Table 4-7: Hot-Plug SCSI Hard Drive LED Combinations continued
Activity
Online
Fault
Meaning
Off
On
Off
OK to replace the drive online if a predictive
failure alert is received (refer to the
“Predictive Failure Alert” section in the
Compaq Servers Troubleshooting Guide for
details), provided that the array is
configured for fault tolerance and all other
drives in the array are online.
The drive is online and is configured as part
of an array.
Off
On
Off
OK to replace the drive online if a predictive
failure alert is received (refer to the
“Predictive Failure Alert” section in the
Compaq Servers Troubleshooting Guide for
details), provided that the array is
configured for fault tolerance and all other
drives in the array are online.
The drive is online and is configured as part
of an array.
On or flashing
On
Off
OK to replace the drive online if a predictive
failure alert is received (refer to the
“Predictive Failure Alert” section in the
Compaq Servers Troubleshooting Guide for
details), provided that the array is
configured for fault tolerance and all other
drives in the array are online.
The drive is online and is being accessed.
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
4-15
Connectors, Switches, and LEDs
Network Interface Controller LEDs
The NIC LEDs are located on the back of the server. They provide the following information:
• The speed at which the network is being accessed
• If the server is linked to the network
• If there is current network activity
Refer to the Compaq Servers Troubleshooting Guide for more information on troubleshooting
network controller problems.
1
2
Figure 4-7: NIC LEDs
Table 4-8: NIC LEDs
Item
1
2
4-16
Description
Status
Condition
Activity
Off
No network activity
Green blinking
Linked and activity on the network
Off
No network link
Green
Linked to network
Link
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
5
Physical and Operating Specifications
This chapter provides physical and operating specifications for the Compaq ProLiant ML350
Generation 3 server. The following specifications are provided:
•
System unit
•
Rack server system unit
•
Memory
•
1.44-MB Diskette drive
•
IDE CD-ROM drive
•
Wide Ultra3 SCSI hot-plug hard drives
•
Integrated Compaq NC7760 gigabit server auto-switching NIC
•
Integrated dual channel Wide Ultra3 SCSI adapter
•
Remote Insight Lights-Out Edition II option board
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
5-1
Physical and Operating Specifications
System Unit
Table 5-1: System Unit Specifications
Item
Description
Height (without feet)
44.5 cm (17.5 in)
Height (with feet)
46.99 cm (18.5 in)
Depth (without bezel)
60.96 cm (24.0 in)
Depth (with bezel)
66.04 cm (26.0 in)
Width (without feet)
21.59 cm (8.5 in)
Width (with feet)
26.04 cm (10.25 in)
Weight (no drives installed)
27.24 kg (60.0 lb)
Input requirements
International Units (English Units)
Rated input voltage
200 VAC to 240 VAC (100 VAC to 120 VAC)
Rated input frequency
50 Hz to 60 Hz
Rated input current
3.7 A (7.4 A)
Rated input power
538 W
BTUs per hour
1,839
Power supply output
Rated steady-state power
500 W
Temperature range
Operating
10°C to 35°C (50°F to 95°F)
Shipping
-40°C to 70°C (-40°F to 158°F)
Relative humidity (noncondensing)
Operating
10% to 90%
Nonoperating
5% to 95%
Wet-bulb temperature
Maximum
28°C (82.4°F)
Acoustic noise
5-2
Idle (hard drives spinning)
6.4 NPEL (BELS)/45 AVERAGE SPL (dba)
Operating (random seeks to hard drives)
6.7 NPEL (BELS)/49 AVERAGE SPL (dba)
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
Physical and Operating Specifications
Rack Server System Unit
Table 5-2: Rack Server System Unit Specifications
Feature
International Units (English Units)
Dimensions
Height
21.87 cm (8.61 in)
Depth
60.96 cm (24 in)
Width
48.26 cm (19.0 in)
Weight (no drives installed)
27.24 kg (60 lb)
Input requirements
Rated input voltage
200 VAC to 240 VAC (100 VAC to 120 VAC)
Rated input frequency
50 Hz to 60 Hz
Rated input current
3.7 A (7.4 A)
Rated input power
538 W
BTUs per hour
1,839
Power supply output
Rated steady-state power
500 W
Temperature range
Operating
10°C to 35°C (50°F to 95°F)
Shipping
-40°C to 70°C (-40°F to 158°F)
Relative humidity (noncondensing)
Operating
10% to 90%
Nonoperating
5% to 95%
Wet-bulb temperature
Maximum
28°C (82.4°F)
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
5-3
Physical and Operating Specifications
Memory
Table 5-3: Memory Specifications
Item
Description
Size
128 MB, 256 MB, 512 MB, 1 GB and 2 GB
Speed
266 MHz
Type
PC2100 ECC Registered DDR SDRAM DIMMs
Note: DIMMs must be industry-standard 184-pin PC2100 DDR DIMMs. The DDR DIMMs must
support CAS Latency 2 or greater. They must also contain the mandatory Joint Electronic Device
Engineering Council (JEDEC) Serial Presence Detect (SPD).
1.44-MB Diskette Drive
Table 5-4: 1.44-M Diskette Drive Specifications
Item
Description
Size
88.9 mm (3.5 in)
LED (front panel)
Green
Read/write capacity per diskette
(high/low density)
1.44 MB/720 KB
Drives supported
1
Drive height
15.2 mm (0.6 inch)
Drive rotation
300 rpm
Transfer rate bits/sec (high/low)
500/250 Kbps
Bytes/sector
512
Sectors/track (high/low)
18/9
Tracks/side (high/low)
80/80
Access times
5-4
Track-to-track (high/low)
6 ms/3 ms
Average (high/low)
174 ms/94 ms
Settling time
15 ms
Latency average
100 ms
Cylinders (high/low)
80/80
Read/write heads
2
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
Physical and Operating Specifications
IDE CD-ROM Drive
Table 5-5: IDE CD-ROM Drive Specifications
Item
Description
Applicable disk
CD-DA, CD-RW, Photo CD (single and multisession), CD-XA Ready, Cdi
Ready
Capacity
540 MB (mode 1, 12 cm)
650 MB (mode 2, 12 cm)
Block size
2,048 bytes (mode 1); 2,340; 2336 bytes (mode 2); 2,352 bytes (CD-DA);
2,328 (CD-XA)
Dimensions
Height
12.7 mm (0.5 in)
Width
130 mm (5.11 in)
Depth
131 mm (5.16 in)
Weight
<1,200 g (<42.4 oz)
Data transfer rate
Sustained
150 KBps (sustained 1X)
Burst
2,500 KBps to 6,000 KBps
Bus rate
48 MBps
Access times
(typical)
Full stroke
<100 ms
Random
<150 ms
Disk diameter
12 cm, 8 cm (4.7 in, 3.15 in)
Disk thickness
1.2 mm, 0.05 cm (0.047 in x 0.20 in)
Track pitch
1.6 µm
Cache/buffer
128 KB
Startup time
<7s (single session); <30s (multisession)
Stop time
<4s
Operating conditions
Temperature
5°C to 45°C (41°F to 110°F)
Humidity
10% to 80%
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
5-5
Physical and Operating Specifications
Wide Ultra3 SCSI Hot-Plug Hard Drives
Table 5-6: Wide Ultra3 SCSI Hard Drive Specifications
Item
9-GB Drive
18-GB Drive
36-GB Drive
72-GB Drive
Capacity
9100.0 MB
18,209.8 MB
36,419.6 MB
72,839.2 MB
Height
One-third, 1.0 in
One-third, 1.0 in
One-third, 1.0 in
One-third, 1.0 in
Size
3.5 in
3.5 in
3.5 in
3.5 in
Interface
Wide Ultra3
Wide Ultra3
Wide Ultra3
Wide Ultra3
Transfer Rate
160 MBps
160 MBps
160 MBps
160 MBps
Rotational Speed
10,000 RPM
10,000 RPM
10,000 RPM
10,000 RPM
Bytes per sector
512
512
512
512
Logical Blocks
17,773,524
35,566,080
71,132,000
142,264,000
Operating
Temperature
10°C to 35°C
(50°F to 95°F)
10°C to 35°C
(50°F to 95°F)
10°C to 35°C
(50°F to 95°F)
10°C to 35°C
(50°F to 95°F)
Integrated Compaq NC7760 Gigabit Server Auto-switching NIC
Table 5-7: Integrated Compaq NC7760 Gigabit Server Auto-switching NIC
Specifications
5-6
Item
Description
Network interface
10Base-T/100Base-TX/1000Base-T Ethernet
Compatibility
IEEE 802.2, 802,3, 803.3u
Data transfer method
32-bit, PC 33-MHz bus master
Network transfer rate
10/100/1000 Mbps
Connector
RJ-45
I/O address and interrupt
Plug and Play PCI
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
Physical and Operating Specifications
Integrated Dual Channel Wide Ultra3 SCSI Adapter
Table 5-8: Integrated Dual Channel Wide Ultra3 SCSI Adapter Specifications
Item
Description
Protocol
Wide Ultra160 SCSI, Wide Ultra3 SCSI, Wide Ultra SCSI,
Fast-Wide SCSI-2, and Fast SCSI-2
Compatibility
All PCI server configurations are backward compatible with Fast,
Fast-Wide SCSI-2, Wide Ultra2 SCSI, and Wide Ultra3 SCSI devices
Drives supported
Up to 15 SCSI devices per channel
Data transfer method
32-bit PCI bus master
Maximum transfer rate
per PCI bus
133 MBps
SCSI channel transfer
rate
160 MBps
SCSI termination
Active termination
SCSI connectors
2 internal (68-pin)
Capacity
509.6 GB
Height
1.0 in
Size
3.5 in
Interface
Wide Ultra3 SCSI
Seek time
Single track
0.8 ms
Average
7.9 ms
Full stroke
17.0 ms
Rotational speed
7,200 rpm
Physical configuration
Bytes/sector
512
Logical blocks
17,773,524
Operating temperature
10°C to 35°C (50°F to 95°F)
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
5-7
Physical and Operating Specifications
Remote Insight Lights-Out Edition II Option Board
Table 5-9: Remote Insight Lights-out Edition II Option Board Specifications
5-8
Item
Description
Architecture
32-bit PCI-based remote management board
(For the ProLiant ML350 Generation 3 server,
install the board in the 32-bit PCI slot.)
Processor
IBM 405 GP 200 Mhz (Power PC)
Memory
32-MB SDRAM, 4-MB Flash ROM
Upgradability
Option firmware upgradable using flash ROM
Video support
ATI Rage XL, supporting modes:
•
640 x 480 (256 to 16.7 M colors)
•
800 x 600 (256 to 16.7 M colors)
•
1,024 x 768 (256 to 65 K colors)
•
1,280 x 1,024 (256 colors)
Connectors
External power, keyboard/mouse, video,
Ethernet network connection (10/100 Mbps)
External power adapter
10 VDC, 1.5 A
Remote Insight operating system support
Go to
www.compaq.com/manage/
remote-lightsout.html
Remote Insight client browser support
Microsoft Internet Explorer 5.0, Netscape
Navigator 6.01, or any other
Java 1.1-compliant browser software
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon Part Number: 278704-002 Last Saved On: 12/18/02 9:49 AM
Index
A
AC power, caution 4-10
access panel
part number 1-3
removing 2-7
replacing 2-7
ADU (Array Diagnostics Utility) 3-4
air baffle
part number 1-3
removing 2-15
replacing 2-15
Array Diagnostics Utility See ADU
ASR (Automatic Server Recovery), running 3-3
Automatic Server Recovery See ASR
B
battery
handling, warning 2-37
part number 1-5
system board 2-37
system board, location 2-38
system board, replacing 2-38
bezel (rack)
part number 1-3
removing 2-8
removing, illustrated 2-10
replacing 2-10
bezel door (tower)
part number 1-3
removing 2-6
replacing 2-6
boards, part numbers 1-5
C
cable routing
caution 2-12
diagrams 2-12
cautions
AC power 4-10
cable routing 2-12
ESD 2-4, 2-30, 2-32, 2-37
handling components 2-29
handling memory modules 2-29
hot-plug hard drive replacement 4-13
power fluctuations 2-4
processor locking lever 2-34
proper cooling 2-4
removing access panel 2-29
CMOS, clearing 4-6
Compaq authorized reseller vii
Compaq Insight Manager 3-1
Compaq website vii
component-level repairs vi
component-level repairs, warning 2-4
connectors, overview 4-2
connectors, switches, and LEDs 4-1
cooling, caution 2-4
country kit, part number 1-6
cover kit
contents 1-3
part number 1-3
CPU fan module
part number 1-5
removing 2-16
status LED 4-12
D
data transfer rate, IDE CD-ROM drive 5-5
diagnostic tools utility overview 3-1
Diagnostics Utility
accessing 3-1
locating 3-1
DIMM, status LEDs 4-12
diskette drive
access times 5-4
dimensions 5-4
part number 1-5
diskette drive cable assembly, part number 1-6
drive bay configuration, illustrated 2-19
drivers, installing 3-4
dual channel Wide Ultra160 SCSI adapter,
capacity 5-7
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:51 AM
Index-1
Index
symbol 2-3
warning 2-3, 2-4, 2-35
hot-plug hard drive
LEDs, illustrated 4-13
removing 2-21
replacing 2-21
replacing, caution 4-13
hot-plug hard drive blank
part number 1-3
removing 2-20
replacing 2-20
hot-plug hard drive cage
part number 1-3, 1-5
removing 2-22
replacing 2-23
E
electric shock
symbol 2-3
warning 2-3
electrostatic discharge See ESD
ESD (electrostatic discharge)
caution 2-4, 2-32, 2-37
packaging 2-2
preventing 2-2
sensitive parts 2-2
storing 2-2
tools recommended 2-2
transporting 2-2
work area recommendations 2-2
event log
described 3-4
viewing 3-4
expansion board
removing 2-27
replacing 2-28
expansion board guide, part number 1-3
expansion board retainer
part number 1-3
removing, illustrated 2-27
exploded view, mechanical parts 1-2
I
F
fan See system fan module
feet
part number 1-3
removing 2-41
replacing 2-41
front faceplate and bezel (rack), part number 1-3
G
grounding
caution vi
grounding plug vi
techniques 2-2
H
hard drive LEDs
activity 4-14, 4-15
fault 4-14, 4-15
online 4-14, 4-15
hazard symbol 2-3
hazardous conditions See symbols on equipment
hazardous energy circuits symbol 2-3
heavy weight
warning 2-3
help resources vii
hood panel, part number 1-3
hot surface
Index-2
I/O fan module
part number 1-5
removing 2-18
status LED 4-12
ID switch
location 4-4
settings 4-5
IDE CD-ROM drive
access times 5-5
block size 5-5
capacity 5-5
dimensions 5-5
disk specifications 5-5
operating conditions 5-5
part number 1-5
signal cable routing, illustrated 2-13
transfer, rate 5-5
weight 5-5
IDE CD-ROM Drive
specifications 5-5
IDE ribbon cable assembly, part number 1-6
IML (Integrated Management Log), described 3-4
indicators See LEDs
INSPECT
accessing 3-4
described 3-4
IRQ conflict, resolving 3-3
K
keyboard, part number 1-6
kits
country, part number 1-6
cover, part number 1-3
miscellaneous plastics, part number 1-3
return (rack), part number 1-6
return (tower), part number 1-6
signal cable, part number 1-6
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:51 AM
Index
tower-to-rack conversion, part number 1-6
L
labels See symbols on equipment
LEDs
CPU fan status 4-12
DIMM status 4-12
external health 4-9
hard drive, activity 4-14, 4-15
hard drive, fault 4-14, 4-15
hard drive, online 4-14, 4-15
hard drive, table of combinations 4-14, 4-15
hot-plug hard drive, illustrated 4-13
I/O fan status 4-12
internal health 4-9
network activity 4-16
network link 4-16
network speed 4-16
NIC (Network Interface Connector) 4-10
NIC, illustrated 4-16
NIC, summary 4-16
overview 4-7
Power On/Standby 4-10
power supply 4-11
PPM 1 status 4-11
PPM 2 status 4-12
processor 1 status 4-11
processor 1 thermal 4-11
processor 2 status 4-12
processor 2 thermal 4-12
system board 4-11
system status 4-8
temperature threshold 4-12
Unit Identification (UID) 4-9
M
mass storage devices, part number 1-5
mechanical parts
illustrated 1-2
spare parts list 1-3
media device blank
removing 2-11
replacing 2-11
memory modules
installation guidelines 2-29
part number 1-5
removing 2-30
replacing 2-30
size 5-4
socket locations, illustrated 2-29
speed 5-4
miscellaneous plastics kit, part number 1-3
miscellaneous, part numbers 1-6
N
NIC (Network Interface Controller)
activity LED 4-16
LEDs, illustrated 4-16
LEDs, summary 4-16
link LED 4-16
NVRAM (nonvolatile RAM), clearing 4-6
O
options, part numbers 1-5
P
part numbers
access panel 1-3
air baffle 1-3
battery 1-5
bezel door (tower) 1-3
boards 1-5
country kit 1-6
cover kit 1-3
CPU fan module 1-5
diskette drive 1-5
diskette drive cable assembly 1-6
expansion board guide 1-3
expansion board retainer 1-3
feet 1-3
front faceplate and bezel (rack) 1-3
hood panel 1-3
hot-plug hard drive blank 1-3
hot-plug hard drive cage 1-3, 1-5
I/O fan module 1-5
IDE CD-ROM drive 1-5
IDE ribbon cable assembly 1-6
keyboard 1-6
mass storage devices 1-5
memory modules 1-5
miscellaneous 1-6
miscellaneous plastics kit 1-3
options 1-5
power 1-5
power supply backplane board cover 1-3
power supply backplane board with cover 1-5
power supply blank 1-3
power supply with power factor correction 1-5
power switch assembly 1-5
PPM 1-5
processor 1-5
rackmount hardware kit with rails 1-3
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:51 AM
Index-3
Index
removable media device blank 1-3
removable media device SCSI cable 1-6
retainer clips 1-3
return kit (rack) 1-6
return kit (tower) 1-6
SCSI Point-to-Point cable 1-6
signal cable kit 1-6
system board 1-5
top panel 1-3
tower-to-rack conversion kit 1-6
parts
catalog, illustrated 1-1
handling 2-2
storing 2-2
transporting 2-2
PCI boards, configuring automatically 3-3
personal injury, warning 2-4
POST
described 3-3
running 3-3
power button
location 4-10
summary 4-8
power cords, disconnecting, warning 2-4
power fluctuations, caution 2-4
Power On/Standby status, LED 4-10
power sources symbol 2-3
power supply
blank, part number 1-3
LEDs 4-11
removing 2-39
replacing 2-39
power supply backplane board
removing 2-40
replacing 2-40
power supply backplane board cover, part
number 1-3
power supply backplane board with cover
part number 1-5
power supply with power factor correction, part
number 1-5
power switch assembly, part number 1-5
power warning 2-3
power, part number 1-5
power-down procedures 2-4
Power-On Self-Test See POST
PPM (Processor Power Module)
part number 1-5
Processor Power Module 1, LEDs 4-11
Processor Power Module 2, LEDs 4-12
removing 2-35
replacing 2-35
Index-4
socket locations, illustrated 2-31
warning 2-35
processor
caution 2-34
part number 1-5
removing 2-32
replacing 2-34
socket locations, illustrated 2-31
processor 1
LEDs, status 4-11
LEDs, thermal 4-11
processor 2
LEDs, status 4-12
LEDs, thermal 4-12
Processor Power Module See PPM
R
rack server system unit
dimensions 5-3
input voltage requirements 5-3
power supply output 5-3
relative humidity 5-3
temperature range 5-3
wet-bulb temperature 5-3
rack stability, warning 2-5
rackmount hardware kit with rails, part number 1-3
RBSU (ROM-Based Setup Utility)
description 3-3
running 3-3
rear panel components 4-2
removable media device
removing 2-24
replacing 2-25
SCSI cable, part number 1-6
signal cable routing, illustrated 2-13
removable media device blank, part number 1-3
removal and replacement procedures 2-1
resource conflict, resolving 3-3
retainer clips, part number 1-3
return kit (rack), part number 1-6
return kit (tower), part number 1-6
RJ-45 receptacle symbol 2-3
RJ-45 receptacle, warning 2-3
ROM-Based Setup Utility See RBSU
ROMPaq Utility, running 3-2
S
screwdriver symbol 2-3
SCSI LVD hard drive
Point-to-Point cable routing 2-14
Point-to-Point cable, part number 1-6
signal cable kit, part number 1-6
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:51 AM
Index
SmartStart Diskette Builder
description 3-2
running 3-2
SmartStart software 3-2
specifications
IDE CD-ROM Drive 5-5
NIC 5-6
physical and operating, overview 5-1
Remote Insight Lights-out Edition board 5-8
Ultra160 SCSI Adapter 5-7
Wide Ultra3 SCSI hot-plug hard drive 5-6
standby
activating 2-5
effects 2-4
Survey Utility
description 3-2
installing 3-2
symbols
in text v
on equipment 2-3
system board
components 4-3
configuration switch settings 4-5
ID switch settings 4-5
LEDs 4-11
part number 1-5
removing 2-36
replacing 2-36
switches 4-4
system components
exploded view 1-4
illustrated 1-4
spare parts list 1-5, 1-6
system configuration switch
CMOS, clearing 4-6
location 4-4
NVRAM, clearing 4-6
settings 4-5
system fan modules, connector locations 2-16
System Firmware Update 3-3
system status LEDs
location 4-9
summary 4-8
system unit
acoustic noise 5-2
input voltage requirements 5-2
power supply output 5-2
relative humidity 5-2
specifications 5-2
temperature range 5-2
wet-bulb temperature 5-2
telephone symbol 2-3
temperature threshold LED 4-12
text conventions viii
tools recommended for servicing 2-1
top panel, part number 1-3
tower-to-rack conversion kit, part number 1-6
U
Unit Identification button (UID)
described 4-9
summary 4-8
utilities
ADU (Array Diagnostics Utility) 3-4
ASR (Automatic Server Recovery) 3-3
Compaq Insight Manager 3-1
Diagnostics 3-1
IML 3-4
INSPECT 3-4
overview 3-1
POST 3-3
RBSU (ROM-Based Setup Utility) 3-3
ROMPaq 3-2
SmartStart Diskette Builder 3-2
SmartStart software 3-2
Survey Utility 3-2
V
ventilation clearances vi
W
warnings
battery handling 2-37
component-level repairs 2-4
disconnecting power cords 2-4
electric shock 2-3
heavy weight 2-3
hot surface 2-3, 2-4, 2-35
improper repairs 2-4
multiple sources of power 2-3
personal injury 2-4
rack stability 2-5
RJ-45 receptacle 2-3
technician notes 2-4
warranty, voiding vi
weight
symbol 2-3
warning 2-3
T
technician notes vi
telephone numbers vii
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:51 AM
Index-5
Index
Wide Ultra160 SCSI hard drive
operating temperature 5-7
physical configuration 5-7
seek time 5-7
Index-6
Wide Ultra3 SCSI hot-plug hard drive
specifications 5-6
work area recommendations 2-2
wrist strap, using 2-2
Compaq ProLiant ML350 Generation 3 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL Codename: Steel Dragon 2.4 Part Number: 278704-002 Last Saved On: 12/18/02 9:51 AM
Download PDF

advertising