Owner`s manual | Conair CID110 Telephone User Manual

Caller ID* Telephone
with 10-Memory Dialing
*You must subscribe to Caller ID service from your local
telephone company to receive Caller Identification.
Service Center
©2003 CONAIR CORPORATION
7475 N. Glen Harbor Blvd., Glendale, AZ 85307
NLM055Y2
Printed in China
HOTLINE 1-800-366-0937
IB-4577B
CID110 Owner’s Manual
IMPORTANT SAFETY INSTRUCTIONS
LOCATION OF CONTROLS
When using your telephone equipment, basic safety precautions
should always be followed to reduce the risk of fire, electric shock
and injury to persons, including the following:
1. Do not use this product near water, for example, near a bath
tub, wash bowl, kitchen sink or laundry tub, in a wet basement
or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during
an electrical storm. There may be a remote risk of electric
shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity
of the leak.
4. Use only the power cord and batteries indicated in this manual.
Do not dispose of batteries in a fire. They may explode. Check
with local codes for possible special disposal instructions.
CONGRATULATIONS!
You have purchased a CID110, Caller ID Telephone with 10Memory Dialing manufactured to the highest standards of
ConairphoneTM. Before installing and operating, be sure to read
this manual.
1
10
2
3
GENERAL INFORMATION
11
12
13
4
14
15
16
5
6
7
8
SAVE THESE INSTRUCTIONS
1
This package contains:
• CID110 Caller ID Telephone with 10-Memory Dialing
• Owner’s Manual
• Fully Modular Coil Cord
• Fully Modular Telephone Line Cord (Long Straight Cord)
• Fully Modular Telephone Line Cord (Short Straight Cord)
• Quick Installation Guide
• Important Notice
• Two (2) Memory Index Labels
• Warranty Card
If anything is missing or damaged, contact the place of purchase.
Keep the packaging to transport telephone.
9
1.
2.
3.
4.
5.
6.
7.
8.
9.
UNPACKING
10. New Call LED
11. Ringer Hi/Lo/Off Switch
12. LCD Display
13. Battery Compartment
Receiver
Receiver Volume Control
Hook Switch
Keypad
Tone/Pulse Switch
Redial Button
Transmitter / Mic
Store Button
Memory Button
14. Review / Button
15. Erase Button
16. Call Back Button
2
For your reference, keep a record of the date purchased.
Please save the sales receipt for the warranty reference.
Date of Purchase ___________________________
INSTALLATION INSTRUCTIONS
Follow these precautions:
a. Never install telephone wiring during a lightning storm.
b. Never install telephone jacks in wet locations unless the jack
is specifically designed for wet locations.
c. Never touch uninsulated telephone wires or terminals unless
the incoming telephone line has been disconnected at the
network interface.
d. Use caution when installing or modifying telephone lines.
3
TO INSTALL BATTERIES
Batteries are required for the Caller ID functions and Telephone
operations of the unit.
1. Open the battery door by pulling back the latch.
2. Insert three (3) AA alkaline batteries (not included).
3. Snap the battery door back into place.
Note: Once batteries are installed, you have 20 seconds to setup
the Caller ID.
SETTING UP YOUR CID110
DO NOT CONNECT the line cord to the wall outlet until the
Caller ID setup has been completed.
NOTES:
• If the Caller ID is not setup within 20 seconds after battery
installation, press and hold both the [ ] and [ ] keys for 4
seconds to activate the Caller ID setup.
• If you do not have the Caller ID service and want the time/
date set, please go to Caller ID setup section and ‘ENTER
TIME DATE’ setting.
The LCD shows ‘ENTER LANGUAGE’
followed by a choice of 3 languages
(English, Spanish, French).
The LCD then shows ‘ENG ESP FRA’.
NOTE: The ‘ENG’ is BLINKING. Press
[ ] or [ ] to select ‘ENG’, ‘ESP’, or ‘FRA’.
Press [ERASE] to confirm.
If ENG is selected, the LCD shows ‘LCD
CONTRAST’.
Press [ ] or [ ] to adjust five levels (from
1 to 5, default is 3) contrast of LCD.
Press [ERASE] to confirm.
If contrast is set, the LCD shows
‘ENTER AREA CODE’. The first digit
‘–’ of the area code will blink.
Press [ ] or [ ] to enter the area code.
Press [ERASE] to confirm and go to next entry.
Repeat above steps until 3-digit area code is set.
4
If area code is set, the LCD shows
‘ENTER TIME DATE’.
Press [ ] or [ ] to select the hour digits.
Press [ERASE] to confirm and go to the next entry.
Press [ ] or [ ] to select the minute
digits.
Press [ERASE] to confirm and go to the
next entry.
Press [ ] or [ ] to select the month digits.
Press [ERASE] to confirm and go to the
next entry.
Press [ ] or [ ] to select the date digits.
Press [ERASE] to confirm.
On a wall without a plate
1. Install 2 screws with anchors into the wall, one above the
other, 3-1/4" apart, extending 3/16" out from the wall to hold
the base securely.
2. Install the long telephone line cord into the jack in the base,
thread it through the groove and plug it into modular wall
jack.
3. Hang the base on the screws and pull it down to lock it on.
4. Plug the coil cord into the handset and base jacks.
TELEPHONE FEATURES
Tone/Pulse Switch
The LCD shows ‘TOTAL:00 NEW:00’,
which means both the total call and new
call counter are zero.
Set switch to your type of service. If you don’t know whether you
have tone or pulse:
1. Put the switch on “Tone”.
2. When you have a dial tone, press any key on the keypad. If
the dial tone stops, leave it on “Tone”. If not, change the setting
to “Pulse”.
USING THE PHONE ON A DESK
Receiver Volume Control
1. Plug the long telephone line cord into the jack in the bottom
of the BASE, thread it through the groove toward the back of
the unit, then plug it into the modular phone jack.
2. Connect the COIL CORD to the jack in the HANDSET and
the BASE.
The receiver volume control is located on the side of the handset
of your phone. This enables you to adjust the receiver volume
from NORM to HI for a better listening level.
Ringer Off/Low/High
When the CID110 is wall mounted, the HANDSET GUIDE holds
the handset in place in the cradle.
Your CID110 features a harmonic dual tone ringer that can be
adjusted from a loud (HI) to a soft (LO) sound level. When you
don’t want to be disturbed, slide the switch to the OFF position.
You can still make outgoing calls without being disturbed by
incoming calls.
On a wall phone plate
Pause
HANGING THE PHONE ON THE WALL
1. Plug the short telephone line cord into the jack in the base
bottom and into the jack on the plate.
2. Hang the base on to the two pins and pull the base down to
lock it on.
3. Plug the coil cord into the handset and base jacks.
Whether you have Tone or Pulse service, you can insert a 4second PAUSE into the dialing or storing of a number into
memory in order to access custom and telebanking services,
long distance, etc. Press [Redial] at the desired point in the
number. Press [Redial] again if an additional 4 seconds is
needed.
5
6
Redial Button
Automatically redials last number called (up to 32 digits). If the
number was busy or unanswered:
1. Lift the HANDSET.
2. Press [Redial].
TELEPHONE OPERATION
Receiving a Call
1. When your phone rings, pick up the handset and use it like
any basic telephone.
2. Hang up the handset to release the telephone line when your
conversation is completed.
Dialing a Call
1. Pick up the phone and wait for a dial tone.
2. Press the keypad for the telephone number you wish to dial.
Tone/Pulse Combination Dialing
Combination dialing is useful to subscribers of Pulse (rotary)
service who wish to gain access to various low-cost longdistance or automated computer services otherwise not available
to them.
1. With the Tone/Pulse switch in the Pulse position, dial the
phone number.
2. Press [ ], and your telephone will change to Tone dialing
mode.
3. Dial your code/authorization number. When your call is
completed, your telephone will automatically return to the
PULSE dialing mode.
NOTE: Combination dialing can also be stored into the memory
for one-touch access to your long distance or automated
computer service.
*
7
BASIC MEMORY PROGRAMMING
The CID110 comes with 10-memory dialing.
NOTE: Your local phone company restricts the time you can
have the handset off the base (off-hook).
YOU SHOULD PROGRAM THE CID110 MEMORY WITH THE
LINE CORD UNPLUGGED FROM THE WALL, IF YOU ARE
GOING TO PROGRAM MORE THAN ONE PHONE NUMBER.
NOTES:
• Pressing [Redial] will place a 4-second PAUSE into the
number. Which may be required for accessing special phone
services.
• You can store a number with up to 16 digits maximum. Only
the last 14 digits will be displayed.
MEMORY DIALING
Press the keypad to enter the number that you want to program.
The LCD on the back of the handset confirms the numbers you
entered.
Pick up the handset to make your call.
Press [MEM] [0] ... [MEM] [9] for one of the 10 memory locations
to be dialed.
NOTE: Remember to plug the telephone line cord back into the
wall.
Press [Store]. The ‘MEM’ will be displayed on the right corner of
LCD.
CALLER ID OPERATION
Pick up the handset, and press [Store] to enter memory store.
Press the memory location (0 to 9) on the keypad. The LCD will
then return to the ‘Answer-Ready’ mode, and display the total
call counter, new call counter, current time and date.
Copy from the Caller ID to Telephone Memory
Press [ ] or [ ] until the Caller ID memory location to be copied
appears on the LCD. Press [Store] twice to enter memory store.
The ‘MEM’ will be displayed on the right corner.
Press the memory location (0 to 9) on the keypad. The LCD will
then return to the ‘Answer-Ready’ mode, and display the total
call counter, new call counter, current time and date.
If no key is pressed within 20 seconds, the LCD will return to
‘Answer-Ready’ mode.
Repeat the above steps to store a different number in the same
speed dial location, or to store a new number in a different speed
dial location.
8
NOTE: Batteries must be installed, or Caller ID operations will
not work properly (see “To Install Batteries”).
If an incorrect, invalid or incomplete
Caller ID signal is received, the LCD
shows ‘-LINE ERROR-’.
If only the caller’s phone number is
received, the LCD shows the caller’s
phone number with the time and date it
was received. The ‘NEW’ icon turns on and New Call LED blinks.
If both the caller’s name and phone
number are received, the LCD shows the
caller’s name and phone number with
the time and date it was received. The ‘NEW’ icon turns on and
New Call LED blinks.
If the name and number are not available
due to the caller’s restriction, the LCD
shows ‘-PRIVATE CALL-’ with the time
and date received. The ‘NEW’ icon turns on and New Call LED
blinks.
9
If the name and number are not
ava i l a b l e, t h e L C D w i l l s h ow
‘-UNAVAILABLE-’ with the call’s time and
date. The ‘NEW’ icon turns on and New Call LED blinks.
If no key is pressed within 20 seconds,
the LCD will show the ‘Answer-Ready’
mode, and display the total call counter,
new call counter, current time and date.
VIEW THE CALLER ID MEMORY
If you have new calls (‘NEW’ icon and New Call LED is lit). Press
[ ] or [ ] to read all of the most recent calls. The CALL# will
decrease.
Once all the new calls have been read, ‘END OF NEW CALL’
will be displayed.
Press [ ] to view the oldest calls, or press [ ] to view the most
recent calls.
NOTE: After you view all the call in memory, the LCD will show
‘END OF LIST’.
NOTES:
1. The New Call LED will blink until all the new Caller ID data
has been reviewed.
2. If the ‘RPT’ icon is turned on, you have received multiple NEW
calls from the same number.
3. If you receive a call from a number stored in (previously
reviewed) memory, the data in memory will be replaced with
the new call’s time and date and the ‘NEW’ icon will be turned
on.
If no key is pressed within 20 seconds, the LCD will show the
‘Answer-Ready’ mode, and display the total call counter, new
call counter, current time and date.
ERASE THE CALLER ID MEMORY
Press [ ] or [ ] for the Caller ID memory location to be reviewed.
To clear a single Caller ID memory location, press [ERASE]
twice quickly.
The data for that call will be erased, and the CALL# and Caller
ID information will be updated.
After all new message being reviewed, press and hold [ERASE]
for 3 seconds. The message ‘ERASE ALL CALLS?’ will appear
to confirm your action. Press [ERASE] to clear all the information,
then the message ‘NO CALLS’ appear.
Both the total call and new call counters will become zero, and
the current time and date will be displayed.
NOTE: All new calls must be reviewed before clearing the entire
memory.
CALL BACK (REDIAL) FROM THE
CALLER ID MEMORY
With the handset hung up on the base press [ ] or [ ] to find the
Caller ID memory location to be redialed.
Press [CALL BACK] twice to redial, the LCD shows ‘LIFT
HANDSET’ or ‘PICK UP CALL’.
Pick up the handset to make your phone call.
With the handset off hook, press [ ] or [ ] to find the Caller ID
memory location to be redialed. Press [CALL BACK] twice, the
number will then be dialed automatically.
WHEN THE CALLER’S PHONE
NUMBER HAS A DIFFERENT AREA
CODE FROM THE PRESET:
The long distance dialing digit ‘1’ will be inserted automatically
during Caller ID memory call back.
Press [CALL BACK], 11 digits number will blink. Press [CALL
BACK] again to confirm to dial the 11 digits number.
10
11
WHEN THE CALLER’S PHONE
NUMBER HAS THE SAME AREA CODE
AS THE PRESET:
The long distance dialing digit ‘1’ and the 3 digits area code will
be deleted automatically during Caller ID memory call back.
Press [CALL BACK], 7 digits number will blink. Press [CALL
BACK] again to confirm to dial the 7 digits number.
NOTE: Your telephone company may require a different format
for making out-of-area (toll) calls WITHIN your area code. See
the next section for the procedure to obtain the applicable tollcall format for your phone company.
WHEN YOUR TELEPHONE COMPANY REQUIRES YOU TO
DIAL OTHER THAN A 7-DIGIT NUMBER (SAME AREA
CODE) OR 11-DIGIT NUMBER (DIFFERENT AREA CODE)
TO MAKE TOLL CALLS WITHIN YOUR AREA CODE,
FOLLOW ONE OF THE 4 OPTIONS BELOW FOR CALLER
ID CALL BACK.
Option 1
1+Area Code+7-Digit Number (11 digits)
Option 2
1+7-Digit Number (8 digits)
Option 3
Area Code+7-Digit Number (10 digits)
Option 4
7-Digit Number Only.
Follow the procedure below to select one of the above
options for Caller ID call back.
With the handset hung up on the base.
1 Press [ ] or [ ] to find the Caller ID memory location to redial.
Press [CALL BACK], the 7-digit number (if same area code)
or 11-digit number (if different area code) will blink.
2. Press [ ] or [ ] to select one of the options.
3. Press [CALL BACK] again to confirm the dial.
12
LOW BATTERY INDICATION
The CID110 will signal you when the batteries become weak
and need replacement. Once battery power has been sufficiently
drained, the CID110 will appear the BATTERY LOW icon ( )on
the LCD display. Replace the AA batteries with three (3) fresh
ones in order to maintain the Caller ID and Speed Dialing
memories. If you do not install fresh batteries within 2 minutes,
your Caller ID and telephone memory information may be lost.
CUSTOMER INFORMATION
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the bottom of this
equipment is a label that contains, among other information, a
product identifier of US: DJTMT10BCID110. If requested, this
number must be provided to the telephone company.
The applicable jacks ( i.e. RJ11C ) for this equipment are provided
in the packaging with each piece of approved equipment. The
jacks are certified by Universal Service Order Codes (USOC).
A plug and jack used to connect this equipment to the premises
wiring and telephone network must comply with the applicable
FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug are provided with
this product. They are designed to be connected to a compatible
modular jack that is also compliant. See installation instructions
for details.
The REN is used to determine the number of devices that may
be connected to a telephone line. Excessive RENs on a
telephone line may result in the devices not ringing in response
to an incoming call. In most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by the
total RENs, contact the local telephone company.
13
If this equipment CID110 causes harm to the telephone network,
the telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice
isn’t practical, the telephone company will notify the customer
as soon as possible. Also, you will be advised of your right to file
a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities,
equipment, operations or procedures that could affect the
operation of the equipment. If this happens the telephone
company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
If you experience trouble with this equipment, disconnect it from
the network until the problem has been corrected or until you
are sure that the equipment is not malfunctioning.
Please follow instructions for repairing if any (e.g. battery
replacement section); otherwise do not alter or repair any parts
of device except specified.
Connection to party line service is subject to state tariffs. Contact
the state public utility commission, public service commission
or corporation commission for information.
This equipment is hearing aid compatible.
NOTICE: If your home has specially wired alarm equipment
connected to the telephone line, ensure the installation of this
(equipment ID if any) does not disable your alarm equipment. If
you have questions about what will disable alarm equipment,
consult your telephone company or a qualified installer.
WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
14
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. Some cordless telephones operate at frequencies
that may cause interference to nearby TV’s and VCR’s; to
minimize or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a TV or VCR;
and, if interference is experienced, moving the cordless
telephone farther away from the TV or VCR will often reduce or
eliminate the interference. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for
help.
ADDITIONAL INFORMATION
A. When your CONAIRPHONETM is not in use make sure the
handset is engaged into the base unit.
B. Avoid rough handling, areas with excessive moisture heavy
dust or extreme temperature.
C. To clean, use mild detergent and slightly damp cloth, never
use strong solvents or abrasives.
D. Connecting this telephone to a coin operated telephone or a
party line is prohibited by law.
E. If it is determined that your telephone is malfunctioning, the
FCC requires that it be disconnected from the modular outlet
until the problem has been corrected.
15
SERVICE
According to FCC regulations, this equipment, which has been
certified and registered by the FCC, may only be repaired by
authorized persons. If repairs or adjustments are made by an
unauthorized person, the FCC certification may be voided.
Should you encounter any problems, please call the
ConairphoneTM toll-free Customer Hotline for assistance:
1-800-366-0937, Monday - Friday
between the hours of 8:30 am - 9:00 pm and
Saturday 8:30 am - 12:30 pm (EST).
You can also visit our website at
www.conairphone.com
FOR IN-WARRANTY SERVICE:
Package your complete unit (including all adapters, line cords,
and other accessories) and ship the unit postage prepaid* and
insured (for your protection) to:
CONAIRPHONETM
DEPT.: In Warranty Repair
7475 North Glen Harbor Blvd., Glendale, AZ 85307
Be sure to include your return address, proof of purchase, a
daytime phone number, $5.00 for postage and handling*, and a
brief explanation of your difficulties.
*NOTE: California residents need only provide proof of purchase
and should call 1-800-366-0937 for shipping instructions.
FOR OUT-OF-WARRANTY SERVICE:
You may call our toll-free Help Line for the price of a replacement
before returning your unit. Please follow all instructions for InWarranty service (above) to return your unit, and mark the
package: DEPT.: Out-of-Warranty.
If you have called and know the cost of your replacement, please
include this information with your unit for prompt service.
16
QUESTIONS?
STOP ... don’t take unit back to the store.
LOOK ... for the toll-free “help” telephone number.
LISTEN ... as our experts talk you through the problem.
For immediate answers to your questions regarding operation,
missing parts or installation, call:
CONAIRPHONETM
HOTLINE AT:
1-800-366-0937
LIMITED WARRANTY
This ConairphoneTM is warranted to the original purchaser to be
free from defects in materials and workmanship under normal
installation, use, and service for a period of one (1) year from
the date of purchase as shown on the purchaser’s receipt.
The obligation of ConairphoneTM Retail Sales under this warranty
shall be limited to repair or replacement (at our option) during
the warranty period of any part which proves defective in material
or workmanship under normal installation, use, and service,
provided the product is returned to ConairphoneTM or to one of
our authorized Service Centres TRANSPORTATION CHARGES
PREPAID. Products returned to us or to an Authorized Service
Center must be accompanied by a copy of the purchase receipt.
In the absence of such purchase receipt, the warranty period
shall be one (1) year from the date of manufacture. To obtain
service under this warranty, return the defective product to the
service center nearest you together with your sales slip and
$5.00 for postage and handling. (California residents need only
provide proof of purchase). You may also have other warranty
rights which vary from state to state.
This warranty shall be invalid if the product is damaged as a
result of defacement, misuse, abuse, neglect, accident,
destruction or alteration of the serial number, improper electrical
voltages or currents, repair alteration or maintenance by any
person or party other than our own service facility or an
authorized Service Center, or any use violative of instructions
furnished by us.
17
This warranty is also rendered invalid if this product is removed
from the country in which it was purchased, if it is used in a
country in which it is not registered for use, and/or if it is used in
a country for which it was not designed. Due to variations in
telephone systems and communications laws, this product may
be illegal for use in some countries. ConairphoneTM assumes
no responsibility for damages or penalties incurred resulting from
the use of this product in a manner or location other than that
for which it is intended.
This one-year limited warranty is in lieu of all other expressed
warranties, obligations, or liabilities.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR
LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, SHALL BE LIMITED IN
DURATION TO THE ONE-YEAR DURATION OF THIS
WRITTEN LIMITED WARRANTY. SOME STATES DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT
APPLY TO YOU.
IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR
BREACH OF THIS OR ANY OTHER WARRANTY,
EXPRESSED OR IMPLIED, WHATSOEVER.
Some states do not allow the exclusion or limitation of special,
incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which may vary
from state to state.
18
Download PDF

advertising