Contec PPC-HDD(MS)A Computer Drive User Manual

2
CheckMate™ IV
Model RT-U49H+
Universal Remote
Control
1. Introduction
Your CheckMate IV, Model RT-U49H+, universal
remote control is simple to program, easy to use,
and can operate up to four (4) devices, which
include:
CABLE
TV
VIDEO
AUDIO
Cable set-top terminals
Televisions
VCR, DVD players
Audio-video receivers, amplifiers, CD
players, cassette players, DMX / DCR
Digital Music converters
Before you can use your remote control, it must be
programmed (set-up) to operate the above devices.
3
Reset
Lets you reset your remote to its original default
settings. For more information, see section 17.
3. Installing / Replacing Batteries
Install two (2) “AAA” batteries as indicated by the
diagram in the battery compartment.
When the illuminated buttons become dim or do not
illuminate during use, install two (2) new “AAA” size
batteries.
Your remote control has Memory GuardTM, which
eliminates reprogramming after battery changes.
4. Programming Your Cable Set-Top Terminal
2. Before Getting Started
Some of the special features on your remote control
are:
Point and PressTM Programming
Lets you program your TV, VIDEO and AUDIO
devices without using codes. For more information,
see sections 5, 6, 7and 8.
SmartKeys™
Program multiple button presses on the [CABLE],
[TV], [BYPASS] and [PPV] buttons. For more
information, see section 14.
[DEVICE] Button
Tells which device you are currently operating by
illuminating the device's power button. While the
current device is illuminated, press a nonilluminated power button to operate a different
device.
[VCR / VOD] Button
"Toggles" the VCR buttons between cable "VideoOn-Demand" (VOD) and VCR / DVD functions.
Programming & Operating
Instructions
To have a clearer idea of the features and
capabilities of your remote control, take a moment
to carefully read these instructions
Save for future reference.
Rev. 9/2001
© 2001, CONTEC CORPORATION
Memory GuardTM
Eliminates reprogramming after battery changes.
Time Out
Shuts remote off if any button is pressed and held
for 45 seconds. This extends battery life in the
event the remote becomes lodged under or
between heavy objects.
Your remote control is pre-programmed to
operate Motorola's DCT® (digital) and CFT2200
(analog) set-top terminals. If you are operating
either of these cable set-top terminals, no cable
programming is necessary - proceed to section 5.
If you need to operate another cable set-top
terminal, look up the brand and model number in the
Cable Setup Code list. If you are not sure of your
brand and model, contact your cable company.
To program (setup) your cable set-top terminal...
1. Turn on your cable set-top terminal.
2. Press [DEVICE], then [MUTE] together - hold
both buttons down until the lighted mode buttons
start blinking in sequence.
3. Press [CABLE]. The [CABLE] button lights up.
4. From the Cable Setup Code list, locate and enter
the 3-digit code for your brand and model.
5. Press [CABLE] to lock in the code. The [CABLE]
button will blink and go out.
Cable brand & setup code __________________
5. Programming Your TV
If you have a TV that's operated by remote control,
it's recommended that you plug it directly into a wall
outlet instead of the cable set-top terminal.
4
To program (setup) your TV...
1. Turn on your TV.
2. Press [DEVICE], then [MUTE] together - hold
both buttons down until the lighted mode buttons
start blinking in sequence.
3. Press [TV]. The [TV] button lights up.
5
DVD player turns off. If multiple codes are listed,
you may have to enter several 3-digit codes until
your VCR / DVD turns off.
5. Press [ MUTE ]. If your VCR or DVD player
turns back on, press [VIDEO] to lock in the
code. The [VIDEO] button will blink and go out.
If your VCR or DVD doesn't turn back on,
repeat steps 4 and 5 above until you can turn
your VCR or DVD off and on.
4. a. Press and hold [CH ] until your TV turns off.
As soon as your TV turns off, release [CH ]❶.
OR
4. b. From the TV Setup Code list, locate and enter
the 3-digit code until your TV turns off. If multiple
codes are listed, you may have to enter several
3-digit codes until your TV turns off.
5. Press [MUTE]. If your TV turns back on, press [TV]
to lock in the code. The [TV] button will blink and
go out.
If your TV doesn't turn back on, repeat steps 4 and
5 above until you can turn your TV off and on.
TV brand & setup code ______________________
❶
NOTE when using the Point and Press™
Programming method (step 4a.). If you find a code
that turns your TV off but not back on, you may have
gone past the correct matching code. Try pressing
[CH ] one step at a time until you find a code that
turns your TV back on.
4. b. From the VCR or DVD Setup Code list, locate
and enter the 3-digit code until your VCR or
2. Press [DEVICE], then [MUTE] together - hold
both buttons down until the lighted mode buttons
start blinking in sequence.
4. a. Press and hold [CH ] until your Audio device
turns off. As soon as your Audio device turns
off, release [CH ]❶ .
NOTE when using the Point and Press™
Programming method (step 4a.). If you find a
code that turns your VCR or DVD off but not back
on, you may have gone past the correct matching
code. Try pressing [CH ] one step at a time until
find a code that turns your VCR or DVD back on.
7. Programming Your TV / VCR Combination
1. First, program your remote for the TV
functions.
OR
4. b. From the Audio Setup Code list below, locate
and enter the 3-digit code until your device
turns off. If multiple codes are listed, you may
have to enter several 3-digit codes until your
Audio device turns off.
4. a. Refer to Section 5 - Programming Your TV.
5. Press [MUTE]. If your Audio device turns back on,
press [AUDIO] to lock in the code. The [AUDIO]
button will blink and go out.
4. b. Find a TV Setup Code that operates the TV
functions (power, vol / , mute, CH / ,
0-9) of your TV / VCR unit.
If your Audio device doesn't turn back on, repeat
steps 4 and 5 above until you can turn your Audio
device off and on.
To program (setup) your VCR or DVD player...
OR
1. Turn on your Audio device.
❶
4. a. Refer to Section 6 - Programming Your VCR
or DVD.
3. Press [VIDEO]. The [VIDEO] button lights up.
4. a. Press and hold [CH ] until your VCR or DVD
turns off. As soon as your VCR or DVD turns
off, release [CH ]❶.
To program (setup) your audio-video receiver,
amplifier, CD player, cassette player or Digital
Music converter...
3. Press [AUDIO]. The [AUDIO] button lights up.
6. Programming Your VCR or DVD
2. Press [DEVICE], then [MUTE] together - hold
both buttons down until the lighted mode buttons
start blinking in sequence.
8. Programming Your Audio Device
VCR / DVD brand & setup code ____________
2. Then, program your remote for the VCR
functions.
1. Turn on your VCR or DVD player.
6
Audio brand & setup code ___________________
❶
4. b. Enter, lock and test each 3-digit VCR Setup
Code until a code is found that operates the
VCR functions (play, stop, fast-forward,
rewind, pause, record) of your TV / VCR
unit.
NOTE when using the Point and Press™
Programming method (step 4a.). If you find a code
that turns your Audio device off but not back on, you
may have gone past the correct matching code. Try
pressing [CH ] one-step at a time until find a code
that turns your Audio device back on.
NOTE: You can not use the Point and Press™
Programming method to program the VCR
functions of your TV / VCR unit.
9. Operating Your Cable Set-Top Terminal
Your remote control is designed to operate all the
features and functions of your cable set-top
terminal.
7
To select your remote's CABLE mode and
operate your cable set-top terminal, press
[DEVICE] then [CABLE]. The [CABLE] button will
blink and go out. Then press...
[CABLE]
[TV]
[VIDEO]
[AUDIO]
[CH ] / [CH ]
[VOL ] / [VOL
[MUTE]
[EXIT]
[MENU]
[GUIDE]
CABLE on / off.
TV on / off.
VCR / DVD on / off.
AUDIO device on / off.
Increases / decreases CABLE channel.
] Increases / decreases TV volume.
Mutes TV volume.
Exits on-screen menus, view guide.
Displays on-screen features, options.
Displays on-screen listing of programs
by date, time, channel.
[INFO]
Displays channel, time information.
[PPV] / [LOCK] Displays pay-per-view events, enter
parental control access code
[PG ] / [PG ] Page up / down through menus, view guide.
[DAY ] / [DAY ] Previous / next day in view guide
[ ], [ ], [ ], [ ]Navigate on-screen menus, program
guide, PPV events and interactive
services.
[OK] / [SEL]
Select menu option, program PPV
events and function options.
[MUSIC] / [ENT] Selects Music Choice™ digital music
through your cable set-top terminal
[HELP]
Displays on-screen help on cable settop terminals so equipped.
[FAV]
Scroll through favorite channels
[LAST]
Displays last channel viewed.
[A], [B], [C]
Functions set by cable operator.
[0] - [9]
Numeric entry buttons.
[BYPASS]
RF bypass on cable set-top
terminal.
[VCR / VOD]
Toggles VCR buttons between cable
"Video -On-Demand" (VOD) and
VCR functions.
[HELP] + [LAST] Cable set-top terminal diagnostic
functions (DCT, CFT2200)
In your remote's CABLE mode, you can also
press the blue buttons at the bottom to operate
your VCR / DVD's basic functions or the "VideoOn-demand" (VOD) functions on your cable settop...
8
[
[
[
[
[
[
]
]
]
]
]
]
VOD or VCR / DVD rewind.
VOD or VCR / DVD play.
VOD or VCR / DVD fast-forward.
VOD or VCR / DVD pause.
VOD or VCR / DVD stop.
VOD or VCR record.
10. Operating Your TV
Your remote control can operate many functions of
your TV.
To select your remote's TV mode and operate
your TV, press [DEVICE] then [TV]. The [TV]
button will blink and go out. Then press...
[TV]
TV on / off.
[CABLE]
CABLE on / off.
[VIDEO]
VCR / DVD on / off.
[AUDIO]
AUDIO on / off.
[CH ] / [CH ] Increases / decreases TV channels.
[VOL ] / [VOL ] Increases / decreases TV volume.
[MUTE]
Mutes TV volume.
[0] - [9]
Numeric entry buttons.
[MENU] or [OK/SEL] Accesses TV's on-screen menus.
[BYPASS] / [TV/VCR] Change TV's video inputs.
[LAST]
View last TV channel
[INFO]
Displays TV channels and time.
[EXIT]
Exits TV's on-screen menus
[PIP]
Picture-in-picture on / off.
[POS]
Picture-in-picture position.
[SWAP]
Picture-in-picture swap.
[FRZ]
Picture-in-picture freeze.
[ ], [ ], [ ], [ ] Navigates TV's menu.
[MUSIC] / [ENT] Pressed after 0-9 to change channels
on some TV's
[C]
Sleep / timer functions.
In your remote's TV mode, you can also press
the blue buttons at the bottom to operate your
VCR / DVD's basic functions...
[
[
[
[
[
[
]
]
]
]
]
]
VCR / DVD rewind.
VCR / DVD play.
VCR / DVD fast-forward.
VCR / DVD pause.
VCR / DVD stop.
VCR record.
9
11. Operating Your VCR or DVD
Your remote control can operate many functions of
your VCR or DVD player.
To select your remote's VIDEO mode and
operate your VCR or DVD, press [DEVICE] then
[VIDEO]. The [VIDEO] button will blink and go
out. Then press...
[VIDEO]
[CABLE]
[TV]
[AUDIO]
[CH ] / [CH ]
VCR / DVD power on / off.
CABLE on / off.
TV on / off.
AUDIO on / off.
Increases / decreases VCR channels,
or DVD skip "+ / –".
[VOL ] / [VOL ] Increases / decreases TV volume.
[MUTE]
Mutes TV volume.
[0] - [9]
Enter VCR channels.
[BYPASS] / [TV/VCR] Change VCR's video inputs.
[EXIT]
DVD clear functions.
[MENU]
DVD menu functions.
[GUIDE]
DVD guide functions.
[INFO]
DVD program information.
[ ], [ ], [ ], [ ] Navigate DVD menu.
[MUSIC] / [ENT] DVD enter functions.
[A]
DVD subtitle on / off.
[LAST]
DVD return function.
In your remote's VIDEO mode, you can also
press the blue buttons at the bottom to operate
your VCR / DVD's basic functions...
[
[
[
[
[
[
]
]
]
]
]
]
VCR / DVD rewind.
VCR / DVD play.
VCR / DVD fast-forward.
VCR / DVD pause.
VCR / DVD stop.
VCR record.
10
To select your remote's AUDIO mode and
operate your Audio devices, press [DEVICE]
then [AUDIO]. The [AUDIO] button will blink and
go out. Then press...
For audio-video receivers, press...
[AUDIO]
A/V receiver on / off.
[VOL ] / [VOL ] Increases / decreases Audio volume.
[MUTE]
Mutes Audio volume.
[CH ] / [CH ] Next / last preset tuner channel.
[1]
Select "Tuner" input.
[2]
Select "CD" input.
[3]
Select "Tape # 1" input.
[4]
Select "Tape # 2" input.
[5]
Select "Phone" input.
[6]
Select "VCR # 1" input.
[7]
Select "VCR #2" input.
[8]
Select "LD" input.
[9]
Select "AUX" input.
[0]
Select "TV" input.
[BYPASS] / [TV/VCR] AM / FM on tuner.
For CD and cassette players, press...
CD / cassette rewind.
[ ]
CD / cassette play.
[ ]
CD / cassette fast-forward.
[ ]
CD / cassette pause.
[ ]
CD / cassette stop.
[ ]
Cassette record.
[ ]
The volume control options in each mode of the
remote are:
CABLE
TV
VIDEO
AUDIO
TV (default), Cable or Audio.
TV (default), Cable or Audio.
TV (default), Cable or Audio.
Audio device (default), Cable or TV.
To control volume / mute through your cable
set-top terminal in the remote's cable mode...
1. Press [DEVICE], then [MUTE] together - hold
both down until the lighted mode buttons start
blinking in sequence.
2. Press [CABLE] to select the cable mode. The
[CABLE] button lights up.
3. Press [VOL ], then [CABLE] for cable volume.
The [CABLE] button will blink and go out.
To return volume control back to your TV, repeat
steps 1. and 2. above, then press [VOL ], then [TV]
in step 3.
14. Your Remote's SmartKeys™
Your remote has four (4) SmartKeys™ [ CABLE ], [ TV ], [ PPV ], and [ BYPASS ] that
operate in its cable mode. Each SmartKey™ can
be programmed so whenever it's pressed, it can
transmit up to 12 individual button presses in
sequence.
For DCR and DMX Digital Music Converters,
press...
Programming and using the [CABLE] SmartKey™
[AUDIO]
DCR / DMX on / off.
[VOL ] / [VOL ] Increases / decreases volume.
[MUTE]
Mutes volume.
[CH ] / [CH ] Change music selections.
[0] - [9]
Enter selections directly.
The [CABLE] button normally turns on / off your
cable set-top terminal. Here's an example of how to
program the [CABLE] SmartKey™ to turn on (or off)
your cable set-top terminal and TV, then tune your
TV to its correct output channel, typically 3, with one
button press...
12. Operating Your Audio Device
13. Programming Volume Control
Your remote control can operate many functions of
your audio-video receiver, amplifier, CD player,
cassette player or DMX / DCR Digital Music
converter.
11
When you first program your remote, volume / mute
are controlled through your TV (except AUDIO
volume which defaults to the AUDIO device).
1. Press [DEVICE], then [CABLE] to select the
Cable mode of your remote.
2. Press [CABLE], then [SEL / OK] together - hold
both down together until the [CABLE] button lights
up.
12
3. In this order, press [TV], [0], [3]. The [CABLE]
button will blink and remain illuminated.
4. Press [CH ] to lock in this setting. The [CABLE]
button will blink and go out.
To return the [CABLE] button to its normal default
setting, repeat steps 1 and 2 above, then press
[CH ].
Programming and using the [TV] SmartKey™
The [TV] button normally turns on / off your TV.
Here's an example of how to program the [TV]
SmartKey™ to turn on (or off) your TV, then tune
your TV to its correct output channel, typically 3, with
one button press...
1. Press [DEVICE], then [CABLE] to select the
Cable mode of your remote.
2. Press [TV], then [SEL / OK] together - hold
both down together until the [TV] button lights
up.
3. In this order, press [0], [3]. The [TV] button will
blink and remain illuminated.
4. Press [CH ] to lock in this setting. The [TV]
button will blink and go out.
To return the [TV] button to its normal default
setting, repeat steps 1 and 2 above, then press
[CH ].
Programming and using the [PPV] SmartKey™
The [PPV] button (Cable mode) normally displays
your cable system's listing of pay-per-view events.
Here's an example of how to program the [PPV]
SmartKey™ to tune to a specific cable channel
(123) with one button press...
1. Press [DEVICE], then [CABLE] to select the
Cable mode of your remote.
2. Press [PPV], then [SELECT / OK] together - hold
both down together until the [CABLE] button lights
up.
3. In this order, press [1], [2], [3]. The [CABLE]
button will blink and remain illuminated.
4. Press [CH ] to lock in this setting. The [CABLE]
button will blink and go out.
13
To return the [PPV] button to its normal default
setting, repeat steps 1 and 2 above, then press
[CH ].
Programming and using the [BYPASS] SmartKey™
The [ BYPASS ] button (Cable mode) normally
transmits a command that puts your cable set-top
terminal in a BYPASS mode. While the cable set-top
terminal is in its BYPASS mode, you can record one
program on your VCR while watching a different
program through your TV. When exiting cable settop terminal's BYPASS mode, your TV must be retuned to its correct output channel, typically 3, for
proper cable reception.
Here's an example of how to program the [BYPASS]
SmartKey™ so whenever it is pressed, it will also
tune your TV to its correct output channel, typically
3, for proper cable reception...
1. Press [DEVICE], then [CABLE] to select the
Cable mode of your remote.
2. Press [BYPASS], then [SELECT / OK] together hold both down together until the [CABLE] button
lights up.
3. In this order, press [DEVICE], [TV], [0], [3]. The
[CABLE] button will blink and remain illuminated.
4. Press [CH ] to lock in this setting. The [CABLE]
button will blink and go out.
To return the [BYPASS] button to its normal default
setting, repeat steps 1 and 2 above, then press
[CH ].
Remember: When using any SmartKey™ to
transmit a series of functions, be sure to keep your
remote aimed at the devices to ensure all functions
are received in their entirety.
15. Programming a 2 nd TV, VCR, DVD
Instead of programming an audio device, you can
program your remote to operate a 2nd TV, 2nd VCR,
or 2nd DVD player.
To program a 2nd TV to your remote's [AUDIO]
button...
14
1. Turn on your 2nd TV.
2. Press [DEVICE], then [MUTE] together - hold
both buttons down until the lighted mode buttons
start blinking in sequence.
3. Press [AUDIO], then [TV]. The [AUDIO] and [TV]
buttons will start blinking.
4. a. Press and hold [CH ] until your 2nd TV turns off.
As soon as your 2 nd TV turns off, release
[CH ]❶.
OR
4. b. From the TV Setup Code list, locate and enter
the 3-digit code until your 2nd TV turns off. If
multiple codes are listed, you may have to
enter several 3-digit codes until your 2nd TV
turns off.
5. Press [MUTE]. If your 2nd TV turns back on, press
[AUDIO] to lock in the code. The [AUDIO] button
will blink and go out.
If your 2nd TV doesn't turn back on, repeat steps 4
and 5 above until you can turn your 2nd TV off and
on.
❶ NOTE when using the Point and Press™
Programming method (step 4a.). If you find a code
that turns your 2nd TV off but not back on, you may
have gone past the correct matching code. Try
pressing [CH ] one step at a time until find a code
that turns your 2nd TV back on.
If you want to program a 2 VCR or DVD player in
the above example, you would press [AUDIO], then
[VIDEO] in step 3., then steps 4. and 5. referring to
the Video Setup Code list.
nd
16. Code Number Read Back
To identify a 3-digit device code stored under the
Point and Press™ method, follow these steps:
1. Press [DEVICE], then [MUTE] - hold both down
until the illuminated mode buttons start blinking in
sequence.
2. Press [CABLE] to identify your cable set-top
terminal code. Or [TV], [VIDEO], [AUDIO] to
identify these codes. The selected mode button
will be illuminated.
15
3. Press [INFO]. The illuminated button "blink back"
the code numbers, with a 1 second interval
between each digit of the code.
Example: For code "035", the remote will blink 10
times, then 3 times, then 5 times.
17. Resetting Your Remote Control
To reset you remote to its factory default settings...
1. Press [SELECT / OK], then [LAST] - hold both
down together until the [CBL], [TV], [VIDEO], and
[AUDIO] buttons blink in sequence two times
(approx. 5 seconds).
18. Helpful Tips & Troubleshooting
1. Your remote is equipped with a Point and Press™
quick-programming sticker on the back of its case.
This will help you quickly program the remote
without using codes.
2. The illuminated mode button will remain on while
the remote is in a programming mode. In the
absence of an entry, the button will go out after 20
seconds.
When locking in your devices, the illuminated
mode button will blink and go out.
3. When using the Point and Press™ programming
method, you may find a code that turns your
device off but not back on. If this happens...
3. a. the correct code has not been found. Continue
pressing [CH ] until your devices turn on and
off.
3. b. you may have gone past the correct matching
code. Try pressing [CH ] one step at a time
until find a code that turns your cable set-top
terminal back on.
4. NOTE: If you have a Scientific Atlanta 8500 series
cable set-top terminal, press [CH ] or [CH ] to
turn on the cable set-top terminal. Press [CABLE]
to turn these cable set-top terminals off.
5. When operating a General Instrument model
DPBB Cable set-top terminal (Cable Setup Code
#101), your remote's transmitting distance is
limited to 20 ft. This is due to receiving limitations
of the cable set-top terminal.
16
6. If you have any questions concerning the operation
of your cable set-top terminal, contact your cable
operator.
Cable Setup Codes
Manufacturer
MOTOROLA (GI)
Model
Code
DCT, CFT2200
001
CFT2000, CFT2100, WNR
115
JERROLD
DL4, DP(V), DQN(V), DPBB
101
OAK / TOCOM
SIGMAONE P1, P2& P3,
037
SIGMA2000, SIGMA 550
PIONEER
VOYAGER
122
BC4100, 4200, 4500, 4600
034
BA5000, 6000
BA-V1000, BA-V2000
120
BA-9000
121
PACE
510 Digital
122
PHILIPS
Digital
017
SCIENTIFIC-ATLANTA EXPLORER
122
8600X
002
8600
011
8540, 8550, 8570, 8580, 8590 042
TOCOM
5503VIP & 5507, 5508
003
ZENITH
MM2500
008
Z-TAC
108
TV Setup Codes
Admiral
Akai
Amark
Ampro
Amstrad
Anam
AOC
Audiovox
Blaupunkt
Cairn
Candel
Capehart
Cetronic
Citizen
Classic
Concerto
Contec
072 081 161 160
001 146
112 143
073 167 157
052
043 056 080 112 131
001 004 058 112
076
088
201
001 002 003 004
058
043
001 002 003 004 043 101 103 143
043
004
043 050 051
17
Coronado
Craig
Crown
Curtis Mathes
CXC
Daewoo
Daytron
Dwin
Dynasty
Dynatech
Eiki
Electrohome
Emerson
Fisher
Fujitsu
Funai
Futuretech
GE
Goldstar
Hall Mark
Hitachi
Infinity
JBL
JC Penny
Jensen
JVC
KEC
Kenwood
Kloss
KMC
KTV
Lodgenet
Logik
Luxman
LXI
Magnavox
Marantz
Matsui
Memorex
143
043
043 143
001 004 101 143
043
004 016 043 044 076 103 114 125
127 143
004 143
177
043
062
187
024 076 143 196
001 004 005 028 043 047 048
050 051 076 096 143 151 153
154 155
007 057
198
028 043
043
001 004 008 009 034 056 073
074 091 130 144 155 157 160
161 165
004 102 106 112 113 116 119
127 143
004
004 009 010 011 012 023 072
075 143 158 163 166
164
164
001 004 008 009 024 030 065
101 143 156 160
013
034 038 070 083 145 199
043
001 070
002 059
143
001 043 143 154
072
072
044
007 015 052 081 160 164 166
001 003 004 022 059 060 061
063 064 094 127 160 164
001 164
164
004 007 072
18
Metz
MGA
Minerva
Mitsubishi
MTC
NAD
NEC
Nikei
Onking
Onwa
Optonica
Orion
Panasonic
Philco
Philips
Pioneer
Portland
Proscan
Proton
Quasar
Radio Shack
RCA
Realistic
Roctec
Runco
Sampo
Samsung
Sanyo
Scott
Sears
Seleco
Sharp
Siemens
Signature
Sony
Soundesign
Spectricon
SSS
Supre Macy
088
001 004 024 028 042
088
004 024 028 040 042 109 124
146 191
001 004 062 101
015 025
001 016 019 024 040 056 130
132 134
043
043
043
019 081
096
034 056 080 092 164
001 003 004 024 056 059 060
063 064 164
001 003 004 005 038 059 093
127 164
001 018 023 025 116 135 190
004 143
144 160 161 165 167
004 058 131 143 171 173 193
034 056 092
004 019 043 127 143
001 004 023 024 056 065 074
144 152 156 160 161 165
007 019 043 047
186
073 157 168 169 178 179 180
181 182
001 004 058 202
004 050 089 101 105 127 143
160
007 020 053 057 082 166 187
004 028 043 048 143
004 007 015 028 030 057 082
094 143 160 165 166
189 200
004 014 019 022 028 029 081
143 170 175
088
072
070 085 126 139 147 185 194
003 004 028 043
112
004 043
002
19
Sylvania
001 003 044 059 060 063 064
127 160 164
Tandy
081
Tatung
056 062
Technics
034 080
Techwood
004
Teknika
002 003 004 024 028 043 072
101 143
Telefunken
037 046 086 087
Telerent
072
Tera
172
TMK
004
Toshiba
007 015 030 040 062 101 138
Totevision
143
Universal
008 009
Video Concepts 146
Vidikron
174 184 188 192
Vidtech
004
Wards
004 008 009 019 028 034 060
061 063 064 072 074 143 164
Westing House 076
Yamaha
001 004
York
004
Yupiteru
043
Zenith
072 073 095 103 157
Zonda
112
VCR Setup Codes
Aiwa
Akai
Ampro
Anam
Audio Dynamics
Brocksonic
Canon
Capehart
Craig
Curtis Mathes
Daewoo
Daytron
DBX
Dynatech
Electrohome
Emerson
034 161
016 043 046 124 125 142 146
072
083
012 023 039 043
035 037 129
028 083
108
001 104 135
041 083
005 007 010 065 108 110 111
112 117
108
012 023 039 043
034 053
059
006 025 027 029 034 035 036
037 046 083 106 117 129 131
138 153 162
20
Fisher
Funai
GE
Go Video
Goldstar
Harman/Kardon
Hitachi
Instantreplay
JCL
JC Penny
Jensen
JVC
Kenwood
Lloyd
LXI
Magin
Magnavox
Marnatz
Marta
Matsui
MEI
Memorex
MGA
Minolta
Mitsubishi
MTC
Multitech
NEC
Nordmende
Optonica
Orion
Panasonic
Pentax
Philco
Philips
Pilot
Pioneer
Portland
Pulsar
Quartz
Quasar
Radio Shack
RCA
001 008 009 010
034
063 072 083 107 109 144 147
104 115 132 136 155
012 020 106 114 123
012 045
018 020 026 034 043 063 150
160
083
083
012 020 083 104 106
043
012 043 048 050 055 060 083
130 150 152
014 034 047 048
034
001 009 034 106
104
034 041 067 068 083 156 164
012 067 069 083
106
027 030
083
001 010 014 034 053 072 083
104 106 134 139
045 046 059
020
020 045 046 049 051 059 061
142 151
034 104
024 034
012 023 039 043 048
043
053 054
025
070 074 083 133 140 145
020 063 083
034 067 083
034 054 067 071 083 106
106
020 021 048
108
072
002 041
075 083 145
123
020 034 041 104 107 109 140
144 145 147 158
21
Realistic
001 008 010 014 034 053 054
083 104 106
Rico
058
Runco
148
Salora
014
Samsung
032 083 104 107 109 112 113
115 122 125
Sansui
043 048 135
Sanyo
001 007 010 014 104 134
Scott
037 112 129 131
Sears
001 008 009 010 014 020 073
081 106 112
Sharp
053 054 083 159 165
Shintom
024
Signature
034
Sony
001 052 053 056 057 058 076
078 083 154
Soundesign
034
STS
020
Sylvania
034 059 067 083
Symphonic
034
Tandy
010 034
Tatung
039 043
Teac
034 039 043
Technics
070 083
Teknika
019 034 083 106
Thomas
034
TMK
006
Toshiba
008 020 042 047 059 079 081
082 112 131
Totevision
104 106
Unitech
104
Vector Research 012
Victor
048
Video Concepts 012 034 046 141
Videosonic
104
Wards
001 020 024 034 053 054 083
104 131
Yamaha
012 034 039 043
Zenith
034 048 056 058 072 080 106
DVD Setup Codes
Apex Digital
Denon
GE
Harman/Kardon
220
226 240
231 243
218 225
22
JVC
KLH
Kenwood
LG
Magnavox
Marantz
Mitsubishi
NAD
Onkyo
Panasonic
Philips
Pioneer
Proceed
Proscan
RCA
Samsung
Sharp
Sony
Thomson
Toshiba
Yamaha
Zenith
238
223
224
235 241 247
237
217
227
221
216 233
228 234
237
229 230
219
229 231
231 243
236 248
222
232 244
231 243
233 245
234 246
235 241 247
Audio Setup Codes
ADC
Adcom
Aiwa
007
057 082 092 161 225
018 104 170 188 202 203 211
213
Akai
138 189
AMC
125 126 127 128 171 174
Amend
054
Angstrom
142
Arcam
141
Audio Access 147
Audio File
071
Audio Matrix 167
Audio Technica 134
B&K
096 097
Bose
070 170 224
Carver
006 022 028 029 061 071 077
185 201 214 226
Casio
076
Cinema Sound 001 134
Citation
122 148
Clarion
026
23
Curtis Mathes 076
Denon
001 002 011 027 037 109 215
229 230 234
Elnlightened Audio 098 099
Fisher
047 182 214
Fosgate
062 231
Goldstar
008
Harman/Kardon 003 118 121 132 154 227 231
233
Hitachi
020
Inkel
222
JC Penny
076 216
Jensen
058
JVC
056 114 149 155 163 191
Kenwood
005 026 066 145 146 151 162
181 182 190 192 199 222
Koss
216
Krell
072
Kyocera
007
Lexicon
120 180 194
Linn
124
Luxman
004 009 052 115 137 139 165
LXI
076
Magnavox
086 152 164 208
Marantz
006 025 028 031 040 054 063
185 186
Mcintosh
178
MCS
076
Meridian
012 013 100
Mitsubishi
153 204
Mondial
042 043 081 112 157 158
NAD
113 176 186
Nakamichi
103 111 150 172 183
Onkyo
017 046 079 080 084 090 107
108 130 179 187 209
Optimus
026 041 138
Panasonic
032 195
Philips
025 034 038 063
Pioneer
014 033 035 039 044 045 050
069 078 116 159 168 198
Proceed
135 144
RCA
010 048 067 117 156
Realistic
019 056 073 075 095
Rotel
074 083 085
Samsung
016
Sansui
040 048 065 110 119 228
Sanyo
047 059
24
Scott
Sears
Sharp
Sherwood
Sony
Soundesign
SSI
Taekwang
Teac
Theta Digital
Toshiba
Yamaha
Zenith
019 091
076
026 094 131 175 181
024 030 051 055 102 105 106
015 018 053 064 088 093 101
160 166 184 218
036
068
138
005 019 049 111 212 217
136
060 087 140 198
021 023 026 067 089 129 169
173 177 205 232
143 210
LD Setup Codes
Denon
Funai
Kenwood
Magnavox
Marantz
Mitsubishi
NAD
Optimus
Panasonic
Philips
Pioneer
Radio Shack
RCA
Realistic
Runco
Sanyo
Sharp
Sony
Technics
Theta Digital
Toshiba
Yamaha
250 251
245
236 249
237 246
252
246
246
236 239
243
237
244 246
245
235
239
247
241
236 249
240 242
243
237
246 249
238 248
DCR Setup Codes
DMX-DJ
Maestro II
254
255