Operating instructions | Contec RC-U49C-15+ Universal Remote User Manual

CheckMate® IV
Model RT-U49C+
Universal Remote Control
1. Introduction
Your CheckMate® IV universal remote control is
simple to program, easy to use, and can operate up to
four (4) devices, which include:
CABLE
TV
VIDEO
AUDIO
Cable set-top terminals
Televisions
VCR, DVD
Audio receivers, amplifiers, CD players
Before you can use your remote control, it must be
programmed (set-up) to operate the above devices.
[MODE]
Indicates which mode (CBL, TV, VIDEO, AUDIO)
the remote is currently operating in by illuminating
the power button. To change to a different mode,
press [MODE], then the power button for the
electronic device you wish to operate. For more
information, see Sections 10, 11, 12, 13, 16, 18.
Memory Guard™
Eliminates reprogramming after battery changes.
Time Out
+
2. Before Getting Started
-
Some of the special features and buttons on your
remote control are as follows:
Shuts remote off if any button is pressed and held
for 30 seconds. This extends battery life in the
event the remote becomes lodged under or between
heavy objects.
®
Point and Press Programming
3. Installing / Replacing Batteries
Lets you program your TV, VIDEO, AUDIO devices
without codes.. For more information, see Sections
5 and 18.
[ALL]
Turns all of your electronic devices on / off with one
button press. [ALL] can even be programmed to
automatically tune your TV to its correct output
channel. For more information, see Section 8.
Install two (2) new “AA” alkaline batteries as indicated
by the diagram in the battery compartment.
When the batteries become low and need to be
replaced, the [CBL], [TV], [VIDEO], [AUDIO] buttons
will not illuminate normally or at all during use.
When this happens, replace the existing batteries with
two (2) new “AA” alkaline batteries to restore normal
operation to the remote control.
[MOVIES], [SPORTS], [NEWS]
Program your favorite channels on the [MOVIES],
[SPORTS] and [NEWS] buttons.
For more
information see Section 9.
[VCR / VOD] Toggle
Programming And Operating
Instructions
To have a clearer idea of the features and capabilities of
your remote control, take a moment to read these
instructions. Save for future reference.
© 2003, CONTEC CORPORATION, Rev. 07/03
“Toggles” the VCR buttons between CABLE (VideoOn-Demand) and VIDEO (VCR / DVD) functions.
For more information, see Section 10.
4. Programming Your Cable Set-Top Terminalu
Your CheckMate® IV remote is pre-programmed to
operate the Scientific-Atlanta Explorer®, Pioneer
®
Voyager and Pace digital set-top terminals.
To operate a different cable set-top terminal, look up
the brand and model in the Cable Setup Code list. If
you are not sure of your brand and model, contact
your cable company.
SmartKeys™
Program multiple button presses on the [CBL] and
[TV] buttons. For more information, see Section 15.
1. Press [SELECT], then [MUTE] together until the
power / mode buttons illuminate in slow-rotation
(i.e. CBL Æ TV Æ VIDEO Æ AUDIO Æ CBL…).
2. From the Cable Setup Code list, locate the 3-
digit code for your brand / model and enter it on
the keypad of the remote control. The set-top
terminal will turn off.
3. Then, press [SELECT] to lock in the code. The
power / mode buttons will blink 3-times and go out.
3. a. To program your TV, locate the 3-digit code for
your brand in the TV Setup Code list and enter
it on the keypad of the remote control. Entry
of the correct code will cause your TV to turn
off. If multiple codes are listed for your brand,
you may have to enter several different codes
until your TV turns off.
•
There may be several codes that turn your
electronic devices on / off (or perform other
functions). Once you lock-in a code, be sure to
check the available functions for that device (i.e.
TV - Vol +/-, Mute, TV Input (TV / VCR button),
VIDEO - Play, Stop, Rew..., AUDIO - Volume /
Mute) to see if they are operating.
b. As soon as you have entered a 3-digit code
that turns your TV off, press [MUTE].
•
While the remote is searching for the correct
setup code(s) for your electronic devices, it is
possible that other (previously programmed)
devices may turn on / off (or perform other
functions). If this occurs, continue pressing the
[CH +] or [CH -] buttons (or the buttons described
in Section 18) until you find the correct code for
the device you are programming.
•
It may take several minutes for the remote to find
the correct code that turns your device on / off (or
performs another selected function). During this
time, the power / mode buttons will illuminate in
fast-rotation (i.e. CBL Æ TV Æ VIDEO Æ AUDIO
Æ CBL..).
Cable Setup Codes
Motorola
DCT, CFT2200
CFT2100, CFT2000
001
002
Jerrold
DL4, DP(V), DQN(V), DPBB
003
1. If the TV turns back on, press [SELECT] to
lock in the code. The power / mode
buttons will blink 3-times and go out.
Or
Scientific Atlanta
®
Explorer (default)
Explorer® (#, *)
®
Explorer (Blue Ridge)
Explorer® 8000 DVR
8600X
8600
Pace
510 Digital
HD Digital
2. If the TV does not turn back on, enter a
different 3-digit setup code until your TV
turns back on. Then press [SELECT] to
lock in the code. The power / mode
buttons will blink 3-times and go out.
004
010
011
412
005
006
4. To program your VCR or DVD, refer to the VCR /
DVD Setup Code lists and repeat steps 2 and 3
above.
004
010
Pioneer
Voyager®
BA-V1000, BA-V2000
004
007
Tocom
5503VIP, 5507, 5508
008
Zenith
MM 2500
Digital
009
013
5. Programming Your TV, VIDEO, AUDIO Devices
Code-Entry Programming
1. Turn on all the electronic devices (TV, VCR, DVD,
AUDIO) you want to program the remote to
operate.
2. Press [SELECT], then [MUTE] together until the
power / mode buttons illuminate in slow-rotation
(i.e. CBL Æ TV Æ VIDEO Æ AUDIO Æ CBL…).
5. To program your AUDIO devices, refer to the
AUDIO Setup Code list and repeat steps 2 and 3
above.
Point and Press® Programming
This method allows you to program the remote control
without using codes. Instead, the remote control
automatically finds the correct command that you
select in a variety of codes until you find the code that
operates your device. You then lock in the correct
code as described below.
The following instructions describe how to program
your remote control using the [CH +] or [CH -] buttons
("Power" function during programming). You can also
program your remote control using other buttons /
functions as described in Section 18. When using this
method, there are several important points to
remember:
•
The order in which you program your electronic
devices is not important.
Programming your electronic devices using the
[Ch +] or [Ch -] buttons (“Power” function during
programming)...
1. Turn on all the electronic devices (TV, VCR, DVD,
AUDIO) you want to program the remote to
operate.
2. Press [SELECT], then [MUTE] together until the
power / mode buttons illuminate in slow-rotation
(i.e. CBL Æ TV Æ VIDEO Æ AUDIO Æ CBL...).
3. Press and hold the [CH +] button until one device
turns off. While you are pressing the [CH +]
button, the power / mode buttons will illuminate in
fast-rotation. As soon as one device turns off,
release the [CH +] button.
4. Press [MUTE]. If the device that turned off...
a. Turns back on, press [SELECT] to lock in this
code. The power / mode buttons will blink 3times and go out.
Or
b. Does not turn back on, press [CH -] one step
at a time until that device turns back on. Each
time you press the [CH -] button, the power /
mode buttons will illuminate once in reverse
fast-rotation (AUDIO Æ VIDEO Æ TV Æ CBL).
Once you have found a code that turns the
device on / off, press [SELECT] to lock in this
code. The power / mode buttons will blink 3times and go out.
5. Repeat steps 2 to 4 above for each of the
remaining electronic devices you wish to program
the remote to operate.
Broksonic
Brokwood
Candle
Centurion
Citizen
Concerto
Contec
Coronado
Craig
Crown
Curtis Mathes
Daewoo
6. Programming Your TV / VCR Combination
1. First, turn on your TV / VCR combination device
and install a VHS tape.
2. Next, program your remote to operate the TV
functions.
Using the Code Entry Programming method
described in Section 5, find a TV Setup Code that
operates the TV functions (Power, Vol, + / -,
Mute) of your TV / VCR unit.
3. Last, program your remote to operate the VCR
functions.
Using the Code Entry Programming method
described in Section 5, enter, lock and test each
3-digit VCR Setup Code for your brand until a
code is found that operates the transport functions
(PLAY, STOP, REW, FWD, PAUSE, REC) of your
TV / VCR unit.
TV Setup Codes
Admiral
Adventura
Aiwa
Akai
Amark
Amstrad
Anam
AOC
Audiovox
Belcor
Bell & Howell
Daytron
Dumont
Electro Home
Elektra
Emerson
Envision
Fisher
Funai
GE
Gibralta
Goldstar (LG)
Grundig
Hall Mark
Hitachi
026
047
214
053
023
157
217
222
053
220
073
211
054 211
Inkel
JC Penney
215
JVC
218 219 220 221
223
Kawasho
KMC
KTV
Kurazai
LG (Goldstar)
165
073
068
095
068
073
147
023
223
023
016
213
051
159
197
205
073
073
073
353
016
139
166
400
073
355
047
015
054
095
390
023
090
360
023
107
233
073
023
098
364
039
095
104
410
073
023
023
211
023
107
167
Lodgenet
Logik
Luxman
LXI
Magnavox (Philips)
091
107 108
091 211 233
095
054 107 108 211
Majestic
Marantz
Megatron
Memorex
073
191
200
207
107
095 158
194 196
202 204
209
108
MGA/Mitsubishi
023
158
167
401
095
356
053
159
168
402
064
164
169
408
103
165
392
415
Panasonic
Philco
018
055
101
396
048
095
042
068
102
403
053
107
044
073
103
406
068
108
049
090
389
407
073
233
068
189
198
206
095
095
053 068 073 090
108 233 360 361
095
068 095 096 097
099 100
053 068 073 092
102 355
105 106 396 397
Montgomery Ward
NEC
Orion
Philips(Magnavox)
Pilot
Pioneer
Portland
ProScan
Proton
Pulsar
Quasar
Radio Shack
Realistic
RCA
Sampo
Samsung
Sanyo
Scott
Sears
Sharp
095
053 233 366
213
053 068 073 090
108 233 360 361
Signature 2000
Sony
Soundesign
Squareview
211
211
068
024
023
090
387
211
053
215
090
405
053
107
394
022
072
028
019
163
042
023
091
023
090
387
073
111
023
055
090
073
044
073
022
042
069
090
015
090
151
353
090
023
353
016
026
395
023
014
091
157
213
213
073
026
068
091
397
213
107
095
157
071 073 089
093 134 385
404
108 109
211 213 355 388
068
109
395
023
108
068
159
382
043
053
073
110
398
026
211
090
160
090
216
399
053
213
108
161
095
384
068
091
397
094
144
068
070
371
071 073 089
093 134 385
404
233
383
166
052
070
108
016
107
153
355
108
031
355
022
027
409
026
020
168
053 054 055
416
071
200
162
044 045 046
068 071 072
372
017
108
386
356
168
038
356
023
028
023 031
134 147
411
376 377
039 068
024 025
029 393
108 211 213
021
Supre-Macy
Sylvania
380
068
093
Symphonic
047
Tatung
044
Techwood
068
Teknika
023
213
Telerent
023
Tera
381
Tevion
065
TMK
068
Toshiba
030
Totevision
233
Universal
068
Vidtech
068
Wards
068
White Westinghouse 211
XR-1000
213
Yamaha
068
York
090
Zenith
047
391
071 072 090 091
107 108 157 158
157
068 072 091 168
213
414
090
031 038 039
102
090
408
Audio Dynamics
Bell & Howell
Broksonic
Canon
Citizen
Colortyme
Craig
Curtis Mathes
Daewoo
Daytron
DBX
Dynatech
Emerson
Fisher
Funai
GE
Go Video
Kenwood
LG (Goldstar)
Lloyd
Logik
LXI
Magnavox (Philips)
Marantz
Marta
Matsui
Memorex
108
048 049 050 051
405 406
VCR Setup Codes
Admiral
Adventura
Aiwa
Akai
Goldstar (LG)
Harman Kardon
Hitachi
Instant Replay
JC Penney
JCL
JVC
Mitsubishi
MTC
Montgomery Ward
Multi Tech
NEC
066 075
Orion
132
269
354
243
357
333
086
033
291
172
086
033
347
345
243
132
033
331
336
341
035
132
086
348
Panasonic
Pentax
Philco
Philips (Magnavox)
Pioneer
Portland
ProScan
Quartz
Quasar
RCA
275 336 351 352
291
337 358 359
362
172 247 331
363
112 247 291
343 344 345 346
365
291
086
332
337
342
081
132 326 327
333 334 335
338 339 340
357 363
172 174
349 350
Realistic
Samsung
Sansui
Sanyo
Scott
Sears
Sharp
Shintom
Signature 2000
Sony
Soundesign
Sylvania
247
291
078
086
078
086
120
253
120
247
132
367
132
086
086
291
331
368
132
370
255
132
066
132
120
375
322
330
112
078
086
086
078
345
170
238
112
078
173
066
269
120
238
033
035
066
367
066
056
132
086
322
331
132
086 172 238 291
128 243 247 250
132 238 243 247
331
331
132 183
172 183 238 247
Symphonic
Tandy
Tashiko
Tatung
Teac
Technics
Teknika
Thomas
TMK
Toshiba
Totevision
Unitech
Vector Research
Video Concepts
Wards
XR-1000
Yamaha
Zenith
132
132
331
243
132
086
132
132
338
033
172
172
291
132
066
367
132
058
238
243
331 359
035 078 081
331
291
132 172 247 331
243 291
120 122 128 132
238 331 363 369
DVD Setup Codes
258
172
170 173 373
172 367
238 243 291 374
326 327 328 329
117
132 183
132 183
120 263
174
378
132
174
132
271
367
346
332
078
075
141
416
238
275
379
357
367
238
170 172
363
276 278
363
331 363
170 173 373
058 060
132 141 183 184
324
Apex Digital
B144
Denon
DVD-Video
ECA
GE
Goldstar (LG)
Gradiente
Harmon Kardon
Hitachi
JVC
Kenwood
KLH
LG (Goldstar)
Magnavox
Marantz
Mitsubishi
NAD
Onkyo
Panasonic
Pioneer
Proceed
Samsung
Sharp
Sony
Thomson
Toshiba
Yamaha
Zenith
193
146
201
199
156
150
129
212
256
149
177
228
248
129
138
270
181
246
085
115
125
236
192
034
040
156
082
121
129
227
203
152
133
234
259
156 175
135 179 260
179
252
133
143
135 179 260
146
185
244
118
187
224
076
059
237
085
124
133
121 124
188
225
077 079
061
087 113
210
135
AUDIO Setup Codes
Compact Disc
ADC
Akai
Aiwa
Carver
Crown
Denon
Fisher
Goldstar (LG)
Harman Kardon
JVC
Kenwood
Krol
LG (Goldstar)
Magnavox (Philips)
Mission
Mitsubishi
NAD
Nakamichi
NEC
NSM
Onkyo
Panasonic
Philips (Magnavox)
Pioneer
Quasar
Radio Shack
RCA
Sanyo
SAE
Scott
Sharp
Sony
Soundesign
STS
Sylvania
Teac
Technics
Toshiba
Yamaha
318
249
176
176
154
273
230
308
315
297
131
176
308
037
176
245
182
264
235
176
300
184
037
116
184
186
295
230
176
186
288
067
148
318
084
186
184
290
280
261
274
176 274 289 299
084 119 296
249
231 290
319
266
084 119 296
127
190 266 279 289
309
289
292 293
242 311 320
136
063
305
036
130
240
140
114
063
036
281
080
282
286
126
142
032
323
080
123
032
229
226
310
283
195
272
294
229
041
083
313
142
314
032
063
114
145
036
180
257 305 306
241
277
2. Press [INFO]. The [TV] button will “blink back” the
code numbers, with a 1-second interval between
each digit of the code.
Example: For code “035”, the remote will blink
10 times, then 3 times, then 5 times.
To identify the 3-digit VIDEO code, press [VIDEO],
then [SELECT] in step 1, then press [INFO].
To identify the 3-digit AUDIO code, press [AUDIO],
then [SELECT] in step 1, then press [INFO].
283 284 285
171 304
229 321
074
137 251 298
267
268
8. [ALL] Button
Once you have programmed each of your devices,
press [ALL] to turn all of them on / off with a single
button press. You can also program the [ALL] button
to tune your TV to its correct output channel.
Programming the [ALL] Button
If you would like the [ALL] button to also tune your TV
to its correct output channel (typically 3) follow these
steps:
267
057 232 287
088 239 265
316
241
254 303
083 088 239 265
1. Press [MODE], then [CBL] to select the remote’s
cable mode.
2. Press [SETTINGS], then [ALL] together until the
[TV] button illuminates.
3. Press [0], then [3] X,Y.
4. Press [CH S] to store the TV channel. The [TV]
button will blink 3-times and go out.
X Your TV output channel may also be 2 or 4. If you
are not sure, contact your cable operator.
208 317
Receiver / Amplifier
Adcom
Aiwa
Akai
Bose
Carver
Denon
Everquest
Fisher
Fosgate Audionics
Goldstar (LG)
Harman Kardon
Hitachi
Jensen
JVC
Kenwood
LG (Goldstar)
Luxman
Magnavox
Marantz
NAD
Onkyo
Optimus
Panasonic
Parasound
Philips (Magnavox)
Pioneer
Quasar
Radio Shack
Realistic
Rotel
Sansui
Sanyo
Scott
Sharp
Sherwood
Sony
Soundesign
SSI
Taekwang
Teac
Technics
Wards
Victor
Yamaha
Zenith
325
301
142
302
155 180
262 307
7. Code Number Read-Back
Y Depending on your TV brand, the channel may
have to be entered as “3”, “03” or “003”.
To identify the 3-digit setup codes stored under the
Point and Press® programming method, follow these
steps:
Using the [ALL] Button
To identify the TV setup code…
When pressing the [ALL] button, be sure to keep the
remote control aimed at your electronic devices until
your electronic devices turn on or / off.
1. Press [TV], then [SELECT] together until the [TV]
button illuminates.
Resetting the [ALL] Button
1. Press [MODE], then [CBL] to select the remote’s
cable mode.
[MOVIES] button any time after entering a
complete channel number.
2. Press [SETTINGS], then [ALL] together until the
[TV] button illuminates.
4. Repeat the above steps to program the [SPORTS]
and [NEWS] buttons. Follow the example in step
1, but press [SPORTS] or [NEWS], then [CBL]
together until the [CBL] button illuminates.
3. Press [CH S]. The [TV] button will blink 3-times
and go out.
Using [MOVIES], [SPORTS], [NEWS]
9. [MOVIES], [SPORTS], [NEWS] Buttons
Your remote has 3 Channel Memory Buttons –
[MOVIES], [SPORTS], [NEWS] (may be labeled
differently on some models). Each of these buttons
can store up to 5 cable channels. Each cable channel
can be up to 5-digits.
Some or all of your remote’s Channel Memory
Buttons may come pre-tuned to channels or functions
selected by your cable operator. If they have not
been pre-tuned by your cable operator, they can be
programmed as follows:
Programming [MOVIES], [SPORTS], [NEWS]
To program the [MOVIES] button to cable channels 1,
12, 123, 231 and 17, follow these steps:
1. Press [MOVIES], then [CBL] together until the
[CBL] button illuminates.
2. Enter each channel as follows:
a. Enter 1st channel # - 001.
b. Press [CH +] to advance to next channel #
setting.
nd
c. Enter 2 channel # - 012.
d. Press [CH +] to advance to next channel #
setting.
e. Enter 3rd channel # - 123.
f. Press [CH +] to advance to next channel #
setting.
th
g. Enter 4 channel # - 231.
h. Press [CH +] to advance to next channel #
setting.
i. Enter 5th channel # - 017.
Using the above programmed channels as an
example…
1. Press [MOVIES] – Cable set-top terminal tunes to
channel 001.
2. Press [MOVIES] again – Cable set-top terminal
tunes to channel 012.
3. Press [MOVIES] again – Cable set-top terminal
tunes to channel 123.
4. Press [MOVIES] again – Cable set-top terminal
tunes to channel 231.
5. Press [MOVIES] again – Cable set-top terminal
tunes to channel 017.
6. Press [MOVIES] again – Cable set-top terminal
tunes to channel 1…. repeat.
Whenever a Channel Memory button is pressed, the
function of the transport buttons will automatically
switch back to Cable.
When pressing the [MOVIES] button, be sure to keep
the remote control aimed at your Cable set-top
terminal to ensure the full channel numbers are
received in their entirety.
Resetting [MOVIES], [SPORTS], [NEWS]
To reset [MOVIES], [SPORTS], [NEWS], follow these
steps:
[ALL]
[CBL]
[TV]
[VIDEO]
[AUDIO]
[CH S] / [CH T]
ALL devices on / off.
Cable set-top terminal on / off.
TV on / off.
VCR / DVD on / off.
Audio on / off.
Increases / decreases cable
channel.
[VOL S] / [VOL T] Increases / decreases volume.
[MUTE]
Mute volume.
[EXIT]
Exits on-screen menus, view
guide, interactive screens.
[SETTINGS]
Displays program settings.
[GUIDE]
Displays interactive program
guide.
[INFO]
Displays
channel,
time
information.
[FAV]
View favorite channels.
[LAST]
Last channel viewed.
[A], [B], [C]
On-screen decision buttons.
[0] - [9]
Numeric entry buttons.
[PAGE S/T]
Page up / down through menus,
program guide.
[], [], [], [] Navigate on-screen menus,
program guide, PPV events and
interactive services.
[SELECT]
Select menu, interactive screen
item.
[BYPASS]
Switch between set-top terminal
and TV.
[TV / VCR]
Changes VCR Video inputs.
[VCR / VOD]
“Toggles” the VCR buttons
between cable VOD (Video-OnDemand) and VCR / DVD
functions.
Press [VCR / VOD]. If...
1. Press [MOVIES], then [CBL] together until the
[CBL] button illuminates.
2. Press [MOVIES]. The [CBL] button will blink 3times and go out.
a. [CBL] illuminates, the VCR
buttons are operating your
cable VOD functions.
OR
10.
3. Press [MOVIES] to store the above channels. The
[CBL] button will blink 3-times and go out. To
store fewer than 5 channels, you can press the
To operate your CABLE set-top terminal, press
[MODE], then [CBL]. In your remote’s CABLE
mode, you can then press…
Operating Your Cable Set-Top Terminal
Your remote control is designed to operate all the
features and functions of your digital set-top terminal.
[VIDEO] illuminates, the
VCR buttons are operating
your VCR or DVD functions.
b. While [CBL] or [VIDEO] is
illuminated, press [VCR /
VOD] to switch from VOD to
VCR or VCR to VOD.
[ ]
[]
[]
[ ]
[ ]
]
[
[MOVIES]
[SPORTS]
[NEWS]
11.
VCR / DVD or VOD rewind.
VCR / DVD or VOD play.
VCR / DVD or VOD fast-forward.
VCR / DVD or VOD pause.
VCR / DVD or VOD stop.
VCR / DVD or VOD record.
Programmable favorite channel.
Programmable favorite channel.
Programmable favorite channel.
Operating Your TV
Your remote control can operate many functions of
your TV.
To operate your TV, press [MODE], then [TV]. In
your remote’s TV mode, you can then press…
[ALL]
ALL devices on / off.
[CBL]
Cable set-top terminal on / off.
[TV]
TV on / off.
[VIDEO]
VCR / DVD on / off.
[AUDIO]
Audio on / off.
[CH S] / [CH T] Increases / decreases channel.
[0] – [9]
Numeric entry buttons.
[VOL S] / [VOL T] Increases / decreases TV
volume.
[MUTE]
Mute TV volume.
[TV / VCR]
Change TV’s video inputs.
[]
VCR / DVD rewind.
VCR / DVD play.
[]
[]
VCR / DVD fast-forward.
VCR / DVD pause.
[ ]
[ ]
VCR / DVD stop.
]
VCR / DVD record.
[
12. Operating Your VIDEO (VCR or DVD) Device
Your remote control can operate many functions of
your VCR or DVD.
To operate your VCR or DVD, press [MODE] then
[VIDEO]. In your remote’s VIDEO mode, you can
then press…
[ALL]
ALL devices on / off.
[CBL]
Cable set-top terminal on / off.
[TV]
TV on / off.
[VIDEO]
VCR / DVD on / off.
[AUDIO]
Audio on / off.
[CH S] / [CH T] Increases / decreases channel.
[0] – [9]
Numeric entry buttons.
[VOL S] / [VOL T] Increases / decreases TV
volume.
[MUTE]
Mute TV volume.
[TV / VCR]
Change VCR video inputs.
VCR / DVD rewind.
[ ]
VCR / DVD play.
[ ]
[ ]
VCR / DVD fast-forward.
VCR / DVD pause.
[ ]
[ ]
VCR / DVD stop.
]
VCR / DVD record.
[
13. Operating Your AUDIO Device
To operate your AUDIO device, press [MODE],
then [AUDIO]. In your remote’s AUDIO mode, you
can press…
[ALL]
ALL devices on / off.
[CBL]
Cable set-top terminal on / off.
[TV]
TV on / off.
[VIDEO]
VCR / DVD on / off.
[AUDIO]
Audio on / off.
[CH S] / [CH T] Increases / decreases channel.
[0] – [9]
Enter channels.
[VOL S] / [VOL T] Increases / decreases volume.
[MUTE]
Mute volume.
Rewind.
[]
[]
Play.
Fast-forward.
[]
[]
Pause.
Stop.
[ ]
[
]
Record.
14. Programming Volume Control
When you first program your remote, volume / mute
are controlled through your TV (except AUDIO which
defaults to the AUDIO device).
The volume control options in each mode of the
remote are:
CBL
TV
VIDEO
AUDIO
TV (default), Cable or Audio.
TV (default), Cable or Audio.
TV (default), Cable or Audio.
AUDIO device (default), Cable or TV.
To control volume / mute through your Cable settop terminal in the remote’s cable mode…
1. Press [CBL], then [SELECT] together until the
[CBL] button illuminates.
2. Press [VOL S], then [CBL] for Cable volume. The
[CBL] button will blink 3-times and go out.
To return volume control to your TV, repeat step 1,
then press [VOL S], then [TV] in step 2.
15.
Your Remote's SmartKeys™
Your remote has two (2) SmartKeys™ - [CABLE] and
[TV] that operate in its cable mode.
Each
SmartKey™ can be programmed to transmit multiple
functions.
Programming and using the [CBL] SmartKey™
The [CBL] button normally turns on / off your cable
set-top terminal. To program the [CBL] button to
transmit multiple pre-programmed functions, follow
the steps below:
1. Press [MODE], then [CBL] to select the cable
mode of your remote.
2. Press [CBL], then [SETTINGS] together until the
[CBL] button illuminates.
3. Press the option number below for the desired
functions:
Option
Pre-Programmed to turn on…
[1]
[2]
[3]
Cable & TV - tune TV to Ch 3
Cable & TV - tune TV to Ch 2
Cable & TV - tune TV to Ch 4
[4]
[5]
[6]
Cable, TV & VIDEO - tune TV to Ch 3
Cable, TV & VIDEO - tune TV to Ch 2
Cable, TV & VIDEO - tune TV to Ch 4
[7]
[8]
Cable, TV, VIDEO & AUDIO - tune TV to
Ch 3
Cable, TV, VIDEO & AUDIO - tune TV to
Ch 2
[9]
Cable, TV, VIDEO & AUDIO - tune TV to
Ch 4
[0]
Cable only (default)
seconds and the remote will exit the programming
mode.
button illuminates.
2. Press [0, 0, 0]. The [CBL] button will blink 3-times
and go out.
4. The [CBL] button will blink 3-times and go out,
storing the selected option.
To unlock
operation…
your
remote
for
multi-device
Programming and using the [TV] SmartKey™
1. Press [CBL], then [MUTE] together until the [CBL]
button illuminates.
The [TV] button normally turns on / off your TV. To
program the [TV] button to transmit multiple preprogrammed functions, follow the steps below:
2. Press [9, 9, 9]. The [CBL] button will blink 3-times
and go out.
1. Press [MODE], then [CBL] to select the cable
mode of your remote.
17.
2. Press [TV], then [SETTINGS] together until the
[TV] button illuminates.
3. Press the option number below for the desired
functions:
Option
Pre-programmed to turn on…
[1]
[2]
[3]
TV - tune TV to Ch 3
TV - tune TV to Ch 2
TV - tune TV to Ch 4
[0]
TV only (default)
OR
This button changes the input source of your
electronic devices. In the remote's Cable and TV
modes, this button operates the TV Input function on
your TV. In the remote's VIDEO mode, this button
changes the TV / VCR function on your VCR.
You can program this button so that in the remote's
cable mode, [TV / VCR] will operate the TV / VCR
function on your VCR, eliminating the need to change
modes on the remote.
To program the [TV / VCR] button to operate your
VCR Input function…
1. Press [TV / VCR], then [SELECT] together until the
[CBL] button illuminates.
Note: When using any SmartKey™ to transmit a
series of functions, be sure to keep your remote
aimed at the devices to ensure all functions are
received in their entirety.
2. Press [VIDEO]. The [CBL] button will blink 3-times
and go out.
Mode Lock™
®
Your model CheckMate IV remote comes set in its
“unlocked” operating mode. While in this mode, it can
operate all of your cable set-top functions, as well as
many functions on your TV, VIDEO and AUDIO
devices.
To lock your remote in its cable operating mode...
1. Press [CBL], then [MUTE] together until the [CBL]
a. The correct code has not been found as
you may have a code that operates some
but not all of the functions of your device.
Continue pressing [CH +] until your device
turn on.
TV / VCR Input
4. The [TV] button will blink 3-times and go out,
storing the selected option.
16.
2. When programming the remote control using the
[CH +] or [CH -] buttons (Power function) under
®
the Point and Press Programming method, you
may find a code that turns a device off but not
back on. If this happens…
To return this button to operate the TV Input function
on your TV, repeat step 1, then press [TV] in step 2.
18.
Additional
Programming
Troubleshooting, Tips
Information,
b. You may have gone past the correct matching
code. Try pressing [CH -] one press at a time
until you find a code that turns your device
back on.
3. When using the Point and Press® Programming
method, you can also program your remote using
buttons other than the [CH +] or [CH -] (as
described in Section 5) as follows:
a. [VOL +] – to “go forward” through the codes
using the “VOL +” function on your devices.
b. [VOL -] – to “go back” through the codes using
the “VOL -“ function on your devices.
Note: When you find the correct code, the
volume of the device being programmed will
increase or decrease.
c. [S] - to “go forward” through the codes using
the “CH +” function on your devices.
d. [T] - to “go back” through the codes using the
“CH -“ function on your devices.
Note: When you find the correct code, the
channel of the device being programmed will
increase or decrease.
Additional Programming Information
1. The power / mode buttons will illuminate in
slow-rotation (i.e. CBL Æ TV Æ VIDEO Æ AUDIO
Æ CBL...) while the remote is in a programming
mode. In the absence of a keypress entry, the
power / mode buttons will stop illuminating after 30
e. [XX] - to “go forward” through the codes using
the “Fast Forward” function on your devices.
f.
[WW] - to “go back” through the codes using
the “Rewind” function on your devices.
Note: When you find the correct code, the
fast-forward or rewind function of the device
being programmed will be performed. To
simplify programming using these buttons,
insert a VHS tape or DVD in the device being
programmed.
You can also program your remote using the other
available functions as follows:
a. Press [SELECT], then [MUTE] together until
the power / mode buttons illuminate in slowrotation (i.e. CBL Æ TV Æ VIDEO Æ AUDIO
Æ CBL...).
b. In this order, carefully press [0], [0], [0], [CH+]
and [VOL+]. The power / mode buttons
illuminate in slow-rotation (i.e. CBL Æ TV Æ
VIDEO Æ AUDIO Æ CBL...).
c. You can now program your remote using the
[CH+], [CH -], [VOL+], [VOL -], [S], [T],
[FFWD], [REW], [PLAY], [STOP], [REC],
[PAUSE], [LAST], [FAV], [0] - [9] buttons.
When you find the correct code, the function
associated with the selected button will be
performed.
®
4. Your remote is equipped with a Point and Press
Programming label on the back of its case. This
will help you quickly program the remote without
using codes.
Troubleshooting / Tips
1. If the same button is pressed and held for 30
seconds, your remote control will turn itself off
automatically. This extends the battery life should
the remote become lodged under or between
heavy objects, for example sofa cushions.
2. If you have a TV that’s operated by remote
control, it is recommended that you plug it directly
into a wall outlet instead of the cable set-top
terminal.
3. If you have any questions concerning the brand,
model or operation of your cable set-top terminal,
contact your cable operator.
4. If the [MODE] button is not operating, the remote
is in its locked mode. To set the remote to its
unlocked mode, see Section 16.
Frequently Used Terms
AUDIO Devices - Audio receivers, amplifiers, CD
players that you can program your remote to operate.
Default Setting – How your remote is set when you
receive it from your cable operator.
Electronic Components / Devices - The various
electronic devices the remote is designed to operate.
These include cable set-top terminals, TVs, VCRs,
DVDs, Audio receivers, amplifiers and CD players.
VIDEO Devices - VCR or DVD players.
Rev. 07/03
© 2003, CONTEC CORPORATION
®
®
CheckMate and Point and Press are registered
trademarks of Contec Corporation
Explorer® is a registered trademark of ScientificAtlanta, Inc.
®
Voyager is a registered trademark of Pioneer New
Media Technologies, Inc.
U.S. Patent 6,507,306
Fast-Rotation - The power / mode buttons will
illuminate in a fast sequence (i.e. CBL Æ TV Æ
VIDEO Æ AUDIO Æ CBL...) repeated every 1/3
second. Fast-rotation occurs when the remote is
receiving keypresses to program it to your electronic
devices.
Mode - The device the remote is set to operate (ex.
CABLE, TV, VIDEO, AUDIO). See Section 16 for
locking and unlocking the mode of the remote control.
Program (Setup) – the process of teaching your
remote control to operate your electronic devices.
Slow-Rotation - The power / mode buttons illuminate
in a slow sequence (i.e. CBL Æ TV Æ VIDEO Æ
AUDIO Æ CBL...) repeated every 1 second. Slowrotation illumination occurs when the remote is in the
programming mode, waiting for the next entry on the
keypad of the remote.
TV Output Channel - The channel your TV needs to
be set on for proper Cable reception (most often TV
channel 3, but may be TV channel 2 or 4). If you
have any questions concerning your TV output
channel, contact your cable operator. Or, with your
cable set-top terminal turned on, try setting your TV to
channel 2, 3 or 4 to obtain a clear picture.
Transport Functions - These are the [STOP], [PLAY],
[FWD], [REW], [PAUSE] and [REC] buttons. In the
remote's Cable mode, these buttons operate your
Cable set-top features. In the remote's VIDEO mode,
these buttons operate your VCR or DVD functions.
19. Using Your RT-U49C+ Remote Control
Illuminate / select device being
operated. Press [Mode], then…
ALL devices on / off
Display channel information
[CBL] - for Cable mode
[TV] - for TV mode
[VIDEO] - for VCR / DVD mode
[AUDIO] - for Audio mode
Power on / off for each device
Display Program Guide
Display program settings
Select interactive screen choice
Page +/- through screens
+
-
Hides interactive screens
Increase or decrease channel
Recall favorite channels
Navigates (S,T,W, X) through
interactive screen choices
Toggles between Cable, Video or
Audio functions as follows:
Mutes volume
Press [VCR / VOD] once. If the…
Increase or decrease volume
On-screen decision buttons
Enter channel, PIN numbers
Recall last channel
Cable, Video, Audio
transport functions
Bypass Cable set-top terminal
and tune directly to TV
TV or VCR input
Channel Memory Buttons
(may be labeled differently or
pre-set on some models)
[CBL] button illuminates, VCR
buttons are operating Cable VideoOn-Demand (VOD) functions
[VIDEO] button illuminates,
VCR buttons are operating
VCR or DVD functions
[AUDIO] button illuminates,
VCR buttons are operating
Audio (CD) functions
While button illuminated,
press [VCR / VOD] again to
switch from Cable to Video,
Video to Audio, Audio
to Cable
Note: Some models may have
VCR / VOD slide switch`
Download PDF

advertising