Contec RT-U49C Universal Remote User Manual

2
3
1. Introduction
Your CheckMate™ IV (Model RT-U49C) universal
remote control is simple to program, easy to use, and
can operate up to four (4) devices, which include:
Reset
Lets you reset your remote to its original default
settings. For more information, see section 17.
CABLE
TV
VIDEO
AUDIO
Cable set-top terminals
Televisions
VCR, DVD
Cassette deck, CD, receivers,
amplifiers, 2nd TV, 2nd VCR.
Before you can use your remote control, it must be
programmed (set-up) to operate the above devices.
2. Before Getting Started
Some of the special features and buttons on your
remote control are as follows:
Point and PressTM Programming
Let’s you program your TV, VCR Audio devices
without codes. For more information, see sections
5, 6 and 7.
[ALL]
Turns all of your devices on / off with one button
press. [ ALL ] can even be programmed to
automatically tune your TV to its correct output
channel. For more information, see section 8.
[Movies], [Sports], [News]
Program your favorite channels on the “Movies”,
“Sports” and “News” buttons. For more information
see section 9.
[VCR / VOD] Toggle
“Toggles” the VCR buttons between cable VideoOn-Demand (VOD) and VCR / DVD functions. For
more information, see section 10.
SmartKeysTM
Program multiple button presses on the [CBL], [TV]
and [BYPASS] buttons. For more information, see
section 15.
[DEVICE]
Tells which device you are currently operating by
illuminating the device’s power button. While the
current device is illuminated, press a nonilluminated
power button to operate a different device.
Memory GuardTM
Eliminates reprogramming after battery changes.
Time Out
Shuts remote off if any button is pressed and held
for 45 seconds. This extends battery life in the
event the remote becomes lodges under or
between heavy objects.
3. Installing / Replacing Batteries
Install two (2) new “AA” batteries as indicated by the
diagram in the battery compartment.
When the illuminated buttons become dim or do not
illuminate during use, install two (2) new “AA” size
batteries.
Your remote control has Memory GuardTM, which
eliminates reprogramming after battery changes.
4. Programming Your Cable Set-Top Terminal
Model RT-U49C is pre-programmed to operate
the Scientific-Atlanta Explorer , Pioneer Voyager
and Pace 510 digital set-top terminals.
To operate a different cable set-top terminal, look up
the brand and model in the Cable Setup Code list. If
you are not sure of your brand and model, contact
your cable company.
To program your cable set-top terminal...
1. Turn on your cable set-top terminal.
2. Press [CBL], then [SELECT] together - hold both
buttons down until [CBL] illuminates.
3. From the Cable Setup Code list, locate and enter
the 3-digit code for your brand and model.
4. Press [CBL] to lock in the code. The [CBL]
button will blink and go out.
Write your cable set-top terminal brand & setup
code__________
Refer to section 16 for code number readback.
Cable Setup Codes
Motorola (General Instrument)
DCT, CFT 2200
001
CFT2100, CFT2000
002
Jerrold
003
DL4, DP(V), DQN(V), DPBB
Scientific Atlanta
Explorer
004
Explorer(#, *)
015
Explorer(Blue Ridge)
016
Explorer(WorldGate™)
018
8600X
005
8600
006
8540, 70, 90
007
4
Pace
510 digital
Philips
digital
Pioneer
Voyager
BC-4600, BA-6000
BA-9000
BA-V1000, BA-V2000
Tocom
5503VIP, 5507, 5508
Zenith
Z-Tac
MM2500
Oak
Sigma One, P1, P2, P3
Sigma 2000
004
017
004
008
009
010
011
012
013
014
5. Programming Your TV
If you have a TV that’s operated by remote control, it
is recommended that you plug it directly into a wall
outlet instead of the cable set-top terminal.
To program your TV...
1. Turn on your TV.
2. Press [TV], then [SELECT] together - hold both
buttons down until [TV] illuminates.
3. a. Press and hold [CH +] until your TV turns off.
As soon as your TV turns off, release [CH +].
OR
b. From the TV Setup Code list, locate and enter
a 3-digit code for your brand. If multiple codes
are listed, you may have to enter several codes
until your TV turns off.
4. Press [MUTE]. If your TV turns back on, press
[TV] to lock in the code. The [TV] button will blink
and go out.
If your TV does not turn back on, repeat steps 3
and 4 until you can turn your TV off and on❶ .
.
Write your TV brand & setup code
Refer to section 16 for code number readback.
❶ Note When using the Point and PressTM
Programming method (step 3a). If you find a code
that turns your TV off but not back on (step 4),you
may have gone past the correct matching code. Try
pressing [CH–] one press at a time until you find a
code that turns your TV back on.
5
To program your TV / VCR combination unit...
1. First, program your remote as a TV
Following the steps in this section, find a TV Setup
Code that operates the TV functions of your TV /
VCR (power, vol + / – , mute, ch + / – 0 – 9).
2. Then, program your remote as a VCR
Following the steps in Section 6 for code number
programming, enter, lock and test each 3-digit
VCR Setup Code until a code is found that
operates the VCR functions of your TV / VCR
(play, stop, fast-forward, rewind, pause, record).
Note: You can not use the Point and PressTM
Programming method to program the VCR
functions of the TV / VCR.
TV Setup Codes
Admiral
Adventura
Akai
Aiwa
Amark
Ampro
Amstrad
Anam
AOC
Audio Vox
Belcor
Bell & Howell
Broksonic
Brokwood
Candle
Centurion
Citizen
Concerto
Contec
Coronado
Craig
Crown
Curtis Mathes
Daewoo
Daytron
Dumont
Electro Home
Elektra
Emerson
Envision
Fisher
Funai
058 061 062 067
004
065
135
007 086
112
006
088 089 093 111 120 125 134
065
111
041
062
011 054
041
027 052
044 051
027 052 059 062
041 051
020
007
134
007
044 061 062
027 039 040 041 042 051 090 091
092 094 101 102 108 114 118 121
123 130
041 044 051
041
041 051
002
007 008 011 012 017 054 065 079
108 110 131
041 051
010 028
004
6
GE
Gibralta
Goldstar(LG)
Grundig
Hall Mark
Hitachi
Inkel
JC Penney
JVC
Kawasho
KMC
KTV
Kurazai
Lodgenet
Logik
Luxman
LXI
Magnavox(Philips)
Majestic
Marantz
Megatron
Memorex
MGA/Mitsubishi
Montgomery Ward
NEC
Orion
Panasonic
Philco
Philips(Magnavox)
Pilot
Pioneer
Portland
ProScan
Proton
Pulsar
Quasar
Radio Shack
Realistic
RCA
Sampo
Samsung
Sanyo
Scott
005 019 027 031 037 041 046 051
053 055 061 070 131
007 025 027 031 041 044 051 059
060 065
007 027 031 041 044 059 060 065
124
059
041 051
007 027 049 051 083 085 098 100
075
005 010 027 037 041 051 065 069
070
048 077 080 132
041 051
007
007 030 059 065
062
062
062
027 041 051
006 035 067
001 005 007 014 026 027 041 052
068 081
062
003 065 076
086
010 031 062
003 027 031 041 044 051 065 076
084
007 037 044 057 058 062 065 067
081
023 027 031 044 101
013 017 033 045 047 078
018 019 021 024 053 063
001 007 027 052 065 081
001 005 007 014 026 027 041 052
068 081
041 059 097
056 103
007 027
055 061 073 082 112
031 126 128
041
019
041
012 057 079
022 027 046 053 055 061 065 072
073 082
031 044
007 016 020 031 044 119 129
002 010 028 104 133
031 044 079
7
Sears
002 007 010 016 027
028 043 069
Sharp
007 009 023 035 057 064 067 096
Signature 2000 007 044 058 062 067
Sony
032 038 050 066
Soundesign
052
Squareview
006
Supre-Macy
071
Sylvania
001 005 006 026 027 031 044 052
081 108
Symphonic
004 006
Tatung
019
Techwood
027
Teknika
001 007 027 052 062 079
Telerent
007 062
TMK
027 031
Tera
127
Toshiba
016 029 043 069
Totevision
059
Universal
027 070
Vidtech
027
Wards
027 031
White Westinghouse 058
XR-1000
062
Yamaha
027
York
031 044
Zenith
004 015 025 034 036
6. Programming Your Video (VCR / DVD)Device
To program your VCR or DVD...
1. Turn on your VCR or DVD.
2. Press [VIDEO], then [SELECT] together - hold
both buttons down until [VIDEO] illuminates.
3 a. Press and hold [CH +] until your VCR or DVD
turns off. As soon as your VCR or DVD turns
off, release [CH +].
OR
b.From the VCR - DVD Setup Code list, locate
and enter a 3-digit code for your brand. If
multiple codes are listed, you may have to enter
several codes until your VCR or DVD turns off.
4. Press [MUTE] If your VCR or DVD turns back on,
press [VIDEO] to lock in the code. The [VIDEO]
button will blink and go out.
If your VCR or DVD does not turn back on, repeat
steps 3 and 4 until you can turn your VCR or DVD
off and on❶ .
Write your VCR / DVD brand & setup code
.
Refer to section 16 for code number readback.
8
❶ Note When using the Point and Press™
Programming method (step 3a). If you find a code
that turns yourVCR/DVD off but not back on (step 4),
you may have gone past the correct matching code.
Try pressing [CH –] one press at a time until you find
a code that turns your VCR / DVD back on.
VCR Setup Codes
Admiral
Adventura
Aiwa
Akai
Audio Dynamics
Bell & Howell
Broksonic
Canon
Citizen
Colortyme
Craig
Curtis Mathes
Daewoo
Daytron
DBX
Dynatech
Emerson
014 056
025
025 106
011 021 051 092 098 103
007 044
005 024
009 048 053 064
008 034 105
002 006 028 060
044
028 030
008 013 034 044 060
006 010 012 057 058 112 114 116
055 058
007 044
025 106
002 003 006 008 009 022 033 040
049 051 064 091 101 106 107 109
Fisher
005 015 024 030 052
Funai
025 106
GE
008 027 028 034 041
Go Video
019 043 063
Goldstar(LG)
002 060
Harman/Kardon 044
Hitachi
025 046 059 106 113
Instant Replay 008 017 034
JC Penney
005 008 017 028 034 044 046
JVC
004 005 007 038 026 060 095 102
JCL
008
Kenwood
004 005 007 060 106
Logik
042
Lloyd
025 106
LXI
002 025 106
Magnavox
008 025 034 036 106
Marantz
005 008 036 044 060
Marta
002
Matsui
094
Memorex
002 005 025 030 034 104 106 110
Mitsubishi
023 029 031 047 106
MTC
025 028 106
Montgomery Ward 014 025 027 034 037 062
Multi Tech
025 028 042 106
NEC
004 005 007 044 070 071
Orion
022 049 065 066 067 068
Panasonic
008 013 034 099
Pentax
046
Philco
008 034 036 106
Philips
008 017 034 036 106
Pioneer
004 045 046
9
Portland
ProScan
Quasar
Quartz
RCA
058
027 041
013 034
005 009
001 008 016 017 027 028 037 041
046 106
Realistic
005 014 025 030 034 106
Samsung
021 028 039 098 108 111
Sansai
042
Sansui
004 093
Sanyo
005 024 114
Sayyo
030
Scott
003 006 031 042
Sears
002 005 015 030 046
Sharp
014 056
Shintom
042
Signature 2000 014 025 027 037 062
Sony
032 035 050
Soundesign
106
Sylvania
008 016 017 025 034 036 047 054
065 073 074 106
Symphonic
025 106
Tandy
005 025 106
Tashiko
002
Tatung
007
Teac
007 025 106
Technics
008
Teknika
002 053 106
Thomas
106
TMK
091
Toshiba
006 015 046 052 096
Totevision
002 028
Unitech
028
Vector Research 031 044
Video Concepts 044 106
Wards
002 014 025 028 060 106
XR-1000
042
Yamaha
005 007 044 106
Zenith
004 018 035 038 061 106
DVD Setup Codes
Denon
076
GE
077 078
Hitachi
117
JVC
079
KLH
118
LG
079
Magnavox
081 082
Mitsubishi
083
Panasonic
084
Pioneer
085
Samsung
086
Sharp
119
Sony
087
Thomson
120
Toshiba
088
Yamaha
089
Zenith
089
10
7. Programming Your Audio Device
To program your laser disc, compact disc,
receiver / amplifier or cassette tape...
1. Turn on your Audio device - cassette deck, CD,
receiver, amplifier.
2. Press [AUDIO], then [SELECT] together - hold
both buttons down until [AUDIO] illuminates.
3 a. Press and hold [CH +] until your Audio device
turns off. As soon as your Audio device turns
off, release [CH +].
OR
b. From the Audio Setup Code list, locate and
enter a 3-digit code for your brand. If multiple
codes are listed, you may have to enter several
codes until your Audio device turns off.
4. Press [MUTE] If your Audio device turns back on,
press [AUDIO] to lock in the code. The [AUDIO]
button will blink and go out.
If your Audio device dose not turn back on, repeat
steps 3 and 4 until you can turn your Audio device
off and on❶ .
.
Write your Audio brand & setup code
To program your 2nd TV, 2nd VCR, or 2nd DVD...
1. Turn on your 2nd TV, 2nd VCR, or 2nd DVD.
2. Press [AUDIO], then [SELECT] together - hold
both buttons down until [AUDIO] illuminates.
3. Press [TV] to program a 2nd TV (or [VIDEO] for 2nd
VCR). The [AUDIO] and [TV] buttons will blink.
4. a. Press and hold [CH +] until your 2nd TV turns
off. As soon as your 2nd TV turns off, release
[CH +]
OR
b. From the TV Setup Code list, locate and enter
a 3-digit code for your brand. If multiple codes
are listed, you may have to enter several codes
until your 2nd TV turns off.
5. Press [MUTE] If your 2nd turns back on, press
[AUDIO] to lock in the code. The [AUDIO] button
will blink and go out.
If your 2nd TV does not turn back on, repeat steps
3 and 4 until you can turn your 2nd TV off and on❶ .
.
Write your 2nd TV brand & setup code
Refer to section 16 for code number readback.
❶ Note when using the Point and Press™
Programming method (step 4a). If you find a code
that turns your Audio device off but not back on (step
4), you may have gone past the correct matching
code. Try pressing [CH –] one press at a time until
you find a code that turns your Audio device back on.
11
Audio Setup Codes
1. Laser Disc
Pioneer
013 014
Proscan
029
RCA
029
Sanyo
006
Sony
025
Zenith
006
2. Compact Disc
ADC
085
Akai
017 031
Aiwa
086
Carver
086
Crown
033
Denon
036
Fisher
001 003
Goldstar(LG)
016
Harman/Kardon
041
JVC
063
Kenwood
001 015 028 065 086
Krol
086
Magnavox
002 007 019 038
Mission
086
Mitsubishi
017 070
NAD
024 046 072
Nakamichi
075 077
NEC
018
NSM
086
Onkyo
076
Panasonic
009 035
Philips
007 019 038
Pioneer
009 047 097
Quasar
035
Radio Shack
009 023 028 049 062
RCA
019 038 057
Sanyo
003 032
SAE
086
Scott
023
Sharp
021 028
Sony
050 061 071
Soundesign
004 005 027 060
STS
085
Sylvania
007
Teac
023
Technics
035 042 103
Toshiba
024
Yamaha
074
3. Receiver / Amplifier
Adcom
139
Aiwa
163 165
Akai
158
Bose
136 163
Carver
073 167
Citation
162
Denon
034 068 102
Everquest
107
Fisher
073
Fosgate Audionics
169
Goldstar(LG)
088
Harman/Kardon
043 169 170 172
12
Hitachi
Jensen
JVC
Kenwood
luxman
Marantz
NAD
Onkyo
Optimus
Panasonic
Parasound
Philips
Pioneer
Quasar
Radio Shack
Realistic
Rotel
Sansui
Sanyo
Scientific Atlanta
Scott
Sharp
Sherwood
Sony
Soundesign
SSI
Taekwang
Teac
Technics
Victor
Yamaha
Zenith
4. Cassette Tape
Aiwa
Akai
Audio Access
B&K
Denon
Dynamic Bass
Fisher
Fosgate Audionics
Haitai
Harman/Kardon
Inkel
JCPenny
JVC
Kenwood
Kloss
Lexicon
Luxman
Marantz
NAD
Nakamichi
Onkyo
Optimus
Philips DCC
Pioneer
Sansui
Sherwood
Sony
Taekwang
Teac
Technics
Technics DCC
Toshiba
Wards
Yamaha
106
126
053 145
045
110
080 114 124 131
108 120
052 105 118 147
040 115 158
104 109
155
089
058 090 081 135
104
012 040
079 137 138
140
114
044
116
055
082
012 040
008 020 059 091
048 092 093 094
134
158
054 064
095 104
053 145
030 133 171
048 088 092 093 094
153
157
161
141 142
039
087
129
168
164
051 168
164
143
056 098
042 129 160 164
143
154
111 159
125 130
121
150
066 119 146
122 123 157
026
010 032 099 113 117
149 152 166
112
022 096
157
127 150
037 144 148
026
151
129
067 100 101 132
13
8. Programming the [ ALL ] Button
Once you have programmed each of your devices,
press [ALL] to turn all of them on / off with a single
button press.
If you would like the [ALL] button to also tune
your TV to its correct output channel (typically 3)
follow these steps:
1. Press [DEVICE], then [CBL] to select the remote’s
cable mode.
2. Press [SETTINGS], then [ALL] together - hold
both buttons down until the [TV] illuminates.
3. Press [0 ], then [3 ]❶ , ❷ .
4. Press [CH+] to store the TV channel. The [TV]
button will blink and go out.
❶ Your TV output channel may also be 2 or 4.
If you are not sure, contact your cable operator.
❷ Depending on your TV brand, the channel may
have to be entered as “3”, “03” or “003”.
Note : When pressing the [ALL] button, be sure to
keep the remote control aimed at the devices to
ensure all functions are received in their entirety.
9. Programming [MOVIES], [SPORTS] [NEWS]
Each of these buttons can be programmed to store a
favorite cable channel.
For example, to program the [MOVIES] button to
cable channel 53, follow these steps:
1. Press [DEVICE], then [CBL] to select the remote’s
cable mode.
2. Press [CBL], then [MOVIES] together - hold both
down until [CBL] illuminates.
3. Press [0 ], [5 ], [3 ]. (enter ch. # in 3-digit format)❶ .
4. Press [MOVIES] to store this channel. The [CBL]
button will blink and go out.
Programming the [SPORTS] or [NEWS] buttons is
the same general procedure as above.
❶ May also be 4-digit (or 5-digit) format.
The exact # of digits you need to enter depends
on how your cable operator has setup your
cable set-top terminal.
10. Operating Your Cable Set-Top Terminal
Your remote control is designed to operate all the
features and functions of your digital cable set-top
terminal.
To operate your cable set-top terminal, press
[DEVICE], then [CBL]. In your remote’s cable
mode, you can then press...
[ALL]
[CBL]
[TV]
[VIDEO]
[AUDIO]
[CH+] / [CH–]
[VOL+] / [VOL–]
[MUTE]
[EXIT ]
[SETTINGS]
[GUIDE]
[INFO]
[FAV ]
[LAST]
[A ], [B], [C]
[0] [9]
[PAGE + –]
[ ], [ ], [ ], [ ]
[SELECT]
[BYPASS]
[TV / VCR]
[VCR / VOD]
[
]
[
]
[
]
[
]
[
]
[
]
[MOVIES]
[SPORTS]
[NEWS]
14
15
ALL devices on / off.
Cable set-top terminal on / off.
TV on /off.
VCR / DVD on / off.
Audio on / off.
Increases / decreases cable channel.
Increases / decreases cable volume.
Mute cable volume.
Exits on-screen menus, view guide,
interactive screens.
Displays program settings.
Displays interactive program guide.
Displays channel, time information.
View favorite channels.
Last channel viewed.
On-screen decision buttons.
Numeric entry buttons.
Page up / down through menus,
program guide.
Navigate on-screen menus, program
guide, PPV events and interactive
services.
Select menu, interactive screen item.
Switch between cable set-top terminal
and TV.
Changes VCR video inputs.
“Toggles” the VCR buttons between
cable Video-On-Demand (VOD) and
VCR / DVD functions.
Press [VCR / VOD]. If...
a. [CBL] illuminates, the VCR buttons
are operating your cable Video-On
-Demond(VOD) functions.
OR
b. [ VIDEO ] illuminates, the VCR
buttons are operating your VCR or
DVD functions.
While [CBL] or [VIDEO] is illuminated,
press [VCR / VOD] to switch from
Video-On-Demond to VCR or VCR to
Video-On-Demand.
VCR / DVD or VOD rewind.
VCR / DVD or VOD play.
VCR / DVD or VOD fast-forward.
VCR / DVD or VOD pause.
VCR / DVD or VOD stop.
VCR / DVD or VOD record.
Programmable favorite channel.
Programmable favorite channel.
Programmable favorite channel.
To operate your TV, press [DEVICE] , then [TV]. In
your remote’s TV mode , you can then press...
[ALL]
ALL devices on / off.
[CBL]
Cable set-top terminal on / off.
[TV]
TV on /off.
[VIDEO]
VCR / DVD on / off.
[AUDIO]
Audio on / off.
[CH +] / [CH –]
Increases / decreases TV channel.
[0] [9]
Numeric entry buttons.
[VOL+] / [VOL–]
Increases / decreases TV volume.
[MUTE]
Mute TV volume.
[TV / VCR ]
Change TV’s video inputs.
[
]
VCR / DVD rewind.
[
]
VCR / DVD play.
[
]
VCR / DVD fast-forward.
[
]
VCR / DVD pause.
[
]
VCR / DVD stop.
[
]
VCR / DVD record.
[ALL]
[CBL]
[TV]
[VIDEO]
[AUDIO]
[CH+] / [CH–]
[0] [9]
[VOL+] / [VOL–]
[MUTE ]
[TV / VCR ]
[
]
[
]
[
]
[
]
[
]
[
]
12. Operating Your Video(VCR or DVD) Device
When you first program your remote, volume /
mute are controlled through your TV(except
AUDIO which defaults to the AUDIO device).
The volume control options in each mode of the
remote are:
CBL
TV (default), Cable or Audio.
TV
TV (default), Cable or Audio.
VIDEO
TV (default), Cable or Audio.
Audio device (default), Cable or TV.
AUDIO
To control volume / mute through your cable
set-top terminal in the remote’s cable mode...
1. Press [CBL], then [SELECT] together - hold both
buttons down until [CBL] illuminates.
2.Press [VOL+], then [CBL] for cable volume. The
[CBL] button will blink and go out.
To return volume control to your TV, repeat step 1,
then press [VOL+], then [TV] in step 2.
To control volume / mute through your cable
set-top terminal in the remote’s Video mode...
1. Press [VIDEO], then [SELECT] together - hold
both bottons down until [VIDEO] illuminates.
2. Press [VOL+], then [CBL] for Cable volume. The
[VIDEO] button will blink and go out.
To return volume control to your TV, repeat step 1,
then press [VOL+], then [TV] in step 2.
11. Operating Your TV
Your remote control can operate many functions of
your TV.
Your remote control can operate many functions of
your VCR or DVD.
To operate your VCR or DVD, press [DEVICE]
then [VIDEO]. In your remote’s Video, you can
then press...
[ALL]
ALL devices on / off.
[CBL]
Cable set-top terminal on / off.
[TV]
TV on /off.
[VIDEO]
VCR / DVD on / off.
[AUDIO]
Audio on / off.
[CH+] / [CH –]
Increases / decreases VCR channel.
[0] - [9]
Enter VCR channels.
[VOL+] / [VOL–] Increases / decreases TV volume.
[MUTE]
Mute TV volume.
[TV / VCR ]
Change VCR video inputs.
[
]
VCR / DVD rewind.
[
]
VCR / DVD play.
]
[
VCR / DVD fast-forward.
[
]
VCR / DVD pause.
]
[
VCR / DVD stop.
[
]
VCR / DVD record.
13. Operating Your Audio Device
Your remote control can be setup to operate a tape
deck, CD, receiver, amplifier, 2nd TV, 2nd VCR as an
Audio device.
To operate your Audio device, press [DEVICE],
then [AUDIO]. In your remote’s Audio mode, you
can press...
16
ALL devices on / off.
Cable set-top terminal on / off.
TV on /off.
VCR / DVD on / off.
Audio on / off.
Increases / decreases channel.
Enter channels.
Increases / decreases volume.
Mute volume.
Change VCR / DVD video inputs.
Rewind.
Play.
Fast-forward.
Pause.
Stop.
Record.
14. Programming Volume Control
17
15. Your Remote’s SmartKeys TM
Your remote has three SmartKeysTM ([CBL], [TV],
[BYPASS]) that operate in its cable mode.
Each SmartkeyTM can be programmed so whenever
it’s pressed, it can transmit up to 12 individual button
presses in sequence.
Programming and using the [CBL] SmartKeyTM
The [CBL] button normally turns on / off your cable
set-top terminal.
You can program the [CBL] SmartkeyTM to turn on
your cable set-top terminal and TV, and tune your TV
to its correct output channel (typically 3) with one
button press.
1. Press [DEVICE], then [CBL] to select the remote’s
cable mode.
2. Press [CBL], then [SETTINGS] together - hold
both button down until [CBL] illuminates.
3. In this order, press [CBL], [TV], [0], [3]❶ , ❷ .
The [CBL] button will blink and remain illuminated.
4. Press [CH +] to lock in this setting. The [CBL]
button will blink and go out.
To return the [CBL] button to its normal function,
repeat steps 1 & 2, then press [CH –].
Programming and using the [TV] SmartKeyTM
The [TV] button normally turns on / off your TV.
You can program the [TV] SmartKeyTM to turn on your
TV and tune your TV to its correct output channel
(typically 3) with one button press.
1. Press [DEVICE], then [CBL] to select the remote’s
cable mode.
2.Press [TV], then [SETTINGS] together - hold both
buttons down until [TV] illuminates.
3. In this order, press [TV], [0], [3]❶ , ❷ .
The [TV] button will blink and remain illuminated.
4. Press [CH+] to lock in this setting. The [TV] button
will blink and go out.
To return the [TV] button to its normal function,
repeat setps 1 and 2 above, then press [CH –]
Programming and using the [BYPASS]
SmartKeyTM
18
The [BYPASS] button (cable mode) normally places
your Cable set-top terminal in a BYPASS mode.
While the cable set-top terminal is in its BYPASS
mode, you can record one program on your VCR
and watch a different program through your TV.
When exiting the cable set-top terminal’s BYPASS
mode, your TV must be re-tuned to its correct
output channel (typically 3) for proper cable
reception.
You can program the [BYPASS] SmartKeyTM so
automatically tune your TV to its correct output
channel.
1. Press [DEVICE], then [CBL] to select the remote’s
cable mode.
2. Press [BYPASS], then [SETTINGS] together hold both buttons down until [CBL] illuminates.
3. In this order, press [BYPASS], [DEVICE], [TV], [0],
[3]❶ , ❷ . The [CBL] button will blink and remain
illuminated.
4. Press [CH +] to store the setting. The [CBL]
button will blink and go out.
To return the [BYPASS] button to its normal function,
repeat steps 1 and 2 above, then press [CH–].
❶
Your TV output channel may also be 2 or 4. If you
are not sure, contact your cable operator.
❷
Depending on your TV brand, the channel may
have to be entered as “3”, “03” or “003”
Note : When using any SmartKeyTM to transmit a
series of functions, be sure to keep your remote
aimed at the devices to ensure all functions are
received in their entirety.
16. Code Number Readback
To identify a 3-digit setup code stored under the
Point and PressTM method, follow these steps:
To identify the TV setup code...
1. Press [TV], then [SELECT] together - hold both
buttons down until [TV] illuminates.
2. Press [INFO] The [TV] button will blink back the
code numbers, with a 1-second interval between
each digit of the code.
Example : For code “035”, the remote will blink 10
times, then 3 times, then 5 times.
To identify the 3-digit Video code, press [VIDEO],
then [SELECT] in step 1, then press [INFO] .
19
To identify the 3-digit Audio code, press [AUDIO],
then [SELECT] in step 1, then press [INFO].
Rev. 7/2001
© 2001, CONTEC CORPORATION
006
007
ate IV Model RT-U4
9C
eckM
Ch
Model
Setup Code
Motorola (General Instrument)
DL4, DP(V),
CFT2200,2100 DQN(V),
DPBB
001
003
002
DCT, CFT2200
Voyager
004
Pioneer
BC-4600,
BA-9000
BA-5000, BA-6000
009
008
Philips
BA-V1000
BA-V2000
010
Digital
017
CBL
CBL
CBL
CBL
CBL
Device
CBL
CBL
CBL
CBL
CBL
CBL
CBL
CBL
All on
All on
All on
All on
All on
All on
ALL
All on
All on
All on
All on
All on
All on
All on
All on
CABLE
TV
VIDEO
AUDIO
CBL on / off
TV on / off
Video on / off
Audio on / off
CBL on / off
TV on / off
Video on / off
Audio on / off
CBL on / off
TV on / off
Video on / off
Audio on / off
CBL on / off
TV on / off
Video on / off
Audio on / off
CBL on / off
TV on / off
Video on / off
Audio on / off
CBL on / off
TV on / off
Video on / off
Audio on / off
CBL on / off
TV on / off
Video on / off
Audio on / off
CABLE
TV
VIDEO
AUDIO
CBL on / off
TV on / off
Video on / off
Audio on / off
CBL on / off
TV on / off
Video on / off
Audio on / off
CBL on / off
TV on / off
Video on / off
Audio on / off
CBL on / off
TV on / off
Video on / off
Audio on / off
CBL on / off
TV on / off
Video on / off
Audio on / off
CBL on / off
TV on / off
Video on / off
Audio on / off
CBL on / off
TV on / off
Video on / off
Audio on / off
CBL on / off
TV on / off
Video on / off
Audio on / off
GUIDE
INFO
Guide
Info
View Guide
Info
Display
Guide
Info
Guide
Info
Guide
Info
GUIDE
INFO
Guide
Info
Display
Guide
Info
Clock
Guide
Info
Guide
info
SETTINGS
Settings
Menu
Menu
Settings
Settings
Settings
SETTINGS
Menu
Menu
Learn
Settings
Menu
Menu
Menu
Sel
Sel (Event)
Select
<
>
Cursor
Sel
<
>
OK
<
>
< >
CBL
All on
< >
CBL
ALL
< >
Device
<>
005
Explorer
(WorldGate™)
018
< >
004
Explorer
(Blue Ridge)
016
< >
Setup Code
Mfg
Explorer
(#, *)
015
< >
Select
<
>
Sel
<
>
Sel
<
>
SELECT
<
>
Select/OK
<
>
AU
Prg
Page +
Page -
Day >
< Day
Day >
< Day
Mute
Mute
Mute
Exit
Mute
Exit
Mute
Exit
MUTE
EXIT
Mute
Exit
Vol +
Vol Ch +
Ch -
Vol +
Vol Ch +
Ch -
Vol +
Vol Ch +, Power on
Ch -, Power on
Vol +
Vol Ch +
Ch -
Vol +
Vol Ch +
Ch -
Vol +
Vol Ch +
Ch -
VOL +
VOL CH +
CH -
A
B
C
PPV
Buy
Buy
A
B
C
A
B
C
A
B
C
0, 1 - 9
LAST
FAV
0, 1 - 9
Last
Fav
0, 1 - 9
Last
Fav
0, 1 - 9
Last
Fav
0, 1 - 9
Lch
Rcl
0, 1 - 9
Last
Fav
0, 1 - 9
Last
Fav
REW
PLAY
FF
PAUSE
STOP
REC
REW - Cable or Video
PLAY - Cable or Video
FF - Cable or Video
PAUSE - Cable or Video
STOP - Cable or Video
REC - Cable or Video
Back
Fwd
Pause
REW - Cable or Video
PLAY - Cable or Video
FF - Cable or Video
PAUSE - Cable or Video
STOP - Cable or Video
REC - Cable or Video
BYPASS
TV / VCR
VCR / VOD
Bypass
TV / VCR (VCR)
VCR / VOD
Bypass
TV / VCR (VCR)
VCR / VOD
TV / VCR (VCR)
VCR / VOD
TV / VCR (VCR)
VCR / VOD
Movies
Sports
News
Movies
Sports
News
Movies
Sports
News
Movies
Sports
News
Movies
Sports
News
Select
<
>
Sel
<
>
PAGE
PAGE
Page +
Page -
Day >
< Day
Sleep
MUTE
EXIT
Mute
Exit
Mute
VOL +
VOL CH +
CH -
Vol +
Vol Ch +
Ch -
A
B
C
Sel
Sel
Page +
Page -
PC / PM
TCP
Page +
Page -
Timer
Mute
Del
Mute
Del
Mute
Exit
Mute
Clr
Mute
Mute
Exit
Mute
Exit
Vol +
Vol Ch +
Ch -
Vol +
Vol Ch +
Ch -
Vol +
Vol Ch +
Ch -
Vol +
Vol Ch +
Ch -
Vol +
Vol Ch +
Ch -
Vol +
Vol Ch +
Ch -
Vol +
Vol Ch +
Ch -
Vol +
Vol Ch +
Ch -
A
B
C
A
B
C
Enter
F
Prog
Enter
F
Prog
A
B
C
Str
Auth
#
Enter
Order
Clear
Order
Help
A
B
C
0, 1 - 9
Last
Fav
0, 1 - 9
LAST
FAV
0, 1 - 9
Last
Fav
0, 1 - 9
< Ch
Fav
0, 1 - 9
< Ch
Fav
0, 1 - 9
Last
Fav
0, 1 - 9
0, 1 - 9
Last Ch
Fav Ch
0, 1 - 9
Last
Fav
0, 1 - 9
Last
Fav
REW - Cable or Video
PLAY - Cable or Video
FF - Cable or Video
PAUSE - Cable or Video
STOP - Cable or Video
REC - Cable or Video
REW - Cable or Video
PLAY - Cable or Video
FF - Cable or Video
PAUSE - Cable or Video
STOP - Cable or Video
REC - Cable or Video
REW
PLAY
FF
PAUSE
STOP
REC
REW - Cable or Video
PLAY - Cable or Video
FF - Cable or Video
PAUSE - Cable or Video
STOP - Cable or Video
REC - Cable or Video
Bypass
TV / VCR (VCR)
VCR / VOD
Bypass
TV / VCR (VCR)
VCR / VOD
Bypass
TV / VCR (VCR)
VCR / VOD
BYPASS
TV / VCR
VCR / VOD
Bypass
TV / VCR (VCR)
VCR / VOD
A/B
TV / VCR (VCR)
VCR / VOD
A/B
TV / VCR (VCR)
VCR / VOD
Bypass
TV / VCR (VCR)
VCR / VOD
C/R
TV / VCR (VCR)
VCR / VOD
A/B
TV / VCR (VCR)
VCR / VOD
A/B
TV / VCR (VCR)
VCR / VOD
P
TV / VCR (VCR)
VCR / VOD
#
Channel Memory
CH Link
WEB
MALL
CH Link
WorldGate
Channel Memory
Movies
Sports
News
PPV/Lock
Help
Music/Enter
Movies
Sports
News
Movies
Sports
News
Movies
Sports
News
Movies
Sports
News
Movies
Sports
News
Movies
Sports
News
PPV
*
PAGE
PAGE
Rcl
Page
Page
REW - Cable or Video
PLAY - Cable or Video
FF - Cable or Video
PAUSE - Cable or Video
STOP - Cable or Video
REC - Cable or Video
<>
SELECT
<
>
<>
1. Your remote is equipped with a Point and PressTM
Programming label on the back of its case. This
will help you quickly program the remote without
using codes.
2. An illuminated mode (power) button will remain
on while the remote is in a programming mode. In
the absence of an entry, the illuminated button will
go out after 45 seconds.
When locking in your devices, the illuminated
button will blink and go out,
3. When using the Point and PressTM programming
method, you may find a code that turns your
device off but not back on. If this happens...
a.the correct code has not been found. Continue
pressing [CH +] until your devices turn on and
off.
OR
b.you may have gone past the correct matching
code. Try pressing [CH –] one press at a time
until you find a code that turns your devices turn
back on.
4. If the same button is pressed and held for 45
seconds, your remote control will turn itself off.
This extends the battery life by should the remote
become lodged under or between heavy objects.
5. For diagnostic functions on Motorola (GI) DCT
and CFT2200 cable set-top terminal, press
[SELECT] + [INFO] together.
6. If you have any questions concerning the operation
of your cable set-top terminal, contact your cable
operator.
8540,70,90
< >
18. Helpful Tips and Troubleshooting
8600
< >
2. Press [SETTINGS], then [SETTINGS] again. The
[CBL] button will blink and go out.
8600x
<>
1. Press [CBL], then [SELECT] together-hold both
down until the [CBL] illuminates.
Scientific Atlanta
Explorer
<>
To reset your remote control to its factory default
settings...
Mfg
Model
< >
17. Resetting Your Remote control
Page +
Page -
Prev
PC
Next