User manual | Cortelco 1201 Telephone User Manual

Cortelco 1201 Telephone User Manual
4 SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, and injury, please follow
these basic safety precautions before you use this equipment.
1. Carefully read the instructions in this manual.
2. Follow all warnings and instructions marked on the unit.
3. When cleaning, unplug the telephone jack from the wall outlet. Use
a damp cloth. DO NOT use liquid or aerosol cleaners.
4. Do not use this equipment near water, eg: near a kitchen sink,
bathtub, washbowl, laundry rub, swimming pool or in a wet
basement.
5. Install in a protected location. Ensure all lines and cords are away
from foot traffic. DO NOT place objects on the line cord that may
cause damage or abrasion.
6. Avoid spilling any liquid on the unit. This may cause internal
shorting, fire or shock and is not covered under your warranty.
7. Do not overload wall outlets and extension cords as this can result
in the risk of fire or electrical shock.
8. Never push objects of any kind into this telephone as they can
touch dangerous voltage points or short out parts that could result
in a risk of fire or electrical shock.
9. Take the phone to a qualified technician when it requires repair
work or service. To reduce the risk of electrical shock, do not
disassemble the telephone. Opening or removing covers can
expose you to dangerous voltages or other risks. Incorrect reassembly can cause electrical shock during subsequent use.
10.Avoid using the telephone during an electrical storm. There can be
a slight risk of electrical shock from lightning.
11.DO NOT use the telephone to report a gas leak, if in the vicinity of
the leak.
12.Unplug this telephone from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
l If liquid is spilled into the unit.
l If the unit is exposed to rain or water.
l If the unit does not operate normally by following the
operating Instructions.
l If the unit is dropped or the casing is damaged.
l If the unit exhibits a distinct change in performance.
7
OWNER'S
INSTRUCTION MANUAL
MODEL 1201
3 WALL INSTALLATION
1 LOCATION OF CONTROLS
1. Slide the handset tab out and rotate it 180 degrees so that the hook
points up. This will hold the handset in the cradle when the phone is
mounted on the wall.
Hook Switch
LCD display Message lamp
Memory
(M1~M3)
2. Remove the desk stand from the phone base (see diagram 2).
3. Mount the phone on a standard telephone wall jack.
RING
Desk tab
position
M1
M2
M3
PAUSE
VOL.
STORE/SET
AUTO
MUTE
HOLD
REDIAL
VOL.
STORE/SET
AUTO
MUTE
HOLD
REDIAL
Wall mount
tab position
diagram 2
diagram 1
FLASH
FLASH
Handset
PAUSE
Volume
1
6
10. Hold button
To place a call on hold, press HOLD and hang up the handset. To retrieve the
call lift the handset or go off hook on any other phone connected to the line.
11. Pause button
Pressing this button will insert a 3 second pause in the dialing sequence. This
is intended to be used with memory dialing.
12. Phone resetting
Resetting the phone will erase all memory dial numbers and the redial
memory.
1. Lift the handset.
2. Dial *#0000*#.
3. Hang up the handset.
5
Dialing mode
switch
Flash time
switch
Ringer volume
switch
2
2 OPERATIONS
1. Dial mode switch
This switch is located on the bottom of the telephone. For Tone Dialing, set
the switch to the T position. For Pulse Dialing, set the switch to the P position.
2. Redial function
This feature allows you to redial the last phone number dialed.
a. Lift handset.
b. Press REDIAL.
3. Mute function
This feature allows you to turn off your telephone's microphone so that the
other party cannot hear you.
4. Flash button
Press FLASH instead of pressing the hook switch to activate services such as
Call Waiting or 3-Way Calling, or to activate certain PBX or Centrex features.
You may be required to press other buttons before or after you press FLASH.
Refer to the custom calling instructions provided by your local telephone
company or to the operating instructions provided with your PBX.
5. Flash time switch
The initial factory-set flash length is 600 milliseconds, which is appropriate for
most installations. However, two other Flash times are available. Use this
switch on the bottom of the phone to select 100, 300 or 600 mSec.
6. Ringer volume switch
Ringer Volume Switch - There are 3 ringer levels (HI, LO, and OFF). These may
be selected by this switch on the bottom of the telephone.
3
7. Volume setting
Press the VOL.+ or VOL.- buttons to adjust the receive volume during a
conversation. There are 4 levels.
8. One-touch memory
There are 3 memory locations (M1~M3).
A. To store a number to memory
1. Lift the handset.
2. Press STORE/SET.
3. Dial the number to be stored (Press PAUSE to insert a pause).
4. Press STORE/SET.
5. Press the desired Memory Button (M1~M3).
B. To dial a number stored in memory
1. Lift the handset.
2. Press the desired Memory Button (M1~M3).
9. Two-touch memory
There are 10 two-touch memory locations.
A. To store a number to memory
1. Lift the handset.
2. Press STORE/SET.
3. Dial the number to be stored (Press PAUSE to insert a pause).
4. Press STORE/SET.
5. Press the desired Memory Button (0~9).
B. To dial the number in memory
1. Lift the handset.
2. Press AUTO.
3. Press the desired Memory Button (0~9).
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising