Costar 9RV Carbon Monoxide Alarm User Manual

OWNER’S MANUAL
Model 9RV
Carbon Monoxide Alarm for Recreational Vehicle Use
ATTENTION: PLEASE READ, FOLLOW AND SAVE
CSA 6.19-01
Dear New COSTAR® 9RV Owner,
Congratulations as you have taken steps to help insure the health and life safety of you and your family. We are
proud to offer you our unique, patented CO Sensor technology that detects CO in a mannersimilar to the human
body’s response. The COSTAR® 9RV is an ideal and low-cost way of warning you of both the acute and chronic
effects of CO poisoning.
Please read this owner’s manual carefully so you will have a better understanding of the effects of CO poisoning and the COSTAR® 9RV Alarm, as we work together pursuing a safer, healthier indoor air quality for us all.
To your good health and safety,
Mark Goldstein, Ph.D.
President
Quantum Group Inc.
!
WARNING: Failure to replace this product by the “REPLACE BY DATE” printed on the alarm cover
may result in death by Carbon Monoxide poisoning. Replace By Date is six (6) years from date of
manufacture.
1.0 WHAT YOU SHOULD KNOW ABOUT CO
Carbon monoxide (CO) is an insidious poison. It is a colorless, odorless and tasteless gas. It is a cumulative
poison. Even low levels of CO have been shown to cause brain and other vital organ damage in unborn infants
with no effect on the mother.
The following symptoms may be related to CARBON MONOXIDE POISONING and should be discussed
with ALL members of the household:
MILD EXPOSURE:
Headaches, running nose, sore eyes, nausea, vomiting, fatigue (often described as “flu”-like symptoms);
MEDIUM EXPOSURE:
Severe throbbing headache, dizziness, drowsiness, confusion, fast heart rate;
EXTREME EXPOSURE:
Unconsciousness, convulsions, brain damage, cardio respiratory failure, death.
Many cases of reported CARBON MONOXIDE POISONING indicate that while victims are aware they are
not well, they become so disoriented they are unable to save themselves by either exiting the building or calling
for assistance. Also, young children and household pets may be the first affected. Your CO alarm is designed to
detect the toxic CO fumes that result from incomplete combustion, such as fuel burning appliances (e.g. space
heater, furnace, water heater, range, oven, clothes dryer), or other sources of combustion (e.g. kerosene-burning
stove or heater or gas log fireplace) or internal combustion engines (e.g. automobile exhaust). Furthermore,
installation of this device is not a substitute for proper installation, use, and maintenance of fuel-burning appliances, including appropriate ventilation and exhaust systems.This carbon monoxide alarming device is designed
to detect carbon monoxide gas from ANY source of combustion. It is NOT designed to detect smoke, fire, or
any other gases.
CAUTION: This alarm will only indicate the presence of carbon monoxide gas at the sensor. Carbon monoxide gas may be present in other areas.
WARNING: This product is intended for use in ordinary indoor locations of family living units. It is not
designed to measure compliance with commercial or industrial standards, such as Occupational Safety and
Health Administration (OSHA). This device is designed to protect individuals from the acute effects of carbon
monoxide exposure. It will not fully safeguard individuals with specific medical conditions. Individuals with
medical problems may consider using warning devices which provide audible and visual signals for carbon
monoxide concentrations under 30 ppm. If in doubt, consult a medical practitioner.
2.0 WHAT YOU SHOULD DO IF THE ALARM SOUNDS
!
WARNING: Actuation of your CO alarm indicates the presence of carbon
monoxide (CO), which can KILL YOU. If alarm signal sounds (flashing
RED LED and pulsating horn):
For users in the United States, follow the protocol in steps 1 through 4 below:
1) Operate reset/silence button;
2) Call your emergency services (_____ - _______) [fire department or 911];
3) Imediately move to fresh air – outdoors or by an open door or window. Do a
head count to check that all persons are accounted for. Do not reenter the premises nor move away from the open door/window until emergency services
responders have arrived, the premises have been aired out, and your alarm
remains in its normal condition.
4) After following steps 1–3, if your alarm reactivates within a 24-hour period, repeat
steps 1–3 and call a qualified repair technician (_____ - _______) to investigate
the sources of CO from fuel burning equipment and appliances, and inspect for
proper operation of this equipment. If problems are identified during this inspection, have the equipment serviced immediately. Note any combustion equipment
not inspected by the technician and consult the manufacturer’s instructions, or
contact the manufacturers directly, for more information about CO safety and this
equipment. Make sure motor vehicles are not, and have not been, operating in an
attached garage or adjacent to the residence.
For users in Canada, follow the protocol in steps 1 and 2 below:
1) Imediately move to fresh air – outdoors or by an open door or window. Check
that all persons are accounted for. Do not re-enter the premises or move away
from the open door/window until the emergency services responders have
arrived, the premises have been aired out, and your alarm remains in its normal
condition;
2) Call your emergency services (_____ - _______) [fire department or 911]; If
“service” signal sounds (RED LED flashes and horn beeps every 30 seconds),
contact the manufacturer for troubleshooting and/or instructions to return the
unit: Quantum Group, Inc. Customer Service: 1-800-432-5599
2.1 IMPORTANT CONSIDERATIONS
The 9RV has been designed and is warranted to operate for six years. Never disconnect the battery to silence
an alarm. The alarm will automatically sense when the level of CO in the air falls below the danger level. You
should stay outside the vehicle in fresh air until the alarm is silenced. When the alarm sounds, do not stand too
close to the alarm. The sound produced by the alarm is loud because it is designed to awaken a person in an
emergency. Prolonged exposure to the alarm at a close distance may be harmful to your hearing.
WARNING:TEST ALARM OPERATION AFTER VEHICLE HAS BEEN IN STORAGE, BEFORE EACH
TRIP, AND AT LEAST ONCE PER WEEK DURING USE.
3.0 DEVELOPING YOUR OWN CO SAFETY PLAN
This CO alarm can quickly alert you to the presence of CO - it cannot prevent toxic CO emissions. Please note
that there are hazards against which CO detection may not be effective, such as natural gas leaks or explosions.
The ultimate responsibility for protection against toxic CO gas rests solely on you. Installing CO alarms is just
the first step in protecting your family from toxic CO poisoning. We also suggest that you create an effective,
comprehensive safety program as outlined below.
3.1 Install CO alarms properly following the instructions in this manual.
3.2 Develop a family escape plan and practice it with your entire family, especially small children.
• Draw a floor plan of your RV and find two ways to exit. There should be one way to get out of your
RVwithout opening the door.
• Make sure that all occupants know what the CO alarm signal means and how they must be prepared to leave
the RV by themselves if necessary.
• Decide on a meeting place a safe distance from your RV and make sure all occupants understand where they
should go and wait if there is a dangerous CO condition.
• Conduct CO safety drills at least every 6 months to make sure that everyone, even small children, know
what to do in order to escape safely.
• Know where to go to call the Fire Department from outside your RV.
4.0 IMPORTANT: WHAT YOUR CO ALARM CAN AND CANNOT DO
4.1 This unit is designed to detect carbon monoxide (CO) entering its sensing chamber. It does not sense
combustible gas (such as natural gas, propane or butane), heat, smoke or flames.
4.2 NOTE: This CO alarm is designed for use within a single recreational vehicle. The alarm may not provide
early warning for occupants if it is placed outside of the recreational vehicle, such as on outside porches.
4.3 When properly located, installed, and maintained, this CO alarm is designed to provide early warning of developing poisonous CO conditions at a reasonable cost. This alarm monitors the air, and when it senses CO, it
activates its built-in alarm. It can provide precious time for you and your family to escape from your RV before
CO can seriously injure or kill. However, such an early warning is possible only if the alarm is located,
installed, and maintained as specified in the Owner’s Manual.
4.4 If your RV has an interior room divider or door it is recommended to place a CO alarm on both sides of the
divider or door. If the alarm is located outside of a bedroom, it may not wake up a sound sleeper, especially if
the bedroom door or divider is closed or only partly open.
!
WARNING: The COSTAR® Model 9RV CO Alarm is not designed for marine use.
5.0 INSTALLING THE COSTAR® 9RV ALARM FOR RECREATIONAL VEHICLE USE
Figure 1: Suggested Mounting Locations for RVs
5.1 RECOMMENDED MOUNTING LOCATIONS
One of the most important considerations in any CO alarm system is the location of the alarms. Statistics of the
National Fire Protection Association (NFPA) show that most of the fatal CO occurrences happen at night while
people are sleeping. Early warning of CO is best achieved by the correct installation of CO alarms. Placement
of an alarm in a garage may cause an alarm due to CO from engine exhaust.
5.2 Put a CO alarm in a central location inside the vehicle, near sleeping areas. A closed door can block particulate
smoke, but CO gas is likely to get through.
5.3 This CO alarm may be mounted on the wall or ceiling.
5.4 WALL LOCATION: Mount alarm at least 3 feet (usually 5-6 feet) from the floor.
5.5 CEILING LOCATION: Alarm should be mounted as close as possible to the center of a hallway or room. If
this is not possible, the edge of the alarm should be at least 4 inches from any wall.
5.6 LOCATIONS TO AVOID
• Within 5 feet (1.5m) of any cooking appliance
• Near an open window or door, because the fresh air entering the opening may delay CO from reaching the
alarm
• In damp or very humid areas or next to bathrooms with showers. Install detectors at least 5 feet (1.5 meters)
away from bathrooms
• Locations where normal ambient temperatures are not met. Normal ambient temperature limits are 40°F to
100°F (4.4°C to 37.8°C)
Note: Most batteries are not rated below -20°C or above 54°C
• Accommodation spaces should be well ventilated when household cleaning supplies or similar contaminants
are stored or used.
5.7 CONDITIONS WHICH CAN RESULT IN TEMPORARY CO SITUATIONS:
5.7.1 Excessive spillage or reverse venting of fuel burning appliances caused by:
i) Outdoor ambient conditions, such as wind direction and/or velocity, including high gusts of wind,
and insufficient draft in the vent pipes (cold/humid air with extended periods between cycles);
ii) Negative pressure differential resulting from the use of exhaust fans;
iii) Simultaneous operation of several fuel burning appliances competing for limited internal air;
iv) Loose vent pipe connections from fuel-fired appliances such as clothes dryers, furnaces, or water
heaters;
v) Obstructions, or unconventional vent pipe designs that can amplify the above situations;
vi) Poorly designed or maintained chimneys and/or vents;
5.7.2 Extended operation of unvented fuel-burning devices (range, oven, fireplace, etc.);
5.7.3 Temperature inversions that can trap exhaust gasses near the ground; and
5.7.4 RV, truck or car idling in an open or closed attached garage, or near a home.
6.0 INSTALLATION INSTRUCTIONS PLEASE READ CAREFULLY
CAUTION: THIS UNIT IS SEALED. THE COVER IS NOT REMOVABLE!
6.1 Select proper location
6.2 A mounting plate is provided on the back of the alarm. Remove the mounting plate from the back of the alarm
by holding the mounting plate and twisting the alarm in the direction indicated by the “OFF” arrow on the
alarm cover.
6.3 To insure aesthetic alignment of the alarm with the hallway or wall, the UP ARROW on the mounting plate
must be:
A) Parallel with the hallway walls when ceiling mounting
B) Pointed upward when wall mounting
C) See steps A & B in figure 2
LIMITED WARRANTY
COSTAR® Model 9RV
Step A:
Ceiling Mounting
Step B:
Wall Mounting
Step C:
Battery Installation
Step D:
Installation / Removal
Figure 2: Installation Instructions
6.4 As described in Figures 1-2, attach the mounting plate on the wall. Be sure the “UP FOR WALL MOUNTING” text and arrow are facing up. Use the screws and anchors provided to secure the mounting plate.
6.5 The battery is INSTALLED REVERSED FOR SHIPPING. Remove and reinstall the battery in the correct
orientation as noted on the inside of the battery door. When installing the battery, align the “+” and “-” battery
terminals on the correct contacts. The alarm will beep once indicating proper battery installation.
WARNING: BATTERY IS REQUIRED FOR ALARM OPERATION AND DETECTION OF CARBON
MONOXIDE. IF NO BATTERY IS INSTALLED, THE BATTERY DOOR WILL NOT CLOSE EASILY
AND THE UNIT WILL NOT ATTACH TO THE MOUNTING BRACKET.
6.6 Align marks on the edge of the trim plate with those on the alarm. Twist the alarm in the direction indicated by
the “ON” arrow on the alarm cover (see step D) until it locks in place.
6.7 To make your carbon monoxide alarm tamper resistant, a locking pin has been provided in the bag with the
screws and anchors. Using this pin will deter children and others from removing the alarm from the mounting
plate. To use the pin, insert it into the hole in the side of the alarm after the
alarm has been installed on the mounting plate (see fig. 3). Note the tamper
resist pin will have to be removed in order to change the battery. Using long
nose pliers pull the pin out of the hole, it is now possible to remove the
alarm from the mounting plate. Test alarm immediately following installation and weekly therafter for proper operation by pushing the test button
until a short beep is heard (approximately three seconds). Release the
button. The alarm will then test itself for proper operation and the RED
LED will flash 5 times. At completion of the self-test, the alarm will sound 2 patterns. The alarm then resumes
normal operation.
6.8 This box contains two self-adhesive labels. You should write the telephone numbers of the emergency service
provider and a qualified technician in the space provided in the labels. Place one label next to the alarm, and
the other label near a source of fresh air where you plan to gather after the alarm indicates the presence of
carbon monoxide.
7.0 ALARM SIGNALS
7.1 NORMAL OPERATION---RED LED flashes once every 30 seconds, indicating that the alarm is powered and
active.
7.2 ALARM CONDITION---RED LED turns “on” for 2 seconds and “off” for 4 seconds with 4 short beeps for 1
second and 5 seconds of silence. Pushing and holding the test/reset button for 3 seconds will silence the alarm
for about 4 minutes. After 4 minutes, the alarm will once again sound until the unsafe CO concentration is
reduced.
7.3 TROUBLE/SERVICE CONDITION---The detector self-tests every 10 minutes. The detector will beep and the
Indicator/Test button will flash once every 30 seconds if a fault is detected. This is an indication of a malfunction and that the detector requires immediate servicing.
7.4 LOW BATTERY---RED LED flashes and horn chirps once every 30 seconds for a minimum of (7)days.
Replace battery when this signal occurs
8.0 MAINTENANCE – CLEANING YOUR ALARM:
WARNING: Do not use any household cleaning agents, paints, varnishes or any other chemical on your 9RV
alarm.
8.1 To clean your alarm remove it from the mounting bracket as outlined in Section 6.2.
8.2 You can clean the interior of your alarm by using your vacuum cleaner hose and vacuuming throughthe openings around the perimeter of the alarm.
8.3 The outside can be wiped with a clean towel. Test your alarms weekly and repair or replace them when they no
longer function. As with any electronic product, it has a limited life. Alarms that do not work cannot warn you.
8.4 After cleaning, reinstall your alarm and test your alarm by using the TEST button.
NOTE: REGULAR TESTING IS RECOMMENDED.
9.0 BATTERY REPLACEMENT
IF TAMPER RESISTANT PIN HAS BEEN USED, REFER TO STEP 6.7 UNDER INSTALLATION
INSTRUCTIONS FOR REMOVAL INSTRUCTIONS. (see Figure 3)
9.1 To replace the battery remove the alarm from the mounting plate by rotating the alarm in the direction of the
“OFF” arrow on the cover. (see Figure 2, Step D).
9.2 The COSTAR® Model 9RV CO Alarm uses one (1) 9 volt alkaline battery. A fresh battery should last for one
year under normal operating conditions. They can be purchased anywhere batteries are sold, such as your local
hardware store.
9.3 USE ONLY THE FOLLOWING 9 VOLT BATTERY FOR CO ALARM REPLACEMENT.
Alkaline type: DURACELL MN1604
WARNING USE ONLY THE BATTERY SPECIFIED. USE OF DIFFERENT BATTERIES MAY HAVE
A DETRIMENTAL EFFECT ON THE CO ALARM. CONSTANT EXPOSURE TO HIGH OR LOW
HUMIDITY MAY REDUCE BATTERY LIFE. CHECK THE BATTERY MANUFACTURERS SPECIFICATIONS FOR PROPER OPERATING CONDITIONS.
Note: Most batteries are not rated below -20°C or above 54°C
10.0 PERIODIC ALARM TESTING
Test the alarm weekly for proper operation by pushing the test button until a short beep is heard (approximately three seconds). Release the button. The alarm will then test itself for proper operation and the RED
LED will flash 4-6 times. At completion of the self-test, the alarm will sound 2 patterns. The alarm then
resumes normal operation.
11.0 SERVICE AND WARRANTY
If after reviewing this manual you feel that your CO Alarm is defective in any way, do not tamper with the
unit. Before returning your device, call Quantum Group’s customer service line at 1-800-432-5599 to receive a
return merchandise authorization (RMA) number. Once an RMA number has been issued, return product along
a note describing the problem and send it to:
7737 Kenamar Court
San Diego, CA 92121-2425
Quantum Group Inc. offers you this limited warranty on your new carbon monoxide alarm, including all of its
component parts. This limited warranty extends solely to the original end-user purchaser of this product, provided
your purchase was made from an authorized vendor. Transfer or resale of this product will automatically terminate
warranty coverage.
Quantum Group Inc. warrants the enclosed carbon monoxide alarm to be free from defects in materials and workmanship under authorized use and service, as specified in the owner’s manual, for a period of six (6) years from
the date of manufacture. During the initial two (2) year period commencing with the date of manufacture, any
repair or replacement shall be made without charge. During the latter four (4) years of the warranty period, any
repair or replacement shall be made at a charge to the purchaser not to exceed the manufacturer’s cost of repair or
replacement. All replaced items become the property of Quantum Group Inc.
QUANTUM GROUP INC. MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, EXCEPT AS
REQUIRED BY LAW, AND IN NO CASE FOR A DURATION LONGER THAN THAT OF THIS WRITTEN
WARRANTY, EXCEPT AS REQUIRED BY LAW, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR AGAINST INFRINGEMENT,
OR ANY EXPRESS OR IMPLIED WARRANTY ARISING OUT OF TRADE USAGE OR OUT OF A COURSE
OF DEALING OR COURSE OF PERFORMANCE. Quantum Group Inc. has not authorized any other party to
extend any other warranties in connection with the sale of the product, and will not accept responsibility for any
statements, representations, or warranties made by any other person.
This limited warranty does not cover: (1) 9 volt alkaline battery; (2) products which have been improperly installed,
repaired, maintained, modified, or which have been subjected to misuse, abuse, accident, neglect, exposure to fire,
water, or excessive changes in climate or temperature, or combined with non-Quantum Group Inc.-approved accessories; (3) physical damage caused from use other than normal and proper operation or handling, as specified in the
owner’s manual; (4) cosmetic damage; (5) products on which warranty stickers or product serial numbers have been
removed, altered, or rendered illegible; (6) the cost of installation, removal or reinstallation.
QUANTUM GROUP INC. SPECIFICALLY DISCLAIMS LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT
LIMITED TO, LOSS OF PROFITS OR ANTICIPATED PROFITS ARISING OUT OF USE OF OR INABILITY
TO USE THE PRODUCT.