User`s manual | Coway CHP-03AL Water System User Manual

Water Filtration Device CHP-03AR/L/U
• This product can not be used if the voltage is different from that
mentioned in the rating plate.
• For your safety and proper use of the product, please read this
User’s Manual before use.
• Warranty card is included in this User’s Manual.
FEATURES
1. Power saving function using the light sensor
If you press the "Sleep" button, as it decreases the driving times
of the motor and the heater at night automatically, the amount of
the power consumption is decreased.
Sleep
Sleep
Sleep
Sleep
2. Booster pump for boosting the main water
(CHP-03AR)
It equipped the booster pump to show the uniform filtering
abilities in the region with the low main water pressure.
3. Low water level detecting function
It decreases the power consumption by stopping the working of
the motor and the heater when the water level in the dtorage tank
is lowered due to the water failure.
Booster
Pump
Water Level
Water Level
Water Level
4. Front draining system
It is convenient as it can drain the hot water from the front side
without moving the product when you open the front draining door.
5. Fine particles filtering system
It minimized the amount of the fine particle that can be entered into
the water tank by equpping the inno-sence filter.
1
Water Level
DEAR CUSTOMERS
Coway
FEATURES / CONTENTS
Thank you for using our Coway Water Filtration Device.
Please read this Users’ Manual to use and maintain the product correctly.
If you encounter a problem while using the product, you may solve the problem referring to
the User’s Manual. As this manual contains the product warranty card, please keep it in a safe
place. This system (CHP-03AR/L/U) conforms to NSF/ANSI 42 for aesthetic chlorine reduction and NSF/ANSI 53 for VOC reduction as verified and substantiated by test data.
This system (CHP-03AR/L) conforms to NSF/ANSI 58 for the reduction of pentavalent arsenic,
barium, cadmium, selenium, radium 226/228, trivalent chromium, hexavalent chromium, lead,
nitrate/nitrite as verified and substantiated by test data.
This system (CHP-03AR/L) registered in California.
See performance data sheet for individual contaminants and reduction performance.
This system (CHP-03AR/L) is acceptable for treatment for influent concentrations of no more
than 27 mg/L nitrate and 3 mg/L nitrite in combination measured as N and is certified for
nitrate/nitrite reduction only for water supplies with a pressure of 280 kPa(40 psi) or greater.
CONTENTS
For Information
How to Use
Safety information. . . . . . . . . . . . . . . . . . . . 3
Electricity safety. . . . . . . . . . . . . . . . . . . . . . . . 3
Installation safety. . . . . . . . . . . . . . . . . . . . . . . 4
Operation safety. . . . . . . . . . . . . . . . . . . . . . . . 5
Others. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation precautionS. . . . . . . . . . . 12
Parts name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Water filtration process. . . . . . . . . . . . . . 8
Operation / indication part. . . . . . . . . 14
How to use. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
To drink the cold water. . . . . . . . . . . . . . . . . 17
To drink the hot water . . . . . . . . . . . . . . . . . 17
To drink the room water . . . . . . . . . . . . . . . 18
MAINTENANCE
Others
INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting. . . . . . . . . . . . . . . . . . . . 27
CLEANING METHOD . . . . . . . . . . . . . . . . . . . . 21
Storage tank. . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Gutter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
SPECIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . 28
Filter replacement. . . . . . . . . . . . . . . . . . . 24
FILTER REPLACEMENT METHOD. . . . . . . . . 25
WATER FLOW DIAGRAM. . . . . . . . . . . . . . . . . 29
Performance Data Sheet . . . . . . . . . . . . 30
WARRANTY CARD. . . . . . . . . . . . . . . . . . . . . . . 39
- Please keep the User’s Manual where it can be readily reached or found -
2
Safety information
Be careful to keep this safety information.
Please read this information to prevent property loss and ensure your safety.
If not observed,
serious injury or
even death could
Danger occur.
If not observed,
serious injury or
property damage
Warning could occur.
Caution
If not observed, slight
injury or property
damage could occur.
Electricity safety
Do not use a damaged
power cord or plug, and
loose outlet.
Otherwise, electric shock or
fire may occur as a result.
Do not pull the power
cord.
Otherwise, electric shock or
fire may occur as a result.
Do not carry the unit by
its power cord.
Do not touch the power
plug with a wet hand.
Otherwise, electric shock or
fire may occur as a result.
Otherwise, electric shock or
fire may occur as a result.
Do not forcefully bend the
power cord or put it under
a heavy object to prevent
it from being damaged or
deformed.
Do not connect and
pull out the power plug
repeatedly.
Otherwise, electric shock or
fire may occur as a result.
Otherwise, electric shock or
fire may occur as a result.
If the electric outlet is wet,
carefully unplug the unit
and let the electric outlet
completely dry before
subsequent use.
Otherwise, electric shock or
fire may occur as a result.
3
Unplug the product
before repair, inspection,
or parts replacement.
Otherwise, electric shock or
fire may occur as a result.
Do not plug into an
outlet that is being used
by several other
appliances. Use an
electrical outlet dedicated.
Otherwise, electric shock or
fire may occur as a result.
For Information
Remove any dust or water
off in the pin and contacts
of the power plug.
Otherwise, fire may occur as
a result.
Do not attempt to repair
or modify the power cord
at your discretion.
Otherwise, electric shock or
fire may occur as a result.
Otherwise, electric shock or
fire may occur as a result.
In the case the power cord
is damaged, do not replace
the cord yourself. Call
Coway Service Center to
have it replaced.
Otherwise, electric shock or
fire may occur as a result.
Installation safety
A
void installing the
system in places where
the air is damp, dust is
accumulated, or water
drops.
o not install near a
D
heating device.
Otherwise, fire may occur as
a result.
D
o not place or use the
Inflammable gases, nor
the flammable materials
near the product.
therwise, electric shock or
O
fire may occur as a result.
Do not press the product
by constraint or impact.
Injury to damage to the unit
may result.
therwise, electric shock or
O
fire may occur as a result.
SAFETY INFORMATION | Electricity safety | Installation safety
When you don’t use for a
long time, close the main
water supply valve and
unplug.
Do not install the product
on a sloped floor.
Injury to the user or damage
to the unit may result.
The filtration device installation shall
comply with applicable state and local
regulations.
4
Safety information
If not observed,
serious injury or
even death could
Danger occur.
If not observed,
serious injury or
property damage
Warning could occur.
Caution
If not observed, slight
injury or property
damage could occur.
Operation safety
When the water is coming
inside of the product or
there is a puddle on the
product, call Service Center
after closing the supplying
valve and unplugging.
Otherwise, electric shock may
occur as a result.
Do not put the candle, a
light for cigarette on the
products.
Otherwise, fire may occur as
a result.
If our product produces a
strange noise or odd smell,
immediately unplug from
the electrical outlet and
call our Service Center.
Otherwise, electric shock or
fire may occur as a result.
o not place any
D
containers with water,
medicine, food, small
metallic objects, or any
flammable material on
the top of the product.
I n the case foreign material
gets inside the product,
electric shock, fire, product
damage may occur as a result.
o not allow hot water to
D
come in contact with the
human body.
Use after closing the water
tank cover completely
inside of the product.
therwise, burn may occur as a
O
result.
The buck or the foreign body
can be entered.
To drink the filtered
water, change the filter
according to the filter
replacement cycle.
When you don’t use for a
long time, use after draining
the saved water completely
and emptying the newly
room water once again.
If you use the expired filter,
the filter performance is
lowered.
5
The saved water can be
polluted.
Others
Clean after unplugging.
Otherwise, electric shock or
fire may occur as a result.
Do not clean by spraying
the water directly or don’t
wipe the product using the
benzene and thinner.
Do not repair,
disassemble,
or modify.
o not use filtered water
D
for the water exchange of
an aquarium or a fishbowl.
Otherwise, electric shock or
product damage may occur
as a result.
The room water through the
membrane isn’t suitable for
the fish’s life environment as
it removed the ionic material.
In some cases, fishes might
even die.
After moving the product
or replacing the innosense filter, the black
powder can be remained
in the inner bottom of
the water tank.
Rotate with grasping the
room water extraction
faucet or don’t raise the
product using the faucet.
It is quiet harmless as the
powder of the activated
carbon used in the
inno-sense filter was flowed
out for improving the water
tastes.
Otherwise leakage or
product damage may occur
as a result.
SAFETY INFORMATION | Operating safety | Others
Otherwise, electric shock or
fire may occur as a result.
For Information
Danger Warning Caution
Do not use with water
that is microbiologically
unsafe or of unknown
quality without
adequate disinfection
before or after the
system.
6
Parts name
Front
Front cover
Hot water safety button
Jog shuttle
Indication part
Operation part
Cold/Room water
Changeover faucet
Cup-touch lever
Front draining door
Hot water safety faucet
Gutter
Rear
Top cover
Rear cover
Power cord
Radiator
Outlet(Blue, CHP-03AR/L)
Inlet(Orange)
7
The filter is the core technology of the filtration system.
If you don’t use qualifying filter or if you use an old filter that has expired, the system
performance may degrade.
STEP 1, 2 : NEO-SENSE FILTER
This neo-sense filter has the function to reduce aesthetic chlorine, odor, volatile
organic compounds(VOC's).
STEP 3 : RO MEMBRANE FILTER
RO membrane filter has the function to reduce water contaminants such as pentavalent arsenic,
barium, cadmium, selenium, radium 226/228, trivalent chromium, hexavalent chromium, lead,
nitrate/nitrite.
STEP 4 : INNO-SENSE FILTER
This inno-sense filter has the functions to reduce smell induction material and to improve taste of
water. It also has the function to reduce aesthetic chlorine, volatile organic compounds(VOC's).
STEP 5 : CERAMIC FILTER
NEO-SENSE
FILTER
RO MEMBRANE
FILTER
INNO-SENSE
FILTER
PARTS NAME / WATER FILTRATION PROCESS
The 5-step water filtering system (CHP-03AR/L)
For Information
WATER FILTRATION PROCESS
CERAMIC
FILTER
CERAMIC
FILTER
Disposed Water Outlet
Tips
Uses of disposed water
- The daily life water should be used for cleaning the restroom, the house, clothes, or
purposes other than drinking.
- Never use the daily life water for a drinking water or a cook.
8
WATER FILTRATION PROCESS
The 6-step water filtering system (CHP-03AR/L)
STEP 1, 2 : NEO-SENSE FILTER
This neo-sense filter has the function to reduce aesthetic chlorine, odor, volatile
organic compounds(VOC's).
STEP 3 : RO MEMBRANE FILTER
RO membrane filter has the function to reduce water contaminants such as pentavalent arsenic,
barium, cadmium, selenium, radium 226/228, trivalent chromium, hexavalent chromium, lead,
nitrate/nitrite.
STEP 4 : POST-CARBON FILTER
This post-carbon filter has the functions to reduce smell induction material and to improve taste of
water. It also has the function to reduce aesthetic chlorine, volatile organic compounds(VOC's).
STEP 5 : FINE FILTER
This fine filter has the function to reduce fine particles in the water.
STEP 6 : CERAMIC FILTER
NEO-SENSE
FILTER
RO MEMBRANE
FILTER
POST-CARBON
FILTER
FINE
FILTER
CERAMIC
FILTER
CERAMIC
FILTER
Disposed Water Outlet
9
For Information
The 5-step water filtering system (CHP-03AU)
STEP 1, 2 : NEO-SENSE FILTER
This neo-sense filter has the function to reduce aesthetic chlorine, odor, volatile
organic compounds(VOC's).
WATER FILTRATION PROCESS
STEP 3 : INNO-SENSE FILTER
This inno-sense filter has the functions to reduce smell induction material and to
improve taste of water. It also has the function to reduce aesthetic chlorine, volatile
organic compounds(VOC's).
STEP 4 : UF MEMBRANE FILTER
STEP 5 : CERAMIC FILTER
NEO-SENSE
FILTER
INNO-SENSE
FILTER
UF MEMBRANE
FILTER
CERAMIC
FILTER
CERAMIC
FILTER
10
WATER FILTRATION PROCESS
The 5-step water filtering system (CHP-03AU)
STEP 1, 2 : NEO-SENSE FILTER
This neo-sense filter has the function to reduce aesthetic chlorine, odor, volatile
organic compounds(VOC's).
STEP 3 : POST-CARBON FILTER
This post-carbon filter has the functions to reduce smell induction material and to
improve taste of water. It also has the function to reduce aesthetic chlorine, volatile
organic compounds(VOC's).
STEP 4 : UF MEMBRANE FILTER
STEP 5 : CERAMIC FILTER
NEO-SENSE
FILTER
POST-CARBON
FILTER
UF MEMBRANE
FILTER
CERAMIC
FILTER
CERAMIC
FILTER
11
The summary for the proper installation of the water filtration device
1. Close main water supply valve to separate the faucet.
Do not tum the water pipe.
3. Connect the faucet with the adaptor.
Shall install the adaptor with connector on the cold water
pipe.
4. Connect 1/4 inch orange tubing with the connector
on the adaptor.
Flush water through each filter at least 5 minutes before
Connection.
WATER FILTRATION PROCESS / INSTALLATION PRECAUTIONS
2. Wind the teflon tape on the adaptor and fit it to the
pipe.
For Information
Installation precautions
5. Open the feed valve to supply water to the filtration
system.
12
Installation precautions
Please check before use!
This product is for 120 V~ 60 Hz only.
Please connect the power plug to a dedicated grounded electrical
outlet for 120 V~ 60 Hz. The water filtration device works normally
only when the electricity is connected.
• Open the main water supply valve.
The main water must be supplied to operate the water filtration device normally.
• After installing the product
Get rid of the saved water above the full water in the inner water tank 2 times or more to use.
• When the indicator in the indication part is turned off
When the indicator in the indication part is turned off, check if the power supply was stopped
due to the power failure or other cause.
• Regularly filter replacement
It is important to replace the filter regularly to drink the pure water. If the filter is overused
beyond its service life, the performance of the water filtration device deteriorate, Do not miss the
filter replacement cycle.
• When you didn’t use for a long time
If you saved the water for a long time or you didn’t use, drain the water inside of the water
filtration device completely and remove the newly filtered water one time to use.
• When you don’t want to use for a long time
Close the main water supply valve and unplug.
• Draining hot water
Slide the draining cover at the front of the product off and connect the draining hose
(continuous extraction hose) to drain the hot water in the hot water tank.
(Take care not to burn yourself when draining the hot water.)
Tips
13
When you don’t use for a long time, close the main water supply valve and unplug.
OPERATION / INDICATION PART
How to Use
Indication part/Operation part
Indication part
Power
cut
2 Hot water temperature indicator
Water
level
3 Water level indicator
5 Cold water function indicator
4 Sleep mode indicator
1 Hot water function
indicator
When you select hot water
mode, the indicator is turned
on.
3 Water level indicator
The indicator is lightened
according to the water level
of the storage tank.
 If you connect the water
filtration device, one blank is
lightened basically.
5 Cold water function
indicator
When you select cold water
function, the indicator is
turned on.
6 Cold water temperature indicator
2 Hot water temperature
indicator
The indicator is turned on according
to the hot water temperature. As
many indicators are turned on, the
hot water becomes hot more and
more.
4 Sleep mode indicator
When you select sleep mode, the
indicator is turned on.
INSTALLATION PRECAUTIONS / OPERATION/INDICATION PART
1 Hot water function
indicator
Operation part
6 Cold water
temperature indicator
The indicator is turned on according
to the cold water temperature. As
many indicators are turned on, the
cold water becomes cold more and
more.
14
OPERATION / INDICATION PART
Operation part
Water
level
▶
1 Cold water function selection button
2 Hot water function selection button
3 Sleep mode selection button
4 Light sensor
1 Cold water function
selection button
When you want to select/
deselect cold water
function, use it.
3 Sleep mode
selection button
When you wish to select/
deselect sleep mode,
use it.
15
2 Hot water function
selection button
When you want to
select/deselect Hot
water function, use it.
4 Light sensor
It is the sensor sensing
the light around the
product.
To use the hot water function
Press the hot water function selection button, check if
the hot water function indicator in the indication part is
turned on. If you want to turn off the hot water mode,
please press the selection button for several seconds.
You can drink the hot water when you turn on hot
water function and 30 minutes is passed.
OPERATION/INDICATION PART
Press the cold water function selection button and
check if cold water mode indicator in the indication
part is turned on. If you want to turn off the cold water
mode, press the selection button for several seconds.
You can drink the cold water when you turn on the
cold water function and about 1 hour is passed.
How to Use
To use the cold water function
To use the sleep mode
When you press the sleep mode selection button, as
the sleep mode indicator is turned on and the number
of the motor driving is decreased at night, the power
consumption is decreased.
When the sleep mode is operated, the cold water
become less cool.
16
HOW TO USE
To drink the cold water
Press the cold water selection button and check the lightening status in the
cold water function indicator.
Turn the jog shuttle to the left in the cold water/room
water changeover faucet and push the cup-touch lever.
▶
Tips
If the cold water doesn’t come from the water filtration device, check if the cold water
mode indicator in the indication part is turned on (See P.16).
To drink the hot water
Press the hot water selection button and check the lightening status in the
hot water function indicator.
Press the hot water safety button and push the
cup-touch lever.
Hot water
safety
button
(PUSH)
▶
Tips
17
▶
If the hot water doesn’t come from the water filtration device, check if the hot water
mode indicator in the indication part is turned on (See P.16).
How to Use
To drink the room water
Turn the jog shuttle to the right in the cold water/room water changeover faucet and push the cup-touch lever.
HOW TO USE | To drink the cold water | To drink the hot water | To drink the room water
▶
18
INSTALLATION
Follow the instruction for installation
Main water
supply valve
2 cooling stopper
120 V~ 60 Hz Only
Connect the orange color inlet tubing 1 to the
tap water supplying pipe. Connecting the outlet
tubing 2 .
Inlet tubing(Orange)
Outlet tubing
(Blue, CHP-03AR/L)
19
2
1
Maintenance
Be cautious!
Water filtration device installation place 1
Please install the water filtration system not at a rough place, a damp
place, a place where the unit is exposed to the direct sunlight, a place
where dust is present, or a place that the water drops.
INSTALLATION
Water filtration device installation place 2
Please install at the place where it is 10 cm or more off from the wall
and the bottom is flat and firm.
After installing the water filtration system
Get rid of the filtered water above the fulled water 2 times or more
necessarily after installing.
Cold water plumbing
Please connect to the cold water pipe necessarily.
(If you connect to the warm water pipe, the filter can be damaged.)
Movement and installation
When the position is moved, connect the power cord when 30 minutes
passes after installing.
Tips
Hot water X
After 30
minutes
To maintain optimal product performance, consult a Coway engineer for the detailed
installation methods.
There may be some water remaining inside of the filter which was used to test the
product during inspection process at the factory.
Please feel at easy and use as it isn’t the used product.
Don’t reuse the main water supply valve and hose that was previously used when
you install the product.
20
CLEANINGMETHOD
Storage tank
1. Turn off by pressing cold water/hot water mode
selection button in the front of the product for
2~3 seconds or more and unplug the power
cord. Close the main water supply valve.
2. Drain the water inside of the water filtration device completely
using the draining hose and the cold water/room water changeover faucet.
Please drain the water in the cold water/room water tank
from the cold water/room water extraction faucet and drain
the water in the hot water tank from the front drain hole. (See P.13 for the hot water draining method)
3. Open the upper cover of the product and open the storage tank cover.
21
6.Use the storage tank after cleaning it with the taken water, draining
completely using the draining hose, and emptying the newly filtered water
one time or more.
CLEANING METHOD | Storage tank
5.Please wipe the surface of the storage tank with
soft clothes.
Maintenance
4. Shake and clean a ceramic filter in the taken water by rotating and
separating it from the cold water/room water separation membrane.
7. Close the storage tank cover after rotating and equipping the ceramic filter
in the cold water/room water separation membrane.
22
CLEANING METHOD
8. Open the main water supply valve after closing
the upper cover and plugging the power cord.
Please operate the water filtration device
again by pressing cold water/hot water mode
selection button in the front of the product after
checking if the water is coming from the cold
water/room water extraction faucet and the hot
water extraction faucet.
Gutter
1. Gutter separation method
If you pull the front part of the gutter, it is separated
easily.
2. Gutter assembling method
You just push the hook of the gutter slightly after
sticking to the product.
Tips
23
Close the storage tank cover completely.
A worm or a foreign body can be entered.
When you clean the storage tank, don’t use the medicine or the
detergent.
If you don’t clean the medicine or the detergent cleanly, it can be
harmful to the body.
- Keep the surroundings cleanly and clean the storage tank once
per two months.
Filter
The life of the water filtration system is the filter. It isn’t the legitimated
filter or you use too long even if it is the legitimated filter, the filter
performance can be lowered.
Please change to the legitimated filter according to the replacement cycle.
If the filter is not regularly replaced, it may degrade the water quality from the product. The filter replacement cycle depending on the main water quality can be shortened rater than the expected replacement cycle.
The period for the filter exchange is made based on 10 L use in a day for house use(4 people based) and 20 L use for business.
CHP-03AR
Part No.
Names of Filter
WJNF11
Neo-sense filter
Usable Period
6 months
WJMF11-50
RO Membrane filter (CHP-03AR)
24 months
WJMF11-30-S
RO Membrane filter (CHP-03AL)
24 months
WJIF11
/ WJCF11-POST
Inno-sense filter
/ Post-carbon filter
18 months
WJFF 7
Fine filter
18 months
WJCC-02
Ceramic filter
12 months
Part No.
Names of Filter
Usable Period
WJNF11
Neo-sense filter
6 months
WJIF11
/ WJCF11-POST
Inno-sense filter
/ Post-carbon filter
18 months
WJMF11-UF
Uf membrane filter
12 months
WJCC-02
Ceramic filter
12 months
CHP-03AU
CLEANING METHOD | Gutter / FILTER REPLACEMENT
Filter replacement cycle
Maintenance
Filter replacement
About filter replacement cycle
The filter replacement cycle described above is not the filter quality
warranty period but the expected cycle (life) that the filter shows its original
performance.
Therefore, the filter replacement cycle may be reduced for the area with the
poor water quality or more application.
24
FILTER REPLACEMENT METHOD
1. Close the main water supply valve after unplugging the power cord, and
drain the water inside of the water filtration device (See P.21).
2. Remove the gutter, and separate the front cover by pressing down, and
unplug and separate all the cables connected completely.
(If the water in the storage tank remains, close the cold water/room water
changeover faucet using the stopper inside of the upper cover
and separate the front cover.)
1
2
3
5
4
25
By changing the filter and connecting the fitting and the hose precisely, check that
there is no leakage and drain the first filtered water necessarily.
FILTER REPLACEMENT METHOD
Tips
Maintenance
3. After separating the fitting connected to the filter trying to replace, please
replace the filter. (Separate the fitting using the proper tool.)
4. After connecting all the separated cables, fit a groove in the front cover and
close with pressing it down.
Tips
Please be sure to use the new filter after cleansing.
- Neo-sense filter: Please assemble after cleansing with Neo-sense filter for about
30 seconds.
- Post carbon/Fine/Inno-sense/Membrane filter (RO): Please assemble after cleansing with the main water passed Neo-sense filter for
about 3 minutes.
26
TROUBLESHOOTING
The water filtration device may operate abnormally due to minor causes not because of the
product malfunction but because of the fact that the user is not familiar with the product use.
In such a case, problems can be solved easily even without the help from the Service Center by
checking the following items. If you can’t solve the problem after checking the following items,
please call the Service Center.
Symptom
The water tastes
weird.
The water doesn’t
come.
The water is
flowing slower.
The cold water
doesn’t come.
Check
Measures to take
• Did you clean the storage tank?
Clean the storage tank.
• You didn’t use the water filtration device
for a long time.
Get rid of the saved water and clean the
storage tank.
• Isn’t it about time to change the filter?
Request the filter replacement.
• Is the water supply cut or isn’t the water
supply valve closed?
Open the main water supply valve.
• Did you miss the filter replacement times? Request the filter replacement.
• Isn’t it about time to change the filter?
Request the filter replacement.
• Is the power connected?
Check if the power cord plug in 120 V~ 60
Hz outlet.
• Didn’t you close the main water supply
valve?
Open the main water supply valve.
• Didn’t the temperature of the main water
drop suddenly?
If the water temperature is lowered, the
water amount is decreased.
• Was the cold water mode indicator
lightened?
Please press the cold water mode selection
button.
• Didn’t you close the main water supply
valve?
If it is the low water level to protect the
electric motor, the cooling function doesn’t
operate. Open the main water supply valve.
• Isn’t the back side of the water filtration
device and the wall too close?
Please keep the distance between the back
of the water filtration device and the wall to
10 cm or more.
• Is the main water being supplied actively? Check the main water supply valve.
All operation was
stopped suddenly
when driving.
27
• Is the power connected?
Check if the power cord plug in 120 V~ 60
Hz outlet.
• Isn’t water overflowing or leaking?
Request A/S.
Specification
Model
Water Filtration Device
CHP-03AR
Filtration Method
CHP-03AL
RO(Reverse Osmosis)
Power Supply
UF
120 V~ 60 Hz
Room Water
6.59 L
Cold Water
3.61 L
Hot Water
1.2 L
Total
11.4 L
Dimension
344 mm(W) × 540 mm(D) × 525 mm(H)
Working Temperature
5 °C - 35 °C
Production Rate
190 L/d (25 °C, 414 kPa)
113 L/d (25 °C, 138 kPa)
1 500 L/d (25 °C, 108 kPa)
Working Pressure
69 kPa – 827 kPa
138 kPa – 827 kPa
69 kPa – 827 kPa
22.3 kg
19.8 kg
19.8 kg
Net Weight
TROUBLESHOOTING / SPECIFICATION
Tank
Capacity
CHP-03AU
Others
Product
• The water amount can be differentiated according to the water pressure and the water
temperature.
• The water tank capacity is the amount by the size and can be different from the extraction
capacity.
• Without any prior notice, all or parts of the product are subject to change for the purpose of
improving the performance of the product.
• Refer to performance data sheet for individual contaminants, reduction performance and general
operating information.
28
WATER FLOW DIAGRAM
CHP-03AR
CHP-03AL
CHP-03AU
29
• A post carbon filter may be installed instead of an inno-sense filter. For the precise specifications of your product, refer to the data plate on the product.
Water Filtration System Performance Data Sheet
Brand: Mach
Model: CHP-03AR
Average
Influent
(mg/L)
0.05
10
25pCi/L
0.031
0.358
0.367
0.153
29.6
0.117
741.5
Average
Effluent
(mg/L)
0.006
1.4
5pCi/L
0.002
0.023
0.028
0.005
4.8
0.003
27.7
Minimum
Percent
Reduction (%)
79.1
83.5
N/A
89.0
93.8
93.8
93.6
78.5
96.0
95.7
Average
Percent
Reduction (%)
87.7
86.6
N/A
92.7
95.1
95.7
95.1
83.7
97.8
96.3
INNOSENSE
≥ 50%
2.07
0.56
54.53
72.8
POST CARBON
≥ 50%
1.96
0.53
55.0
72.8
Arsenic (Pentavalant)
Barium
Radium 226/228
Cadmium
Chromium (Hexavalent)
Chromium (Trivalent)
Lead
Nitrate/Nitrite
Selenium
TDS
Aesthetic Chlorine
VOC*
INNOSENSE
≥ 95% reduction
0.32
0.0077
95.70
97.6
POST CARBON
≥ 95% reduction
0.298
0.005
96.0
98.3
While testing was performed under laboratory conditions, actual performance may vary.
General Operating Information:
INNO SENSE FILTER
Rated Capacity
POST-CARBON FILTER
Min-Max operating pressure:
Min-Max feed water temperature:
Rated Service Flow
Daily Water Production Rate
Product Efficiency Rating
Electrical Requirements:
229 gallons (for VOC)
6,103 gallons (for Aesthetic Chlorine)
212 gallons (for VOC)
1,179 gallons (for Aesthetic Chlorine)
10 ~ 120 psi (0.7 ~ 8.4 kgf/cm2)
41 ~ 95 ºF (5 ~ 35 ºC)
0.07 GPM (for VOC)
0.5 GPM (for Aesthetic Chlorine)
82.3 GPD
39.2 %
120 Vac / 60Hz
WATER FLOW DIAGRAM / PERFORMANCE DATA SHEET | CHP-03AR
Max. Allowable
Concentration
(mg/L)
0.010
2.0
5pCi/L
0.005
0.1
0.1
0.010
10
0.05
<187.5
Substance
Others
This system has been tested and certified by the Water Quality Association according to NSF/ANSI 42, 53, and 58 for
the reduction of the substances listed below. The concentration of the indicated substances in water entering the
system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as
specified in NSF/ANSI 42, 53, and 58.
• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection
before or after the system.
• Refer to the owners manual for specific installation instructions, manufacturer’s limited warranty, user
responsibility, and parts and service availability.
• The influent water to the system shall include the following characteristics:
o
o
o
o
o
o
o
No organic solvents
Chlorine: < 2 ppm
pH: 7 - 8
Temperature: 41 ~ 95 ºF (5 ~ 35 ºC)
Iron: < 2 ppm
Turbidity: < 1 NTU
Hardness: < 1000 mg/L
30
• For parts and service availability, please contact your local dealer or Coway.
• This system is acceptable for treatment of influent concentrations of no more than 27 mg/L nitrate and 3 mg/L
nitrite in combination measured as N and is certified for nitrate/nitrite reduction only for water supplies with a
pressure of 2.8 kgf/cm2 (40 psi) or greater.
• A nitrate/nitrite sampling kit should be used to monitor the nitrate/nitrite levels in your product drinking water
at least every six months. Kits maybe purchased from your local dealer or Coway.
• This system has been tested for the treatment of water containing pentavalent arsenic (also know as As(V),
As(+5), or arsenate) at concentrations of 0.050 mg/L or less. This system reduces pentavalent arsenic, but
may not remove other forms of arsenic. This system is to be used on water supplies containing a detectable
free chlorine residual at the system inlet or on water supplies that have been demonstrated to contain only
pentavalent arsenic. Treatment with chloramines (combined chlorine) is not sufficient to ensure complete
conversion of trivalent arsenic to pentavalent arsenic. Please see the Arsenic Facts section of this Performance
Data Sheet for further information.
• Efficiency rating means the percentage of the influent water to the system that is available to the user as reverse
osmosis treated water under operating conditions that approximate typical daily usage.
• The product water should be tested every 6 months to ensure that the contaminants are being reduced
effectively. Please contact your local dealer or Coway to initiate this service.
• This reverse osmosis system contains a replaceable treatment components, critical for the effective reduction of
total dissolved solids and that product water shall be tested periodically to verify that the system is performing
properly. Replacement of reverse osmosis component should be with one of identical specifications, as defined
by the manufacturer, to assure the same efficiency and contaminant reduction performance.
• The estimated replacement time of filter, which is a consumable part, is not an indication of quality guarantee
period, but it means the ideal time of filter replacement. Accordingly, the estimated time of filter replacement
may be shortened in case it is used in an area of poor water quality.
Model of Filter
Type
Usable period (months)
WJNF11
NEO SENSE FILTER
6
COST US $
44.00
WJMF11-50
RO MEMBRANE FILTER
24
140.00
WJIF11
/ WJCF11-POST
INNO SENSE FILTER
/ POST-CARBON FILTER
18
31.00
WJFF7
FINE FILTER
18
26.00
WJCC-02
CERAMIC FILTER
12
11.00
ARSENIC FACTS
31
Arsenic (abbreviated As) is found naturally in some well water. Arsenic in water has no color, taste or odor. It must
be measured by a lab test. Public water utilities must have their water tested for arsenic. You can get the results
from your water utility. If you have your own well, you can have the water tested. The local health department
or the state environmental health agency can provide a list of certified labs. The cost is typically $15 to $30.
Information about arsenic in water can be found on the Internet at the US Environmental Protection Agency
website:
www.epa.gov/safewater/arsenic.html
There are two forms of arsenic: pentavalent arsenic (also called As(V), As(+5), and arsenate) and trivalent arsenic
(also called As(III), As(+3), and arsenite). In well water, arsenic may be pentavalent, trivalent, or a combination of
both. Special sampling procedures are needed for a lab to determine what type and how much of each type of
arsenic is in the water. Check with the labs in your area to see if they can provide this type of service.
Reverse osmosis (RO) water treatment systems do not remove trivalent arsenic from water very well. RO systems
are very effective at removing pentavalent arsenic. A free chlorine residual will rapidly convert trivalent arsenic
to pentavalent arsenic. Other water treatment chemicals such as ozone and potassium permanganate will also
change trivalent arsenic to pentavalent arsenic. A combined chlorine residual (also called chloramine) may not
convert all the trivalent arsenic. If you get your water from a public water utility, contact the utility to find out if free
chlorine or combined chlorine is used in the water system.
The CHP-03AR system is designed to remove pentavalent arsenic. It will not convert trivalent arsenic to pentavalent
arsenic. The system was tested in a lab. Under those conditions, the system reduced 0.050 mg/L pentavalent
arsenic to 0.010 mg/L (ppm) (the USEPA standard for drinking water) or less. The performance of the system may be
different at your installation. Have the treated water tested for arsenic to check if the system is working properly.
The RO component of the CHP-03AR system must be replaced every 24 months to ensure the system will
State of California
Department of Public Health
Water Treatment Device
Certificate Number
08 - 1867
WJNF11 Neo-Sense Filter
WJMF11-50 RO Membrane Filter
WJCF11-POST Post-carbon Filter
WJFF7 Fine Filter
WJCC-02 Ceramic Filter
Manufacturer: Woongjin Coway Co LTD
The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section
116830 of the Health and Safety Code for the following health related contaminants:
Microbiological Contaminants and Turbidity
None
Inorganic/Radiological Contaminants
Arsenic (Pentavalent)1
Barium
Cadmium
Chromium (Hexavalent)
Chromium (Trivalent)
Lead
Nitrate/Nitrite2
Radium 226/228
Selenium
Organic Contaminants
VOCs
Alachlor
Atrazine
Benzene
Carbofuran
Carbon Tetrachloride
Chlorobenzene
Chloropicrin
2,4-D
DBCP
o-Dichlorobenzene
p-Dichlorobenzene
1,2-Dichloroethane
1,1-Dichloroethylene
cis-1,2-Dichloroethylene
trans-1,2-Dichloroethylene
1,2-Dichloropropane
cis-1,3-Dichloropropylene
Dinoseb
Endrin
Ethylbenzene
EDB
Haloacetonitriles (HAN)
Bromochloroacetonitrile
Dibromoacetonitrile
Dichloroacetonitrile
Trichloroacetonitrile
Haloketones (HK)
1,1-Dichloro-2-Propanone
1,1,1-Trichloro-2-Propanone
Heptachlor
Heptachlor Epoxide
Hexachlorobutadiene
Hexachlorocyclopentadiene
Lindane
Methoxychlor
Pentachlorophenol
Rated Service Capacity: 229 gal
Simazine
Styrene
1,1,2,2-Tetrachloroethane
Tetrachloroethylene
Toluene
2,4,5-TP (Silvex)
Tribromoacetic Acid
1,2,4-Trichlorobenzene
1,1,1-Trichloroethane
1,1,2-Trichloroethane
Trichloroethylene
Trihalomethanes (THMs)
Bromodichloromethane
Bromoform
Chloroform
Chlorodibromomethane
Xylenes
PERFORMANCE DATA SHEET | CHP-03AR
Replacement Element(s)
Mach CHP-03AR
Others
Date Issued: June 24, 2008
Trademark/Model Designation
Rated Service Flow: 0.07 gpm
Do not use with water that is microbiologically unsafe or of unknown quality, without adequate disinfection
before or after the system.
Claims for arsenic reduction shall only be made on water supplies maintaining detectable residual free chlorine at the
reverse osmosis (RO) system inlet. Water systems using an in-line chlorinator should provide a minimum of 1minute
chlorine contact time before the RO system.
1
This system is acceptable for treatment of influent concentrations of no more than 27 mg/L nitrate and 3 mg/L nitrite in
combination measured as N and is certified for nitrate/nitrite reduction only for water supplies with a pressure of 280 kPa
(40 psig) or greater. A sampling and analysis test kit for nitrate is provided for checking the performance of this system.
Frequent analysis is encouraged.
2
32
Water Filtration System Performance Data Sheet
Brand: Mach
Model: CHP-03AL
This system has been tested and certified by the Water Quality Association according to NSF/ANSI 42, 53, and 58 for
the reduction of the substances listed below. The concentration of the indicated substances in water entering the
system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as
specified in NSF/ANSI 42, 53, and 58.
Substance
Arsenic (Pentavalant)
Barium
Radium 226/228
Cadmium
Chromium (Hexavalent)
Chromium (Trivalent)
Lead
Nitrate/Nitrite
Selenium
TDS
Aesthetic Chlorine
INNOSENSE
POST CARBON
VOC*
INNOSENSE
POST CARBON
Max. Allowable
Concentration
(mg/L)
0.010
2.0
5pCi/L
0.005
0.1
0.1
0.010
10
0.05
<187.5
Average
Influent
(mg/L)
0.05
10
25pCi/L
0.031
0.358
0.367
0.153
29.6
0.117
741.5
Average
Effluent
(mg/L)
0.006
1.4
5pCi/L
0.002
0.023
0.028
0.005
4.8
0.003
57.8
Minimum
Percent
Reduction (%)
79.1
83.5
N/A
89.0
93.8
93.8
93.6
78.5
96.0
91.5
Average
Percent
Reduction (%)
87.7
86.6
N/A
92.7
95.1
95.7
95.1
83.7
97.8
92.2
≥ 50%
≥ 50%
2.07
1.96
0.56
0.53
54.53
55.0
72.8
72.8
≥ 95% reduction
≥ 95% reduction
0.32
0.298
0.0077
0.005
95.70
96.0
97.6
98.3
While testing was performed under laboratory conditions, actual performance may vary.
General Operating Information:
INNO SENSE FILTER
229 gallons (for VOC)
6,103 gallons (for Aesthetic Chlorine)
POST-CARBON FILTER
212 gallons (for VOC)
1,179 gallons (for Aesthetic Chlorine)
Rated Capacity
Min-Max operating pressure:
Min-Max feed water temperature:
Rated Service Flow
Daily Water Production Rate
Product Efficiency Rating
Electrical Requirements:
20 ~ 120 psi (1.4 ~ 8.4 kgf/cm2)
41 ~ 95 ºF (5 ~ 35 ºC)
0.07 GPM (for VOC)
0.5 GPM (for Aesthetic Chlorine)
43.7 GPD
29.5 %
120 Vac / 60Hz
• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection
before or after the system.
• Refer to the owners manual for specific installation instructions, manufacturer’s limited warranty, user
responsibility, and parts and service availability.
• The influent water to the system shall include the following characteristics:
33
o
o
o
o
o
o
o
No organic solvents
Chlorine: < 2 ppm
pH: 7 - 8
Temperature: 41 ~ 95 ºF (5 ~ 35 ºC)
Iron: < 2 ppm
Turbidity: < 1 NTU
Hardness: < 1000 mg/L
Type
Usable period (months)
WJNF11
NEO-SENSE FILTER
6
COST US $
44.00
WJMF11-30-S
RO MEMBRANE FILTER
24
131.00
WJIF11
/ WJCF11-POST
INNO SENSE FILTER
/ POST-CARBON FILTER
18
31.00
WJFF 7
FINE FILTER
18
26.00
WJCC-02
CERAMIC FILTER
12
11.00
PERFORMANCE DATA SHEET | CHP-03AL
Model of Filter
Others
• For parts and service availability, please contact your local dealer or Coway.
• This system is acceptable for treatment of influent concentrations of no more than 27 mg/L nitrate and 3 mg/L
nitrite in combination measured as N and is certified for nitrate/nitrite reduction only for water supplies with a
pressure of 2.8 kgf/cm2 (40 psi) or greater.
• A nitrate/nitrite sampling kit should be used to monitor the nitrate/nitrite levels in your product drinking water
at least every six months. Kits maybe purchased from your local dealer or Coway.
• This system has been tested for the treatment of water containing pentavalent arsenic (also know as As(V),
As(+5), or arsenate) at concentrations of 0.050 mg/L or less. This system reduces pentavalent arsenic, but
may not remove other forms of arsenic. This system is to be used on water supplies containing a detectable
free chlorine residual at the system inlet or on water supplies that have been demonstrated to contain only
pentavalent arsenic. Treatment with chloramines (combined chlorine) is not sufficient to ensure complete
conversion of trivalent arsenic to pentavalent arsenic. Please see the Arsenic Facts section of this Performance
Data Sheet for further information.
• Efficiency rating means the percentage of the influent water to the system that is available to the user as reverse
osmosis treated water under operating conditions that approximate typical daily usage.
• The product water should be tested every 6 months to ensure that the contaminants are being reduced
effectively. Please contact your local dealer or Coway to initiate this service.
• This reverse osmosis system contains a replaceable treatment components, critical for the effective reduction of
total dissolved solids and that product water shall be tested periodically to verify that the system is performing
properly. Replacement of reverse osmosis component should be with one of identical specifications, as defined
by the manufacturer, to assure the same efficiency and contaminant reduction performance.
• The estimated replacement time of filter, which is a consumable part, is not an indication of quality guarantee
period, but it means the ideal time of filter replacement. Accordingly, the estimated time of filter replacement
may be shortened in case it is used in an area of poor water quality.
ARSENIC FACTS
Arsenic (abbreviated As) is found naturally in some well water. Arsenic in water has no color, taste or odor. It must
be measured by a lab test. Public water utilities must have their water tested for arsenic. You can get the results
from your water utility. If you have your own well, you can have the water tested. The local health department
or the state environmental health agency can provide a list of certified labs. The cost is typically $15 to $30.
Information about arsenic in water can be found on the Internet at the US Environmental Protection Agency
website: www.epa.gov/safewater/arsenic.html
There are two forms of arsenic: pentavalent arsenic (also called As(V), As(+5), and arsenate) and trivalent arsenic
(also called As(III), As(+3), and arsenite). In well water, arsenic may be pentavalent, trivalent, or a combination of
both. Special sampling procedures are needed for a lab to determine what type and how much of each type of
arsenic is in the water. Check with the labs in your area to see if they can provide this type of service.
Reverse osmosis (RO) water treatment systems do not remove trivalent arsenic from water very well. RO systems
are very effective at removing pentavalent arsenic. A free chlorine residual will rapidly convert trivalent arsenic
to pentavalent arsenic. Other water treatment chemicals such as ozone and potassium permanganate will also
change trivalent arsenic to pentavalent arsenic. A combined chlorine residual (also called chloramine) may not
convert all the trivalent arsenic. If you get your water from a public water utility, contact the utility to find out if free
chlorine or combined chlorine is used in the water system.
The CHP-03AL system is designed to remove pentavalent arsenic. It will not convert trivalent arsenic to pentavalent
arsenic. The system was tested in a lab. Under those conditions, the system reduced 0.050 mg/L pentavalent
arsenic to 0.010 mg/L (ppm) (the USEPA standard for drinking water) or less. The performance of the system may be
different at your installation. Have the treated water tested for arsenic to check if the system is working properly.
The RO component of the CHP-03AL system must be replaced every 24 months to ensure the system will
continue to remove pentavalent arsenic. The component identification and locations where you can purchase the
component are listed in the installation/operation manual.
34
State of California
Department of Public Health
Water Treatment Device
Certificate Number
08 - 1866
Date Issued: June 24, 2008
Trademark/Model Designation
Replacement Element(s)
Mach CHP-03AL
WJNF11 Neo-Sense Filter
WJMF11S-30 RO Membrane Filter
WJCF11-POST Post-carbon Filter
WJFF7 Fine Filter
WJCC-02 Ceramic Filter
Manufacturer: Woongjin Coway Co LTD
The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section
116830 of the Health and Safety Code for the following health related contaminants:
Microbiological Contaminants and Turbidity
None
Inorganic/Radiological Contaminants
Arsenic (Pentavalent)1
Barium
Cadmium
Chromium (Hexavalent)
Chromium (Trivalent)
Lead
Nitrate/Nitrite2
Radium 226/228
Selenium
Organic Contaminants
VOCs
Alachlor
Atrazine
Benzene
Carbofuran
Carbon Tetrachloride
Chlorobenzene
Chloropicrin
2,4-D
DBCP
o-Dichlorobenzene
p-Dichlorobenzene
1,2-Dichloroethane
1,1-Dichloroethylene
cis-1,2-Dichloroethylene
trans-1,2-Dichloroethylene
1,2-Dichloropropane
cis-1,3-Dichloropropylene
Dinoseb
Rated Service Capacity: 229 gal
Endrin
Ethylbenzene
EDB
Haloacetonitriles (HAN)
Bromochloroacetonitrile
Dibromoacetonitrile
Dichloroacetonitrile
Trichloroacetonitrile
Haloketones (HK)
1,1-Dichloro-2-Propanone
1,1,1-Trichloro-2-Propanone
Heptachlor
Heptachlor Epoxide
Hexachlorobutadiene
Hexachlorocyclopentadiene
Lindane
Methoxychlor
Pentachlorophenol
Simazine
Styrene
1,1,2,2-Tetrachloroethane
Tetrachloroethylene
Toluene
2,4,5-TP (Silvex)
Tribromoacetic Acid
1,2,4-Trichlorobenzene
1,1,1-Trichloroethane
1,1,2-Trichloroethane
Trichloroethylene
Trihalomethanes (THMs)
Bromodichloromethane
Bromoform
Chloroform
Chlorodibromomethane
Xylenes
Rated Service Flow: 0.07 gpm
Do not use with water that is microbiologically unsafe or of unknown quality, without adequate disinfection
before or after the system.
Claims for arsenic reduction shall only be made on water supplies maintaining detectable residual free chlorine at the
reverse osmosis (RO) system inlet. Water systems using an in-line chlorinator should provide a minimum of 1minute
chlorine contact time before the RO system.
1
This system is acceptable for treatment of influent concentrations of no more than 27 mg/L nitrate and 3 mg/L nitrite in
combination measured as N and is certified for nitrate/nitrite reduction only for water supplies with a pressure of 280 kPa
(40 psig) or greater. A sampling and analysis test kit for nitrate is provided for checking the performance of this system.
Frequent analysis is encouraged.
2
35
Water Filtration System Performance Data Sheet
Brand: Mach
Model: CHP-03AU
Average Influent Average Effluent
(mg/L)
(mg/L)
Minimum
Percent
Reduction (%)
Average Percent
Reduction (%)
Aesthetic
Chlorine
INNOSENSE
≥ 50%
2.07
0.56
54.53
72.8
POST CARBON
≥ 50%
1.96
0.53
55.0
72.8
VOC*
INNOSENSE
≥ 95% reduction
0.32
0.0077
95.70
97.6
POST CARBON
≥ 95% reduction
0.298
0.005
96.0
98.3
While testing was performed under laboratory conditions, actual performance may vary.
General Operating Information:
INNO SENSE FILTER
229 gallons (for VOC)
6,103 gallons (for Aesthetic Chlorine)
POST-CARBON FILTER
212 gallons (for VOC)
1,179 gallons (for Aesthetic Chlorine)
Rated Capacity
PERFORMANCE DATA SHEET | CHP-03AU
Max. Allowable
Concentration
(mg/L)
Substance
Others
This system has been tested and certified by the Water Quality Association according to NSF/ANSI 42, and 53 for
the reduction of the substances listed below. The concentration of the indicated substances in water entering the
system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as
specified in NSF/ANSI 42 and 53.
10 ~ 120 psi (0.7 ~ 8.4 kgf/cm2)
Min-Max operating pressure:
Min-Max feed water temperature:
41 ~ 95 ºF (5 ~ 35 ºC)
0.07 GPM (for VOC)
0.5 GPM (for Aesthetic Chlorine)
Rated Service Flow
Electrical Requirements:
120 Vac / 60Hz
• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection
before or after the system.
• Refer to the owners manual for specific installation instructions, manufacturer’s limited warranty, user
responsibility, and parts and service availability.
• For parts and service availability, please contact your local dealer or Coway.
Model of Filter
Type
Usable period (months)
COST US $
WJNF11
NEO SENSE FILTER
6
44.00
WJIF11
/ WJCF11-POST
INNO SENSE FILTER
/ POST-CARBON FILTER
18
31.00
WJMF11-UF
UF MEMBRANE FILTER
12
63.00
WJCC-02
CERAMIC FILTER
12
11.00
36
* VOC Surrogate Claims
Chemical
Drinking water regulatory
level1 (MCL/MAC) mg/L
Influent challenge
concentration2 mg/L
Chemical reduction
percent
Maximum product water
concentration mg/L
alachlor
0.002
0.050
> 98
0.0013
atrazine
0.003
0.100
> 97
0.0033
benzene
0.005
0.081
> 99
0.0013
carbofuran
0.04
0.190
> 99
0.0013
carbon tetrachloride
0.005
0.078
98
0.00184
chlorobenzene
0.1
0.077
> 99
0.0013
chloropicrin
-
0.015
99
0.00023
2,4-D
0.07
0.110
98
0.00174
dibromochloropropane(DBCP)
0.0002
0.052
> 99
0.000023
0.0013
o-dichlorobenzene
0.6
0.080
> 99
p-dichlorobenzene
0.075
0.040
> 98
0.0013
1,2-dichloroethane
0.005
0.088
955
0.00485
1,1-dichloroethylene
0.007
0.083
> 99
0.0013
cis-1,2-dichloroethylene
0.07
0.170
> 99
0.00053
trans-1,2-dichloroethylene
0.1
0.086
> 99
0.0013
1,2-dichloropropane
0.005
0.080
> 99
0.0013
cis-1,3-dichloropropylene
-
0.079
> 99
0.0013
dinoseb
0.007
0.170
99
0.00024
0.000594
endrin
0.002
0.053
99
ethylbenzene
0.7
0.088
> 99
0.0013
ethylene dilbromide (EDB)
0.00005
0.044
> 99
0.000023
haloacetonitriles (HAN)
bromochloroacetonitrile
dibromoacetonitrile
dichloroacetonitrile
trichloroacetoritrile
-
0.022
0.024
0.0096
0.015
98
98
98
98
0.00053
0.00063
0.00023
0.00033
haloketones (HK):
1,1-dichloro-2-propanone
1,1,1-trichloro-2-propanone
-
0.0072
0.0082
99
96
0.00013
0.00033
heptachlor (H-34,Heptox)
0.0004
0.08
> 99
0.0004
heptachlor epoxide
0.0002
0.01076
98
0.00026
hexachlorobutadiene
-
0.044
> 98
0.0013
hexachlorocyclopentadiene
0.05
0.060
> 99
0.0000023
lindane
0.0002
0.055
> 99
0.000013
methoxychlor
0.04
0.050
> 99
0.00013
pentachlorophenol
0.001
0.096
> 99
0.0013
simazine
0.004
0.120
> 97
0.0043
styrene
0.1
0.150
> 99
0.00053
1,1,2,2-tetrachloroethane
-
0.081
> 99
0.0013
tetrachloroethylene
0.005
0.081
> 99
0.0013
toluene
1
0.078
> 99
0.0013
0.00164
2,4,5-TP (silvex)
0.05
0.270
99
tribromoacetic acid
-
0.042
> 98
0.0013
1,2,4-trichlorobenzene
0.07
0.160
> 99
0.00053
1,1,1-trichloroethane
0.2
0.084
95
0.00464
1,1,2-trichloroethane
0.005
0.150
> 99
0.00053
trichloroethylene
0.005
0.180
> 99
0.00103
trihalomethanes (includes):
chloroform (surrogate chemical)
bromoform
bromodichloromethane
chlorodibromomethane
xylenes (total)
0.080
0.300
95
0.015
10
0.070
> 99
0.0013
1. These harmonized values were agreed upon by representatives of USEPA and Health Canada for the purpose of evaluating products to the requirements of this Standard.
2. Influent challenge levels are average influent concentrations determined in surrogate qualification testing.
3. Maximum product water level was not observed but was set at the detection limit of the analysis.
4. maximum product water level is set at a value determined in surrogate qualification testing.
5. Chemical reduction percent and maximum product water level calculated at chloroform 95% breakthrough point as determined in surrogate qualification testing.
6. The surrogate test results for heptachlor epoxide demonstrated a 98% reduction. These data were used to calculate an upper occurrence concentration which would produce a maximum product water level at the MCL.
37
Woongjin Coway.,Ltd.
658, Yugu-Ri, Yugu Eub, Gongju-Si, Choongchungnam-Do, Korea
Tel.: 82-41-850-7879 Fax.: 82-41-841-7816
MEMO
Others
PERFORMANCE DATA SHEET | CHP-03AU
38
WARRANTY CARD OR WARRANTY LETTER
ONE YEAR LIMITED WARRANTY
WATER FIRTRATION DEVICE CHP-03AR/L/U (“PRODUCT”)
Model:
Serial Number:
Customer Name:
Date of Purchase:
What This Warranty Covers:
Limitations and Exclusions:
Commencing with the date of purchase of the
Product and continuing for a period of one year,
if manufacturing defects in the Product cause the
Product to not operate properly for its intended
use, then subject to the exclusions, conditions, and
limitations contained herein, COWAY at its sole
option will repair or replace the Product.
Decisions as to the extent of repair or replacement
required will be made solely by COWAY.
The remedy under this Warranty is available only
for that portion of the Product exhibiting defects
at the time of the warranty claim. The replacement
Product as well as any remaining original Product
will be warranted only for the original one year
warranty period. This limited warranty applies
only to Product used for an application specified
by COWAY for the Product and applied in strict
accordance with COWAY published specifications
in effect at the time of application. IF PRODUCT IS
USED FOR OTHER THAN ITS INTENDED PURPOSE,
IT IS SOLD AS IS AND WITHOUT ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
TO THE EXTENT PERMITTED BY APPLICABLE LAW,
COWAY DISCLAIMS ANY OTHER WARRANTY
EXPRESS OR IMPLIED, THAN THAT PROVIDED
FOR HEREIN. THIS WARRANTY IS IN LIEU OF AND
EXCLUDES ALL OTHER WARRANTIES, GUARANTEES,
CONDITIONS AND REPRESENTATIONS, EXPRESS
OR IMPLIED, ORAL OR WRITTEN, STATUTORY OR
OTHERWISE, INCLUDING BUT NOT LIMITED TO
ANY IMPLIED CONDITIONS OR WARRANTIES AS
TO THE MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OF THE COWAY PRODUCT.
SOME STATES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO
THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
COWAY DOES NOT AUTHORIZE ANY PERSON
INCLUDING ITS REPRESENTATIVES, TO MAKE ANY
REPRESENTATION OR TO OFFER ANY WARRANTY,
CONDITION OR GUARANTY IN RESPECT OF THE
PRODUCT OTHER THAN THIS WARRANTY. THIS
LIMITED WARRANTY SHALL BE THE OWNER’S
SOLE AND EXCLUSIVE REMEDY AGAINST
COWAY AND COWAY SHALL NOT BE LIABLE FOR
ANY CONSEQUENTIAL, EXEMPLARY, SPECIAL,
INCIDENTAL OR OTHER DAMAGES INCLUDING,
BUT NOT LIMITED TO, LOSS OF PROFITS, AND
LOSS OF USE. INCIDENTAL, CONSEQUENTIAL
AND EXEMPLARY DAMAGES SHALL NOT BE
RECOVERABLE EVEN IF THE REMEDIES OR THE
ACTIONS PROVIDED FOR IN THIS WARRANTY FAIL
OF THEIR ESSENTIAL PURPOSE. SOME STATES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU. COWAY SHALL NOT BE LIABLE
FOR ANY DAMAGES WHICH ARE BASED UPON
NEGLIGENCE, BREACH OF WARRANTY, STRICT
LIABILITY OR ANY OTHER LEGAL THEORY OF
LIABILITY OTHER THAN THE EXCLUSIVE LIABILITY
SET FORTH IN THIS WARRANTY
What This Warranty Does Not Cover:
This Warranty warrants that the Product will be
free from manufacturing defects which affect the
ability of the Product to operate for its intended
use; it is not a warranty that the Product will never
require repairs or to undertake responsibilities,
liabilities or obligations other than those
specifically identified in the preceding section.
COWAY is not responsible or liable for personal
injury or property damage of any kind, even if
arising from a breach of this Warranty.
39
(“OWNER”)
Others
Waiver:
Any implied warranty of merchantability or
fitness for a particular purpose or use, shall be
limited to the duration of the foregoing express
written warranty.
COWAY’s failure at any time to enforce or rely
upon any of the terms or conditions stated
herein shall not be construed to be a waiver of
its rights hereunder.
Conditions of Warranty:
Obtaining Warranty Service and OWNER’S
Duties:
COWAY’s continuing liability under this
Warranty is conditioned upon the following :
a) The defect or damage is not caused
by or is the result of : abnormal use or
conditions; improper storage, unauthorized
modifications or repair; misuse, neglect,
accident, alteration, improper installation or
other acts that are not the fault of Coway or
the manufacturer of the product or that are
not covered by the manufacturer’s warranty;
b) The Product has not been altered, modified
or repaired without prior written approval of
COWAY;
c) The OWNER has notified COWAY in writing
of any failure of the Product covered by this
Warranty within thirty (30) days following
such failure;
d) There has been no misuse, abuse or
negligence with respect to the Product on
the part of the OWNER.
If the Product fails to operate for its
intended purpose, then notify Coway or its
Representative Agency within 48 hours or
within the next business day after discovery
of any defect in the Product. The OWNER must
give written notice to COWAY no later than
thirty (30) days after a defect is discovered or
should by reasonable diligence have been
discovered. Claims under this Warranty will
require proof of purchase by the OWNER.
WARRANTY CARD
Limitations on Implied Warranties:
USA
Add
: WOONGJIN COWAY USA, INC.
695 SOUTH VERMONT, STE. 110(SOUTH TOWER) LOS ANGELES, CA 90005, USA
Call center. : (213) 386-9900 / (213) 480-1600
Fax.
: (213) 386-3990
40
http://www.coway.com
MADE IN KOREA
001
1210108
Download PDF

advertising