User manual | Cradlepoint IBR650 Network Router User Manual

CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Preface
CradlePoint reserves the right to revise this publication and to make changes in the content thereof without obligation to
notify any person or organization of any revisions or changes.
Manual Revisions
Revision
Date
Description
Author
1.0
Sept. 13, 2011
Initial release for Firmware version 3.3.0
Jeremy Cramer
Trademarks
CradlePoint and the CradlePoint logo are registered trademarks of CradlePoint, Inc. in the United States and other
countries. All other company or product names mentioned herein are trademarks or registered trademarks of their
respective companies.
Copyright © 2011 by CradlePoint, Inc.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written consent
by CradlePoint, Inc.
`
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Table of Contents
1
INTRODUCTION ................................................................ 3
1.1
1.2
1.3
2
BASIC SETUP ...................................................................... 13
COMMON PROBLEMS .......................................................... 15
WEB INTERFACE -- ESSENTIALS ........................................ 16
4.1
4.2
4.3
4.4
4.5
5
PORTS, LEDS, AND SWITCHES ................................................. 6
MOUNTING BRACKET .......................................................... 10
7
STATUS ........................................................................... 24
5.1
5.2
5.3
5.4
5.5
CLIENT LIST........................................................................ 25
DASHBOARD ...................................................................... 26
GPS ................................................................................. 29
GRE TUNNELS (ADVANCED MODE ONLY)................................ 30
INTERNET CONNECTIONS ...................................................... 31
`
8
CONTENT FILTERING ............................................................ 39
DHCP SERVER (ADVANCED MODE ONLY) ............................... 42
DNS (ADVANCED MODE ONLY)............................................. 43
FIREWALL (ADVANCED MODE ONLY) ...................................... 46
LOCAL NETWORKS .............................................................. 51
ROUTING (ADVANCED MODE ONLY) ....................................... 61
WIPIPE QOS (ADVANCED MODE ONLY) .................................. 62
INTERNET ........................................................................ 66
7.1
7.2
7.3
7.4
7.5
7.6
7.7
ADMINISTRATOR LOGIN ....................................................... 17
GETTING STARTED – FIRST TIME SETUP................................... 19
QUICK LINKS ...................................................................... 21
BASIC MODE VS. ADVANCED MODE ....................................... 22
NETWORK SETTINGS VS. INTERNET ......................................... 23
STATISTICS......................................................................... 35
SYSTEM LOGS..................................................................... 36
VPN TUNNELS (ADVANCED MODE ONLY) ............................... 37
NETWORK SETTINGS ....................................................... 38
6.1
6.2
6.3
6.4
6.5
6.6
6.7
QUICK START .................................................................. 13
3.1
3.2
4
6
HARDWARE OVERVIEW .................................................... 5
2.1
2.2
3
PACKAGE CONTENTS ............................................................. 3
SYSTEM REQUIREMENTS......................................................... 3
IBR650 OVERVIEW .............................................................. 3
5.6
5.7
5.8
CONNECTION MANAGER ...................................................... 67
DATA USAGE (ADVANCED MODE ONLY) ................................. 70
ETHERNET MANAGER .......................................................... 75
GRE TUNNELS (ADVANCED MODE ONLY)................................ 77
LOAD BALANCE (ADVANCED MODE ONLY) ............................... 80
MODEM SETTINGS .............................................................. 81
VPN TUNNELS (ADVANCED MODE ONLY) ............................... 87
SYSTEM SETTINGS ........................................................... 97
8.1
8.2
8.3
ADMINISTRATION ............................................................... 98
DEVICE ALERTS (ADVANCED MODE ONLY) ............................. 105
GPIO CONNECTOR ........................................................... 107
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
8.4 MANAGED SERVICES (ADVANCED MODE ONLY) ASK YOUR
CRADLEPOINT SALES REPRESENTATIVE FOR DETAILS ........... 109
8.5 SYSTEM CONTROL ............................................................. 110
8.6 SYSTEM SOFTWARE ........................................................... 111
9
GLOSSARY..................................................................... 112
10 APPENDIX ................................................................... 126
10.1
10.2
PRODUCT INFORMATION AND SAFETY GUIDE ....................... 126
SPECIFICATIONS .............................................................. 128
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 2
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
1 INTRODUCTION
1.1 Package Contents





CradlePoint COR: Integrated Broadband Router (IBR650) with embedded high-speed 3G EV-DO rev A modem
Two external 3G EV-DO modem antennas
AC power adapter (12V, 1.5A)
Mounting Hardware
Quick Start Guide
1.2 System Requirements



Either an active subscription for the embedded 3G EV-DO modem or an Ethernet-based modem.
Windows 2000/XP/7, Mac OS X, or Linux Computer.
Internet Explorer v6.0 or higher, Firefox v2.0 or higher, Safari v1.0 or higher.
1.3 IBR650 Overview
COR: THE HEART OF YOUR M2M NETWORK
 For use in business critical high-availability installations such as ATMs, Kiosks, Surveillance, Vehicles, etc. that
require 24x7 connectivity
 Increase your network availability with WiPipe™-powered automatic failover/failback internal functionality
 Supports both wireless and wired Internet connections (two Ethernet ports for either LAN/LAN or WAN/LAN)
 Secure IPSec VPN (5 concurrent sessions maximum)
 Centralize the administration and monitoring of distributed routers using WiPipe Central.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 3
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
ADDITIONAL FEATURES
 Standardized platform and centralized remote management
 Built-in GPS
 IP passthrough
 Up to 5 concurrent VPN endpoint sessions
 Compatible with Cisco, Juniper, SonicWall, and other VPN termination systems
 Establish continuous uptime with optimum total cost of ownership for broad deployment
 Simple to install, configure and maintain with minimal impact on IT
 Virtual LAN capabilities
 Data Usage section that allows users to track and manage modem use relative to data plans
 NAT-less routing
 VPN NAT traversal
The CradlePoint IBR650E is a highly-featured, compact and robust router designed for deployment in critical business
and enterprise applications that require 24x7 connectivity via Ethernet. The router features a built-in high-speed 3G EVDO modem as well as support for wired networks such as DSL or Cable. With its compact size, sleek metal case and
mounting bracket, and external Cellular antennas the IBR650E is ideal for use in high-availability portable or fixed
applications (ATM, kiosk, surveillance, vehicle). With failover/failback capability, the IBR650E supports wired and wireless
internet.
The router increases internet availability and business continuity by detecting network failures and seamlessly switching
over to the other network(s). It is also ideal for deployment as a primary connection solution where wired internet is not
available. The IBR650E provides secure and reliable VPN functionality, allowing users to create, manage, and terminate
up to 5 concurrent IPSec VPN sessions. It allows for secure access to company networks for enterprise applications and
provides a secure way to transmit sensitive data to and from a remote site.
1.3.1 WiPipe Central
CradlePoint‘s cloud-based router management service allows for remote monitoring, configuration, and firmware updates
of deployed routers like the IBR650. WiPipe Central drastically simplifies router administration for businesses using
multiple routers. WiPipe Central can be purchased separately at http://cradlepoint.com/support/wipipe-central.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 4
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
2 HARDWARE OVERVIEW
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 5
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
2.1 Ports, LEDs, and Switches
Power 12VDC: The power connector includes two pins for power and two pins for GPIO
(General Purpose Input/Output) functionality. The included power adapter, however, only
connects to the power pins. You will need a separate adapter for GPIO functionality.
Reset: You can return your router to factory default settings by pressing and holding the
Reset button. This button is recessed, so it requires a pointed object such as a paper clip
to press. Press and hold for 10 seconds to initiate reset.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 6
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Ethernet Ports: By default, the IBR650 has one WAN (Wide Area Network—your internet source) port and one LAN
(Local Area Network) port. Each of these ports can be reconfigured, however, if you need two LAN or two WAN Ethernet
ports.
Ethernet LED:
 Solid Green – connected
 Blinking Green – data transfer activity
Micro USB: This port can be used to attach a direct firmware upgrade to enable manual firmware upgrades if necessary.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 7
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Modem Antennas: The IBR650 comes with two modem antennas to enhance reception for the embedded modem.
These antennas are simple to attach and adjust.
Power On/Off:
 I = On
 O = Off
Power LED:
 Blue = On
 No light = Off
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 8
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
ATTN LED:

Used with Modem LED for additional LED indications below.
Modem LED:
 Green = On and operating normally
 Blinking Green = Connecting
 Amber = Not available (idle, for example)
 Blinking Amber = Cellular data connection error
 No light = Off
Additional LED Indications:
Factory reset button detected
ATTN and modem LEDs blink amber
twice
Error during USB firmware
upgrade
ATTN and modem LEDs blink red
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 9
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
2.2 Mounting Bracket
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 10
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
2.2.1
Attaching the IBR650 to the Mounting Bracket
1) Attach the bracket to the wall or other surface with screws.
NOTE: Screws are not provided because the type of screw required
depends on the mounting surface.
2) Place the router‘s edge
against the bottom of the
bracket.
3) Press the router down
firmly, then push it inside
the bracket. It should
latch.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 11
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
2.2.2
Removing the IBR650 from the Mounting Bracket
From the top of the bracket, press down firmly on the router using your thumb(s) and pull the device out.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 12
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
3 QUICK START
3.1 Basic Setup
1. Attach the modem antennas.
2. Plug the power supply into
an electrical outlet and
connect it to the IBR650.
3. Make sure the power is
switched on.
O = OFF I = ON
3.1.1 Activate Your Modem
A wireless broadband data plan must be added to your IBR650. Wireless broadband data plans are available from
wireless carriers such as Sprint and Verizon. A new line of service can be added or a data plan can be transferred from an
existing account. You will need the ESN number from your product label on your router to add or transfer a line of service.
After adding a data plan to the modem, the modem may need to be activated. To activate the modem:
1. Log in to the IBR650 administration pages (see Accessing the Administration Pages).
2. Select Internet from the top navigation bar and Modem Settings from the dropdown menu (Internet → Modem
Settings).
3. Find and select the CradlePoint modem.
4. Click Update/Activate.
5. Click Activate in the popup.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 13
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
3.1.2
Accessing the Administration Pages
For most users the IBR650 Router can be used
immediately without any special configuration
changes. Simply connect a computer or similar
device to the router‘s Ethernet LAN port with an
Ethernet cable. If you would like to change your
administration password or configure any of the
advanced features of the IBR650, you will need to
log in to the administration pages:



Access your router‘s Administrator Login
screen by opening a web browser window
and typing ―cp/‖ (your router‘s default
hostname) or the IP address ―192.168.0.1‖
into the address bar.
Enter your Default Password. This password can be found on the
bottom of the IBR650. Then click the LOGIN button.
When you log in for the first time, you will be automatically directed to
the First Time Setup Wizard. Follow the instructions given with the
Wizard or see Getting Started – First Time Setup for more information
about using the First Time Setup Wizard.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 14
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
3.2 Common Problems
Please visit CradlePoint Knowledgebase at http://knowledgebase.cradlepoint.com/ for more help and answers to your
other questions.
3.2.1
You are Connected to the Router but Cannot Connect to the Internet
Make sure that you have an active data plan and that your modem has been activated. A wireless broadband data plan
must be added to your IBR650. Wireless broadband data plans are available from wireless carriers such as Sprint and
Verizon. A new line of service can be added or a data plan can be transferred from an existing account. You will need the
ESN number from your product label on your router to add or transfer a line of service.
After adding a data plan to the modem, you must activate the modem:
1. Log in to the IBR650 administration pages (see Accessing the Administration Pages).
2. Select Internet from the top navigation bar and Modem Settings from the dropdown menu (Internet → Modem
Settings).
3. Find and select the CradlePoint modem.
4. Click Update/Activate.
5. Click Activate in the popup.
Finally, if you have an active data plan and you have already activated your modem, you may be out of range of your
service provider. Check your signal strength in the Internet section of the Dashboard (Status → Dashboard). If you have
a weak signal in your location, contact your service provider.
If you are still not online after activating the modem, call CradlePoint Technical Support for further assistance.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 15
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
4 WEB INTERFACE -- ESSENTIALS
The IBR650 has a Web interface for configuration and administration of all features. The interface is organized with a
button for toggling between Basic Mode and Advanced Mode and 5 tabs at the top of the screen:





Getting Started
Status
Network Settings
Internet
System Settings
Web Interface – Essentials contains the following sections to help you more quickly and easy navigate these
administration pages:
4.1 Administrator Login
4.2 Getting Started – First Time Setup
4.3 Quick Links
4.4 Basic Mode vs. Advanced Mode
4.5 Network Settings vs. Internet
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 16
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
4.1 Administrator Login
To access the administration pages, open a Web browser and type the hostname ―cp/‖ or IP address ―http://192.168.0.1‖
into the address bar. The Administrator Login page will appear.
Log in using your administrator password. Initially, this password can be found on the bottom of the IBR650 unit as the
Default Password. This password is also the last eight digits of the unit‘s MAC address.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 17
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
You may have changed the administrator password during initial setup using the First Time Setup Wizard. Log in using
your personalized administrator password.
If you have forgotten your personalized password, you can reset the IBR650 to factory defaults. When you reset the
router, the administrator password will revert back to the Default Password. Press and hold the reset button on the
router unit until the lights flash (Approximately 10-15 seconds). You can then log in using the Default Password (found
on the bottom of your router).
4.1.1
Router Details
The Administrator Login page includes a section that shows the following Router Details:
 Model Number: IBR650E
 Internet Connection: Connected/Disconnected
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 18
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
4.2 Getting Started – First Time Setup
1) Open a browser window and type ―cp/‖ or ―192.168.0.1‖ into the address bar. Press enter/return.
2) When prompted for your password, type the eight character Default Password found on the product label on the
bottom of the IBR650 (this is also the last 8 digits of the router‘s MAC address).
3) When you log in for the first time, you will be
automatically directed to the FIRST TIME
SETUP WIZARD. (Otherwise, go to Getting
Started → First Time Setup).
4) CradlePoint recommends that you change the
router‘s ADMINISTRATOR PASSWORD, which
is used to log in to the administration pages.
5) You can select your TIME ZONE from a
dropdown list. (This may be necessary to
properly show time in your router log, but
typically your router will automatically determine
your time zone through your browser.) Click
NEXT.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 19
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
6) Review your settings and record your
administrator password. You will need this
password to log in to these administration
pages. Move your mouse over the asterisks
to reveal the password.
Click APPLY to save the settings and
update your router.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 20
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
4.3 Quick Links
The CradlePoint logo in the upper left-hand corner of all the administration pages is a link
to the Dashboard (Status → Dashboard), which displays fundamental information about
the router.
The black bar across the top provides quick access to important information and controls.
Click on the image of four signal bars to open a
―Modem Connection Quality‖ popup window that
shows the strength of your internet signal:
(Internet → Connection Manager) where you can
manage your internet sources.
Logout Click to log out of the administration pages.
This links to the
Connection Manager
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 21
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
4.4 Basic Mode vs. Advanced Mode
For less complex uses, the IBR650 can be controlled within Basic Mode. Clicking on the Basic Mode button switches the
complete Web interface to Advanced Mode. Advanced Mode provides several additional features.
The following chart shows the complete list of features found in Basic Mode and found exclusively in Advanced Mode:
Basic Mode
Getting Started
Status
Network Settings
Internet
System Settings
First Time Setup
Client List
Content Filtering
Administration
Dashboard
Local Networks
Connection
Manager
GPS
Ethernet Settings
System Control
Internet
Connections
Modem Settings
System Software
GPIO Connector
Statistics
System Logs
Advanced
Mode
(also
includes all
options in
Basic Mode)
GRE Tunnels
DHCP Server
Data Usage
Device Alerts
VPN Tunnels
DNS
GRE Tunnels
Managed Services
Firewall
Load Balance
Routing
VPN Tunnels
WiPipe QoS
Since Advanced Mode includes all features found in both modes, ALL REMAINING INSTRUCTIONS IN THIS
MANUAL WILL ASSUME YOU ARE IN ADVANCED MODE.
If an expected feature is missing from the user interface, be sure to check that you are using Advanced Mode.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 22
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
4.5 Network Settings vs. Internet
When using the Web interface, it will be important to pay attention to the difference between the internet source for your
IBR650 and the network created by the IBR650. The “Internet” tab broadly refers to the router‘s source of internet, while
the “Network Settings” tab broadly refers to the network created by the router.
The following chart highlights this difference:
Network Settings tab
Internet tab
Internet ―output‖
Internet ―input‖
Network created by IBR650
Source for IBR650
LAN (Local Area Network)
WAN (Wide Area Network)
Examples:


If you want to change the content filtering settings for the network created by the IBR650, go to the Network
Settings tab.
If you have multiple internet sources—such as the embedded modem and an Ethernet connection—for which you
would like to set priority levels, go to the Internet tab.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 23
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
5 STATUS
The Status tab displays information—no adjustments can be made from within these pages. It provides access to 8
submenu options:








Client List
Dashboard
GPS
GRE Tunnels
Internet Connections
Statistics
System Logs
VPN Tunnels
(GRE Tunnels and VPN Tunnels:
Advanced Mode only)
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 24
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
5.1 Client List
The Client List displays the specifications of
each device connected to your router.
Wired Clients. For each device using a
wired connection to your IBR650, the
following information is displayed:
Hostname, IP, and MAC.
Hostname: The name by which each computer or device in a network is known.
IP: The ―IP address,‖ or ―Internet Protocol address,‖ specifies a location for each device.
MAC: This is the "MAC address", a factory-assigned identifier used to identify a specific attached computer or device.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 25
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
5.2 Dashboard
The Dashboard shows fundamental
information about your router, divided into
the following basic categories:



Router Information
Internet
Local Networks
For more in-depth information and/or
configuration options, click on the
Detailed Info link beside the category title.
For each category, this links to:

Router Information: System Settings
→ Administration

Internet: Internet → Connection
Manager

Local Networks: Network Settings →
Local Networks
After the initial setup of the router, every time you log in you will automatically be directed
to this Dashboard. Also, you can click on the CradlePoint logo in the upper left-hand
corner to return to the Dashboard from any page.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 26
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Router Information: “Detailed Info‖ links to System Settings → Administration.







Product: IBR650
Serial: The product serial number.
Firmware: Gives the number of the current firmware version.
Build Date: Year-month-day-hours-minutes-seconds for the most recent firmware upgrade.
CPU Usage: Expressed as a percentage.
Up Time: Total time for current session.
Clock: Current local date and time.
To check for Firmware upgrades, see System Settings → System Software.
Internet: “Detailed Info‖ links to Internet → Connection Manager.







State: Connected/Disconnected
Signal Strength: Expressed as a percentage. (Signal Strength is not included if Ethernet is the WAN type.)
WAN Type: Ethernet or Modem.
Connected Time: The time the current Internet source (WAN) has been connected.
IP Address
Gateway
DNS Servers
For general configuration options, see Internet → Connection Manager. For more in-depth Internet source
configuration options see the appropriate settings page for your WAN type.
 Internet → Ethernet Settings
 Internet → Modem Settings
The IP address and gateway describe your active WAN source.
For DNS server configuration options, see Network Settings → DNS.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 27
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Local Networks: “Detailed Info‖ links to Network Settings → Local Networks.

Clients: The number of current clients.
For each network, the following information is displayed:
 Network Name: IP Address/Netmask
o Route Mode: NAT (Network Address Translation), Standard (NAT-less), IP Passthrough, or Disabled.
o Access: Admin Access, LAN Isolation, UPnP (Universal Plug and Play), and/or DHCP.
To configure a network, see Network Settings → Local Networks.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 28
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
5.3 GPS
If GPS support is enabled and the embedded
modem is connected, this page will show a
graphical view of your router's location. See the
GPS section in System Settings →
Administration to enable GPS support.
GPS information is only displayed if the modem has
sufficient GPS signal strength. Make sure the
modem is in an area where it can receive a signal
from the GPS satellites.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 29
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
5.4 GRE Tunnels (Advanced Mode only)
View the status of configured GRE Tunnels. To set up or edit a GRE tunnel, go to Internet → GRE Tunnels.
Included information:
 Name
 Status
 Transmit (packets/bytes)
 Receive (packets/bytes)
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 30
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
5.5 Internet Connections
The Internet Connections submenu option provides a list of attached WAN devices used as the internet source for the
IBR650. Select one of these devices to see detailed information about that particular device.
For each type of device, different information will be included in the Device Information section. Possible devices
include:


Ethernet
EVDO Modem (embedded modem)
Depending on the device, possible information will be in the following sections: Diagnostics, General Information, IP
Information, and Statistics. For the embedded modem, the Diagnostics section provides specific information about how
the modem is communicating with its carrier.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 31
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
5.5.1
Ethernet
Diagnostics

Connection State (connected, idle,
etc.)
General Information





Protocol Ethernet Static
Product Built-in Ethernet
Type Ethernet
Port
Unique Identifier
Statistics




Outgoing Bits/Second
Incoming Bits/Second
Incoming Bytes
Outgoing Bytes
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 32
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
5.5.2
EVDO Modem (embedded modem)
Diagnostics







Signal Strength (dBm)
PRL Version
Service Display 1xEV-DO,1X
Carrier Status UP or DOWN
Connection Type CDMA
Connection State (connected, idle, etc.)
Connection Uptime
General Information








Product EVDO Modem
Protocol PPP
Unique Identifier
ESN/IMEI
Model MC100E-VZ
Type modem
Port 1
Manufacturer CradlePoint Inc.
IP Information



Netmask
IP Address
Gateway
Statistics



Outgoing Bits/Second
Incoming Bits/Second
Incoming Bytes
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 33
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0

Outgoing Bytes
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 34
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
5.6 Statistics
The Statistics submenu option displays basic
traffic statistics for both LAN and WAN
connections, separating Outgoing Traffic and
Incoming Traffic.
Data Rate: A measure of the amount of
information that is currently being sent or
received through the network.
Data: A measure of the total amount of
information that has been sent or received.
Packets: The number of network packets that
have been sent or received.
Errors: The number of network packets that
failed to be sent or received.
NOTE: Data, Packets, and Errors statistics include only
the numbers since the router was most recently turned
on or reset, not lifetime for the router.
Reset All: Press this button to zero all
statistics. Counting restarts immediately.
Reminder: LAN vs. WAN


LAN, or Local Area Network, is the network you have created through the IBR650.
WAN, or Wide Area Network, is the internet source the IBR650 is using to create a new LAN. Possible WAN
sources include Ethernet or the embedded modem.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 35
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
5.7 System Logs
The router automatically logs (records) events of
possible interest in its internal memory. If there is not
enough internal memory for all events, logs of older
events are deleted, but logs of the latest events are
retained. The log options allow you to filter the router
logs so you can easily find relevant messages. This
router also has external Syslog Server support so
you can send the log files to a computer on your
network that is running a Syslog utility.
Auto Update: The logs automatically refresh
whenever the router creates a new message.
Update: Click to check for new router messages.
Save log to a file: This will open a dialog in your
browser that will allow you to save the router's log to
your computer.
Search: Enter keywords to find specific events.
Level: Select/Deselect from the following levels to
filter messages by priority.
 Critical
 Error
 Warning
 Info
NOTE: The logs are erased whenever the router is rebooted or loses power.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 36
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
5.8 VPN Tunnels (Advanced Mode only)
View the status of configured VPN tunnels. To set up or edit a VPN tunnel, go to Internet → VPN Tunnels.
Included information:
 Name
 Connections
 Status
 Protocols
 Transferred
 Direction
 Time Online
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 37
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6 NETWORK SETTINGS
The Network Settings tab provides access to 7 submenu options for administering the following functions/tasks. These
functions are all related to controlling the LAN (Local Area Network), the network you set up with the IBR650.







Content Filtering
DHCP Server
DNS
Firewall
Local Networks
Routing
WiPipe QoS
(DHCP Server, DNS, Firewall,
Routing, and WiPipe QoS:
Advanced Mode only)
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 38
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.1 Content Filtering
You have two main options for filtering
content in a network created through your
IBR650.
1) Domain / URL Filter Rules: Create a
list of websites that will be either
disallowed (facebook.com, for
example) or allowed exclusively (your
company‘s website, for example).
2) OpenDNS Content Filtering: Allows
several options for filtering rules.
To create Domain / URL Filter Rules, simply input one or more website domain names or URLs. By default, these
websites will be disallowed as part of a Blacklist. You can change this to a Whitelist to exclusively allow these sites.
Enable Whitelist: Domain / URL filters allow you to block access from your network to any external domain or website.
Enabling this as a Whitelist will allow access to only those sites in the list.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 39
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.1.1 OpenDNS
OpenDNS is a service that protects you
online by filtering websites. OpenDNS
protects you from phishing websites and
URL typos once you select a filtering level.






None: Disables Web filtering that
uses OpenDNS,
Minimal: Filters phishing and URL
typos.
Good: Filters any Web site containing
pornography and enables typo and
phishing redirection.
Better: Filters more nudity, sexuality,
and tasteless content.
Best: Filters more nudity, sexuality,
and tasteless content. Selecting ―Best‖ will filter all content that is deemed adult content by OpenDNS.
Custom: Custom OpenDNS settings. See below for more information.
In addition to the standard filtering levels,
you have the following options for filter
control:
Custom OpenDNS: To use the Custom
OpenDNS setting you need to first create an
OpenDNS account. You can create an
account at OpenDNS and click on the
―Create Account‖ link. Follow the onscreen
instructions to create an account.
Once you have an OpenDNS account, enter your account information in order to use your Custom OpenDNS settings.
Custom OpenDNS settings use the DNS-O-MATIC (an OpenDNS Service) API to update the IP address of your
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 40
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
OpenDNS network. In order for Custom settings to work you need to login to DNS-O-MATIC using your OpenDNS
credentials and "Add A Service" for the network specified above.
Enable OpenDNS ISP Filter Bypass Algorithm: It is possible that your Internet Service Provider (ISP) uses the port that
OpenDNS is configured to access, port 53, which will prevent OpenDNS filtering. If OpenDNS does not appear to be
working correctly, enabling this will attempt to bypass those ports when using an OpenDNS content filtering level.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 41
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.2 DHCP Server (Advanced Mode only)
DHCP stands for Dynamic Host Configuration Protocol. The built-in DHCP server automatically assigns IP addresses to
the computers and other devices on each local area network (LAN). In this section you can view a list of assigned IP
addresses and reserve IP addresses for particular devices.
Active Leases: A list of devices that have
been provided DHCP leases. The DHCP
server automatically assigns these leases.
This list will not include any devices that
have static IP addresses on the network.
Reservations: This option lets you reserve
IP addresses; you can assign the same IP
address to the network device with the
specified MAC address any time it requests
an IP address. This is almost the same as
when a device has a static IP address except that the device must still request an IP address from the router. The router
will provide the device the same IP address every time. DHCP Reservations are helpful for server computers on the local
network that are hosting applications such as Web and FTP. Servers on your network should either use a static IP
address or a reservation.
While you have the option to manually input the information to reserve an IP address (Hostname, Hardware Addr, IP
Addr), it is much simpler to select a device under the Active Leases section and click ―Reserve.‖ The selected device‘s
information will automatically be added under Reservations.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 42
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.3 DNS (Advanced Mode only)
DNS, or Domain Name System, is a naming system that translates between domain names (www.cradlepoint.com, for
example) and internet IP addresses (206.207.82.197). A DNS server acts as an internet phone book, translating between
names that make sense to people and the more complex numerical identifiers. The DNS page for the IBR650 has these
distinct functions:
 DNS Settings: By default your router is set to automatically acquire DNS servers through your internet provider
(Automatic). DNS Settings allows you to specify DNS servers of your choosing instead (Static).
 Dynamic DNS Configuration: Allows you to host a server (Web, FTP, etc.) using a domain name that you have
purchased (www.yourname.com) with your dynamically assigned IP address.
 Known Hosts Configuration: Allows you to map a name (printer, scanner, laptop, etc.) to an IP address of a
device on the network.
6.3.1
DNS Settings
You have the option to choose specific DNS
servers for your network instead of using the DNS
servers assigned by your internet provider. The
default DNS servers are usually adequate. You
may want to assign DNS servers if the default DNS
servers are performing poorly, if you want clients to
access DNS servers that you use for customized
addressing, or if you have a local DNS server on your network.
Automatic Config: Automatic or Static (default: Automatic). Switching to ―Static‖ enables you to set specific DNS servers
in the Primary DNS and Secondary DNS fields.
Primary DNS and Secondary DNS: If you choose to specify your DNS servers, then enter the IP addresses of the
servers you want as your primary and secondary DNS servers in these fields. For example, Google Public DNS servers
have the IP addresses 8.8.8.8 and 8.8.4.4 while 4.2.2.2 and 4.2.2.3 are servers from Level 3 Communications.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 43
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.3.2 Dynamic DNS Configuration
The Dynamic DNS feature allows you to host a server (Web, FTP, etc.) using a domain name that you have purchased
(www.yourname.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign
dynamic (changing) IP addresses. When you use a Dynamic DNS service provider, you can enter your host name to
connect to your server, no matter what your IP address is.
Enable Dynamic DNS Service: Enable this
option only if you have purchased your own
domain name and registered with a Dynamic
DNS service provider.
Server Type. Select a Dynamic DNS service
provider from the pull-down list:
 www.DynDNS.org
 www.DNSomatic.com
 www.ChangeIP.com
 www.NO-IP.com
 Custom Server (DynDNS clone)
Custom Server Address. Only available if you
select Custom Server from the Server Address
dropdown list. Enter your custom dynamic DNS
server address here. The server must support
the Dynamic DNS protocol. See
www.dyndns.org for details. Example:
myserver.mydomain.net.
Host name: Enter your host name, fully qualified. For example: myhost.mydomain.net.
User name: Enter the user name or key provided by the Dynamic DNS service provider. If the Dynamic DNS provider
supplies only a key, enter that key for both the User name and Password fields.
Password: Enter the password or key provided by the Dynamic DNS service provider.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 44
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.3.3 Advanced Dynamic DNS Settings
Update period (hours). (Default: 576.) The time between periodic updates to the Dynamic DNS if your dynamic IP
address has not changed. The timeout period is entered in hours so valid values are from 1 to 8760.
Override External IP. The external IP is usually configured automatically during connection. However, in situations where
the unit is within a private network behind a firewall or router, the network's external IP address will have to be manually
configured in this field.
You may find out what your external IP address is by going to http://myip.dnsomatic.com/ in a web browser.
6.3.4
Known Hosts Configuration
The Known Hosts Configuration feature allows
you to map a name (printer, scanner, laptop, etc.)
to an IP address of a device on the network. This
assigns a new hostname that can be used to
conveniently identify a device within the network,
such as an office printer.
Click Add to name a device in your network.
Fill in the following fields:
 Hostname: Choose a name that is meaningful to you. No
spaces are allowed in this field.
 IP address: The address of the device within your
network.
EXAMPLE: a personal laptop with IP address 192.168.0.164 could be
assigned the name ―MyLaptop‖.
Since the assigned name is mapped to an IP address, the
device‘s IP address should not change. To ensure that the device keeps the same IP address, go to the ―Reservations‖
section under Network Settings → DHCP Server and reserve the IP address for the device.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 45
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.4 Firewall (Advanced Mode only)
The router automatically provides a firewall. Unless you configure the router to the contrary, the router does not respond
to unsolicited incoming requests on any port, thereby making your LAN invisible to cyber attackers.
However, some network applications cannot run with a tight firewall. Those applications need to selectively open ports in
the firewall to function correctly. The options on this page control ways of opening the firewall to address the needs of
specific types of applications.
6.4.1
Port Forwarding Rules
A port forwarding rule allows traffic from the
internet to reach a computer on the inside of your
network. For example, a port forwarding rule might
be used to run a Web server.
Exercise caution when adding new rules as they impact the security of your network.
Click Add to create a new port forwarding rule.
Add New Port Forwarding Rule: page 1



Name: Name your rule.
Description: Enter a short description of this rule for future
reference.
Click ―Next‖ to continue.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 46
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
Add New Port Forwarding Rule: page 2




Use Port Range: Changes the selection options to allow you
to input a range of ports (if desired).
Internet Port(s): The port number(s) as you want it defined on
the internet. Typically these will be the same as the local port
numbers, but they do not have to be. These numbers will be
mapped to the local port numbers.
Local Computer: Select the IP address of an attached device
from the dropdown menu, or manually input the IP address of a
device.
Local Port(s): The port number(s) that corresponds to the service (Web server, FTP, etc) on a local computer or
device.
For example, you might input ―80‖ in the Local Port(s) field to open a port for a Web server on a computer within
your network. The Internet Port(s) field could then also be 80, or you could choose another port number that will
be used across the internet to access your Web server. If you choose a number other than 80 for the internet Port,
connections to that number will be mapped to 80—and therefore the Web server—within your network.
Add New Port Forwarding Rule: page 3


Protocol: Select from the following options in the dropdown
menu:
o TCP
o UDP
o TCP & UDP
Click Submit to save your completed port forwarding rule.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 47
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.4.2
IP Filter Rules
An "Incoming" IP filter rule restricts remote access
to computers on your local network. "Outgoing" filter
rules prevent computers on your local network from
initiating communication to the address range
specified in the rule.
This feature is especially useful when combined with
port forwarding and/or DMZ to restrict remote access to a specified host or network range. For example, in order to host a
server you might have opened ports with a port forwarding rule that could expose your LAN to cyber attacks. With an
incoming IP filter rule, you can restrict the access to your LAN to only known devices.







Name: Name your rule.
Direction: ―Incoming‖ or ―Outgoing‖
Action: ―Allow‖ or ―Deny‖
Start Port: Use for a single port or a range of ports.
End Port: Use for a single port or a range of ports.
Network Address
Subnet Mask
Use Start Port, End Port, Network Address, and Subnet Mask to
specify the ports and addresses for which the rule applies. You can
specify a range of ports or a single port (by inputting the same value in
both port fields). Similarly, the subnet mask can be used to define
either a range of addresses (i.e. 255.255.255.0) or a single address
(255.255.255.255).
Example of an IP Filter Rule: Suppose you have opened a port in your firewall in
order to run a server. Someone, Johnny, is abusing that opening, so you would like to
restrict his access. Create a rule that will deny Johnny‘s IP address.



Name: No more Johnny
Direction: Incoming
Action: Deny
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 48
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0




Start Port: 80
End Port: 80
Network Address: 172.22.24.160 (Johnny‘s IP address)
Subnet Mask: 255.255.255.255 (This subnet mask restricts the rule to one single address).
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 49
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.4.3
DMZ (DeMilitarized Zone)
A DMZ host is effectively not firewalled in the sense
that any computer on the internet may attempt to
remotely access network services at the DMZ IP
address. Typical uses involve running a public Web
server or sharing files.
Input the IP Address of a single device in your network to create a DeMilitarized Zone for that device. To ensure that the
IP address of the selected device remains consistent, go to the ―Reservations‖ section under Network Settings → DHCP
Server and reserve the IP address for the device.
As with port forwarding, use caution when enabling the DMZ feature as it can threaten the security of your
network. Only use DMZ as a last resort.
6.4.4
Firewall Options
Anti-Spoof: Anti-Spoof checks help protect against
malicious users faking the source address in
packets they transmit in order to either hide
themselves or to impersonate someone else. Once
the user has spoofed their address they can launch
a network attack without revealing the true source of
the attack or attempt to gain access to network services that are restricted to certain addresses.
Packet Normalization: Normalizing packets helps secure the router in untrusted environments. It does so by "scrubbing"
packets that are ambiguous or might represent a break-in attempt. Packet Normalization also helps insure reliable
connectivity for some WAN devices such as WiMAX modems. Only disable this option if you are sure you do not need it.
Static NAT Ports: If enabled the source port does not translate in TCP and UDP packets during NAT. Some NAT
traversal protocols such as STUN(T) require that the source port stay the same when traversing the firewall.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 50
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.5 Local Networks
This section is used to configure the
settings for networks created by your
router.
The user can set up multiple networks on
the IBR650, each with its own unique
configuration and its own selection of
interfaces. Each local network can be
attached to either of the following types of
interfaces:


Ethernet
VLAN
For example, one network might be just an
isolated network for guests, while another
might be the main network with
administrative access and a VLAN
interface.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 51
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.5.1
Local IP Networks
Local IP Networks displays the following information for each network:






Network Name
IP address/Netmask
DHCP Server (Enabled/Disabled)
Routing Mode (NAT, Standard, IP
Passthrough, Disabled)
Access Control (Admin Access,
UPnP Gateway, LAN Isolation)
Attached Interfaces (Ethernet
group(s) and/or VLAN)
Click Add to configure a new network, or select an existing network and click Edit to view configuration options.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 52
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.5.2
Local Network Editor
The Local Network Editor contains the following tabs: IP Settings, Interfaces, Access Control, and DHCP Server.
IP Settings:
Name: This primarily helps to identify this network during
other administration tasks.
Hostname: [Default: cp (for CradlePoint)] The hostname
is the DNS name associated with the router's local area
network IP address.
NOTE: You can access the router‘s administration pages by typing
the hostname into your browser, so if you change ―cp‖ to another
hostname, you can access the administration pages through the new
hostname.
IP Address: This is the address used by the router for
local area network communication. Changes to this
parameter may require a restart to computers on this
network.
Each network must have a distinct IP address. Most users
will want an address from one of the following private IP ranges:
 10.0.0.1 - 10.255.255.1
 172.16.0.1 - 172.31.255.1
 192.168.0.1 - 192.168.255.1
NOTE: The final number does not have to be 1, but it is a simple, logical convention for routers that leaves higher numbers free for other devices.
Netmask: (Default: 255.255.255.0) The netmask controls how many IP addresses can be used in this network. The
default value allows for 254 IP addresses, which is enough in most cases.
Routing Mode: (Default: NAT) Each network can use a unique routing mode to connect to the internet and other local
networks. NAT is desirable for most configurations. Select from the following options in the dropdown list:
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 53
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0




NAT: Network Address Translation hides private IP addresses behind the router's IP address. This is the simplest
and most common choice for users, because NAT does the translation work for you.
Standard: NAT-less routing. If you select Standard, you must separately configure your IP addresses so that they
will be publically accessible. Typically you will not select this option unless you have a specific reason to bypass
NAT.
IP Passthrough: IP Passthrough passes the IP address given by the modem WAN through the router. All Ethernet
ports must be in LAN mode or Disabled mode, and Hotspot, VPN, and GRE must be disabled.
Disabled: Disable this network.
Interfaces:
Select network interfaces to attach to this network. Choose
from Ethernet ports and VLAN interfaces. Double-click on
any of the interfaces shown on the left in the Available
section to move them to the Selected section on the right
(or highlight an interface and click the + button). To
deselect an interface, double-click on an interface in the
Selected section (or highlight the interface and click the –
button).
If you want more interface options, you must configure
additional Ethernet port groups and VLAN interfaces
separately. See the Local Network Interfaces section
below (on this same administration page: Network
Settings → Local Networks).
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 54
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
Access Control:
Tune the access control settings of this network to match
the intended use. Simply select or deselect any of the
following:



LAN Isolation: When checked, this network will
NOT be allowed to communicate with other local
networks.
UPnP Gateway: Select the UPnP (Universal Plug
and Play) option if you want to enable the UPnP
Gateway service for computers on this network.
Admin Access: When enabled, users may access
these administration pages on this network.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 55
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
DHCP Server:
Changing settings for the DHCP server is optional. The default selections are almost always sufficient.
DHCP Server: (Default: Enabled) When the DHCP server
is enabled, users of your network will be able to
automatically connect to the internet without any special
configuration. It is recommended that you leave this
enabled. Disabling the DHCP server is only
recommended if you have another DHCP server on your
network and it is configured properly.
Range Start and Range End: These designate the range
of values in the reserved pool of IP addresses for the
DHCP server. Values within this range will be given to any
DHCP enabled computers on your network. The default
values are almost always sufficient (default: 72 to 200, as
in 192.168.0.72 to 192.168.0.200).
Example: The IBR650 uses an IP address of 192.168.0.1 for its
primary network by default. A computer designated as a Web server
has a static IP address of 192.168.0.3. Another computer is
designated as an FTP server with a static IP address of 192.168.0.4. The starting IP address for the DHCP server needs to be 192.168.0.5 or
higher.
Lease Time: [Default: 720 minutes (12 hours)] The lease time specifies how long DHCP-enabled computers will wait
before requesting a new DHCP lease. Smaller values are better suited to busy environments.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 56
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.5.3
Local Network Interfaces
Each LAN type—Ethernet and VLAN—has a separate section with configuration options. Unless the default configuration
is sufficient, YOU MUST CONFIGURE EACH INTERFACE SEPARATELY in order to create the desired interface options
for a network. You can then select these interfaces to add to a network in the Local Network Editor (see above).
Select from the following tabs:


Ethernet Port Configuration
VLAN Interfaces
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 57
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
Ethernet Port Configuration
Ethernet Port Configuration provides
controls for your router‘s Ethernet ports.
There are two ports: one set as LAN and
one set as WAN. While default settings
will be sufficient in most circumstances,
you have the ability to control: Mode
(WAN or LAN) and Link Speed.
Additional controls for WAN ports are
available in Internet → Ethernet
Settings.
Mode: WAN or LAN.


Internet (WAN) is used to connect
to another network such as a hotel or office wired network. The WAN connection is used as a possible source of
internet for the IBR650.
Local Network (LAN) is for connecting a computer or similar device directly to the router with an Ethernet cable.
Link Speed: Default setting is Auto. The Auto setting is preferred in most cases.






Auto
10Mbps - Half Duplex
10Mbps - Full Duplex
100Mbps - Half Duplex
100Mbps - Full Duplex
1000Mbps - Full Duplex
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 58
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
Ethernet Port Group Editor
A Port Group represents a logical grouping of Ethernet
ports. Any computers physically connected to ports in a
group will be allowed to freely communicate with each
other.
Since the IBR650 has only 2 Ethernet ports, this feature
will rarely be necessary. It is possible, however, to set both
ports as LAN ports (or both ports as WAN ports) and then
either separate them or group them together. (For
example, you could use one for the primary network and
one for a guest network, or you could use both for the
primary network.)
NOTE: When a port group uses the LAN mode you must separately
ensure that this logical interface is attached to a Local IP Network in
the top panel of this page.
Port Group ID: The Group ID field provides a reference to
this grouping of ports to be used in other parts of the router
configuration. For example, this ID is referenced in the
Local IP Networks configuration to attach this logical group of Ethernet ports with a network configuration. Use a simple
short text phrase to describe a group, such as "main", "guestports", "backup_wan", etc.
Select one or more ports to create a port group that you can subsequently attach to a network in the Local Network
Editor. Double-click on any of the Ethernet ports shown on the left in the Available section to move them to the Selected
section on the right (or highlight a port and click the + button). To deselect an Ethernet port, double-click on an interface in
the Selected section (or highlight the port and click the – button).
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 59
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
VLAN Interfaces
A virtual local area network, or VLAN,
functions as any other physical LAN, but it
enables computers and other devices to
be grouped together even if they are not
physically attached to the same network
switch.
To enable a VLAN, select a VID (virtual LAN ID) and a group of Ethernet ports through which users can access the VLAN.
Then go back up to the Local Network Editor to attach your new VLAN to a network. To use a VLAN, the VID must be
shared with another router or similar device so that multiple physical networks have access to the one virtual network.
Click Add to create a new VLAN interface.
VLAN Editor
VID: An integer value that is the Virtual LAN ID.
Ethernet Group: Select the LAN ports with which you want
to associate the VLAN ID from a dropdown list. Your
Ethernet group must be created separately under Ethernet
Port Configuration.
Click Submit to save your configured VLAN.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 60
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.6 Routing (Advanced Mode only)
Add a new static route to the IP routing table or
edit/remove an existing route.
Static routes are unnecessary for most users.
They are typically only used in networks with
more than one layer, such as when there is a
network within a network so that packet destinations are hidden behind an additional router. Adding a static route is a way
of telling the router about an additional step that packets will need to take to reach their destination.
Click Add to create a new static route.
IP/Network Address: The IP address of the target
network or host.
Type: Select from a dropdown list to specify the type of the
target:
 Network
 Host
Netmask: The Netmask, along with the IP address,
defines the network the computer belongs to and which
other IP addresses the computer can see in the same
LAN. An IP address of 192.168.0.1 along with a Netmask
of 255.255.255.0 defines a network with 256 available IP addresses from 192.168.0.0 to 192.168.0.255.
NOTE: 255.255.255.255 is used to signify only the host that was entered in the IP/Network Address field.
Gateway: Specifies the next hop to be taken if this route is used. A gateway of 0.0.0.0 implies there is no next hop, and
the IP address matched is directly connected to the router on the interface specified: LAN or WAN.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 61
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.7 WiPipe QoS (Advanced Mode only)
When WiPipe QoS (Quality of Service/Traffic
Shaping) is enabled, the router will control the
flow of internet traffic according to the userdefined rules. In other words, Traffic Shaping
improves performance by allowing the user to
prioritize applications.
Enable WiPipe QoS: Click on this box to open
options for controlling internet traffic. You can
control Uplink Speed values or define your own
Traffic Shaping rules. When WiPipe QoS is
enabled, the router restricts the flow of outbound
traffic so as not to exceed the WAN uplink
bandwidth.
Default Uplink Speed: By default, the Uplink
Speed values are set as fast as possible. Click
to deselect default values if you want to restrict
the maximum uplink speed for the internet
source(s) you are using (4G Modem, Ethernet,
and/or 3G Modem).
You might do this to reduce overall bandwidth
use for cost reasons or to prioritize available
bandwidth for download. It is recommended that you experiment with different values for your particular internet
connection to yield the best results.
NOTE: Uplink speed is the speed at which data can be transferred to your ISP. You can test your uplink speed with a service such as
speedtest.net.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 62
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
6.7.1 Add Traffic Shaping Rule
A Traffic Shaping Rule identifies a specific message flow and assigns a priority to that flow. For most applications,
automatic classification will be adequate, and specific Traffic Shaping Rules will not be required.
Traffic Shaping supports overlap between rules, where more than one rule can match for a specific message flow. If more
than one rule matches, the rule with the highest priority will be used.
Name. Create a name for the rule that is meaningful to
you.
Protocol. The protocol used by the messages: TCP,
UDP, or ICMP. Select ―Any‖ if your rule does not control a
specific type of message that uses a specific protocol.
Priority. The priority of the message flow is entered here-15 receives the highest priority (most urgent) and 0
receives the lowest priority (least urgent).
Enable. Specifies whether the entry will be active or
inactive.
Click Next to continue to the next page.
Example: You sometimes work from home, and you share bandwidth with your children. You can set a rule to prioritize your computer and a rule
to reduce priority for their computer. To prioritize your computer, you might use the following settings:
 Name: My Computer
 Protocol: Any (Your computer will use all three protocols; there‘s no reason to restrict this rule to just one protocol)
 Priority: 15
To lower the priority of your children‘s computer, you might use these settings:
 Name: Kids‘ Computer
 Protocol: Any
 Priority: 2
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 63
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
The second page allows you to designate the computer(s) on the local network for which you want to adjust traffic priority.
NOTE: Leaving a field empty will match any IP address and/or any
port number. All fields are optional.
Local Start Port and Local End Port: The rule applies to
a flow of messages whose LAN-side port number is within
the range set here.
Local IP Address: The rule applies to a flow of messages
with this LAN-side IP address.
Local Netmask: The rule applies to a flow of messages
with this LAN-side netmask.
Example (continued from previous page): To select your computer
or your kids‘ computer, you only need to input the Local IP Address.
You can ignore the other settings on this page.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 64
CRADLEPOINT IBR650| USER MANUAL Firmware ver. 3.3.0
The third and last page allows you to designate the
network or server on the internet for which you want to
shape traffic.
NOTE: Leaving a field empty will match any IP address and/or any
port number. All fields are optional.
Remote Start Port and Remote End Port: The rule
applies to a flow of messages whose WAN-side port
number is within the range set here.
Remote IP Address. The rule applies to a flow of
messages with this WAN-side IP address.
Remote Netmask. The rule applies to a flow of messages
with this WAN-side Netmask.
Submit. Click to record the changes you have made.
Example (continued from previous page): Since the goal is simply to control which devices in your network get priority, you can ignore all of the
remote settings. Leave them blank to include all possibilities.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 65
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7 INTERNET
The Internet tab provides access to 7 submenu items for managing a variety of internet connection options.







Connection Manager
Data Usage
Ethernet Settings
GRE Tunnels
Load Balance
Modem Settings
VPN Tunnels
(Data Usage, GRE Tunnels, Load
Balance, and VPN Tunnels:
Advanced Mode only)
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 66
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.1 Connection Manager
The router can establish an uplink via the Ethernet WAN port or the embedded modem. If the primary WAN connection
fails the router will automatically attempt to bring up a new link on another device. This feature is called failover. If Load
Balance is enabled, multiple WAN devices may be plugged in and each may establish a link.
7.1.1
WAN Interfaces
This is a list of the available interfaces used
to access the internet. You can enable, stop,
or start devices from this section. By using
the priority arrows (the arrows in the red
boxes; these show if you have more than
one available interface), you can set the interface the router uses by default and the order that it allows failover. To
configure a specific interface, use the settings page for that type of interface (e.g. Ethernet Settings page for wired
connections).
In the example shown, Ethernet is set as the primary internet source, while the embedded modem is a backup. The
Ethernet is ―Connected‖ while the modem is ―Idle.‖
Load Balance: If this is enabled, the router will use multiple WAN interfaces to increase the data transfer throughput by
using any connected WAN interface consecutively. Selecting Load Balance will automatically start the WAN interface and
add it to the pool of WAN interfaces to use for data transfer. Turning off Load Balance for an active WAN interface may
require the user to restart any current browsing session.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 67
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.1.2
Failure Check (Advanced Mode Only)
If this is enabled, the router will check that the
highest priority active WAN interface can get to the
internet even if the WAN connection is not actively
being used. If the interface goes down, the router
will switch to the next highest priority interface
available. If this is not selected, the router will still
failover to the next highest priority interface but
only after the user has attempted to get out to the
internet and failed.
Idle Check Interval: The amount of time between each check. (Default: 30 seconds. Range: 10-3600 seconds.)
ICMP Ping Check and Ping IP Address: Enable and configure an IP address that the router will use to check if the WAN
connection is available. For best results, select an established public IP address.
For example, you might ping Google Public DNS at 8.8.8.8 or Level 3 Communications at 4.2.2.2.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 68
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.1.3 Failback Configuration (Advanced Mode Only)
This is used to configure failback, which is the
ability to go back to a higher priority WAN
interface if it regains connection to its network.
Usage: Fail back based on the amount of data
passed over time. This is a good setting for when
you have a dual-mode EVDO/WiMAX modem
and you are going in and out of WiMAX
coverage. If the router has failed over to EVDO it
will wait until you have low data usage before
bringing down the EVDO connection to check if a
WiMAX connection can be made.
 High (Rate: 80 KB/s. Time Period: 30
seconds.)
 Normal (Rate: 20 KB/s. Time Period: 90 seconds.)
 Low (Rate: 10 KB/s. Time Period: 240 seconds.)
 Custom (Rate range: 1-100 KB/s. Time Period range: 10-300 seconds.)
Time: Fail back only after a set period of time. (Default: 90 seconds. Range: 10-300 seconds.) This is a good setting if
you have a primary wired WAN connection and only use a modem for failover when your wired connection goes down.
This ensures that the higher priority interface has remained online for a set period of time before it becomes active (in
case the connection is dropping in and out, for example).
Disabled: Deactivate failback mode.
Immediate Mode: Fail back immediately whenever a higher priority interface is plugged in or when there is a priority
change. Immediate failback returns you to the use of your preferred internet source more quickly which may have
advantages such as reducing the cost of a failover data plan, but it may cause more interruptions in your network than
Usage or Time modes.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 69
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.2 Data Usage (Advanced Mode Only)
Data Usage Management & Alerts allows you to create and manage rules that help control the data usage of a modem.
If you have a limited data plan or a price increase on your plan after a certain amount of usage, a Data Usage Rule can
help you track these amounts. You can set a rule to shut down use of a modem and/or send a message when you reach a
data usage amount you set.
Enable Data Usage: Enabled/Disabled. (Default:
Disabled.)
When you select Enabled, you will see the Data Usage
Agreement shown to the right. The purpose of this
agreement is to ensure that you understand that the data
numbers for the IBR650 may not perfectly match those of
your carrier: CradlePoint cannot be held responsible. You
must accept the agreement by clicking Yes in order to
begin creating data usage rules.
Warning: You should set your data limits lower than your
Data Allowance and regularly compare the numbers
provided by the router with the numbers from your carrier.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 70
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.2.1
Data Usage Rules
The Date Usage Rule display shows basic
information for each rule you have created
(including rules created with a template).
The following information is displayed:






Rule Name
Enabled: True/False
Date for Rule Reset
Cycle Type: Daily, Weekly, or
Monthly
Cap: Amount in MB.
Current Usage: Shown as an amount in MB, as a percentage of the cap, and in a bar graph.
Click Add to configure a new Data Usage Rule.
Usage Rule Configuration – page 1
Rule Name: Give your rule a name for later recognition.
WAN Selection: Select from the dropdown list of currently
attached WAN devices.
Assigned Usage in MB: Enter a cap amount in megabytes. 1024
megabytes equals 1 gigabyte.
Rule Enabled: (Default: Enabled.) Click to disable.
Click Next to continue to page 2.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 71
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Usage Rule Configuration – page 2
Cycle Type: How often the rule will reset. The data usage
amount will be reset at the end of each cycle. Select the
length of a cycle from a dropdown menu with the following
choices:
 Daily
 Weekly
 Monthly
Cycle Start Date: Select
the date you wish the
rule to begin. This date
will be used to track
when the rule will be
reset.
Shutdown WAN on Cap: If selected, the WAN device will
shut down when the assigned usage is reached. A cycle
reset or a rule deletion will re-enable the device.
Send Alert on Cap: An email alert will be generated and sent when the assigned usage is reached.
WARNING: The SMTP mail server must be configured in System Settings → Device Alerts.
Custom Alert: When checked you enable a second email to be configured for a percentage of the assigned usage.
Percent of Usage (1-1000): If selected, a custom alert will be sent when your data usage reaches this percentage of your
usage cap. For example, you could set this at 90 percent so that you know when your usage is nearing 100 percent of the
cap.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 72
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.2.2
Template Configuration
Templates allow you to control multiple
WAN devices with the same rule. Each WAN
device that matches a template will
automatically have its own rule created.
Click Add to configure a new Template rule.
Create a Template Name that you can recognize.
The template will apply to one of the following
WAN types:
 All WAN
 All Ethernet
 All Modems
Select one of these types.
The rest of the rule settings options match those in
the Data Usage Rules. See the section above for
additional information about how to configure your
template usage rules.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 73
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.2.3 Historical Data
Historical Data shows a graph of data usage for
each attached WAN source that has an assigned
Data Usage Rule. The graph shows the usage trend
for one day.
Click Add Usage to manually input additional usage
for an attached data source. You might do this if you
used your modem while not attached to your router
and you want to keep an accurate count of your
data usage.
Enter the date of usage by using the pop-up
calendar. Then enter the total data in MB—both in
and out—to update the usage amounts.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 74
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.3 Ethernet Manager
The Ethernet Manager provides
controls for your router‘s Ethernet
WAN ports. By default, only one
port is set as a WAN port, but the
other port can be reconfigured as
a WAN port in Network Settings → Local Networks.
While default settings for each WAN Ethernet port will be sufficient in most circumstances, you have the ability to control:


Connect Method: DHCP (Automatic), Static
(Manual), or PPPoE (Point-to-Point Protocol
over Ethernet).
MAC Address: You have the ability to change
the MAC address, but typically this is
unnecessary. You can match this address with
your device‘s address by clicking: ―Clone Your
PC’s MAC Address‖.
7.3.1 Connect Method
Your router‘s Ethernet ports are automatically configured for DHCP connection. DHCP (Dynamic Host Configuration
Protocol) automatically assigns dynamic IP addresses to devices in your networks. This is preferable in most
circumstances.
If you want to use a Static (Manual) or PPPoE connection instead, you will need to fill out additional information.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 75
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Static (Manual):
 IP Address
 Subnet Mask
 Gateway IP
 Primary DNS Server
 Secondary DNS Server
PPPoE:
 Username
 Password
 Password Confirm
 Service
 Auth Type: None, PAP, CHAP
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 76
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.4 GRE Tunnels (Advanced Mode only)
Generic Routing Encapsulation (GRE) tunnels can be used to create a connection between two private networks. The
IBR650 is enabled for either GRE or VPN tunnels. GRE tunnels are simpler to configure and more flexible for different
kinds of packet exchanges, but VPN tunnels are much more secure.
In order to set up a tunnel you must know the following:
 Local Network and Remote Network addresses for the ―Glue Network,‖ the network that is created by the
administrator that serves as the ―glue‖ between the networks of the tunnel. Each address must be a different IP
address from the same private network, and these addresses together form the endpoints of the tunnel.
 Remote Gateway, the public facing WAN IP address that the local gateway is going to connect to.
 Optionally, you might also want to enable the tunnel Keep Alive feature to monitor the status of a tunnel and more
accurately determine if the tunnel is alive or not.
Click Add to configure a new GRE tunnel.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 77
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Page 1: General
Tunnel Name: Choose a name that is meaningful to you.
Local Network: This is the local side of the ―Glue
Network,‖ a network created by the administrator to form
the tunnel. The user creates the IP address inputted
here. It must be different from the IP addresses of the
networks it is gluing together.
Choose any private IP address from the following three
ranges that doesn‘t match either network:
 10.0.0.0 - 10.255.255.255
 172.16.0.0 - 172.31.255.255
 192.168.0.0 - 192.168.255.255
Remote Network: This is the remote side of the ―Glue
Network.‖ Again, the user must create an IP address that
is distinct from the IP addresses of the networks that are
being glued together.
The Remote Network and Local Network values will be
flipped when inputted for the other side of the tunnel
configuration.
Subnet Mask: This is the subnet mask for the Glue
Network. The Local and Remote Network addresses
must fit with this mask. 255.255.255.0 is a logical choice
for most users.
Remote Gateway: This is the public facing, WAN-side IP address of the network that the local gateway is going to
connect to.
Tunnel Enabled: Select to activate the tunnel.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 78
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Keep Alive: This feature monitors the status of a tunnel. This will more accurately determine if the tunnel is alive or not.
Choose the Rate in seconds for each check (Default: 10 seconds. Range: 2 – 3600 seconds) and the number of Retry
attempts (Default: 3. Range: 1 – 255).
Page 2: Routes
Adding routes allows you to configure what types of
network traffic from the local host or hosts will be allowed
through the tunnel.
Click Add Route to configure a new route. You will need
to input the following information, defined by the remote
network:


Network Address
Netmask: (Default: 255.255.255.0)
You can set the tunnel to connect to a range of IP
addresses or to a single IP address. For example, you
could input 192.168.0.0 and 255.255.255.0 to connect
your tunnel to all the addresses of the remote network in
the 192.168.0.x range. Alternatively, you could select a
single address by inputting that address along with a
Netmask of 255.255.255.255.
Click Save to record each new route.
When you have finished adding routes, click Finish to save your GRE tunnel configuration.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 79
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.5 Load Balance (Advanced Mode only)
When enabled in Connection Manager (Internet → Connection Manager), the router will use multiple WAN interfaces
to increase the data transfer throughput by using any connected WAN interface consecutively. Connections are load
balanced between interfaces based on a dynamic measurement of bandwidth available.
Leave ―Use default rates‖ selected for automatically defined bandwidth values for Load Balance.
The default minimum rate can be changed to reflect the minimum bandwidth used during dynamic measurement. The
dynamic measurement will assume that the interface has at least the specified minimum bandwidth available. You have
the ability to set these minimum rates for:


4G Modem
3G Modem
Range: 100-50000 Kbs.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 80
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.6 Modem Settings
This section allows you to change the
settings for your embedded modem.
7.6.1 Update/Activate a Modem
The embedded modem can be
activated (or reactivated/upgraded).
Select the checkbox next to the
CradlePoint device and click ―Update /
Activate‖.

Modem Activation / Update: Activate, Reactivate, or Upgrade Configuration. Click Activate to start the process.
If the modem is connected when you start an operation
the router will automatically disconnect it. The router may
start another device as a failover measure. When the
operation is done the modem will go back to an idle state,
at which point the router may restart it depending on
failover and failback settings.
NOTE: Only one operation is supported at a time. If you try to start
the same operation on the same modem twice the UI will not report
failure and the request will finish normally when the original request is
done. However if you try to start a different operation or use a
different modem, this second request will fail without interfering with
the pending operation.
Process Timeout: If the process fails an error message
will display.
Activation has a 3-minute timeout.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 81
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.6.2 Modem Connection Settings (Advanced Mode Only)
This section changes settings that affect how
modems attempt to connect to the service
provider's network.
Connection Mode: Typically modem connections
are not set to remain on. The router allows you to
set the type of reconnection mode.
 Always On: A connection to the internet is
continuously maintained.
 On Demand: A connection to the internet is made as needed.
 Manual: The administrator has to navigate to the Connection Manager (Internet → Connection Manager) page
and use the control buttons shown in the WAN Interfaces table.
Maximum Idle Time: The interval at which the machine can be idle before the modem connection is disconnected. This
setting is only valid for the "On Demand" and "Manual" connection modes.
Aggressive Reset: When Aggressive Reset is enabled the system will attempt to maintain a good modem connection. If
the internet has been unreachable for a period of time a reset of the modem will occur in attempt to re-establish the
connection.
Modem Configuration Rules (Advanced
Mode Only)
This section allows you to create simple or
complex rules that affect how individual modems
or classes of modems behave in the router.
7.6.3
Click Add to create a new rule.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 82
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Configuration Rule: First page. Create a name for your rule and the condition for which the rule applies.
Rule Name: Create a name meaningful to you.
Select each of the following to create a condition for
your rule. The condition will be of the following form:
― (When)
is/is not
(value) ‖
For example:
―Type is not WiMAX‖
When:
 Port (Internal USB Port)
 Manufacturer
 Model
 Type (WiMAX, Modem, HSPA)
 Serial Number
 MAC Address
 Unique ID
Value: If you chose Port or Type, select from the dropdown list. If you chose Manufacturer, Model, Serial Number, MAC
Address, or Unique ID, you will need to manually input the information.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 83
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Configuration Rule: WiMAX Settings
WiMAX Realm: Select from the following dropdown
options:







Clear – clearwire-wmx.net
Rover – rover-wmx.net
Sprint 3G/4G – sprintpcs.com
Xohm –xohm.com
BridgeMAXX – bridgeMAXX.com
Time Warner Cable – mobile.rr.com
Comcast – mob.comcast.net
TTLS Authentication Mode: TTLS inner authentication
protocol. Select from the following dropdown options:



MSCHAPv2/MD5 (Microsoft Challenge Handshake
Authentication Protocol version2/Message-Digest
Algorithm 5)
PAP (Password Authentication Protocol)
CHAP (Challenge Handshake Authentication
Protocol)
TTLS Username: Username for TTLS authentication.
TTLS Password: Password for TTLS authentication.
WiMAX Authentication Identity: User ID on the network. Leave this blank unless your provider tells you otherwise.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 84
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Configuration Rule: Modem Settings
AT Dial Script: Enter the AT commands to be used in establishing
a network connection. Each command must be entered on a
separate line. All command responses must include ―OK‖ except the
final command response, which must include ―CONNECT‖.
Example:
AT
AT+CGDCONT=2,‖IP‖,‖isp.cingular‖
ATCT*99***2#
PPP Authentication Protocol: Set this only if your service provider
requires a specific protocol and the Auto option chooses the wrong
one.
 Auto
 PAP (Password Authentication Protocol)
 CHAP (Challenge Handshake Authentication Protocol)
PPP Password: Password for PPP authentication.
PPP Username: Username for PPP authentication.
SIM PIN: PIN number for GSM modem with a locked SIM.
Access Point Name (APN): Some wireless carriers provide multiple Access Point Names that a modem can connect to.
If you wish to specify an APN, enter it into this field. Some examples of APN are ‗isp.cingular‖ and ―vpn.com‖. This APN
will be set in the first profile position.
LTE Connection Mode: Specify how the LTE Multi Mode modem should connect to the network.
 Auto: Let the modem decide which network to use.
 Auto EVDO/1xRTT: Connect to CDMA, letting the modem decide which 3G network to use. Do not attempt to
connect to LTE.
 Force LTE: Connect to LTE only (do not attempt to connect to CDMA/GSM).
 Force EVDO: Connect to CDMA EVDO network only.
 Force 1xRTT: Connect to CDMA 1xRTT network only.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 85
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Configuration Rule: SIM/APN Settings
SIM PIN: PIN number for a GSM modem with a locked
SIM.
Access Point Name (APN): Some wireless carriers
provide multiple Access Point Names that a modem can
connect to.



Default: Let the router choose an APN
automatically.
Manual: Enter an APN by hand.
Select: Select from a dropdown menu of the
profiles already on the SIM.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 86
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.7 VPN Tunnels (Advanced Mode only)
VPN (virtual private network) tunnels are
used to establish a secure connection to a
remote network over a public network. For
example, VPN tunnels can be used across
the internet by an individual to connect to
an office network while traveling or by two
office networks to function as one network.
The two networks set up a secure
connection across the (normally) unsecure
internet by assigning VPN encryption protocols.
The IBR650 uses IPsec (Internet Protocol security) to authenticate and encrypt packets exchanged across the tunnel. To
set up a VPN tunnel with the IBR650 on one end, there must be another device (usually a router) that also supports IPsec
on the other end.
IKE (Internet Key Exchange) is the security protocol in IPsec. IKE has two phases, Phase 1 and Phase 2. The IBR650
has several different security protocol options for each phase, but the default selections will be sufficient for most users.
The VPN tunnel status page allows you to view the state of the VPN tunnels. If a tunnel fails to connect to the remote site,
check the System Logs for more information. You may double click on a cell to directly edit that information.
Click Add to configure a new VPN tunnel.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 87
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.7.1
Page 1: General
Tunnel Name: Choose a name meaningful to you.
Local Identity: This can be left blank for most users. If left blank
it will default to the IP address of the WAN connection. Currently
we only support identifiers in the form of an IP address, a user
fully qualified domain name (user@mydomain.com) or just a
fully qualified domain name (www.mydomain.com). If the
remote side of the tunnel is configured to expect an identifier,
then both must match in order for the negotiation to succeed.
Remote Identity: This can be left blank for most users. If left
blank it will default to the IP address of the WAN connection.
Currently we only support identifiers in the form of an IP
address, a user fully qualified domain name
(user@mydomain.com) or just a fully qualified domain name
(www.mydomain.com). If no identifier is defined then no
verification of the remote peer's identification will be done.
Pre-shared Key: Create a password or key. The routers on both
sides of the tunnel must use this same key.
Mode: Tunnel or Transport. Tunnel Mode is used for
protecting traffic between different networks, when traffic must
pass through an intermediate, untrusted network. Transport
Mode is used for end-to-end communications (for example, for
communications between a client and a server).
Initiator Mode: ―Always On/Boot” or ―On Demand.‖ ―Always On/Boot‖ is used if you want the tunnel to initiate the
tunnel connection whenever the WAN becomes available. On Demand is used if you want the tunnel to initiate a
connection if and only if there is data traffic bound for the remote side of the tunnel.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 88
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Tunnel Enabled: Enabled or Disabled.
MBR1200 Quick Connect: VPN tunnels in the IBR650 have more choices than they do in the MBR1200, so it is more
complex to configure. Check this box to simplify setup by streamlining your options.
7.7.2
Page 2: Networks
Local Network: The Network IP address and the Subnet Mask
define what local devices have access to or can be accessed
from the VPN tunnel. The IBR650 will automatically fill in the
values for your network, but you can change the values to limit
the tunnel to only some of the devices in your network.
NOTE: The local network IP address must be different from the remote
network IP address.
Remote Network: Enter the remote Gateway's IP address or
fully qualified domain name (my.domain.com). It is
recommended you use a dynamic DNS host name instead of the
static IP address. By using the dynamic DNS host name updates
of the remote WAN IP are compensated for while connecting to
a VPN tunnel.
Enter the Network IP address with the Subnet Mask to define
the remote network subnet that the local devices will have
access to.
NOTE: The remote network IP address must be different from the local
network IP address.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 89
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.7.3
Page 3: IKE Phase 1
IKE security has two phases, Phase 1 and Phase 2. You have the ability to distinctly configure each phase, but the default
settings will be sufficient for most users.
To set up a tunnel with a remote site, you need to match your tunnel's IKE negotiation parameters with the remote site. By
selecting several encryption, hash, and DH group options, you
improve your chances for a successful tunnel negotiation. For
greatest compatibility, select all options; for greatest security,
select only the most secure options that your devices support.
Exchange Mode: The IKE protocol has 2 modes of negotiating
phase 1 - Main (also called Identity Protection) and Aggressive.
 In Main mode, IKE separates the key information from
the identities, allowing for the identities of peers to be
secure at the expense of extra packet exchanges.
 In Aggressive mode, IKE tries to combine as much
information into fewer packets while maintaining security.
Aggressive mode is slightly faster but less secure.
Because it has better security, Main mode is recommended for
most users.
Key Lifetime: The lifetime of the generated keys of Phase 1 of
the IPsec negotiation from IKE. After the time has expired, IKE
will renegotiate a new set of Phase 1 keys.
Encryption, Hash, and DH Groups: Each IKE exchange uses
one encryption algorithm, one hash function, and one DH group
to make a secure exchange.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 90
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0



Encryption: Used to encrypt messages sent and received by IPsec.
o AES 128
o AES 256
o Blowfish
o CAST
o DES
o 3DES
Hash: Used to compare, authenticate, and validate that data across the VPN arrives in its intended form and to
derive keys used by IPsec.
o MD5
o SHA1
o SHA2 256
o SHA2 384
o SHA2 512
DH Groups: The DH (Diffie-Hellman) Group is a property of IKE and is used to determine the length of prime
numbers associated with key generation. The strength of the key generated is partially determined by the strength
of the DH Group. Group 5, for instance, has greater strength than Group 2.
o DH group 1: 768-bit key.
o DH group 2: 1024-bit key.
o DH group 5: 1536-bit key.
In Phase 1, only one DH group can be selected while using Aggressive exchange mode.
By default, all the algorithms (encryption, hash, and DH groups) supported by the IBR650 are checked, which means they
are allowed for any given exchange. Deselect these options to limit which algorithms will be accepted. Be sure to check
that the router (or similar device) at the other end of the tunnel has matching algorithms.
The algorithms are listed in order by priority. You can reorder this priority list by clicking and dragging algorithms up or
down. Any selected algorithm may be used for IKE exchange, but the algorithms on the top of the list are more likely to be
used more often.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 91
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.7.4
Page 4: IKE Phase 2
Perfect Forward Secrecy (PFS): Enabling this feature will
require IKE to generate a new set of keys in Phase 2 rather than
using the same key generated in Phase 1.
Additionally, the new keys generated in Phase 2 (with this option
enabled) are exchanged in an encrypted session. Enabling this
feature affords the policy greater security.
Key Lifetime: The lifetime of the generated keys of Phase 2 of
the IPsec negotiation from IKE. After the time has expired, IKE
will renegotiate a new set of Phase 2 keys.
Phase 2 has the same selection of Encryption, Hash, and DH
Groups as Phase 1, but you are restricted to only one DH
Group. Phase 2 and Phase 1 selections do not have to match.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 92
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.7.5
Page 5: Dead Peer Detection
Dead Peer Detection (DPD) defines how the router will detect
when one end of the IPsec session loses connection while a
policy is in use.
Connection Idle Time allows you to configure how long the
router will allow an IPsec session to be idle before beginning to
send Dead Peer Detection (DPD) packets to the peer machine.
Request Frequency allows you to adjust the delay between
these DPD packets to send as quickly as every 2 seconds up to
30 seconds apart.
Additionally, you can specify how many Maximum Requests to
send at the selected time interval before the tunnel is considered
dead.
You must click Finish to save your VPN tunnel.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 93
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.7.6 Page 6: Tunnel Summary
The final page of the tunnel configuration interface is a summary of the tunnel specifications. This is especially helpful for
matching this information with the router (or similar device) at the other end of the tunnel.










Tunnel Name
Mode
Initiation Mode
Pre-shared Key
Local Network
Remote Gateway
Remote Network
IKE Phase 1:
o Exchange Mode
o Key Lifetime (Secs)
o Encryption
o Hash
o DH Groups
IKE Phase 2:
o PFS
o Key Lifetime (Secs)
o Encryption
o Hash
o DH Groups
DPD
Click Yes at the bottom of the Tunnel Summary page to save
your configuration changes. This will cause active tunnels to
restart.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 94
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.7.7
Global VPN Settings
These settings apply to all configured VPN tunnels. Changing the Global VPN Settings is rarely necessary; the default
values are almost always sufficient.




IKE / ISAKMP Port: Internet Key Exchange / Internet Security Association and Key Management Protocol port.
Default: 500. This is a standard VPN port that usually does not need to be changed.
IKE / ISAKMP NAT-T Port: Internet Key Exchange / Internet Security Association and Key Management Protocol
network address translation traversal port. Default: 4500. This is a standard VPN NAT-T port that usually does not
need to be changed.
NAT-T KeepAlive Interval: Default: 20 seconds. Range: 0-3600 seconds. 20 seconds will be sufficient in almost
all cases.
Tunnel Connect Retry: Default: 30 seconds. Range: 10-255 seconds. 30 seconds will be sufficient in almost all
cases.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 95
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
7.7.8
VPN with NAT-T
If one side of a planned VPN tunnel is behind a NAT (network address translation) firewall, the setup of your tunnel
requires the following specifications:
1. Each side of the tunnel must use both a Local Identity and a Remote Identity. These must match the identities on
the other side: The Local Identity must match the Remote Identity on the other side of the tunnel, and vice versa. In
this case, these identities can each be a simple word.
2. The Tunnel Name for the side of the tunnel that is not behind the NAT firewall must be ―anonymous‖.
3. The VPN tunnel must be initiated from the side that is behind the NAT firewall.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 96
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
8 SYSTEM SETTINGS
The System Settings tab has 6 submenu options that provide access to tools for broad administrative control of the
IBR650:






Administration
Device Alerts
GPIO Connector
Managed Services
System Control
System Software
(Device Alerts and Managed
Services: Advanced Mode only)
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 97
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
8.1 Administration
Select the Administration submenu item in order to control any of the following functions:








8.1.1
Web Login
Network Time Protocol
Timezone
Bounce Pages
UPnP
Remote Management
GPS
Syslog Settings
Web Login
This password is the administration password. It allows a
user to change router settings. This password can also be
changed through the First Time Setup Wizard. The default
password is found on the bottom of the router.
8.1.2
Network Time Protocol
Enabling NTP will tell the router to get its system time from
a remote server on the internet. If you do not enable NTP
then the router time will be based on when the router
firmware was built, which is guaranteed to be wrong.
Whenever the internet connection is re-established and
once a week thereafter the router will ask the server for the current time so it can correct itself.
You then have the option of selecting an NTP server and adjusting the NTP server port. Any of the given NTP servers will
be sufficient unless, for example, you need to synchronize your router‘s time with other devices in a network.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 98
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
8.1.3
Timezone
This is the time zone and daylight savings setting
used by the router for its own clock. You can also
select this in the First Time Setup Wizard, but
normally the router will automatically select the
correct time zone from the browser.
Daylight Savings Time: Select this checkbox if your location observes daylight savings time.
8.1.4
Bounce Pages
Bounce pages show up in your web browser when
the router is not connected to the internet. They
inform you that you are not connected and try to
explain why. If you disable bounce pages then you
will just get the usual browser timeout. In the normal case when the router is connected to the internet you don't see them
at all.
This allows a user to disable bounce pages for cases where the router WAN link is down.
8.1.5
UPnP
Universal Plug and Play is a set of networking
protocols standardized by the UPnP Forum. UPnP
enables clients to determine network configuration
and configure the network to allow traffic through the firewall without direct user interaction. UPnP can simplify the use of
special applications or devices that require network configuration, but can also allow unprivileged users to manipulate
network configuration.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 99
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
8.1.6
Remote Management
Allows a user to enable incoming WAN pings or to
change settings for the router from the internet using
the router's internet address.
Allow WAN pings: When enabled the functionality
allows an external WAN client to ping the router.
WAN Hostname: This hostname is the DNS name
associated with the router's internet connection
interface. If DHCP is used on the interface this
hostname will be used when requesting a DHCP
lease.
Allow Remote Web Administration: When remote
administration is enabled it allows access to these
administration web pages from the internet. With it disabled, you must be a client on the local network to access the
administration website. For security, remote access is usually done via a non-standard http port. Additionally, encrypted
connections can be required for an added level of security. Requiring a secure (https) connection is recommended.



Require Secure Connection
HTTP Port: Default: 8080. This option is disabled if you select ―Require Secure Connection‖.
Secure HTTPS Port: Default: 8443.
Enable SSH Server: When the router's SSH server is enabled you may access the router's command line interface (CLI)
using the standards based SSH protocol. Use the username "admin" and the standard system password to login.


SSH Server Port: Default: 22.
Allow Remote SSH Access
Technical Support Access: Only enable this option if instructed by a CradlePoint support agent.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 100
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
8.1.7 GPS
If you have an attached device with GPS support, you can enable a graphical view of your router‘s location which will
appear in Status → GPS Status.
Users can configure GPS NMEA GGA format
sentence reporting, available through a routerbased server and/or a remote server.
NOTE: Some carriers disable GPS support in otherwise
supported modems. If you encounter issues with obtaining a
fix, contact your carrier and ensure that GPS is supported.




Enable GPS support: Enables support for
querying GPS information from supported
modems.
Enable GPS server on WAN: Enables a
TCP server on the WAN side of the firewall,
which will periodically send GPS NMEA
sentences to connected clients.
Enable GPS server on LAN: Enables a TCP server on the LAN side of the firewall, which will periodically send
GPS NMEA sentences to connected clients.
o GPS server port number
Enable GPS reporting to remote server: Enables periodic reporting of GPS NMEA sentences to a remote server.
The router will buffer NMEA data if errors are encountered or if the internet connection goes down and send the
buffered sentences when the connection is restored.
o Remote server hostname or IP
o Remote server port
o Report only over specific time interval: Restricts the NMEA sentence reporting to a remote server to a
specific time interval.
The following GPS spec is copied from http://aprs.gids.nl/nmea/
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 101
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
8.1.8
$GPGGA – Global Positioning System Fix Data
Name
Example Data
Description
Sentence Identifier
$GPGGA
Global Positioning System Fix Data
Time
170834
17:08:34 Z
Latitude
4124.8963, N
41d 24.8963' N or 41d 24' 54" N
Longitude
08151.6838, W 81d 51.6838' W or 81d 51' 41" W
Fix Quality:
- 0 = Invalid
- 1 = GPS fix
- 2 = DGPS fix
1
Data is from a GPS fix
Number of Satellites
05
5 Satellites are in view
Horizontal Dilution of Precision (HDOP) 1.5
Relative accuracy of horizontal position
Altitude
280.2 meters above mean sea level
280.2, M
Height of geoid above WGS84 ellipsoid -34.0, M
-34.0 meters
Time since last DGPS update
blank
No last update
DGPS reference station id
blank
No station id
Checksum
*75
Used by program to check for transmission errors
Courtesy of Brian McClure, N8PQI.
Global Positioning System Fix Data. Time, position, and fix related data for a GPS receiver.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 102
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
eg2. $--GGA,hhmmss.ss,llll.ll,a,yyyyy.yy,a,x,xx,x.x,x.x,M,x.x,M,x.x,xxxx
hhmmss.ss = UTC of position
llll.ll = latitude of position
a = N or S
yyyyy.yy = Longitude of position
a = E or W
x = GPS Quality indicator (0=no fix, 1=GPS fix, 2=Dif. GPS fix)
xx = number of satellites in use
x.x = horizontal dilution of precision
x.x = Antenna altitude above mean-sea-level
M = units of antenna altitude, meters
x.x = Geoidal separation
M = units of geoidal separation, meters
x.x = Age of Differential GPS data (seconds)
xxxx = Differential reference station ID
eg3. $GPGGA,hhmmss.ss,llll.ll,a,yyyyy.yy,a,x,xx,x.x,x.x,M,x.x,M,x.x,xxxx*hh
1
2
3
4
5
6
7
8
9
10
11
12
= UTC of Position
= Latitude
= N or S
= Longitude
= E or W
= GPS quality indicator (0=invalid; 1=GPS fix; 2=Diff. GPS fix)
= Number of satellites in use [not those in view]
= Horizontal dilution of position
= Antenna altitude above/below mean sea level (geoid)
= Meters (Antenna height unit)
= Geoidal separation (Diff. between WGS-84 earth ellipsoid and mean sea level. -=geoid is below WGS-84 ellipsoid)
= Meters (Units of geoidal separation)
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 103
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
13 = Age in seconds since last update from diff. reference station
14 = Diff. reference station ID#
15 = Checksum
8.1.9
Syslog Settings
Enabling this option will send log messages to a
specified Syslog server. After enabling, type the
Hostname or IP address of the Syslog server.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 104
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
8.2 Device Alerts (Advanced Mode only)
The Device Alerts submenu choice allows you
to receive email notifications of specific system
events. YOU MUST ENABLE AN SMTP EMAIL
SERVER TO RECEIVE ALERTS. Alerts can be
included for the following:





Firmware Upgrade Available: A
firmware update is available for this
device.
WAN Device Status Change: An
attached WAN device has changed
status. The possible statuses are
plugged, unplugged, connected, and
disconnected.
Login Failure: A failed login attempt has been detected.
Full System Log: The system log has filled. This alert contains the contents of the system log.
Recurring System Log: The system log is sent periodically. This alert contains all of the system events since the
last recurring alert. It can be scheduled for daily, weekly and monthly reports. You also choose the time you want
the alert sent.
8.2.1 SMTP Mail Server
Since the IBR650 does not have its own email server, to receive alerts you must enable an SMTP server. This is possible
through most email services (Gmail, Yahoo, etc.).
Each SMTP server will have different specifications for setup, so you have to look those up separately. The following is an
example using Gmail:
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 105
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0







Server Address: smtp.gmail.com
Server Port: 587 (for TLS, or
Transport Layer Security port; the
IBR650 does not support SSL).
Authentication Required: For
Gmail, mark this checkbox.
User Name: Your full email
address
Password: Your Gmail password
From Address: Your email
address
To Address: Your email address
Once you have filled in the information for
the SMTP server, click on the ―Verify
SMTP Settings‖ button. You should receive a test email at your account.
Advanced: Delivery Options
Email Subject Prefix: This optional string
is prefixed to the alert subject. It can be
customized to help you identify alerts
from specific routers.
Retry Attempts: The number of attempts made to send an alert to the mail server. After the attempts are exhausted, the
alert is discarded.
Retry Delay: The delay between retry attempts.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 106
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
8.3 GPIO Connector
The power connector includes two pins defined for general purpose LVTTL compatible input and output. These pins are
ESD protected and the input is 5V tolerant.
NOTE: GPIO functionality requires a separate adapter to connect to the I/O pins.
Pin Definition
1
Ground
2
12VDC Power
3
Input: LVTTL Digital Input with 50K ohm pullup to 3.3VDC (5V tolerant)
4
Output: LVTTL Digital Output (capable of source/sink of 50mA)
This section is used to configure these Input and Output General Purpose I/O pins.
Current Value: Displays HIGH or LOW for both the Input Pin and Output Pin.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 107
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Input Pin – The Input Pin can be used to read a value—either high or low—from an external device and either display
that value on this administration page (as the Current Value) or cause the router to reset. Select one of the following
options from the dropdown menu:



Default/Ignored: In this mode the input pin is not used.
Input Sensing: In this mode the logic state (high or low) is automatically sensed by the router and is readable as
the Current Value.
Router Reset: In this mode an external device can reset the router by holding the input low for 10-seconds.
Output Pin – The Output Pin can be used to allow an external device to read either whether the router is running or
whether the modem is connected. Select one of the following options from the dropdown menu:



Default/Low: In this mode the output pin is not used and is at 0V (ground potential).
Set High/Router Running: In these modes the output pin is logic low while the router is booting and transitions to
logic high when the router is fully running. If the router is reset, the output returns to low until the router has fully
rebooted.
Modem Connected: In this mode the output pin is logic low until the modem has connected to a tower. If the
connection drops, this output is set low until the connection is restored.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 108
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
8.4 Managed Services (Advanced Mode only) ASK YOUR CRADLEPOINT SALES
REPRESENTATIVE FOR DETAILS
Managed Services allow you to centralize your router configuration using the WiPipe Central server. WiPipe Central
services must be purchased separately.
Enable Services: Enables the WiPipe
Central client to contact the server.
Ethernet Communication Only: The
WiPipe Central client will not start unless
the WAN is Ethernet.
Registration URL: Register your router
using the code provided by CradlePoint
when you purchase WiPipe Central.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 109
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
8.5 System Control
Restore to Factory Defaults: This changes all
settings back to their default values.
Reboot The Device: This causes the router to
restart.
Advanced: System Automatic Reboot
and Ping Test
Scheduled Reboot: This causes the router to
restart at a user-determined time.
Watchdog Reboot: This causes the router to
automatically restart when it determines
unrecoverable error condition has occurred.
an
Ping Test: A simple test to check internet
connectivity. Type the Hostname or IP address of
the computer you want to ping and press 'Enter' or
click the 'Ping' button.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 110
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
8.6 System Software
Firmware Upgrade: This allows the
administrator to load new firmware onto the
router to add new features or fix defects. If you
are happy with the operation of the router, you
may not want to upgrade just because a new
version is available. Check the firmware release
notes for information to decide if you should
upgrade or not.
Automatic (Internet): Have the router download
the file and perform the upgrade with no user
interaction.
Manual Firmware Upload: Upload the router firmware from an attached computer.
Factory Reset: Set default settings to match the new firmware. This is safest, as settings may have changed. You should
back up your current settings and restore them after the new firmware is loaded.
Backup Current Settings: Save your current settings to a file on a computer.
Restore Settings: Restore your previous settings from a file on a computer.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 111
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
9 GLOSSARY
802.11
Alphanumeric
A family of specifications for wireless local area networks
(WLANs) developed by a working group of the Institute of
Electrical and Electronics Engineers (IEEE).
Characters A-Z and 0-9.
Access Control List
ACL. This is a database of network devices that are
allowed to access resources on the network.
Access Point
AP. Device that allows wireless clients to connect to it
and access the network.
ActiveX
A Microsoft specification for the interaction of software
components.
Antenna
Used to transmit and receive RF signals.
AppleTalk
A set of Local Area Network protocols developed by
Apple for their computer systems.
AppleTalk Address Resolution Protocol
AARP. Used to map the MAC addresses of Apple
computers to their AppleTalk network addresses, so that
conversions can be made in both directions.
Application layer
Peer-to-Peer network between wireless clients.
7th Layer of the OSI model. Provides services to
applications to ensure that they can communicate
properly with other applications on a network.
Address Resolution Protocol
ASCII
ARP. Used to map MAC addresses to IP addresses so
that conversions can be made in both directions.
ADSL
American Standard Code for Information Interchange.
This system of characters is most commonly used for text
files.
Asymmetric Digital Subscriber Line.
Attenuation
Advanced Encryption Standard
The loss in strength of digital and analog signals. The
loss is greater when the signal is being transmitted over
long distances.
Ad-hoc network
AES. Government encryption standard.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 112
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Authentication
Bit rate
To provide credentials, like a Password, in order to verify
that the person or device is really who they are claiming
to be.
The amount of bits that pass in given amount of time.
Automatic Private IP Addressing
APIPA. An IP address that a Windows computer will
assign itself when it is configured to obtain an IP address
automatically but no DHCP server is available on the
network.
Backward Compatible
The ability for new devices to communicate and interact
with older legacy devices to guarantee interoperability.
Bandwidth
The maximum amount of bytes or bits per second that
can be transmitted to and from a network device.
Bit/sec
Bits per second.
BOOTP
Bootstrap Protocol. Allows for computers to be booted up
and given an IP address with no user intervention.
Bottleneck
A time during processes when something causes the
process to slowdown or stop all together.
Broadband
A wide band of frequencies available for transmitting
data.
Broadcast
Basic Input/Output System
Transmitting data in all directions at once.
BIOS. A program that the processor of a computer uses
to startup the system once it is turned on.
Browser
Baud
A program that allows you to access resources on the
web and provides them to you graphically.
Data transmission speed.
Cable modem
Beacon
A device that allows you to connect a computer up to a
coaxial cable and receive internet access from your
Cable provider.
A data frame by which one of the stations in a WiFi
network periodically broadcasts network control data to
other wireless stations.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 113
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
CardBus
Data-Link layer
A newer version of the PC Card or PCMCIA interface. It
supports a 32- bit data path, DMA, and consumes less
voltage.
The second layer of the OSI model. Controls the
movement of data on the physical link of a network.
CAT 5
Category 5. Used for 10/100 Mbps or 1Gbps Ethernet
connections.
Organizes information so that it can be managed
updated, as well as easily accessed by users or
applications.
Client
DB-25
A program or user that requests data from a server.
A 25-pin male connector for attaching External modems
or RS-232 serial devices.
Collision
Database
When do two devices on the same Ethernet network try
and transmit data at the exact same time.
DB-9
Cookie
dBd
Information that is stored on the hard drive of your
computer that holds your preferences to the site that
gave your computer the cookie.
Decibels related to dipole antenna.
Data
Information that has been translated into binary so that it
can be processed or moved to another device.
A 9-pin connector for RS-232 connections
dBi
Decibels relative to isotropic radiator.
dBm
Decibels relative to one milliwatt.
Data Encryption Standard
Decrypt
Uses a randomly selected 56-bit key that must be known
by both the sender and the receiver when information is
exchanged.
To unscramble an encrypted message back into plain
text.
Default
A predetermined value or setting that is used by a
program when no user input has been entered for this
value or setting.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 114
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Demilitarized zone
Download
DMZ: A single computer or group of computers that can
be accessed by both users on the internet as well as
users on the Local Network, but that is not protected by
the same security as the Local Network.
To send a request from one computer to another and
have the file transmitted back to the requesting computer.
DHCP
Dynamic Host Configuration Protocol: Used to
automatically assign IP addresses from a predefined pool
of addresses to computers or devices that request them.
Digital certificate
An electronic method of providing credentials to a server
in order to have access to it or a network.
Direct Sequence Spread Spectrum
DSSS: Modulation technique used by 802.11b wireless
devices.
DMZ
DSL
Digital Subscriber Line. High
connection over telephone lines.
internet
Duplex
Sending and Receiving data transmissions at the same
time.
Dynamic DNS service
Dynamic DNS is provided by companies to allow users
with Dynamic IP addresses to obtain a Domain Name
that will always be linked to their changing IP address.
The IP address is updated by either client software
running on a computer or by a router that supports
Dynamic DNS, whenever the IP address changes.
―Demilitarized Zone‖. A computer that logically sits in a
―no-mans-land‖ between the LAN and the WAN. The
DMZ computer trades some of the protection of the
router‘s security mechanisms for the convenience of
being directly addressable from the internet.
Dynamic IP address
DNS
Extensible Authentication Protocol.
Domain Name System: Translates Domain Names to IP
addresses.
Email
Domain name
bandwidth
IP address that is assigned by a DHCP server and that
may change. Cable internet providers usually use this
method to assign IP addresses to their customers.
EAP
Electronic Mail is a computer-stored message that is
transmitted over the internet.
A name that is associated with an IP address.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 115
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Encryption
Fragmentation
Converting data into cyphertext so that it cannot be easily
read.
Breaking up data into smaller pieces to make it easier to
store.
Ethernet
FTP
The most widely used technology for Local Area
Networks.
File Transfer Protocol. Easiest way to transfer files
between computers on the internet.
Fiber optic
Full-duplex
A way of sending data through light impulses over glass
or plastic wire or fiber.
Sending and Receiving data at the same time.
File server
The amount an amplifier boosts the wireless signal.
A computer on a network that stores data so that the
other computers on the network can all access it.
Gateway
File sharing
Gain
A device that connects your network to another, like the
internet.
Allowing data from computers on a network to be
accessed by other computers on the network with
different levels of access rights.
Gbps
Firewall
Gigabit Ethernet
A device that protects resources of the Local Area
Network from unauthorized users outside of the local
network.
Transmission technology that provides a data rate of 1
billion bits per second.
Firmware
Graphical user interface.
Programming that is inserted into a hardware device that
tells it how to function.
H.323
© 2011 CRADLEPOINT, INC.
Gigabits per second.
GUI
A standard that provides consistency of voice and video
transmissions and compatibility for video conferencing
devices.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 116
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Half-duplex
IEEE
Data cannot be transmitted and received at the same
time.
Institute of Electrical and Electronics Engineers.
Hashing
Transforming a string of characters into a shorter string
with a predefined length.
Internet Group Management Protocol is used to make
sure that computers can report their multicast group
membership to adjacent routers.
Hexadecimal
IIS
Characters 0-9 and A-F.
Internet Information Server is a WEB server and FTP
server provided by Microsoft.
Hop
The action of data packets being transmitted from one
router to another.
IGMP
IKE
Host
Internet Key Exchange is used to ensure security for
VPN connections.
Computer on a network.
Infrastructure
HTTP
In terms of a wireless network, this is when wireless
clients use an access point to gain access to the network.
Hypertext Transfer Protocol is used to transfer files from
HTTP servers (web servers) to HTTP clients (web
browsers).
HTTPS
HTTP over SSL is used to encrypt and decrypt HTTP
transmissions.
Hub
A networking device that connects multiple devices
together.
ICMP
Internet Control Message Protocol.
© 2011 CRADLEPOINT, INC.
Internet
A system of worldwide networks that use TCP/IP to allow
for resources to be accessed from computers around the
world.
Internet Explorer
A World Wide Web browser created and provided by
Microsoft.
Internet Protocol
The method of transferring data from one computer to
another on the internet.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 117
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Internet Protocol Security
Java
IPsec provides security at the packet processing layer of
network communication.
A programming language used to create programs and
applets for web pages.
Internet Service Provider
Kbps
An ISP provides access to the internet to individuals or
companies.
Kilobits per second.
Intranet
Kilobyte.
A private network.
L2TP
Intrusion Detection
Layer 2 Tunneling Protocol.
A type of security that scans a network to detect attacks
coming from inside and outside of the network.
LAN
IP
Kbyte
Local Area Network.
Latency
Internet Protocol.
IP address
A 32-bit number, when talking about Internet Protocol
Version 4, that identifies each computer that transmits
data on the internet or on an intranet.
IPsec
Internet Protocol Security.
IPX
Internetwork Packet Exchange is a networking protocol
developed by Novell to enable their Netware clients and
servers to communicate.
The amount of time that it takes a packet to get from the
one point to another on a network. Also referred to as
delay.
LED
Light Emitting Diode.
Legacy
Older devices or technology.
Local Area Network
LAN. A group of computers in a building that usually
access files from a server.
ISP
Internet Service Provider.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 118
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
LPR/LPD
MPPE
―Line Printer Requestor‖/‖Line Printer Daemon‖. A
TCP/IP protocol for transmitting streams of printer data.
Microsoft Point-to-Point Encryption is used to secure data
transmissions over PPTP connections.
MAC Address
MTU
A unique hardware ID assigned to every Ethernet
adapter by the manufacturer.
Mbps
Maximum Transmission Unit is the largest packet that
can be transmitted on a packet-based network like the
internet.
Megabits per second.
Multicast
MDI
Sending data from one device to many devices on a
network.
Medium Dependent Interface is an Ethernet port for a
connection to a straight-through cable.
MDIX
Medium Dependent Interface Crossover is an Ethernet
port for a connection to a crossover cable.
MIB
NAT
Network Address Translation allows many private IP
addresses to connect to the internet, or another network,
through one IP address.
NetBEUI
Management Information Base is a set of objects that
can be managed by using SNMP.
NetBIOS Extended User Interface is a Local Area
Network communication protocol. This is an updated
version of NetBIOS.
Modem
NetBIOS
A device that modulates digital signals from a computer
to an analog signal in order to transmit the signal over
phone lines. It also demodulates the analog signals
coming from the phone lines to digital signals for your
computer.
Network Basic Input/Output System.
© 2011 CRADLEPOINT, INC.
Netmask
Determines what portion of an IP address designates the
Network and which part designates the Host.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 119
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Network Interface Card
NIC. A card installed in a computer or built onto the
motherboard that allows the computer to connect to a
network.
Network Layer
The third layer of the OSI model which handles the
routing of traffic on a network.
Network Time Protocol
Used to synchronize the time of all the computers in a
network.
NIC
routers in the network as opposed to sending the entire
routing table at a regular interval, which is how RIP
functions.
Password
A sequence of characters that is used to authenticate
requests to resources on a network.
Personal Area Network
The interconnection of networking devices within a range
of 10 meters.
Physical layer
Network Interface Card.
The first layer of the OSI model. Provides the hardware
means of transmitting electrical signals on a data carrier.
NTP
Ping
Network Time Protocol.
A utility program that verifies that a given internet
address exists and can receive messages. The utility
sends a control packet to the given address and waits for
a response.
OFDM
Orthogonal Frequency-Division Multiplexing is the
modulation technique for both 802.11a and 802.11g.
OSI
Open Systems Interconnection is the reference model for
how data should travel between two devices on a
network.
PoE
Power over Ethernet is the means of transmitting
electricity over the unused pairs in a category 5 Ethernet
cable.
POP3
OSPF
Post Office Protocol 3 is used for receiving email.
Open Shortest Path First is a routing protocol that is used
more than RIP in larger scale networks because only
changes to the routing table are sent to all the other
Port
© 2011 CRADLEPOINT, INC.
A logical channel endpoint in a network. A computer
might have only one physical channel (its Ethernet
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 120
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
channel) but can have multiple ports (logical channels)
each identified by a number.
PPP
Point-to-Point Protocol is used for two computers to
communicate with each over a serial interface, like a
phone line.
PPPoE
Point-to-Point Protocol over Ethernet is used to connect
multiple computers to a remote server over Ethernet.
PPTP
Point-to-Point Tunneling Protocol is used for creating
VPN tunnels over the internet between two networks.
Preamble
Used to synchronize communication timing between
devices on a network.
Rendezvous
Apple‘s version of UPnP, which allows for devices on a
network to discover each other and be connected without
the need to configure any settings.
Repeater
Retransmits the signal of an access point in order to
extend its coverage.
RIP
Routing Information Protocol is used to synchronize the
routing table of all the routers on a network.
RJ-11
The most commonly used connection method for
telephones.
RJ-45
QoS
The most commonly used connection method for
Ethernet.
Quality of Service.
RS-232C
RADIUS
The interface for serial communication
computers and other related devices.
Remote Authentication Dial-In User Service allows for
remote users to dial into a central server and be
authenticated in order to access resources on a network.
between
RSA
Algorithm used for encryption and authentication.
Reboot
Server
To restart a computer and reload its operating software
or firmware from nonvolatile storage.
A computer on a network that provides services and
resources to other computers on the network.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 121
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Session key
SSH
An encryption and decryption key that is generated for
every communication session between two computers.
Secure Shell is a command line interface that allows for
secure connections to remote computers.
Session layer
SSID
The fifth layer of the OSI model which coordinates the
connection and communication between applications on
both ends.
Service Set Identifier is a name for a wireless network.
Simple Mail Transfer Protocol
Used for sending and receiving email.
Simple Network Management Protocol
Governs the management and monitoring of network
devices.
SIP
Session Initiation Protocol. A standard protocol for
initiating a user session that involves multimedia content,
such as voice or chat.
SMTP
Simple Mail Transfer Protocol.
SNMP
Simple Network Management Protocol.
SOHO
Small Office/Home Office.
SPI
Stateful Packet Inspection.
© 2011 CRADLEPOINT, INC.
Stateful Packet Inspection
A feature of a firewall that monitors outgoing and
incoming traffic to make sure that only valid responses to
outgoing requests are allowed to pass though the
firewall.
Subnet mask
Determines what portion of an IP address designates the
Network and which part designates the Host.
Syslog
System Logger -- a distributed logging interface for
collecting in one place the logs from different sources.
Originally written for UNIX, it is now available for other
operating systems, including Windows.
TCP
Transmission Control Protocol.
TCP Raw
A TCP/IP protocol for transmitting streams of printer data.
TCP/IP
Transmission Control Protocol/Internet Protocol.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 122
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
TFTP
Upload
Trivial File Transfer Protocol is a utility used for
transferring files that is simpler to use than FTP but with
less features.
To send a request from one computer to another and
have a file transmitted from the requesting computer to
the other.
Throughput
UPnP
The amount of data that can be transferred in a given
time period.
Universal Plug and Play.
Traceroute
Uniform Resource Locator is a unique address for files
accessible on the internet.
A utility displays the routes between you computer and
specific destination.
URL
USB
UDP
Universal Serial Bus.
User Datagram Protocol.
UTP
Unicast
Unshielded Twisted Pair.
Communication between a single sender and receiver.
Virtual Private Network
Universal Plug and Play
VPN: A secure tunnel over the internet to connect remote
offices or users to their company‘s network.
UPnP. A standard that allows network devices to
discover each other and configure themselves to be a
part of the network.
Update
To install a more recent version of a software or firmware
product.
Upgrade
To install a more recent version of a software or firmware
product.
© 2011 CRADLEPOINT, INC.
VLAN
Virtual LAN.
Voice over IP
Sending voice information over the internet as opposed
to the PSTN
VoIP
Voice over IP.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 123
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Wake on LAN
WiFi Protected Access
Allows you to power up a computer through it‘s Network
Interface Card.
An updated version of security for wireless networks that
provides authentication as well as encryption.
WAN
Wide Area Network
Wide Area Network.
The larger network that your LAN is connected to, which
may be the internet itself, or a regional or corporate
network.
WCN
Windows Connect Now. A Microsoft method for
configuring and bootstrapping wireless networking
hardware (access points) and wireless clients, including
PCs and other devices.
Wireless (WiFi) LAN
Connecting to a Local Area Network over one of the
802.11 wireless standards.
WDS
Wireless ISP
Wireless Distribution System. A system that enables the
interconnection of access points wirelessly.
WISP. A company that provides a broadband internet
connection over a wireless connection.
Web browser
WISP
A utility that allows you to view content and interact with
all of the information on the World Wide Web.
Wireless Internet Service Provider.
WEP
Wireless Local Area Network.
Wired Equivalent Privacy is security for wireless networks
that is supposed to be comparable to that of a wired
network.
WPA
WiFi
Wireless Fidelity. Used to describe any of the 802.11
wireless networking specifications.
© 2011 CRADLEPOINT, INC.
WLAN
WiFi Protected Access. A WiFi security enhancement
that provides improved data encryption, relative to WEP.
xDSL
A generic term for the family of digital subscriber line
(DSL) technologies, such as ADSL, HDSL, RADSL, and
SDSL.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 124
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
Yagi antenna
A directional antenna used to concentrate wireless
signals on a specific location.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 125
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
10 APPENDIX
10.1 Product Information and Safety Guide
This important Product Information and Safety Guide contains safety, handling, disposal, regulatory, trademark, copyright, and software licensing information. Read all safety
information below and operating instructions before using the IBR650 3G device to avoid injury.
SAFETY AND HAZARDS
Under no circumstances should the IBR650 3G device be used in any areas (a) where blasting is in progress, (b) where explosive atmospheres may be present, or (c) that are near (i)
medical or life support equipment, or (ii) any equipment which may be susceptible to any form of radio interference. In such areas, the IBR650 3G device MUST BE POWERED OFF
AT ALL TIMES (since the device otherwise could transmit signals that might interfere with such equipment). In addition, under no circumstances should the IBR650 3G device be used
in any aircraft, regardless of whether the aircraft is on the ground or in flight. In any aircraft, the IBR650 3G device MUST BE POWERED OFF AT ALL TIMES (since the device
otherwise could transmit signals that might interfere with various onboard systems on such aircraft). Furthermore, under no circumstances should the IBR650 3G device be used by
the driver or operator of any vehicle. Such use of the device will detract from the driver or operator‘s control of that vehicle. In some jurisdictions, use of the IBR650 3G device while
driving or operating a vehicle constitutes a civil and/or criminal offense.
Due to the nature of wireless communications, transmission and reception of data by the IBR650 3G device can never be guaranteed, and it is possible that data communicated or
transmitted wirelessly may be delayed, corrupted (i.e., contain errors), or totally lost. The IBR650 3G device is not intended for, and CradlePoint recommends the device not be used in
any critical applications where failure to transmit or receive data could result in property damage or loss or personal injury of any kind (including death) to the user or to any other party.
CradlePoint expressly disclaims liability for damages of any kind resulting from: (a) delays, errors, or losses of any data transmitted or received using the device; or (b) any failure of
the device to transmit or receive such data.
Warning: This product is only to be installed by qualified personnel!
To comply with FCC/IC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain must not exceed 5 dBi in the Cellular
band and 4 dBi in the PCS band.
ANTENNA CONSIDERATIONS
Although the antenna model(s) used with these devices meet(s) the Industry Canada Radio Frequency requirements, it is possible that the future customers may swap them for
different ones without network providers knowledge and approval. Such customers must be made aware of, and follow, the Radio Frequency requirements applied in the Technical
Approval:
• RSS-102 ―Radio Frequency Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands)‖
• RSS-129 ―800 MHz Dual-Mode CDMA Cellular Telephones‖
• RSS-132e ―Cellular Telephones Employing New Technologies Operating in the Bands 824-849 MHz and 869-894 MHz‖
• RSS-133 r1 ―2 GHz Personal Communications Services‖
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 126
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
IMPORTANT NOTE
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
OPEN SOURCE SOFTWARE
This product contains software distributed under one or more of the following open source licenses: GNU General Public License Version 2, NetBSD Foundation License, and PSF
License Agreement for Python 3.1.1. For more information on this software, including licensing terms and your rights to access source code, contact CradlePoint at
www.cradlepoint.com/opensource.
WARRANTY INFORMATION
Limited 1 Year Warranty included featuring 5x12 technical support + access to software updates + hardware repair or replacement. Optional Enterprise Support Agreement available
with 24x7 technical support + software updates and upgrades + advanced hardware exchange.
CradlePoint, Inc. warrants this product against defects in materials and workmanship to the original purchaser (or the first purchaser in the case of resale by an authorized distributor)
for a period of one (1) year from the date of shipment. This warranty is limited to a repair or replacement of the product, at CradlePoint‘s discretion. CradlePoint does not warrant that
the operation of the device will meet your requirements or be error free. Within thirty (30) days of receipt should the product fail for any reason other than damage due to customer
negligence, purchaser may return the product to the point of purchase for a full refund of the purchase price. If the purchaser wishes to upgrade or convert to another CradlePoint, Inc.
product within the thirty (30) day period, purchaser may return the product and apply the full purchase price toward the purchase of another CradlePoint product. Any other return will
be subject to CradlePoint, Inc.‘s existing return policy.
LIMITATION OF CRADLEPOINT LIABILITY
The information contained in this Quick Start Guide is subject to change without notice and does not represent any commitment on the part of CradlePoint or its affiliates.
CRADLEPOINT AND ITS AFFILIATES HEREBY SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL: (A) DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL,
CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES, INCLUDING WITHOUT LIMITATION FOR LOSS OF PROFITS OR REVENUE OR OF ANTICIPATED PROFITS OR
REVENUE ARISING OUT OF THE USE OR INABILITY TO USE THE IBR650 3G DEVICE, EVEN IF CRADLEPOINT AND/OR ITS AFFILIATES HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES, AND EVEN IF SUCH DAMAGES ARE FORESEEABLE; OR (B) CLAIMS BY ANY THIRD PARTY. Notwithstanding the foregoing, in no event
shall the aggregate liability of CradlePoint and/or its affiliates arising under or in connection with the IBR650 3G device, regardless of the number of events, occurrences, or claims
giving rise to liability, exceed the price paid by the original purchaser of the IBR650 3G device.
PRIVACY
CradlePoint may collect general data pertaining to the use of CradlePoint products via the Internet including, by way of example, IP address, device ID, operating system, browser type
and version number, etc. To review CradlePoint‘s privacy policy, please visit: http://www.cradlepoint.com/privacy.
OTHER BINDING DOCUMENTS; TRADEMARKS; COPYRIGHT
By activating or using your IBR650 3G device, you agree to be bound by CradlePoint‘s Terms of Use, User License and other Legal Policies, all as posted at
www.cradlepoint.com/legal. Please read these documents carefully. CradlePoint, the CradlePoint logo, and IBR650 are trademarks of CradlePoint, Inc.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 127
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
10.2 Specifications
MODEL NAME
CradlePoint COR Integrated Broadband Router IBR650
DATA IN
3G via internal EVDO Rev. A modem, backwards compatible to
EVDO Rev 0 and 1xRTT, 10/100 Ethernet Port
DATA OUT
Two 10/100 Ethernet Ports (WAN/LAN Switchable)
ANTENNAS
2 external 3G EV-DO modem antennas
BUTTONS / SWITCHES
Power Switch, Reset
LED INDICATORS
Power, Attention, Modem, Signal Strength, Ethernet LAN, Ethernet
WAN
DIMENSIONS
3.3-in x 4-in x 0.9-in (85mm x 102mm x 22mm)
WEIGHT: 7.2 oz (200g)
CERTIFICATIONS: FCC, IC, CE, PTCRB, 802.3, plus Carrier
specific certifications
OPERATING TEMPERATURE
-10°C to 60°C (14°F to 140°F) Operating Modem as WAN
-10°C to 50°C (14°F to 122°F) Operating Ethernet as WAN
-20°C to 70°C (-4°F to 158°F) Storage
© 2011 CRADLEPOINT, INC.
DETAILS
 WAN Security NAT, SPI, ALG, inbound filtering of IP
Addresses (future), Port Blocking, Service Filtering (FTP,
SMTP, HTTP, RPL, SNMP, DNS, ICMP, NNTP, POP3,
SSH), Protocol filtering, WAN ping (allow/ignore)
 Redundancy and Load Balancing Failover/Failback with
3G/ Ethernet, Load Balancing, WAN Failure Detection via
ping
 Intelligent Routing UPnP, DMZ, Virtual Server/Port
Forwarding, Routing Rules, Route Management, Content
Filtering, Website Filtering, Local DHCP server, DHCP
Client, DNS, DNS Proxy. ALGs: PPTP, L2TP, PPPoE passthrough, IPSec pass-through, FTP (passive), FTP (active),
Dynamic DNS
 Management Remote WAN Web-based Management
Access (HTTP, HTTPS), Web-based GUI (Easy
Management), One-button firmware upgrade, USB firmware
upgrade, Modem Configuration and Management, Serverbased centralized Management (WiPipe™ Central), Modem
configuration and management
 Performance & Heath Monitoring WiPipe™ QoS, with
Traffic Shaping, SSID-based priority, WAN port speed
control
 VPN (IPSec). Device to CradlePoint, Cisco/Linksys, Linux
system, Transfer Modes, Hash (MD5, SHA128, SHA256,
SHA384, SHA512), Cipher (AES, 3DES, DES), Support for 5
concurrent connections, GRE Tunneling
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 128
CRADLEPOINT IBR650 | USER MANUAL Firmware ver. 3.3.0
http://www.cradlepoint.com/
Copyright © 2011 by CradlePoint, Inc. All rights reserved.
© 2011 CRADLEPOINT, INC.
PLEASE VISIT HTTP://KNOWLEDGEBASE.CRADLEPOINT.COM/ FOR MORE HELP AND RESOURCES
PAGE 129
Download PDF

advertising