Owner`s manual | Craftsman 137.21825 Saw User Manual

Owner's Manual
CRRFTSMRNo
2.7 HP (Maximum
10" Inch Blade
5000 R.P.M.
Developed)
TABLE SAW
Model No.
137,218250
E82443
USED 37J2
CAUTION:
•
•
•
•
•
•
Before using this Table Saw,
read this manual and follow
all its Safety Rules and
Operating Instructions.
Customer
Help
Safety Instructions
Installation
Operation
Maintenance
Parts List
EspaSol
Line
1-800-843-1682
Sears,
Roebuck
Part No. 137218250001
and Co., Hoffman
Estates,
IL 60179
USA
SECTION
PAGE
Warranty .................
°.°,lw,
,,,,,°,=,e,,,e
we
°,,°,e°2
=,.,,,,o=.,
=°,,e,°
,°e°,e,,*=.,e.
,e
e°l.°=,2
,o=.,oe.,,o
,,o°,ow
=,°,l,w,.°,e°,
°,
,e°,.°e3
°=,,°.o,e,.
e,°,lw,
..=,.oee..*..e
w=
q.°=,..=,..
.o,l.,,
.*o°.._..=,.=e
•
.°e..e,...,
,e,w,°w
*.o.e.w.,o.e,.
°.
,e,,,oo,e==
Product Specifications
......
Safety Instructions
.........
Accessories
and Attachments
Tools needed for assembly
..
Carton Contents ...........
Know Your Table Saw .....................
Assembly and Adjustments
...............
Operation
...........................
Maintenance
........................
Troubleshooting
guide ..
..............
.o.e..
.o.,i.,
•
,..eo.
.we=.le.
weg,,w,°J,w,°,.,q°,,
,Iwoe,°,l°,,*g,=*w,=
Parts .............................
_i
Making a push stick .................
Espanol ...........................
*..e...*,w.eJw,e..e.
e.,e.wee..e,=.e.w.e°
e
e,,*,,°
6
e=.w°.,
6
.w..e..6
e°e=.*.°6
,..,.o.e..,.,°
•
.*l=..*,..,..e
e
=.°..e9
.......
........
..........
..........
16
20
21
22
.........
33
e.=q°.°o...
..
el=.ei.°e=,
e°
...........
37
FULL ONE YEAR WARRANTY
If this product fails due to a defect in material or workmanship within one year from the date of purchase, Sears
will repair it free of charge.
Contact a Sears Service Center for repair.
If this product is used for commercial or rental purposes, this warranty applies only for 90 days from the date of
purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179
MOTOR
HP (Maximum developed)
......
Type .......................
Amps ......................
Voltage .....................
Hz ........................
RPM (no load) ...............
Overload Protection ...........
2.7
Universal
15
120
60
5000
YES
SAW
Table ......................
Table extension ..............
Extension fence capacity
Blade ......................
Rip scale ...................
Rip fence
..................
Miter gauge .................
Leg set .....................
Maximum Depth of cut at
Maximum Depth of cut at
Maximum Dado cut width
Net weight ..................
26-7/64" x 19-3/32"
Yes, with fence
24"
10"
YES
YES
YES
YES
3"
2-1/2"
1/2"
61.6 Lbs.
.......
90 ° ....
45 ° ....
.......
To avoid electrical hazards, fire hazards, or damage to
the tool, use proper circuit protection.
Your table saw is wired at the factory for 120V operation.
Connect to a 120V, 15 AMP branch circuit and use a 15
AMP time delay fuse or circuit breaker. To avoid shock or
fire, replace power cord immediately if it is worn, cut or
damaged in any way.
2
GENERAL SAFETY INSTRUCTIONS
12.
BEFORE USING THE TABLE SAW
Safety is a combination of common sense, staying alert
and knowing how to use your table saw.
To avoid mistakes that could cause serious injury, do not
plug the table saw in until you have read and understood
the following:
.
.
3.
4.
READ and become familiar with this entire instruction
manual. LEARN the tool's applications, limitations, and
possible hazards.
13. WEAR A FACE MASK OR DUST MASK.
Sawing operation produces dust.
KEEP GUARDS IN PLACE and in working order.
14. SECURE WORK. Use clamps or a vise to hold work
when practical. It's safer than using your hand and it
frees both hands to operate tool.
REMOVE ADJUSTING KEYS AND WRENCHES.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before
turning ON.
15. DISCONNECT TOOLS before servicing, and when
changing accessories, such as blades, bits, cutters,
and the like.
KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
16. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure the switch is in OFF position before
plugging in.
DON'T USE IN A DANGEROUS ENVIRONMENT.
Don't use power tools in damp or wet locations, or
expose them to rain. Keep work area well lighted.
5.
.
7,
17. USE RECOMMENDED ACCESSORIES. Consult the
owner's manual for the recommended accessories.
The use of improper accessories may cause risk of
injury to persons.
KEEP CHILDREN AWAY. All visitors should be kept at
a safe distance from the work area.
MAKE WORKSHOP KID PROOF with padlocks, master
switches, or by removing starter keys.
8.
DON'T FORCE THE TOOL. It will do the job better
and safer at the rate for which it was designed.
9.
USE THE RIGHT TOOL. Don't force tool or the
attachment to do a job for which it was not designed.
ALWAYS WEAR EYE
PROTECTION. Any table
saw can throw foreign
objects into the eyes which
could cause permanent eye
damage. ALWAYS wear
Safety Goggles (not glasses)
that comply with ANSI safety standard Z87.1.
Everyday eyeglasses have only impact-resistant
lenses. They ARE NOT safety glasses. Safety
Goggles are available at Sears. NOTE: Glasses or
goggles not in compliance with ANSI Z87.1 could
seriouslyhurt you when they break.
18. NEVER STAND ON TOOL. Serious injury could occur
ifthe tool is tipped or if the cuttingtool is unintentionally
contacted.
19. CHECK FOR DAMAGED PARTS. Before further use of
the tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced.
10. USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss
of power and overheating.The table on page 5 shows
the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the
heavier the cord.
20. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN THE POWER OFF. Don't leave the tool until
it comes to a complete stop:
21. DON'T OVERREACH. Keep proper footing and
balance at all times.
11. WEAR PROPER APPAREL, DO NOT wear loose
clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts.
Nonslip footwear is recommended. Wear protective
hair covering to contain long hair.
22. MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
23. DIRECTION OF FEED. Feed work into a blade or cutter
against the direction of rotationof the blade or cutter
only.
SAVE THESE INSTRUCTIONS
3
24. WARNING: Dust generated from certain materials can
be injurious to your health. Always operate saw in well
ventilated areas and provide for proper dust removal.
14. AVOID AWKWARD OPERATIONS and hand
positions where a sudden slip could cause your
hand to move into the cuffing tool.
SPECIFIC SAFETY INSTRUCTIONS
FOR THE TABLE SAW
15. NEVER
Solvents
damage
be used
ALWAYS USE SAW BLADE GUARD spreader and
anti-kickback pawls for every operation for which
they can be used, including through-sawing.
Through-sawing operations are those in which the
blade cuts completely through the workpiece
when ripping or cross-cutting.
1.
2.
ALWAYS HOLDTHE WORK FIRMLY against the
miter gauge or rip fence.
3.
USE A PUSH STICK when required. Always use a
push stick for ripping narrow stock. Refer to ripping
applications in the instruction manual where the
push stick is covered in detail. See the push stick
pattern included in this Owner's Manual.
NEVER PERFORM ANY OPERATION
"FREE HAND", which means using your hands
only to support or guide the workpiece. Always
use either the fence or the miter gauge to position
and guide the work.
4.
NEVER STAND or have any part of your body
in line with the path of the saw blade, Keep your
hands out of the line of the saw blade.
5.
6.
NEVER REACH behind or over the cutting tool
for any reason.
7.
REMOVE the rip fence when cross-cutting.
8.
DO NOT USE molding head set with this saw.
9.
FEEDWORK INTOTHE BLADE against the
direction of rotation only.
10. NEVER use the fence as a cut-off gauge when
cross-cutting.
11. NEVER ATTEMPT TO FREE A STALLED SAW
BLADE without first turning the saw OFF. Turn
power switch OFF immediately to prevent motor
damage.
12. PROVIDE ADEQUATE SUPPORT to the rear and
sides of the saw table for wide or long workpieces.
13. AVOID KICKBACKS (work thrown back towards
you) by keeping the blade sharp, keeping the rip
fence parallel to the saw btade, and by keeping the
spreader, anti-kickback pawls, and guard in place
and functioning. Do not release work before it is
pushed all the way past the saw blade. Do not rip
work that is twisted, warped, or does not have a
straight edge to guide along the fence.
USE SOLVENTS to clean plastic parts.
could possibly dissolve or otherwise
the material. Only a soft damp cloth should
to clean plastic parts.
16. MOUNT your table saw before performing any
cuffing operations. Refer to installation instructions.
17. NEVER CUT METALS or materials which may make
hazardous dust.
18. ALWAYS USE IN A WELL VENTILATED AREA.
Remove sawdust frequently. Clean out sawdust from
the interior of the saw to prevent a potential fire
hazard.
19. NEVER LEAVE THE TOOL running unattended.
Don't leave the tool until it comes to a complete stop.
20. For proper operation follow the instructions of this
owner's manual titled "SAW MOUNTED TO WORK
SURFACES" Failure to provide sawdust fall-through
and removal hole will allow sawdust to build up in
the motor area, which may result in a fire hazard or
cause motor damage.
21. ALWAYS USE THE TABLE EXTENSION for support
when cutting a long workpiece. Never use an
unstable surface or another person to hold a long
workpiece. Adjust the table extension for maximum
stability and length of the workpiece before cutting.
22. ALWAYS LOCKTHETABLE
EXTENSION securely
in place before cutting workpiece.
ELECTRICAL
REQUIREMENTS
POWER SUPPLY AND MOTOR
SPECIFICATIONS
To avoid electrical hazards, fire hazards, or damage to
the tool, use proper circuit protection. Use a separate
electrical circuit for your tools.Your saw is wired at the
factory for 120V operation. Connect to a 120V, 15 Amp
circuit and use a 15 Amp time delay fuse or circuit
breaker. To avoid shock or fire, if power cord is worn or
cut, or damaged in any way, have it replaced
immediately.
SAVE THESE INSTRUCTIONS
GROUNDING
INSTRUCTIONS
Fig. A
3-Prong Plug
IN THE EVENT OF A MALFUNCTION OR BREAKDOWN,
grounding provides a path of least resistance for electric
current and reduces the risk of electric shock, This tool
is equipped with an electric cord that has an equipment
grounding conductor and a grounding plug, The plug
MUST be plugged into a matching receptacle that is
properly installed and grounded in accordance with ALL
local codes and ordinances.
r
II
f
DO NOT MODIFYTHE PLUG PROVIDED. If it will not
fit the receptacle, have the proper receptacle installed
by a qualified electrician.
USE A SEPARATE ELECTRICAL CIRCUIT for your
tools. This circuit must not be less than #12 wire and
should be protected with a 15 Amp time delay fuse.
Before connecting the motor to the power line, make
sure the switch is in the OFF position and the electric
current is rated the same as the current stamped on the
motor nameplate. Running at a lower voltage witl
damage the motor.
This tool is intended for use on a circuit that has a
receptacle like the one illustrated in FIGURE A. FIGURE A
shows a 3-preng electrical plug and receptacle that has a
grounding conductor. If a properly grounded receptacle is
not available, an adapter (FIGURE B) can be used to
temporarily connect this plug to a 2-contact ungrounded
receptacle. The temporary adapter should be used only
until a properly grounded receptacle can be installed by
a qualified technician. The adapter (FIGURE B) has a
rigid lug extending from it that MUST be connected to a
permanent earth ground, such as a properly grounded
receptacle box. The Canadian Electrical Code prohibits
the use of adapters.
J
/
B
_
_
Properly Grounded
3-Prong Receptacle
Fig. B
Grounding Lug
IMPROPER CONNECTION of the equipment grounding
conductor can result in risk of electric shock. The
conductor with the green insulation (with or without
yellow stripes) is the equipment grounding conductor. If
repair or replacement of the electric cord or plug is
necessary, DO NOT connect the equipment grounding
conductor to a live terminal.
CHECK with a qualified electrician or service person if
you do not completety understand the grounding
instructions, or if you are not sure the tool is properly
grounded.
g Pronn
b J_
-- Make Sure This
is Connected to a
Known Ground
"_ 2-Preng
Receptacle
GUIDELINES
FOR EXTENSION
CORDS
USE ONLY 3-wire extension cords that have 3-prong
grounding plugs and 3-pole receptacles that accept
the tool's plug. Repair or replace damaged or worn
cord immediately.
USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to carry
the current your product will draw. An undersized cord will
result in a drop in line voltage and in loss of power which
will cause the tool to overheat. The table below shows the
correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier the
cord.
Be sure your extension cord is properly wired and in
good condition.Always replace a damaged extension cord
or have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
CAUTION: In all cases, make certain the receptacle is
properly grounded. If you are not sure have a qualified
electrician check the receptacle.
This tool must be grounded while in use to protect the
operator from electrical shock.
lJI I _ I 1LTJ
| | JkT_
l[14r-'l | [L_IOil _[O] ?,] =1_:4111I b?I,."_[el _. [IKI]
(when
i
This table saw is for indoor use only. Do not expose to
rain or use in damp locations.
Ampere
Rating
using
Total
=111_._ !q_-VAtLJ.
120 volts only)
length
of cord
in feet
more than
not more than
25'
50*
100'
1 SO'
O
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
16
14
12
Not
SAVE THESE INSTRUCTIONS
12
Recommended
RECOMMENDED
ACCESSORIES
UNPACKING AND CHECKING CONTENTS
Visit your Sears Hardware Department or see the
Craftsman Power and Hand Tools Catalog to purchase
recommended accessories for this power tool.
Separate all parts from packing material. Check each one
with the illustration and the list of loose parts to make
certain all items are accounted for, before discarding any
packing material.
,P_l,vlvl_,1
r,|_,II_[e
To avoid the risk of personal injury:
•
Do not use adjustable (wobble) type dadoes or
carbide tipped dado blades, maximum dado width
is 1/2".
•
•
•
Do not use a dado with a diameter larger than 6".
Do not use molding head set with this saw.
Do not modify this power tool or use accessories not
recommended by Sears.
To avoid personal injury, if any parts are missing, do not
attempt to assemble the table saw, plug in the power
cord, or turn the switch on until the missing parts are
obtained and are installed correctly.
TABLE OF LOOSE
ITEM
SAW
A.
B.
C.
Mediumscrewdriver
Adjustable wrench
#2 Phillips screwdriver
I-Illllllll
Straight edge
Ill
LI','_"'""''':',I
'_
Combination square
DESCRIPTION
E.
F.
G.
H.
I.
J.
K.
Table saw
Blade guard and splitter
Bolt, flat washer, toothed washer,
oval washer
Rip fence handle
Rip fence
Hand wheels
Dome nuts
Dado table insert
Miter gauge
Hex keys
Blade wrenches
STAND
L.
M.
N.
O.
R
Q.
Top bracket (short)
Top bracket (long)
Bottom bracket (short)
Bottom bracket (long)
Legs
Bag of bolts, nuts, foot pads
D,
TOOLS NEEDED
PARTS
A_
1
1
leach
1
1
2
2
1
1
2
2
2
2
2
2
4
1
NOTE: To make assembly easier, keep contents of box
together. Apply a coat of automobile wax to the table.
Wipe all parts thoroughly with a clean dry cloth. This will
reduce friction when pushing the workpiece.
UNPACKING
YOUR TABLE
SAW:
A.
6
B.
C.
D.
E.
G.
H.
J.
o
o l
K,
_-_
I
o
i
0
13
L.
o
o
M.
N,
O,
R
a.
Miter gauge
Blade Gl
Rip Fence
Extension table
Blade bevel scale
Rip
Blade tilting handwheel
gauge
storage
Kickback pawls
Splitter
Leg stand
Blade
Blade
Table
Splitter
bracket
Extension fence
insert
Blade bevel
lock knob
lock
handle
Blade tilt pointer
wrench
storage
Overload
reset switch
ON/OFF switch
with safety key
Blade elevation
handwheel
Power¢
Blade wrenches
holes
ASSEMBLY
INSTRUCTIONS
For your own safety, never connect plug to power source
outlet until all assembly steps are complete, and you have
read and understood the safety and operating instructions.
LEG SET (FIG. A)
1. Separate all parts and group by size and style.
NOTE: Finger tighten bolts and nuts when joining
parts.
2.
3.
4.
5.
6.
7.
8.
9.
SAW TO LEG SET (FIG. B)
1. Before mounting the blade guard, the rip fence and
miter gauge to the saw top, invert the saw table so that
it is facing the floor.
2. Position the leg set upside down on the saw base.
3. Match the holes of the stand to the holes on the
bottom flange of the saw base.
4. Secure the leg set to the saw base using bolts,
washers, and nuts.
5. When all bolts and nuts are tightened, carefully set the
saw in its upright position.
6. Position the saw on a clean, level surface.
Use bolts (1), washers (2), and nuts (3) to assemble
the leg set parts.
Attach a leg (4) to the long top bracket (5). Attach the
next leg to the opposite end of the top bracket.
Repeat this assembly for the opposite side of the
leg set.
Attach the completed leg set assemblies to the short
top brackets (6). Repeat on the opposite side.
Insert bolt (7) Lntothe recessed hole of the foot pad (8).
Insert into the leg flange hole and tighten, using
washer (9) and nut (10). Repeat for the three other
legs.
Attach the bottom brackets (11) between each leg.
Place the leg set on a level surface and tighten all
nuts and bolts.
Fig. A
Fig. B
Leg set
mounting hole
1
2
Saw base
hole
9
SAW MOUNTEDTO OTHER WORK SURFACES (FIG. C)
1. If the leg set will not be used the saw must be properly
secured to a sturdy workbench using the four mounting
holes at the base of the saw.
2. The surface of the table where the saw is to be
mounted must have a hole large enough to facilitate
sawdust fall-through and removal
3. Square the saw on the mounting surface and mark
the location of the four 3/8" mounting holes (1).
4. Drill 3/8" holes into the mounting surface.
5. Mark a 12" to 14" square (2) centered between the
four mounting holes (1).
6. Cut out and remove the square.
7. This opening will allow sawdust to fall through
the saw base.
8.
9.
Fig. D
Place the saw on the work surface, and align the
mounting holes of the saw with those drilled through
the surface.
Fasten the saw to the work surface.
Fig. C
BLADE RAISING HANDWHEEL (FIG. E, F)
1. Attach the handwheel (1) to the elevation screw (2) at
the front of the saw.
Make sure the slots (3) in the hub of the handwheel
engage with the pins (4). (FIG. E)
2. Attach and tighten the dome nut (5) at the end of the
shaft (Fig. F).
Fig. E
(__
2
Q--.m
1
3
2
4
1
BLADE TILTING HANDWHEEL (FIG. F)
1. Attach the other handwheel (6) to the blade tilting
screw on the side of the saw in the same manner
as above.
2. Attach and tighten the handwheel dome nut (5).
Failure to provide the sawdust fall-through hole will cause
sawdust to build up in the motor area, which may result
in fire or cause motor damage.
KEEPING THE AREA CLEAN (FIG. D)
1. Sawdust and wood chips that fall from under the
saw will accumulate on the floor.
2. Make it a practice to pick up and discard this dust
when you have completed cutting.
Fig. F
--5
Always keep your work area clean, uncluttered and well
lit. Do net work on floor surfaces that are slippery from
sawdust or wax.
6
10
RIP FENCE (FIG. G)
1. Thread the fence handle (1) into the cam hole (2)
until tight.
2. Lift upward on the rip fence handle so that the
holding clamp (3) is fully extended.
3. Place the rip fence on the saw table and engage
the holding clamp to the table rear. Lower the
front end onto the front rail (4).
4. Push down on the fence handle to lock.
2.
3.
4.
5.
Raise the blade arbor (4) (FIG. I) to the maximum
height by turning the blade-raising handwheel
counterclockwise.
Remove the arbor nut (5) and flange (6), remove blade.
Install the new saw blade onto the arbor with the
blade teeth pointing toward the front of the saw.
Install the flange (6) against the blade and thread the
arbor nut (5) as far as possible by hand. Ensure that
the blade is flush against the inner side of the blade
flange.
To avoid possible injury and damage to the workpiece be
sure to install the blade with the teeth pointing toward the
front of the table in the direction of the rotation arrow on
the blade guard.
4
Fig. I
6.
To tighten the arbor nut (5) place the open end
wrench jaws on the flats of the blade arbor to keep
the arbor from turning. (FIG. J)
7. Place the box-end wrench (8) on the arbor nut (5),
and turn clockwise (to the rear of the saw table.)
8. Replace the blade insert in the table recess, insert
the screws through the front and rear holes and tighten.
CHANGING THE BLADE (FIG. H, I, J)
To avoid injury from an accidental start, make sure the
switch is in the OFF position and the plug is not
connected to the power source outlet.
1.
Remove the table
screws (2, 3). Be
washer that is on
table insert. (FIG.
insert (1) by unscrewing the two
careful not to lose the rubber
the back screw (3) beneath the
H)
Fig. J
NOTE: The back screw is longer than the
front screw.
•
8
Fig. H
3
To avoid injury from a thrown workpiece, blade parts, or
blade contact, never operate saw without the proper insert
in place. Use the saw blade insert when sawing. Use the
dado head insert when using a dado.
2
11
BLADE GUARD ASSEMBLY (FIG. K, L, M)
1. Set the blade to maximum height and the tilt to zero
degrees on the bevel scale with the hand wheels.
Lock the blade lock knob.
2. Place the external toothed lock washer (1) and a
steel flat washer (2) onto the long hex. head bolt (3).
Insert the bolt into the splitter bracket (4) as shown.
(FIG. K)
Fig. M
anti-kickback pawl
S
,/
Fig. K
8
-tfl
,
I
I
I I
I
/
I
I
i
3
ADJUSTMENT
3
2
1
INSTRUCTIONS
To avoid injury from an accidental start, make sure the
switch is in the OFF position and the plug is not
connected to the power source, before making any
adjustments.
ADJUSTING THE TABLE EXTENSION
3.
4.
Place the oval washer (5) on the pivot rod (6). (FIG. L)
Install the bracket assembly (4) into the rear of the
saw table. Thread the bolt (3) into the internally
threaded pivot rod.
Fig. L
5.
6.
7.
8.
O)
NOTE: The table extension may be installed on the right
side of the table, as needed, to support long
workpieces.
NOTE: The splitter is removed from the illustration
for clarity.
6
(FIG.
5
Position the blade guard arm (7) to the rear of the
table. (FIG. M)
Using a straightedge, check that the blade guard
splitter (8) is aligned with the saw blade (9).
If straightening adjustment is necessary, loosen the
bolt (3) and shift the splitter assembly to the right or
left, or rotate.
When the splitter is properly aligned with the saw
blade, tighten the bolt.
NOTE: The splitter must always be correctly aligned
so the cut workpiece will pass on either side without
binding or twisting to the side.
12
To adjust the table extension position (FIG. O):
1. Loosen the two clamp bolts (4) on the two
extension tube brackets.
2. Slide the extension tubes in or out until the scale on
the front tube is positioned at the desired distance.
3. Tighten the two lock handles.
To adjust the extension table fence:
1. Loosen the locking handle (5) on the fence (6).
2. Raise the fence to the desired height and tighten the
locking handle.
RIP FENCE ADJUSTMENT
,_lqllll[_
To avoid injury from an accidental start, make sure
the switch is in the OFF position and the plug is
not connected to the power source outlet.
1.
2.
Fig, O
5
3.
6
(FIG. Q)
4.
5.
4
The fence (1) is moved by lifting up on the handle (2)
and sliding the fence to the desired location. Pushing
down on the handle locks the fence in position.
Position the fence on the right side of the table, and
along one edge of the miter gauge grooves.
Lock the fence handle. The fence should be parallel
with the miter gauge groove.
If adjustment is needed to make the fence parallel to
the groove, do the following:
• Loosen the two screws (3) and lift up on the handle (2).
• Hold the fence bracket (4) firmly against the front
of the saw table. Move the far end of the fence
until it is parallel with the miter gauge groove.
• Tighten both screws and push the handle to lock.
If fence is loose when the handle is in the locked
(downward) position, do the following:
• Move the handle (2) upward and turn the adjusting
screw (5) clockwise until the rear clamp is snug.
Do not turn the adjusting screw more than 1/4
turn at a time.
• Over-tightening the adjusting screw will cause
the fence to come out of alignment.
MITER GAUGE ADJUSTMENT (FIG. P)
1. Make sure that the miter gauge will slide freely through
both table grooves.
2. Loosen the lock knob (1). Set the pointer (2) to the 900
mark on the scale.
3. Make a 900 cut in a piece of scrap wood. Check cut
piece to see if it was cut at 90°. If it is not, continue to
adjust the miter gauge body (3) until the wood piece
is cut at 90 °. Refer to OPERATION section for cutting
instructions.
Fig. Q
_
il
Fig. P
RIP FENCE INDICATOR ADJUSTMENT (FIG, Q)
1. The rip fence indicator (6) points to the
measurement scale (8). The scale shows the
distance from the side of the fence to the nearest
side of the blade.
2. Measure the actual distance with a rule. If there is a
difference between the measurement and the
indicator, adjust the indicator (6).
3. Loosen the screw (7) and slide the indicator to the
correct measurement on the scale. Tighten screw
and remeasure with the rule.
o
©
2
13
To avoid injury from an accidental start, make sure the
switch is in the OFF position and the plug is not
connected to the power source outlet.
4.
Loosen the bevel lock knob; turn the tilting
handwheel to move the blade until it is 45 ° to the
table.
5.
Adjust the collar (5) so it contacts the bracket (3)
when the blade is 45 °. Tighten set screws (4).
ADJUSTING THE 90 ° AND 45 ° POSITIVE STOPS
(FIG. R, S)
Your saw has positive stops that will quickly position the
saw blade at 90 ° or 45 ° to the table. These stops were
set at the factory. Make adjustments only if necessary.
Fig. S
900 Stop
1. Disconnect the saw from the power source.
2. Turn the blade elevation handwheel and raise the
blade to the maximum elevation.
3. Loosen the blade bevel lock knob and move the
blade to the maximum vertical position. Tighten the
lock knob.
4. Place a combination square on the table and
against the blade (1') to determine if the blade
is 90° to the table. (FIG. R)
5. If the blade is not 90° to the table, loosen the two
set screws (4), located in the bottom of the table saw,
(FIG. S) with the 3mm hex key, and back off the
collar (5).
6. Loosen the bevel lock knob. Turn the blade tilting
handwheel to move the blade until it is 90 ° to the
table.
7. Adjust the collar (5) so it contacts the bracket (3)
when the blade is 90° to the table. Tighten the
two set screws (4).
345
BLADE TILT POINTER
1.
2.
NOTE: Make a trial cut on scrap wood prior to making
critical cuts. Measure for exactness.
BLADE PARALLEL TO MITER GAUGE
GROOVE (FIG. T, U)
This adjustment was made at the factory, but it should
be rechecked and adjusted if necessary.
Fig. R
90 °
When the blade is positioned at 90 °, adjust the
blade tilt pointer to read 0° on the scare.
Loosen the holding screw, position the pointer over
0 ° and tighten the screw.
45 °
1 m
To prevent personal injury:
.Always disconnect plug from the power source when
making any adjustments.
•
This adjustment must be correct or kickback could
result and accurate cuts cannot be made.
Initial adjustment (FIG.T)
1.
Remove the yellow switch key and unplug
the saw.
2.
3.
Move the blade guard out of the way.
Raise the blade to the highest position and set at
the 0° angle (90 ° straight up).
Select and mark, with a felt tip marker, a blade
tooth having a "right set".
Place the combination square base (1) into the
right side miter gauge groove (2). (FIG.T)
Adjust the rule so it touches the front marked tooth
and lock the ruler so it holds its position in the
square assembly.
Rotate the blade bringing the marked tooth to the
rear and about 1/2 inch above the table.
4.
45° Stop
1. With the blade in the upright 90 ° position, loosen the
bevel lock knob. Turn the blade tilting handwheel and
move the blade to the 45 ° position as far as it will go.
2. Place the combination square on the table as shown
in (FIG. R) to check if the blade is 45 o to the table.
3. If the blade is not 45 ° to the table, loosen the two set
screws (4) located under the table saw (FIG. S) with
a 3 mm hex key, and back off the collar (5).
5.
6.
7.
14
.
9.
Carefully slide the combination square to the rear
until the ruler touches the marked tooth.
If the ruler touches the marked tooth at the front and
rear positions, no adjustment is needed at this time.
If not, perform adjustment procedure described in
next section.
Additional blade adjustments (FIG. U)
1. If the front and rear measurements are not the
same, remove the combination square and loosen
the four adjusting screws (1) on the top of the table
about a half turn.
2. With a folded piece of cardboard covering the blade
to protect your hands, move the blade careful{y to
the left or right as much as needed to align
the blade correctly.
3. Tighten the four screws (1) and remeasure, as
described in steps 4 to 9 in the prior section.
4. If sufficient adjustment cannot be made by the four
adjusting screws (1), then also loosen the two
adjusting screws (2). Loosen these screws only
if necessary.
5. Recheck blade clearance making sure that the
blade does not hit the table insert or other parts
when at the 90 ° and 45 ° settings.
6. Tighten all screws.
Fig. T
Fig. U
15
BASIC SAW OPERATIONS
OVERLOAD PROTECTION (FIG. W)
This saw has a reset overload relay button (3) that will
restart the motor after it shuts off due to overloading or
low voltage. If the motor stops during operation, turn the
ON/OFF switch to the OFF position. Unplug the saw from
its power source. Wait about five minutes for the motor to
cool down. Push in on the reset button (3) and turn the
switch to the ON position.
RAISING THE BLADE (FIG. V)
To raise or lower the blade, turn the blade elevation
handwheel (1) to the desired blade height, and then
tighten lock handle (2) to maintain the desired blade
angle.
Fig. V
To avoid injury, the ON/OFF switch should be in the OFF
position and the plug removed from the power source while
the motor cool down takes place, to prevent accidental
starting when the reset button is pushed. Overheating may
be caused by misaligned parts or dull blade. Inspect your saw
for proper setup before using it again.
USINGTHETABLE
1
EXTENSION
(FIG. X)
2
1.
2.
TILTING THE BLADE (FIG. V)
To tilt the saw blade for bevel cutting, loosen the
lock handle (2) and turn the tilting handwheel (3). Tighten
the lock handle (2) to secure.
3.
ON / OFF SWITCH (FIG. W)
The ON / OFF switch has a removable key. With the key
removed from the switch, unauthorized and hazardous use
by children and others is minimized.
1. To turn the saw ON, insert key (1) into the slot in the
switch (2). Move the switch upward to the ON position.
2. To turn the saw OFF, move the switch downward.
3. To lock the switch in the OFF position, grasp the sides
(or yellow part) of the switch toggle (1), and pull it out.
4. With the switchkey removed, the switchwill not operate.
5. If the switch key is removed while the saw is running,
it can be turned OFF but cannot be restarted without
inserting the switch key (1).
4.
5.
6.
Remove the stop screws from the ends of the tubes.
Slide the ends of the tubes through both support
brackets on the side your workpiece will be needing
support, and replace the two stop screws.
Rotate the front tube to display the scale as an
extension of the table top scale.
Slide the extension out until the correct measurement
is displayed on the tube scale.
Loosen the fence handles, and raise or lower the
fence as needed.
Tighten all extension support handles and knobs.
Fig. X
Fig. W
I
2
16
CU'B'ING OPERATIONS
There are two basic types of cuts: ripping and
crosscutting. Ripping is cutting along the length and
the grain of the workpiece. Crosscutting is cutting
either across the width or across the grain of the
workpiece. Neither ripping nor crosscutting may be
done safely freehand. Ripping requires the use of the
rip fence, and crosscutting requires the miter gauge.
Fig.Y
Before you use the saw each and every time, check
the following:
1.
2.
3.
4.
5.
Blade is tight on the arbor.
Bevel angle lock knob is tight.
If ripping, fence knob is tight and fence is
parallel to the miter gauge grooves.
Blade guard is in place and working properly.
You are wearing safety glasses.
The failure to adhere to these common safety
rules, and those printed in the front of this manual,
can greatly increase the likelihood of injury.
6.
RIPPING (FIG.Y,Z)
To prevent serious injury:
•
Do not allow familiarity gained from the frequent use
of your table saw to cause careless mistakes.
Remember that even a careless fraction of a second
is enough to cause a severe injury.
•
Keep both hands away from the blade and path of the
blade.
•
The workpiece must have a straight edge against the
fence and must not be warped, twisted, or bowed.
1.
2.
3.
4.
5.
7.
8.
9.
Keep your thumbs off the table top. When both of your
thumbs touch the front edge of the table (2), finish the
cut with a push stick. Make a push stick using the
pattern on page 33.
The push stick (3) should always be used when the
ripped workpiece is 2" or narrower (1). (FIG. Y)
Continue pushing the workpiece with the push stick (3)
until it passes the blade guard and clears the rear of
the table.
Never pull the workpiece back when the blade is
turning. Turn the switch OFF. When the blade
completely stops raise the anti-kickback pawls on
each side of the splitter and slide the workpiece out.
Fig. Z
Remove the miter gauge. Secure the rip fence to
the table.
Raise the blade so it is about 1/8" higher than the
top of the workpiece.
Place the workpiece flat on the table and against the
fence. Keep the workpiece about 1" away from the blade.
Turn the saw ON and wait for the blade to come up
to speed.
Slowly feed the workpiece into the blade by pushing
forward only on the workpiece section (1) that will
pass between the blade and the fence. (FIG.Y)
F_k_Vg-'_l_
II_[€
AVOID KICKBACK by pushing forward only on that
section of the workpiece that will pass between the blade
and the fence.
17
BEVEL RIPPING
This cut is the same as ripping except the blade bevel
angle is set to an angle other than 0 °.
Fig. AA
2
r,._kVlV/_,1
d _,II_,[_
Cut only with the workpiece and the fence on the right
side of the blade.
RIPPING SMALL PIECES
Avoid injury from blade contact. Never make through-saw
cuts narrower than 1/2" wide.
1.
2.
It is unsafe to rip small pieces. Instead, rip a larger
piece to obtain the size of the desired piece.
When a small width is to be ripped and your hand
cannot be safely put between the blade and the
rip fence, use one or more push sticks to move
the workpiece,
CROSSCUTTING
(FIG. AA)
To prevent serious injury:
•
Do not allow familiarity gained from the frequent use
of your table saw to cause careless mistakes.
Remember that even a careless fraction of a second
is enough to cause a severe injury.
•
Keep both hands away from the blade and path of
the blade.
1
2.
3.
4,
5.
6.
BEVEL CROSSCUTTING (FIG. BB)
This cutting operation is the same as crosscutting except
the blade is at bevel angle other than 0 °.
1. Adjust the blade (1) to the desired angle, and tighten
the blade bevel lock knob.
2. Always work to the left side of the blade. The miter
gauge (3) must be in the left side groove (2). It
cannot be used in the right side groove unless the
miter angle is very sharp, as it will interfere with the
blade guard.
Fig. BB
1
Remove the rip fence and place the miter gauge in
the left side groove.
Adjust the blade height so it is 1/8" higher than the
top of the workpiece.
Hold the workpiece firmly against the miter gauge
with the blade path in line with the desired cut
location. Move the workpiece to one inch distance
from the blade.
Start the saw and wait for the blade (1) to come up to
full speed.
Keep the workpiece (2) against the face of the miter
gauge (3) and flat against the face of the gauge and
flat against the table. Then slowly push the
workpiece through the blade (FIG. Z).
Do not try to pull the workpiece back with the blade
turning. Turn the switch OFF, and carefully slide the
workpiece out when the blade is completely stopped.
,J/-------
\Pt
I.V.
]\
_-r"
h
2
COMPOUND MITER CROSSCUTTING (FIG. CC)
This sawing operation combines a miter angle with a
bevel angle.
1. Set the miter gauge (3) to the desired angle. Use
only the left side groove (2).
2. Set the blade (1) bevel to the desired angle.
3, Carefully push the miter gauge to begin the
cutting operation,
18
Fig. CC
Fig. EE
3
2
MITERING (FIG. DD)
This sawing operation is the same as crosscutting except
the miter gauge is locked at an angle other than 90 °.
1. Hold the workpiece (2) firmly against the miter
gauge (3).
2. Feed the workpiece slowly into the blade (1) to
prevent the workpiece from moving.
Fig. DD
2
1
3
USING WOOD FACING ON THE RIP FENCE (FIG. EE)
When performing some special cutting operations, add
a wood facing (1) to either side of the rip fence (2):
1. Use a smooth straight 3/4" thick wood board (1) that
is as long as the rip fence.
2. Attach the wood facing to the fence with wood
screws (3) through the boles in the fence. A wood
fence should be used when ripping material such as
thin paneling to prevent the material from catching
between the bottom of the fence and the table.
DADO CUTS (FIG. FF)
1. The dado table insert is included with this saw.
Remove the saw blade, the blade guard, and the
table insert. Install the dado and dado table insert.
2. Instructions for operating the dado are packed with
the separately purchased dado set.
3. The arbor (1) on this saw restricts the maximum
width of the cut to 1/2".
4. It is not necessary to install the outside flange (2)
before screwing on the arbor nut (3). Make sure that
the arbor nut is tight, and that at least one thread
of the arbor sticks out past the nut.
5. Use only the 6" dado set and keep the width 1/2" or
less. It will be necessary to remove the blade guard
and splitter when using dado. Use caution when
dado is operating.
6. Use onlythe correctnumber of roundoutside blades
and inside chippersas shownin the dado set'sinstruction
manual. Blade or chippermust not exceed 1/2".
7. Check saw to ensure that the dado will not strike the
housing, insert, or motor when in operation.
For your own safety, always replace the blade, blade
guard assembly, and blade insert when you are finished
with the dado operation.
Fig. FF
I
iloll
J
/2
J
\
\
"3
19
MAINTAINING
YOUR TABLE SAW
Fig. GG
GENERAL MAINTENANCE
For your own safety, turn the switch OFF and remove the
switch key. Remove the plug from the power source outlet
before maintaining or lubricating your saw.
!.
2.
3.
4.
Clean out all sawdust that has accumulated inside
the saw cabinet and the motor.
Polish the saw table with an automotive wax to keep
it clean and to make it easier to slide the workpiece.
Clean cutting blades with pitch and gum remover.
A worn, cut, or damaged power cord should be
replaced immediately.
All electrical or mechanical repairs should be attempted
only by a trained repair technician. Contact the nearest
Sears Service Center for service. Use only identical
replacement parts. Any other parts may create a hazard.
5.
Use liquid dish washing detergent and water to
clean all plastic parts.
NOTE: Certain cleaning chemicals can damage
plastic parts.
6.
Avoid use of the following cleaning chemicals or
solvents: gasoline, carbon tetrachloride, chlorinated
solvents, ammonia and household detergents
containing ammonia.
4
Place a small amount of dry lubricant such
or silicon on screw rod (1) at thrust washer
oil threads of screw rods (1). Screw rod (1)
kept clean and free of sawdust, gum, pitch,
contaminants for smooth operation.
If excessive looseness is observed in any other part of the
blade raising mechanism or tilting mechanism, take the
complete unit to a Sears Service Center.
LUBRICATION
All motor bearings are permanently lubricated at the
factory and require no additional lubrication.
On all mechanical parts of your table saw where a
pivot or threaded rod are present, lubricate using
graphite or silicone. These dry lubricants will not
hold sawdust as would oil or grease.
BLADE RAISING ANDTILTING MECHANISM (FIG. GG)
After each five hours of operation, the blade raising
mechanism and tilting mechanism should be checked for
looseness, binding, or other abnormalities. With the saw
disconnected from the power source, turn the saw
upside down and alternately pull upward and downward
on the motor unit. Observe any movement of the motor
mounting mechanism. Looseness or play in the blade
raising screw (1) should be adjusted as follows:
1.
2.
3.
as graphite
(5). Do not
must be
and other
Using a wrench, loosen nut (2).
Adjust nut (3) until it is finger-tight against the
bracket (4), then back off the nut (3) 1/6 turn.
Tighten nut (2) with the wrench, while holding nut (3)
in place. Maximum allowable play of screw rod (1)
is 4 mm.
20
TROUBLESHOOTING
GUIDE
To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power source
before making any adjustments.
• Consult your local Sears Service Center if for any reason the motor will not run.
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
Saw will not start.
1. Saw not plugged in.
2. Fuse blown or circuit breaker tripped.
3. Cord damaged.
1. Plug in saw.
2. Replace fuse or reset circuit breaker,
3. Have cord replaced by a Sears
Service Center.
Does not make
accurate 45 ° and
90 ° rip cuts.
1. Positive stop not adjusted correctly.
1. Check blade with square and adjust
positive stop.
2. Check blade with square and adjust
pointer to zero.
2. Blade tilt pointer not set accurately.
Material pinches blade
when ripping.
1. Rip fence not aligned with blade.
2. Warped wood, edge against
fence is not straight.
1. Check and adjust rip fence.
2. Select another piece of wood.
Material binds on splitter.
1. Splitter not aligned correctly
with blade.
1. Check and align splitter with blade.
Saw makes
unsatisfactory cuts.
1, Dull blade.
2. Blade mounted backwards.
3. Gum or pitch on blade.
1. Replace blade.
2. Turn blade around.
3. Remove blade and clean with
turpentine and coarse steel wool.
4. Change the blade.
5. Clean table with turpentine
and steel wool.
4. Incorrect blade for work being done.
5. Gum or pitch on table
causing erratic feed.
Material kicked back
from blade.
1,
2.
3.
4.
5.
6.
7,
Rip fence out of alignment.
Splitter not aligned with blade.
Feeding stock without rip fence.
Splitter not in place.
Dull blade.
The operator letting go of material
before it is past saw blade.
Miter angle lock knob is not tight.
1.
2.
3.
4.
5.
6.
Align rip fence with miter gauge slot.
Align splitter with blade.
Install and use rip fence.
Install and use splitter (with guard).
Replace blade.
Push material all the way past saw
blade before releasing work.
7. Tighten knob.
Blade does not
raise or tilt freely,
1. Sawdust and dirt in raising
and tilting mechanisms.
1. Brush or blow out loose dust and dirt.
Blade does not
come up to speed,
1. Extension cord too light
or too long.
2. Low house voltage.
1. Replace with adequate size cord.
Machine vibrates
excessively,
Does not make accurate
45 ° and 90 ° cross cuts.
2. Contact your electric company.
1. Saw not mounted securely to
workbench.
2. Bench on uneven floor.
1. Tighten all mounting hardware.
3. Damaged saw blade.
2. Reposition on flat level surface.
Fasten to floor if necessary.
3. Replace blade.
1. Miter gauge out of adjustment.
1. Adjust miter gauge.
21
Key aONo
Oescr,S,z.
,,on
1
2615BBDDS0
Hex head screw
M6"1.0-40
1
2501MBDN06
Flat washer
41
14212501
Spring
1
I
1
2
42
43
44
45
14910208
14910104
14903101
26218BDA18
Rear clamp
Lockingrod
Insert
Pan head screw
46
47
, 48
49
50
14962201
14962301
14960103
14962401
26378BDA70
& washer
Side cover
Upper tube
Extension wing
Scale
Truss head round
neck screw
51
19600101A2
52
53
54
14961601
2704FBD106
2651PBDK17
55
14961401
& washer
6"13-1
M6"I.0 T=6
2
3
4
5
2501MBDN06
2705FBD106
14994501
2690MZD514
Fiat washer
Nut chuck
Warning label
Rivet
6A
6
7
8
9
10
11
14912206 B1
14912206
14994103
2570DBN606
14912301
14912906
14912801
Blade guard assembly
Blade guard
Caution label
Self-locking ring
Arm
Splitter
Bush
1
1
1
2
1
1
2
12
13
14
15
16
17
14206901
14913201
14206601
14208001
2570DBN606
2615BBDD22
Roll pin
Bush
Kick back pawl
Kick back pawl
Self-locking ring
Hex head screw
& washer
1
2
2
2
2
2
M6"1.0-20
K.,P.oNo
40
S'z. 2
6 6"13-1
I
M5X0.8-12
!
1
2
M6X1.0-23
1
1
1
1
1
Locking handle
assembly
Auxiliary fence
Square nut
M6"1.0 T=5
Countersunk head M5"16-12
tapping screw
Side cover
................ ................................................................
i.......
19
20
21
22A
22
23
24
2536MBE613
14914701
14915401
14910008A1
14910008
2601BBDA40
2504MBC006
Spring pin
5-24
Damper
Caution label
Parallel bracket assembly
Parallel bracket
Hex head bolt
M6"1.0-16
External tooth
6 6
1
2
1
1
1
2
2
25
14910505
lock washer
Width body
26
14212501
28
27
29
30
15218801
14915701
18622601
2641BBDA22
31
32A
32
14961201
26028BLA25
59
60
61
19500203
2675BNHA42
14961001
& washer
Guide holder
Hex socket head
cap bolt
Clamp bolt
Pan head screw
Upper tube
1
62
63
2668BBDA23
14902909
Pan head screw
Scale
Compression spring
1
64
14902813
Table
1
1
1
1
66
65
67
2601BBDA47
14915105
2504MBC006
14916901
14911301A1
14211203
Hex
nut
Cap screw
Pointer
Round washer
M5"0.8-6
head screw
Grip
Bolt clamp assembly
Bolt clamp
1
1
1
68
69
70
71
2501NBDN16
14205001
2701FBD106
14914901
Hex head stick
bolt label
Warning
External tooth
lock washer
Fiat washer
Guard bracket
Hex. nut
Washer
33
2701FBD113
Hex. nut
M8*1.25,T=6.5
1
72
2604BBLA42
Hex socket
35
36
37
14911007
14917202
2660PBCK16
73
74
2801ABRG01
2636BBDAA9
MSX16-10
1
1
1
38
39
2536MBE627
2536MBE638
Link
Spring plate
Pan head
screw
Spring pin
Spring pin
5-30
1
1
Strain relief
Countersunk
head screw
Pan head screw
Pan head screw
Countersunk
Lead wire ass'y
Warning label
...........................................................
...... . ................................................
75
2668BDDA43
76
2668BDDA44
180 2636BBDB48
181 280655545N
182 14994601
1
3
2
1
.
_
r-
_. o
_ _1
Q._
"_
_ _ _ _1
o 3 5"
_ _r-_l
or_ =
_
_o
r_
-r
_
_
t_
_
.Q _
c'< o
--.._,<
_'_ O
_ _ _,
<__-I-n
_ 5"_ Go
_-I_11
,p
Z
=
r'
Ill
(D
_ ___>_'m
E
_ _
z
o -_'_:
-_
a, _[__
cr_ PE_m
"m
"< _D 3
_ .ocD
_¢0
.............
2.....
57
58
...............
2
_
z
c
E
m
_
_
o
_ _
M5"0.8-16
4
8
M6X1.0-20
2
2
1
M5"0.8-8
2
1
"< E_--I._
1
R ,< _-o
M6"1.0-50
6 6
1
1
1
_
114"314-1116
5"-_
c
cb_(n
-.: ¢D
_
_ o
_O--_
_ _ m
m=-.-_
-_(_
1
1
2
1
m
o o_
_ 3
_ ,<
Q
_ o._(D
Gg_b_
_ _ _
_ •
,^-r_
m
r_
{:_
m
1-
M6"1.0-25
6
_"__'_N
_)
M6* 1.0-50
1
4
_D:_u
e_._(_
C_o
_ _ o
_
=
_ ,_
.._
_lCa
1,o
M6"1.0 T=5
................................
M6"1.0-55
1
1
1
1
1
_1_
Z
22A
0
2
rm
43
42
41
40
44
27
12
13
15
5O
PJ
32A
48
52
4g
56
64
54
o_
61
_n
0
Qty
Size
Key
Part
Description
77
78A
78
79
80A
80
81
82
83
84
14916901
14911601A1
14211201
2501NBDN16
14911402A5
14911402
14608001
14911802
29835L5006
14523301
SS
86
87
260388LA38
14911707
260888LA32
Grip
8olt clamp assembly
Bolt clamp
114"3/4-1116
Flat washer
Mitre gauge assembly
Mitre gauge
Pin
Angle pointer
Steel ball
Com#
spring
0-10
M6
Hex socket set
Sheet bar
Hex socket truss
he ad so'few
88
88A
89
90
91
92
t_
93
94
95
96
97
98
99
100
14937101
14937101A2
257088N209
2536MBE605
2536MBE629
14936501
2603BBLA36
14936701
2668BBDA39
2501NBDN12
14906107
2501NBDN16
2709FBDA02
Wheel
Hand wheel assembly
E-ring
E-9
Spring pin
3-24
Spring pin
3-14
bar
Parrie ring
Hex socket set screw M6"1.0-6
Caution label
Pan head screw
M6"1.0-12
Flat washer
114"518-1116
Warning label
Flat washer
1/4"314-1/16
Hexagon nut & flat washer
1
1
1
1
1
1
I
1
1
1
1
1
2
Key Part
Description
111
112
113
114
115
116
117
18402702
2801DBHA04
14902302
14900136
14909401
26688ZDA07
2504MZC004
Dust shield
Strain relief
Switch box
Body shell
Trade mark label
Pan head screw
External tooth
lock washer
118
2853U55501
120
2653MBDE11
Size
M4"0,7-8
64
Circuit breaker
1
1
2
2
1
1
121A 2898D10G06
121 2851D55G06
screw
Rocker switch
Rocker switch element
122
123
124
125
Switch key
Needle pointer
Pan head screw
Hex nut
2
"126"'"250"i"
MBD NO8
127 14901503
128 14901103
129A 14900609A2
129 14900609
130 2703FMD108
4
1
4
2
1
4
46
286058H101
14901704
2668BBDA32
2701FBD113
131 14909001
132. 14900801
Qty
1
1
1
1
1
M5"0.8-10
1
M8*1.25,T=6.5
1
..............................
Flat washer
8X16-2.5
Pointer bracket
Height regulating bolt
Hand wheel assembly
Whee_
Crown nut
MS*l.25T=12-5
Grip
Bolt
4
2
1
1
1
3
3
1
1
1
11
22
2
2
133 14900703
Clamp handle
M10"1.5 T=8
2
134 2701FBD110
Hex nut
......................
.....................................................................
1
.............................................
135 15100801
Lock kno •_ ....................................
................
......................
11 136 2501NBDN16 Flat washer
114.314-1116
1
137
14905804
Retaining
clip
1
104 14904402
Wrench
1
183
14994701
Warning
label
1
105 2138MBL704
Wrench hex
1
106 2138MBL709
Wrench hex
107A 28078806AFA1 Power cable assembly
1
101 2707FBN107
102 14903104
107 28078B06AF
108 2801ABRF01
109 13601201
110 2660MBCE14
U-type nut
insert
Power cable
Strain relief
Cord clamp
Pan head tapping
screw
1
M4"16-16
2
r
m
\
93
B9
Ol
104
136
135
lZ9A
116/_
117
118
105
_106
109
112
111
113
k_
.,A
01
0
Key
Part No.
Description
138
14930002
Set nut
139
14930102
140
14930203
Size
Qty
Key Part No.
Description
Size
Qty
1
158
14901302
I
Arbor collar
1
159
2603BBLA66
Spring
Hex. socketsetscrewM10*l.5-12
I
Blade
1
160
2701FBD111
Hex. nut
M10"1.5 T=4
I
141 8387129942
Motor
1
161
2701FBD110
Hex. nut
M10"1.5 T=8
I
142 2620BBDC18
Pan head screw
1
162
2615BBDD25
Hex head screw
M8"1.25-16
I
M6"1.0-16
2
M5"0.8-12
& washer
143
144
14936201
14936301
& washer
I
Bearing seat
Shaft
163
14935904
2708FBD107
Stiffener
Serrated toothed
M6"1.0 T=6
1
2
147
14921307
Angle rod
1
148
14921403
Strap
6
Spring washer
Serrated toothed
6 1/4"
M6"1.0 T=6
164
165
2570BBN116
14935102
166
14935001
C-ring
Supporting
Nut
A-16
plate
1
1
Cap head square
neck bolt
6
168
14922901
6
169
2701FBD106
Spacer
Hex nut
M6"1.0 T=5
1
170
2501NBDN09
Flat washer
1/4"3/4-7/64
1
1
1
171
2502ABC417
Flat washer
6 6
1
172
2701FBD106
Hex nut
M6"1.0 T=5
1
173
2709FBDA02
Hex nut
M6"1.0
1
151
152
14921001
14921703
Plunger housing
Bracket
153
2501NBDN03
Flat washer
3/16"3/8-0.022
1
154
2617BBLC11
Hex socket head
M5"0.8-20
1
155
2501NNHN34
cap screw
Flat washer
3/8"314-5/64
2
156
14921802
Bracket
157
14901203
Saddle
M6"1.0-35
m
0_
1
1
167 2672BBDA44
hex flange nut
ro
Cap head square
neck bolt
r ...................................................................................................................
hex. flange nut
149 2502NBC406
150 2708FBD107
2672BBDA40
1
..............................................................................................................................................................................
145
146
r-
1
& flat washer
174
14920003
Motor bracket
1
14920301
2701FBD105
Spacer
Hex nut
1
1
175
176
MS*0.8T=4
1
1
177
2615BBDC25
Hex head screw
M8"1.25-16
4
and washer
178 2672BBDB50
Cap head square
neck bolt
M8"1.25-16
4
179
*
Spring pin
Owner's Manual
8-90
1
1
2536MBE621
137218250001
o
¢O
*
Not Shown
Fo
QO
fo
¢n
O
m
r-
/
m
147
(/)
148
/
149
/
/
150
138
139
r_
--4
140
153
141
167
155
169
156
171
172
164
165
166
"_
CRAFTSMAN
10" TABLE
SAW
LEG
STAND
MODEL
NO. 137.218250
PARTS LIST FOR SCHEMATIC D
Key
Part No.
Description
Size
Qty
1
17050106
Leg
2
2672BBDA54
Cap head square neck bolt
M8x1.25-16
16
3
4
17050407
2601BBDA69
Bottom support bracket (long)
Hex head bolt
L=563
M 10xl .5-20
2
4
5
14000304
Spacer (foot pad)
6
2501MBDN 11
Flat washer
7
2701FBD109
Hex nut
8
2708FBD112
Serrated toothed
9
10
17050307
2601BBDA57
Upper support bracket (short)
Hex head bolt
L=413
M8xl.5-30
2
4
11
2501MBDN08
Flat washer
68x16-2.5
4
12
17050209
Upper support bracket (long)
L=491
2
13
17050505
Bottom support bracket (short)
L=475
2
4
4
610x20-2
M10x1.5 T=8
hexagon flange nut
28
MSx1.25 T=7.5
4
4
20
CRAFTSMAN
10" TABLE
MODEL NO. 137.218250
SAW
SCHEMATIC D
<
10
11
12
9
7
6
5
4
13
3
2
29
CO
Key
Part No.
Description
Size
1
2
3
2620B8DB26
Pan head screw
MSX0.8-30
4
83871271
2603BBLA23
Support plate
Hex socket set screw
M5X0.8-8
1
2
4
87840021
Motor housing
5
83962491A1
Brush holder assembly
2ST
6
7
83990291A1
83990301
Brush assembly
Brush cover
2ST
2
8
87840081
Bearing bushing
1
9
83870111A2
Field assembly
1
10
2662MZDE41
Pan head tapping screw
11
87840131
Baffle
12
87840122A2
Armature
13
83871141
Motor nameplate
1
14
15
2801UBHA07
83871161
Strain relief bushing
Bracket
1
16
2001AH1010
Needle bearing
1
17
, ,.-
Qty
1
M5X12-60
2
23
.=
!
III
1
1
assembly
1
2570BBN117
C-ring
1
18
19
87840171
83871201
Helix gear
Collar
1
1
20
2001 LU6204
Ball bearing
21
22
83870221
2504MZF004
Bearing retainer
External tooth lock washer
64
4
23
2636BZDA07
Countersunk
M4x0.7-8
4
24
25
2571MNC252
83870253
Parallel key
Arbor shaft
6204LLU
head screw
1
1
1
1
io
CO
01
o
08
O0
01
0
32
i
\
PUSH STICK
Make from 1/2" or 3/4"
wood or thickness
less than width of
material to be cut.
c!tof
CAUTION!
Use only good
strong wood
or plywood.
Use a jigsaw or
bandsaw to
cut out.
push 1/4 wood.
o_
Cut off here to
push 1/2" wood.
J
\
Notch to help
prevent hand
from slipping.
\
1/2" Squares.
Optional
hanging hole.
For repair of major brand appliances in your own home...
no matter who made it, no matter who sold it!
1-800-4-MY-HOME
sMAnytime,
ii_ii
day or night
(1-800-469-4663)
www.sears.com
To bring in products such as vacuums,
lawn equipment and electronics
_:_:_:_!!iiii!_i
for repair, call for the location of your nearest Sears Parts & Repair Center. !!!!_!i!i!!
......
1-800-488-1222
Anytime, day or night
::::::::_:::
r:::::::_:::::
:.:*:.:.:.:.:.:
www.sears.com
_.::_::::::::,:
iii!i!iiiill
For the replacement parts, accessories and owner's manuals
that you need to do-it-yourself, call Sears PartsDirect
"_ !
1-800-366-PART
(1-800-366-7278)
6am- 11pm CST,
7 days a week
:,:4:,:::
www.sears.com/partsdirect
To purchase
ii!iiiiiiiiiiil
iiiiiiiiiiii_
or inquire about a Sears Service Agreement:
:,::::::
:._:*:.>_:,:
::_:::::::t:_:
1-800-827-6655
7 a.m. - 5 p.m. CST, Men. - Sat.
Para pedir servicio de reparacibn a dornicilio,
y para ordenar piezas con entrega a domicilio:
1-888-SU-HOGAR
s.
:.:.7:.:,:,:,:
:::+:,::,
_:_::::::::::::
:::::::_
Au Canada pour service en franc_ais: _:_:_:_:_:_..........
:::::::
1 877 LE FOYER _"
.............
::.:::.:.:
(1 877 533-6937)
(1-888-784-6427)
.... [°°'°°
!
...............
:ii_;!_!:!
::_:,:::*:
.::.:.:::.:
::::::::
:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
HomeCentral"
® Regislered T_ademark I "
© Se_rs, Roobuck and Co.
® Marca Regist rada I
TM
Trademark o€ Seam. Roebuck and Co.
Marca de F&bnca de Sears, Roebu_:k and CO.
3/2000
Download PDF

advertising