Craftsman 315.28462 Saw User Manual

PERATOR'S
MANUAL
T
10 in. TABLE SAW
Model No.
315.284620
A
WARNING: To reduce the risk of injury, the
user must read and understand the operator's
manual before using this product.
Customer
Help Line: 1-800-932-3188
Product
distributed
Hoffman
Estates,
Visit the Craftsman
987000-910
4-23-10 (REV:03)
in the United
States
by Sears
Brands
Management
IL 601 79
web page: www.craftsman.com
Save this manual
for future
reference
Corporation
[] Warranty ............................................................................................................................................................................
2
[] Introduction .......................................................................................................................................................................
2
[] General Safety Rules .....................................................................................................................................................
3-4
[] Specific Safety Rules .....................................................................................................................................................
4-5
[] Symbols .........................................................................................................................................................................
6-7
[] Electrical ............................................................................................................................................................................
8
[] Glossary of Terms ..............................................................................................................................................................
9
[] Features .....................................................................................................................................................................
10-13
[] Tools Needed ..................................................................................................................................................................
13
[] Loose Parts .....................................................................................................................................................................
14
[] Assembly ...................................................................................................................................................................
15-21
[] Operation ...................................................................................................................................................................
22-35
[] Adjustments ...............................................................................................................................................................
36-38
[] Maintenance ....................................................................................................................................................................
38
[] Accessories .....................................................................................................................................................................
39
[] Troubleshooting
.........................................................................................................................................................
39-40
[] Illustrated Parts List ...................................................................................................................................................
41-50
[] Parts Ordering/Service
CRAFTSMAN
......................................................................................................................................
Back Page
ONE YEAR FULL WARRANTY
FOR ONE YEAR from the date of purchase, this product is warranted against any defects in material or workmanship.
Defective product will receive free repair or free replacement if repair is unavailable.
For warranty coverage details to obtain repair or replacement,
This warranty does not cover the blade, which is an expendable
ranty period.
visit the web site: www.craftsman.com
part that can wear out from normal use within the war-
This warranty is void if this product is ever used while providing commercial
services or if rented to another person.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears Brands Management Corporation,
Hoffman Estates, IL 60179
This tool has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
_,
WARNING:Readand
understand
[] SECURE WORK. Use clamps or a vise to hold work
when practical. It's safer than using your hand and
frees both hands to operate tool.
[] DON'T OVERREACH. Keep proper footing and
balance at all times.
all instruc-
tions. Failure to follow all instructions listed below,
may result in electric shock, fire and/or serious
personal injury.
[] MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for better and safer performance. Follow
instructions for lubricating and changing accessories.
[] DISCONNECT TOOLS. When not in use, before
servicing, or when changing attachments, blades, bits,
cutters, etc., all tools should be disconnected.
[] AVOID ACCIDENTAL STARTING. Be sure switch is off
READ ALL INSTRUCTIONS
[] KNOW YOUR POWER TOOL. Read the operator's
manual carefully. Learn the saw's applications and
limitations as well as the specific potential hazards
related to this tool.
[] GUARD AGAINST ELECTRICAL SHOCK BY PREVENTING BODY CONTACT WITH GROUNDED
SURFACES. For example, pipes, radiators, ranges,
refrigerator enclosures.
when plugging in any tool.
[] USE RECOMMENDED ACCESSORIES.
Consult the
operator's manual for recommended accessories. The
use of improper accessories may risk injury.
[] NEVER STAND ON TOOL. Serious injury could occur
if the tool is tipped or if the cutting tool is unintentionally contacted.
[] CHECK DAMAGED PARTS. Before further use of
[] KEEP GUARDS IN PLACE and in good working order.
[] REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
[] KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents. DO NOT leave tools or
the tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting and any other conditions
that may affect its operation. A guard or other part that
is damaged must be properly repaired or replaced by
an authorized service center to avoid risk of personal
injury.
[] USE THE RIGHT DIRECTION OF FEED. Feed work
into a blade or cutter against the direction of rotation of
blade or cutter only.
[] NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN THE POWER OFF. Don't leave tool until it
pieces of wood on the saw while it is in operation.
[] DO NOT USE IN DANGEROUS ENVIRONMENTS.
Do not use power tools in damp or wet locations or
expose to rain. Keep the work area well lit.
[] KEEP CHILDREN AND VISITORS AWAY. All visitors
should wear safety glasses and be kept a safe
distance from work area. Do not let visitors contact
tool or extension cord while operating.
[] MAKE WORKSHOP CHILDPROOF with padlocks and
master switches, or by removing starter keys.
[] DON'T FORCE TOOL. It will do the job better and
safer at the feed rate for which it was designed.
[] USE RIGHT TOOL. Don't force the tool or attachment
comes to a complete stop.
[] PROTECT YOUR LUNGS. Wear a face or dust mask if
the cutting operation is dusty.
[] PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
to do a job it was not designed for. Don't use it for a
purpose not intended.
[] USE THE PROPER EXTENSION CORD. Make sure
your extension cord is in good condition. Use only a
cord heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. A
wire gauge size (A.W.G.) of at least 14 is recommended
for an extension cord 25 feet or less in length. If in
doubt, use the next heavier gauge. The smaller the
gauge number, the heavier the cord.
[] DO NOT ABUSE CORD. Never yank cord to disconnect from receptacle. Keep cord from heat, oil, and
sharp edges.
[] WHEN OPERATING A POWER TOOL OUTSIDE, USE
AN OUTDOOR EXTENSION CORD MARKED "W-A"
OR "W". These cords are rated for outdoor use and
reduce the risk of electric shock.
[] DRESS PROPERLY. Do not wear loose clothing,
gloves, neckties, or jewelry. They can get caught
and draw you into moving parts. Rubber gloves and
nonskid footwear are recommended when working
outdoors. Also wear protective hair covering to contain
long hair.
[] ALWAYS WEAR SAFETY GLASSES WiTH SIDE
SHIELDS. Everyday eyeglasses have only impactresistant lenses, they are NOT safety glasses.
3
[]
KEEP BLADES CLEAN, SHARP, AND WITH
SUFFICIENT SET. Sharp blades minimize stalling
and kickback.
[]
KEEP HANDS AWAY FROM CUTTING AREA. Keep
hands away from blades. Do not reach underneath
work or around or over the blade while blade is
rotating. Do not attempt to remove cut material when
blade is moving.
[] BLADECOASTS
AFTER
BEING TURNED OFF.
[] NEVER USE iN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
[] STAY ALERT AND EXERCISE CONTROL. Watch
what you are doing and use common sense. Do not
operate tool when you are tired. Do not rush.
[] INSPECT TOOL CORDS PERIODICALLY. If damaged,
have repaired by a qualified service technician at
an authorized service facility. The conductor with
insulation having an outer surface that is green with
or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric
cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal. Repair
or replace a damaged or worn cord immediately. Stay
constantly aware of cord location and keep it well away
from the rotating blade.
[] INSPECT EXTENSION CORDS PERIODICALLY and
[] DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
[] USE ONLY CORRECT BLADES. Do not use blades
with incorrect size holes. Never use blade washers or
blade bolts that are defective or incorrect. The maximum blade capacity of your saw is 10 in. (254 mm).
[]
[]
[]
[]
replace if damaged.
GROUND ALL TOOLS. If tool is equipped with threeprong plug, it should be plugged into a three-hole
electrical receptacle.
CHECK WITH A QUALIFIED ELECTRICIAN or service
personnel if the grounding instructions are not completely understood or if in doubt as to whether the tool
is properly grounded.
USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire
extension cords that have 3-prong grounding plugs and
3-pole receptacles that accept the tool's plug.
DO NOT MODIFY the plug provided. If it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
[] KEEP TOOL DRY, CLEAN, AND FREE FROM OiL
AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based
products, or any solvents to clean tool.
[] FIRMLY BOLT THE SAW TO A WORK BENCH OR
LEG STAND at approximately hip height.
[] NEVER OPERATE THE SAW ON THE FLOOR.
[] GUARD AGAINST KICKBACK. Kickback occurs
when the blade stalls rapidly and workpiece is driven
back towards the operator. It can pull your hand into
the blade resulting in serious personal injury. Stay out
of blade path and turn switch off immediately if blade
binds or stalls.
[] USE RiP FENCE. Always use a fence or straight edge
guide when ripping.
[] SUPPORT LARGE PANELS. To minimize risk of blade
pinching and kickback, always support large panels.
[] REMOVE ALL FENCES AND AUXILIARY TABLES
before transporting saw. Failure to do so can result in
an accident causing possible serious personal injury.
[] BEFORE MAKING A CUT, BE SURE ALL ADJUST=
MENTS ARE SECURE.
[] BE SURE BLADE PATH IS FREE OF NAILS. Inspect
for and remove all nails from lumber before cutting.
[] NEVER TOUCH BLADE or other moving parts during
use.
[] NEVER START A TOOL WHEN ANY ROTATING COM=
PONENT IS IN CONTACT WITH THE WORKPIECE.
[] DO NOT OPERATE A TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
[] WHEN SERVICING use only identical replacement
parts. Use of any other parts may create a hazard or
cause product damage.
[] USE ONLY RECOMMENDED
ACCESSORIES listed
in this manual or addendums. Use of accessories
that are not listed may cause the risk of personal
injury. Instructions for safe use of accessories are
included with the accessory.
[] DOUBLE CHECK ALL SETUPS. Make sure blade is
tight and not making contact with saw or workpiece
before connecting to power supply.
[] ALWAYS USE BLADE GUARD, SPREADER, AND
ANTI=KICKBACK PAWLS on all "through-sawing"
operations. Through-sawing operations are those in
which the blade cuts completely through the workpiece
as in ripping or cross cutting. Keep the blade guard
down, the anti-kickback pawls down, and the spreader
in place.
[] ALWAYS SECURE WORK firmly against the rip fence
or miter gauge. NEVER use the rip fence during the
same operation as the miter gauge.
[] WHEN MAKING NON=THROUGH RiP CUTS, always
use a push stick, push block, and/or featherboard so
your hands do not come within 3 inches of the saw
blade.
[] WHEN RiPPiNG NARROW STOCK, always use a
push stick, push block, or featherboard.
• NEVERperformanyoperation"freehand"which
meansusingonlyyourhandsto supportor guidethe
workpiece.Alwaysuseeithertheripfenceor miter
gaugeto positionandguidethework.
• NEVERstandor haveanypartofyourbodyin line
•
•
with the path of the saw blade.
•
•
•
•
•
•
•
NEVER reach behind, over, or within three inches of
the blade or cutter with either hand for any reason.
AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause your
hand to move into the cutting tool.
USE ONLY RECOMMENDED ACCESSORIES listed in
this manual or addendums. Use of accessories that are
not listed may cause the risk of personal injury. Instructions for safe use of accessories are included with the
accessory.
MAKE SURE THE WORK AREA HAS AMPLE LIGHTING to see the work and that no obstructions will interfere with safe operation BEFORE performing any work
using the table saw.
MOVE THE RIP FENCE out of the way when cross
cutting.
NEVER use rip fence as cutoff gauge when cross
cutting.
NEVER attempt to free a stalled saw blade without
first turning the saw OFF and disconnecting the saw
from the power source.
•
•
ALWAYS TURN OFF SAW before disconnecting it, to
avoid accidental starting when reconnecting to power
supply.
PROVIDE ADEQUATE SUPPORT to the rear and
sides of the saw table for wide or long workpieces.
AVOID KICKBACKS (work thrown back toward you)
by:
•
HOLD THE WORKPIECE
TABLE.
•
THIS TOOL should have the following markings:
a) Keeping blade sharp.
b) Keeping rip fence parallel to the saw blade.
c) Keeping spreader, anti-kickback pawls, and
blade guard in place and operating.
d) Not releasing the work before it is pushed all the
way past the saw blade using a push stick.
e) Not ripping work that is twisted or warped or
does not have a straight edge to guide along
the fence.
IF THE POWER SUPPLY CORD IS DAMAGED, it
must be replaced only by the manufacturer or by an
authorized service center to avoid risk.
FIRMLY AGAINST THE
a) Wear eye protection.
b) Use saw blade guard and riving knife/spreader/
splitter for every operation for which it can be
used, including all through sawing.
c) Keep hands out of the line of saw blade.
d) Use a push stick when required.
e) Pay particular attention to instructions
risk of kickback.
on reducing
f)
Do not perform any operation freehand.
g)
Never reach around or over the saw blade.
h) Never operate saw on floor or below waist height.
•
SAVE THESE INSTRUCTIONS.
Refer to them
frequently and use to instruct other users. If you loan
someone this tool, loan them these instructions also.
Someofthefollowingsymbolsmaybeusedonthistool•Pleasestudythemandlearntheirmeaning•
Properinterpretationofthesesymbolswillallowyouto operatethetoolbetterandsafer•
A
Safety Alert
Indicates a potential personal injury hazard•
@
Read Operator's Manual
To reduce the risk of injury, user must read and understand
operator's manual before using this product•
O
Eye Protection
Always wear eye protection with side shields marked to
comply with ANSI Z87.1.
No Hands Symbol
Failure to keep your hands away from the blade will result
in serious personal injury•
Wet Conditions Alert
Do not expose to rain or use in damp locations•
V
Volts
Voltage
A
Amperes
Current
mz
Hertz
Frequency (cycles per second)
W
Watt
Power
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic
no
No Load Speed
Rotational speed, at no load
[]
Class II Construction
Double-insulated
Per Minute
Revolutions, strokes, surface speed, orbits etc., per minute
@
@
min
•../min
of current
construction
Thefollowingsignalwordsandmeanings
areintendedto explainthe levelsof riskassociated
withthisproduct.
SYMBOL
,l_
SIGNAL
MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
CAUTION:
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
SERVICE
,_k
Servicing requires extreme care and knowledge and
should be performed only by a qualified service technician. For service we suggest you return the product to
your nearest AUTHORIZED SERVICE CENTER for repair.
When servicing, use only identical replacement parts.
WARNING:
To avoid serious personal injury, do not
attempt to use this product until you read thoroughly
and understand completely the operator's manual.
Save this operator's manual and review frequently for
continuing safe operation and instructing others who
may use this product.
,_1_ WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
EXTENSION
CORDS
SPEED
Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole receptacles that accept the
tool's plug. When using a power tool at a considerable
distance from the power source, use an extension cord
heavy enough to carry the current that the tool will draw.
An undersized extension cord will cause a drop in line
voltage, resulting in a loss of power and causing the
motor to overheat. Use the chart provided below to
determine the minimum wire size required in an extension
cord. Only round jacketed cords listed by Underwriter's
Laboratories (UL) should be used.
**Ampere
rating (on tool data plate)
0-2.0
2.1-3.4
Cord Length
3.5-5.0
5.1-7.0
7.1-12.0
12.1-16.0
Wire Size (A.W.G.)
25'
16
16
16
16
14
14
50'
16
16
16
14
14
12
100'
16
16
14
12
10
--
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
When working with the tool outdoors, use an extension
cord that is designed for outside use. This is indicated by
the letters "WA" on the cord's jacket.
Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
_IL
A
WARNING:
Keep the extension cord clear of the
AND WIRING
The no-load speed of this tool is approximately 5,000 rpm.
This speed is not constant and decreases under a load or
with lower voltage. For voltage, the wiring in a shop is as
important as the motor's horsepower rating. A line intended only for lights cannot properly carry a power tool motor.
Wire that is heavy enough for a short distance will be too
light for a greater distance. A line that can support one
power tool may not be able to support two or three tools.
GROUNDING
INSTRUCTIONS
This product must be grounded. In the event of a malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric
shock. This tool is equipped with an electric cord having
an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
_
WARNING:
Improper installation of the grounding plug can result in a risk of electric shock. When
repair or replacement of the cord is required, do
not connect the grounding wire to either flat blade
terminal. The wire with insulation having an outer
surface that is green with or without yellow stripes is
the grounding wire.
working area. Position the cord so that it will not get
caught on lumber, tools or other obstructions while
you are working with a power tool. Failure to do so
can result in serious personal injury.
Check with a qualified electrician or service personnel if
the grounding instructions are not completely understood,
or if in doubt as to whether the tool is properly grounded.
WARNING:
Check extension cords before each
use. If damaged replace immediately. Never use tool
with a damaged cord since touching the damaged
area could cause electrical shock resulting in serious
injury.
This product is for use on a nominal 120 volt circuit and
has a grounding plug similar to the plug illustrated in figure 1. Only connect the product to an outlet having the
same configuration as the plug. Do not use an adapter
with this product.
Repair or replace a damaged or worn cord immediately.
ELECTRICAL
CONNECTION
This tool is powered by a precision built electric motor.
It should be connected to a power supply that is 120
volts, AC only (normal household current), 60 Hz. Do
not operate this tool on direct current (DC). A substantial
voltage drop will cause a loss of power and the motor will
overheat. If the saw does not operate when plugged into
an outlet, double check the power supply.
,<
GROUNDING
PiN
120 V GROUNDED OUTLET
Fig. 1
Anti-KickbackPawls
(radial arm and table saws)
Push Blocks
(for jointer
planers)
A device which, when properly installed and maintained,
is designed to stop the workpiece from being kicked back
toward the front of the saw during a ripping operation.
Arbor
Device used to feed the workpiece over the jointer planer
cutterhead during any operation. This aid helps keep the
operator's hands well away from the cutterhead.
The shaft on which a blade or cutting tool is mounted.
Bevel Cut
Device used to hold the workpiece during cutting operations. This aid helps keep the operator's hands well away
from the blade.
A cutting operation made with the blade at any angle
other than 90 ° to the table surface.
Compound
Cut
A cross cut made with both a miter and a bevel angle.
Cross Cut
A cutting or shaping operation made across the grain or
the width of the workpiece.
Cutterhead
(planers and jointer planers)
A rotating cutterhead with adjustable blades or knives.
The blades or knives remove material from the workpiece.
Dado Cut
A non-through cut which produces a square-sided notch
or trough in the workpiece (requires a special blade).
Featherboard
Push Blocks
(for table saws)
Push Sticks (for table saws)
Device used to push the workpiece during cutting operations. A push stick should be used for narrow ripping
operations. The aid helps keep the operator's hands well
away from the blade.
Resaw
A cutting operation to reduce the thickness of the
workpiece to make thinner pieces.
Resin
A sticky, sap-based substance that has hardened.
Revolutions Per Minute (RPM)
The number of turns completed
one minute.
by a spinning object in
A device used to help control the workpiece by holding it
securely against the table or fence during any ripping
operation.
FPM or SPM
A cutting operation along the length of the workpiece.
Feet per minute (or strokes per minute), used in reference
to blade movement.
A metal piece, slightly thinner than the blade, which helps
keep the kerf open and also helps to prevent kickback.
Freehand
Saw Blade Path
Performing a cut without the workpiece
fence, miter gauge, or other aids.
Gum
being guided by a
A sticky, sap-based residue from wood products.
Heel
Alignment of the blade to the fence.
Kerr
The material removed by the blade in a through cut or the
slot produced by the blade in a non-through or partial cut.
Kickback
Ripping or Rip Cut
Riving Knife/Spreader/Splitter
(table saws)
The area over, under, behind, or in front of the blade. As
it applies to the workpiece, that area which will be or has
been cut by the blade.
Set
The distance that the tip of the saw blade tooth is bent (or
set) outward from the face of the blade.
Snipe (planers)
Depression made at either end of a workpiece by cutter
blades when the workpiece is not properly supported.
Through
Sawing
A hazard that can occur when the blade binds or stalls,
throwing the workpiece back toward operator.
Miter Cut
Any cutting operation where the blade extends completely
through the thickness of the workpiece.
A cutting operation made with the workpiece at any angle
to the blade other than 90 ° .
The throwing back of a workpiece usually caused by the
workpiece being dropped into the blade or being 9laced
inadvertently in contact with the blade.
Non-Through
Cuts
Any cutting operation where the blade does not extend
completely through the thickness of the workpiece.
Pilot Hole (drill presses)
A small hole drilled in a workpiece that serves as a guide
for drilling large holes accurately.
Throw-Back
Workpiece
or Material
The item on which the operation is being done.
Worktable
Surface where the workpiece rests while performing a
cutting, drilling, planing, or sanding operation.
PRODUCTSPECIFICATIONS
BladeArbor..............................................................
5/8 in.
BladeDiameter
..........................................................
10in.
BladeTilt.................................................................
0°- 45°
Rating...............................................
120V,AConly,60Hz
ANTI-KICKBACK
PAWLS
OUTFEED
SUPPORT
Input.....................................................................
15Amps
NoLoadSpeed....................................
5,000r/rain.(RPM)
CuttingDepthat0°................................................
3-1/2in.
CuttingDepthat45°..............................................
2-1/2in.
BLADE
SPREADER/ GUARD
RiViNG KNIFE
RiP
FENCE
SLiDiNGTABLE
EXTENSION
MITER
GAUGE
SCALE
FRONT
RAiL
[ABLE LOCKING
LEVER
LOCKINGLEVER
STORAGE
BRACKET(S)
BLADE
STORAGE
BEVEL
SCALE
HEIGHT/BEVEL
ADJUSTING
HANDWREEL
BEVEL
LOCKING
LEVER
SWITCH
BEVEL
INDICATOR
Fig. 2
10
KNOWYOURTABLESAW
MITER GAUGE - The miter gauge aligns the wood for
a cross cut. The easy-to-read indicator shows the exact
angle for a miter cut, with positive stops at 90 ° and 45 °.
See Figure 2.
The safe use of this product requires an understanding of
the information on the tool and in this operator's manual
as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all
operating features and safety rules.
MITER GAUGE GROOVES - The miter gauge rides in the
grooves on the saw table.
OUTFEED SUPPORT - This table extension at the back
of the tool gives the operator additional support when cutting long workpieces.
ANTI-KICKBACK
PAWLS - Kickback is a hazard in which
the workpiece is thrown back toward the operator. The
teeth on the anti-kickback pawls point away from the
workpiece. If the workpiece should be pulled back toward
the operator, the teeth dig into the wood to help prevent
or reduce the possibility of kickback.
RIP FENCE - A sturdy metal fence guides the workpiece
and is secured with the locking handle. Grooves run along
the top and sides of the rip fence for use with optional
clamps and accessories.
SCALE - Located on the front rail, the easy-to-read scale
provides precise measurements for rip cuts.
BEVEL SCALE - The easy-to-read scale on the front of
the cabinet shows the exact blade angle.
SLIDING TABLE EXTENSIONS - Located on each side
of the saw table, these table extension gives the operator
additional support when cutting wide workpieces.
BLADE - This saw is provided with a 36-tooth, 10 in.
carbide blade. The blade is raised and lowered with
the height/bevel adjusting handwheel. Bevel angles are
locked with the bevel locking lever.
_t_
WARNING"
SPREADER/RIVING KNIFE - A removable metal piece
of the blade guard assembly, slightly thinner than the saw
blade, which helps keep the kerf open and prevent kickback. When in the through sawing, or "up" position, it is
higher than the saw blade and becomes a spreader. When
in the non-through sawing, or "down" position, it is below
the saw blade teeth and becomes a riving knife.
Do not use blades rated less than the
speed of this tool. Failure to heed this warning could
result in personal injury.
BLADE GUARD - Always keep the blade guard down
over the saw blade for through-sawing cuts.
SWITCH ASSEMBLY - This saw has an easy access
power switch located below the front rail. To lock the
switch in the OFF position, remove the switch key from
the switch. Place the key in a location that is inaccessible
to children and others not qualified to use the tool.
BEVEL LOCKING LEVER - This lever, placed just under
the saw table surface on the front of the cabinet, locks the
angle setting of the blade.
HEIGHT/BEVEL ADJUSTING HANDWHEEL- Located
on the front of the cabinet, use this handwheel to lower
and raise the blade for height adjustments or blade replacement. This handwheel also makes the adjustment for
bevel angles easy.
11
OPERATINGCOMPONENTS
Theupperportionofthe bladeprojectsupthroughthe
tableandis surrounded
byaninsertcalledthethroat
plate.Theheightofthebladeissetwitha handwheel
on
thefrontofthe cabinet.Toaccommodate
widepanels,
thesawtablehasrailsoneachside.Detailedinstructions
areprovidedinthe Operation section of this manual for
A
the basic cuts: cross cuts, miter cuts, bevel cuts, and
compound cuts.
M_, WARNING:
ALWAYS make sure your workpiece is
not in contact with the blade before operating the
switch to start the tool. Failure to heed this warning
may cause the workpiece to be kicked back toward
the operator and result in serious personal injury.
WARNING:
Always
the tool is not in use
the event of a power
( O ) and remove the
tool from accidentally
The rip fence is used to position work for lengthwise cuts.
A scale on the front rail shows the distance between the
rip fence and the blade.
It is very important to use the blade guard assembly for all
through-sawing operations. The blade guard assembly
includes: riving knife/spreader/splitter, anti-kickback
pawls, and plastic blade guard.
_
remove the switch key when
and keep it in a safe place. In
failure, turn the switch OFF
key. This action will prevent the
starting when power returns.
WARNING:
To reduce the risk of accidental starting,
Always make sure the switch is in the OFF ( O ) position
before plugging tool into the power source.
POWER SWITCH
SWITCH
ON
This saw is equipped with a power switch that has a
built-in locking feature. This feature is intended to prevent
unauthorized and possible hazardous use by children and
others.
SWITCH
OFF
TO TURN YOUR SAW ON:
[] With the switch key inserted into the switch, lift the
switch button to turn ON ( I ).
TO TURN YOUR SAW OFF:
[] Press the switch button down to turn OFF ( O ).
TO LOCK YOUR SAW:
[] Press the switch button down.
[] Remove the switch key from the switch and store in a
safe, secure location.
SWITCHKEY
SWITCHIN LOCKEDPOSiTiON
Fig. 3
12
BLADES
A
For maximum performance, it is recommended that you
use the 36-tooth, 10 in. carbide-tipped combination blade
provided with your saw. Additional blade styles of the
same high quality are available for specific operations
such as ripping. Your local dealer can provide you with
complete information.
WARNING:
Do not use blades rated less than the
speed of this tool. Failure to heed this warning could
result in personal injury.
Kerf width must be within the limits stamped on the
spreader/riving knife.
_The following tools (not included or drawn to scale) are needed for assembly and making adjustments:
SCREWDRIVER
SCREWDRIVER
COMBiNATiON
SQUARE
U
AND10mmSOCKET
C-CLAMPS
Fig. 4
13
Thefollowingitemsareincludedwithyourtablesaw:
/
F
E
Fig. 5
A. Anti-Kickback
1
I. Screw .......................................................................
2
B. Blade Guard ............................................................
Pawls ...............................................
1
J. Leg Stand ................................................................
1
C. Miter Gauge .............................................................
1
K. Sliding Table Assembly ............................................
1
D. Blade Wrench ..........................................................
2
L. Dust Bag ..................................................................
1
E. Handle Assembly ....................................................
1
M. Hex Key (3 mm, 5 mm) .............................................
2
R Rip Fence ................................................................
1
N. Switch Key ...............................................................
1
G. Push Stick ...............................................................
1
O. End Plug ..................................................................
2
H. Indicator ...................................................................
1
14
UNPACKING
This product requires assembly.
[] Carefully lift saw from the carton and place it on a level
work surface.
,_
WARNING:
Do not lift the saw without help. Hold
it close to your body. Keep your knees bent and lift
with your legs, not your back. Ignoring these precautions can result in back injury.
NOTE: This tool is heavy. To avoid back injury, keep
your knees bent and lift with your legs, not your back,
and get help when needed.
_,
WARNING:
WARNING:
Never stand directly in line with the
blade or allow hands to come closer than 3 in. to the
blade. Do not reach over or across the blade. Failure
to heed this warning can result in serious personal
injury.
Do not use this product if any parts on
the Loose Parts List are already assembled to your
product when you unpack it. Parts on this list are not
assembled to the product by the manufacturer and
require customer installation. Use of a product that
may have been improperly assembled could result in
serious personal injury.
A
[] Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
MOUNTING
[] Do not discard the packing material until you have
carefully inspected the tool, identified all loose parts,
and satisfactorily operated the tool.
NOTE: Remove the foam block from between the saw's
housing and the motor by first beveling the blade (see
page 26).
[] The saw is factory set for accurate cutting. After
assembling it, check for accuracy. If shipping has
influenced the settings, refer to specific procedures
explained in this manual.
[] If any parts are damaged or missing, please call
1-800-932-3188 for assistance.
A
A
A
WARNING:
To avoid serious personal injury, always
make sure the table saw is securely mounted to a
workbench or an approved leg stand. NEVER operate the saw on the floor.
HOLES
The table saw must be mounted to a firm supporting
surface such as a workbench or leg stand. If bolted to
a workbench, remove the four locking knobs. Four bolt
holes have been provided in the saw's base for this purpose. Each of the four mounting holes should be bolted
securely using 3/8 in. machine bolts, lock washers, and
hex nuts (not included). Bolts should be of sufficient
length to accommodate the saw base, lock washers, hex
nuts, and the thickness of the workbench. Tighten all four
bolts securely.
Carefully check the workbench after mounting to make
sure that no movement can occur during use. If any tipping, sliding, or walking is noted, secure the workbench to
the floor before operating.
WARNING:
If any parts are damaged or missing, do
not operate this tool until the parts are replaced. Use
of this product with damaged or missing parts could
result in serious personal injury.
TO ASSEMBLE
THE LEG STAND
See Figures 6- 7.
NOTE: Do not use this leg stand with other equipment or
for other purposes.
WARNING:
Do not attempt to modify this tool
or create accessories not recommended for use
with this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
[] Place the leg stand on the floor.
[] Keeping fingers and all body parts away from the
stand's moving parts, open the leg stand by pushing
opposite legs in opposite directions as indicated by the
arrows in figure 6. The stand will be fully opened when
the red indicator rests in the V slot of the grip.
WARNING:
Do not connect to power supply until
assembly is complete. Failure to comply could result
in accidental starting and possible serious personal
injury.
NOTE: Only mount the saw when the stand is
completely opened.
15
1
LOCKING
KNOB
HOLE
iNDiCATOR
V SLOT
Fig. 6
Fig. 8
TO INSTALL
THE HANDLE
See Figure 9.
[]
Hold the nylon nut securely and turn the screw
counter- clockwise to remove the nut completely.
NOTE: Do not remove the screw from the handle.
[]
Place the nylon nut into the recessed hole on the back
of the height/bevel adjusting handwheel and hold in
place.
Slide the handle and screw into the hole on the
[]
Fig. 7
[]
MOUNTING
height/bevel adjusting handwheel.
Using a flathead screwdriver, turn the screw clockwise
and tighten in place.
THE TABLE SAW BASE TO THE
LEG STAN D
See Figure 8.
[] Place the table saw base on the leg stand. Position the
locking knob over the holes in the top of the leg stand.
NUT
[] Insert the screw on the locking knob into the hole and
turn the locking knob clockwise to secure the table saw
base to the leg stand.
[] Repeat with the other three locking knobs.
HANDLE
SCREW
HEIGHT/BEVEL
ADJUSTING HANDWHEEL
16
Fig. 9
TO REMOVE/REPLACETHETHROATPLATE
To place in riving knife position (or "down" position for all
non-through cutting):
[] Remove the throat plate.
See Figure 10.
[] Lower the blade by turning the height/bevel adjusting
handwheel counterclockwise.
[] Raise the saw blade by turning the height/bevel
ing handwheel clockwise.
[] To remove the throat plate, place your index finger in
the hole and lift the front end pulling the throat plate
out toward the front of the saw.
adjust-
[] Unlock the release lever by pulling it up.
[] Push the riving knife down until it is below the saw
blade.
[] To reinstall the throat plate, slip the tab into the slot at
the back of the saw and push down to secure in place.
[] Lock the release lever by pushing the lever down.
[] Reinstall the throat plate.
PLATE
_(U
SPREADER/
RiViNG KNIFE
RELEASE
LEVER
NLOCKED)
10
TO CHANGE BETWEEN
RIVING KNIFE
A SPREADER
AND A
IN "UP" POSITIONFORTHROUGHCUTTING
See Figure 11.
RELEASE
LEVER
This saw is shipped with the spreader/riving knife placed
in the non-through cutting or "down" position (riving knife
position).
NOTE: The spreader/riving knife must be placed in the
through cutting, or "up" position (spreader position), for all
other cutting operations.
[] Unplug the saw.
To place in spreader position (or "up" position for all
through cutting):
[] Remove the throat plate.
[] Raise the saw blade by turning the height/bevel
ing handwheel clockwise.
adjust-
[] Unlock the release lever by pulling it up.
[] Grasp the spreader and pull it towards the right side of
the saw to release the spreader from the spring-loaded
riving clamp.
IN "DOWN" POSITIONFOR NON-THROUGHCUTTING
Fig. 11
[] Pull the spreader up until the internal pins are engaged
and the spreader is above the saw blade.
[] Lock the release lever by pushing the lever down.
[] Reinstall the throat plate.
17
TO CHECK
SAW BLADE
TO iNSTALL
iNSTALLATiON
THE ANTI-KICKBACK
CAUTION: To work properly, the saw blade teeth must
point down toward the front of the saw. Failure to do so
could cause damage to the saw blade, the saw, or the
workpiece.
_IL
AND
WARNING:
Replace dull or damaged anti-kickback
pawls. Dull or damaged pawls may not stop a kickback increasing the risk of serious personal injury.
[]
Unplug the saw.
[]
Lower the saw blade and remove the throat plate.
CutS.
[]
Make sure the bevel locking lever is securely pushed to
the left, see Figure 14. Raise the saw blade to its full
height by turning the height/bevel adjusting handwheel
clockwise.
[] Unplug the saw.
[] Place spreader/riving
PAWLS
BLADE GUARD
See Figures 13- 15.
See Figure 12.
Anti-kickback
pawls should only be installed for through
[] Raise the saw blade by turning the height/bevel
ing handwheel clockwise.
[] Place spreader/riving
knife in "up" position.
adjust-
knife in "up" position.
To install anti-kickback
pawls:
[] Press and hold the button on the right side of the antikickback pawls.
To loosen the blade:
[] Remove the blade wrench from the blade wrench storage area.
PAWL
HANDLE
[] Using blade wrenches, place the flat open end of a
blade wrench on the flats on the arbor shaft.
BUTTON
[] Insert the closed end of the blade wrench over the
blade nut. Holding both wrenches firmly, pull the
wrench (right side) forward to the front of the machine.
To tighten the blade:
[] Using the blade wrench, place the fiat open end into
the flats on the arbor shaft.
[] Insert the closed end of the blade wrench over the
blade nut. Holding both wrenches firmly, push the
wrench (right side) to the back of the machine. Make
sure the blade nut is securely tightened. Do not overtighten.
ANTI-KICKBACK
PAWLS
[] Reinstall the throat plate.
[] Check all clearances for free blade rotation.
BLADE
WRENCH
BLADE
WRENCH
Fig. 13
BLADE
GUARD
LEVER
LEVER
|
Fig. 12
Fig. 14
18
[] Aligntheslotinthe pawlsoverthe rearholeinthe
spreader/riving
knife.
[] Pushthe pawlhandledownsnappingthemintoplace
andreleasethe button.
NOTE:Pullonthepawlhandleto makesurepawlsare
securelylocked.
Toinstal( b(ade guard:
[] The saw blade and spreader/riving knife are aligned
when the framing square contacts both the blade and
spreader/riving knife evenly with no gaps.
If the spreader/riving knife is out of alignment with the saw
blade, adjustment is needed. The spreader/riving knife
must be in alignment front to back (horizontally) and top to
bottom (vertically).
To adjust (horizontally):
[] Lift the guard lever up to unlock.
[] With the front of the blade guard raised, lower the
back of the guard into the middle hole of the spreader/
riving knife. Push the front of the guard down until it is
parallel to the table (see figure 15). If the blade guard
is not parallel to the table, the riving knife is not in the
spreader (or "up") position.
[] Remove the anti-kickback
assembly.
pawls and blade guard
[] Lock the guard in place by pushing the guard lever
down.
[] Once properly aligned, securely retighten all screws.
[] Loosen the screws holding the mounting bracket.
[] Reposition the spreader/riving knife left or right as
needed to align the spreader/riving knife with the saw
blade.
To adjust (vertically):
NOTE: Blade alignment with the spreader can be adjusted
for different blade widths. Refer to: To Check and Align the
Spreader/Riving Knife and Saw Blade. Check the blade
guard assembly for clearances and free movement.
[] Slowly turn the set screws until the riving knife is
aligned with the blade.
HORIZONTAL ADJUSTMENT
FRAMING
SQUARE
i
I
SCREW__
SPREADER/
RIVING KNIFE
CORRECT
BLADE _
tl_
VERTICALADJUSTMENT
INCORRECT
TO CHECK
AND ALIGN
Fig. 15
THE SPREADER/RIVING
KNIFE AND SAW BLADE
See Figure 16.
To check a(ignment
of the spreader/riving
SET
SCREW
knife:
[] Unplug the saw.
[] Raise the saw blade by turning the height/bevel
ing handwheel clockwise.
I
adjustSPREADER/
RiViNG KNIFE
[] Remove the anti-kickback pawls and blade guard
assembly. Place a framing square or straight edge
against both the saw blade and the spreader.
BLADE _.
NOTE: Place framing square between carbide teeth
and measure from blade. This step will insure framing
square is square against blade from the front to back of
blade.
m
Fig. 1 6
19
TO ASSEMBLE
THE SLIDING
TABLE
SCREW
ASSEMLBY
See Figures 17- 18.
%
REAR
EXTENSIONROD
(
To install s(iding table extension:
[] Locate the sliding table assembly.
[] Unlock the front and back table locking levers.
[] Insert sliding table assembly into table locking levers.
[] Push the table assembly until it rests against the saw
table and is completely closed.
[] Install phillips head screw into hole at end of the rear
extension rod to hold sliding table assembly into locking levers.
SLIDING
TABLE
ASSEMBLY
[] Lock the front and back table locking levers.
Fig. 17
To install indicator:
[] Locate the indicator.
[] Slip the indicator in the slot on the front rail. Fit the top
slot in the indicator over the detent on the end plug
and the bottom slot over the screw hole on the end
plug.
_
[] Insert a screw into the bottom slot of the indicator, the
hole in the end plug and the extension rod. Tighten securely, but do not overtighten. Overtighting may crush
extension rod ends.
DETENT
SCREWHOLE
/
INDICATOR
ENDPLUG
EXTENSION
ROD
TABLE
LOCKING
LEVER
SCREW
20
Fig. 18
TO INSTALL
DUST
BAG
See Figure 19.
[] Slide the elbow inside the dust chute on the back of
the table saw.
NOTE: For efficient operation, empty the dust bag before
it is half full. This will permit better air flow through the
bag.
BLADE
WRENCHES
DUST
ELBOW
Fig. 20
DUST
BAG
PUSH
STICK
MITER
GAUGE
Fig. 19
TO STORE THE TABLE
See Figures 20 - 21.
SAW ACCESSORIES
STORAGE
HOOK
The table saw has two convenient storage areas (one on
either side of the saw cabinet) specifically designed for
the saw's accessories.
When not in use, store the accessories securely by snapping each accessory in place.
RiP
FENCE
Fig. 21
21
A
A
A
WARNING:
Do not allow familiarity with tools
to make you careless. Remember that a careless
fraction of a second is sufficient to inflict severe
Kickback can be caused by any action that pinches the
blade in the wood such as:
injury.
[] Sawing into knots or nails in the workpiece
[] Twisting the wood while making a cut
WARNING:
Always wear eye protection with side
shields marked to comply with ANSI Z87.1. Failure to
do so could result in objects being thrown into your
eyes, resulting in possible serious injury.
[] Failing to support work
[] Forcing a cut
[] Cutting warped or wet lumber
[] Using the wrong blade for the type of cut
[] Not following correct operating procedures
WARNING:
Do not use any attachments or
accessories not recommended by the manufacturer
of this tool. The use of attachments or accessories
not recommended
injury.
A
[] Making a cut with incorrect blade depth
[] Misusing the saw
[] Failing to use the anti-kickback
[] Cutting
blade
can result in serious personal
AVOIDING
You may use this tool for the purposes listed below:
KICKBACK
[] Always use the rip fence when rip cutting. Use the
miter gauge when cross cutting. This helps prevent
twisting the wood in the cut.
[] Straight line cutting operations such as cross cutting,
ripping, mitering, beveling, and compound cutting
[] Always use clean, sharp, and properly-set
Never make cuts with dull blades.
[] Dado with optional accessories
[] Cabinet making and woodworking
blades.
[] To avoid pinching the blade, support the work properly
before beginning a cut.
NOTE: This table saw is designed to cut wood and wood
composition products only.
[] When making a cut, use steady, even pressure. Never
force cuts.
OF THE TABLE SAW
The 3-prong plug must be plugged into a matching outlet
that is properly installed and grounded according to all
local codes and ordinances. Improper connection of the
equipment can result in electric shock. Do not modify
the plug if it will not fit the outlet. Have the correct outlet
installed by a qualified electrician. Refer to the E(ectrica(
section in this manual.
CAUSES
set
[] Inspect the work for knots or nails before beginning a
cut. Knock out any loose knots with a hammer. Never
saw into a loose knot or nail.
APPLICATIONS
OPERATION
or improperly
[] Always use the correct blade depth setting. The top of
the blade teeth should clear the workpiece by 1/8 in. to
1/4 in.
WARNING:
Although many of the illustrations in
this manual are shown with the blade guard removed
for clarity, do not operate the saw without the blade
guard unless specifically instructed to do so.
BASIC
pawls
with a dull, gummed-up,
[] Do not cut wet or warped lumber.
[] Use extra caution when cutting some prefinished or
composition wood products as the anti-kickback pawls
may not always be effective.
[] Always guide your workpiece with both hands or with
push sticks and/or push blocks. Keep your body in a
balanced position to be ready to resist kickback should
it occur. Never stand directly in line with the blade.
OF KICKBACK
Kickback can occur when the blade stalls or binds, kicking the workpiece back toward you with great force and
speed. If your hands are near the saw blade, they may
be jerked loose from the workpiece and may contact the
blade. Kickback can cause serious injury. Use precautions
to avoid the risks.
[] Use of a featherboard will help hold the workpiece
securely against the saw table or fence.
[] Clean the saw, blade guard, under the throat plate, and
any areas where saw dust or scrap workpieces may
gather.
[] Use the right type of blade for the cut being made.
[] Always use the spreader / riving knife for every
operation where it is allowed. The use of this device
will greatly reduce the risk of kickback.
22
CUTTINGAIDS
See Figure 22.
Push sticks are devices that may be used for pushing a
workpiece through the blade in any rip cut. When making non-through cuts or ripping narrow stock, always use
a push stick, push block, and/or featherboard so your
hands do not come within 3 inches of the saw blade.
They can be made in various sizes and shapes from scrap
wood and used in a specific project. The stick must be
narrower than the workpiece, with a 90 ° notch in one end
and shaping for a grip on the other end.
31/2in.
A push block has a handle fastened by recessed screws
from the underside. Use push blocks for narrow cuts and
all non-through cuts.
3/4in..
Fig. 23
CAUTION: Be sure the screws in a push block are
recessed to avoid damaging the saw or workpiece.
HOW TO MAKE A JIG (FOR RIP CUTTING
NARROW WORKPIECE)
See Figure 24.
If ripping a narrow workpiece places the hands too close
to the blade, it will be necessary to make and use a jig.
To make a jig:
[] Attach a handle to a long, straight piece of wood and
secure from the underside using recessed screws.
[] Cut an L-shaped stop in the side of the jig.
To use a jig:
[] Position the workpiece flat on the table with the edge
flush against the jig and against the stop.
[] Holding the jig handle and using a push block and/or
push stick, make the rip cut as described on page 31
later in this section.
PUSH BLOCKS
Fig. 22
AUXILIARY
STOP
FENCE
An auxiliary fence is a device used to close the gap between the rip fence and the saw table. Always make and
use and auxiliary fence when ripping material 1/8 in. or
thinner.
HOW TO MAKE AND ATTACH
FENCE (FOR RIP CUTTING
See Figure 23.
JIG
HANDLE
AN AUXILIARY
THIN WORKPIECE)
Rip fence holes are used to secure an auxiliary fence
which requires a piece of wood 3/4 in. thick, 3-1/2 in.
wide, and 21 in. long to make.
JIG
To attach the auxiliary fence to the rip fence:
[] Place the wood against the rip fence and resting firmly
on the saw table.
[] From the back side of the rip fence, secure the wood to
the fence using 1-3/4 in. wood screws.
Fig. 24
23
FEATHERBOARD
Afeatherboard
is a deviceusedto helpcontrolthe
workpieceby holdingit securelyagainstthetableor
fence.Featherboards
areespeciallyusefulwhenripping
smallworkpieces
andforcompletingnon-through
cuts.
Theendis angledwitha numberofshortkerfsto givea
frictionholdontheworkpieceandlockedinplaceonthe
tablewitha C-clamp.Testto ensureit canresistkickback.
HOWTO MAKEA FEATHERBOARD
See Figure 25.
The featherboard is an excellent project for the saw.
Select a solid piece of lumber approximately 3/4 in. thick,
2-1/2 in. wide and 12 in. long. Mark the center of the
width on one end of the stock. Miter the width to 70 ° (see
page 31 for information on miter cuts).
Prepare the saw for ripping as discussed on page 31. Set
the rip fence to allow approximately a 1/4 in. "finger" to be
cut in the stock. Feed the stock only to the mark previously made at 6 in. Turn the saw OFF and allow the blade
to completely stop rotating before removing the stock.
Reset the rip fence and cut spaced rips into the workpiece
to allow approximately 1/4 in. fingers and 1/8 in. spaces
between the fingers.
A
AL
WARNING:
Mount the featherboard
in front of the
saw blade. If positioned improperly, kickback can
result from the featherboard pinching the workpiece
and binding the blade in the saw ken:. Failure to heed
this warning can result in serious personal injury.
HOW TO MOUNT
See Figure 26,
A FEATHERBOARD
Completely lower the saw blade. Position the rip fence to
the desired adjustment for the cut to be performed and
lock. Place the workpiece against the fence and over the
saw blade area. Adjust the featherboard to apply resistance to the workpiece just forward of the blade. Securely
tighten the adjusting clamp knob to secure the featherboard in place. Attach C-clamps to further secure the
featherboard to the edge of the saw table.
PUSH
BLOCK
PUSH
STICK
FEATHERBOARD
BEVELLOCKING
LEVER
Fig. 26
1
I [
|
|
|
2-1/2in.
1/4 in.
o| 1-1/16in.
_1
I
|
1/8 in.
3/4in.
12 in.
Fig. 25
24
TYPESOF CUTS
See Figure 27,
©
There are six basic cuts: 1) the cross cut, 2) the rip cut, 3)
the miter cut, 4) the bevel cross cut, 5) the bevel rip cut,
and 6) the compound (bevel) miter cut. All other cuts are
combinations of these basic six. Operating procedures for
making each kind of cut are given later in this section.
WARNING:
CROSSCUT
Always make sure the blade guard
©
and anti-kickback pawls are in place and working
properly when making these cuts to avoid possible
injury.
Cross cuts are straight 90 ° cuts made across the grain of
the workpiece. The wood is fed into the cut at a 90 ° angle
to the blade, and the blade is vertical.
Rip cuts are made with the grain of the wood. To avoid
kickback while making a rip cut, make sure one side of the
wood rides firmly against the rip fence.
Miter cuts are made with the wood at any angle to the
blade other than 90 ° . The blade is vertical. Miter cuts tend
to "creep" during cutting. This can be controlled by holding the workpiece securely against the miter gauge.
Bevel cuts are made with an angled blade. Bevel cross
cuts are across the wood grain, and bevel rip cuts are with
the grain.
Compound (or bevel) miter cuts are made with an angled
blade on wood that is angled to the blade. Be thoroughly
familiar with making cross cuts, rip cuts, bevel cuts, and
miter cuts before trying a compound miter cut.
CUTTING
TiPS
Dado and rabbet cuts are non-through cuts which can
be either rip cuts or cross cuts. Carefully read and understand all sections of this operator's manual before attempting any operation.
WARNING:
Do not use blades rated less than the
speed of this tool. Failure to heed this warning could
result in personal injury.
[] The kerf (the cut made by the blade in the wood) will be
wider than the blade to avoid overheating or binding.
Make allowance for the kerf when measuring wood.
[] Make sure the kerf is made on the waste side of the
_ND
Fig. 27
measuring line.
[] Cut the wood with the finish side up.
[] Knock out any loose knots with a hammer before making
the cut.
[]
(BEVEL)MITERCUT
Always provide proper support for the wood as it comes
out of the saw.
25
TO CHANGEBLADE DEPTH
TO ADJUST
See Figure 28.
See Figure 30.
If the bevel indicator is not at zero when the saw blade
The blade depth should be set so that the outer points of
the blade are higher than the workpiece by approximately
1/8 in. to 1/4 in. but the lowest points (gullets) are below
the top surface.
THE BEVEL
INDICATOR
is at 90 ° , adjust the indicator by loosening the screw and
setting it at 0 ° on the bevel scale. Retighten the screw.
[] Raise the blade by turning the height/bevel adjusting
handwheel clockwise or lower it by turning the handwheel counterclockwise.
LJ
GULLET
BEVEL
LOCKING
LEVER
HEIGHT/BEVEL
ADJUSTING
HANDWHEEL
SCREW
Fig. 28
TO CHANGE BLADE
See Figured 29 - 30.
ANGLE
(BEVEL)
BEVEL
INDICATOR
NOTE: A 90 ° cut has a 0 ° bevel and a 45 ° cut has a 45 °
bevel.
[] Loosen bevel control by pulling the bevel locking lever
all the way to the right.
[] Adjust the bevel angle by pushing the wheel in toward
the saw then turning it. Turning the wheel counterclockwise increases the angle of the blade, bringing it
closer to 45 ° . Turning it clockwise decreases the angle,
bringing the blade closer to 90 ° .
[] Tighten bevel control by pushing the bevel lock lever to
the left.
ANGLE
ODECREASE
ANGLE
Fig. 29
Fig. 30
26
A
WARNING:
To reduce the risk of injury, always
make sure the rip fence is parallel to the blade before
beginning any operation.
CLAMP
TO USE THE RIP FENCE
LOCKING
LEVER
See Figure 31.
[] Place the rear lip on the rear of the saw table and pull
slightly toward the front of the unit.
[] Lower the front end of the rip fence onto the guide
surfaces on top of the front rail.
[] With the rip fence flat on the saw table, push the fence
towards the front rail to align the fence to the saw
table.
REAR
LiP
[] Push the locking lever down to align and secure the
fence.
Check for a smooth gliding action. If adjustments are
needed, see To Check the Alignment of the Rip Fence
to the Blade in the Adjustment section of this manual.
RiP
FENCE
BLADE
SCALE
[] Make two or three test cuts on scrap wood. If the cuts
are not true, repeat the process.
NOTE: The rip fence must be secure when the locking
handle is engaged. To increase the grip of the rip fence
on the rear lip of the table, tighten the clamp screw on
the rear of the rip fence by turning it clockwise.
TO SET THE RIP FENCE
THE BLADE
SCALE
iNDiCATOR
TO
See Figure 31.
Use the indicator on the rip fence to position the fence
along the scale on the front rail.
NOTE: The anti-kickback pawls and blade guard assembly must be removed to perform this adjustment. Reinstall
the blade guard assembly when the adjustment is complete.
FRONT
RAIL
Begin with the blade at a zero angle (straight up).
SCALE
INDICATOR
[] Unplug the saw.
[] Loosen the rip fence by lifting the locking lever.
LOCKING
LEVER
Fig. 31
[] Using a framing square, set the rip fence 2 in. from the
blade tip edge.
[] Loosen the screw on the scale indicator and align with
the 2 in. mark as shown.
[] Tighten the screw and check the dimension and the rip
fence.
27
TO USE THE MITER
GAUGE
TO USE THE SLiDiNG
TABLE
EXTENSION
See Figure 32.
See Figure 34.
The miter gauge provides greater accuracy in angled cuts.
For very close tolerances, test cuts are recommended.
Increase the length of the saw table by using the table
extension.
There are two miter gauge grooves, one on either side
of the blade. When making a 90 ° cross cut, you can use
either miter gauge groove. When making a beveled cross
cut (the blade tilted in relation to the table) the miter gauge
should be located in the groove on the right so that the
blade is tilted away from the miter gauge and your hands.
[] Set the rip fence to 15 in.
[] Pull the front table locking lever toward you to unlock
the lever. Repeat with the back lever.
[] Slide the table extension to the desired width.
NOTE: Use the scale on the front rail when a specific
width is desired.
The miter gauge can be turned 60 ° to the right or left.
[] Once the extension table are set to the desired width,
relock the front and back locking levers by pushing the
levers back towards the saw base.
[] Loosen the lock knob.
[] With the miter gauge in the miter gauge groove, rotate
the gauge until the desired angle is reached on the
scale.
SLIDINGTABLE
EXTENSION
[] Retighten the lock knob.
MITER
GAUGE BODY
LOCK
KNOB
TABLE
LOCKING
LEVER
MITER
GAUGE
Fig. 32
TO USE THE MITER
TION
GAUGE
iN A REVERSE
Fig. 34
POSl=
TO USE THE OUTFEED
See Figure 35.
See Figure 33.
SUPPORT
For larger workpieces, the miter gauge can be reversed in
the miter gauge grooves. It will be necessary when reversing the miter gauge to securely clamp the workpiece to
the miter gauge body.
The outfeed support slides to give the operator additional
support for cutting long workpieces.
NOTE: After clamping the wood against the miter gage
face, it must rest flat against both the saw table and miter
gauge faces.
[] Grasp the outfeed support with both hands and pull it
until it is fully extended.
[] With the table saw in the OFF position, stand behind
the saw.
OUTFEED
SUPPORT
MITER GAUGE
REVERSED
\
Fig. 35
Fig. 33
28
HEELING(PARALLELING)
THE BLADE
ADJUSTING
TO THE
MITER GAUGE GROOVE
See Figures 36 - 38.
_
_ll
U/
WARNING:
The blade must be parallel to the miter
gauge groove so the wood does not bind resulting
in kickback. Failure to do so could result in serious
personal injury.
SCREWS(2)
"
_
_
_
RIGHTMITER
I_ GAUGE GROOVE
/
i//
Do not loosen any screws for this adjustment until you
have checked with a square and made test cuts to be
sure adjustments are necessary. Once the screws are
loosened, these items must be reset.
SQUARE
.........................................
, F------),
[] Unplug the saw.
[] Remove the blade guard and anti-kickback pawls.
Raise the blade by turning the height/bevel adjusting
handwheel.
i
[] Mark beside one of the blade teeth at the front of the
blade. Place a combination square even with the front
of the saw table and the side of the saw blade as
shown in figure 36.
[]
Turn the blade so the marked tooth is at the back.
[]
Move the combination square to the rear and again
measure the distance. If the distances are the same,
the blade is square.
Fig. 36
COMBINATION
SQUARE
If the distances are different:
[] Place spreader/riving knife in "down" position.
[] Loosen adjusting screws in the front and back of the
saw.
NOTE: The adjusting screws are located above the
height/bevel adjusting handwheel and under the saw
table in the front of the saw.
[] If the back of the blade was too far from the combination square, place a block of wood on the left side of
the blade and push it into the blade until the blade is
square. Retighten the screws.
F(g. 37
If the back of the blade was too close to the combination square, place a block of wood on the right side of
the blade and push it into the blade until the blade is
square.
_, ,r_
WARNING:
-_-- ..........
1
[] Retighten the screws.
_ll
_..
To reduce the risk of injury from
kickback, align the rip fence to the blade following
any blade adjustments. Always make sure the rip
fence is parallel to the blade before beginning any
operation.
BLADETOOCLOSETO MITER GAUGEGROOVE
Fig. 38
29
MAKING
CUTS
CROSSCUT
This table saw can perform a variety of cuts that are not all
mentioned in this manual. DO NOT attempt to make any
cuts not covered here unless you are thoroughly familiar
with the proper procedures and necessary accessories.
Your local library has many books on table saw usage and
specialized woodworking procedures for your reference.
PLACERIGHT HAND ON
MITER GAUGE HERE
The blade provided with the saw is a high-quality combination blade suitable for ripping and cross cut operations.
Carefully check all setups and rotate the blade one full
revolution to assure proper clearance before connecting saw to power source. Stand slightly to the side of the
blade path to reduce the chance of injury should kickback
Occur.
A
WARNING:
Do not use blades rated less than the
speed of this tool. Failure to heed this warning could
result in personal injury.
Use the miter gauge when making cross,
and compound miter cuts. To secure the
miter gauge in place by twisting the lock
Always tighten the lock knob securely in
miter, bevel,
angle, lock the
knob clockwise.
place before use.
Fig. 39
SWITCH
ON
NOTE: it is recommended that you place the piece to be
saved on the left side of the blade and that you make a
test cut on scrap wood first.
TO MAKE
A CROSS
\
CUT
SWITCH
OFF
See Figures 39 - 40.
A
A
WARNING:
Make sure the blade guard assembly
is installed and working properly to avoid serious
possible injury.
WARNING:
Using the rip fence as a cutoff gauge
when cross cutting will result in kickback which can
cause serious personal injury.
SWITCHKEY
[] Remove the rip fence.
[] Set the blade to the correct depth for the workpiece.
[] Set the miter gauge to 0° and tighten the lock knob.
[] Make sure the wood is clear of the blade before turning
on the saw.
SWITCHIN LOCKEDPOSITION
[] To turn the saw on, lift the switch button.
Fig. 4O
[] To turn saw off, press the switch button down.
NOTE: To prevent unauthorized use, remove the switch
key as shown in figure 40.
NOTE: The hand closest to the blade should be placed
on the miter gauge lock knob and the hand farthest
from the blade should be placed on the workpiece.
[] Let the blade build up to full speed before moving the
workpiece into the blade.
[] Hold the workpiece firmly with both hands on the miter
gauge and feed the workpiece into the blade.
[]
3O
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
MAKING
MAKING
A RIP CUT
CUT
See Figure 42.
See Figure 41.
A
J_,
A MITER
WARNING:
Make sure the blade guard assembly
is installed and working properly to avoid possible
serious injury.
WARNING:
Make sure the blade guard assembly
is installed and working properly to avoid serious
possible injury.
[] Set the blade to the correct depth for the workpiece.
[] Remove the rip fence.
[] Position the rip fence the desired distance from the
blade for the cut and securely lock the handle.
[] Set the blade to the correct depth for the workpiece.
[] Set the miter gauge to the desired angle and tighten
the lock knob.
[] Make sure the wood is clear of the blade before turning
on the saw.
[]
[] Make sure the wood is clear of the blade before turning
on the saw.
When ripping a long workpiece, place a support the
same height as the table surface behind the saw for
the cut work.
[] Turn the saw on.
[]
[] Turn the saw on.
[] Position the workpiece flat on the table with the edge
flush against the rip fence. Let the blade build up to full
speed before feeding the workpiece into the blade.
Let the blade build up to full speed before moving the
workpiece into the blade.
[] Hold the workpiece firmly with both hands on the miter
gauge and feed the workpiece into the blade.
NOTE: The hand closest to the blade should be placed
on the miter gauge lock knob and the hand farthest
from the blade should be placed on the workpiece.
[] Once the blade has made contact with the workpiece,
use the hand closest to the rip fence to guide it. Make
sure the edge of the workpiece remains in solid contact
with both the rip fence and the surface of the table. If
ripping a narrow piece, use a push stick and/or push
blocks to move the piece through the cut and past the
blade.
[] When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
MITER CUT
[] When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
MITER GAUGE
ANGLED
BLADE
STRAIGHT
RiP CUT
BLADE
RiP
FENCE
SCALE
Fig. 41
Fig. 42
31
MAKINGA BEVELCROSSCUT
BEVELCROSSCUT
See Figures 43 - 44.
WARNING:
MITER GAUGE
STRAIGHT
Make sure the blade guard assembly
BLADEANGLED
is installed and working properly to avoid possible
serious injury.
[] Remove the rip fence.
[] Unlock the bevel locking lever.
[] Adjust the bevel angle to the desired setting.
[] Lock the bevel locking lever.
[] Set the blade to the correct depth for the workpiece.
[] Set the miter gauge to 0° and tighten the lock knob.
[] Make sure the wood is clear of the blade before turning
on the saw.
[] Turn the saw on.
Fig. 44
[] Let the blade build up to full speed before moving the
workpiece into the blade.
MAKING
[] Hold the workpiece firmly with both hands on the miter
gauge and feed the workpiece into the blade.
A BEVEL
RiP CUT
See Figure 45.
A
NOTE: The hand closest to the blade should be placed
on the miter gauge lock knob and the hand farthest
from the blade should be placed on the workpiece.
[] When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
A
VIEWEDFROMTHE FRONT,BELOWTHE TABLESAW
WARNING:
Make sure the blade guard assembly
is installed and working properly to avoid serious
personal injury.
WARNING: The rip fence must be on the right side
of the blade to avoid trapping the wood and causing
kickback. Placement of the rip fence to the left of the
blade will result in kickback and the risk of serious
personal injury.
[] Remove the miter gauge.
[] Unlock the bevel locking lever.
[] Adjust the bevel angle to the desired setting.
BEVEL
LOCKING
LEVER
[] Lock the bevel locking lever.
[] Set the blade to the correct depth for the workpiece.
[] Position the rip fence the desired distance from the
blade for the cut and securely lock the handle.
TO LOOSEN
[] Make sure the wood is clear of the blade before turning
on the saw.
HEIGHT/BEVEL
ADJUSTING
HANDWHEEL
[] When ripping a long workpiece, place a support the
same height as the table surface behind the saw for
the cut work.
[] Turn the saw on.
TO
TIGHTEN
Fig. 43
32
[] Positiontheworkpieceflatonthetablewiththeedge
flushagainsttheripfence.Letthe bladebuildupto
fullspeedbeforefeedingtheworkpieceintotheblade.
[] Oncethe bladehasmadecontactwiththeworkpiece,
usethe handclosestto theripfenceto guideit.
Makesuretheedgeoftheworkpieceremainsinsolid
contactwithboththe ripfenceandthesurfaceofthe
table.If rippinga narrowpiece,usea pushstickand/
or pushblocksto movethe piecethroughthecutand
pasttheblade.
[] Whenthecut ismade,turnthesawoff.Waitforthe
bladeto cometo a completestopbeforeremoving
the workpiece.
[]
Lock the bevel locking lever.
[]
Set the blade to the correct depth for the workpiece.
[]
Set the miter gauge to the desired angle and tighten
the lock knob.
[]
Make sure the wood is clear of the blade before
turning on the saw.
[]
Turn the saw on.
[]
Let the blade build up to full speed before moving the
workpiece into the blade.
[]
Hold the workpiece firmly with both hands on the
miter gauge and feed the workpiece into the blade.
NOTE: The hand closest to the blade should be
BEVELRiP CUT
placed on the miter gauge lock knob and the hand
farthest from the blade should be placed on the
workpiece.
RiP FENCE
BLADE
ANGLED
[]
SCALE
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing
the workpiece.
COMPOUND(BEVEL)MITER CUT
PLACELEFTHANDON MITER
GAUGEHERE
Fig. 45
MAKING A COMPOUND
See Figure 46,
A
(BEVEL)
MITER
CUT
WARNING:
Make sure the blade guard assembly
is installed and working properly to avoid possible
serious injury.
[]
Remove the rip fence.
[]
Unlockthe
[]
Adjust the bevel angle to the desired setting.
bevel locking lever.
Fig. 46
33
MAKING A
LARGE
PANEL CUT
MAKING
A NON-THROUGH
CUT
See Figure 47.
See Figure 48,
Make sure the saw is properly secured to a work surface
to avoid tipping from the weight of a large panel.
Non-through cuts (made with a standard 10 in. blade) can
be made with the grain (ripping) or across the grain (cross
cut). The use of a non-through cut is essential to cutting
grooves, rabbets, and dadoes. This is the only type cut
that is made without the blade guard assembly installed.
Make sure the blade guard assembly is reinstalled upon
completion of this type of cut. Read the appropriate section which describes the type of cut in addition to this
section on non-through or dado cuts. For example, if your
non-through cut is a straight cross cut, read and understand the section on straight cross cuts before proceeding.
A
A
[]
WARNING:
Make sure the blade guard assembly
is installed and working properly to avoid possible
serious injury.
WARNING:
Never make freehand cuts (cuts without
the miter gauge or rip fence). Unguided workpieces
can result in serious injury.
Place a support the same height as the top of the saw
table behind the saw for the cut work. Add supports to
the sides as needed.
A
[] Depending on the shape of the panel, use the rip fence
or miter gauge. If the panel is too large to use either the
rip fence or the miter gauge, it is too large for this saw.
[] Make sure the wood does not touch the blade before
you turn on the saw.
A
[] Turn the saw on.
[] Position the workpiece flat on the table with the edge
flush against the rip fence. Let the blade build up to full
speed before feeding the workpiece into the blade.
WARNING:
When making a non-through cut, the
blade is covered by the workpiece during most of
the cut. Be alert to the exposed blade at the start
and finish of every cut to reduce the risk of personal
injury.
WARNING:
Never feed wood with your hands when
making any non-through cut such as rabbets or
dadoes. To avoid personal injury, always use push
blocks, push sticks, and featherboards.
[] Use a push stick to move the piece through the cut and
past the blade.
[] Unplug the saw.
[]
[] Place spreader/riving
[] Remove the blade guard and anti-kickback
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing
the workpiece.
pawls.
knife in "down" position.
[] Unlock the bevel locking lever.
[] Adjust the bevel angle to 0°.
[] Lock the bevel locking lever.
[] Set the blade to the correct depth for the workpiece.
[] Depending on the shape and size of the wood, use
either the rip fence or miter gauge.
[] Plug the saw into the power source and turn the saw
LARGEPANELCUT
RiP FENCE
on.
[] Let the blade build up to full speed before moving the
workpiece into the blade.
[] Always use push blocks, push sticks, and/or featherboards when making non-through cuts to reduce the
risk of serious injury.
[] When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
Once all non-through cuts are completed:
[] Unplug your saw.
[] Reinstall the spreader/riving knife in the "up" position
then install the blade guard and anti-kickback pawls.
HEIGHT/BEVEL
ADJUSTING
HANDWHEEL
Fig. 47
34
NON-THROUGH CUT
[]
BLADEGUARD
REMOVED
[] Place release lever in locked position.
[]
y
PUSH
STICK
i
Fig. 48
An optional dado throat plate is required for this procedure (see the Accessories section of this manual). All
blades and dado sets must not be rated less than the
speed of this tool. This saw is designed for 5/8 in. dado
cuts. With the purchase of an optional dado throat plate,
it can be used with a 6 in. stack dado (up to width of 3/4
in.). Do not use an adjustable dado or molding cutters on
this saw.
[]
[] Depending on the shape and size of the wood, use
either the rip fence or miter gauge.
[] Turn the saw on.
NOTE: Make sure the wood does not touch the blade
before you turn on the saw. Let the blade build up to
full speed before feeding the workpiece into the blade.
[]
Position the workpiece flat on the table with the edge
flush against the rip fence or miter gauge and hold
firmly against the saw table.
[]
Use a push block or push stick to move the wood
through the cut past the blade. Never push a small
piece of wood into the blade with your hand, always
use a push stick. The use of push blocks, push sticks,
and featherboards are necessary when making nonthrough cuts.
Once aII dado cuts are completed:
[] Unplug your saw.
[] Reinstall the spreader/riving knife in the "up" position then
install the blade guard and anti-kickback pawls.
DADOCUT
WARNING: Always use push blocks, push sticks,
and/or featherboards when making dado cuts to
avoid the risk of serious injury.
Unplug the saw.
[] Remove the blade guard, anti-kickback
plate, and spreader/riving knife.
[]
Install the dado throat plate and rotate the blade by
hand to make sure it turns freely then lower the blade.
[] When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
MAKING A DADO CUT
See Figure 49.
A
Make sure the blade nut is fully engaged and the arbor
extends past a securely tightened blade nut.
pawls, throat
Remove the blade nut, blade washer, saw blade, and
inner blade washer.
NOTE: Always store the blade washer and throat plate
in a secure location.
[] Install the special blade washer included with the dado
throat plate (purchased separately).
[]
Mount the dado blade, according to manufacturer
instructions, using the blade and chippers appropriate
for the desired width of cut.
[]
Reinstall the blade nut.
NOTE: The blade washer may be used provided the
arbor shaft extends slightly beyond the arbor nut.
Fig. 49
35
_I_ WARNING:Beforeperforminganyadjustment,
BLADE
WRENCH
make sure the tool is unplugged from the power
BLADE
WRENCH
supply and the switch is in the OFF position. Failure
to heed this warning could result in serious personal
injury.
The table saw has been adjusted at the factory for making very accurate cuts. However, some of the components
might have been jarred out of alignment during shipping.
Also, over a period of time, readjustment will probably
become necessary due to wear.
To avoid unnecessary set-ups and adjustments, a good
practice is to check your setups carefully with a framing square and make practice cuts in scrap wood before
making finish cuts in good workpieces. Do not start any
adjustments until you have checked with a square and
made test cuts to be sure adjustments are needed.
TO REPLACE
Fig. 50
ARBOR
SHAFT
BLADE
THE BLADE
BLADE
_WASHER
See Figures 50 - 52.
m
[] Unplug the saw.
[] Remove the blade guard and anti-kickback
pawls.
BLADE
NUT
.J
[] Lower the saw blade and remove the throat plate.
[] Make sure the bevel locking lever is locked.
[] Raise the saw blade to full height.
[] Insert the open end of the blade wrench onto the flats
on the arbor shaft.
[] Insert the closed end of the blade wrench over the
blade nut. Holding both wrenches firmly, pull the
outside wrench (right side) forward while pushing the
inside (left side) to the back of the saw. Remove the
nut and blade washer.
Fig. 51
[] Unlock the release lever and remove the blade.
To install a standard b(ade:
[] Place the new blade on the arbor shaft (the teeth
must point down toward the front of the saw to work
properly).
[] Place the blade washer and the blade nut over the
arbor shaft. Be sure the dome side of the blade washer
faces the blade and that all items are snug against the
arbor housing. Make sure the blade nut is securely
tightened. Do not overtighten.
[] Lock the release lever.
THROAT
PLATE
SPREADER/
RIVING KNIFE
BLADE
[] Rotate the blade by hand to make sure it turns freely.
[] Lower the saw blade and reinstall the throat plate.
S
NOTE: To replace the blade with an accessory blade, follow the instructions provided with the accessory.
Fig. 52
36
TO ADJUST
THE MITER
GAUGE
BLADE
See Figure 53.
COMBiNATiON
SQUARE
You can set the miter gauge at 0° and plus or minus
45 ° with the miter gauge stop pin and adjustable stop
screws.
NOTE: The miter gauge provides close accuracy in
angled cuts. For very close tolerances, test cuts are
recommended.
[]
Loosen knob and pull out on stop pin to rotate miter
gauge base past stop screws.
[]
Loosen the lock nut of the 0° stop screw at the stop
pin with a 8 mm wrench.
[]
Place a 90 ° square against the miter gauge rod and
the miter gauge base.
[]
If the rod is not square, loosen the knob, adjust the
rod, and tighten the knob.
O°ADJUSTMENT
SCREW
[] Adjust the 0 ° stop screw until it rests against the
stop pin.
BEVEL
LOCKING
LEVER
[] Adjust the plus and minus 45 ° stop screws using a
45 ° triangle and the steps above.
MITER
GAUGEBASE
HANDLE
BEVEL
INDICATOR
Fig. 54
if the blade is not an exact 45°:
[] Loosen the adjustment screw and the bevel locking
lever.
[] Place a combination
square beside the blade on the left.
[] Turn the handle until the bottom of the blade has moved
completely to the left side of the slot. Lock the angle by
pushing the bevel locking lever.
MITER
GAUGEROD
[] If the blade is not an exact 45 °, loosen the 45 °
adjustment screw and the bevel locking lever.
45° ADJUSTABLE
STOPSCREW
TO SET THE BLADE
[] Adjust the bevel indicator to 45 °.
[] Make a test cut.
LOCK 0° ADJUSTABLE
NUT
STOPSCREW
Fig. 53
AT 0 ° AND 45 °
BLADE
See Figures 54 - 55.
COMBINATION
SQUARE
The angle settings of the saw have been set at the
factory and, unless damaged in shipping, should not require setting during assembly. After extensive use, they
may need to be checked.
[] Unplug the saw.
[] Raise the blade.
45° ADJUSTMENT
SCREW
if the blade is not perfectly vertical (0°):
[] Loosen the adjustment screw and the bevel locking
lever.
[] Place a combination square beside the blade on the
left. Lock the angle by pushing the bevel locking
lever down and retighten the adjustment screw.
[] Turn the handle until the bevel indicator points to
zero. If the handle is turned as far as possible and
doesn't indicate zero properly, you may need to
adjust the bevel indicator.
BEVEL
LOCKING
LEVER
NOTE: It will be necessary to remove the handle to
adjust the bevel indicator.
37
HANDLE
BEVEL
INDICATOR
Fig. 55
TO CHECK
THE ALIGNMENT
OF THE RIP
RiP FENCE
BLADE
FENCE TO THE BLADE
See Figure 56.
[] Unplug the saw.
[] Raise the locking lever to permit the rip fence to be
moved.
[] Place a framing square beside the blade and move
the rip fence up to the square. Take the dimension on
the rip scale.
[] Move the fence back and turn the framing square
180 ° to check the other side.
[] If the two dimensions are not the same, loosen the
two bolts on the fence and align it.
BOLTS
[] Retighten the two bolts.
[] Make two or three test cuts on scrap wood. If the
cuts are not true, repeat the process.
LOCKING
LEVER
Fig. 5
A
A
A
WARNING:
When servicing, use only identical
replacement parts. Use of any other parts may
create a hazard or cause product damage.
[] Check the blade guard assembly.
WARNING:
Always wear eye protection with side
shields marked to comply with ANSI Z87.1 during
product operation. If operation is dusty, also wear a
dust mask.
WARNING:
Before performing any maintenance,
make sure the tool is unplugged from the power
supply and the switch is in the off ( O ) position.
Failure to heed this warning could result in serious
personal injury.
GENERAL
MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
A
[] Periodically check all clamps, nuts, bolts, and screws for
tightness and condition. Make sure the throat plate is in
good condition and in position.
[] To maintain the table surfaces, fence, and rails,
periodically apply paste wax to them and buff to provide
smooth functioning.
[] Protect the blade by cleaning out sawdust from
underneath the table and in the blade teeth. Use a resin
solvent on the blade teeth.
[] Clean plastic parts only with a soft damp cloth. DO NOT
use any aerosol or petroleum solvents.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrication is required.
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc., come in contact with plastic parts.
Chemicals can damage, weaken, or destroy plastic
which may result in serious personal injury.
38
Thefollowingrecommended
accessories
arecurrentlyavailableatretailstores:
089037008711 DadoThroatPlatewithSpecialWasher
_I_, WARNING:Currentattachments
andaccessories
available
for usewiththistool arelistedabove.Donotuse
anyattachments
or accessories
not recommended
bythe manufacturer
ofthistool.Theuseof attachments
or
accessories
not recommended
canresultin seriouspersonalinjury.
CAUSE
PROBLEM
Excess vibration.
SOLUTION
Blade is out of balance.
Replace blade.
Blade is damaged.
Replace blade.
Saw is not mounted securely.
Tighten all hardware.
Work surface is uneven.
}
Reposition on flat surface.
Adjust legs of optional stand.
Blade is warped.
Check saw blade installation. Replace blade if
necessary.
Rip fence not mounted correctly.
Remount the rip fence.
Rails are dirty or sticky.
Clean and wax rails.
Clamp screw is out of adjustment.
Adjust clamp screw counterclockwise.
Rip fence does not lock at
rear.
Clamp screw is out of adjustment.
Adjust clamp screw clockwise.
Cutting binds or burns work.
Blade is dull.
Replace or sharpen blade.
Blade is heeling.
See page 29 on "Heeling the Blade".
Work is fed too fast.
Slow the feed rate.
Rip fence is misaligned.
Align the rip fence.
Wood is warped.
Replace the wood. Always cut with convex
side to table surface.
Spreader is out of alignment.
See "To check and align the spreader/riving knife
and saw blade" in the Assembly section.
Blade not properly sharpened or set.
Resharpen or set blade.
Rip fence does not move
smoothly.
Wood edges away from rip
fence when ripping.
39
PROBLEM
Saw does not make accurate
90 ° or 45 ° cuts.
CAUSE
SOLUTION
Positive stops inside cabinet need
adjusting (Bevel Cuts).
Adjust positive stops.
Miter gauge is misaligned (Miter
Adjust the miter gauge.
Cuts).
Height/bevel adjusting handwheel is hard to turn.
Gears or screw post inside
Saw does not start.
Motor cord or wall cord is not
Clean the gears or screw post.
cabinet are clogged with saw
dust.
Plug in motor cord or wall cord.
plugged in.
Circuit fuse is blown.
Replace circuit fuse.
Circuit breaker is tripped.
Reset circuit breaker.
Cord or switch is damaged.
Have the cord or switch replaced at your
nearest authorized service center.
Blade is dull or dirty.
Clean, sharpen, or replace blade.
Blade is wrong type for cut being
made.
Replace with correct type.
Blade is mounted backwards.
Remount blade.
Blade does not lower when
turning height/bevel adjusting
handwheel.
Locking lever is not at full left
Move locking lever to left.
Motor labors in rip cut.
Blade not proper for rip cut.
Blade makes poor cuts.
position.
4O
Change blade; rip blade typically has fewer
teeth.
i
,-
CRAFTSMAN
10 in. TABLE
SAW
- MODEL
NUMBER
315.284620
-_
47
45
45
43
55
See Figure
D
42
4O
32
28
34
31
l" 27
26
33
3O
35
FIGURE A
36
37
CRAFTSMAN
f
10 in. TABLE SAW - MODEL
NUMBER
he model number will be found on a label attached to the cabinet. Always mention the model number in all correspondence
10 in. PORTABLE TABLE SAW or when ordering parts.
PARTS LiST FOR FIGURE
KEY
NO,
315.284620
PART
NUMBER
1
2
3
4
5
6
7
8
9
089037008032
089037008031
089110118004
089110118003
089037008033
089037008027
089037008025
089037008026
089037008028
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
089037008023
089037008024
089037008042
089037008041
089037008040
089037008034
089037008037
089037008036
089037008035
089037008038
089037008039
089037008004
089037008005
089037008006
089037008007
089037008702
089037008046
089037008045
089037008043
089037008018
089037008044
089037008055
089110118001
089037008056
DESCRIPTION
QTY
Screw (M6 x 65 mm) ........................................
Handle ..............................................................
End Cap ...........................................................
Height/Bevel Adjusting Handwheel .................
Nut (M6) ...........................................................
Pin (D3.6 x 22 mm) ..........................................
Elevation Rod ...................................................
E-Ring ..............................................................
Compression Spring
(Dll.8 x D9.8 x D1.0 x 65 mm) ........................
Bevel Gear .......................................................
Screw (M4 x 20 mm) ........................................
Screw (M4 x 18 mm) ........................................
Bevel Locking Lever ........................................
Pad ...................................................................
Screw (M8 x 51 mm) ........................................
Washer (D18 x D8.5 x 2t) .................................
Spring (D18 x 8.4 x lt) .....................................
Bevel Bushing (D20 x D8.5 x 116.9t) ...............
Nut (M8) ...........................................................
Nut (M8) ...........................................................
Slider- Undercarriage ......................................
Screw (M6 x 12 mm) .......................................
Washer (M6) .....................................................
Bevel Trunnion - Front .....................................
Motor Assembly ...............................................
Screw (M4 x 7 mm) ..........................................
Indicator ...........................................................
Indicator Holder ...............................................
Washer (M4) .....................................................
Screw (M4 x 10 mm) ........................................
Inner Blade Washer ..........................................
Blade (10 in. x 5/8 in. x 36t) .............................
Outer Blade Washer .........................................
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
4
4
1
1
1
1
1
2
2
1
1
1
KEY
NO.
regarding your
1
A
PART
NUMBER
DESCRIPTION
QTY
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
089037008057
089037008178
089037008058
089110118706
089037008059
089037008003
089037008067
089110118005
089037008068
089110118704
089037008065
089037008063
089037008064
089037008062
089037008908
089037008705
089110118702
089110118703
52
53
54
55
56
57
58
59
60
61
089037008703
089037008060
089110118701
089110118903
089037008905
089110118908
089110118909
089110113913
089110118905
089110118904
Nut (5/8 in. x 8 mm) .........................................
Dust Chute Cover ............................................
Dust Chute .......................................................
Dust Bag w/Elbow Assembly ..........................
Screw (10-32 x 8 mm) .....................................
Bevel Trunnion - Rear ......................................
Screw (M3 x 10 mm) ........................................
Push Stick ........................................................
Nut (M3) ...........................................................
Miter Gauge Assembly ....................................
Screw (M4 x 10 mm) ........................................
Extension Rod (O16 x It x 535 mm) ................
Screw (M6 x 12 mm) ........................................
Outfeed Support ..............................................
Warning Label ..................................................
Anti-Kickback Pawls ........................................
Throat Plate Assembly .....................................
Blade Guard Assembly
(Inc. Key Nos. 56-61) .......................................
Spreader/Riving Knife Assembly .....................
Screw (M6 x 16 mm) ........................................
Saw Table Assembly ........................................
Rip Scale ..........................................................
Inner Guard Installation Label ..........................
Side Barrier Warning - Right ............................
Side Barrier Warning - Left ..............................
No Hands Warning Label .................................
Upper Barrier Warning Label ...........................
Outer Guard Installation Label .........................
089110118708
987000910
Not Shown:
Optional Dado Throat Plate ............................. 1
Operator's Manual .......................................... 1
1
1
1
1
2
1
2
1
2
1
2
2
2
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
,.,.
CRAFTSMAN
10 in. TABLE
SAW
- MODEL
NUMBER
315.284620
-_
28
26
See Figure
C
7
See Figure
FIGURE
B
E
CRAFTSMAN 10 in. TABLE SAW - MODEL NUMBER
I
he model number will be found on a label attached to the cabinet. Always mention the model number in all correspondence
10 in. PORTABLE TABLE SAW or when ordering parts.
PARTS LIST FOR FIGURE
KEY
NO.
315.284620
PART
NUMBER
DESCRIPTION
1
089110118707
Quick Stand (Leg Stand) ..................................
1
2
089037008901
Warning Label ..................................................
3
089110118901
4
1
B
PART
NUMBER
DESCRIPTION
16
089037008017
Screw (M4 x 5 mm) ..........................................
2
1
17
089037008053
Screw (M4 x 18 mm) ........................................
7
Main Label .......................................................
1
18
089110101701
Switch Assembly .............................................
1
089037008010
Nut (M6) ...........................................................
4
19
089037008050
Switch Box .......................................................
1
5
089110118015
Cabinet ............................................................
1
20
089037008054
Pad ..................................................................
1
6
089110118002
Locking Knob ...................................................
4
21
089037008012
Knob Ring ........................................................
1
7
089110118705
Rip Fence Assembly ........................................
1
22
089037008047
Blade Wrench ..................................................
2
8
089037008022
Screw (M4 x 15 mm) ........................................
2
23
089037008048
Knob ................................................................
1
9
089037008021
Gear Rack ........................................................
1
24
089037008051
Strain Relief ......................................................
1
10
089037008020
Screw (10 x 8 mm) ...........................................
2
25
089037008052
Power Cord ......................................................
1
11
089037008015
Screw (M5 x 16 mm) ........................................
2
26
089037007902
Warning Label ..................................................
1
12
089037008016
Washer (M5) .....................................................
2
27
089037008011
Bolt (M8 x 40 mm) ...........................................
1
13
089037008014
Reinforcement
1
28
089037008013
Screw (M6 x 25 mm) ........................................
4
14
089037008019
Cam (4 mm) .....................................................
2
29
089110118902
Data Label ........................................................
1
15
089037008018
Washer (M4) .....................................................
4
30
0121010232
Switch Key .......................................................
1
QTY
Plate ........................................
KEY
NO.
regarding your
QTY
,.,.
CRAFTSMAN
10 in. TABLE
SAW
- MODEL
NUMBER
315.284620
-_
7
8
10
36
24
16
18
25
26
29
42
25
35
34
!43
33
FIGURE C
I',
32
_k47
_
,.,,
CRAFTSMAN 10
I
in. TABLE
SAW
- MODEL
315.284620
The
10 in.
model
PORTABLE
number TABLE
will be found
SAW or
onwhen
a label
ordering
attachedparts.
to the cabinet. Always mention the model number in all correspondence
PARTS LIST FOR FIGURE
KEY
NO.
NUMBER
PART
NUMBER
DESCRIPTION
1
089110118006
Saw Table ........................................................
2
089037008073
Outfeed Bracket ...............................................
3
089037008179
Screw (M5 x 12 mm) ........................................
4
089037008078
Pin (D5 x 16 mm ..............................................
5
089037008076
6
7
-_
J
regarding your
1
C
KEY
NO.
PART
NUMBER
DESCRiPTiON
1
26
089037008156
Rip Fence Slider - Left .....................................
1
2
27
089037008155
Rip Fence Slider - Right ...................................
1
4
28
089110118010
Rip Fence Block ...............................................
1
2
29
089037008162
Rod (D5,2 x 580 mm) .......................................
1
Table Locking Lever .........................................
2
30
089037008164
Screw (M6 x 16 mm) ........................................
2
089037008077
Bolt ..................................................................
2
31
089037008168
Indicator ...........................................................
1
089037008075
Extension Rod Bracket ....................................
2
32
089037008161
Ring Pad ..........................................................
2
8
089037008074
Screw (M5 x 12 mm) ........................................
4
33
089037008160
Washer (D25 x D16 x 1.5t ) .............................. 2
9
089037008079
Nut (M5) ...........................................................
2
34
089037008159
Bushing ............................................................
1
10
089037008085
Screw (M4 x 25 mm) ........................................
1
35
089037008158
11
089037008084
Indicator ...........................................................
1
36
089037008076
Locking Lever ..................................................
Miter Lock Knob ..............................................
1
1
12
089037008083
End Plug ..........................................................
1
37
089037008153
Washer (D16 in. x D1/4 x 1,5t) ......................... 1
13
089110118007
Extention Rod (D16 x 1.2t x 641,2 mm) ........... 2
38
089037008149
Washer (D16 x D6.5 x 1.8t) .............................. 1
14
089037008065
Screw (M4 x 10 mm) ........................................
1
39
089037009043
Screw (M4 x 10 mm) ........................................
1
15
089110118008
Sliding Table Extension ....................................
1
40
089037009042
Indicator ...........................................................
1
16
089037008081
Screw (M5 x 25 mm) ........................................
4
41
089110118009
Miter Gauge .....................................................
1
17
089037008086
Miter Gauge Storage Holder ............................ 1
42
089037009039
Miter Gauge Rod .............................................
1
18
089037008087
Screw (M4 x 12 mm) ........................................
3
43
089037009038
Roll Pin (D1/4 x 18 mm) ...................................
1
Nut (M6) ...........................................................
QTY
QTY
19
089037008033
1
44
089037009036
Screw (6-32 x 5/8 in.).......................................
3
20
089037008165
Washer (D1/4 in. x D16 x 1,5t) ......................... 4
45
089037009041
Pin (D6,15 x 23 mm) ........................................
1
21
089037008166
Rear Clamp ......................................................
1
46
089037009040
Indicator Holder ...............................................
1
22
089037008167
Spring (D10.4 x D8 x D1,2 x 32L) .................... 1
47
089037008065
Screw (M4 x 10 mm) ........................................
2
End Cap ...........................................................
1
48
089037009037
Hex Nut (6-32) ..................................................
3
1
49
089110118907
Logo Label .......................................................
1
3
50
089110118906
Scale (Miter Gauge) .........................................
1
23
089037008169
24
089037008163
25
089037008157
Rip Fence .........................................................
Screw (M4 x 8 mm) ..........................................
,.,.
CRAFTSMAN
10 in. TABLE
SAW
- MODEL
NUMBER
315.284620
-_
See Note On Page 48
8
5
27
28
\
\
\
6
1
11
6
\'_
3
2O
FIGURE D
21
,-,
CRAFTSMAN
I
10 in. TABLE
SAW
- MODEL
315.284620
Thein.
model
number TABLE
will be found
onwhen
a label
attachedparts.
to the cabinet. Always mention the model number in all correspondence
10
PORTABLE
SAW or
ordering
PARTS LiST FOR FIGURE
KEY
NO.
NUMBER
PART
NUMBER
DESCRiPTiON
1
089037008096
Screw (M6 x 16 mm) ........................................
2
2
089037008094
T-Nut (Undercarriage) .......................................
3
089037008095
4
J
regarding your
1
D
PART
NUMBER
DESCRIPTION
18
089037008106
Bushing ............................................................
1
19
089037008105
Washer (D5 x D12 x 1.5t) ................................. 2
T-Nut (Wear Plate) ............................................
2
20
089037008091
Elevation Rod ...................................................
1
089037008099
Screw (M5 x 14 mm) ........................................
4
21
089037008024
Screw (M4 x 20 mm ) .......................................
1
5
089037008097
Pivot Plate-Rear ...............................................
1
22
089037008023
Bevel Gear .......................................................
1
6
089037008079
Nut (M5) ...........................................................
4
23
089037008092
Washer (D8 x D22 x 2t) ....................................
1
7
089037008088
1
24
089037008093
Washer (D6.2 x D12 x 2t) .................................
1
8
089037008708
Motor Assembly ...............................................
1
25
089037008033
Nut (M6) ...........................................................
1
9
089037008090
Ring (S17) ........................................................
1
26
089037008173
Key (4 x 4 x 10) ................................................
1
10
089037008089
Bushing ............................................................
1
27
089037008115
Brush ...............................................................
2
11
089037008098
Pivot Plate-Front ..............................................
1
28
089037008116
Brush Cap ........................................................
2
12
089037008104
Screw (M5 x 12 mm) ........................................
2
29
089037008170
Arbor ................................................................
1
13
089037008100
Bracket - Undercarriage ..................................
1
30
089037008172
Ball Bearing (6002 LLU CM) ............................ 1
14
089037008101
Screw (M5 x 12 mm) ........................................
1
31
089037008107
C-Ring (S-15) ...................................................
1
15
089037008102
Screw (M5 x 12 mm) ........................................
1
32
089037008171
Bearing Cover Plate .........................................
1
16
089037008103
Bracket ............................................................
1
33
089037008174
Reduction Gear ................................................
1
17
089037008107
C-Ring ..............................................................
1
QTY
Undercarriage ..................................................
KEY
NO.
-_
QTY
NOTE: The assembly shown represents an important part of the double insulated system. To avoid the possibility of alteration or damage to the system,
service should be performed by your nearest Sears Repair Center. Contact your nearest Sears retail store for service center information.
1
CRAFTSMAN
all correspondence
10 in. TABLE SAW - MODEL
NUMBER
315.284620
regarding your TABLE SAW or when ordering repair parts.
4
\
4
7
7
9
6
__,,,.7
4
7
7
6
1211
3
10
10
0
10
FIGURE E
PARTS LIST FOR FIGURE E
KEY
PART
NO.
1
NUMBER
089110118011
DESCRIPTION
Leg "A". ...................................................................................
1
2
089110118012
Leg "B'. ...................................................................................
3
3
089037008183
4
089037008184
Leg Adaptor ............................................................................
Connector Bracket ..................................................................
4
4
5
089037008185
Screw (M5 x 10 mm) ...............................................................
4
6
089110118013
7
089037008187
Linkage ....................................................................................
Screw (M5 x 15 mm) .............................................................
8
20
8
089037008188
Lock Nut (M5) ........................................................................
20
9
089037008189
10
089037008190
Spacer .....................................................................................
Foot .........................................................................................
4
4
11
089037008191
Red Indicator ...........................................................................
1
12
089037008192
Screw (M4 x 8 ram) .................................................................
1
49
QTY.
_,
CRAFTSMAN
10 in. TABLE SAW - MODEL
NUMBER
315.284620
J
The
all correspondence
model number will
regarding
be found
youronTABLE
a label SAW
attached
or when
to the
ordering
cabinet.repair
Always
parts.
mention the model number in /
4
/
5
6
7
FIGURE
8
F
PARTS LIST FOR FIGURE F
KEY
PART
NO.
NUMBER
DESCRIPTION
QTY.
1
089037008033
Nut (M6) ..................................................................................
1
2
089037008124
3
089037008119
Screw (M6 x 10 mm) ...............................................................
Deck .......................................................................................
2
1
4
089037008000
Spreader/Riving
1
5
089037008120
6
089037008121
Clamp .....................................................................................
Release Lever .........................................................................
1
1
7
089037008123
Spring (D10 x D6.5 x 16L) .......................................................
1
8
089037008125
Washer (D14 x D6.5 x 2t) ........................................................
1
9
089037008122
Screw (M6 x 32 mm) ...............................................................
1
5O
Knife .............................................................
Your Home
For expert troubleshooting
and home solutions advice:
@anag@
www.managemyhome.com
For repair - in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
Call anytime,
®
(1-800-469-4663)
day or night (U.S.A. and Canada)
www.sears.com
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service
1-800-488-1222
(U.S.A.)
1-800-469-4663
To purchase a protection agreement
on a product serviced by Sears:
(U.S.A.)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR
1-800-361-6665
(Canada)
Au Canada pour service
en fran£ais:
1-800-LE-FOYER
®
Trademark
/ TMTrademark
/ SMService
M°
(1-800-533-6937)
www.sears.ca
(1-888-784-6427)
® Registered
(Canada)
www.sears.ca
www.sears.com
1-800-827-6655
Center
Mark of Sears Brands,
® Marca Registrada / TM Marca de Fabrica / SM Marca de Servicio
MC Marque de commerce / MD Marque depos6e de Sears Brands,
LLC
de Sears Brands,
LLC
LLC
© Sears
Brands,
LLC