Hard Disk Drive for Operating instructions

Hard Disk Drive for Operating instructions
Hard Disk Drive
for
(Here iS 40 Picture)
Operating
instructions
Table of Contents:
Introduction
1. Play Standard MIDI File
2. "COPY FILE" function
3. Formatting Hard Disk Partitions
©1998 musitronics GmbH
Introduction:
Generally, KORG IS40/IS50 keyboards with a hard disk offer the same control panel as
normal IS40/IS50 keyboards. Thus, no additional keys or switches are necessary.
The commands for loading (LOAD) and storing (SAVE) data (All Data, Programs,
Arrangements, Styles, Backing Sequences) stay the same.
The new functions only refer to floppy disk functions in DISK mode and to SONG PLAY
mode.
Until now, in GLOBAl/DISK mode, it has only been possible to LOAD DATA from floppy
disk drive. The following message has been displayed on the screen (see fig.1).
Abb.1
Disk
(LOAD)
(Press Yes)
(SAVE)
(UTIL)
Before:
The LCD screen of KORG’s IS40/IS50 consists of two lines. Until now, the upper line has
shown the message Disk
(Press Yes). With the cursor keys you can determinate if you
want load, store or utility functions. In order to execute the command, press ENTER/YES
key.
Expanded System:
With the new disk operating system, press and hold DISK mode key. Now, you are allowed to
select either the floppy disk drive or one of the hard disk partitions (C, D, E, F, G ....) with the
cursor UP/DOWN keys. (Fig.2)
Fig. 2
HD-C
(LOAD)
(Press Yes)
(SAVE)
(UTIL)
Note:
The upper line of the LCD screen displays the message ‘HD-C (Press Yes)’. This refers to
hard disk partition ‘C’, which is always selected after switching on power. Once having
selected a hard disk partition, all LOAD, SAVE and UTILITYr commands like FORMAT and
DELETE are executed as usually.
In each partition you can store 224 data files.
1
One examples for selecting different hard disk partitions:
Selection of hard disk partition ‘T’(display message: ‘HD-T’) via UP/DOWN keys.
(1) Press DISK mode key (upper line of display: ‘HD-C (Press Yes’).
(2) Press and hold DISK mode key.
(3) Press UP key several times (17 x). The upper line displays: ‘HD-T (Press Yes)’.
The above mentioned functions also apply to all other LOAD, SAVE, COPY, FORMAT and
DELETE commands in DISK mode.
For all normal operating steps please refer to your KORG IS40/IS50 Player’s Guide or
Reference Guide as usually.
The following functions offer new options:
1. Play Standard MIDI File
2. ‘COPY FILE’
1. Play Standard MIDI File
First, select ‘SONG PLAY’ mode. Press and hold ‘SONG PLAY’ mode key. Now, you may
select either the floppy disk drive or one of the hard disk partitions (C,D,E,F,G....) via
UP/DOWN keys.
MIDI files with formats 0 or 1 can be selected alphabetically as well as numerically (song
number):
If you are accustomed to assign your songs to fixed memory locations on the bulk memory
(hard disk) it is also possible to do so with the hard disk of your IS40/IS50 HD. Therefore, the
songs have to be stored in the desired order; the memory locations (song numbers) once
chosen are maintained until deleting the files.
It is not possible to assign the numbers directly on the hard disk. They are assigned
continuously in the order of storage.
If a song is deleted from the partition all other memory locations are maintained. The next
song to store is written to the empty location.
Numeric Selection of MIDI files
For a numeric selection of Standard MIDI Files enter the corresponding song number via
ARRANGEMENT. A bank and Bank refers to number 0 and USER Bank to number 9. Please
see fig.3; the figures in brackets are used to enter the numbers.
2
Fig. 3
ARRANGEMENT
Bank
A
B
User
0
0
Number
1
2
9
3
4
5
6
7
8
Example: Selection of song number 105
ARRANGEMENT
Bank
A
B
0
User
0
Number
1
2
9
3
4
5
6
7
8
Alphabetic Selection of MIDI files
In order to select a song alphabetically, press the UP or DOWN key. The message ‘Wait a
moment...’ appears in the upper line of the LCD screen . After a short period, the first song is
displayed. Now, it is possible to select the songs of the corresponding partition alphabetically
via VALUE (iS40) dial or UP/DOWN key.
Starting a Song:
After pressing START/STOP key the song is played back automatically.
Note: It is also possible to select the next song numerically while playing back a MIDI file.
Having finished the first song, the next starts immediately.
3
2. ‘COPY FILE’
In order to store data on the hard disk, use the normal ‘save functions’ of DISK mode. Those
functions, however, do not allow writing original MIDI files to the hard disk. Hence, you are
provided with a new function in DISK mode: the ‘COPY FILE’ function. (See page 6-1,
DISK mode.)
With this function you are able to copy all data (Arrangements, Styles, Backing Sequences,
Programs, and MIDI files) directly from floppy disk or a certain hard disk partition to any
other HD-partition. (See fig. 4.)
Fig. 4
HD-C
(LOAD)
(Press Yes)
(SAVE)
HD-C
(DEL)
(UTIL)
YES
Utility
(E.S)
(CPY) (FMT)
Procedure:
First, select DISK mode.Select via cursor keys (UTIL) and press the ENTER/YES key. Now
selet via cursr keys (CPY) and press ENTER/YES . Press and hold DISK mode key again
and select the ‘source’ drive (drive which contains the data to copy, e.g. DISK for the floppy
disk drive) via cursor UP/DOWN keys. Now, press cursor key and select the ‘destination’
drive (drive which is chosen to write the data to) via VALUE dial or UP/DOWN keys.
‘COPY FILE’ provides you with three alternative functions:
(2.1) Copy a single file:
When you select this function, a single file is copied from source drive to destination drive.
x Select name of file via VALUE dial or UP/DOWN keys.
x Press ENTER/YES to execute command.
(2.2) Copy all MIDI files of a volume: “MIDI files”
When you select this function, only the MIDI files of a floppy disk or a certain hard disk
partition are copied.
x Select “MIDI Files” via VALUE dial or UP/DOWN keys. (Turn the wheel right.)
x Press ENTER/YES to execute command.
4
(2.3) Copy all files: “All files”
When you select this function, the ‘ALL’ Programs, Arrangements, Styles, and Backing
Sequences of a floppy disk or a hard disk partition are copied.
x Select “All files” via VALUE dial or UP/DOWN keys. (Turn the wheel right.)
x Press ENTER/YES to execute command.
Note: With the ‘COPY FILE’ function it is possible to copy data from floppy disk to a certain
hard disk partition, between different hard disk partitions and from hard disk to floppy disk.
Important Note: The IS40 HD-Operating Systen can show lyrics on the display. So use the
copy function that the MIDI files are copy including the lyrics.
3. Formatting floppy disks and partitioning hard disk
Select DISK Mode. Select UTILITY and press YES/ENTER key, than select FMT and
press YES/ENTER again.
Formatting floppy disks
It is always possible to format floppy disks. In order to select floppy disk drive, press cursor
UP/DOWN key while holding DISK mode key until DISK appers in the upper line of the
LED screen.
Execute the command via cursor ENTER/YES key.
In the case that the floppy disk has already been formatted, the question “Continue? YES
NO” is displayed. Now, confirm with ENTER/YES key or cancel the procedure using
EXIT/NO key.
Formatting hard disk partitions
Each of the hard disk partitions can - has to, respectively - be formatted individually (after
having installed the hard disk expansion).
Note: The function to format hard disk partitions is only accessible when you press and hold
‘PROGRAM’ and ‘GLOBAL’ mode keys simultaneously while switching on the IS40/IS50
HD.
Now, select a hard disk partition as described above.
Confirm via cursor key ENTER/YES .
In the case that the hard disk partition has already been formatted or any data have been stored
on it, the question “Continue? YES NO” is displayed. Confirm via ENTER/YES key or
cancel the procedure using EXIT/NO key.
5
Important: Each hard disk system has been tested before delivery. Thus, the hard disk is partly
formatted or contains test data. The procedure of installing a hard disk expansion, however, is
a serious intervention in the disk operation system of the keyboard. In order to guarantee
correct performance, it is necessary to initialize and re-format the device after installation. To
initialize the IS40/IS50 HD, press and hold ‘PROGRAM’ and ‘DISK’ mode keys
simultaneously while switching on the unit.
NOTE: We are not liable for any loss of data caused by faulty hardware or wrong operations
6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising