Owner`s manual | Craftsman 486.24251 Lawn Mower User Manual

Owner's Manual
JCRRFTSMRN°J
LAWN TRACTOR
18.5 HP, 42" Mower
Electric Start
Automatic Transmission
Model No.
917.275820
[_
differently
from
built engines.
Before operates
you start the
his product
haspreviously
a low emission
engine which
engine, read and understand this Owner's Manual,
IMPORTANT:
For answers to your questions
Read and follow all Safety
Rules and Instructions before
about this product, Call:
operating this equipment.
Sears Craftsman Help Line
5 am - 5 pm, Mon- Sat
1-800-659-5917
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A
Visit our Craftsman
website:www.sears.com/craftsman
Warranty ................................................
Safety Rules ..........................................
Product Specifications
...........................
AssemblyPre-Operation
........................
Operation .............................................
Maintenance
.......................................
2
3
6
8
11
18
Maintenance
Schedule ........................
18
Service and Adjustments
.....................
23
Storage ................................................
29
Troubleshooting
...................................
30
Repair Parts .........................................
34
Sears Service ........................
Back Cover
LIMITED WARRANTY
ON CRAFTSMAN
RIDING EQUIPMENT
For two (2) years from the date of purchase,
if this Craftsman
Riding Equipment
is
maintained,
lubricated
and tuned up according
to the instructions
in the owner's manual,
Sears will repair or replace free of charge any parts that are found to be defective in
material or workmanship
according to the guidelines
of coverage listed below. Sears will
also provide free labor for these applicable warranted
parts for the two full years. During
the first 30 days of purchase, there will be no charges to service the product at your
home for issues covered by this warranty. (See exclusions
below).
For your convenience,
IN HOME warranty service will still be available after the first 30 days of purchase, but a trip charge will apply. This charge will be waived if the Craftsman product is
dropped off at an authorized
Sears location. For the nearest authorized
Sears location,
please call 1-800-4-MY-HOME®.
This warranty applies only while this product is within
the United States.
This Warranty does not cover:
• Expendable
items which become worn during normal use, including but not limited to
blades, spark plugs, air cleaners, belts, and oil filters.
• Standard Maintenance
Servicing, oil changes,
or tune-ups
• Tire replacement
or repair caused by punctures from outside objects, such as nails,
thorns, stumps, or glass.
• Repairs necessary
because of operator abuse, including but not limited to, damage
caused by towing objects beyond the capability of the riding equipment,
impacting
objects that bend the frame or crankshaft,
or over-speeding
the engine.
• Repairs necessary
because of operator negligence,
including but not limited to, electrical and mechanical
damage caused by improper storage, failure to use the proper
grade and amount of engine oil, failure to keep the deck clear of flammable
debris,
or failure to maintain the equipment
according to the instructions
contained
in the
owner's manual.
• Engine (fuel system) cleaning or repairs caused by fuel determined
to be contaminated or oxidized (stale). In general, fuel should be used within 30 days of its purchase date.
• Normal deterioration
and wear of the exterior finishes, or product label replacement.
• Riding equipment
used for commercial
or rental purposes.
LIMITED WARRANTY
ON BATTERY
For ninety (90) days from date of purchase, if any battery included with this riding equipment proves defective in material or workmanship
and our testing determines
the battery
will not hold a charge, Sears will replace the battery at no charge.
During the first 30
days of purchase, there will be no charges to replace the battery at your HOME. After
the first 30 days, for your convenience,
IN-HOME warranty service will still be available but a trip charge will apply. This charge will be waived if the Craftsman product is
dropped off at an authorized
Sears location. For the nearest authorized
Sears location,
please call 1-800-4-MY-HOME®.
This battery
warranty
applies
only while
This warranty gives you specific
vary, from state to state.
Sears,
Roebuck
this product
is within the United
States.
legal rights, and you may also have other rights,
and Co.,Dept.817WA,
Hoffman
Estates,
IL 60179
which
IMPORTANT:This cutting machineis capableof amputatinghandsand feet and throwing objects.Failureto observe the followingsafety instructionscould result in serious
injury or death.
_IWARNING: Inorder to preventaccidental startingwhen setting up, transporting, adjustingor making repairs,
always disconnectspark plug wire and
place wire where it cannotcontact spark
plug.
_I_WARNING:
Do not coast down a hill in
neutral, you may lose control of the tractor.
_,WARNING:
Tow only the attachments
that are recommended
by and comply with
specifications
of the manufacturer
of your
tractor. Use common sense when towing.
Operate only at the lowest possible speed
when on a slope. Too heavy of a load,
while on a slope, is dangerous.
Tires can
lose traction with the ground and cause
you to lose control of your tractor.
•
•
•
•
•
_,WARNING:
Engine exhaust, some of
its constituents,
and certain vehicle components contain or emit chemicals
known
to the State of California to cause cancer
•
and birth defects
harm.
•
or other
_,WARNING:
Battery
and related accessories
reproductive
posts, terminals
contain lead and
•
lead compounds,
chemicals
known to the
State of California to cause cancer and
•
birth defects or other reproductive
Wash hands after handling.
I. GENERAL
•
•
•
•
•
•
•
harm.
•
OPERATION
Read, understand,
and follow all
instructions
on the machine and in the
manual before starting.
Do not put hands or feet near rotating
parts or under the machine. Keep clear
of the discharge
opening at all times.
Only allow responsible
adults, who are
familiar with the instructions,
to operate
the machine.
Clear the area of objects such as
rocks, toys, wire, etc., which could be
picked up and thrown by the blades.
Be sure the area is clear of bystanders before operating.
Stop machine if
anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary.
Always look down
and behind before and while backing.
•
•
•
Never direct discharged
material
toward anyone. Avoid discharging
material against a wall or obstruction.
Material may ricochet back toward the
operator. Stop the blades when crossing gravel surfaces.
Do not operate machine without the
entire grass catcher, discharge guard,
or other safety devices in place and
working.
Slowdown
before turning.
Never leave a running machine
unattended.
Always turn off blades,
set parking brake, stop engine, and
remove keys before dismounting.
Disengage
blades when not mowing.
Shut off engine and wait for all parts to
come to a complete stop before cleaning the machine, removing the grass
catcher, or unclogging
the discharge
guard.
Operate machine only in daylight or
good artificial light.
Do not operate the machine while
under the influence of alcohol or drugs.
Watch for traffic when operating near
or crossing roadways.
Use extra care when loading or unloading the machine into a trailer or
truck.
Always wear eye protection when operating machine.
Data indicates that operators, age 60
years and above, are involved in a
large percentage
of riding mower-related injuries. These operators should
evaluate their ability to operate the
riding mower safely enough to protect
themselves
and others from serious
injury.
Follow the manufacturer's
recommendation for wheel weights or counterweights.
Keep machine free of grass, leaves or
other debris build-up which can touch
hot exhaust / engine parts and burn.
Do not allow the mower deck to plow
leaves or other debris which can cause
build-up to occur. Clean any oil or fuel
spillage before operating or storing the
machine. Allow machine to cool before
storage.
II. SLOPE OPERATION
Slopes are a majorfactor relatedto loss of
controland tip-overaccidents,which can
result in severeinjury or death. Operation on all slopes requiresextra caution. If
you cannot back up the slope or if you feel
uneasy on it, do not mow it.
• Mow up and down slopes,not across.
• Watchfor holes, ruts, bumps,rocks,or
other hiddenobjects. Uneventerrain
could overturnthe machine. Tallgrass
can hide obstacles.
• Choosea low groundspeed so that
you will not haveto stop or shift while
on the slope.
• Do not mow on wet grass.Tires may
lose traction.
Always keepthe machine in gear when
going down slopes. Do not shift to
neutral and coast downhill.
•
•
•
•
•
Avoid starting, stopping, or turning on
a slope. If the tires lose traction,
disengage the blades and proceed slowly
straight down the slope.
Keep all movement
on the slopes slow
and gradual.
Do not make sudden
changes in speed or direction, which
could cause the machine to roll over.
Use extra care while operating machine with grass catchers or other attachments;
they can affect the stability
of the machine. Do no use on steep
slopes.
Do not try to stabilize the machine by
putting your foot on the ground.
Do not mow near drop-offs,
ditches,
or embankments.
The machine could
suddenly roll over if a wheel is over the
edge or if the edge caves in.
II1. CHILDREN
Tragic accidents
can occur if the operator
is not alert to the presence
of children.
Children are often attracted to the machine
and the mowing activity.
that children
will remain
saw them.
•
•
•
•
•
•
Before and while backing, look behind
and down for small children.
backed over by the machine.
Never allow children to operate
machine.
the
Use extra care when approaching
blind
corners, shrubs, trees, or other objects
that may block your view of a child.
IV, TOWING
•
•
Tow only with a machine that has a
hitch designed for towing. Do not attach towed equipment
except at the
hitch point.
Follow the manufacturer's
recom-
•
mendation
for weight limits for towed
equipment
and towing on slopes.
Never allow children or others in or on
•
•
towed equipment.
On slopes, the weight of the towed
equipment
may cause loss of traction
and loss of control.
Travel slowly
to stop.
and allow extra distance
V. SERVICE
SAFE
HANDLING
OF GASOLINE
To avoid personal injury or property
damage, use extreme care in handling
gasoline. Gasoline is extremely flammable
and the vapors are explosive.
•
Extinguish all cigarettes,
cigars, pipes,
and other sources of ignition.
•
Use only approved gasoline container.
•
Never remove gas cap or add fuel with
the engine running. Allow engine to
cool before refueling.
•
Never fuel the machine indoors.
•
Never store the machine or fuel con-
Never assume
where you last
Keep children out of the mowing area
and in the watchful care of a responsible adult other than the operator.
Be alert and turn machine off if a child
enters the area.
Never carry children, even with the
blades shut off. They may fall off and
be seriously injured or interfere with
safe machine operation.
Children who
have been given rides in the past may
suddenly
appear in the mowing area
for another ride and be run over or
•
tainer where there is an open flame,
spark, or pilot light such as on a water
heater or other appliances.
Never fill containers inside a vehicle
or on a truck or trailer bed with plastic
liner. Always place containers on the
ground away from your vehicle when
filling.
•
Removegas-poweredequipmentfrom
the truck or trailer and refuel it on the
ground. If this is not possible,then
refuelsuch equipmentwith a portable
container,rather than from a gasoline
dispensernozzle.
Keepthe nozzle in contactwith the rim
of the fuel tank or containeropening at
all times until fueling is complete.Do
not use a nozzle lock-opendevice.
If fuel is spilled on clothing, change
clothing immediately.
Neveroverfill fuel tank. Replacegas
cap and tightensecurely.
•
•
•
GENERAL
•
•
•
•
•
SERVICE
•
Never operate machine in a closed
area.
Keep all nuts and bolts tight to be sure
the equipment
is in safe working condition.
Never tamper with safety devices.
•
•
•
•
Check their proper operation regularly.
Keep machine free of grass, leaves, or
other debris build-up.
Clean oil or fuel
spillage and remove any fuel-soaked
debris. Allow machine to cool before
storing.
If you strike a foreign object, stop and
inspect the machine. Repair, if necessary, before restarting.
Never make any adjustments
or repairs
with the engine running.
Check grass catcher components
and
the discharge guard frequently
and
replace with manufacturer's
recommended parts, when necessary.
Mower blades are sharp. Wrap the
blade or wear gloves, and use extra
caution when servicing them.
Check brake operation frequently.
Adjust and service as required.
Maintain or replace safety and instruction labels, as necessary.
@@@@@
•
•
•
•
•
•
Be sure the area is clear of bystanders before operating.
Stop machine if
anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary. Always look down
and behind before and while backing.
Never carry children, even with the
blades shut off. They may fall off and
be seriously injured or interfere with
safe machine operation. Children who
have been given rides in the past may
suddenly appear in the mowing area
for another ride and be run over or
•
backed over by the machine.
Keep children out of the mowing area
and in the watchful care of a responsible adult other than the operator.
Be alert and turn machine off if a child
enters the area.
•
•
•
•
•
5
Before and while backing, look behind
and down for small children.
Mow up and down slopes (15 ° Max),
not across.
Choose a low ground speed so that
you will not have to stop or shift while
on the slope.
Avoid starting, stopping, or turning on
a slope. If the tires lose traction,
disengage the blades and proceed slowly
straight down the slope.
If machine stops while going uphill,
disengage
blades, shift into reverse
and back down slowly.
Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible.
PRODUCT
In the state of California
SPECIFICATIONS
Gasoline
Capacity
and Type:
3.5 Gallons
Unleaded
Regular
Oil Type
(API-SG-SL):
SAE 30 (above
SAE 5W-30
(Below 32°F)
Oil Capacity:
W/Filter:
3.5 Pints
W/O Filter: 3.0 Pints
Spark Plug:
(GAP: .030")
Ground
(MPH):
Champion
Speed
RC12YC
Forward:
Reverse:
Tire Pressure:
Front:
Rear:
Charging
3 Amps
5 Amps
System:
32°F)
5.5
2.4
14 PSI
10 PSI
Battery
Headlights
Battery:
Amp/Hr:
Min. CCA:
Case Size:
Blade Bolt
Torque:
27-35
28
230
U1R
Ft. Lbs.
CONGRATULATIONS
on your purchase
of a new tractor. It has been designed,
engineered
and manufactured
to give
you the best possible dependability
and
performance.
Should you experience
any problem you
cannot easily remedy, please contact a
Sears or other qualified service center.
We have competent, well-trained
technicians and the proper tools to service or
repair this tractor.
Please read and retain this manual. The
instructions
will enable you to assemble
and maintain your tractor properly. Always
observe the "SAFETY RULES".
CUSTOMER
RESPONSIBILITIES
• Read and observe the safety rules.
• Follow a regular schedule in maintaining, caring for and using your tractor.
• Follow the instructions
under"Maintenance" and "Storage"
owner's manual.
sections
of this
AI:_WARNING:
This tractor is equipped
with an internal combustion
engine and
should not be used on or near any unimproved forest-covered,
brush-covered
or
grass-covered
land unless the engine's
exhaust system is equipped with a spark
arrester meeting applicable
local or state
laws (if any). If a spark arrester is used, it
should be maintained
in effective working
order by the operator.
the above
is re-
quired by law (Section 4442 of the California Public Resources
Code). Other states
may have similar laws. Federal laws apply
on federal lands. A spark arrester for the
muffler is available through your nearest
Sears service center (See REPAIR PARTS
section of this manual).
REPAIR
PROTECTION
AGREEMENTS
Congratulations
on making a smart purchase. Your new Craftsman®
product is
designed and manufactured
for years of
dependable
operation. But like all products, it may require repair from time to
time. That's when having a Repair Protection Agreement
can save you money and
aggravation.
Purchase a Repair Protection Agreement
now and protect yourself from unexpected
hassle and expense.
Here's what's included in the Agreement:
•
Expert service
by our 12,000 profesional repair specialists.
•
Unlimited
service and no charge for
parts and labor on all covered repairs.
•
Product
replacement
if your covered
product can't be fixed.
•
Discount
of 10% from regular price of
service and service-related
parts not
covered by the agreement;
also, 10%
off regular price of preventive maintenance check.
•
Fast help by phonephone support
from a Sears technician on products
requiring in-home repair, plus convenient repair scheduling.
Once you purchase the Agreement,
a
simple phone call is all that it takes for you
to schedule service. You can call anytime
day or night, or schedule a service appointment online.
Sears has over 12,000 professional
repair
specialists,
who have access to over 4.5
million quality parts and accessories.
That's the kind of professionalism
you can
count on to help prolong the life of your
new purchase for years to come. Purchase your Repair Protection Agreement
today!
Some limitations
and exclusions
apply.
For prices and additional
information
call 1-800-827-6655.
SEARS
INSTALLATION
SERVICE
For Sears professional
installation
of
home appliances,
garage door openers,
water heaters, and other major home
items, in the U.S.A. call 1-800-4-MYHOME®
Steering
Steering
Wheel Insert
Wheel
(1) Large Flat Washer
Wheel Adapter
Steering
Steering
Boot
(1) 5/16 Lock Washer
(1) Hex Bolt
5/16-18 x 4
R
Seat
_
(1) Washer
17/32 x 1-3/16 x 12
Gauge
_7{_9 (1) Knob
For Future Use
Keys
Slope Sheet
Your new tractor has been assembled
at the factory with the exception of those parts left
unassembled
for shipping purposes. To ensure safe and proper operation of your tractor
all parts and hardware you assemble must be tightened securely. Use the correct tools
as necessary
to insure proper tightness.
TOOLS REQUIRED
A socket wrench
easier. Standard
are listed below.
FOR
ASSEMBLY
set will make assembly
wrench sizes you need
i_
c._._
I
(1) 3/4" wrench
(1) Pliers
(1) 1/2" wrench
(1) Utility knife
(1) Tire pressure
gauge
When right or left hand is mentioned
in
this manual, it means, from your point of
view, when you are in the operating position (seated behind the steering wheel).
TO REMOVE TRACTOR
CARTON
UNPACK CARTON
5/16 Hex Bolt
5/16 Lock Washer
-,
Large Flat
Washer
FROM
1. Remove all accessible loose parts and
parts boxes from carton.
2. Cut along dotted lines on all four panels of carton. Remove end panels and
lay side panels flat.
3. Check for any additional loose parts or
cartons and remove.
BEFORE
REMOVING
TRACTOR
FROM SKID
ATTACH STEERING WHEEL
ASSEMBLE EXTENSION SHAFT AND
BOOT
1. Slide extension shaft onto lower steering shaft.
2. Place tabs of steering boot over tab
slots in dash and push down to secure.
IMPORTANT:
Check for and remove any
staples in skid that may puncture tires
where tractor is to roll off skid.
INSTALL
Adjust
knob.
3.
4.
5.
6.
7.
8.
STEERING
Position
WHEEL
front wheels
of the tractor
so
they are pointing straight forward.
Remove steering wheel adapter from
steering wheel and slide adapter onto
steering shaft extension.
Position steering wheel so cross bars
are horizontal
(left to right) and slide
inside boot and onto adapter.
Assemble large flat washer, 5/16 lock
washer, 5/16 hex bolt and tighten
securely.
Snap steering wheel insert into center
of steering wheel.
Remove protective materials from tractor hood and grill.
INSTALL
SEAT
seat before
tightening
adjustment
1.
Remove adjustment
knob and flat
washer securing seat to cardboard
packing and set aside for assembly of
seat to tractor.
2. Pivot seat upward and remove from
the cardboard packing. Remove the
cardboard packing and discard.
3. Place seat on seat pan so head of
shoulder bolt is positioned
over large
slotted hole in pan.
4. Push down on seat to engage shoulder
bolt in slot and pull seat towards rear of
tractor.
5.
Pivot seat and pan forward and assemble adjustment
knob and flat
washer loosely. Do not tighten.
6. Lowerseat into operatingpositionand
sit in seat.
7. Slide seat until a comfortableposition
is reachedwhich allows you to press
clutch/brakepedal all the way down.
8. Get off seat without movingits adjusted position.
9. Raise seat and tightenadjustment
knobsecurely.
NOTE: You may now roll or drive your
tractor off the skid. Follow the appropriate
instruction below to remove the tractor
from the skid.
TO ROLL
Operation
function
2.
Seat
for
SKID
location
and
controls)
po-
3.
4.
mission disengaged"
position (See "TO
TRANSPORT"
in the Operation section
of this manual).
Roll tractor forward off skid.
5.
Flat Washer
(See
Release parking brake by depressing
clutch/brake
pedal.
Place freewheel
control in "trans-
Bolt
Remove banding
shield up against
holding
tractor.
deflector
TO DRIVE TRACTOR
OFF SKID (See
Operation
section for location and
function
of controls)
\
CHECK
section
of
OFF
1. Press lift lever plunger and raise
attachment
lift lever to its highest
sition.
Seat
Adjustment
TRACTOR
Knob
BATTERY
1. Lift hood to raised position.
NOTE: If this battery is put into service
after month and year indicated on label
(label located between terminals)
charge
battery for minimum of one hour at 6-10
amps. (See "BATTERY"
in Maintenance
section of this manual for charging instructions).
'
L-_bel
_WARNING:
Before starting, read, understand and follow all instructions in the
Operation section of this manual. Be sure
tractor is in a well-ventilated area. Be sure
the area in front of tractor is clear of other
people and objects.
1. Be sure all the above assembly steps
have been completed.
2. Check engine oil level and fill fuel tank
with gasoline.
3. Place freewheel control in "transmission engaged" position. (See "TO
TRANSPORT" in the Operation section
of this manual).
4. Sit on seat in operating position,
depress clutch/brake pedal and set the
parking brake.
5. Place motion control lever in neutral
(N) position.
6. Press lift lever plunger and raise
attachment lift lever to its highest position.
7. Start the engine. After engine has
started, move throttle control to idle
position.
8. Release parking brake.
9. Slowly move the motion control lever
forward and slowly drive tractor off
skid.
10.Apply brake to stop tractor, set parking
brake and place motion control lever in
neutral position.
11.Turn ignition key to "STOP" position.
9 Continue with the instructions that follow.
CHECKTIRE
PRESSURE
_CHECKLIST
The tires on your tractor were overinflated
at the factory for shipping purposes.
Correct tire pressure is important for best
cutting performance.
• Reduce tire pressure to PSI shown in
"PRODUCT
SPECIFICATIONS"
section
of this manual.
CHECK
DECK
LEVELNESS
For best cutting results, mower housing should be properly leveled. See "TO
LEVEL MOWER HOUSING"
in the Service
and Adjustments
section
of this manual.
CHECK FOR PROPER
OF ALL BELTS
POSITION
See the figures that are shown for replacing motion and mower blade drive belts
in the Service and Adjustments section
of this manual. Verify that the belts are
routed correctly.
CHECK
BRAKE
SYSTEM
After you learn how to operate your tractor, check to see that the brake is properly
adjusted.
See "TO ADJUST BRAKE" in
the Service and Adjustments
section of
this manual.
Before you operate your new tractor, we
wish to assure that you receive the best
performance
and satisfaction
from this
quality product.
Please review the following checklist:
,/ All assembly
instructions
have been
completed.
,/No remaining loose parts in carton.
,/Battery
is properly prepared and
charged.
(Minimum
1 hour at 6 amps).
,/Seat
is adjusted comfortably
and tightened securely.
,/All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).
,/Be sure mower deck is properly leveled
side-to-side/front-to-rear
for best cutting
results. (Tires must be properly inflated
for leveling).
v" Check mower and drive belts. Be sure
they are routed properly around pulleys
and inside all belt keepers.
v" Check wiring. See that all connections
are still secure and wires are properly
clamped.
v" Before driving tractor, be sure freewheel
control is in "transmission
engaged"
position (see "TO TRANSPORT"
in the
Operation section of this manual).
While learning how to use your tractor, pay
extra attention to the following important
items:
v" Engine oil is at proper level.
v" Fuel tank is filled with fresh, clean, regular unleaded gasoline.
v" Become familiar with all controls - their
location and function.
Operate them
before you start the engine.
v" Be sure brake system is in safe operating condition.
v" Be sure Operator Presence System
and Reverse Operation System (ROS)
are working properly (See the Operation and Maintenance
sections in this
manual).
v" It is important to purge the transmission
before operating your tractor for the first
time. Follow proper starting and transmission purging instructions
(See "TO
START ENGINE" and "PURGE TRANSMISSION"
in the Operation
this manual).
10
section
of
These symbols may appear on your tractor
Learn and understand
their meaning.
R
N
H
REVERSE
NEUTRAL
HIGH
or in literature
supplied
LOW
with the product.
SLOW
IGNITION
6
ENGINE OFF
6
REVERSE
OPERATION
SYSTEM (ROS)
ENGINE ON
6
ENGINE START
PARKING
BRAKE
SWITCH
@
PARKING BRAKE
LOCKED
PARKING BRAKE
UNLOCKED
4'
OVER TEMP
LIGHT
FUEL
ATTACHMENT
CLUTCH DISENGAGED
OIL PRESSURE
ATTACHMENT
CLUTCH ENGAGED
BATTERY
DANGER, KEEP HANDS
AND FEET AWAY
FORWARD
MOWER
KEEP AREA CLEAR
HEIGHT
MOWER
LIFT
SLOPE HAZARDS
(SEE SAFETY
RULES SECTION)
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
LIGHTS ON
WARNING
hazard
which,
if not avoided,
could result indicates
in death a or
serious
injury.
FREE WHEEL
(Automatic Models only)
CAUTION
which, ifinjury.
not avoided,
might resultindicates
in minora hazard
or moderate
&
CAUTION when used without the alert symbol,
indicates a situation that could result in damage
to the tractor and/or engine.
Failure to follow instructions
could result in serious
REVERSE
injury or
death. The safety alert symbol
is used to identify safety information about hazards which can
result in death, serious injury
and/or property damage.
4;II//IIN_/,,
HOT SURFACES indicates
if not avoided, could result
and/or property damage.
a hazard which,
in death, serious
FIRE indicates a hazard which, if not avoided,
could result in death, serious injury and/or
property damage.
11
injury
KNOWYOUR
TRACTOR
READTHIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATINGYOUR
TRACTOR
Compare the illustrations with your tractor to familiarize yourself with the locations of
various controls and adjustments. Save this manual for future reference.
Ammeter
Attachment
Clutch Lever
Ignition Switch
ROS "ON" Position
Lift Lever Plunger
Light Switch
"'-.
Attachment
Lift Lever
Throttle/Choke
Control
Clutch/Brake
Pedal
"'" " .......
Height
Adjustment
Indicator
__"
Freewheel
Control
Parking Brake Lever
Motion Control
Lever
02815
LSW
Our tractors conform to the safety standards
American
National Standards
Institute.
AMMETER - Indicates charging (+) or
discharging (-) of battery.
ATTACHMENT CLUTCH LEVER - Used
to engage the mower blades, or other attachments mounted to your tractor.
ATTACHMENT LIFT LEVER - Used to
raise, lower, and adjust the mower deck or
other attachments mounted to your tractor.
CLUTCH/BRAKE
PEDAL - Used for
declutching and braking the tractor and
starting the engine.
FREEWHEEL CONTROL - Disengagages
transmission for pushing or slowly towing
the tractor with the engine off.
IGNITION SWITCH - Used for starting and
stopping the engine.
LIFT LEVER
of the
PLUNGER
- Used to release
attachment
lift lever when changing its
position.
LIGHT SWITCH - Turns the headlights on
and off.
MOTION CONTROL
LEVER - Selects the
speed and direction of tractor.
PARKING BRAKE LEVER - Locks
clutch/
brake pedal into the brake position.
REVERSE
OPERATION
SYSTEM (ROS)
"ON" POSITION
- Allows operation of
mower deck or other powered attachment
while in reverse.
THROTTLE/CHOKE
CONTROLUsed
for starting
12
and controlling
engine
speed.
The operation of any tractor can result in foreign objects thrown into the
eyes, which can result in severe eye damage.
Always wear safety glasses
or eye shields while operating your tractor or performing
any adjustments
or repairs. We recommend
standard safety glasses or a wide vision safety
mask worn over spectacles.
HOW TO USE YOUR TRACTOR
TO SET PARKING
IMPORTANT:
Leaving the ignition switch
in any position other than "STOP" will
cause the battery to discharge
and go
dead.
NOTE: Under certain conditions when
BRAKE
Your tractor is equipped with an operator
presence sensing
switch. When engine
is running, any attempt by the operator
to leave the seat without first setting the
parking brake will shut off the engine.
1. Depress clutch/brake
pedal all the way
down and hold.
2. Pull parking brake lever up and release
pressure from clutch/brake
pedal.
Pedal should remain in brake position.
Make sure parking brake will hold tractor secure.
Attachment Clutch Lever
"Engaged" Position
Throttle/
Choke
nition Key
tractor is standing idle with the engine running, hot engine exhaust gases may cause
"browning" of grass. To eliminate this possibility, always stop engine when stopping
tractor on grass areas.
_,CAUTION:
Always stop tractor completely, as described
above, before leaving
the operator's
position.
TO USE THROTTLE
Always operate engine at full throttle.
• Operating engine at less than full
throttle reduces the battery charging
rate.
"Disengaged"
Position
"Brake"
• Full throttle offers the best bagging
mower performance.
Motion Control
TO MOVE
f_
Clutch/
Brake
Pedal
"Disengaged"
- Position
Parking Brake
"Engaged"
Position
BLADES
2.
3.
-
DRIVE
-
does not return to neutral (N) position
when the clutch/brake
pedal is depressed.
-
• Move throttle control between half and
full speed (fast) position.
NOTE:
Failure to move throttle control
between half and full speed (fast) position, before stopping, may cause engine to
"backfire".
• Turn ignition key to "STOP" position and
remove key. Always remove key when
leaving tractor to prevent unauthorized
use.
• Never use choke to stop engine.
BACKWARD
MOWER
lever to
CUTTING
HEIGHT
The position of the attachment
lift lever
determines
the cutting height.
• Grasp lift lever.
• Press plunger with thumb and move
lever to desired position.
The cutting
height range is approximately 1-1/2 to 4". The heights are measured from the ground to the blade tip with
the engine not running. These heights
are approximate
and may vary depending
upon soil conditions,
height of grass and
types of grass being mowed.
• The average lawn should be cut to approximately
2-1/2 inches during the cool
season and to over 3 inches during hot
months.
For healthier and better look-
• To stop ground drive, depress clutch/
brake pedal all the way down.
• Move motion control lever to neutral (N)
position.
IMPORTANT:
The motion control lever
ENGINE
AND
neutral (N) position.
Release parking brake.
Slowly move motion control
desired position.
TO ADJUST
• To stop mower blades, move attachment
clutch lever to "DISENGAGED"
position.
GROUND
FORWARD
and
The direction and speed of movement
is
controlled
by the motion control lever.
1. Start tractor with motion control lever in
STOPPING
MOWER
CONTROL
ing lawns, mow often and after moderate growth.
• For best cutting performance,
grass
over 6 inches in height should be
mowed twice. Make the first cut rela-
13
tively high; the second
to desired
height.
TO ADJUST
GAUGE
WHEELS
Gauge wheels
are properly adjusted
when they are slightly off the ground when
mower is at the desired cutting height in
operating position. Gauge wheels then
keep the deck in proper position to help
prevent scalping in most terrain conditions.
NOTE: Adjust gauge wheels with tractor
on a flat level surface.
1. Adjust mower to desired cutting height
(See "TO ADJUST MOWER CUTTING
HEIGHT" in this section of manual).
2. With mower in desired height of cut
position, gauge wheels should be
assembled
so they are slightly off the
ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8
washer, and 3/8-16 Iocknut and tighten
securely.
3. Repeat for opposite side, installing
gauge wheel in same adjustment
hole.
OPERATING
Your tractor is equipped with a Reverse
Operation System (ROS). Any attempt by
the operator to travel in the reverse direction with the attachment
clutch engaged
will shut off the engine unless the ignition
key is placed in the ROS "ON" position.
_,WARNING:
Backing up with the attachment clutch engaged while mowing
is strongly discouraged.
Turning the ROS
"ON", to allow reverse operation with the
attachment
clutch engaged, should only
be done when the operator decides it is
necessary
to reposition the machine with
the attachment
engaged. Do not mow in
reverse
unless absolutely
necessary.
Gauge
Wheel
Mountinc
Locknut
Bolt
Gauge Wheel
TO OPERATE
MOWER
attachment
clutch
USING THE REVERSE
SYSTEM -
OPERATION
1.
lever to neutral
2.
Your tractor is equipped with an operator
presence sensing switch. Any attempt
by the operator to leave the seat with the
engine running and the attachment
clutch
engaged will shut off the engine. You must
remain fully and centrally positioned
in the
seat to prevent the engine from hesitating
or cutting off when operating your equipment on rough, rolling terrain or hills.
1. Select desired height of cut.
2. Start mower blades by engaging attachment clutch control.
TO STOP MOWER BLADES disengage
IN REVERSE
3.
4.
5.
Move motion
control
(N) position.
With engine running, turn ignition key
counterclockwise
to ROS "ON" position.
Look down and behind before backing
up.
Slowly move motion control lever to
reverse (R) position to start movement.
When use of the ROS is no longer
needed, turn the ignition key clockwise
to engine "ON" position.
ROS "ON" Position
control.
_CAUTION:
Do not operate the mower
without either the entire grass catcher,
on mowers so equipped, or the deflector
shield in place.
14
Engine "ON" Position
(Normal Operating)
TO OPERATE
ON HILLS
_ILWARNING:
Do not drive up or down
hills with slopes greater than 15 ° and do
not drive across any slope. Use the slope
guide at the back of this manual.
• Choose the slowest speed before starting up or down hills.
• Avoid stopping or changing speed on
hills.
• If slowing is necessary, move throttle
control lever to slower position.
• If stopping is absolutely
necessary, push
clutch/brake
pedal quickly to brake position and engage parking brake.
• Move motion control lever to neutral (N)
position.
IMPORTANT:
The motion control lever
does not return to neutral (N) position
when the clutch/brake
pedal is depressed.
• To restart movement,
slowly release
parking brake and clutch/brake
pedal.
• Slowly move motion control lever to
slowest setting.
• Make all turns slowly.
TO TRANSPORT
When pushing or
sure to disengage
freewheel
control
Freewheel
control
drawbar of tractor.
towing your tractor, be
transmission
by placing
in freewheeling
position.
is located at the rear
1. Raise attachment
lift to highest position
with attachment
lift control.
2. Pull freewheel
control out and down
into the slot and release so it is held in
the disengaged
position.
• Do not push or tow tractor
two (2) MPH.
• To re-engage transmission,
above procedure.
Transmission
Transmission
at more than
reverse
Engaged
Disengaged
NOTE: To protect hood from damage
when transporting
your tractor on a truck
or a trailer, be sure hood is closed and
secured to tractor. Use an appropriate
means of tying hood to tractor (rope, cord,
etc.).
TOWING
MENTS
CARTS
AND
OTHER
ATTACH-
Tow only the attachments
that are recommended by and comply with specifications
of the manufacturer
of your tractor. Use
common sense when towing. Too heavy
of a load, while on a slope, is dangerous.
Tires can lose traction with the ground and
cause you to lose control of your tractor.
BEFORE
STARTING
THE ENGINE
CHECK
ENGINE
OIL LEVEL
The engine in your tractor has been
shipped, from the factory, already filled
with summer weight oil.
1. Check engine oil with tractor on level
ground.
2. Remove oil fill cap/dipstick
and wipe
clean, reinsert the dipstick and screw
cap tight, wait for a few seconds,
remove and read oil level. If necessary,
add oil until "FULl" mark on dipstick is
reached.
Do not overfill.
• For cold weather operation you should
change oil for easier starting ((See the
oil viscosity chart in the Maintenance
section of this manual).
• To change engine oil, see the Maintenance section in this manual.
ADD GASOLINE
• Fill fuel tank to bottom of tank filler neck.
Do not overfill. Use fresh, clean, regular
unleaded gasoline with a minimum of
87 octane. (Use of leaded gasoline will
increase carbon and lead oxide deposits
and reduce valve life). Do not mix oil
with gasoline. Purchase fuel in quantities that can be used within 30 days to
assure fuel freshness.
_CAUTION:
Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
IMPORTANT:
When operating in temperatures below 32°F(0°C),
use fresh, clean
winter grade gasoline to help insure good
cold weather starting.
CAUTION:
Alcohol blended fuels (called
gasohol or using ethanol or methanol)
can
attract moisture which leads to separation
and formation of acids during storage. Acidic gas can damage the fuel system of an
engine while in storage.
To avoid engine problems, the fuel system
should be emptied before storage of 30
days or longer. Drain the gas tank, start
the engine and let it run until the fuel lines
and carburetor
are empty. Use fresh fuel
next season. See Storage Instructions
for
additional information.
Never use engine or carburetor
cleaner
15P r°ducts in the fuel tank or permanent
damage may occur.
TO START
AUTOMATIC
ENGINE
When starting the engine for the first time
or if the engine has run out of fuel, it will
take extra cranking time to move fuel from
the tank to the engine.
1. Be sure freewheel control is in the
transmission engaged position.
2. Sit on seat in operating position,
depress clutch/brake pedal and set
parking brake.
3. Place motion control lever in neutral
(N) position.
4. Move attachment clutch to disengaged
position.
5. Move throttle control to choke position.
NOTE: Before starting, read the warm
and cold starting procedures below.
6. Insert key into ignition and turn key
clockwise to start position and release
key as soon as engine starts. Do
not run starter continuously for more
than fifteen seconds per minute. If the
engine does not start after several
attempts, move throttle control to fast
position, wait a few minutes and try
again. If engine still does not start,
move the throttle control back to the
choke position and retry.
WARM WEATHER
STARTING
(50 ° F and
above)
7. When engine starts, move the throttle
control to the fast position.
• The attachments
and ground drive can
now be used. If the engine does not
accept the load, restart the engine and
allow it to warm up for one minute using
the choke as described
above.
COLD WEATHER
below)
7.
STARTING
( 50 ° F and
When engine starts, allow engine
to run with the throttle control in the
choke position until the engine runs
roughly, then move throttle control
to fast position. This may require an
engine warm-up period from several
seconds to several minutes, depending
on the temperature.
TRANSMISSION
WARM
UP
Before driving the unit in cold weather,
the transmission
should be warmed up as
follows:
1.
2.
Be sure the tractor is on level ground.
Place the motion control lever in
3.
neutral. Release the parking brake
and let the clutch/brake
slowly return
to operating position.
Allow one minute for transmission
to
warm up. This can be done during
the engine warm up period.
• The attachments
can also be used during the engine warm-up
period after the
transmission
has been warmed up.
NOTE:
If at a high altitude (above 3000
feet) or in cold temperatures
(below 32 F)
the carburetor
fuel mixture may need to
be adjusted for best engine performance.
(See "TO ADJUST CARBURETOR"
in the
Service and Adjustments
section of this
manual.)
PURGE
TRANSMISSION
To ensure proper operation and performance,
it is recommended
that the
transmission
be purged before operating
tractor for the first time. This procedure will
remove any trapped air inside the transmission which may have developed
during
shipping of your tractor.
IMPORTANT:
Should your transmission
require removal for service or replacement, it should be purged after reinstallation before operating the tractor.
1. Place tractor safely in an area that is
flat for approximately
80 feet in front of
the tractor and set the parking brake.
2. Sitting in the tractor seat, start engine.
After the engine is running, move
throttle control to slow position. With
motion control lever in neutral (N)
position, slowly disengage
clutch/brake
pedal.
3. Slowly move motion control lever to
full forward position and hold for five
(5) seconds, or approximately
40 feet.
Slowly move lever to full reverse position and hold for five (5) seconds, or
approximately
20 feet. After the tractor
moves approximately
20 feet in reverse
return the motion control lever to the
neutral (N) position. Repeat this procedure three (3) times.
Your transmission
is now purged and now
ready for normal operation.
16
MOWING
TIPS
• Mower should be properly leveled for
best mowing performance.
See "TO
LEVEL MOWER HOUSING"
in the
Service and Adjustments
section of this
manual.
• The left hand side of mower should be
used for trimming.
• Drive so that clippings are discharged
onto the area that has already been cut.
Have the cut area to the right of the tractor. This will result in a more even distribution of clippings and more uniform
cutting.
• When mowing large areas, start by
turning to the right so that clippings will
discharge
away from shrubs, fences,
driveways, etc. After one or two rounds,
mow in the opposite direction making
left hand turns until finished.
f
1
-
J
00272
• If grass is extremely tall, it should be
mowed twice to reduce load and possible fire hazard from dried clippings.
Make first cut relatively high; the second
to the desired height.
• Do not mow grass when it is wet. Wet
grass will plug mower and leave undesirable clumps. Allow grass to dry before
mowing.
• Always
operate engine at full throttle
when mowing
to assure better mowing performance
and proper discharge
of material.
Regulate ground speed by
selecting a low enough gear to give the
mower cutting performance
as well as
the quality of cut desired.
• When operating attachments,
select a
ground speed that will suit the terrain
and give best performance
of the attachment
being used.
17
/_/_X'x_'_/_
/__/_
FILL IN DATES
AS YOU COMPLETE
REGULAR
SERVICE
Check Operator
ROS Systems
DATES
_
Presence
and
I_
Check for Loose Fasteners
Mower
If
ll_s
A
Sharpen/Replace
C
Lubrication
0
Check
Battery Level
1_4
Clean
Battery and Terminals
ll_
R
Blades
I_
I_
If
Cooling
Check V-Belts
Engine
Change
if
Oil Level
Oil (with oil filter)
Engine
Oil (without
Change
N
Clean
Air
G
Clean
Air Screen
E
Clean
I_
Ill1,2
oil filter)
I_
_2
1_2
v'
Arrester
Oil Filter (If equipped)
Engine
If
11_1,2
Filter
Muffler/Spark
Replace
If
Engine
E
Inspect
Cooling
_1,2
Fins
I_
2
Replace
Spark Plug
If
Replace
Air Filter Paper Cartridge
1_2
Replace
Fuel Filter
1 - Change
more often when operating
in high ambient
temperatures.
2 - Service more often when operating
GENERAL
under
a heavy
in dirty
or dusty
load
or
If
3 - Replace
blades more often when mowing
in sandy soil.
4 - Not required
if equipped
with maintenance-tree
battery.
5 - Tighten front axle pivot bolt to 35 ft.-Ibs, maximum.
Do not overtighten,
conditions,
RECOMMENDATIONS
LUBRICATION
The warranty on this tractor does not
cover items that have been subjected to
operator abuse or negligence.
To receive
full value from the warranty, operator
must maintain tractor as instructed in this
manual.
Some adjustments
will need to be made
periodically
to properly maintain your
tractor.
At least once a season, check to see if
you should make any of the adjustments
described
in the Service and Adjustments
section of this manual.
Spindle
Zerk
_Front Wheel
Bearing
Zerk
_Front Wheel
....
::'
ng Zerk
@Engine ,_
t
_
A new spark plug and clean air filter
assure proper air-fuel mixture and help
your engine run better and last longer.
EACH
CHART
dP S_
Zerk
• At least once a year you should replace
the spark plug, clean or replace air filter,
and check blades and belts for wear.
BEFORE
If
11_3
Chart
Check Transaxle
Check
"
/_r/_'_VSERVICE
Check
BrakePressure
Operation
Check Tire
T
R
_
_/_/O.Oq.
_"
_4
(1_ General
@ REFER
USE
Purpose
TO
01964
_I
Grease
Maintenance
"ENGINE"
SECTION
IMPORTANT: Do not oil or grease the
pivot points which have special nylon
bearings. Viscous lubricants will attract
dust and dirt that will shorten the life of the
self-lubricating bearings. If you feel they
must be lubricated, use only a dry, powdered graphite type lubricant sparingly.
1.
2.
3.
4.
Check engine oil level.
Check brake operation.
Check tire pressure.
Check operator presence and
ROS systems for proper operation.
5. Check for loose fasteners.
18
ROS "ON" Position
TRACTOR
Always observe safety rules when
forming any maintenance.
BRAKE OPERATION
per-
If tractor requires more than five (5) feet to
stop at highest speed in highest gear on a
level, dry concrete or paved surface, then
brake must be checked and adjusted. (See
"TO ADJUST BRAKE" in the Service and
Adjustments
TIRES
section
of this manual).
• Maintain proper air pressure in all tires
(See "PRODUCT
SPECIFICATIONS"
section of this manual).
• Keep tires free of gasoline, oil, or insect
control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
NOTE: To seal tire punctures and prevent
flat tires due to slow leaks, tire sealant
may be purchased
from your local parts
dealer. Tire sealant also prevents tire dry
rot and corrosion.
OPERATOR
PRESENCE
SYSTEM AND
REVERSE
OPERATION
SYSTEM
(ROS)
Be sure operator presence and reverse
operation systems are working properly.
If
your tractor does not function as described, repair the problem immediately.
• The engine should not start unless the
brake pedal is fully depressed,
and the
attachment
clutch control is in the disengaged
position.
CHECK OPERATOR
SYSTEM
OPERATION
• When the engine is running with the
ignition switch in the ROS "ON" position
and the attachment
clutch is engaged,
any attempt by the operator to shift into
reverse should NOT shut off the engine.
BLADE CARE
For best results mower blades must be kept
sharp. Replace bent or damaged blades.
BLADE
REMOVAL
1.
Raise mower to highest position to allow access to blades.
2. Remove blade bolt, lock washer and
flat washer securing blade.
3. Install new or resharpened
blade
with trailing edge up towards deck as
shown.
IMPORTANT:
To ensure proper assembly,
center hole in blade must align with star
on mandrel assembly.
4. Reassemble
blade bolt, lock washer
and flat washer in exact order as
shown.
5. Tighten blade bolt securely (27-35 Ft.
Lbs. torque).
IMPORTANT:
Blade bolt is heat treated.
If bolt needs replacing,
replace only with
approve bolt shown in the Repair Parts.
Trailing
Edge Up_
PRESENCE
• When the engine is running, any attempt by the operator to leave the seat
without first setting the parking brake
should shut off the engine.
• When the engine is running and the
attachment
clutch is engaged, any attempt by the operator to leave the seat
should shut off the engine.
• The attachment
clutch should never operate unless the operator is in the seat.
CHECK REVERSE
SYSTEM
Engine "ON" Position
(Normal Operating)
(ROS)
• When the engine is running with the ignition switch in the engine "ON" position
and the attachment
clutch is engaged,
any attempt by the operator to go into
reverse should shut off the engine.
Mandrel As., embly
Blade
Centel
Lock
TO SHARPEN
BLADE
NOTE: We do not recommend
sharpening blade - but if you do, be sure the
blade is balanced.
Care should be taken to keep the blade
balanced.
An unbalanced
blade will cause
excessive vibration and eventual damage
to mower and engine.
• The blade can be sharpened
with a file
or on a grinding wheel.
Do not attempt
to sharpen while on the mower.
• To check blade balance, you will need a
5/8" diameter steel bolt, pin, or a cone
balancer.
(When using a cone balancer,
follow the instructions
supplied with
19 balancer.)
• Inspect cooling fins for dirt, grass clippings and other materials.
To prevent
damage to seals, do not use compressed air or high pressure sprayer to
clean cooling fins.
TRANSAXLE
PUMP FLUID
NOTE: Do not use a nail for balancing
blade. The lobes of the center hole may
appear to be centered, but are not.
• Slide blade on to an unthreaded
portion
of the steel bolt or pin and hold the
bolt or pin parallel with the ground.
If
blade is balanced, it should remain in a
horizontal position.
If either end of the
blade moves downward,
sharpen the
heavy end until the blade is balanced.
5/8" Bolt or Pin_
The transaxle was sealed at the factory
and fluid maintenance
is not required for
the life of the transaxle.
Should the transaxle ever leak or require servicing, contact
a Sears or other qualified service center.
V-BELTS
Check V-belts
Blade
BATT E RY
Your tractor has a battery charging
which is sufficient for normal use.
system
How-
ENGINE
LUBRICATION
Only use high quality detergent oil rated
with API service classification
SG-SL. Select the oil's SAE viscosity grade according
to your expected operating temperature.
ever, periodic charging of the battery with
an automotive
charger will extend its life.
• Keep battery and terminals clean.
• Keep battery bolts tight.
• Keep small vent holes open.
• Recharge at 6-10 amperes for 1 hour.
NOTE: The original equipment
battery on
your tractor is maintenance
free. Do not
attempt to open or remove caps or covers.
Adding or checking level of electrolyte
is
not necessary.
BATTERY
SAE VISCOSITY
F
-20
c -10
0
-2_
TEMPERATURE
30
-15
32
GRADES
40
_
RANGE ANTICIPATED
60
1'0
100
10
OH vJs_
4_
chart1
e
NOTE: Although multi-viscosity
oils
(5W30, 10W30 etc.) improve starting in
cold weather, they will result in increased
oil consumption
when used above 32°F.
Check your engine oil level more frequently to avoid possible engine damage from
running low on oil.
Change the oil after every 50 hours of operation or at least once a year if the tractor
is not used for 50 hours in one year.
Check the crankcase oil level before starting
the engine and after each eight (8) hours of
operation. Tighten oil fill cap/dipstick securely
each time you check the oil level.
Corrosion
and dirt on the battery and
terminals can cause the battery to "leak"
power.
1. Remove terminal guard.
2. Disconnect
BLACK battery cable first
then RED battery cable and remove
battery from tractor.
3. Rinse the battery with plain water and
dry.
4. Clean terminals and battery cable ends
with wire brush until bright.
5. Coat terminals with grease or petroleum jelly.
6. Reinstall battery (See "REPLACING
BATTERY" in the SERVICE AND AD-
TO CHANGE
of this manual).
ENGINE
OIL
Determine
temperature
range expected
before oil change. All oil must meet API
service classification
SG-SL.
• Be sure tractor is on level surface.
The transmission
fan and cooling fins
should be kept clean to assure proper
cooling.
Do not attempt to clean fan or transmission while engine is running or while the
transmission
is hot. To prevent possible
damage to seals, do not use high pressure
water or steam to clean transaxle.
• Inspect cooling fan to be sure fan blades
are intact and clean.
80
_0
BEFORE NEXT OIL CHANGE
AND TERMINALS
JUSTMENTS
section
TRANSAXLE
COOLING
and wear
after 100 hours of operation and replace
if necessary. The belts are not adjustable.
Replace belts if they begin to slip from
wear.
Center Hole
TO CLEAN
for deterioration
• Oil will drain more freely when warm.
• Catch oil in a suitable container.
1.
2.
Remove oil fill cap/dipstick.
Be careful
not to allow dirt to enter the engine
when changing oil.
Remove yellow cap from end of drain
valve and install the drain tube onto the
fitting.
20
Oil Drain Valve
6. Align tabs on cover with slots in blower
housing and replace cover.
7. Hook handle on cover and push down
on handle to close.
IMPORTANT: Petroleum solvents, such
as kerosene, are not to be used to clean
the cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean
cartridge.
Closed
and
Locked
Position
Yellow Ca
Drain Tube
_
3.
4.
5.
6.
7.
8.
Unlock drain valve by pushing inward
slightly and turning counterclockwise.
To open, pull out on the drain valve.
After oil has drained completely,
close
and lock the drain valve by pushing
inward and turning clockwise
until the
pin is in the locked position as shown.
Remove the drain tube and replace the
cap onto the end of the drain valve.
Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill.
For approximate
capacity see "PRODUCT SPECIFICATIONS"
section of this
manual.
Use gauge on oil fill cap/dipstick
for
checking level. For accurate reading,
tighten dipstick cap securely onto the
tube before removing dipstick.
Keep oil
at "FULl" line on dipstick. Tighten cap
onto the tube securely when finished.
__
Cover
--I
Cartridge
Tabs
Slots
CLEAN
AIR SCREEN
Air screen must be kept free of dirt and
chaff to prevent engine damage from
overheating.
Clean with a wire brush or
compressed
air to remove dirt and stubborn dried gum fibers.
ENGINE OIL FILTER
Replace the engine oil filter every season
or every other oil change if the tractor is
used more than 100 hours in one year.
AIR
Handle
ENGINE
FILTER
COOLING
SYSTEM
Debris may clog the engine's air cooling system. Remove blower housing and
clean area shown to prevent overheating
and engine damage.
Your engine will not run properly using a
dirty air filter. Replace pre-cleaner
after
every 25 hours of operation or every
season.
Service paper cartridge every
100 hours of operation or every season,
whichever occurs first.
Air Screen
Service air cleaner more often under dusty
conditions.
1. Pull up on air filter cover handle and
rotate towards engine.
2. Remove cover.
3. Carefully remove air filter cartridge and
pre-cleaner
from base.
4. Clean base carefully to prevent debris
from falling into carburetor.
NOTE: If very dirty or damaged,
replace
cartridge.
5. Place new pre-cleaner
and cartridge
firmly in base.
21
Clean out chaff and debris
MUFFLER
CLEANING
Inspect and replace corroded muffler and
spark arrester (if equipped) as it could create a fire hazard and/or damage.
SPARK PLUG(S)
Replace spark plug(s) at the beginning
of each mowing season or after every
100 hours of operation, whichever occurs
first. Spark plug type and gap setting are
shown in "PRODUCT SPECIFICATIONS"
section of this manual.
• Clean engine, battery, seat, finish, etc.
of all foreign matter.
• Keep finished surfaces and wheels free
of all gasoline, oil, etc.
• Protect painted surfaces with automotive type wax.
We do not recommend
using a garden
hose or pressure washer to clean your
tractor unless the engine and transmission
covered to keep water out. Water in engine or transmission
will shorten the usful
life of your tractor. Use compressed
air or
a leaf blower to remove grass, leaves and
trash from tractor and mower.
IN-LINE
FUEL
FILTER
The fuel filter should be replaced once
each season.
If fuel filter becomes
clogged, obstructing
fuel flow to carburetor, replacement
is required.
1. With engine cool, remove filter and
plug fuel line sections.
2. Place new fuel filter in position in fuel
line with arrow pointing towards carburetor.
3. Be sure there are no fuel line leaks and
4.
clamps are properly positioned.
Immediately
wipe up any spilled
line.
gaso-
Fuel
22
WARNING:
SERVICE ORTOADJUSTMENTS:
AVOID SERIOUS
1.
2.
3.
4.
5.
6.
INJURY,
TRACTOR
TO REMOVE
PERFORMING
ANY
9.
Raise lift lever to raise suspension
arms. Slide mower out from under tractor.
IMPORTANT:
If an attachment
other than
the mower deck is to be mounted on the
MOWER
Mower will be easier
right side of tractor.
1. Place attachment
2.
BEFORE
Depress clutch/brake
pedal fully and set parking brake.
Place motion control lever in neutral (N) position.
Place attachment
clutch in "DISENGAGED"
position.
Turn ignition key to "STOP" and remove key.
Make sure the blades and all moving parts have completely
stopped.
Disconnect
spark plug wire from spark plug and place wire where it cannot
come in contact with plug.
GAGED" position.
Move attachment
to remove
clutch
from the
in "DISEN-
lift lever forward
tractor, remove the front links and hook
the clutch spring Into square hole in frame.
to
lower mower to its lowest position.
3. Roll belt off engine pulley.
4. Remove small retainer spring, and
remove clutch spring off pulley bolt.
5. Remove large retainer spring, slide
collar off and push housing guide out
of bracket.
TO INSTALL MOWER
1. Raise attachment lift lever to its highest
position.
2. Slide mower under tractor with deflector shield to right side of tractor.
3. Lower lift lever to its lowest position.
4. Connect front links to mower deck and
secure with retainer springs.
5. Connect suspension arms to rear
deck brackets and secure with retainer
springs.
6. Connect anti-sway bar to chassis
bracket and secure with retainer spring.
6.
Disconnect
anti-sway bar from chassis
bracket by removing retainer spring.
7. Disconnect
suspension
arms from rear
deck brackets by removing retainer
springs.
8. Disconnect
front links from deck by
removing retainer springs.
Small Retainer Spring
Clutch Spring
Small Retainer
Clutch
S
Engine
Pulley
Front Link
Retainer
Spring
Anti-Sway
Bar
Retainer Springs
(Both Sides)
Deflector
Housing
Guide
Retainer Spring
23
7.
8.
9.
• Before making any necessary adjustments, check that both front links are
equal in length.
• If links are not equal in length, adjust
one link to same length as other link.
• To lower front of mower loosen nut "E"
on both front links an equal number of
turns.
• When distance "D" is 1/8" to 1/2"
lower at front than rear, tighten nuts "F"
against trunnion on both front links.
• To raise front of mower, loosen nut "F"
from trunnion on both front links. Tighten
nut "E" on both front links an equal number of turns. The two front links must
remain equal in length.
• When distance "D" is 1/8" to 1/2" lower
at front than rear, tighten nut "F" against
trunnion on both front links.
• Recheck side-to-side adjustment.
Push clutch cable housing guide into
bracket, slide collar onto guide and
secure with large retainer spring.
Place flat washer and clutch spring on
idler pulley bolt and secure with small
retainer spring.
Install belt onto engine pulley.
TO LEVEL
MOWER
HOUSING
Adjust the mower while tractor is parked
on level ground or driveway.
Make sure
tires are properly inflated (See "PRODUCT SPECIFICATIONS"
section of this
manual).
If tires are over or underinflated,
you will not properly adjust your mower.
SIDE-TO-SIDE
ADJUSTMENT
• Raise mower to its highest position.
• At the midpoint of both sides of mower,
measure height from bottom edge of
mower to ground.
Distance "A" on both
sides of mower should be the same or
within 1/4" of each other.
Oo\_
• If adjustment
is necessary, make adjustment on one side of mower only.
• To raise one side of mower, tighten lift
link adjustment
nut on that side.
• To lower one side of mower, loosen lift
link adjustment
nut on that side.
NOTE:
Each full turn of adjustment
nut
will change mower height about 1/8".
• Recheck measurements
after adjusting.
Bottom edge
of mower to
0rouo0,
.....
oo, _
Mandrel
Both Fron,t Links Should be. E,qual in Length
Bottom edge of
mower to ground
Nut "F"
Trunnion
Arm
O
Lift Link
.............................................
Adjustment Nut -------
- --
FRONT-TO-BACK ADJUSTMENT
IMPORTANT:
Deck must be level side-to
side. If the following front-to-back adjustment is necessary, be sure to adjust both
front links equally so mower will stay level
side-to-side.
To obtain the best cutting results, the
mower housing should be adjusted so
that the front is approximately 1/8" to 1/2"
lower than the rear when the mower is in
its highest position.
Check adjustment on right side of tractor. Measure distance "D" directly in front
and behind the mandrel at bottom edge of
mower housing as shown.
Front Links
TO REPLACE MOWER BLADE DRIVE
BELT
The mower blade drive belt may be replaced without tools. Park the tractor on
level surface. Engage parking brake.
BELT REMOVAL
1.
2.
3.
24
-
Remove mower from tractor (See "TO
REMOVE MOWER" in this section of
manual).
Work belt off both mandrel pulleys
idler pulleys.
Pull belt away from mower.
and
BELT INSTALLATION
-
.
1. Work belt around both mandrel pulleys
and idler pulleys
2. Make sure belt is in all pulley grooves
and inside all belt guides.
3. Install mower (See "To Install Mower"
in this section of this manual).
Road test tractor for proper stopping
distance as stated above. Readjust
if necessary.
If stopping distance is
still greater than five (5) feet in highest
gear, further maintenance
is necessary. Replace brake pads or contact a
Sears or other qualified service center.
Mandrel
Idler
Ope raW_
Pulley
TO CHECK
TO REPLACE
AND
ADJUST
1.
2.
BRAKE
BELT REMOVAL
DRIVE
BELT
-
1.
Remove mower (See "TO REMOVE
MOWER" in this section of manual).
NOTE: Observe entire motion drive belt
and position of all belt guides and keepers.
2. Remove belt from stationary
idler and
clutching idler.
3. Remove belt downward from around
BRAKE
Park tractor on a level, dry concrete or
paved surface, depress clutch/brake
pedal all the way down and engage
parking brake.
Disengage
transmission
by placing
freewheel
control in "transmission
dis-
4.
5.
engaged" position. Pull freewheel
control out and into the slot and release so
engine pulley.
Pull belt slack toward rear of tractor.
Carefully remove belt upwards from
transmission
input pulley.
Remove belt from center span keeper
and pull belt away from tractor.
BELT INSTALLATION
it is held in the disengaged
position.
The rear wheels must lock and skid when
-
1. Carefully work new belt down onto the
input pulley.
2. Slide belt into the center span keeper.
3. Pull belt toward front of tractor and roll
you try to manually push the tractor forward. If the rear wheels rotate, the brake
needs to be adjusted or the pads need to
be replaced.
TO ADJUST
MOTION
Park the tractor on level surface.
Engage
parking brake. For assistance,
there is a
belt installation guide decal on bottom side
of left footrest.
Your tractor is equipped with an adjustable
brake system which is mounted on the
right side of the transaxle.
If tractor requires more than five (5) feet to
stop at highest speed in highest gear on a
level, dry concrete or paved surface, then
brake must be checked and adjusted.
TO CHECK
tamA"Nut
4.
BRAKE
1.
Depress clutch/brake
pedal all the way
down and engage parking brake.
2. Measure distance between brake operating arm and nut "A" on brake rod.
3. If distance is other than 1-9/16", loosen
jam nut and turn nut "A" until distance
becomes
1-9/16". Retighten jam nut
against nut "A".
4. Engage transmission
by placing
freewheel
control in "transmission
engaged" position.
5.
6.
25
around the top groove of engine pulley.
Install belt through stationary
idler and
clutching idler.
Make sure belt is in all pulley grooves
and inside all belt guides and keepers.
Install mower (See "TO INSTALL
MOWER" in this section of manual).
Engine Pulley
TRANSMISSION
REPLACEMENT
____
--I\
Clutching
Stationary
Center Span
Keeper.-------_
Transmission
REMOVAL/
Should your transmission
require removal for
service or replacement, it should be purged
after reinstallation and before operating the
tractor. See "PURGE TRANSMISSION"
in
the Operation section of this manual.
_[----_,-i _ I
II
II__--J--.[
TO ADJUST
MENT
_
STEERING
The front wheel
TRANSAXLE
MOTION CONTROL
VER NEUTRAL
ADJUSTMENT
LE-
The motion control lever has been preset
at the factory and adjustment
should not
be necessary.
1. Loosen adjustment
bolt in front of the
right rear wheel and lightly tighten.
2. Start engine and move motion control lever until tractor does not move
forward or backward.
3. Hold motion control lever in that position and turn engine off.
4. While holding motion control lever in
place, loosen the adjustment
bolt.
5. Move motion control lever to the neutral (N) (lock gate) position.
6. Tighten adjustment
bolt securely.
NOTE: If additional
clearance is needed
to get to adjustment
bolt, move mower
deck height to the lowest position.
After above adjustment
is made, if the
tractor still creeps forward or backward
while motion control lever is in neutral
position, follow these steps:
1. Loosen the adjustment
bolt.
2. Move the motion control lever 1/4
toe-in
and camber
are not
adjustable
on your tractor.
If damage has
occurred to affect the front wheel toe-in or
camber, contact
service center.
TO REMOVE
a Sears
WHEEL
or other qualified
FOR
REPAIRS
1.
2.
Block up axle securely.
Remove axle cover, retaining ring and
washers to allow wheel removal (rear
wheels have a square key - Do not lose).
3. Repair tire and reassemble.
NOTE: On rear wheels only: align
grooves in rear wheel hub and axle. Insert
square key.
4. Replace washers and snap retaining
ring securely in axle groove.
5. Replace axle cover.
NOTE: To seal tire punctures and prevent
flat tires due to slow leaks, purchase and
use tire sealant from Sears. Tire sealant
also prevents
tire dry rot and corrosion.
Washers
Retaining Ring
Axle Cover
to
1/2 inch in the direction it is trying to
creep.
Tighten adjustment
bolt securely.
Start engine and test.
If tractor still creeps, repeat above
steps until satisfied.
Motion Control
Lever
ALIGN-
If steering wheel crossbars
are not
horizontal
(left to right) when wheels are
positioned
straight forward, remove steering wheel and reassemble
with crossbars
horizontal.
Tighten securely.
FRONT WHEEL TOE-IN/CAM
BER
II__P_L
Input Pulley/_
3.
4.
5.
WHEEL
Lock
Gate
Adjustment
Bolt
TO START
TERY
ENGINE
WITH
A WEAK
BAT-
,_WARNING:
Lead-acid batteries generate explosive gases. Keep sparks, flame
and smoking materials away from batteries. Always wear eye protection when
around batteries.
If your battery is too weak to start the
engine, it should be recharged.
(See "BATTERY" in the MAINTENANCE
section of
26this
manual).
If "jumper cables" are used for emergency
starting, follow this procedure:
IMPORTANT:
Your tractor is equipped
with a 12 volt system. The other vehicle
must also be a 12 volt system. Do not use
your tractor battery to start other vehicles.
8.
9.
TO ATTACH
1. Connect
Terminal
Access
Door
_
2.
3.
2.
to the POSITIVE
(+) terminal of each
battery(A-B),
taking care not to short
against tractor chassis.
Connect one end of the BLACK cable
to the NEGATIVE
(-) terminal (C) of
fully charged battery.
Connect the other end of the BLACK
cable (D) to good chassis ground,
away from fuel tank and battery.
Cable
TO REPLACE
HEADLIGHT
BULB
1. Raise hood.
2. Pull bulb holder out of the hole in the
and
backside of the grill.
Replace bulb in holder and push bulb
holder securely back into the hole in
the backside of the grill.
4. Close hood.
INTERLOCKS
AND RELAYS
3.
Loose or damaged wiring may
your tractor to run poorly, stop
prevent it from starting.
• Check wiring.
See electrical
diagram in the Repair Parts
TO REPLACE
FUSE
02614
Fully Charged Battery
BATTERY
cause
running,
or
wiring
section.
Replace with 20 amp automotive-type
plug-in fuse. The fuse holder is located
behind the dash.
WARNING"
Do not short battery
terminals by allowing a wrench or any
other object to contact both terminals at
the same time. Before connecting
battery,
remove metal bracelets, wristwatch
bands,
rings, etc.
Positive terminal must be connected
first to prevent sparking from accidental
grounding.
1. Lift hood to raised position.
2. Remove terminal guard.
3. Disconnect
BLACK battery cable
then RED battery cable and carefully
remove battery from tractor.
4. Install new battery with terminals in
same position as old battery.
5. Reinstall terminal guard.
6. First connect RED battery cable to
positive (+) battery terminal with hex
bolt and keps nut as shown. Tighten
securely.
7. Connect BLACK grounding
cable to
negative (-) battery terminal with remaining hex bolt and keps nut. Tighten
securely
__ositive
Terminal
:, egative
Guard
(Black)
DD
REPLACING
;-_;-_
.-- -_
";;
'"
:'
then from the fully charged battery.
RED cable last from both batteries.
Weak or Dead Battery
Hex Bolt
!
Keps Nut
JUMPER
CABLES one end of the RED cable
TO REMOVE CABLES, REVERSE
ORDER 1. BLACK cable first from chassis
Close terminal access doors.
Close hood.
TO REMOVE
SEMBLY
HOOD
AND GRILL
1.
Raise hood.
2.
3.
Unsnap headlight wire connector.
Stand in front of tractor. Grasp hood at
sides, tilt toward engine and lift off of
tractor.
When replacing hood, be sure to reconnect the headlight wire connector.
4.
_\
/_\
Headlight Wire
Connector
27
AS-
ENGINE
IMPORTANT:
Damage to the needle
valve and the seat in carburetor
may result
if screw is turned in too tight.
Maintenance,
repair, or replacement of the
emission control devices and systems, which
are being done at the customers expense,
may be performed by any non-road engine
repair establishment or individual. Warranty
repairs must be performed by an authorized
engine manufacturer's
service outlet.
TO ADJUST THROTTLE
CONTROL
CABLE
PRELIMINARY
1.
2.
(
section
1.
2.
3.
of the manual.)
Start engine and allow to warm for five
minutes.
Make final adjustments
with
engine running and shift/motion
control
lever in neutral (N) position.
Move throttle control lever to slow position. With finger, rotate and hold throttle
lever against idle speed screw. Turn
idle speed screw to attain 1750 RPM.
While still holding throttle lever against
idle speed screw, turn idle mixture
valve full travel clockwise then counterclockwise
until engine runs rough.
Turn valve to a point midway between
those two positions.
Release throttle
lever.
Governor Control Plate
/
ACCELERATION
4.
"A"
Clamp Screw
TO ADJUST
CARBURETOR
-
FINAL SETTING
-(See "TO ADJUST
THROTTLE
CONTROL
CABLE" in this
The throttle control has been preset at the
factory and adjustment
should not be necessary. Check adjustment
as described
below before loosening cable. If adjustment is necessary,
proceed as follows:
1. With engine not running, move throttle
control lever from slow to choke position. Slowly move lever from choke to
fast position.
2. Check that holes "A" in governor
control lever and hole in governor plate
line-up. If holes "A" are not aligned,
loosen clamp screw and move throttle
cable until holes are aligned. Tighten
clamp screw securely.
Governor Control Lever
SETTING
Air cleaner assembly must be assembled to the carburetor when making
carburetor
adjustments.
Be sure the throttle control cable is
adjusted properly (see above).
Move throttle
TEST control
lever from slow
to fast position.
If engine hesitates or
dies, turn idle mixture valve out (counterclockwise)
1/8 turn. Repeat test and
continue to adjust, if necessary, until
engine accelerates
smoothly.
High speed stop is factory adjusted.
Do
not adjust or damage may result.
IMPORTANT:
Never tamper with the
engine governor, which is factory set
for proper engine speed. Overspeeding the engine above the factory high
speed setting can be dangerous.
If you
think the engine-governed
high speed
needs adjusting, contact a Sears or other
qualified service center, which has proper
equipment
and experience
to make any
necessary
adjustments.
Cable
NOTE: The carburetor on this engine is
low emission.
It is equipped with an idle
fuel adjusting needle with a limiter cap,
which allows some adjustment
within the
limits allowed by the cap. Do not attempt
to remove the limiter cap. The limiter cap
cannot be removed without breaking the
adjusting needle.
The carburetor
has been preset at the
factory and adjustment
should not be
necessary.
However, minor adjustment
may be required to compensate
for differences in fuel, temperature,
altitude or load.
If the carburetor does need adjustment,
proceed as follows:
In general, turning idle mixture valve in
(clockwise)
decreases
the supply of fuel to
the engine giving a leaner fuel/air mixture. Turning the idle mixture valve out
(counterclockwise)
increases the supply
of fuel to the engine giving a richer fuel/air
mixture.
Idle Speed _Screw _
Throttle
C
Idle Mixture
Valve with /
Limiter
z_
28
Immediatelyprepareyour tractor for storage at the end of the season or if the tractor will not be usedfor 30 days or more.
_CAUTION: Neverstore the tractor
with gasoline in the tank inside a building
where fumes may reach an open flame
or spark. Allow the engineto cool before
storing in any enclosure.
hose, or tank during storage. Also, alcohol
blended fuels (called gasohol or using
ethanol or methanol)
can attract moisture
which leads to separation
and formation of
acids during storage. Acidic gas can damage the fuel system of an engine while in
storage.
• Empty the fuel tank by starting the engine and letting it run until the fuel lines
and carburetor are empty.
• Never use engine or carburetor
cleaner
products in the fuel tank or permanent
damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable
alternative
in minimizing
the formation of
fuel gum deposits during storage.
Add
stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio
found on stabilizer container.
Run engine
at least 10 minutes after adding stabilizer
to allow the stabilizer to reach the car-
TRACTOR
Remove mower from tractor for winter
storage. When mower is to be stored for a
period of time, clean it thoroughly,
remove
all dirt, grease, leaves, etc. Store in a
clean, dry area.
1. Clean entire tractor (See "CLEANING"
in the Maintenance
section of this
2.
3.
4.
5.
manual).
Inspect and replace belts, if necessary
(See belt replacement
instructions
in
the Service and Adjustments
section of
this manual).
Lubricate as shown in the Maintenance
section of this manual.
Be sure that all nuts, bolts and screws
are securely fastened.
Inspect moving
parts for damage, breakage and wear.
Replace if necessary.
Touch up all rusted or chipped paint
surfaces; sand lightly before painting.
buretor. Do not empty the gas tank and
carburetor
if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace
with clean engine oil. (See "ENGINE" in
the Maintenance
section of this manual).
CYLINDER(S)
1.
2.
BATTERY
• Fully charge the battery for storage.
• After a period of time in storage, battery
may require recharging.
• To help prevent corrosion and power
leakage during long periods of storage,
battery cables should be disconnected
and battery cleaned thoroughly
(see
"TO CLEAN BATTERY AND TERMINALS" in the Maintenance
section of
3.
4.
Remove spark plug(s).
Pour one ounce of oil through spark
plug hole(s)into
cylinder(s).
Turn ignition key to "START" position
for a few seconds to distribute oil.
Replace
with new spark
plug(s).
OTHER
• Do not store gasoline
to another.
from one season
• Replace your gasoline can if your can
starts to rust. Rust and/or dirt in your
gasoline will cause problems.
• If possible, store your tractor indoors
and cover it to give protection from dust
and dirt.
this manual).
• After cleaning, leave cables disconnected and place cables where they
cannot come in contact with battery
terminals.
• Cover your tractor with a suitable protective cover that does not retain mois-
• If battery is removed from tractor for
storage, do not store battery directly on
concrete or damp surfaces.
ture. Do not use plastic. Plastic cannot
breathe which allows condensation
to
ENGINE
form and will cause your tractor to rust.
IMPORTANT:
Never cover tractor while
FUEL SYSTEM
engine
IMPORTANT:
It is important to prevent
gum deposits from forming in essential
fuel system parts such as carburetor, fuel
29
and exhaust
areas are still warm.
TROUBLESHOOTING
CHART:
See appropriate section in manual unless directed to Sears service center
PROBLEM
CAUSE
Will not start
1.
2.
Hard to start
CORRECTION
1.
2.
3.
Out of fuel.
Engine not "CHOKED"
properly.
Engine flooded.
4.
5.
6.
7.
Bad spark plug.
Dirty air filter.
Dirty fuel filter.
Water in fuel.
4.
5.
6.
7.
8.
9.
Loose or damaged wiring.
Carburetor
out of adjustment.
8.
9.
10. Engine valves out of
adjustment.
10.
1.
2.
3.
4.
5.
Dirty air filter.
Bad spark plug.
Weak or dead battery.
Dirty fuel filter.
Stale or dirty fuel.
1.
2.
3.
4.
5.
6.
7.
Loose or damaged wiring.
Carburetor
out of adjustment.
8. Engine valves out of
adjustment.
Engine will not
turn over
1. Brake pedal not depressed.
2. Attachment clutch is engaged.
3. Weak or dead battery.
4. Blown fuse.
5.
6.
7.
8.
Corroded battery terminals.
Loose or damaged wiring.
Faulty ignition switch.
Faulty solenoid or starter.
9. Faulty operator presence
switch(es).
Engine clicks
will not start
Loss of power
but
3.
1.
2.
3.
4.
qualified
qualified
center.
service
center.
1.
2.
3.
4.
5.
6.
7.
8.
Depress brake pedal.
Disengage attachment clutch.
Recharge or replace battery.
Replace fuse.
Clean battery terminals.
Check all wiring.
Check/replace
ignition switch.
Check/replace
solenoid or
starter.
9. Contact a Sears or other
qualified
1.
2.
3.
4.
Cutting too much grass/too
fast.
2. Throttle in "CHOKE" position.
3. Build-up of grass, leaves and
trash under mower.
4. Dirty air filter.
5. Low oil level/dirty oil.
1.
30
service
Clean/replace
air filter.
Replace spark plug.
Recharge or replace battery.
Replace fuel filter.
Empty fuel tank and refill tank
with fresh, clean gasoline.
6. Check all wiring.
7. See "To Adjust Carburetor"
in
Service and Adjustments
section.
8. Contact a Sears or other
Weak or dead battery.
Corroded battery terminals.
Loose or damaged wiring.
Faulty solenoid or starter.
1.
Fill fuel tank.
See "TO START ENGINE" in
Operation section.
Wait several minutes before
attempting
to start.
Replace spark plug.
Clean/replace
air filter.
Replace fuel filter.
Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter.
Check all wiring.
See "To Adjust Carburetor"
in Service and Adjustments
section.
Contact a Sears or other
service
center.
Recharge or replace battery.
Clean battery terminals.
Check all wiring.
Check/replace
solenoid or
starter.
Raise cutting height/reduce
speed.
2. Adjust throttle control.
3. Clean underside of mower
4.
5.
housing.
Clean/replace
air filter.
Check oil level/change
oil.
TROUBLESHOOTING
CHART:
See appropriate section in manual unless directed to Sears service center
PROBLEM
Loss of power
(cont.)
CAUSE
CORRECTION
6. Faulty spark plug.
6.
7. Dirty fuel filter.
8. Stale or dirty fuel.
7.
8.
9. Water in fuel.
9.
10. Spark
plug wire loose.
10.
Dirty engine air screen/fins.
Dirty/clogged
muffler.
Loose or damaged wiring.
Carburetor
out of adjustment.
11.
12.
13.
14.
11.
12.
13.
14.
15. Engine valves
adjustment.
Excessive
vibration
1. Worn,
15.
out of
bent or loose blade.
Clean and regap or change
spark plug.
Replace fuel filter.
Empty fuel tank and refill tank
with fresh, clean gasoline.
Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter.
Connect and tighten spark
plug wire.
Clean engine air screen/fins.
Clean/replace
muffler.
Check all wiring.
See "To Adjust Carburetor"
in Service and Adjustments
section.
Contact a Sears or other
qualified service center.
1.
Replace blade. Tighten blade
bolt.
2. Contact a Sears or other
qualified service center.
3. Tighten loose part(s).
Replace damaged parts.
2.
Bent blade mandrel.
3.
Loose/damaged
Engine dies when
tractor is shifted
into reverse
1.
Reverse operation system
(ROS) is not "ON" while
mower or other attachment
is engaged.
.
Turn ignition key to
ROS "ON" position.
See Operation section.
Engine continues
to run when
operator leaves
seat with
attachment
clutch engaged
1.
Faulty operator-safety
presence
control system.
.
Check wiring, switches and
connections.
If not corrected,
contact a Sears or other
qualified service center.
Poor cut - uneven
.
2.
3.
4.
5.
Worn,
part(s).
bent or loose blade.
Mower deck not level.
Buildup of grass, leaves,
trash under mower.
Bent blade mandrel.
and
Clogged mower deck vent
from build-up of grass, leaves,
and trash around mandrels.
31
1.
Replace blade. Tighten blade
bolt.
2. Level mower deck.
3. Clean underside of mower
housing.
4. Contact a Sears or other
qualified service center.
5. Clean around mandrels to
open vent holes.
TROUBLESHOOTING
CHART:
See appropriate section in manual unless directed to Sears service center
PROBLEM
Mower blades will
not rotate
Poor grass
discharge
CAUSE
CORRECTION
1.
Obstruction
in clutch
mechanism•
2. Worn/damaged
mower drive
belt.
3. Frozen idler pulley•
4. Frozen blade mandrel•
1.
Remove
obstruction.
2.
Replace
mower drive belt.
3.
4.
Replace idler pulley.
Contact a Sears or other
qualified service center.
1.
1.
Place throttle control in
"FAST" position.
Shift to slower speed.
Allow grass to dry before
mowing.
Level mower deck.
Check tires for proper air
pressure.
Replace/sharpen
blade.
Tighten blade bolt.
Clean underside of mower
housing.
Replace mower drive belt.
Reinstall blades sharp edge
down.
Replace with blades listed in
this manual.
Clean around mandrels to
open vent holes.
Engine
speed
2. Travel speed
3. Wet grass.
too slow.
too fast.
2.
3.
4.
5.
Mower deck not level.
Low/uneven
tire air pressure.
4.
5.
6.
Worn,
6.
bent or loose blade.
Buildup of grass, leaves and
trash under mower.
8. Mower drive belt worn.
9. Blades improperly
installed.
7.
10. Improper
10.
7.
blades
used.
8.
9.
11 •Clogged
mower deck vent
holes from buildup of grass,
leaves, and trash around
mandrels.
11.
Headlight(s)
not
working
(if so equipped)
1.
2.
3.
4.
5.
Light switch is "OFF".
Bulb(s) or lamp(s) burned out.
Faulty light switch.
Loose or damaged wiring.
Blown fuse.
1. Turn light switch "ON".
2. Replace bulb(s) or lamp(s).
3. Check/replace
light switch.
4. Check wiring and connections.
5. Replace fuse.
Battery willnot
charge
1.
2.
3.
Bad battery cell(s).
Poor cable connections.
Faulty regulator
(if so equipped).
Faulty alternator.
1.
2.
3.
Replace battery.
Check/clean
al/connections.
Replace regulator.
4.
Replace
1.
2.
Place freewheel
control in
"engaged"
position.
Replace motion drive belt.
3.
Purge transmission.
4.
Loss of drive
Engine "backfires'
when turning
engine "OFF"
1.
Freewheel control in
"disengaged"
position.
2. Motion drive belt worn,
damaged,
or broken.
3. Air trapped in transmission
during shipment or servicing.
•
Engine throttle control not se
between half and full speed
(fast) position before stoppin(
engine.
32
•
alternator.
Move throttle control
between half and full speed
(fast) position before
stopping engine.
TRACTOR
- - MODEL NUMBER 917.275820
SCHEMATIC
SOLENOID
STARTER
b
(OPT]ONAN
b
WHITE
CLUTCH
B_ACK
i_
/ BRAK_E
_
BI_CK
BLACK
GRAY
REVERSE
r
SWITCH
=
SHORTING CONNECTOR
I
BLACK
....
IGNITION
UNIT
%s
......
b
P_2RKPp_UGo
ON TWIN CYL. ENGINES)
.....
I
_[
BLUE
g HO_HOUR
FUEL I
_LININ_II
LINE
Ii
[F_
(OPTIONAL)
CHARGING
OUTPUT
3AMP
DC @SYSTEM
3600 RPM
oEoFU_'_L_%iOFF_,J A
'
r_
I
/
c
UGHT SWITCN
/
/
IGNITION SWITCH
POSITION CIRCUIT
OFF
RUN/OVERRIDE
RUN
START
"MAKE"
M+G+A1
B+A1
B+A1
B+S+A1
L+A2
I
LIGHTING
I
5AMP
.....
SYST EM O U_<_t
AC @ 3600
.......
-
RPM
_.
_.
DIODE
_"14_VOLTS
EQUIPPED WITH A SPECIAL
ALTERNATOR
SYSTEM.
THE LIGHTS ARE NOT
CONNECTED TO THE
BATTERY, BUT HAVE THEIR
OWN ELECTRICAL SOURCE.
BECAUSE OF THIS, THE
BRIGHTNESS OF THE LIGHTS
WILL CHANGE WITH ENGINE
SPEED. AT IDLE THE LIGHTS
WILL DIM. AS THE ENGINE IS
SPEEDED UP, THE LIGHTS
WILL BECOME THEIR BRIGHTEST.
02836
33
28 VOLTS AC MIN. @ 3600 RPM
(CH,ARGING SYSTEM DISCONNECTED)
,,,/
...
J_-j_
I
..............................
_
_
ALTERNATOR
, _-_,-_,J_J................................
'•
AC MIN.
@ S600 RPMTLIGHTS
OFF F
f
_
NON-REMOVABLE
CONNECTIONS
7
(_
REMOVABLE
CONNECTIONS
WIRING INSULATED CLIPS
NOTE: IF WIRING INSULATED CLIPS
WERE REMOVED FOR SERVICING OF
UNIT, THEY SHOULD BE REPLACED
TO PROPERLY SECURE YOUR WIRING.
TRACTOR
- - MODEL NUMBER 917.275820
ELECTRICAL
90
41
!..............
\
I
I
i
I
I
I
25
_6
_
\
\
16
'
//
!
/
I
I
!
!
\
i
i
_
\1
29
I
i
34
1
i !
\\
!
TRACTOR
- - MODEL NUMBER 917.275820
ELECTRICAL
KEY PART
NO. NO.
DESCRIPTION
1
2
8
16
163465
74760412
186491
176138
Battery
Bolt, Hex 1/4-20
Box, Battery
Switch Interlock
21
22
24
25
26
183759
4152J
4799J
146148
175158
Harness, Light Socket
Light Bulb
Cable, Battery
Cable, Battery
Fuse
27
28
29
30
33
34
40
41
42
43
73510400
145491
192749
193350
140403
110712X
193374
71110408
131563
178861
Nut Keps Hex 1/4-20 unc
Cable, Ground
Switch, Seat
Switch, Ignition
Key, Molded
Switch Light
Harness, Ignition
Bolt BIk Fin Hex 1/4-20 uric x 1/2
Cover, Terminal
Solenoid
45
52
55
90
121433X
141940
17490508
180449
Ammeter
Rectangular
Protection Wire Loop
Screw 5/16-18 x 1/2
Cover Terminal
91
92
93
94
190270
193465
192540
191834
Strap Battery Mount Front
Harness Pigtail Reverse
Screw
Module Reverse ROS
x 3/4
(wi4152J)
(Hour Meter)
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
35
TRACTOR
- - MODEL
CHASSIS AND ENCLOSURES
NUMBER
917.275820
259
260
258
273
_275
278
39
58
11_
208
209
278
208
/
20T
209
6O
2_
208
74
2O6
209
chassis-Laser-It.stir
36
46
TRACTOR
- - MODEL
CHASSIS AND ENCLOSURES
NUMBER
917,275820
KEY
PART
NO.
NO.
DESCRIPTION
1
2
5
9
10
11
13
14
17
18
26
28
174619
176554
155272
193511X013
STD533710
174996
172105X010
17490608
184272X615
184921
STD541437
184259
30
31
37
38
39
58
192393X615
139976
17490508
175710
174714
184270
Chassis
Drawbar
Bumper Hood/Dash
Dash
Bolt, Carriage
3/8-16 x 1
Panel, Dash, LH
Panel, Dash, RH
Screw Thdrol 3/8-16 x 1/2
Hood Assembly
Bumper Extrusion
Locknut, Hex, with insert 3/8-16 unc
Grille/Lens
Asm.
(includes
Key Nos. 258, 259, 260, 263, 264, 274 and 275)
Fender/Footrest
Bracket, Fender/Support
Screw, Thdrol. 5/16-18 x 1/2 TYT
Bracket Asm Pivot Mower Rear
Bracket Pivot Laser Lt
Air Duct
60
64
74
90
142
72140606
154798
STD541437
124346X
175702
Bolt Rdhd Sqnk 3/8-16 uric x 3/4
Dash Lower STLT
Nut Crownlock 3/8-16 unc
Nut 1/4
Plate Reinforcement
STLT
143
144
145
186689
175582
156524
Bracket Swaybar Chassis
Bracket Footrest STLT
Rod Pivot Chassis/Hood
159
166
206
207
208
209
217
258
259
260
263
264
272
273
274
275
155123X428
189747
170165
17670508
17670608
17000612
179132X428
184264X599
184263X599
184262X428
184265
184266
184269X428
184268X428
184260X428
184261X428
Cupholder
Screw Hi-Lo #13-16 x 5/8 w/Patch
Bolt Shoulder 5/16-18TT
ScrewThdrol
5/16-18 x 1/2
ScrewThdrol
3/8-16 x 1/2
Screw Hex Wsh Thdrol 3/8-16 x 3/4
Console Fuel Window
Lens RH
Lens LH
Cover Lens
Bezel Grille LH
Bezel Grille RH
Vent Hood RH
Vent Hood LH
insert Grille LH
insert Grille RH
278
-- -
191611
5479J
187801
Screw 10 x 3/4 Single Lead Hex
Plug Button
Plug Dome Plastic (Choke Hole)
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
37
TRACTOR
- - MODEL
NUMBER
917.275820
GROUND DRIVE
116
247
I
21
/
32
82 165 156
166
_-8
35
/3o
_39
4T'_
62
12011 _
36
52
36 35
95
30
29
/
i
252
55
19
25
78
/76
74
75
drive-hydro,stlt
38
53
TRACTOR
- - MODEL
NUMBER
917.275820
GROUND DRIVE
KEY
NO.
PART
NO.
DESCRIPTION
KEY
NO.
PART
NO.
8
10
14
15
16
19
21
22
24
25
27
192502
STD561210
10040400
74490544
STD541431
STD541437
130564
178141
73350600
106888X
STD561210
Transaxle Peerless LTH2000
Breakdown)
Rod Shift Fender Adjust
Pin Cotter 1/8 x 1 CAD
Washer Lock Hvy Helical
Bolt Hex FLGHD 5116-18 Gr.
Nut Lock Hex W/Ins. 5116-18
Nut Lock Hex W/Wsh 3/8-16
Knob 1/2-13
Rod, Brake
Nut, Hex Jam 318-16 Unc
Spring, Brake Rod
Pin Cotter 1/8 x 3/4 CAD.
69
70
74
75
76
77
78
81
82
83
85
89
95
142432
134683
137057
121749X
STD581075
123583X
121748X
178139
165711
19171216
150360
192387X428
178134
28
29
30
32
34
35
36
37
38
39
175765
71673
169592
74760512
175578
120183X
19211616
1572H
179114
72110622
Rod, Parking Brake
Cap, Parking Brake
Bracket, Transaxle
Bolt Hex Hd 5/16-18 unc x 3/4
Shaft, Foot Pedal
Bearing, Nylon
Washer
Pin, Roll
Pulley, Composite
Bolt Rdhd 3/8-16 unc x 2-3/4 Gr. 5
112
116
120
150
151
156
158
159
161
162
19091210
72140608
73900600
175456
19133210
166002
165589
183900
72140406
73680400
41
47
48
49
50
51
175556
127783
154407
123205X
72110612
STD541437
Keeper, Belt Idler
Pulley, Idler, V-Groove
Bellcrank, Clutch
Retainer, Belt
Bolt Carr Sh 3/8-16 x 1-1/2 Gr 5
Nut Crownlock
3/8-16 unc
163
165
166
168
169
197
74780416
165623
17490510
165492
165580
169613
52
53
55
56
57
59
61
62
63
64
65
66
STD541431
105710X
105709X
17060620
178138
169691
17120614
8883R
175410
173937
STD551143
154778
Nut, Crownlock
5/16-18 unc
Link, Clutch
Spring, Return, Clutch
Screw 3t8-16 x 1-1/4
V-Belt
Keeper, Center Span
Screw 3/8-16 x .875
Cover, Pedal
Pulley, Engine
Bolt Hex 7/16-20 x 4 Gr. 5
Washer
Keeper Belt Engine Hydro
198
202
212
245
246
247
250
251
252
263
169593
72110614
145212
178122
178121
181462
17060612
17060516
19131616
17000612
1
(See
5
unc
unc
DESCRIPTION
Screw Hex Wsh Hi-Lo 1/4-1/2 unc
Keeper Belt Engine
Spacer
Washer
25/32 x 1-1/4 x 16 Ga.
E-Ring
Key, Square
Washer
25/32 x 1-5/8 x 16 Ga.
Shaft Asm Cross Tapered
Spring Torsion
Washer
17/32 x 3/4 x 16 Ga.
Nut Lock Center 1/4-28 FNTHD
Console, Shift
Disconnect
Asm Rod Bypas LTH
Washer 9/32 x 3/4 x 10 Ga.
Bolt Rdhd Sqneck
3/8-16 x 1
Nut Lock Fig 3/8-16
Spacer Retainer
Washer
13/32 x 2 x 10 Ga.
Washer Srrted 5/16 ID x 1.125
Bracket Shift Mount
Hub Shift
Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr. 5
Nut Crownlock
1/4-20 unc
Bolt Hex Fin 1/4-20 unc x 1 Gr. 5
Bracket Pivot Lever
Screw 5/16-18 x 5/8
Bolt Shoulder 5/16-18 x .561
Plate Fastening
Nyliner
Snap-in 5/8"1D
Washer Nyl 7/8 ID x .105" Hyd
Bolt Carr Sh 3/8-16 x 1-3/4 Gr.5
Nut Hex Flange Lock
Strap Torque Lh LTH2000
Strap Torque Rh LTH2000
Link Shift Transaxle LTH2000
Screw 3/8-16 x .75
Screw 5/16-18 x 1
Washer 13/32 x 1 x 16 Ga.
Screw Hex Wsh Thdr 3/8-16 x 3/4
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
39
STEERING
TRACTOR
ASSEMBLY
- - MODEL
NUMBER
917.275820
_/
_+_=TJ---
34
/j::_39
...........
/
-L
67
68
67
88
4
13
65
L
8
29
6
43
82
4O
/
/
/
/
15
1515_
/
.............
10
steering
pl.lt
57
40
(
/
f
\\
\
95
TRACTOR
STEERING ASSEMBLY
- - MODEL
KEY
NO.
PART
NO.
1
2
3
4
5
6
8
10
11
13
15
17
26
28
29
30
32
34
36
37
38
39
40
41
42
43
44
46
65
67
68
71
82
87
88
91
95
97
186093X428
184706
169840
169839
6266H
121748X
12000029
175121
STD551137
136518
145212
190753
126847X
19131416
17000612
76020412
192757
10040500
155099
152927
186095X428
19113812
73540600
186737
145054X428
121749X
190752
184946X505
160367
72110618
169827
175146
169835
173966
175118
175553
188967
74780564
NUMBER
917.275820
DESCRIPTION
Steering Wheel
Front Axle Assembly
Spindle Assembly,
L.H.
Spindle Assembly,
R.H.
Bearing, Race, Thrust, Hardened
Washer 25/32 x 1-5/8 x 16 Ga.
Ring, Klip
Link, Drag
Washer, Lock
Spacer, Bearing, Front Axle
Nut, Hexflange Lock
Shaft Assembly,
Steering
Bushing Link Drag
Washer 13/32 x 7/8 x 16 Ga.
Screw 3/8-16 x 3/4
Pin Cotter 1/8 x 3/4
Rod, Tie
Washer Lock Hvy HIcl Spr. 5/16
Bushing, Steering
Screw TT #10-32 x 5 x 3/8 Flange
Insert, Steering Wheel
Washer 11/32 ID x 2-3/80D
x 12 Ga.
Lock Nut Center 3/8-24
Adaptor, Steering Wheel
Boot, Steering
Washer 25/32 x 1-1/4 x 16 Ga.
Extension Steering
Cap, Spindle
Spacer Brace Axle
Bolt Rhnd Sq 3/8-16
Brace Axle
x 2-1/4
Steering Asm
Bracket Susp Chassis Front
Washer Flat .781 x 1-1/2 x .14
Bolt Shoulder 7/16-20
Clip Steering
Washer Hardened
.793 x 1.637 x .060
Bolt 5/16-18 x 4" Gr. 5
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
41
TRACTOR - - MODEL NUMBER 917,275820
ENGINE
2
72
62
1
81
i
32
14
78_
31
39
33
23
29
OPTIONAL
EQUIPMENT
Spark Arrester
engine-bs.lcyl
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
170545
17720408
Control Throttle/Choke
Screw Hex Thd Cut 1/4-20
4
13
14
23
29
31
32
33
34
37
137352
165291
148456
169837
137180
157103
161696
123487X
106082X
137040
x 5/8
Engine (See Breakdown)
Briggs
Model No. 31P777-0296-E1
Muffler Exhaust
Gasket Muffler
Tube, Drain Oil Easy
Shield Browning/Debris
Arrestor Spark
Tank Fuel
Guard
Cap Fuel
Clamp Hose BIk
Pad Spacer
Line Fuel
42
30
KEY
PART
NO.
NO.
DESCRIPTION
38
39
44
181654
109227X
17670412
45
17000612
46
62
72
19091416
10010500
71070512
78
17060620
Plug, Drain Oil Easy
Pad Idler 1.75 x .75 x .06
Screw Hexwsh Thdrl 1/4-20 x
314
Screw Hex Wsh Thdrol
3/8-16 x 3/4
Washer 9/32 x 7/8 x 16 Ga.
Washer Split
Screw Hex Head Cap
5116-18 x 3/4
Screw 318-16 x 1-114
81
73510400
Nut, Keps
NOTE:
inches
All component
dimensions
1 inch = 25.4 mm
1/4-20
Starter
Nut
given in U.S.
TRACTOR
- - MODEL
NUMBER
917.275820
SEAT ASSEMBLY
10
5
17
seat
It.knob
12
1
KEY
PART
NO.
NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
188719
140551
71110616
19131610
145006
STD541437
124181X
17000616
19131614
182493
166369
174648
Seat
Bracket Pnt Pivot Seat
Bolt Fin Hex 3/8-16 unc x 1
Washer 13/32 x 3/4 x 10 Ga.
Clip Push In Hinged
Nut Hex Lock w/Ins 3/8-16 unc
Spring Seat Cprsn 2 250 BIk Zi
Screw 3t8-16 x 1.5 SMGML
Washer 13/32 x 1 x 14 Ga.
Pan Pnt Seat
Knob Seat
Bracket
Pnt Mounting
KEY
NO.
PART
NO.
DESCRIPTION
13
14
15
16
17
21
22
24
25
121248X
72050412
134300
121250X
123976X
171852
STD541431
19171912
127018X
Bushing Snap BIk Nyl 50 Id
Bolt Rdhd Sht Nk 1/4-20 x 1-1/2
Spacer Split 28 x 96 Zinc
Spring Cprsn 1 27 BIk Pnt
Nut Lock 1/4 Lge Fig Gr. 5 Zinc
Bolt Shoulder 5/16-18 unc-2A
Nut Hex Lock w/Ins 5/16-18
Washer 17/32 x 1-3/16 x 12 Ga.
Bolt Shoulder 5/16-18 x .62
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
Switch
43
TRACTOR - - MODEL NUMBER 917.275820
DECALS
1
7
16
3
\
2
11
2
22
19
14
14
5
15--
20
KEY
NO.
PART
NO.
1
2
3
5
6
7
8
9
11
14
15
156439
186367
186366
189020
133644
193565
179128
186572
193307
189088
160396
WHEELS
2 _
KEY PART
NO. NO.
DESCRIPTION
16
19
2O
22
Decal
Decal
Decal
Fender Danger Sears
Hood Side RH/LH
Hood RH/LH
Decal
Decal
Engine H/P
Maint Customer
Decal
Decal
Decal
Replacement
Deck
Fender Craftsman
Decal
Decal
Decal
Fender STLTH Oper Inst E/S
Dash Panel
Mower Drive Schematic
Sears
Dom
-
164065
138047
172331
149516
178392
138311
184310X428
184311X428
195509
195510
KEY PART
NO. NO.
&TIRES
5,8
4,10
1
2
3
4
59192
65139
106222X
59904
5
6
7
106732X624
278H
9040H
8
9
10
106108X624
138468
7152J
11
104757X428
144334
7
11
6 -,---._
wheeb
DESCRIPTION
Decal
Decal
Decal
Steering
Battery Diehard Sears
Deck Mower EZ3
Decal Battery
Decal Disconnect
Decal Lift Handle
Pad Footrest Lh
Pad Footrest Rh
Manual Owner's
Manual Owner's
STLT
STLT
(English)
(Spanish)
DESCRIPTION
Valve Cap, Tire
Stem, Valve
Tire, Front
Tube, Front Tire (Not Provided,
Service Item Only)
Rim, Front
Fitting, Grease (Front Wheel Only)
Bearing, Flange (Front Wheel
Only)
Rim, Rear
Tire, Rear
Tube, Rear Tire(Not Provided,
Service Item Only)
Cap, Axle
Sealant, Tire (10 oz. Tube)
1
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
44
TRACTOR
- - MODEL
NUMBER
917.275820
LIFT ASSEMBLY
7
13
13
19
\
1718
20
16
?
15
13
31
32"
-..
lift-rh=l piece 3
KEY
PART
KEY
PART
NO.
NO.
DESCRIPTION
NO.
NO.
DESCRIPTION
1
2
3
159460
159471
105767X
Lift Lever Inner Wire Asm.
Shaft Asm. Lift
Pin Groove
15
16
17
173288
73350800
175689
4
5
12000002
19211621
E Ring
Washer
18
19
73800800
139868
6
7
8
11
12
13
120183X
125631X
122365X
139865
139866
STD624008
Bearing Nylong
Grip Handle Fluted
Button Plunger Read
Link Asm Lift L.H.
Link Asm Lift R.H.
Retainer Spring
20
31
32
163552
169865
73540600
Link Front
Nut Jam Hex 1/2-13 unc
Trunnion
Nut Lock w/Wsh
1/2-13 unc
Arm Suspension
Mower
Retainer Spring
Bearing, Pvt. Lift. Tapered
Nut Crownlock 3/8-24
21132 x 1 x21
Ga.
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
45
TRACTOR
- - MODEL
NUMBER
917,275820
MOWER DECK
3
52 55\
'
142
il 47
21
23
113 111
24
25
_2
26
119
28
27
29
5
6
12
f
19
21
117
42
D man-t-path
stlt 3
_116
46
TRACTOR
- - MODEL
NUMBER
917.275820
MOWER DECK
KEY
NO.
PART
NO.
DESCRIPTION
KEY
NO.
PART
NO.
1
2
165892
STD533107
Mower
Bolt
56
59
165723
141043
3
4
5
6
8
9
10
138017
165460
STD624008
178024
850857
STD551137
140296
11
138971
- -
134149
- -
139775
67
68
92
111
112
113
116
117
118
119
129
130
131
134
135
149846
144959
STD541437
179292
179293
17000512
4898H
188606
73930600
19121414
19131312
STD523710
STD533710
156941
159765
13
137645
14
15
16
18
19
20
21
23
24
25
26
27
28
29
30
31
32
33
34
36
40
44
45
46
48
52
53
54
55
128774
110485X
174493
72140505
132827
159770
STD541431
177563
105304X
123713X
110452X
130968X428
19111016
131491
173984
187690
153535
178342
72110612
131494
73900600
140088
STD624003
137729
133944
139888
184907
178515
155046
Bracket Asm,Sway
Bar, Front
Bracket Sway Bar 38/42"
Retainer Spring
Bar Sway Deck
Bolt, Hex 3/8-24 x 1.25 Gr. 8
Washer, Lock
Washer, Hardened
(The following blades are available)
Blade, 42" Hi-Lift
(For bagging or discharge)
Blade, 42" Mulching Std
(For mulching mowers only)
Blade, 42" Mulching Premium
(For better wear when mulching)
Shaft Assembly,
Mandrel, Vented
(Incl. Key Number 6)
Housing, Mandrel, Vented
Bearing, Ball, Mandrel
Stripper, Mower Deck
Bolt, Carriage 5/16-18 x 5/8
Bolt, Shoulder
Baffle, Vortex
Nut, Crownlock
5/16-18 unc
Bracket, Deflector
Cap, Sleeve
Spring, Torsion, Deflector
Nut, Push
Shield, Deflector
Washer 11/32 x 5/8 x 16 Ga.
Rod, Hinge
ScrewThdrol
Rolling Wsh Hd
Washer, Spacer
Pulley, Mandrel
Nut, Toplock, Flanged
Bolt Carr Sh. 3/8-16 x 1-1/2 Gr. 5
Pulley, idler, Flat
Nut, Lock Fig. 3/8-16 uric
Guard, Mandrel,
L.H.
Retainer
Screw, Thd. Roll 114-20 x 5t8
Washer, Hardened
Bolt, Shoulder 5/16-18 unc
Arm Assembly,
Pad, Brake
Washer, Hardened
Arm, idler
136
138
155986
159763
139
159767
Bracket Asm. Wheel
Front RH
Gauge
140
159768
Bracket Asm. Wheel
Front LH
Gauge
142
143
144
145
146
147
148
149
150
152
158
159
184
185
--
165890
157109
158634
165888
171977
131335
169022
165898
19091210
169676
17720408
STD533717
19131410
188234
130794
Arm Spring Brake Mower
Bracket Arm Idler 42"
--
169583
Housing
DESCRIPTION
Spacer, Retainer
Guard, Tuv Idler (94)
Knob Custom Oval
V-Belt
Locknut, Hex W/Wsh 3/8-16 uric
Bracket Wheel Guage LH
Bracket Wheel Guage RH
Screw 5116-18 x 3/4
Bolt, Shoulder
Wheel, Gauge
Nut, Crownlock
3/8-1
Washer
13132 x 7/8 x 14 Ga.
Washer
13/32 x 13/16 x 12 Ga.
Bolt, Fin Hex 3/8-16 uncx 1Gr. 5
Bolt Rdhd Sqnk 318-16 unc x 1
Pin Head Rivet
Bracket Asm. Wheel Gauge
Rear LH
Bar Adj. Gauge Wheel
Bracket Asm. Wheel Gauge
Rear RH
Keeper Belt 42" Clutch Cable
Pulley idler Flat
Bolt Carraige idler
Spring Extension
Spring Return idler
Retainer Spring Yellow Zinc
Washer
9t32 x 314 x 10 Ga.
Cable Clutch 42"
Screw Hex Thd Cut 114-20 x 518
Bolt Rdhd Sqn 3/8-16 unc x 1-3/4
Washer 3/8
Head Asm Cable Clutch
Mandrel Assembly
(Includes
housing, shaft and shaft hardware
only-pulley
not included)
Replacement
Mower, Complete
(Std. Deck-Order
separately
guage wheel components
key
nos. 116- 119).
NOTE: All component dimensions given in U.S.inches
1 inch = 25.4 mm
47
TRACTOR
- - MODEL NUMBER 917.275820
PEERLESS TRANSAXLE - - MODEL NUMBER LTH2000
1
_,
150
115
"_
_
106
.(_)-_},_
v
31 29
_-
_
157
_
5
_
_'_1113 :_
(_
32
87
_ 15
__.,m
_
49
_
56
_-_
_
,_
(_(_
6
67
_=
_u_
106
31
_
_
114
9
87
.
• 3
__
-191
19o
ii_
203
_2o4A
'_
_ 208
zo4
'
185
200
25
184--_
/
/
/
22
//
/
l__e
100
[
ii
.....
48
lo2/_\
lo2lol
TRACTOR
- - MODEL NUMBER 917.275820
PEERLESS TRANSAXLE - - MODEL NUMBER LTH2000
KEY
NO.
PART
NO.
DESCRIPTION
KEY
NO.
PART
NO.
DESCRIPTION
1
3
5
6
9
13
14
15
17
22
23
772151
770135
776355
778263
786197
778368
778368
778373
786139
792194
792195
Cover L.H.
Case
Counter Shaft
Spur Gear 11T
Neutral Sleeve (.572)
Bevel Gear (Incl. 14) (13 Teeth)
Bevel Gear (Incl. 13) (13 Teeth)
Ring Gear (54 Teeth)
Drive Pin
Spring
Washer .750 ID
70
79
85
87
99
100
101
102
103
104
105
786196
792201
792154
788088A
792141
792200
792199
792184
792193
792198
780096
Spacer .625.765
Spring
Oil Fill Plug
Oil Seal 3/4"
Washer .3771D .058W
Snubber Washer
Snubber Spring .471D
Washer .4371D .078W
Screw, 1/4-28 x .490
Nut, 3/8-24
Washer .625 ID .057W
25
26
28
29
31
36
37
38
40
41
42
42A
43
44A
44B
45
792073A
792125
792035
780065
780189
790071
790007
799021
792204
790102
792202
792203
792171
790100
790099
790101
Screw 1/4-20 x 1-1/4"
Retaining Ring
Retaining Ring
Washer .627 ID .091W
Washer .563 ID .062W
Brake Disk
Brake Pad Plate
Brake Pad
Roll Pin .25
Brake Lever
Screw, 1/4-20 x 3/4
Screw, 1/4-20 x 1-3/4
Screw, 10-24 x .500
Inside Brake (Mach)
Outside Brake (Casting)
Actuator Rod
106
107
109
113
114
115
127
150
157
180
182
183
184
185
190
191
786162
792046
788104
786199
786200
786198
784384
788093A
788102
730229
788103
792118
792196
798050
792150
792151
Sleeve Assembly
Screw, 1/4-20 x 1"
"O" Ring
Sleeve Ass'y (Incl. 157)
Sleeve Ass'y (Incl. 87)
Sleeve Assembly
(Incl. 87)
Shift Lever Ass'y (Incl. 109)
Liquid Gasket RTV Silicon
Oil Seal 9/16"1D
BOil Spec. (80W90)
Grommet
Relief Valve
Hose Barb
Tubing 1/2 x 5
Washer
Nut 7/16-20
47
48
49
56
65
67
774869
774688
778378
778379
780195
776440
Axle 16.812
Axle 11.625
Spur Gear 18T
Spur Gear 81T
Washer .7501D .062W
Brakeshaft
200
794787
203
206
207
208
209
210
798044
798055
798053
798040
798054
794788
Differential
(Gear Reduction
Drive)
Pulley & Hub Ass'y
Disconnect
Lever
Mounting Plate
Fan
Control Lever
Hydro Module LH Fender Control
49
TRACTOR
- - MODEL NUMBER 917.275820
BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0296-E1
5_
691 @
718 dp
43,_
684I'11_
16,
584_
30 i
9_
307_
1264 I_
1263<_
358 ENGINE GASKET SET
3@
}_'
24
868_)
12
943
146e_
0
741
1022
1270
20@ 6170
__
51 _}
524 _
I
691(_
842 O
1019 LABEL KIT
I
1058 OWNER'S
1266
759
0
I
MANUAL
I
11036EMISSION
LABELI
I
I
48SHORT
BLOCK I I@1
I
1330REPAIR
MANUAL
] EE]--I
1329 REPLACEMENT
ENGINE
15g
I
7506
200
89
1027
50
TRACTOR
- - MODEL NUMBER 917.275820
BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0296-E1
1095 VALVE GASKET
SET
1022
238
868
1022
6170
103 z
525
1022
914
334
366,<_
121 CARBURETOR
93'_
95t_
104
d¢2
105
_
106[_l17_b
OVERHAUL
634A @_ )
967@
137_) R
276@
63@
1266
142_
6170
1266A
1266A
127 O
KIT
977 CARBURETOR
()
_
>
GASKET
SET
276 @
1127_
137_
276@
51
947
TRACTOR
- - MODEL NUMBER 917.275820
BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0296-E1
305A
1265
643
1267
1040
968
305' _
729
1070
801
697
74
_"
73_
_
544_
803_
1005
_
1044_
310_
1051&
579
_
_ _1_
4621 797 "_---_
5o_
802
52
TRACTOR
- - MODEL NUMBER 917.275820
BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0296-E1
KEY
NO.
PART
NO.
KEY
NO.
PART
NO.
1
2
3
4
5
7
9
11
12
697174
399265
391086
697188
698147
699168
697109
697113
697110
108A
117
118
121
125
127
130
131
133
692344
694352
697228
697241
698445
695005
691750
494379
494381
13
15
16
20
22
23
24
25
--
690360
690946
697127
690947
692125
693557
222698
699052
699054
Screw (Cylinder Head)
Plug-Oil Drain
Crankshaft
,Seal-Oil
(PTO Side)
Screw (Crankcase
Cover/Sump)
Flywheel
Key-Flywheel
Piston Assembly
(Standard)
Piston Assembly
(.020" Oversize)
Ring Set (Standard)
Ring Set (.020" Oversize)
Lock-Piston
Pin
Pin-Piston
137
141
141A
142
146
186
187
187A
188
192
202
209
216
222
281165
495097
495931
697140
691639
692317
697098
698417
691693
691986
691841
692208
691840
694042
OSGasket-Float
Bowl
Kit-Choke Shaft (Manual Choke)
Kit-Choke Shaft (Choke A Matic)
ONozzle-Carburetor
Key-Timing
Connector-Hose
Line-Fuel
Line-Fuel
Screw (Control Bracket)
Adjuster-Rocker
Arm
Link-Mechanical
Governor
Spring-Governor
Link-Choke
Bracket-Control
26
-27
28
699051
697559
698469
697099
29
--
697126
697263
692852
695760
695761
691279
691279
697108
690964
691968
690564
698492
Rod-Connecting
(Standard)
Rod-Connecting
(.020" Undersize)
Screw (Connecting
Rod)
Valve-Exhaust
Valve-intake
Spring-Valve
(Intake)
Spring-Valve
(Exhaust)
Guard-Flywheel
Retainer-Valve
Slinger-Governor/Oil
Tappet-Valve
Camshaft
227
232
238
240
265
267
276
304
305
305A
306
307
309
691374
691842
691843
298090
691024
695134
692255
699829
697102
697103
697107
691003
693551
Lever-Governor
Control
Spring-Governor
Cap-Valve
Filter-Fuel
Clamp-Casing
Screw (Casing Clamp)
OSWasher-Sealing
Housing-Blower
Screw (Blower Housing)
Screw (Blower Housing)
Shield-Cylinder
Screw (Cylinder Shield)
Motor-Starter
32
33
34
35
36
37
40
43
45
46
48
50
697762
690193
Short Block
Manifold-intake
310
311
690323
497608
Bolt (Starter
Brush Set
51
53
54
73
74
78
89
93
94
95
98
104
105
106
108
692137
690227
691148
697133
697897
691003
690283
690602
498030
691636
495800
690525
231855
691780
690464
333
334
337
358
363
383
385
385A
492341
691061
691043
697191
19203
89838
694476
690297
Armature-Magneto
Screw (Magneto Armature)
Plug-Spark
Gasket Set-Engine
Flywheel Puller
Wrench-Spark
Plug
Screw (Fuel Pump)
Screw (Fuel Pump)
DESCRIPTION
Cylinder Assembly
Kit-Bushing/Seal
(Magneto
,Seal-Oil
(Magneto Side)
Sump-Engine
Head-Cylinder
.+Gasket-Cylinder
Head
• Gasket-Breather
Tube-Breather
,Gasket-Crankcase
Side)
.O$+Gasket-lntake
Stud (Carburetor)
Screw (intake Manifold)
Screen-Rotating
Screw (Rotating Screen)
Screw (Flywheel Guard)
Plug-Oil
OBushing-Throttle
Shaft
Kit-Idle Mixture
Screw (Throttle Valve)
Kit-Idle Speed
O Pin-Float Hinge
OValve-Float
Needle
OSeat-lnlet
Valve-Choke
(Manual Choke)
O
$
+
Included
Included
121
Included
Included
DESCRIPTION
Valve-Choke
(Choke A Matic)
O Jet-Main (Standard)
Jet-Main (High Altitude)
Kit-Carburetor
Overhaul
Carburetor
Plug-Welch
Valve-Throttle
Kit-Throttle
Shaft
Float-Carburetor
in Engine Gasket Set, Key. No. 358
in Carburetor
Overhaul
Kit, Key. No.
in Carburetor
Gasket Set, Key. No. 977
in Valve Gasket Set, Key. No. 1095
NOTE: All component
1 inch = 25.4 mm
53
Motor)
dimensions
given in U.S. inches
TRACTOR
- - MODEL NUMBER 917.275820
BRIGGS & STRATTON ENGINE-MODEL NUMBER 31P777, TYPE NUMBER 0296-E1
KEY
NO.
PART
NO.
DESCRIPTION
387
404
431
697090
691691
697122
Pump-Fuel
Washer (Governor
Elbow-Intake
445
462
474
503
505
510
513
523
524
525
544
552
562
579
584
601
614
616
697153
691261
696459
691532
691251
693699
692024
697086
691032
697085
692034
697144
691119
691029
697112
95162
691620
692012
Filter-Air Cleaner Cartridge
Washer (Starter Cable)
Alternator
Strap-Starter
Nut (Governor Control Lever)
Drive-Starter
Clutch-Drive
Dipstick
,Seal-Dipstick
Tube
Tube-Dipstick
Starter-Armature
Bushing-Governor
Crank
Bolt (Governor Control Lever)
Nut (Starter Cable)
Cover-Breather
Passage
Clamp-Hose
Pin-Cotter
Crank-Governor
617
634
692138
690801
634A
690802
635
643
654
684
691
697
718
729
741
750
757
758
759
783
789
797
801
802
803
830
842
847
851
868
914
918
943
691909
697155
690958
697157
692407
690372
690959
691224
697128
691033
697607
697134
697392
693713
698329
693167
691283
691286
693757
691095
691031
697087
692424
690968
690960
697091
690589
O ,SeaI-O Ring (Intake Manifold)
OSpring/Seal
Assembly
(Manual
Choke)
OSpring/Seal
Assembly
(Choke A
Matic)
Boot-Spark
Plug
Retainer-Air
Filter
Nut (Carburetor)
Screw (Breather Passage Cover)
,Seal-Governor
Shaft
Screw (Drive Cap)
Pin-Locating
Clip-Wire
Gear-Timing
Screw (Oil Pump Cover)
Link-Counterweight
Counterweight
Pin-Counterweight
Gear-Pinion
Harness-Wiring
Nut (Brush Retainer)
Cap-Drive
Cap-End
Housing-Starter
Stud (Rocker Arm)
,SeaI-O Ring (Dipstick Tube)
Dipstick/Tube
Assembly
Terminal-Spark
Plug
,+Seal-Valve
Screw (Rocker Cover)
Line-Vacuum
,SeaI-O Ring (Oil Pump Cover)
Crank)
KEY
NO.
PART
NO.
DESCRIPTION
947
965
967
694393
499613
697015
Solenoid-Fuel
Cover-Oil Pump
Filter-Pre Cleaner
968
975
977
987
1005
1017
1019
1022
1023
1024
1026
......
1027
1029
1034
1035
1036
1040
699848
495933
690192
691326
697111
690770
697143
272475
692492
499054
692003
692011
696854
691751
690822
693784
695700
699852
1044
1051
1058
1059
1070
1090
1091
1095
1119
1127
1263
1264
1265
1266
1266A
1267
1270
1279
1329
1330
698139
Screw (Flywheel)
691265
Ring-Retaining
275038
Owner's Manual
698516
Kit-Screw/Washer
691058
Screw (Flywheel
Fan)
691293
Retainer-Brush
691333
Cap-Limiter
690190
Gasket Set-Valve
691183
Screw (Alternator)
691657
Screw (Float Bowl)
697124
Reed-Breather
697104
Screw (Breather
Reed)
697125
Support-Blower
Housing
691917
,OSeaI-O
Ring (intake Elbow)
697123
OSeaI-O Ring(Intake
Elbow)
697424
Latch-Blower
Housing
697156
Plug-AVS
Counterweight
690960
Screw (Blower Housing Support)
31Q777-0036
Replacement
Engine
272147
Repair Manual
O
:l:
+
Included
Included
121
Included
Included
Cover-Air Cleaner
Bowl-Float
Gasket Set-Carbu retor
OSeaI-Throttle
Shaft
Fan-Flywheel
Screen-Oil
Pump
Kit-Label
,+Gasket-Rocker
Cover
Cover-Rocker
Arm
Pump-Oil
Rod-Push (Intake)
Rod-Push (Exhaust)
Filter-Oil
Arm-Rocker
Guide-Push
Rod
Shaft-Pump
Label-Emission
Plate-Trim
in Engine Gasket Set, Key. No. 358
in Carburetor
Overhaul
Kit, Key. No.
in Carburetor
Gasket Set, Key. No. 977
in Valve Gasket Set, Key. No. 1095
NOTE: All component
1 inch = 25.4 mm
54
dimensions
given in U.S. inches
SUGGESTED
GUIDE
FOR SIGHTING
SLOPES
ONLY RIDE UP AND DOWN
NOT ACROSS HILL
(_
O1
15 DEGREES
_
FOR SAFE
HILL,
MAX.
down the face of slopes, never across the face. Do not mow
ARNING:
To avoid
serious
your tractorto up
and
slopes
greater
than 15
degrees.injury,
Makeoperate
turns gradually
prevent
tipping or loss of control. Exercise extreme caution when
changing
direction
on slopes.
1. Fotd this page atong dotted tine indicated
above.
2. Hold page before you so that its left edge is vertica!iy parattet to a tree
trunk or other upright
structure,
3. Sight across
the fotd in the direction
of hill elope you want to measure.
4. Compare
the angie of the fotd with the s_ope of the hiit.
OPERATION
Your Home
For repair - in your home - of all major brand appliances,
iiiiiiiiii
'_
lawn and garden equipment,
or heating and cooling systems,
iiiiiiiiii
iiiiiiiiii
no matter who made it, no matter who sold it!
iiiiiiiiii
iiiiiiiiii
For the replacement
parts, accessories
and
iiiiiiiiii
owner's
manuals
that
you
need
to
do-it-yourself.
iiiiiiiiii
iiiiiiiiii
iiiiiiiiii
For Sears professional
installation
of home appliances
iiiiiiiiii
and items like garage door openers and water heaters.
iiiiiiiiii
iiiiiiiiii
1-800-4-MY-HOME ® Anytime, day or night
iiiiiiiiii
iiiiiiiiii
(I-800-469-4663)
(U.S.A. and Canada)
iiiiiiiiii
www.sears.com
www.sears.ca
iiiiiiiiii
iiiiiiiiii
iiiiiiiiii
iiiiiiiiii
iiiiiiiiii
Our Home
iiiiiiiiii
iiiiiiiiii
iiiiiiiiii
For repair of carry-in products like vacuums,
lawn equipment,
iiiiiiiiii
iiiiiiiiii
and electronics,
call or go on-line for the nearest
!!!!!!!!!!_
Sears Parts and Repair Center.
iiiiiiiiii
iiiiiiiiii
1-800-488-1222
Anytime, day or night (U.S.A. only)
iiiiiiiiii
iiiiiiiiii
www.sears,
corn
iiiiiiiiii
iiiiiiiiii
iiiiiiiiii
iiiiiiiiii
iiiiiiiiii
To purchase a protection agreement (U.S.A.)
iiiiiiiiii
iiiiiiiiii
or maintenance agreement (Canada) on a product serviced by Sears:
iiiiiiiiii
iiiiiiiiii
1-800-827-6655
(U,S,A,)
1-800-361 °6665 (Canada)
iiiiiiiiii
iiiiiiiiii
iiiiiiiiii
iiiiiiiiii
iiiiiiiiii
Para pedir servicio de reparaci6n
Au Canada pour service en francois:
iiiiiiiiii
iiiiiiiiii
1-800-LE-FOYER
Mc
iiiiiiiiiiiiiiiiiii_'_ a domicilio, y para ordenar piezas:
iiiiiiiiiiiiiiiiiii¸¸
1.888-SU-HOGAR
(1-888-784-6427)
sM
(I-80G533-6937)
www,sears.ca
02410
© Sears, Roebuckand Co.
® Registered Trademark / TMTrademark / SMService Mark of Sears, Roebuck and Co.
® Marca Registrada / TMMarca de Fabrica / SMMarca de Servic[o de Sears, Roebuck and Co.
MCMarque de commerce / MOMarque depos6e de Sears, Roebuck and Co.
195509
11.19.04
TR
Printed
in U.S.A.
Download PDF

advertising