Instruction manual | Craftsman 917.375011 Lawn Mower User Manual

AUDIO VIDEO SURROUND RECEIVER
VRS-6100
INSTRUCTION MANUAL
KENWOOD CORPORATION
Quick Start Reference
Please read the following pages so that you can enjoy the surround sound at the best
condition.
(These pages give shortcut explanations on how to connect the speaker system to the
receiver, set up the speakers and play a source.)
"Let's play DVD video software"
^&
About the supplied remote control
Compared to standard remote controls, the remote control supplied with this receiver has
several operation modes. These modes enable the remote control to control other audio/
video components. In order to effectively use the remote control, it is important to read
the operating instructions and obtain a proper understanding of the remote control and
how to switch its operation modes (etc.).
Using the remote control without completely understanding its design and how to switch the
operation modes may result in incorrect operations.
For the U.S.A.
Register Online
Register your Kenwood Home Audio product
at www.kenwoodusa.com
Plus opt in to receive e-mail updates and other offers when you
register at our web site.
B60-5484-00 00 MA ( K, P )
*5484/01-07/EN
1
0403
04.5.17, 2:12 PM
Before applying power
Caution : Read this page carefully to ensure safe operation.
Units are designed for operation as follows.
U.S.A. and Canada ........................................... AC 120 V only
Safety precautions
WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED
TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC
SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO
THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE.
2 EN
*5484/01-07/EN
2
04.5.17, 8:34 AM
Before applying the power
How to use this manual
Unpacking
This manual is divided into four sections, Preparations, Operations,
Unpack the unit carefully and make sure that all the accessories
are present.
Remote Control, and Additional Information.
Preparations
Shows you how to connect your audio and video components to the
receiver and prepare the surround processor. Since this receiver works
FM indoor antenna (1)
AM loop antenna (1)
Remote control unit
(1)
Batteries (R6/AA)
(2)
with all your audio and video components, we will guide you in setting up
your system to be as easy as possible.
Operations
Shows you how to operate the various functions available on the
receiver.
Remote Control
Shows you how to operate other components using the remote control,
as well as a detailed explanation of all remote control operations. Once
you have setup the remote control, you’ll be able to operate both this
model and your KENWOOD DVD player using the remote control
supplied with this model.
Additional Information
Shows you additional information such as "In case of difficulty" (trouble
shooting) and "Specifications".
If any accessories are missing, or if the unit is damaged or fails
to operate, notify your dealer immediately. If the unit was
shipped to you directly, notify your shipper immediately. Kenwood
recommends that you retain the original carton and packing
materials in case you need to move or ship the unit in the future.
Keep this manual handy for future reference.
Maintenance of the unit
When the front panel or case becomes dirty, wipe with a soft, dry
cloth. Do not use thinner, benzine, alcohol, etc. for these agents may
cause discoloration.
In regard to contact cleaner
Do not use contact cleaners because it could cause a malfunction. Be
specially careful not to use contact cleaners containing oil, for they
may deform the plastic component.
3 EN
*5484/01-07/EN
3
04.5.17, 8:34 AM
Before applying the power
Special features
True home theater sound • ~ ª
This receiver incorporates a wide variety of surround modes to bring you
maximum enjoyment from your video software. Select a surround mode
according to your equipment or the software you are going to play and enjoy!
÷ Dolby Digital EX
÷ Dolby PRO LOGIC IIx, Dolby PRO LOGIC II
÷ Dolby Digital
÷ DTS-ES
÷ DTS NEO:6
÷ DTS
÷ DSP Mode
ACTIVE EQ £
ACTIVE EQ mode will produce a more dynamic sound quality in any
condition. You can enjoy a more impressive sound effect when ACTIVE
EQ is turned on during Dolby Digital and DTS playback.
Remote control ›
In addition to the basic receiver, the remote control supplied with this
receiver can also operate KENWOOD DVD player. Just follow the simple
setup procedure.
4 EN
*5484/01-07/EN
4
04.5.17, 8:34 AM
Before applying the power
Contents
Caution : Read the pages marked
carefully to ensure safe operation.
Before applying power ........................................... 2
Safety precautions ............................................... 2
How to use this manual ............................................. 3
Unpacking .................................................................. 3
Special features ......................................................... 4
Contents .................................................................... 5
Names and functions of parts ...................................... 6
Main unit .................................................................... 6
Remote control unit ................................................... 7
Remote
Control
Basic remote control operations for other
components .......................................... 34
DVD player operation keys ........... 34
Additional
Information
In case of difficulty................................ 35
Specifications ........................................ 37
Setting up the system ............................ 8
Connecting a DVD player ............... 9
Connecting video components, audio
components ................................. 10
Digital connections ....................... 11
Connecting the speakers ............. 12
Connecting the speaker terminals ... 13
PRE OUT connections .................. 14
Preparations
Connecting to the FRONT AUX jacks ... 14
Connecting the antennas ............. 15
Preparing the remote control ....... 15
Let’s play DVD video software
......................................................... 16
Preparing for playback ......................... 18
Speaker settings .......................... 18
Operations
Normal playback ................................... 22
Listening to a source component ... 22
Adjusting the sound ..................... 23
Recording .............................................. 25
Analog sources .............................. 25
Digital sources ............................... 25
Listening to radio broadcasts .............. 26
Tuning radio stations .................... 26
Presetting radio stations .............. 26
Receiving preset stations ............. 27
Receiving preset stations in order
(P.CALL) ........................................ 27
Ambience effects .................................. 28
Surround modes ........................... 28
Surround play ............................... 30
Convenient functions ........................... 32
5 EN
*5484/01-07/EN
5
04.5.17, 8:34 AM
Names and functions of parts
Main unit
Input mode indicators
CLIP indicator
ACTIVE EQ indicator,
MUTE indicator
Speaker selection indicators,
Input channel indicators (The Input
channel indicators lights up to indicate
the channels contained in the input
signal. The "S" indicator lights when the
surround component consists of a single
channel.)
1
^ %
96 kHz fs indicator
Listen mode indicators
Frequency display,
Input display,
Preset channel display,
Listen mode display
AUTO indicator, ST. indicator,
TUNED indicator, TONE indicator
Display
2 34 5 6
7
8
9
View when the FRONT AUX jack cover is open.
1 POWER ON/STANDBY
key *
Use to turn the power ON/STANDBY.
6 BAND key
Lights when the power is in the standby
mode.
2 DIMMER key
∞
Use to select the REC MODE.
Use to adjust the brightness of the display.
‹
8
3 INPUT MODE key
Use to switch between the full auto, digital and
analog input.
4 SOUND key
•
Use to adjust the sound quality and the ambience effects.
5 MEMORY key
§
§
! VOLUME CONTROL knob
§
º
@ INPUT SELECTOR key
# SETUP key
™
º
% FRONT AUX jacks
^ PHONES jack
Lights when the receiver is in the DTS mode.
£
™
&
Use to select the speakers' settings etc.
$ LISTEN MODE key
LOUDNESS indicator
#
Use to select input sources.
Lights when the receiver is in the Dolby
Digital mode.
DTS indicator
@
Use to adjust the receiver volume.
Use to select the auto or manual tuning
mode.
8 Dolby D indicator
!
$
Use to select the broadcast band.
7 AUTO/MONO key
STANDBY indicator
0
º
Use to select the listening mode.
$
¢
Use for headphone listening.
Lights when the LOUDNESS mode is ON.
9 MULTI CONTROL button
&
Use to control a variety of settings.
0 ACTIVE EQ key
£
Use to select ACTIVE EQ’s setting.
Use to presetting of radio stations.
Standby mode
While the standby indicator is lit, a small amount of power is supplied to the system to back up the memory. This is called standby mode. Under the
condition, the system can be turned ON by the remote control unit.
6 EN
*5484/01-07/EN
6
04.5.17, 8:34 AM
Names and functions of parts
Remote control unit
POWER
1
2
3
4
5
6
DVD/POWER
7
8
9
RECEIVER
0
+10
LOUDNESS DISC SKIP
SOUND LISTEN MODE INPUT MODE
SETUP
MENU ON SCREEN RETURN TOP MENU
MULTI CONTROL
BAND
ENTER
TUNING
AUTO
DIMMER
TUNER
VIDEO
P.CALL
AUX
DVD
BASS BOOST ACTIVE EQ
F.AUX
TONE
If the name of a function is different on the
receiver and on the remote control, the name of
the remote control key in this manual is indicated
in parentheses.
DISC SEL.
VOLUME
MUTE
1 Numeric keys
¶›
If CD or MD is selected as the input source,
these keys function as numeric keys. If tuner
is selected as the input source, these keys
are used to call up station presents.
2 LOUDNESS key
£
Use to switch the status of LOUDNESS.
3 SETUP key
*
Use to select the speakers’ settings etc.
›
MENU key
•
Use to adjust the sound quality and the ambience effects.
ON SCREEN key
£
! MUTE key
¢
Use to temporarily mute the sound.
# DVD/POWER key
›
Use to operate the DVD component.
*¤
Use to return to the operation of this model.
If CD is selected as the input source, this key
functions as the multi-CD player disc skip key.
^ INPUT MODE key
Use to operate other components.
§
If CD is selected as the input source, this keys
function as the play/pause key.
If MD or TAPE is selected as the input source,
this key functions as the play key.
Use to select the REC MODE.
∞
Use to adjust the brightness of the display.
*
key
Use to turn the receiver ON/STANDBY.
% DISC SKIP key
8
‹
8 key
Use to operate other components.
¡ AUTO key
7 key
If CD, MD or TAPE is selected as the input
source, this key functions as the stop key.
™ TONE key
DISC SEL. key
1/¡ keys
TOP MENU key
›
£ VOLUME keys
If CD, MD or TAPE is selected as the input
source, these keys function as search key.
Use to operate the DVD component.
If tuner is selected as the input source, these
keys function as preset channel call keys.
4/¢ keys
& LISTEN MODE key
£
Use to switch the status of TONE control.
Use to switch between the full auto, digital and
analog input.
¶
§
Use to select the auto or manual tuning mode.
Use to tuning of radio broadcasting.
7 P.CALL keys
§
Use to select the broadcast band.
) DIMMER key
Use to select ACTIVE EQ setting.
*
Use to control a variety of settings as well as in
tuning of radio broadcasting.
6 TUNING keys
0 ACTIVE EQ key
$ RECEIVER key
Use to operate the DVD component.
5 MULTI CONTROL (%/fi) keys
£
Use to select the maximum adjustment setting for the low frequency range.
›
( BAND key
3/8 key
Use to select input sources.
9 BASS BOOST key
@ POWER
Use to operate the DVD component.
4 SOUND key
8 Input Selector keys (TUNER, DVD,
VIDEO, AUX, F. AUX)
™
›
Use to operate the DVD component.
™
Use to adjust the receiver volume.
º
Use to select the listening mode.
RETURN key
›
Use to operate the DVD component.
* ENTER key
If CD or MD is selected as the input source,
these keys function as skip keys.
Use to operate other components.
7 EN
*5484/01-07/EN
7
04.5.17, 8:34 AM
Setting up the system
Input mode settings
CAUTION
Make sure that the power cord plug is disconnected from the AC wall
outlet before proceeding to connections. Also be sure to disconnect the
power cord plug from the AC wall outlet before changing connections.
For the connections of other system components, see pages 9 to 15.
When connecting an associated system component, be sure to read
its instruction manual.
DVD, VIDEO and FRONT AUX inputs each include jacks for digital
audio input and analog audio input.
The initial factory settings for audio signal playback for DVD, VIDEO
and FRONT AUX are full auto.
After completing connections and turning on the receiver,follow the
steps below.
INPUT SELECTOR
Microcomputer malfunction
If operation is not possible or an erroneous display appears, even
though all connections have been made properly, reset the micro
computer referring to "In case of difficulty".
fi
INPUT MODE
Notes
1. Be sure to turn off the system components before connecting them.
2. Be sure to insert every connection cable completely into the jack.
Incomplete connection may result in absence of audio output or
production of noise.
3. Be sure to disconnect the power cord from the AC wall outlet before
inserting or removing a connection cable.
4. Installation of outdoor antenna is a dangerous work. Please have your
dealer or a specialized technician install it.
INPUT
MODE
Input Selector keys
5. Select the speaker installation locations with care. If a speaker is
installed near a source of magnetism including a magnet, the mutual
interference with the speaker may produce color irregularities on the
TV screen.
1 Use the INPUT SELECTOR key (or Input Selector keys)
to select DVD, VIDEO or FRONT AUX.
Analog audio connections
Audio connections are made using RCA pin cords. These cables transfer
stereo audio signal in an "analog" form. This means the audio signal
corresponds to the actual audio of two channels. These cables usually
have 2 plugs on each end,one red for the right channel and one white for
the left channel.
These cables are to be prepared separately by the user.
CAUTION
Each press switches the setting as follows:
1 "F-AUTO": Auto detect
("AUTO DETECT" indicator lights up)
2 "D-MANUAL": Fixed to digital input
("DIGITAL" indicator lights up)
3 "ANALOG": Fixed to analog input *
*
Be sure to adhere to the following, or proper ventilation will be
blocked causing damage or fire hazard.
÷ Do not place any objects impairing heat radiation onto the top of
the unit.
÷ Leave some space around the unit (from the largest outside
dimension including projection) equal to or greater than, shown
below.
Top panel
Side panel
2 Press the INPUT MODE key.
: 10 cm
: 10 cm
Back panel
: 10 cm
÷ Do not use the appliance on a bed, sofa, rug or similar surface.
Otherwise, absorption of dust may cause a fire hazard.
("AUTO DETECT", "DIGITAL" indicator goes off)
Can not be selected for DTS playback.
Auto detect:
In "F-AUTO (FULL AUTO)" mode ("AUTO DETECT" indicator light
up), the receiver detects the digital or analog input signals
automatically. The receiver will select the input mode and listening mode automatically during playback to match the type of input
signal (Dolby Digital, PCM, DTS) and the speaker setting. º
The "DIGITAL" indicator lights up when a digital signal is detected.
The "DIGITAL" indicator is extinguished when no digital signal is
detected.
Fixed to digital input:
Select this mode if you want to keep the decoding condition
(Dolby Digital, DTS, PCM, etc.) in the current listen mode.
When "D-MANUAL (DIGITAL MANUAL)" mode is selected, the
set listen modes may be changed automatically depending on the
listen mode. º
Fixed to analog input:
Select this setting to play analog signals from a VCR, etc.
If the INPUT MODE key is pressed quickly, sound may not be
produced. Press the INPUT MODE key again.
8 EN
*5484/08-15/EN
8
04.5.17, 8:34 AM
Setting up the system
Connecting a DVD player
If you have connected a DVD player to the receiver with digital connection, be sure to read the "Input mode settings" section carefully.
8
L
To AC wall
outlet
OPT.
VIDEO
L
COAXIAL
DVD
R
DIGITAL IN
IN
AUX IN
VIDEO IN
DVD
MONITOR
AUDIO LINE
COMPOSITE
OUT or
MIX LINE OUT
(Audio cord)
VIDEO OUT
(Yellow RCA
pin cord)
DIGITAL OUT (AUDIO)
(Coaxial cord)
COMPOSITE
VIDEO IN
(Yellow RCA pin cord)
DVD player
Monitor TV
÷ Digital audio connections are required when playing multi-channel signals such as the Dolby Digital and DTS signals.
÷ To play the DVD player connected in this page, select the "DVD" input selector. ™
9 EN
*5484/08-15/EN
9
04.5.17, 8:34 AM
Setting up the system
Connecting video components, audio components
L
Audio components
R
AUDIO LINE OUT (Audio cord)
AUX IN
Monitor TV
VIDEO IN (Yellow RCA
pin cords)
MONITOR
REC OUT PLAY IN
VIDEO OUT
VIDEO IN
VIDEO
REC OUT PLAY IN
AUDIO
LINE IN
(Audio
cord)
AUDIO LINE
OUT
(Audio cord)
Video deck, Cassette
deck or MD recorder
VIDEO
IN
(Yellow
RCA pin
cords)
VIDEO OUT (Yellow RCA pin cords)
10 EN
*5484/08-15/EN
10
04.5.17, 8:34 AM
Setting up the system
Digital connections
The digital in jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable of outputting DTS, Dolby Digital, or standard
PCM (CD) format digital signals.
If you have connected a DVD player to the receiver with digital connection, be sure to read the "Input mode settings" section carefully.
8
DTS disclaimer clause
When playing DTS-encoded discs, excessive noise will be exhibited from the analog stereo outputs of the CD or DVD player. To enjoy DTS
Digital Surround™ playback, this unit must be connected to the digital output of the CD or DVD player.
L
R
OPT.
VIDEO
COAXIAL
DVD
DIGITAL IN
OPTICAL DIGITAL
OUT (AUDIO)
(Optical fiber cord)
CD player
Component with DTS,
Dolby Digital, or PCM
OPTICAL DIGITAL OUT
Connect the video signal and analog audio signals to the VIDEO jacks.
(See "Connecting video components, audio components". 0)
11 EN
*5484/08-15/EN
11
04.5.17, 8:34 AM
Setting up the system
Connecting the speakers
Whether each speaker is connected properly can be
confirmed by outputting the test tone and checking if
each speaker channel outputs audio. For details, see
"Speaker settings" (Step 5 Adjust the speaker volume
level). )
CAUTION
Make sure that the power cord plug is disconnected from the AC
wall outlet before proceeding to speaker cord connections.
If the conductor wires on the extremity of speaker cord are
untwisted, there is a risk of short-circuiting. Be sure to twist
them well before connecting the speaker cord.
Surround Speakers
Be sure to connect both surround speakers
Front Speakers
Center
Speaker
Left
Left
Right
SPEAKERS
R FRONT L
C
Right
(8-16Ω)
R SURR
L
L
R
12 EN
*5484/08-15/EN
12
04.5.17, 8:34 AM
Setting up the system
Connecting the speaker terminals
1 Strip coating.
3 Insert the cord.
Speaker placement
Subwoofer (SW)
Center speaker (C)
Twist
2 Push the lever.
4 Return the lever.
Front
speaker (L)
Surround
speaker (LS)
¶ Never short circuit the + and – speaker cords.
¶ If the left and right speakers are connected inversely or the
speaker cords are connected with reversed polarity, the sound
will be unnatural with ambiguous acoustic imaging. Be sure to
connect the speakers correctly.
Speaker impedance
After confirming the speaker impedance indications printed on the
rear panel of the receiver, connect speakers with matching impedance ratings. Using speakers with a rated impedance other than that
indicated on the rear panel of the receiver could result in malfunctions
or damage to the speakers or receiver.
Front
speaker (R)
Listening
position
Surround back
speaker (LB)
Surround
speaker (RS)
Surround back
speaker (RB)
Front speakers : Place the left and right speakers at each side of your TV.
Angle the speakers towards the listening area to enhance the stereo
effect.
Center speaker : Place front and center. This speaker stabilizes the
sound image and helps recreate sound motion. Required for surround
playback.
Surround speakers : Place the surround speakers as high as possible,
either directly to the sides of the listening area or else slightly behind
the listening area. Adjust the angles so that these speakers are facing
directly towards the listeners.
Subwoofer : Usually, place the subwoofer in the front center position in
the listening room, near one of the front speakers near the center
speaker. (Since the subwoofer has less directivity than other speakers,
it can be placed almost in any position that can offer the best low
frequency reproduction according to the room layout.)
Surround back speakers : Place the surround back speaker behind the
listening position, at the same height as the left and right surround
speakers.
¶ Although the ideal surround system consists of all the speakers listed
above, if you don't have a center speaker or a subwoofer, you can
divide those signals between the available speakers in the speaker
settings steps to obtain the best possible surround reproduction from
the speakers you have available. *
13 EN
*5484/08-15/EN
13
04.5.17, 8:34 AM
Setting up the system
PRE OUT connections
Connecting to the FRONT AUX jacks
The receiver has additional PRE OUT jacks.
Note that the output from the PRE OUT jacks needs to be connected
to an external power amplifier.
If you want to connect surround back speakers to these jacks, be always
sure to connect two surround back speakers for the left and right.
If you use a component that you do not usually connect to the receiver,
such as a portable video camera, connect it to the FRONT AUX jacks on
the front panel of the receiver. These jacks are particularly convenient
when dubbing audio/video from a portable video camera.
INPUT SELECTOR
L
R
L
R
SUB WOOFER
SURROUND BACK
PRE OUT
VIDEO
OUT
AUDIO
OUT
Surround Back speakers
R
L
Power amplifier
Subwoofer
Power amplifier
Powered subwoofer
Game Player
¶ Connecting a speaker cord directly to a PRE OUT jack will not
produce any sound from the speaker.
14 EN
*5484/08-15/EN
14
04.5.17, 8:34 AM
OPTICAL DIGITAL
OUT (AUDIO)
Setting up the system
Connecting the antennas
Preparing the remote control
AM loop antenna
The supplied loop antenna is for use indoors. Place it as far as possible
from the receiver, TV set, speaker cords and power cord, and adjust the
direction for best reception.
Loading the batteries
1 Remove the cover.
2 Insert the batteries.
AM antenna terminal connections
1 Push lever.
2 Insert cord.
3 Release lever.
3 Close the cover.
Attach to
the stand
2
1
¶ Insert two AA-size (R6) batteries as indicated by the polarAM loop antenna
ity markings.
Remote control operation
When the STANDBY indicator is lit, the power turns ON when you press
the POWER on the remote control. When the power comes ON, press
the key you want to operate.
ANTENNA
AM
GND
FM 75Ω
Operating other
component range
Remote sensor
FM outdoor antenna
POWER
Use an antenna adaptor
(Commercially available)
¶ When pressing more than one remote control key successively,
press the keys securely by leaving an interval of 1 second or more
FM indoor antenna
between keys.
FM indoor antenna
Notes
1. The supplied batteries may have shorter lives than ordinary batteries
The supplied indoor antenna is for temporary use only. For stable signal
reception we recommend using an outdoor antenna. Disconnect the
due to use during operation checks.
2. When the remote-controllable distance gets shorter than before,
indoor antenna when you connect one outdoors.
replace both batteries with new ones.
3. Placing the remote sensor in direct sunlight, or in direct light from a
high frequency fluorescent lamp may cause a malfunction.
FM antenna terminal connections
Insert cord.
In such a case, change the location of the system installation to
prevent malfunction.
FM outdoor antenna
Lead the 75Ω coaxial cable connected to the FM outdoor antenna into the
room and connect it to the FM 75Ω terminal.
15 EN
*5484/08-15/EN
15
04.5.17, 8:34 AM
Let’s play DVD video software
STEP 1 Connect the speakers and TV to the receiver.
For details, see "Setting up the system" 8 ~ $
CAUTION
Make sure that the power cord plug is disconnected from the AC wall outlet before proceeding to speaker cord connections.
If the conductor wires on the extremity of speaker cord are untwisted, there is a risk of short-circuiting. Be sure to twist them well before
connecting the speaker cord.
Connection of speakers:
A
B
C
Front speakers (L,R)
Center speaker
Subwoofer
D
Surround speakers (L,R)
E
Surround back speakers (L,R)
C
1~
L
1~
RECEIVER
B
SW
R
DVD
C
LS
RS
Listening position
A
D
LB
SPEAKERS
R FRPNT L
(8-16Ω)
ANTENNA
OPT.
R SURR
C
L
VIDEO
E
L
COAXIAL
DVD
AM
L
GND
FM 75Ω
R
DIGITAL IN
R
SUB WOOFER
SURROUND BACK REC OUT PLAY IN
IN
AUX IN
PRE OUT
VIDEO OUT
VIDEO IN VIDEO IN
VIDEO
3
DVD
MONITOR
1
21
Connection of TV monitor:
Connection of DVD player:
1
Composite video connection
2
Analog audio connection
3
Digital audio connection (Coaxial code)
1
Composite video connection
16 EN
*5484/16-27/EN
16
04.5.17, 8:34 AM
E
RB
C
A
B
D
E
Let’s play DVD video software
STEP 2 Set up the speakers.
POWER ON/STANDBY
INPUT SELECTOR
For details, see "Speaker settings" . * ~ ¡
1 Connect the power cord to the AC wall outlet and press
SETUP
MULTI CONTROL @ / #
2 Press
, press
to select "SP SETUP" and press
.
.
If you connect KENWOOD speaker system KS-2100HT, KS-708HT or KS-908HT:
Press
to select the model of the connected speaker system and press
.
"HTB 1": Speaker system KS-2100HT.
"HTB 2": Speaker system KS-708HT.
"HTB 3": Speaker system KS-908HT.
Model availability may differ depending on the country and sales area.
When "TEST TONE" is displayed, press
to select "EXIT" and then press
.
÷ When the speaker setting is set to "HTB 1", "HTB 2" or "HTB 3", the DOLBY PRO LOGIC IIx, DTS-ES and DOLBY DIGITAL EX listen modes cannot be selected.
÷ More detailed settings such as the volume level of each speaker and distance to each speaker are also available. ( ~ ¡
If you use another speaker system want a setup according to it:
Press
to select "CUSTOM" and press
Press
to select each of the speaker setup items.
to select the speaker setup item and press
.
SUBW ON: A subwoofer is connected.
SUBW
SUBW OFF: No speaker is connected.
Speaker size:
FRNT
LRG: Relatively large-size speakers.
NML: Normal-size speakers.
Speaker size:
CNTR, SURR, BS
LRG: Relatively large-size speakers.
NML: Normal-size speakers.
OFF: No speaker is connected.
Press
until "TEST TONE" is displayed, press
to select "EXIT" and then press
.
÷ When the speaker setting is set to "BS OFF", the DOLBY PRO LOGIC IIx, DTS-ES and DOLBY DIGITAL EX listen modes cannot be selected.
÷ More detailed settings such as the volume level of each speaker and distance to each speaker are also available. ( ~ ¡
STEP 3 Play a disc on the DVD player.
1 Press
to select "DVD".
2 Start playback of the DVD player.
For the operation, also refer to the instruction manual for your DVD player.
÷ You can select various listen modes to enjoy surround playback of various kinds of video software.
º
17 EN
*5484/16-27/EN
17
04.5.17, 8:34 AM
Preparing for playback
4 Select a speaker system.
Speaker settings
To enable you to obtain optimum enjoyment from the receiver’s listening
modes, make sure to complete the speaker settings (Subwoofer, Front,
Center, Surround and Surround Back speakers) as described below.
sP
MULTI CONTROL @/#
POWER ON/STANDBY
1 Select "SP SETUP" and press the SETUP key again so
that the speaker system indication "SP SYSTEM"
scrolls across the display.
sYsTEM
2 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to select the speaker system
setting.
SETUP
1 "HTB 1": Select "HTB 1" if you use speaker system KS-2100HT.
2 "HTB 2": Select "HTB 2" if you use speaker system KS-708HT.
3 "HTB 3": Select "HTB 3" if you use speaker system KS-908HT.
4 "CUSTOM": Select to set up the speakers according to
POWER
SETUP
the speaker system in use. (Speaker setup is required
every time after the speaker system is changed.)
÷ When the setting "HTB 1", "HTB 2" or "HTB 3" is selected, the
procedure skips to step 5.
÷ When you use a KENWOOD speaker system and select
"HTB 1", "HTB 2" or "HTB 3" set the speaker setup, the audio
will be corrected automatically according to the speaker
MULTI
CONTROL %/fi
1 Turn on the power to this receiver by pressing the POWER
ON/STANDBY
key (or POWER
characteristics.
÷ When the speaker setting is set to "HTB 1", "HTB 2", "HTB 3 " or
"BS OFF" the DOLBY PRO LOGIC IIx, DTS-ES and DOLBY
key).
DIGITAL EX listen modes cannot be selected.
2 If you want to use the remote control unit, press the RECEIVER
key on the remote to set it to the receiver control mode.
3 Initiate the setup mode.
÷ The subwoofer setting indication "SUBW" appears.
1 Press the SETUP key.
2 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) for the following displays.
1 "SP SETUP"
2 "TEST TONE"
3 "DISTANCE"
÷ While the main setup display is appeared, the setup mode
can be canceled by selecting "EXIT" and then pressing the
SETUP key.
Subwoofer
Front
Center
TEST TONE
AUTO
L
C
R
RS
RB
LB
LS
SW
0N
DISTANCE
MANUAL
L
Front Left
C
Center
R
Front Right
RS
Right Surround
RB
Surround Back Right
Surround
LB
Surround
Back
LS
1 "SUBW ON" :
When a subwoofer is connected.
2 "SUBW OFF" :
When no subwoofer is connected.
÷ The initial setting is "SUBW ON".
÷ When "SUBW OFF" is selected and the selection is
The flow of the SETUP is as follows;
HTB 1
HTB 2
HTB 3
Custom
sU B W
4 Use the MULTI CONTROL button (or the MULTI CONTROL %/fi keys) to select the appropriate subwoofer
setting.
4 "LFE LEVEL"
5 "EXIT"
SP SETUP
3 For general speaker setting, use the MULTI CONTROL
button (or the MULTI CONTROL %/fi keys) to select
"CUSTOM", and press the SETUP key again.
Surround Back Left
Left Surround
LFE LEVEL
EXIT
established by pressing SETUP key in step 5 below,
the front speakers are set automatically to "FRNT LRG"
and the procedure jumps to step 8.
5 Press the SETUP key to accept the setting.
÷ The front speakers setting indication "FRNT" appears.
FR N T
LRG
SW
Subwoofer
Re-mix
Continued to next page
18
EN
*5484/16-27/EN
18
04.5.17, 8:34 AM
Preparing for playback
6 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to select the appropriate
front speakers setting.
@ Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to select appropriate surround back speaker setting.
1 "FRNT LRG": Large front speakers are connected to
If you selected "SURR LRG" as the surround speaker setting :
1 "BS LRG":
Large surround back speaker is connected to the re-
the receiver.
2 "FRNT NML": Average size front speakers are connected to the receiver.
÷ When the subwoofer setting is "SUBW ON", front speakers setting is "FRNT LRG" and a stereo source is played,
the low frequencies may be reproduced through the
front speakers and no audio output from the subwoofer
in certain listen modes. In this case, set the subwoofer
re-mix setting in step $ to "REMIX ON" to output the
low frequencies from the subwoofer.
7 Press the SETUP key to accept the setting.
÷ The center speaker setting indication "CNTR" appears.
8 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to select the appropriate
center speaker setting.
If you selected "FRNT LRG" as the front speakers setting:
1 "CNTR LRG": A large center speaker is connected to
the receiver.
2 "CNTR NML": An average size center speaker is
connected to the receiver.
3 "CNTR OFF" :
When no center speaker is connected.
If you selected "FRNT NML" as the front speakers setting:
1 "CNTR NML": An average size center speaker is
connected to the receiver.
2 "CNTR OFF": When no center speaker is connected.
9 Press the SETUP key to accept the setting.
÷ The surround speaker setting indication "SURR" appears.
0 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to select the appropriate surround speaker setting.
If you have selected "CNTR LRG" as the center speaker setting:
1 "SURR LRG":
Large surround speakers are connected to the receiver.
2 "SURR NML":
Average size surround speakers are connected to the
ceiver.
2 "BS NML":
Average size surround back speaker is connected to the
receiver.
3 "BS OFF":
When no surround speakers are connected.
Bs
LRG
If you selected "SURR NML" as the surround speaker
setting :
1 "BS NML" :
Average size surround back speaker is connected to the
receiver.
2 "BS OFF" :
When no surround speakers are connected.
# Press the SETUP key to accept the setting.
÷ The subwoofer re-mix setting indication "REMIX" appears.
$ Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to select the appropriate
subwoofer re-mix setting.
If "REMIX ON" is selected as the subwoofer re-mix setting,
the low frequencies are enhanced by adding the low frequencies of other channels to the subwoofer channel or
adding the low frequencies of the subwoofer to other
channels depending on the speaker setup.
1 "REMIX ON": Subwoofer re-mix setting mode to the
receiver is ON.
2 "REMIX OFF": Subwoofer re-mix setting mode to the
receiver is OFF.
÷ If subwoofer is turned "SUBW OFF", subwoofer re-mix
setting is not visible.
% Press the SETUP key to accept the setting.
receiver.
3 "SURR OFF" :
When no surround speakers are connected.
If you have selected other than "CNTR LRG" as the center
speaker setting:
1 "SURR NML":
Average size surround speakers are connected to the
receiver.
2 "SURR OFF":
When no surround speakers are connected.
÷ When "SURR OFF" is selected and the selection is established by pressing SETUP in step ! below, the procedure
jumps to step $. However, if the subwoofer setting is
"SUBW OFF", you can complete the speaker setup and
proceed to the speaker volume level adjustment in step 5.
! Press the SETUP key to accept the setting.
÷ The surround back speaker setting indication "BS" appears.
19 EN
*5484/16-27/EN
19
04.5.17, 8:34 AM
Preparing for playback
5 Adjust the speaker volume level.
6 Input the distance to the speakers.
From your usual listening position, adjust the volume levels. The volume
levels from each speaker should be the same.
÷ In steps 5, indications appear only for the selected channels of the
speakers that require adjusting.
This setting allows the signals output from different speakers to reach
the listening position simultaneously.
÷ In steps 6, indications appear only for the selected channels of the
speakers that require adjusting.
1 Press the SETUP to begin TEST TONE.
2 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to select "AUTO" or "MANUAL".
1 "AUTO": Select this setting to adjust the speaker volume
levels using the test tone. The test tone will be output from
every speaker channel in automatic sequence.
2 "MANUAL": Select to select the speaker channel to
output the test tone using SETUP key.
Press the SETUP key again select either "AUTO" or
"MANUAL".
Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to adjust the volume level of
the test tone output from the speaker channel to
be adjusted.
For "AUTO" selection, the first test tone is heard from
the front left speaker for 2 seconds. The next test tone
is heard from the speakers in the following sequence
for 2 seconds each.
The channel indication blinks while the test tone is being output.
Measure the distance from the listening position to each
of the speakers.
Jot down the distance to each of the speakers.
Distance to Front speaker (L)
: ____ feet (meters)
Distance to Center speaker (C)
Distance to Front speaker (R)
: ____ feet (meters)
: ____ feet (meters)
Distance to Surround speaker (RS)
Distance to Surround back speaker (RB)
Distance to Surround back speaker (LB)
: ____ feet (meters)
: ____ feet (meters)
: ____ feet (meters)
Distance to Surround speaker (LS)
: ____ feet (meters)
1 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to select "DISTANCE" on
setup displays, and press the SETUP key.
2 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to adjust the distance to the
front speakers.
The speaker indicator to be adjusted blinks.
÷ The allowable setting range is 1 to 30 feet (0.3 to 9.0 m),
adjustable in 1 foot (0.3 m) increments.
1) F T
Indication in feet
L
)dB
÷ If you change the volume level settings for the speakers
while listening to music, the settings referred to on this
page are also changed. ¤
3 Press the SETUP key to accept the setting.
4 Repeat steps 2 and 3 to input the distance for each of
the speakers.
÷ The speaker setting values will return to the default
values when the speaker setting is set to OFF.
For "MANUAL" selection, press the SETUP key each
time to select the speaker channel, and use the MULTI
CONTROL button (or the MULTI CONTROL %/fi keys)
to adjust the volume level.
3 Press the SETUP key to accept the setting.
÷ The test tone is turned off. This model enters the mode
for inputting the distance to the speakers.
20 EN
*5484/16-27/EN
20
3)M
Indication in meters
04.5.17, 8:34 AM
Preparing for playback
7 Adjust the LFE LEVEL (Low Frequency Effects level)
Adjust the level of the low-frequency fields effect (LFE) signal, which is
the signal used exclusively for giving the field effect of bass tone, in the
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, the "CLIP" indicator
will blinks to indicate the source signal. Adjust the input level.
Dolby Digital or DTS signal.
1 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to select "LFE LEVEL" on
setup displays, and press the SETUP key.
2 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to adjust the LFE LEVEL.
1 Press the RECEIVER key on the remote control unit to set
it to the receiver control mode.
2 Press the SOUND key repeatedly until the "INPUT"
indication appears.
LF E
)dB
3 Use the MULTI CONTROL button (or the MULTI
CONTROL
%/fi keys) to adjust the input level.
÷ The LFE LEVEL is adjusted from 0dB to -10dB in 1dB
step decrements.
3 Press the SETUP key to accept the setting.
4 Setup is complete when the EXIT indication appears.
EX I T
IN P U T
)
÷ The adjustment mode is displayed for approximately 20
seconds.
÷ The input level may be adjusted to any one of three settings:
0dB, -3dB, and -6dB. (The initial setting is 0dB.)
÷ You can store a separate input level for each input selector.
5 Press the SETUP key to exit the SETUP mode.
21 EN
*5484/16-27/EN
21
04.5.17, 8:34 AM
Normal playback
Some preparatory steps are needed before starting playback.
Listening to a source component
POWER ON/STANDBY
INPUT SELECTOR
INPUT SELECTOR
INPUT MODE
VOLUME CONTROL
POWER
INPUT
MODE
Input selector keys
Input selector keys
VOLUME
Turning on the receiver
1 Turn on the power to the related components.
2 Turn on the power to this receiver by pressing the
POWER ON/STANDBY
1 Press
the INPUT SELECTOR key (or the Input selector
keys/ DVD, VIDEO, AUX, F.AUX, TUNER) to select the source
you want to listen to.
(or the POWER ).
1 Tuner (FM/AM broadcast reception)
2 "VIDEO"
3 "DVD"
4 "AUX"
Selecting the input mode
If you have selected a component connected to the COAXIAL DVD,
OPT. VIDEO or DIGITAL IN (OPTICAL) jacks, make sure that the input
mode setting is correct for the type of audio signal to be used. 8
5 "FRONT AUX"
2 Start playback from the selected source.
3 Use the VOLUME CONTROL knob (or the VOLUME +/- keys) to
adjust the volume.
22 EN
*5484/16-27/EN
22
04.5.17, 8:34 AM
Normal playback
Adjusting the sound
One-touch low frequency emphasis (Bass Boost)
ACTIVE EQ
(PCM stereo and analog stereo mode only)
You can adjust the sound quality when this model is in the PCM stereo
and analog stereo modes.
MULTI CONTROL @/#
PHONES
1 Press the RECEIVER key on the remote control unit to set
VOLUME CONTROL
it to the receiver control mode.
2 Press the BASS BOOST key.
÷ Press the key once to select the maximum (+10) low frequency emphasis setting.
÷ TONE mode will automatically be turned ON.
LOUDNESS
MULTI
CONTROL %/fi
ACTIVE EQ
BASS BOOST
÷ The BASS BOOST key is defeated during tone adjustment in
the SOUND mode (¤,‹) or when the listen mode is
switched to a mode other than the stereo mode.
TONE
MUTE
VOLUME
Switching back to the previous setting
Press the BASS BOOST key.
Adjusting the TONE (PCM stereo and analog stereo mode only)
Adjusting the LOUDNESS mode
(PCM stereo and analog stereo mode only)
1 Press the RECEIVER key on the remote control unit to set
You can adjust the Loudness function which controls the low volume
settings to maintain the music's richness.
it to the receiver control mode.
2 Press the TONE key to select the TONE mode.
3 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to select "TONE ON" or "TONE OFF"
Lights up
1 Press the RECEIVER key on the remote control unit to set
it to the receiver control mode.
2 Press the LOUDNESS key to turn the LOUDNESS setting
ON.
TO N E
ON
To cancel
Press the LOUDNESS key again.
4 When in "TONE ON" selection, press the TONE key for the
following displays.
1 "BASS" :
ACTIVE EQ mode
Select this to adjust the low frequency range.
2 "TREBLE" :
Select this to adjust the high frequency range.
You can enjoy a more impressive sound effect when ACTIVE EQ is
turned ON.
5 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to adjust the sound quality.
TR E B L E
1)
6 Repeat steps 4 and 5 as required.
÷ The bass and treble levels are adjustable from -10 to +10 in
2 step increments.
÷ The adjustment item is displayed for approximately 20 seconds.
7 Press the TONE key again to return to the input indication.
÷ The TONE key is defeated during tone adjustment in the
SOUND mode (¤,‹) or when the listen mode is
switched to a mode other than the stereo mode.
Press the ACTIVE EQ key for the following selections:
1 "EQ MUSIC " : (The "ACTIVE EQ" indicator lights up)
Effective when listening to music.
2 "EQ CINEMA" : (The "ACTIVE EQ" indicator lights up)
Effective when watching a movie.
3 "EQ GAME" : (The "ACTIVE EQ" indicator lights up)
Effective when playing a game.
4 "EQ OFF" : (The "ACTIVE EQ" indicator goes off)
The ACTIVE EQ function is turned OFF.
÷ ACTIVE EQ function will not be available when REC MODE,
AUTO TUNING or PRESET MEMORY is ON and during 96kHz
LPCM playback.
23 EN
*5484/16-27/EN
23
04.5.17, 8:34 AM
Normal playback
Muting the sound
The MUTE key lets you mute the sound of the speakers or headphones.
Press the MUTE key.
Blinks
To cancel
Press the MUTE key again so that the "MUTE" indicator
goes off.
÷ MUTE ON can also be deactivated by turning the VOLUME
CONTROL knob or pressing the VOLUME +/– keys.
Listening with headphones
1 Connect headphones to the PHONES jack.
2 Use the VOLUME CONTROL knob (or the VOLUME +/–
keys) to adjust the volume.
24 EN
*5484/16-27/EN
24
04.5.17, 8:34 AM
Recording
Analog sources
For AUTO REC mode :
INPUT SELECTOR
A
REC
↓
1 Use the INPUT SELECTOR key (or the input selector key)
to select the source (other than "VIDEO") you want to
record.
2 Put the component connected to the VIDEO jacks to the
record-pause mode.
3 Start playback, then start recording.
DV D
AR
The display switches automatically.
For MANUAL REC mode :
÷ Recording may not be normal for some video software. This
is due to the copy guard condition. fi
M
Digital sources
Switch on the REC MODE to record a digital input source.
Usually use the AUTO REC MODE to record audio input sources.
When the digital mode changes during recording in the AUTO REC
MODE, the audio signal may be interrupted momentarily.
REC
↓
DV D
MR
The display switches automatically.
Recording music in AUTO REC or MANUAL REC mode
When a multi-channel source such as the Dolby Digital or DTS input
signal is recorded in AUTO REC or MANUAL REC mode, the signal in the
current multi channel signal can be recorded down-mixed to 2-channel.
DIMMER
4 Start playback, then start recording.
÷ If the audio reproduction stops in the middle due to change in the
input signals, etc., press the DIMMER key.
INPUT SELECTOR
1 Use the INPUT SELECTOR key (or the Input Selector
keys) to select the source (DVD, VIDEO, FRONT AUX) you
want to record.
2 Put the component connected to the VIDEO jacks to the
record-pause mode.
3 Press and hold the DIMMER key for more than 2 seconds
to select the AUTO REC or MANUAL REC mode.
1 REC mode off
2 "A-REC":
Multi-channel digital signals
(DTS or Dolby Digital) are
down-mixed to 2-channel
before being output fro-m
the analog recording (REC
OUT) jacks.
AUTO REC mode
3 "M-REC":
MANUAL REC mode
When the MANUAL REC mode is selected, the input signal is
down-mixed to 2-channel before being output, but no signal is
output if the source is switched to another digital signal. When
the AUTO REC mode is selected, the type of digital signal is
automatically detected and down-mixed to 2-channel even
when the digital signal is switched.
25 EN
*5484/16-27/EN
25
04.5.17, 8:34 AM
Listening to radio broadcasts
The receiver can store up to 40 stations in the memory and recall them by one-touch operation.
Tuning radio stations
Presetting radio stations
INPUT SELECTOR
BAND
INPUT SELECTOR
AUTO/MONO
MULTI CONTROL @/#
BAND
AUTO/MONO
MEMORY
MULTI CONTROL @/#
1 Use the INPUT SELECTOR key (or the TUNER key) to select
the tuner.
2 Press the MEMORY while receiving the station.
MULTI
CONTROL %/fi
BAND
AUTO 7
TUNING
1/¡
TUNER
)1
875)
Proceed to step 3 within 20 seconds. (If more than 20
seconds elapse, press the MEMORY again).
1 Use the INPUT SELECTOR key (or the TUNER key) to select
3 Use the MULTI CONTROL button (or the MULTI CONTROL % /
the tuner.
2 Use the BAND key to select the desired broadcast band.
4 Press the MEMORY again to confirm the setting.
Each press switches the band.
--
3 Use the AUTO/MONO key (or
88))
fi keys) to select one of the station presets (1 – 40).
• Repeat steps 1, 2, 3 and 4 to store as many stations as
necessary.
• If you store a station at a previously used preset, the old
station will be replaced by the new one.
the AUTO 7 ) to select the
desired tuning method.
Each press switches the tuning method to either auto or manual tuning.
1 Auto tuning:
The "AUTO" indicator lights up
2 Manual tuning:
The "AUTO" indicator goes off
"AUTO" indicator lights up in the display.
88))
÷ Normally, set to "AUTO" (auto tuning). If the radio waves are weak
and there is a lot of interference, switch to manual tuning. (With
manual tuning, stereo broadcasts will be received in monaural.)
4 Use the MULTI CONTROL button (or the MULTI CONTROL %/
fi keys, TUNING 1/ ¡ keys) to select the station.
875)
"TUNED" indicator is displayed when a
station is received."ST." indicator lights
when a broadcast is being received in
stereo.
Auto tuning :
The next station is tuned automatically.
Manual tuning :
Use the MULTI CONTROL button (or the MULTI CONTROL %/fi
keys) to select the desired station.
26 EN
*5484/16-27/EN
26
04.5.17, 8:34 AM
Listening to radio broadcasts
Receiving preset stations
Receiving preset stations in order (P.CALL)
INPUT SELECTOR
INPUT SELECTOR
Numeric keys
P.CALL 4/ ¢
TUNER
1 Use the INPUT SELECTOR key (or the TUNER key) to select
tune as the source.
2 Enter the number of the preset station you want to
receive (up to "40").
Press the numeric keys in the following order:
For "15", press
For "20", press
0,5
0,0,)
• If you make a mistake entering a two digit number, press the +10
TUNER
1 Use the INPUT SELECTOR key (or the TUNER key) to select
tune as the source.
2 Use the P.CALL 4/ ¢ key to select the desired station.
• Each time you press the key, another preset station is received in
order.
Pressing the P.CALL ¢ does the following:
Pressing the P.CALL 4 does the following:
key repeatedly to return to the original display and start again.
Holding down the P.CALL ¢ or 4 key, lets you skip through the
)3
875)
presets, receiving each preset station at 0.5 second intervals.
27 EN
*5484/16-27/EN
27
04.5.17, 8:34 AM
Ambience effects
This receiver is equipped with listening modes that allow you to enjoy an
enhanced sonic ambience with a variety of video sources.
In order to obtain the optimum effect from the surround modes, make
sure to input the proper speaker settings beforehand. *
Surround modes
(Front speakers)
(Center speaker)
C
SW
(Subwoofer)
LS
RS
Dolby Pro Logic IIx was designed specifically to provide a new sense
of spatiality, directionality and articulation of sounds from Dolby
Surround encoded sources.
This is achieved with an intelligent, built-in feedback logic design, a matrix
surround decoding and the decoding of stereo, full bandwidth surround
outputs. The PRO LOGIC IIx modes programmed into this receiver are
"MOVIE", "MUSIC" and "GAME". The "MOVIE" mode of the PRO LOGIC IIx
has preset characteristics to produce a calibrated, high-level surround
sound playback while the "MUSIC" mode has user-adjustable characteristics to offer the three optional controls, like "Dimension", "Center Width"
and "Panorama" modes to allow optimization of the soundfields as
desired. The "Dimension" control allows the user to gradually adjust the
soundfield either towards the front or towards the rear; the "Center
Width" control allows various adjustment of the left-center-right speakers’ balance; the "Panorama" mode extends the front stereo image to
include the surround speakers for an exciting "wraparound" effect with
side wall imaging. The "GAME" mode is designed for playing video
R
L
Dolby PRO LOGIC IIx/ Dolby PRO LOGIC II
(Surround speakers)
games and enhances the powerful feeling of sound.
LB
RB
(Surround back speakers)
Dolby
PRO LOGIC IIx
C
L
R
SW
Dolby Digital EX
LS
RS
Dolby Digital EX is an extension of Dolby Digital technology, Dolby
Digital EX creates six full-bandwidth output channels from 6.1-channel sources. This is done using a matrix decoder that derives three
surround channels from the two in the original recording.
This is achieved by using three different surround signals, Left
Surround, Right Surround, and Back Surround, each driving its own
LB
Dolby
PRO LOGIC II
RB
C
L
R
SW
array of speakers. Think of it as adding a center channel for the rear
speakers, which give more diffuse and natural surround effect, even
LS
if you wanted the ability to completely encircle the audience with
sound, positioning sound effects exactly where they would be heard
in real life.
RS
Note
For best results, Dolby Digital EX should be used with movie
soundtracks recorded with Dolby Digital Surround EX which contain
a digital flag that will automatically activate this feature. However, for
titles released prior to late 2001, this feature has to be activated
manually.
This model lets you enjoy Dolby Digital (and Dolby Surround) program
sources, even if you connect only the Front Speakers. However, in
order to enjoy the benefit of true 6.1 channel Dolby Digital Surround
EX sound, KENWOOD recommends that you connect a full set of
speakers.
L
C
LS
Dolby Digital surround format lets you enjoy up to 5.1 channels of
digital surround sound from Dolby Digital program sources (such as
Laserdisc or DVD software marked
). Compared with previous
Dolby surround, Dolby Digital provides even better sound quality,
greater spatial accuracy, and improved dynamic range.
This model lets you enjoy Dolby Digital (and Dolby Surround) program
sources, even if you connect only the Front Speakers. However, in
order to enjoy the benefit of true 5.1 channel Dolby Digital surround
sound, KENWOOD recommends that you connect a full set of
speakers.
R
SW
Dolby Digital
C
L
RS
R
SW
LB
RB
LS
RS
28 EN
*5484/28-33/EN
28
04.5.17, 8:34 AM
Ambience effects
DTS-ES
DSP mode
The DTS-ES (Digital Theater System-Extended Surround) represents
6.1-channel Discrete Surround format, expanding upon 5.1 surround.
DTS-ES format is a 6.1 channel sound system for movie theaters that
includes an additional surround center channel matrixed within surround left and surround right. It’s compatible on predecessor DTS 5.1
system. The extra channel allows more accurate placement and
steering of sound across the rear soundstage. The DTS-ES receiver
will be required, to experience a discrete 6.1-channel mix.
The DTS-ES decoders used in home cinema systems have decoding
options for utilizing the extra channel, in addition to processing
existing 5.1 channel surround sound :
DTS-ES Discrete 6.1 and DTS-ES Matrix 6.1 add the surround back
channel audio to the DTS 5.1-channel format to improve the acoustic
positioning and makes acoustic image movement more natural with
the 6.1-channel reproduction.
The DSP mode lets you add the atmosphere of a live concert or hall
to almost any type of program source. These modes are particularly
C
L
effective when used with stereo program sources, like CD, television,
and FM radio. You might enjoy trying the ARENA, JAZZ CLUB,
THEATER, STADIUM or DISCO mode the next time you watch a
concert or sporting event!
C
L
R
SW
LS
RS
What's DSP?
R
SW
DSP stands for Digital Signal Processor.
The way a sound is heard in an actual environment depends on a
LS
RS
LB
RB
variety of different factors. One of the most important is reverberation
(the act of decaying elements of sound echoing in various places).
The DSP modes produce the feeling of presence by using the DSP to
create reverberation, without spoiling the sound quality of the original
signal.
NEO:6
NEO:6 is a new technology which decodes 2-channel signals into 6channel signals using high-accuracy digital matrix technology. For the
best results, DTS-ES should be used with movie sound tracks recorded with DTS-ES format which contain a digital flag that will
automatically activate this feature. However, for some titles, this
feature has to be activated manually.
According to the signals to be played back, DTS NEO:6 uses either the
NEO:CINEMA mode optimized for movie playback or the NEO:MUSIC
mode optimized for music playback.
C
L
R
SW
LS
RS
LB
RB
DTS
The DTS employs a larger amount of data than Dolby Digital to play
surround sound with higher quality. The DTS can be used with DVD
and LaserDisc software carrying the
mark. Although the number
of channels is 5.1 and identical to Dolby Digital, the DTS format
features lower audio compression rate in digital recording, which
enables audio with more profoundness and higher S/N. The wider
dynamic range and better channel separation also contribute to make
the surround sound more precise and larger in scale.
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro
Logic”, “Surround EX” and the double-D symbol are trademarks of
Dolby Laboratories.
“DTS”, “DTS-ES Extended Surround” and
C
L
“Neo:6” are trademarks of Digital Theater
Systems, Inc.
R
SW
LS
RS
LFE = Low Frequency Effects. This channel delivers separate nondirectional bass signals to the subwoofer for more dynamic deep bass
sound effects.
When there is a LFE channel input in the DOLBY DIGITAL or DTS
format, the "LFE" indicator lights on the display of the receiver.
29 EN
*5484/28-33/EN
29
04.5.17, 8:34 AM
Ambience effects
Surround play
The desired listen mode can be selected according to the input signal.
Listen modes available with Dolby Digital EX or Dolby Digital
playback: ("Dolby D" indicator lights up)
Main example of medium:
Multi-channel digital source such as DVD.
INPUT SELECTOR
1 "DOLBY D":
DOLBY DIGITAL surround
2 "DOLBY D EX":
DOLBY DIGITAL EX surround *
LISTEN MODE
3 "DOLBY D + PLIIx MOVIE":
DOLBY DIGITAL surround +
DOLBY PRO LOGIC IIx surround MOVIE mode *
4 "DOLBY D + PLIIx MUSIC":
LISTEN MODE
DOLBY DIGITAL surround +
DOLBY PRO LOGIC IIx surround MUSIC mode *
5 "STEREO":
Input selector keys
Normal stereo playback.
* When the speaker setting is set to "BS OFF", the DOLBY DIGITAL EX
and DOLBY DIGITAL + DOLBY PRO LOGIC IIx listen modes cannot be
selected.
÷ You can also adjust the midnight mode as desired.
Preparations
‹
÷ Turn ON related components.
÷ Complete "Preparing for playback" (speaker settings). *
÷ Use the INPUT SELECTOR key (or Input Selector keys) to select
Listen modes available with DTS or DTS-ES (Matrix or
Discrete) playback: ("DTS" indicator lights up)
the component you wish to play back with surround sound.
÷ Use the INPUT MODE key to select the input mode (analog or
Main example of medium:
Multi-channel digital source such as DVD.
digital) for the source you wish to playback. 8
÷ Noise will be produced when a DTS source is played by selecting
the analog input.
1 "DTS":
DTS surround
2 "DTS + NEO6 CINEMA":
1 Start playing the video software.
2 Press the LISTEN MODE key to select the listening mode.
The listening mode settings are stored separately for each input
selector.
If the input mode is set to full auto ("AUTO DETECT" lights), this
model selects the optimal listening mode automatically based on the
type of input signal and the speaker settings.
Each press the LISTEN MODE key switches the setting as
listed.
The listening mode settings are different depending on
the type of input signal.
DTS surround + DTS NEO:6 surround CINEMA mode *
3 "DTS-ES MATRIX 6.1":
DTS-ES 6.1-channel Matrix surround *
4 "DTS-ES DISCRETE 6.1":
DTS-ES 6.1-channel Discrete surround *
5 "STEREO":
Normal stereo playback.
* When the speaker setting is set to "BS OFF", the DTS + NEO:6 CINEMA,
DTS-ES 6.1-channel Matrix and DTS-ES 6.1-channel Discrete listen
modes cannot be selected.
÷ You can also adjust the midnight mode as desired.
30 EN
*5484/28-33/EN
30
04.5.17, 8:34 AM
‹
Ambience effects
Listen modes available with analog or PCM playback:
Main example of medium:
Digital sources including DVD linear PCM and CD.
Analog source such as VCR or radio broadcasting.
1 "PL IIx MOVIE":
DOLBY PRO LOGIC IIx surround MOVIE mode *1
2 "PL IIx MUSIC":
DOLBY PRO LOGIC IIx surround MUSIC mode *1 *2
Dolby Digital Surround EX compliant disc :
Dolby Digital Surround EX compliant disc contains identification signals.
When you choose FULL AUTO during "Input mode settings" (8), this
amplifier detects the identification signals and change the LISTEN mode
to the DOLBY DIGITAL EX (Dolby Digital Surround EX mode) automatically. But sometimes we find some discs which are Dolby Digital
Surround EX compliant disc but it does not contain the identification
signals. If you find the notice like “Surround EX” on the label of disc or
package, you can choose DOLBY DIGITAL EX, then you can enjoy Dolby
Digital Surround EX sound.
3 "PL IIx GAME":
DOLBY PRO LOGIC IIx surround GAME mode *1
4 "PL II MOVIE":
DOLBY PRO LOGIC II surround MOVIE mode
5 "PL II MUSIC":
DOLBY PRO LOGIC II surround MUSIC mode *2
6 "PL II GAME":
DOLBY PRO LOGIC II surround GAME mode
7 "PRO LOGIC":
DOLBY PRO LOGIC surround
8 "NEO6 CINEMA":
DTS NEO:6 surround CINEMA mode
9 "NEO6 MUSIC":
DTS NEO:6 surround MUSIC mode
0 "ARENA":
DSP surround ARENA mode
- "JAZZ CLUB":
DSP surround JAZZ CLUB mode
= "THEATER":
DSP surround THEATER mode
~ "STADIUM":
DSP surround STADIUM mode
! "DISCO":
DSP surround DISCO mode
@ "STEREO":
Normal stereo playback.
*1 When the speaker setting is set to "BS OFF", the DOLBY PRO
LOGIC IIx listen modes cannot be selected.
*2 The sound field can be adjusted as desired using the PANORAMA,
DIMENSION and CENTER WIDTH modes. ¤‹
÷ The listen mode is fixed to stereo when the 96 kHz linear PCM signal
is input.
3 Adjust the volume.
Note
÷ Certain modes may be unavailable depending on the type of input signal
or speaker setting.
÷ If an optimum surround effect cannot be obtained or the desired mode
cannot be selected, check the speaker and input mode settings. 8*
31 EN
*5484/28-33/EN
31
04.5.17, 8:34 AM
Convenient functions
You can make further adjustments to the sound while listening to
playback in the surround mode.
Panorama mode
(Only when the input signal is a 2-channel signal in the DOLBY PRO
LOGIC IIx MUSIC or DOLBY PRO LOGIC II MUSIC mode)
INPUT SELECTOR
When listening to music, you will be able to enjoy the "wraparound"
sound effect when you adjust the panorama mode.
1 Press the RECEIVER key on the remote control unit to set
it to the receiver control mode.
MULTI
CONTROL @ / #
2 Press the SOUND key repeatedly until the "PANORAMA"
indication appears.
3 Use the MULTI CONTROL button (or the MULTI CONTROL
% / fi keys) to select PANORAMA mode "ON" or "OFF".
SOUND
MULTI CONTROL
%/fi
ON
Dimension mode
(Only when the input signal is a 2-channel signal in the DOLBY PRO
LOGIC IIx MUSIC or DOLBY PRO LOGIC II MUSIC mode)
Adjusting the SOUND
When listening to music with certain recordings, you will also be able to
1 Press the RECEIVER key on the remote control unit to set
it to the receiver control mode.
2 Press the SOUND key until the desired item appears in
the display.
Each time you press the button, the menu changes as follows:
Note that some items are not displayed depending on speaker
settings and listening mode.
1 "C": *1
Center speaker level adjustment
2 "RS":*1
Right surround speaker level adjustment
3 "RB": *1
Surround back right speaker level adjustment
4 "LB": *1
Surround back left speaker level adjustment
5 "LS": *1
Left surround speaker level adjustment
6 "SW": *1
Subwoofer level adjustment
7 "INPUT": (Analog mode only)
¡
Input level adjustment
8 "NIGHT": *2
‹
Midnight mode adjustment
9 "PANORAMA": *3
Panorama mode ON/OFF
0 "DIMENSION": *3
Dimension adjustment
- "CENTER WIDTH": *3
‹
Center width adjustment
*1
*2
*3
The setting in the SOUND mode is temporary. It returns
automatically to the original level set in "Speaker settings"
when the receiver is turned OFF/ON.
DOLBY DIGITAL, DTS mode only
Only when the input signal is a 2-channel signal in the DOLBY
PRO LOGIC IIx MUSIC or DOLBY PRO LOGIC II MUSIC mode.
achieve a suitable balance from all the speakers by adjusting the
dimension mode.
1 Press the RECEIVER key on the remote control unit to set
it to the receiver control mode.
2 Press the SOUND key repeatedly until the "DIMENSION"
indication appears.
3 Use the MULTI CONTROL button (or the MULTI CONTROL
%/fi keys) to adjust the soundfield towards the rear or
the front.
Soundfield is adjusted towards the front.
R
Standard setting.
R
R
%/fi keys) to adjust the setting as desired.
÷ The adjustment item is displayed for approximately 20 seconds.
4 Press the SOUND key to advance to the next setting item.
32 EN
32
↓
F
Soundfield is adjusted towards the rear.
3 Use the MULTI CONTROL button (or the MULTI CONTROL
*5484/28-33/EN
↓
F
04.5.17, 8:34 AM
F
Convenient functions
Center Width mode
Display dimmer adjustment
(Only when the input signal is a 2-channel signal in the DOLBY PRO
LOGIC IIx MUSIC or DOLBY PRO LOGIC II MUSIC mode)
The dimmer function lets you select the brightness of the receiver's
Center width adjustment allows you to enjoy an enhanced sound when
listening to music through center image from only center speaker, or left
display. You might find this useful if you darken your room to watch
movies or listen to music.
and right speakers or various combinations adjustments.
1 Press the RECEIVER key on the remote control unit to set
it to the receiver control mode.
2 Press the SOUND key repeatedly until the "CENTER
WIDTH" indication appears.
÷ When the center speaker is switched OFF, this mode will
Each time you press the DIMMER key, the display’s brightness
changes among the three available settings.
Select the brightness level you find most pleasing.
1 Bright
2 Medium
3 Dark
not be effective.
3 Use the MULTI CONTROL button (or the MULTI CONTROL
%/fi keys) to adjust the left-center-right output.
Center image will be heard from center speaker only.
L
R
Center image will be heard from left and right speakers only.
L
R
÷ When in other position, center image from center speaker,
left and right speakers can be heard simultaneously with
various combinations.
Midnight mode
(DOLBY DIGITAL and DTS mode only)
When watching movies at night , you might not be able to raise the
volume as loud as normal. Midnight mode compresses the dynamic
range of previously specified parts of the DOLBY DIGITAL or DTS sound
track (like scenes with sudden increases in volume) to minimize the
difference in volume between the specified and non-specified parts. This
makes it easy to hear all of the sound track, even when listening at low
volumes.
1 Press the RECEIVER key on the remote control unit to set
it to the receiver control mode.
2 Press the SOUND key repeatedly until the "NIGHT"
indication appears.
÷ This can be selected only if DVD, VIDEO or FRONT AUX is
selected as the source and the listen mode is set to "DOLBY
DIGITAL" or "DTS".
3 Use the MULTI CONTROL button (or the MULTI CONTROL
%/fi keys) to select the "NIGHT ON" or "NIGHT OFF"
setting.
1 "NIGHT ON"
2 "NIGHT OFF"
NIGHT
ON
÷ The adjustment item is displayed for approximately 20 seconds.
÷ Some DOLBY DIGITAL or DTS software may not be compatible with the Midnight mode.
33 EN
*5484/28-33/EN
33
04.5.17, 8:34 AM
Basic remote control operations for other components
DVD player operation keys
The remote control of this unit can control two groups of KENWOOD DVD players directly without using the remote control supplied with the DVD player.
Group-1 : DV-4900, DV-4070B, DV-2070, DV-203, DVF-9010, DVF-K7010, DVF-5010, DVF-R9030, DVF-R7030, DVF-3530, DV-402, DV-5900,
DV5700, DVF-R9050, DVF-J6050, DV-505, DV-503, DV-502, DVF-3550, DVF-3050, DVF-R4050, DVF-605, DV-6050, DVF-R5060,
DVF-3060, DVF-3060K, DV-705, DVF-R5070 ,DVF-3070, DVF-3080, DVF-N7080 and DVF-8100.
Group-2 : DV-4050, DV-303, DVF-R6030, DVF-K5020, DVF-5020, DVF-3020 and DVF-3030.
Depending on your KENWOOD DVD model, you need to set up your remote control as follows:
To set for Group-1 DVD players:
Press the numeric “1” key while pressing the “POWER ” key (not the DVD/POWER key) on your remote control.
To set for Group-2 DVD players:
Press the numeric “2” key while pressing the “POWER ” key (not the DVD/POWER key) on your remote control.
• If your DVD player is not listed in the list above, perform the set up for either Group-1 or Group-2. When the set up is successful, then your DVD
player falls into that particular group.
How to operate the DVD player with the remote control
1. Pressing the DVD/POWER key for more than 2 seconds turns the DVD player on or off.
2. To carry out the functions of the DVD player, first press the DVD/POWER key, then press each key for each operation as explained in the DVD
operation pages in the operating instructions. In this case, the DVD operation mode is retained for 15 seconds after pressing any of those DVD
operation buttons.
(To turn the receiver operation mode within 15 seconds, press the RECEIVER key.)
DVD player operation keys
You can perform these basic operations using the keys described below when connected to KENWOOD DVD player.
POWER
Numeric keys
(Select tracks)
ON SCREEN
1
2
3
4
5
6
DVD/POWER
7
8
9
RECEIVER
0
+10
SETUP
LOUDNESS DISC SKIP
SOUND LISTEN MODE INPUT MODE
MENU
%(Cursor »)
fi(Cursor «)
#(Cursor \)
@(Cursor |)
1 (Search)
¡ (Search)
4 (Skip up)
¢ (Skip down)
POWER
DVD/POWER
RECEIVER
(Receiver mode)
DISC SKIP
TOP MENU
(Title)
MENU ON SCREEN RETURN TOP MENU
RETURN
MULTI CONTROL
BAND
TUNING
ENTER
AUTO
DIMMER
TUNER
VIDEO
P.CALL
AUX
F.AUX
DVD
BASS BOOST ACTIVE EQ
ENTER
6 (3 Play)
7 (Stop)
8 (Pause)
TONE
DISC SEL.
DISC SEL.
MUTE
VOLUME
34 EN
*5484/34/EN
34
04.5.17, 8:34 AM
In case of difficulty
Resetting the Microcomputer
The microcomputer may malfunction (unit cannot be operated, or
shows an erroneous display) if the power cord is unplugged while
the power is ON, or due to some other external factor. If this
happens, execute the following procedure to reset the microcomputer and return the unit to its normal operating condition.
Unplug the power cord from the wall outlet, then plug it back in
while holding down the POWER ON/STANDBY key.
÷ Please note that resetting the microcomputer will clear the contents
of the memory and returns the unit to the state it was in when it left
the factory.
Amplifier
Symptom
Remedy
No sound from the speakers.
Sound is not output from the speaker,
or their sound is very small.
÷ Connect them properly referring to "Connecting the speakers"
÷ If muting is ON, release it.
@
¢
÷ If headphones are connected, disconnect them.
÷ Press the INPUT MODE key to select to full auto mode.
¢
8
÷ Connect them properly referring to "Connecting the speakers"
÷ See "Speaker settings" and check if the setting for all of the speakers is correct.
@
*
÷ Select a surround mode.
÷ Adjust the speaker levels using the test tone.
)
The standby indicator blinks and sound
is not output.
÷ Speaker cords are short-circuited. Disconnect the power cord from the AC wall outlet, switch
the receiver OFF, remove the short-circuiting and turn the receiver ON again.
Audio cannot be recorded.
÷ Connect the equipment correctly by referring to "Connecting video components, audio
components" and "Digital connections".
0!
÷ If it is the digital audio that you attempt to record, set up the unit correctly by referring to
"Recording music in AUTO REC or MANUAL REC mode".
∞
A video source cannot be recorded
normally.
÷ Copy-guarded video software cannot be recorded.
When playing a digital source signal,
the sound is cut off soon after it starts.
÷ There are many possible causes for this problem, depending on the type of player used.
Dolby Digital or DTS audio software
cannot be played in multi-channel
audio.
÷ Check if the digital output setting of the digital audio player is correct.
Switch the input mode to DIGITAL MANUAL during playback of the digital source, and restart the
playback from the beginning.
8
Tuner
Symptom
Remedy
Radio stations cannot be received.
÷ Connect an antenna properly.
÷ Set the broadcast band properly.
%
÷ Tune the frequency of the desired station.
§
Interference.
÷ Install the outdoor antenna away from the road.
÷ Turn off the power to the appliance.
÷ Install the receiver farther away from the TV.
A station which was preset cannot be
÷ Preset a station with a receivable frequency.
received by pressing the corresponding
numeric key.
35 EN
*5484/35-40/EN
35
04.5.17, 8:34 AM
In case of difficulty
Remote control unit
Symptom
Remedy
Remote control operation is not
possible.
÷ Press the input selector key and select the optimum control mode.
÷ Replace with new batteries.
÷ Point the remote control unit to the remote sensor of the receiver.
%
÷ Connect them properly referring to "Setting up the system"
÷ The remote control has not been set to the operation mode for the KENWOOD DVD player you
wish to control. Press the DVD/POWER key for more than 2 seconds to activate the operation
mode for the KENWOOD DVD player you want to control before operation.
›
FCC WARNING
Memory back-up function
If the power supply to the receiver is shut down for about a day
or more, the following settings will be reset to the initial conditions. Please be careful.
÷ Power mode = OFF
÷ Volume level = - 66 dB
÷ Dimmer level = OFF (Brightest condition)
÷ Broadcast band = FM
÷ Frequency setting = 87.50 MHz
÷ Tuning mode = AUTO
This equipment may generate or use radio frequency energy. Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this equipment
if an unauthorized change or modification is made.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment may
cause harmful interference to radio communications, if it is not
÷ Listen mode setting = STEREO
÷ Input selector settings = TUNER
installed and used in accordance with the instructions. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
÷ TONE ON/OFF = OFF
÷ LOUDNESS ON/OFF = OFF
÷ BASS BOOST ON/OFF = OFF
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
Note to CATV system installer
interference by one or more of the following measures:
–– Reorient or relocate the receiving antenna.
–– Increase the separation between the equipment and receiver.
This reminder is provided to call the CATV system installer's attention
to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the
–– Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
–– Consult the dealer or an experienced radio / TV technician for help.
point of cable entry as practical.
As an ENERGY STAR® Partner, Kenwood Corporation has determined that this products meets the
ENERGY STAR® guidelines for energy efficiency.
This product can save energy. Saving energy reduces
air pollution and lowers utility bills.
36 EN
*5484/35-40/EN
36
04.5.17, 8:34 AM
Specifications
AUDIO section
FM tuner section
Rated power output during STEREO operation
65 watts per channel minimum RMS, both channels driven,
at 8 Ω from 20 Hz to 20 kHz with no more than 0.7% total
harmonic distortion. (FTC)
Effective power output during STEREO operation ... 100 W + 100 W
(1 kHz, 10% T.H.D. at 8 Ω)
Effective power output during SURROUND operation
FRONT ....................................................................... 80 W + 80 W
......................... (1 kHz, 0.7% T.H.D. at 8 Ω one channel driven)
FRONT ................................................................... 100 W + 100 W
(1 kHz, 10% T.H.D. at 8 Ω one channel driven)
CENTER .................................................................................. 80 W
(1 kHz, 0.7% T.H.D. at 8 Ω one channel driven)
CENTER ................................................................................ 100 W
(1 kHz, 10% T.H.D. at 8 Ω one channel driven)
SURROUND .............................................................. 80 W + 80 W
(1 kHz, 0.7% T.H.D. at 8 Ω one channel driven)
FRONT ................................................................... 100 W + 100 W
(1 kHz, 10% T.H.D. at 8 Ω one channel driven)
Total harmonic distortion .......................... 0.05% (1 kHz, 50 W, 8 Ω)
Frequency response
LINE (DVD, VIDEO, AUX, FRONT AUX)
..................................................... 20 Hz ~ 90 kHz, +0 dB ~ –3.0 dB
Signal to noise ratio
LINE (DVD, VIDEO, AUX, FRONT AUX ) ............................. 96 dB
Input sensitivity / impedance
LINE (DVD, VIDEO, AUX, FRONT AUX) ............ 500 mV / 40 kΩ
Output level / impedance
REC OUT ............................................................. 500 mV / 2.2 kΩ
PRE OUT (SURROUND BACK) .......................... 700 mV / 2.2 kΩ
PRE OUT (SUBWOOFER) ...................................... 1.5 V / 2.2 kΩ
Tone control
BASS ................................................................ ±10 dB (at 100 Hz)
TREBLE ............................................................ ±10 dB (at 10 kHz)
Loudness control
VOLUME at –30dB level .................................. +8 dB (at 100 Hz)
Tuning frequency range ..................................... 87.5 MHz ~ 108 MHz
Usable sensitivity (MONO)
................... 1.3 µV (75 Ω)/ 13.2 dBf (75 kHz dev, SINAD 30 dB)
50 dB quieting sensitivity
STEREO .............................. 28 µV (75 Ω)/ 40.2 dBf (75 kHz dev)
Total harmonic distortion (1 kHz)
MONO .......................................................... 0.5% (71.2 dBf input)
STEREO ....................................................... 0.7% (71.2 dBf input)
Signal to noise ratio (1 kHz)
MONO ........................................................ 75 dB (71.2 dBf input)
STEREO ..................................................... 68 dB (71.2 dBf input)
Selectivity (±400 kHz) ................................................................. 70 dB
Stereo separation (1 kHz) ........................................................... 40 dB
Frequency response (30 Hz ~ 15kHz) ..................... +0.5 dB, –3.0 dB
AM tuner section
Tuning frequency range ..................................... 530 kHz ~ 1,700 kHz
Usable sensitivity (30% mod, S/N 20 dB) ......... 16 µV / (600 µV/m)
Signal to noise ratio (30% mod, 1mV input) ............................ 50 dB
GENERAL
Power consumption .................................................................. 120 W
Dimensions ....................................................... W: 440 mm (17-5/16")
H : 079 mm (3-1/8")
D : 357 mm (14-1/16")
Weight (Net) .................................................................. 7.9 kg (17.4 lb)
DIGITAL AUDIO section
Sampling frequency ...................... 32 kHz, 44.1 kHz, 48 kHz, 96 kHz
Input level / impedance / wave length
Optical (VIDEO, FRONT AUX)
....................................... (–15 dBm ~ –21 dBm), 660 nm ±30 nm
Coaxial (DVD) ....................................................... 0.5 Vp-p / 75 Ω
VIDEO section
Input sensitivity / impedance
Composite (DVD, VIDEO, FRONT AUX) ............... 1 Vp-p / 75 Ω
Output level / impedance
Composite (VIDEO, MONITOR OUT) .................... 1 Vp-p / 75 Ω
Notes
1.KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
2.The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
37 EN
*5484/35-40/EN
37
04.5.17, 8:34 AM
MEMO
38 EN
*5484/35-40/EN
38
04.5.17, 8:34 AM
39 EN
*5484/35-40/EN
39
04.5.17, 8:34 AM
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below. Refer
to the model and serial numbers whenever you call upon your dealer for
information or service on this product.
Model __________________ Serial Number ________________________
*5484/35-40/EN
40
04.5.17, 8:34 AM
Download PDF

advertising