Specifications | Crestron electronic CLW-SW1/4RF Switch User Manual

GLA-PWS50
Functional Summary
The GLA-PWS50 is a 50 Watt Cresnet® Power Supply
designed for use with a Crestron® Green Light™ system,
or anywhere a wall-mountable Cresnet power supply is
needed. The GLA-PWS50 mounts conveniently over a 4”
square or 2-gang electrical box. All connections are made
inside the electrical box via flying leads using twist-on
wire connectors. A partition is included to isolate high
voltage from Class 2 wiring within the box.
•
•
•
•
50 Watt Cresnet power supply
Powers the IPAC and other Cresnet devices
Provides backup power for Crestron Green Light
cabinets
Mounts to a 4” square or 2-gang electrical box
GLA-PWS50 Physical View
Specifications
GLA-PWS50 Specifications
SPECIFICATION
Output Power
Output Power
Ripple/Noise
Power Requirements
Input
Enclosure
Environmental
Temperature
Humidity
Heat Dissipation
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
DETAILS
50 Watts (2.1 Amps) @ 24 Volts
DC, regulated, limited power
source
<1%
0.6 Amps @ 100-240 Volts AC,
50/60 Hz
Metal construction, mounts to a
4-inch square or 2-gang
electrical box, includes lowvoltage partition
32° to 104°F (0° to 40°C)
10% to 90% RH
(non-condensing)
26 BTU/Hr
Dimensions
Height
Width
Depth
4.00 in (10.16 cm)
5.55 in (14.09 cm)
2.27 in (5.76 cm)
Weight
1.2 lbs (0.54 kg)
Installation Guide – DOC. 6734A
(2022081)
02.09
Specifications subject to
change without notice.
50 Watt Cresnet Power Supply
Crestron GLA-PWS50
Industry Compliance
As of the date of manufacture, the GLA-PWS50 has been tested and found to comply with specifications for CE marking.
NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
ƒ
Reorient or relocate the receiving antenna.
ƒ
Increase the separation between the equipment and receiver.
ƒ
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
ƒ
Consult the dealer or an experienced radio/TV technician for help.
2 • Wall Mount 50 Watt Cresnet Power Supply: GLA-PWS50
Installation Guide – DOC. 6734A
Crestron GLA-PWS50
50 Watt Cresnet Power Supply
Application
The following diagram shows a GLA-PWS50 module in a typical application.
GLA-PWS50 in a Lighting Application
Installation Guide – DOC. 6734A
Wall Mount 50 Watt Cresnet Power Supply: GLA-PWS50 • 3
50 Watt Cresnet Power Supply
Crestron GLA-PWS50
Connectors, Controls & Indicators
Physical Description
#
This section provides information on the connections,
controls and indicators available on the GLA-PWS50.
CONNECTORS,
CONTROLS &
INDICATORS
1
LINE POWER
(3) 6” flying leads, 18 AWG, line
power input
Hot (black), neutral (white), and
ground (green/yellow)
connections
2
OUTPUT
(2) 6” flying leads, 18 AWG,
Cresnet power output
+24 VDC (red), G (black/white)
connections
Connects to “24” and “G”
connections of the Cresnet
control network, or directly to a
24 Volt DC powered Crestron
device
3
FUSE
DC output fuse, T3.15AH
(5x20mm, 250V, 3.15A, timelag, ceramic cartridge).
4
24VDC LED
(1) green LED, indicates 24
Volts DC output, extinguishes
when fuse is blown
GLA-PWS50 Overall Dimensions
2.15 in
(5.45 cm)
5.55 in
(14.09 cm)
0.12 in
(0.31 cm)
4.00 in
(10.16 cm)
DESCRIPTION
5.03 in
(12.77 cm)
Setup
GLA-PWS50
1
2
Important Notes
Read before installation.
•
•
3
•
•
Permits: An electrical permit shall be obtained
prior to each installation.
Codes: Install in accordance with all local and
national electrical codes.
Wiring: Use 75°C copper wire only.
Not suitable for Hazardous/Classified areas.
Supplied Hardware
The hardware supplied with the GLA-PWS50 is listed in
the following table.
Supplied Hardware for the GLA-PWS50
4
4 • Wall Mount 50 Watt Cresnet Power Supply: GLA-PWS50
DESCRIPTION
PART NUMBER
QUANTITY
Partition
2022663
1
Plastic Rivet
2005423
3
Twist-On Wire Connector
2005432
5
Installation Guide – DOC. 6734A
Crestron GLA-PWS50
50 Watt Cresnet Power Supply
Assembly
Installation
The GLA-PWS50 comes with a partition to isolate
high voltage from Class 2 wiring when installed in an
electrical box. Refer to the following diagram when
mounting the partition on the GLA-PWS50.
The GLA-PWS50 mounts over a 4” square or 2-gang
electrical box. Refer to the following diagram when
installing the GLA-PWS50.
NOTE: Ensure that the wires will not be pinched during
the installation process by pushing the wires into the
electrical box.
Install the Partition
GLA-PWS50
PARTITION
(2022663), QUAN 1
Install GLA-PWS50 (Wires Removed for Clarity)
4X4 ELECTRICAL BOX (NOT SUPPLIED)
GLA-PWS50
PLASTIC RIVET
(2005423)
QUAN 3
Hardware Hookup
WARNING: RISK OF SERIOUS PERSONAL
INJURY. Turn off power at the circuit breaker(s) prior to
installation. Installing with power on can result in serious
personal injury and damage to the device.
1.
Use two twist-on wire connectors to secure the
Class 2 wiring to the Cresnet network as shown in
the following diagram.
Connect Class 2 Wiring (Partition and High Voltage
Wiring Removed for Clarity)
G
(BLACK)
24
(RED)
4X4 ELECTRICAL BOX COVER SCREWS,
(NOT SUPPLIED), QUAN 4
NOTE: The GLA-PWS50 should never be installed with
the label facing down.
•
To ensure proper ventilation, do not cover the
ventilation holes on the front of the unit.
•
Turn on the circuit breaker after completing
installation. The green LED will illuminate
Fuse Replacement
2.
Use three twist-on wire connectors on the line
input wires to connect to the line power as shown
in the following diagram.
Connect High Voltage Wiring (Partition and Class 2
Wiring Removed for Clarity)
NEUTRAL
(WHITE)
HOT
(BLACK)
GROUND
(GREEN)
If the GLA-PWS50 does not power up when it is
connected to line power, the fuse may need to be replaced.
The fuse holder is located on the right side of the power
supply (next to the LED). To replace the fuse:
1.
Disconnect power to the GLA-PWS50.
2.
Use a flat-head screwdriver to push in the fuse
holder.
3. While pushing in the fuse holder, turn
screwdriver counterclockwise until the fuse
holder pops out.
4.
Remove the fuse from the fuse holder and insert
a new fuse.
FUSE TYPE: 5 x 20mm 3.15A Time Lag
Installation Guide – DOC. 6734A
Wall Mount 50 Watt Cresnet Power Supply: GLA-PWS50 • 5
50 Watt Cresnet Power Supply
CAUTION: Only use the specified type of fuse
when replacing a blown fuse. Failure to do so
may cause damage to the GLA-PWS50.
5.
Insert the fuse holder into the GLA-PWS50.
6.
Push in the fuse holder with a flat head
screwdriver. While pushing in the fuse holder,
turn the screwdriver clockwise until the fuse
holder sinks in.
7.
Push in the fuse holder a little further and turn
the screwdriver clockwise until the fuse holder
locks in place.
8.
Connect power to the GLA-PWS50.
Crestron GLA-PWS50
Return and Warranty Policies
Merchandise Returns / Repair Service
1.
No merchandise may be returned for credit, exchange or
service without prior authorization from CRESTRON. To
obtain warranty service for CRESTRON products, contact an
authorized CRESTRON dealer. Only authorized
CRESTRON dealers may contact the factory and request an
RMA (Return Merchandise Authorization) number. Enclose
a note specifying the nature of the problem, name and phone
number of contact person, RMA number and return address.
2.
Products may be returned for credit, exchange or service with
a CRESTRON Return Merchandise Authorization (RMA)
number. Authorized returns must be shipped freight prepaid
to CRESTRON, 6 Volvo Drive, Rockleigh, N.J. or its
authorized subsidiaries, with RMA number clearly marked
on the outside of all cartons. Shipments arriving freight
collect or without an RMA number shall be subject to refusal.
CRESTRON reserves the right in its sole and absolute
discretion to charge a 15% restocking fee plus shipping costs
on any products returned with an RMA.
3.
Return freight charges following repair of items under
warranty shall be paid by CRESTRON, shipping by standard
ground carrier. In the event repairs are found to be nonwarranty, return freight costs shall be paid by the purchaser.
Problem Solving
Troubleshooting
The following table provides corrective action for
possible trouble situations. If further assistance is
required, please contact a Crestron customer service
representative.
GLA-PWS50 Troubleshooting
CORRECTIVE
ACTION
TROUBLE
POSSIBLE
CAUSE(S)
LED does
not turn on.
Circuit breaker is off.
Verify that circuit
breaker is on.
Fuse is blown.
Check fuse and
replace if necessary.
GLA-PWS50 is not
properly connected.
Verify wiring.
Further Inquiries
If you cannot locate specific information or have
questions after reviewing this guide, please take
advantage of Crestron's award winning customer service
team by calling Crestron at 1-888-CRESTRON
[1-888-273-7876].
You can also log onto the online help section of the
Crestron website (www.crestron.com/onlinehelp) to ask
questions about Crestron products. First-time users will
need to establish a user account to fully benefit from all
available features.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from
manufacturing defects in materials and workmanship under normal use
for a period of three (3) years from the date of purchase from
CRESTRON, with the following exceptions: disk drives and any other
moving or rotating mechanical parts, pan/tilt heads and power supplies
are covered for a period of one (1) year; touchscreen display and overlay
components are covered for 90 days; batteries and incandescent lamps
are not covered.
This warranty extends to products purchased directly from CRESTRON
or an authorized CRESTRON dealer. Purchasers should inquire of the
dealer regarding the nature and extent of the dealer's warranty, if any.
CRESTRON shall not be liable to honor the terms of this warranty if the
product has been used in any application other than that for which it was
intended or if it has been subjected to misuse, accidental damage,
modification or improper installation procedures. Furthermore, this
warranty does not cover any product that has had the serial number
altered, defaced or removed.
This warranty shall be the sole and exclusive remedy to the original
purchaser. In no event shall CRESTRON be liable for incidental or
consequential damages of any kind (property or economic damages
inclusive) arising from the sale or use of this equipment. CRESTRON is
not liable for any claim made by a third party or made by the purchaser
for a third party.
CRESTRON shall, at its option, repair or replace any product found
defective, without charge for parts or labor. Repaired or replaced
equipment and parts supplied under this warranty shall be covered only
by the unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no
other warranties, expressed or implied, nor authorizes any other party to
offer any warranty, including any implied warranties of merchantability
or fitness for a particular purpose. Any implied warranties that may be
imposed by law are limited to the terms of this limited warranty. This
warranty statement supersedes all previous warranties.
Trademark Information
All brand names, product names and trademarks are the sole property of their respective
owners. Windows is a registered trademark of Microsoft Corporation.
Windows95/98/Me/XP/Vista and WindowsNT/2000 are trademarks of Microsoft Corporation.
6 • Wall Mount 50 Watt Cresnet Power Supply: GLA-PWS50
Installation Guide – DOC. 6734A
Download PDF

advertising