Crestron electronic IM-WCCV Network Card User Manual

Crestron IM-WCCV-M
iMedia Wall Plate Computer &
Video Center
Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2007 Crestron Electronics, Inc.
Crestron IM-WCCV-M
iMedia Wall Plate Computer & Video Center
Contents
iMedia Wall Plate Computer & Video Center: IM-WCCV-M
1
Introduction ............................................................................................................................... 1
Features and Functions ................................................................................................ 1
Applications................................................................................................................. 2
Internal Block Diagram ............................................................................................... 3
Specifications .............................................................................................................. 3
Physical Description.................................................................................................... 4
Industry Compliance ................................................................................................... 7
Setup .......................................................................................................................................... 8
Network Wiring........................................................................................................... 8
IM Wiring.................................................................................................................... 8
Installation ................................................................................................................... 9
Hardware Hookup ..................................................................................................... 11
System Configuration................................................................................................ 12
Operation ................................................................................................................................. 13
Problem Solving ...................................................................................................................... 14
Troubleshooting......................................................................................................... 14
Reference Documents................................................................................................ 15
Further Inquiries ........................................................................................................ 15
Future Updates .......................................................................................................... 15
Return and Warranty Policies .................................................................................................. 16
Merchandise Returns / Repair Service ...................................................................... 16
CRESTRON Limited Warranty................................................................................. 16
Operations & Installation Guide – DOC. 6621A
Contents • i
Crestron IM-WCCV-M
iMedia Wall Plate Computer & Video Center
iMedia Wall Plate Computer &
Video Center: IM-WCCV-M
Introduction
Features and Functions
•
•
•
•
•
•
A simple, affordable wall plate multimedia interface
Streamlined user controls for foolproof operation
iMedia transport for fast and easy single cable installation
Supports XGA resolution up to 84 feet (25.6 meters), UXGA maximum
up to 34 feet (10.4 meters)
Supports composite video signals
Complete system setup in minutes using iMedia Wizard software
The iMedia Transport
The iMedia (IM) transport utilizes a single CAT5e* type cable to transmit computer
RGB, video and stereo audio signals to a single projector or plasma display. A
typical XGA signal (1024 x 768 pixels at 60 Hz) can be transmitted up to 84 feet
(25.6 meters) using iMedia, while higher resolutions up to 1600 x 1200 can be
handled over shorter distances. Audio is transmitted digitally at 20-bit, 48 kHz
resolution. Control and power signals are also contained on the same wire,
eliminating the need for separate control or power cables.
*
For optimum performance, Crestron strongly recommends using CRESCAT-IM cable, available from
Crestron. Other high quality, low skew (15 ns per 100 m maximum) CAT5e/CAT6 wiring may also
be used with varying performance.
Wall Plate Multimedia Interface
The IM-WCCV-M is an iMedia transmitter designed to install in a standard threegang electrical box, providing composite video, RGB and stereo audio inputs for
connection to the output of a computer or AV source. Installing wiring for the
IM-WCCV-M is extremely simple requiring just a single CrestCAT-IM cable for
audio and video. Up to three IM-WCCV-Ms or other IM transmitters may be
installed as part of a complete system to provide multiple input locations within the
room.
Operations & Installation Guide – DOC. 6621A
iMedia Wall Plate Computer & Video Center: IM-WCCV-M • 1
iMedia Wall Plate Computer & Video Center
Crestron IM-WCCV-M
Foolproof Operation
Every iMedia system is easy and intuitive to use. A single press of the VIDEO or
PC buttons on the face of the IM-WCCV-M selects the appropriate input, lowers the
screen or lift, turns on the projector (or plasma, etc.) and routes all the signals where
they need to go. The front panel volume control affords easy adjustment of the audio
level or wireless microphone level and the entire system can be turned off at any
time by simply holding down either button for five seconds.
For systems having more than one IM transmitter, selecting an input at a given input
location overrides the previously selected input at any other location. The audio level
for each input location is controlled individually by its respective volume control.
Applications
The IM-WCCV-M is an IM transmitter. As shown in the following diagram, IM
transmitters provide input points for video and PC sources on an IM receiver.
iMedia System Diagram
2 • iMedia Wall Plate Computer & Video Center: IM-WCCV-M
Operations & Installation Guide – DOC. 6621A
Crestron IM-WCCV-M
iMedia Wall Plate Computer & Video Center
Internal Block Diagram
The following diagram represents the signal routing and functions of the
IM-WCCV-M.
Internal Block Diagram of the IM-WCCV-M
VGA
Video
Switch
VIDEO
BUTTON
PC
LED
BUTTON
Microprocessor
VIDEO
Power
Power
Supply
IM
Output
LED
VOLUME
STEREO
AUDIO
Audio
Switch
A/D
COMPUTER
AUDIO
Specifications
Specifications for the IM-WCCV-M are listed in the following table.
IM-WCCV-M Specifications
SPECIFICATION
DETAILS
RGB
Gain
0 dB (75 Ω termination)
Formats
RGBHV, RGBS or RGsB
Resolution
1024 x 768 @ 60 Hz with maximum cable
length of 84 feet, 1600 x 1200 @ 60 Hz with
maximum cable length of 34 feet; refer to
“IM Wiring” on page 8 for other resolutions
Video
Gain
0 dB (75 Ω termination)
Formats
480i (NTSC), 576i (PAL)
Audio
A-D Conversion
20 bit, 48 kHz
Frequency Response
20 Hz to 20 kHz ±1 dB
Power Requirements
Power is provided by the IM receiver via the
IM transport
(Continued on following page)
Operations & Installation Guide – DOC. 6621A
iMedia Wall Plate Computer & Video Center: IM-WCCV-M • 3
iMedia Wall Plate Computer & Video Center
Crestron IM-WCCV-M
IM-WCCV-M Specifications (Continued)
SPECIFICATION
DETAILS
Environmental
Temperature
41º to 104ºF (5º to 40ºC)
Humidity
10% to 90% RH (non-condensing)
Enclosure
Three-gang wall plate, mountable in a 2.5 in
(6.35 cm) deep electrical box;
NOTE: Conduit must enter box via top or
bottom knockouts only
Dimensions
Height
4.50 in (11.43 cm)
Width
6.36 in (16.16 cm)
Depth
2.95 in (7.48 cm)
Weight
1.29 lbs (0.58 kg)
Physical Description
This section provides information on the connections, controls and indicators
available on your IM-WCCV-M.
IM-WCCV-M Physical View
4 • iMedia Wall Plate Computer & Video Center: IM-WCCV-M
Operations & Installation Guide – DOC. 6621A
Crestron IM-WCCV-M
iMedia Wall Plate Computer & Video Center
IM-WCCV-M Physical Dimensions - Front View
Side View
2.95 in
(7.48 cm)
2.48 in
(6.29 cm)
6.36 in
(16.16 cm)
1
2
4.50 in
(11.43 cm)
3
4
5
7
6
Rear View
5.17 in
(13.14 cm)
2.53 in
(6.43 cm)
8
9
Connectors, Controls & Indicators
#
CONNECTORS,
CONTROLS &
INDICATORS
DESCRIPTION
1
VOLUME
(1) Rotary knob, adjusts audio level for local input.
Microphone level is adjusted by holding the
VIDEO or PC button and turning the VOLUME
knob.
(Continued on following page)
Operations & Installation Guide – DOC. 6621A
iMedia Wall Plate Computer & Video Center: IM-WCCV-M • 5
iMedia Wall Plate Computer & Video Center
Crestron IM-WCCV-M
Connectors, Controls & Indicators (Continued)
#
CONNECTORS,
CONTROLS &
INDICATORS
2
VIDEO
3
PC
(1) RCA female, composite video input;
Input impedance: 75 Ω;
Maximum input: 1 Vp-p
PIN1
PIN6
PIN 15
DESCRIPTION
(1) DB15HD female, RGB (VGA) input:
Formats: RGBHV, RGBS, RGsB;
Input impedance: 75 Ω;
Sync impedance: 1 kΩ;
Maximum input level: 1 Vp-p;
Maximum sync level: 5 Vp-p
PIN
FUNCTION
PIN
FUNCTION
1
Red Video
9
No Connect
2
Green Video
10
Ground
3
Blue Video
11
No Connect
4
Reserved
12
Monitor Sense 1
5
Ground
13
Horizontal Sync
6
Red Ground
14
Vertical Sync
7
Green
Ground
15
Monitor Sense 2
8
Blue Ground
4
VIDEO
(1) Pushbutton with green LED; Momentary press
initiates “system power on” command and selects
local VIDEO input; press and hold for five seconds
or more initiates “system power off”.
5
PC
(1) Pushbutton with green LED; Momentary press
initiates “system power on” command and selects
local PC input; press and hold for five seconds or
more initiates “system power off”.
6
AUDIO
(2) RCA female;
Unbalanced stereo line level audio input (linked
with VIDEO);
Maximum input level: 2 Vrms;
Input impedance: 10 kΩ
7
AUDIO
(1) 3.5 mm TRS mini phone jack;
Unbalanced stereo line level audio input;
Maximum input level: 2 Vrms;
Input impedance: 10 kΩ
8
IM1, 2, 3
(1) 8-wire RJ-45 female, iMedia output port;
Connects to IM input port of an iMedia receiver via
CresCAT-IM cable.
1
9
8
GROUNDING
WIRE
(1) flying lead, green, chassis ground wire4.
1. The eight-pin RJ-45 iMedia port accepts CresCAT-IM or CAT5E/CAT6 carrying video, audio, power
and control signals. Refer to the table on the following page for connector pinouts. Power is supplied
to pins 4 and 5 from the IM receivers.
6 • iMedia Wall Plate Computer & Video Center: IM-WCCV-M
Operations & Installation Guide – DOC. 6621A
Crestron IM-WCCV-M
iMedia Wall Plate Computer & Video Center
PIN
WIRE COLORS (EIA 568B)
iMEDIA ASSIGNMENT:RGB,
COMPOSITE AND AUDIO
1
WHITE/ORANGE
2
ORANGE
+ RGB RED
3
WHITE/GREEN
- RGB GREEN
4
BLUE
+ AUDIO / POWER
5
WHITE/BLUE
- AUDIO / POWER
- RGB RED
6
GREEN
+ RGB GREEN
7
WHITE/BROWN
- RGB BLUE / COMPOSITE
8
BROWN
+ RGB BLUE / COMPOSITE
2. For optimum performance, Crestron strongly recommends using CRESCAT-IM cable, available from
Crestron. Other high quality, low skew (15 ns per 100 m maximum) CAT5e/CAT6 wiring may also
be used with varying performance.
3. To determine which is pin 1 on the cable, hold the cable so that the end of the eight pin modular jack
is facing away from you, with the clip down and copper side up. Pin 1 is on the far left.
4. Ensure the unit is properly grounded.
Industry Compliance
As of the date of manufacture, the IM-WCCV-M has been tested and found to
comply with specifications for CE marking and standards per EMC and
Radiocommunications Compliance Labelling.
NOTE: This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Operations & Installation Guide – DOC. 6621A
iMedia Wall Plate Computer & Video Center: IM-WCCV-M • 7
iMedia Wall Plate Computer & Video Center
Crestron IM-WCCV-M
Setup
Network Wiring
When wiring the network, consider the following:
•
Use Crestron Certified Wire.
•
Use Crestron power supplies for Crestron equipment.
•
Provide sufficient power to the system.
CAUTION: Insufficient power can lead to unpredictable results or damage
to the equipment.
IM Wiring
Using a proprietary signal routing solution, RGBHV, audio, power and control
signals are all transported using a single cable solution called iMedia.
The iMedia transport system port is capable of managing computer RGB and audio
signals simultaneously through one CresCAT-IM cable, simplifying installations.
Routing CresCAT-IM cable (low-skew CAT5e) is less expensive and a much
simpler solution for wiring iMedia systems than routing multi-colored, multiconductor coax cable. All Crestron products using the iMedia transport system are
capable of sending and receiving iMedia signals via CresCAT-IM cable. Installation
of any iMedia device is as simple as installing one iMedia cable from output to input.
Installations are affordable and fast.
The receiver can accomplish frequency compensation on each input to achieve
correct operation. This compensation scheme is effective for CresCAT-IM cables as
long as the maximum skew of 15 ns per 100 meters is not exceeded.
NOTE: For optimum performance, Crestron strongly recommends using
CRESCAT-IM cable, available from Crestron. Other high quality, low skew (15 ns
per 100 m maximum) CAT5e/CAT6 wiring may also be used with varying
performance.
Maximum Resolution and Cable Length
RESOLUTION
VGA
(640 X 480)
SVGA
(800 X 600)
REFRESH
RATE
(HZ)
PIXEL
RATE
(MHZ)
PIXEL
TIME (NS)
MAX
LENGTH
(FEET)
60
72
85
56
72
85
25.18
31.50
36.00
36.00
50.00
56.25
39.7
31.7
27.8
27.8
20.0
17.8
218.5
174.6
152.8
152.8
110.0
97.8
(Continued on following page)
8 • iMedia Wall Plate Computer & Video Center: IM-WCCV-M
Operations & Installation Guide – DOC. 6621A
Crestron IM-WCCV-M
iMedia Wall Plate Computer & Video Center
Maximum Resolution and Cable Length (Continued)
RESOLUTION
XGA
(1024 X 768)
SXGA
(1280 X 1024)
UXGA
(1600 X 1200)
REFRESH
RATE
(HZ)
PIXEL
RATE
(MHZ)
PIXEL
TIME (NS)
MAX
LENGTH
(FEET)
60
70
85
60
75
85
60
70
85
65.00
75.00
94.50
108.00
135.00
157.50
162.00
189.00
229.50
15.4
13.3
10.6
9.3
7.4
6.3
6.2
5.3
4.4
84.6
73.3
58.2
50.9
40.7
34.9
34.0
29.1
24.0
218.5
COMPOSITE
VIDEO
For more information on CresCAT and other wire products, visit the Crestron
website (www.crestron.com/downloads/pdf/product_line_overviews/overviewwire_and_cable.pdf).
Installation
The IM-WCCV-M is designed to mount in a standard 2.5 inch (6.35 cm) deep, threegang electrical box.
Tools required:
•
Phillips screwdriver
•
Small flat blade screwdriver (for connecting the VGA cable)
Supplied Hardware for the IM-WCCV-M
DESCRIPTION
Screw #6-32 x 1”, Pan Head, Phillips
Operations & Installation Guide – DOC. 6621A
PART NUMBER
QUANTITY
2007250
4
iMedia Wall Plate Computer & Video Center: IM-WCCV-M • 9
iMedia Wall Plate Computer & Video Center
Crestron IM-WCCV-M
IM-WCCV-M Installation in a Three-Gang Electrical Box
Screws (4) #6-32 x 1"
Standard Three-Gang Electrical Box
(shown with end removed)
Ground Wire
NOTE: To prevent overheating, do not operate this product in an area that exceeds
the environmental temperature range listed in the specifications table. Consideration
must be given if installed in a closed or multi-unit rack assembly, inside a closed
desk, or in a closed podium since the operating ambient temperature of these
environments may be greater than the room ambient. Contact with thermal insulating
materials should be avoided on all sides of the unit.
10 • iMedia Wall Plate Computer & Video Center: IM-WCCV-M
Operations & Installation Guide – DOC. 6621A
Crestron IM-WCCV-M
iMedia Wall Plate Computer & Video Center
Hardware Hookup
Make the necessary connections as called out in the illustrations that follow this
paragraph. Turn on the system only after all connections have been made.
Hardware Connections for the IM-WCCV-M (Front)
VIDEO:
COMPOSITE
VIDEO INPUT
PC:
RGB INPUT
FROM
COMPUTER
AUDIO:
COMPOSITE VIDEO
SOURCE
AUDIO OUTPUT
AUDIO:
AUDIO INPUT
FROM
COMPUTER
Hardware Connections for the IM-WCCV-M (Rear)
IM:
iMEDIA OUTPUT PORT
CARRIES AUDIO AND RGB
SIGNALS TO IM RECEIVER
GROUND WIRE
NOTE: For optimum performance, Crestron strongly recommends using
CRESCAT-IM cable, available from Crestron. Other high quality, low skew (15 ns
per 100 m maximum) CAT5e/CAT6 wiring may also be used with varying
performance.
NOTE: Ensure the unit is properly grounded.
Operations & Installation Guide – DOC. 6621A
iMedia Wall Plate Computer & Video Center: IM-WCCV-M • 11
iMedia Wall Plate Computer & Video Center
Crestron IM-WCCV-M
NOTE: The maximum continuous current from equipment under any external load
conditions shall not exceed a current limit that is suitable for the minimum wire
gauge used in interconnecting cables. The ratings on the connecting unit's supply
input should be considered to prevent overloading the wiring.
System Configuration
Refer to the latest version of the IM-RXV1 & IM-RXV3 guide (Doc. 6478) or the
IM-RXV1-M & IM-RXV3-M guide (Doc. 6593), available from the Crestron
website (www.crestron.com/manuals) for detailed iMedia system configuration
instructions.
12 • iMedia Wall Plate Computer & Video Center: IM-WCCV-M
Operations & Installation Guide – DOC. 6621A
Crestron IM-WCCV-M
iMedia Wall Plate Computer & Video Center
Operation
The IM-WCCV-M can be used to turn a system on or off, select a source, adjust
volume or adjust the microphone level.
Turn on the System
Press the PC button to turn on the system with the PC signals routed to the IM
receiver or press the VIDEO button to turn on the system with the video signals
routed to the IM receiver. The associated LED will light to indicate the selected
source.
Select a Source
Press the PC button to route PC signals to the IM receiver or press the VIDEO
button to route video signals to the IM receiver. The associated LED will light to
indicate the selected source.
Adjust Volume
Turn the volume knob clockwise to raise the volume of the selected input; turn
counterclockwise to lower the volume of the selected input.
Adjust Microphone Level
Microphone level is adjusted by holding either the PC button or the VIDEO
button and turning the rotary VOLUME knob, depending on the source that is
currently selected. For example, if the PC source is selected you would need to
hold the PC button while adjusting the VOLUME knob to adjust the microphone.
When the PC button or VIDEO button is released after adjusting the microphone
volume level, the selected source will remain at the volume setting it had prior to
adjustment of the microphone volume.
Control over the source audio volume level is regained by adjusting the
VOLUME knob without holding down either the PC button or the VIDEO
button. The source volume level will gradually ramp up or down to the level set
by the rotary VOLUME knob.
Turn off the System
Press and hold the selected source button for five seconds. The source button LED
will flash and then turn off.
Operations & Installation Guide – DOC. 6621A
iMedia Wall Plate Computer & Video Center: IM-WCCV-M • 13
iMedia Wall Plate Computer & Video Center
Crestron IM-WCCV-M
Problem Solving
Troubleshooting
The following table provides corrective action for possible trouble situations. If
further assistance is required, please contact a Crestron customer service
representative.
IM-WCCV-M Troubleshooting
TROUBLE
Source LED
does not
illuminate.
POSSIBLE
CAUSE(S)
CORRECTIVE ACTION
Not receiving
power.
Verify that the iMedia cable is
connected to the IM-WCCV-M and
the IM-WCCV-M is connected to
the iMedia receiver.
Incorrect power
supply.
Only use Crestron power supplies.
Source is not
selected.
Push a source button to select a
source.
No video
output
displayed.
Incorrect cable
connection.
Verify computer cable connection.
No audio output.
Incorrect cable
connection.
Verify video cable connection.
Verify iMedia output cable
connection is secure.
Verify computer audio cable
connection.
Verify video input’s audio cable
connection.
No microphone
output.
Microphone level is
incorrectly set.
Set microphone level as described
on page 13.
Video from RGB
source is
garbled or no
output.
Incorrect cable
connections.
Button does not
function when
pressed.
Incorrect cable
connection.
Verify that the iMedia output cable
connection from the IM-WCCV-M to
the iMedia receiver is secure.
Other functions
operate but unit
does not control
the projector.
Incorrect
connections to
projector.
Verify cable wiring and connections
between receiver and projector.
Loss of
functionality due
to electrostatic
discharge.
Verify 15-pin computer cable
connection. Verify iMedia output
cable connections.
Verify maximum iMedia cable length.
Adjust delay on iMedia receiver.
Improper grounding.
14 • iMedia Wall Plate Computer & Video Center: IM-WCCV-M
Verify that all ground connections
have been made properly.
Operations & Installation Guide – DOC. 6621A
Crestron IM-WCCV-M
iMedia Wall Plate Computer & Video Center
Reference Documents
The latest version of all documents mentioned within the guide can be obtained from
the Crestron website (www.crestron.com/manuals). This link will provide a list of
product manuals arranged in alphabetical order by model number.
List of Related Reference Documents
DOCUMENT TITLE
IM-RXV1 & IM-RXV3 iMedia Receiver/Processor with Video
IM-RXV1-M & IM-RXV3-M iMedia Receiver/Processor with Video and Mic Input
Further Inquiries
If you cannot locate specific information or have questions after reviewing this
guide, please take advantage of Crestron's award winning customer service team by
calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876].
For assistance in your local time zone, refer to the Crestron website
(www.crestron.com/offices) for a listing of Crestron worldwide offices.
You can also log onto the online help section of the Crestron website
(www.crestron.com/onlinehelp) to ask questions about Crestron products. First-time
users will need to establish a user account to fully benefit from all available features.
Future Updates
As Crestron improves functions, adds new features and extends the capabilities of
the IM-WCCV-M, additional information may be made available as manual updates.
These updates are solely electronic and serve as intermediary supplements prior to
the release of a complete technical documentation revision.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
Operations & Installation Guide – DOC. 6621A
iMedia Wall Plate Computer & Video Center: IM-WCCV-M • 15
iMedia Wall Plate Computer & Video Center
Crestron IM-WCCV-M
Return and Warranty Policies
Merchandise Returns / Repair Service
1.
No merchandise may be returned for credit, exchange or service without prior authorization
from CRESTRON. To obtain warranty service for CRESTRON products, contact an
authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory
and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying
the nature of the problem, name and phone number of contact person, RMA number and
return address.
2.
Products may be returned for credit, exchange or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped freight
prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with
RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect
or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its
sole and absolute discretion to charge a 15% restocking fee plus shipping costs on any
products returned with an RMA.
3.
Return freight charges following repair of items under warranty shall be paid by CRESTRON,
shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in materials
and workmanship under normal use for a period of three (3) years from the date of purchase from
CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical
parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and
overlay components are covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON
dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if
any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended or if it has been subjected to misuse, accidental
damage, modification or improper installation procedures. Furthermore, this warranty does not cover any
product that has had the serial number altered, defaced or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages
inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for any claim made by a
third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or
labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the
unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or
implied, nor authorizes any other party to offer any warranty, including any implied warranties of
merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are
limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties.
Trademark Information
All brand names, product names and trademarks are the sole property of their respective owners. Windows is a registered trademark
of Microsoft Corporation. Windows95/98/Me/XP/Vista and WindowsNT/2000 are trademarks of Microsoft Corporation.
16 • iMedia Wall Plate Computer & Video Center: IM-WCCV-M
Operations & Installation Guide – DOC. 6621A
Crestron IM-WCCV-M
iMedia Wall Plate Computer & Video Center
This page is intentionally left blank.
Operations & Installation Guide – DOC. 6621A
iMedia Wall Plate Computer & Video Center: IM-WCCV-M • 17
iMedia Wall Plate Computer & Video Center
Crestron IM-WCCV-M
This page is intentionally left blank.
18 • iMedia Wall Plate Computer & Video Center: IM-WCCV-M
Operations & Installation Guide – DOC. 6621A
Crestron IM-WCCV-M
iMedia Wall Plate Computer & Video Center
This page is intentionally left blank.
Operations & Installation Guide – DOC. 6621A
iMedia Wall Plate Computer & Video Center: IM-WCCV-M • 19
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Operations & Installation Guide – DOC. 6621A
(2018828)
09.07
Specifications subject to
change without notice.