Crosley CR 54 CD Turntable User Manual

WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER.
PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
PORTABLE VINYL
TURNTABLE CD/RADIO
CAUTION
RISK OF ELECTRIC
SHOCK
The lighting flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert user to
the presence of uninsulated
"dangerous voltage" within
the product's enclosure
that may be of sufficient
magnitude to constitute
risk of electric shock
to persons.
CAUTION: TO REDUCE
THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE
COVER (OR BACK). NO
USER - SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point
within an equilateral
triangle is intended to
alert user to the
presence of important
operating and
maintenance (servicing)
instruction in the
literature accompanying
the appliance.
CAUTION
For Compact Disc Units Only:
INVISBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED
OR DEFEATED. AVOID DIRECT EXPORSURE TO LASER BEAM.
SPECIFICATION
FREQUENCY RANGE
POWER SOURCE
ANTENNAS
PHONO SPEED CONTROL
POWER CONSUMPTION
SPEAKERS
: AM 520 - 1710 KHz
: FM 87.9 - 107.9 MHz
: AC ADAPTOR INPUT : AC 120V / 60Hz
OURPUT : DC 12V 1.0A
: BUILT-IN FERRITE BAR FOR AM
: BUILT-IN ANTENNA FOR FM
: 33/45/78RPM
: 18 W
: 4 INCH 8 OHM X 2
MODEL: CR 54 CD
INSTRUCTION MANUAL
*DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
910-213500-001
IMPORTANT SAFETY INSTRUCTION
1.
2.
3.
4.
5.
PLEASE READ CAREFULLY ALL THE FOLLOWING IMPORTANT SAFEGUARDS
THAT ARE APPLICABLE TO YOUR EQUIPMENT
Read Instructions - All the safety and operating instructions should be read before the product is operated.
Retain instructions - The safety and operating instructions should be retained for future reference.
Heed Warnings - All warnings on the product and in the operating Instructions shouldbe adhered to.
Follow Instructions - All operating and use instructions should be followed.
Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool; and the like.
8. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven
surfaces may cause the product and cart combination to overturn.
9. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable
operationof the product and to protect it from overheating, and these openings must not be blocked
or covered, The openings should never be blocked by placing the product on a bed, sofa, rug, or
other similar surface.This product should not be placed in a built - in installation such as a bookcase
orrack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
10. Power Sources - This product should be operated only from the type of power sourceindicated
on the marking label, if you are not sure of the type of power supply to your home. Consult your product dealer
or local power company. For products intended tooperate from battery power, or other sources, refer to the operating
instructions.
11. Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet try reversing the plug, If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. Power - Cord Protection - Power - supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they exit from the product.
AC
13. Lightning - For added protection for this product during a lightning storm, or when it is left
Polarized Plug
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the product dueto lightning and power - line surges.
14. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
15. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
16. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short - out parts that could result in a fire or electric shock. Never spill liquid of any kind
on the product.
17. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
18. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions;
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance - this indicates a need for service.
19. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock, or other hazards.
20. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition.
21. Wall or ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. Heat - The product should be situated away from heat sources such as radiators. Heat registers, stoves, or other
products(including amplifiers) that produce heat.
POWER SOURCE
Connect the AC adaptor between the unit and the power outlet
UNPACKING THE TURNTABLE
1.
2.
3.
4.
Carefully remove unit from it's package and take it out of the plastic bag.
Open lid and remove black tie-wrap by untwisting and gently sliding out from under tone arm.
Remove cardboard shipper.
Remove white protective needle cover by gently pulling towards front of unit.
TURNTABLE OPERATION
Press the unit on by switching the POWER (13) located on the front panel to the ON position.
1. Press the PHONO (2) to set the PHONO mode.
2. Set the SPEED CONTROL SWITCH(29) to desire speed (331/3 ,45 or 78 rpm). Place the record on the turntable.
3. Adjust the Volume switch (21/22) set at the mid range.
4. Pull the TONE ARM (28) slightly to the right side until hear the “click” sound to activate the turntable.
5. Move the tone arm by hand out over the record and slowly lower it. Re adjust the VOLUME control (21/22) to the
desire level.
6. At the end of the record, the tone arm will stop automatically by the center and return to the armrest manually.
Accessory: ADAPTER FOR 45RPM
TO PLAY THE 45RPM RECORD, PLACE THE ADAPTER (27) ON THE SPINDLE(26).
BASIC OPERATION
ELectronic volume control display
ELECTRONIC VOLUME CONTROL
a) Press “VOL-DOWN”(21) to reduce the volume, the volume level will be
shown in the LCD panel.
b) Holding down the button will result in continuous decrease of the volume.
c) Press “VOL-UP”(22) will have an opposite result, it is similar to the case of pressing “VOL-DOWN”(21).
USE THE FUNCTION BUTTON TO SELECT THE DESIRED MODE.
CD TOC reading display
a) Pressing “CD” (1) key to set
the CD mode, the TOC reading
starts and will be displayed after finish.
TRACK
Receiving tuning frequency display
b) Pressing “TUNER”(3) key
to set the tuner mode,
and the receiving
tuning frequency will be shown.
FM
MHz
Phono display
c) Pressing “PHONO” key to set the PHONO mode.
The “LINE” will be displayed.
PHONO
EQUALIZER FUNCTION
Manual or Preset Equalizer can be selected by
proper Jumper Setting mentioned on section 5.
If Preset Equalizer is selected,
press “EQ” (16) key results
in the following changes.
Equalizer “ROCK”
FLAT
ROCK
CLASSIC
POP
CD FUNCTION
POWER ON
Switch on the power and press the “CD” (1) key to select the CD mode.
When the lid or tray is closed, reading TOC will start.
If there is no CD inside, a “DISC” display will appear.
Reading TOC
When there is no disc
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful intereference
to radio or television reception, which can be determined by turning the equipment off and on , the user is encouraged
to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio TV technician for help.
After reading display
B) DRAWER TYPE
Press the “OPEN/CLOSE” (18) key
one time to open the tray.
Tray open
Jazz
ROCK
TACK
Put a disc inside and then press the
“OPEN/CLOSE” (18) key one time to close the tray.
After that, reading TOC will start.
Reading TOC
After reading TOC
TRACK
Program input complete
c) Pressing “MEMORY” (10) one time, then track 4 is stored into the
program 1 position. Step (a) to (C) can be used to store
up to 16 tracks into the program or modified the existing program.
TRACK
MEMORY
Play operation
d) Pressing “PLAY/PAUSE”(19) key to play the program.
TRACK
TO PLAY THE DISC
Press “PLAY/PAUSE”(19) to play the CD
e) Press “STOP” (20) when you wish to stop the play.
Searching track 1
Playing track 1
TRACK
(After reading TOC, the disc can start to play anytime.)
TO PAUSE THE PLAYING
Press “PLAY/PAUSE” (19) during the disc is playing,
the playing time will flash.
One more press the “PLAY/PAUSE” (19) key will cancel
the pause condition.
TO STOP THE DISC
CLEAR THE PROGRAM
Pressing the “MEMORY”(10) key one time and then press the “STOP” (20) key, the preset programs will be cancelled.
While paused
a) Press “UP/F-SKIP”(7) or “DOWN/B-SKIP”(6) to
choose a desired track.( Example: The 3rd track)
Each press will change the track number by one.
b) If the CD is stop and the “PLAY/PAUSE”(19) key is
pressed, the CD will start to play from track 3. If the
CD is playing, several seconds after “UP/F-SKIP” (7)
or “DOWN/B-SKIP” (6) is released, the CD will start
to play from track 3.
INTRO PLAY FUNCTION
TRACK
a) During the stop condition, pressing the “INTRO”(8) key to start
the into playing. After that the first 10 seconds of each song
will be played.
Intro setting (Stop condition)
INTRO
b) If the “INTRO” (8) key is pressed again,
the CD will change to the normal playing mode.
Stop condition (TOC display)
Press “STOP”(20) key
TO SPECIFY A TRACK TO PLAY
TRACK
NOTE: If the program is already exist, press the “MEMORY”
and then press the “PLAY/PAUSE”(19) key, the program play will start.
The program will be cleared when the tray is opened or when the lid is opened.
TRACK
TRACK
Intro playing
TRACK
INTRO
RANDOM PLAY FUNCTION
Searching track 3
A) Press ‘RANDOM’ (17) key during CD playing or stop condition.
(Press once again will cancel the function)
Random setting (stop condition)
B) If the CD is under stop condition, press the ‘PLAY/PAUSE’ (19)
key to start the random playing.
During random search
C) If the CD is playing, the random playing will start in next song.
Random playing start
RANDOM
TRACK
TRACK
Play track 3
TRACK
RANDOM
TRACK
(During the CD playing condition, holding down the button will result in fast forward search or fast backward search.)
FAST FORWARD AND FAST BACKWARD
RANDOM
TRACK
Hold down the “UP/F-SKIP” (7) or “DOWN/B-SKIP” (6) button during play.
When the button is held down, there will be a continuous change of CD track’s position.
This change of position can be performed even during pause.
TO CHECK THE REMAINING TIME OF THE DISC
Press ”REMAIN” (12) one time during the disc is playing, then the
display will show the remaining time of the entire disc.
Note: Once the CD program is set, the random function can not
be activated before the program is cleared.
Display of the remaining time
REMAIN
TRACK
If press two more times of the keys, the display will return
to the original condition.
TUNER FUNCTION
REPEAT PLAYING
AUTO SEARCHING A STATION
Note: The type of reception bands, the frequency step, and the upper and lower limits of the
receiving frequency are depended on the specifications of different area.
Press “REPEAT”(9) key one time,“ONE-TRACK REPEAT” will be active.
With one more, “ALL-TRACK REPEAT” will be active.
All track repeat
One track repeat (flashing)
REPEAT
TRACK
REPEAT
AM
KHz
TRACK
With one further press, the repeat mode is cancelled.
PROGRAM PLAYING
AM band selection
During the tuner mode, press “TUNER”(3) to
select the desired reception band.
Broadcasting station in AM
Press “UP/F-SKIP”(7) or “DOWN/B-SKIP”(6) key, and then release
the button when the fast scanning start.The frequency will continue
to change and will automatically stop when a broadcast station is received.
Program input mode
a) In CD mode, Press “MEMORY”(10) key one time.
AM
KHz
TRACK
MEMORY
b) Specify a track to play with “UP/F-SKIP”(7) or
“DOWN/B-SKIP”(6) . (This can also be done with
the numerical keypad in the remote control.)
NOTE: If the “UP/F-SKIP”(7)or “DOWN/B-SKIP”(6) key is pressed during auto searching, the searching will stop at that point.
When the frequency display pass through the upper limit or the lower limit, it will automatically changes to the lower
or the upper limit, respectively.
Choose track 4
TRACK
MEMORY
MANUAL SEARCH A STATION TO RECEIVE A WEAK BROADCAST SIGNAL
Press the “UP/F-SKIP”(7)or “DOWN/B-SKIP”(6) button by one press at a time to adjust the frequency that you wish to receive.
FM STEREO BROADCAST RECEPTION
“STEREO” display will light when a
stereo broadcasting station is receiver.
Stereo reception
STEREO
FM
MHz
PRESETTING METHOD
20 broadcast stations of FM band and 12 stations of AM band can be stored to the preset memory.
a) During tuner mode, by using the auto search
or manual search methods to find a desired
broadcasting station or any desired frequency.
b) Press “MEMORY”(10) key to
make the channel display “_” appear.
Search a desired station
AM
KHz
Memory display
CH
AM
KHz
Choose Channel 1
c) Press “REPEAT=(PRESET)” key to choose the
desired channel
CH
AM
KHz
d) press “MEMORY”(10) again, then the
desired station is stored in channel 1.
Channel 1 presetting finish
CH
AM
KHz
e) Repeat steps (a) to (d) for storing the various broadcast station to other channels or modifying the present channel.
f) To change the broadcast station of a certain channel to a different channel (Example; Change the 1422 kHZ broadcast
station from channel 6 to channel 8)
Press the “REPEAT=(PRESET)” key or the
numerical key to call the broadcast station of
the channel that you wish to change.
(EXAMPLE: Channel 6)
Press “MEMORY” (10) key to the presetting mode
and the channel display “__” appear.
Before change of channel
CH
AM
KHz
Presetting mode
CH
AM
KHz
Press “REPEAT=(PRESET)” to change
the channel
(EXAMPLE: Channel 6 to Channel 8)
Press the “MEMORY”(10) once more, 1422kHZ
is set to channel 8.
After change of channel
CH
AM
LOCATION
OF PARTS
1) CD
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
18)
19)
20)
21)
22)
23)
24)
25)
26)
27)
28)
29)
30)
31)
32)
PHONO
TUNER
SENSOR
LCD DISPLAY
CD / TUNER-BACKWARD SKIP
CD / TUNER-FORWARD SKIP
INTRO
REPEAT=(PRESET)
MEMORY
STAND BY INDICATOR
REMAIN
POWER
CD DOOR
MONO / ST.
EQ
RANDOM
OPEN/CLOSE
PLAY/PAUSE
STOP
VOLUME DOWN
VOLUME UP
MUTE
STAND BY
TURNTABLE
SPINDLE
ADAPTER FOR 45 RPM RECORDS
TONE ARM
SPEED CONTROL SWITCH
ARM REST
ADAPTOR JACK
SPEAKER
1
3
4
5
6
33)
34)
35)
36)
37)
38)
39)
40)
41)
42)
43)
44)
45)
46)
47)
48)
49)
50)
51)
52)
53)
54)
55)
56)
57)
58)
9
10
11
12
RANDOM
17
13
14
OPEN/CLOSE
PHONO
3
2
6
5
9
8
EQ
10+
SKIP BACKWARD
SKIP FORWARD
MEMORY
REPEAT
VOLUME UP
VOLUME DOWN
POWER STAND BY
MUTE
CD
TUNER/BAND
1
4
7
9
PLAY/PAUSE
STOP
18
19
20
21
22
25
23
24
26
27
1422KHz is stored in CH 8
CH
POWER
49
KHz
50
MUTE
33
N/
OPE SE
CLO
NO
52
51
3
54
55
56
57
1
6
5
4
9
8
7
EQ
10+
0
SKIP
/
RY
EAT
MEMO
REP
58
+
-
UME
VOL
30
34
PHO
CD
ER/
TUN D
BAN
2
53
35
36
37
38
39
40
41
42 43
44
45
46
47
48
31
32
Needles are available for additional charges, please call us at 1-800-926-7801
8
15
16
KHz
NOTE: The original memory of channel 6 will not be change during above operations.
7
<Remote Control Function key>
AM
www.crosleyradio.com
2
29
28