Crosley Radio CR44CD Stereo System User Manual

12-9-07
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE. DO NOT REMOVE COVER. PILOT LAMPS SOLDERED IN PLACE. NO
USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
CR44-CD
Turntable Console With CD Player
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER - SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Instruction Manual
The lighting flash with arrowhead symbol, within an equilateral
triangle, is intended to alert user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be
of sufficient magnitude to constitute risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended
to alert user to the presence of important operating and
maintenance (servicing) instruction in the literature accompanying
the appliance.
Specification
Frequency Range
Power Source
Power Consumption
Antennas
Replacement Needle
:
:
:
:
:
:
:
FM 87.5 - 108.5 MHz
AM 525 - 1710 KHz
AC 120V ~ 60 HZ
30 W
External FM Antenna
Built-in Ferrite Am Bar
NP1
* DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
910-242800-0040-100
IMPORTANT SAFETY INSTRUCTION
WARRANTY
PLEASE READ CAREFULLY ALL THE FOLLOWING IMPORTANT SAFEGUARDS THAT ARE APPLICABLE TO YOUR EQUIPMENT
1.
2.
3.
4.
5.
Read Instructions - All the safety and operating instructions should be read before the product is operated.
Retain instructions - The safety and operating instructions should be retained for future reference.
Heed Warnings - All warnings on the product and in the operating Instructions should be adhered to.
Follow Instructions - All operating and use instructions should be followed.
Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool; and the like.
8. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven
surfaces may cause the product and cart combination to overturn.
9. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable
operation of the product and to protect it from overheating, and these openings must not be blocked
or covered, The openings should never be blocked by placing the product on a bed, sofa, rug, or
other similar surface. This product should not be placed in a built - in installation such as a bookcase
or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
10. Power Sources - This product should be operated only from the type of power source indicated on the marking label,
if you are not sure of the type of power supply to your home. Consult your product dealer or local power company. For
products intended to operate from battery power, or other sources, refer to the operating instructions.
11. Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet try reversing the plug, If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. Power - Cord Protection - Power - supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they exit from the product.
AC
13. Lightning - For added protection for this product during a lightning storm, or when it is left
Polarized Plug
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the product due to lightning and power - line surges.
14. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
15. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
16. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short - out parts that could result in a fire or electric shock. Never spill liquid of any kind
on the product.
17. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
18. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions;
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance - this indicates a need for service.
19. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock, or other hazards.
20. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition.
21. Wall or ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. Heat - The product should be situated away from heat sources such as radiators. Heat registers, stoves, or other
products (including amplifiers) that produce heat.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful intereference to radio or
television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio TV technician for help.
Crosley Radio Products are warranted against defects in material and
workmanship for a period of 90 days beginning from the date of sale to the
original purchaser.
Should the unit fail under normal usage during the 90 day warranty period, a
request for RETURN AUTHORIZATION (R.A.) must be made by the original
customer before returning the unit. Call Crosley Radio customer service for
Return Authorization at (502) 583-4246 from 9 AM to 5 PM (EST) Monday to
Friday.
Upon receiving the RETURN AUTHORIZATION number from the Customer
Service Department, properly pack your unit in its original packaging. Include
any adapters, parts, & accessories which were originally provided with the
product, along with a check or money order for $19.95 made out to Crosley
Radio to cover the handling and return postage. Display the R.A. # on the
outside of the carton and ship PREPAID via standard UPS or its equivalent.
ATTN: RETURNS DEP'T
2001 PRODUCTION DRIVE
BAY 2 & 3
LOUISVILLE, KY 40299
CROSLEY RADIO assumes no responsibility for units sent without prior Return Authorization.
The purchaser’s bill of sale is the only proof of warranty entitlement and must accompany the unit.
The warranty does not cover damage due to acts of nature, accident, misuse, abuse, negligence, commercial
use or modification of, or to any part of the product. This warranty does not cover damage due to improper
operation or maintenance, connection to improper voltage supply, or attempted repair by anyone other than
a facility authorized by Crosley Radio to service the product. This warranty does not cover products sold
AS IS or consumables (such as fuses or batteries). This warranty is valid only in the United States.
This warranty gives the purchaser specified legal rights in addition to any rights which may vary from state
to state.
In accordance with the "Moss-Magnuson Warranty Act" of July 10, 1975, this is termed a "limited warranty"
which in no way compromises Crosley Radio‚ high standards of Quality and Workmanship.
UNPACKING
1 Remove packing materials from unit
Note: Save all packing materials.
2 Remove plastic bag covering radio.
3 Remove plastic safety cover from A/C plug.
4 Remove tie from A/C cord.
5 Open lid and remove styrofoam shipping material from turntable.
6 Remove black tie-wrap from under the tone arm.
7 Remove white protective needle cover by gently pulling towards the front of the unit.
8 Untie the FM antenna and allow it to hang down in a straight line for optimum FM reception. If you have
trouble tuning in an FM station, move the external FM antenna for best reception. Do not connect FM antenna
to outside antenna.
Power Source
1 Unwind the AC POWER CORD (31) at the back of the unit and connect it to a
power outlet.
2 Plug A/C cord into appropriate outlet.
3 This product is equipped with a polarized alternating current line plug (a plug having one blade wider than
the other). This plug will fit into the power outlet only one way. This is a safety feature, If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact you electrician
to replace your obsolete outlet. Do not defeat the purpose of the polarized plug.
Turntable operation
Turn the unit on by pressing the POWER BUTTON (6) located on the front panel to the ON position.
1 Slide the FUNCTION SWITCH (4) to PHONO.
2 Set the SPEED CONTROL SWITCH (25) to desire speed (33 1/3,45 or 78 rpm). Place the record on the
turntable.
3 Pull the TONE ARM (24) slightly to the right side until hear the “click” sound to activate the TURNTABLE (22).
4 Move the TONE ARM (24) by hand to the record and slowly lower it to the desired starting point. Turn the
VOLUME KNOB (1) to adjust the volume to the desired level.
5 At the end of the record, the TONE ARM (24) will stop automatically. You must return the TONE ARM (24)
to TONE ARM REST (26) by hand.
Accessory:Adapter For 45 RPM
Slide the FUNCTION SWITCH (4) to RADIO.
Press the AM/FM BUTTON (19) to the select the desired tuning band.
Select the desired radio station by rotating the TUNING KNOB (3).
Adjust the VOLUME KNOB (1) to the desired sound level.
Antenna: for FM reception, the unit is provided with a FM WIRE ANTENNA (30) , move the wire until the
reception is clear and with no interferences. For AM reception, the unit is provided with a directional build-in
ferrite antenna. Rotate the set to find the position in which the best reception is obtained. Do not connect the
FM WIRE ANTENNA (30) to any outside antenna.
Cd operation
Playing a CD
1 Slide the FUNCTION SWITCH (4) to CD.
2 Press the OPEN/CLOSE BUTTON (7) to open the CD DRAWER (11). Place a disc in the tray with the labeled
side of the disc facing up.
3 Press the OPEN/CLOSE BUTTON (7) again to close the CD DRAWER (11). The display will show “—“ for
a few seconds while reading CD information, then the total number of tracks on the disc will be displayed.
“00” will be shown when there is no disc inside the unit.
4 Press the PLAY/PAUSE BUTTON (8) to start playback. The PLAY/PAUSE INDICATOR (9) will light up.
5 Adjust the VOLUME KNOB (1) to the desired volume level.
6 To pause playback, press the PLAY/PAUSE BUTTON (8) . The PLAY/PAUSE INDICATOR (9) will flash. Press
the PLAY/PAUSE BUTTON (8) again to resume playback.
7 To stop playback, press the STOP BUTTON (10) and the PLAY/PAUSE INDICATOR (9) will go off.
Skip Forward And Skip Reverse
1 Press the FORWARD SKIP BUTTON (18) or the BACKWARD SKIP BUTTON (17) to select a track.
2 Press the PLAY/PAUSE BUTTON (8) to start playing the selected track
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
1 Press the PROGRAM BUTTON (15). " 01" will shown on the display and the PROGRAM INDICATOR (16)
will flash.
2 Press the FORWARD SKIP BUTTON (18) or the BACKWARD SKIP BUTTON (17) to select a track.
3 Press the PROGRAM BUTTON (15) again to store the selected track number.
4 Repeat steps 2 and 3 above to program other tracks.
5 Press the PLAY/PAUSE BUTTON (8) to start programmed playback. The PROGRAM INDICATOR (16) will
be on.
6 To erase the programmed sequence, press the STOP BUTTON (10) twice or until the PROGRAM INDICATOR
(16) is off. Programmed tracks will also erase when the CD DRAWER (11) is opened.
NOTE: Maximum of 20 tracks can be programmed to play in any order.
External Speaker
1 This radio is equipped with external speaker outputs.
2 The speaker jacks for external speakers are located on the back of the radio. Beside the speaker jacks is a
switch labeled (int./ext.) When using external speakers, this switch must be switched to the ext. position.
Doing this turns off the internal speakers in the radio and redirects to power to the external speakers.
3 If you decide not to use the external speakers, be sure the switch is on int. or the internal speakers will not
work.
Troubleshooting
Antenna
Volume Knob
Tuner Dial
Tuning Knob
Function Switch
Power Indicator
Power Button
Open/Close Button
Play/Pause Button
Play/Pause Indicator
Stop Button
CD Drawer
LED Display
Repeat Indicator
Repeat Button
Program Button
Program Indicator
1 To repeat a single track, choose the track that you want to repeat, then press the PLAY/PAUSE BUTTON (8)
to start the track. Press the REPEAT BUTTON (14) once to repeat this track. The REPEAT INDICATOR (13)
will flash.
2 To repeat all tracks, press the PLAY/PAUSE BUTTON (8) to start the CD. Press the REPEAT BUTTON (14)
twice to repeat all tracks. Once the CD ends, it will star over again from the beginning of the CD. The REPEAT
INDICATOR (13) will remain on.
3 To erase the repeat function, press the REPEAT BUTTON (14) again until the REPEAT INDICATOR (13) is
off.
1 You can connect your radio to different sources using the auxiliary outputs.
2 Connect auxiliary cables to the LINE OUT JACK (27) to the auxiliary inputs on the desired component. See
the owner’s manual for the operating instructions on the desired component. The LINE OUT JACK (27) only
puts out a signal. Hooking up external speakers alone must be hooked up using the EXTERNAL SPEAKER
JACKS(29).
Radio operation
Location Of Parts
Repeat Playback
Auxiliary Outputs
To play the 45rpm record, place the ADAPTER (23) on the spindle.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
PLAYBACK
1 Press and hold the FORWARD SKIP BUTTON (18) or the BACKWARD SKIP BUTTON (17) to search forward
or backward though the selected track.
2 Release the button at the desired point, playback will resume automatically.
Programmed Playback
AC
Polarized Plug
1
2
3
4
Search Forward And Reverse During Play
Backward Skip Button
Forward Skip Button
AM/FM Button
Speaker
Spindle
Turntable
Adapter For 45 rpm Records
Tone Arm
Speed Control Switch
Tone Arm Rest
Line Out Jack
Speaker Int. / Ext. Switch
External Speaker Jack
FM Wire Antenna
AC Power Cord
VOLUME
There is no Power
1 Make sure the radio is plugged in correctly.
2 Check to see that the power button is pushed in.
There is no Sound
1 Check the volume level by turning the volume knob.
2 Make sure the ext./int. switch on back of radio is on int. (unless you are using external speakers, in which
case it should be on ext.)
Turntable will not work
1 Make sure the function switch is set to phono.
2 Try moving the tone arm to the right until you hear a click.
3 Make sure the protective needle cover is removed.
CD does not play
1 Check to make sure CD is inserted correctly (label side facing up).
2 Check that the surface of the CD is clean
3 Make sure function switch is set to CD.
Needles are available for additional charges,
please call us at 1-800-926-7801
www.crosleyradio.com
21
22
23
24
25
26
27
+
TUNING
CD PHONO RADIO
AM
1
2
3
POWER
OPEN/CLOSE
PLAY/PAUSE
STOP
REPEAT
PROGRAM
B.SKIP
FM
F.SKIP
28
L
R
LINE OUT
INT. EXT.
30
29
VOLUME
+
20
TUNING
CD PHONO RADIO
4
AM
POWER
5
6
OPEN/CLOSE
PLAY/PAUSE
8
7
STOP
REPEAT
10
9
PROGRAM
12 14
11
13
16
15
FM
B.SKIP
F.SKIP
18
17
19
31