Crosley Radio CR89-BT Stereo System User Manual

28-9-07
CR89
1950’S Stack-O-Matic Traveler
Instruction Manual
910-242700-0010-100
28-9-07
IMPORTANT SAFETY INSTRUCTION
WARRANTY
Crosley Radio Products are warranted against defects in material and
workmanship for a period of 90 days beginning from the date of sale to the
original purchaser.
Should the unit fail under normal usage during the 90 day warranty period, a
request for RETURN AUTHORIZATION (R.A.) must be made by the original
customer before returning the unit. Call Crosley Radio customer service for
Return Authorization at (502) 583-4246 from 9 AM to 5 PM (EST) Monday to
Friday.
Upon receiving the RETURN AUTHORIZATION number from the Customer
Service Department, properly pack your unit in its original packaging. Include
any adapters, parts, & accessories which were originally provided with the
product, along with a check or money order for $19.95 made out to Crosley
Radio to cover the handling and return postage. Display the R.A. # on the
outside of the carton and ship PREPAID via standard UPS or its equivalent.
ATTN: RETURNS DEP'T
2001 PRODUCTION DRIVE
BAY 2 & 3
LOUISVILLE, KY 40299
CROSLEY RADIO assumes no responsibility for units sent without prior Return Authorization.
The purchaser’s bill of sale is the only proof of warranty entitlement and must accompany the unit.
The warranty does not cover damage due to acts of nature, accident, misuse, abuse, negligence, commercial
use or modification of, or to any part of the product. This warranty does not cover damage due to improper
operation or maintenance, connection to improper voltage supply, or attempted repair by anyone other than
a facility authorized by Crosley Radio to service the product. This warranty does not cover products sold
AS IS or consumables (such as fuses or batteries). This warranty is valid only in the United States.
This warranty gives the purchaser specified legal rights in addition to any rights which may vary from state
to state.
In accordance with the "Moss-Magnuson Warranty Act" of July 10, 1975, this is termed a "limited warranty"
which in no way compromises Crosley Radio‚ high standards of Quality and Workmanship.
8
1.
2.
3.
4.
5.
PLEASE READ CAREFULLY ALL THE FOLLOWING IMPORTANT SAFEGUARDS
THAT ARE APPLICABLE TO YOUR EQUIPMENT
Read Instructions - All the safety and operating instructions should be read before the product is operated.
Retain instructions - The safety and operating instructions should be retained for future reference.
Heed Warnings - All warnings on the product and in the operating Instructions should be adhered to.
Follow Instructions - All operating and use instructions should be followed.
Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool; and the like.
8. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven
surfaces may cause the product and cart combination to overturn.
9. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable
operation of the product and to protect it from overheating, and these openings must not be blocked
or covered, The openings should never be blocked by placing the product on a bed, sofa, rug, or
other similar surface. This product should not be placed in a built - in installation such as a bookcase
or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
10. Power Sources - This product should be operated only from the type of power source indicated on the marking label,
if you are not sure of the type of power supply to your home. Consult your product dealer or local power company. For
products intended to operate from battery power, or other sources, refer to the operating instructions.
11. Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet try reversing the plug, If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. Power - Cord Protection - Power - supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they exit from the product.
AC
13. Lightning - For added protection for this product during a lightning storm, or when it is left
Polarized Plug
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the product due to lightning and power - line surges.
14. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
15. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
16. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short - out parts that could result in a fire or electric shock. Never spill liquid of any kind
on the product.
17. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
18. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions;
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance - this indicates a need for service.
19. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock, or other hazards.
20. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition.
21. Wall or ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. Heat - The product should be situated away from heat sources such as radiators. Heat registers, stoves, or other
products (including amplifiers) that produce heat.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful intereference to radio or
television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio TV technician for help.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER.
PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
Turntable Operation
General
Accessory: Adapter for 45 rpm
TROUBLESHOOTING
To play a 45rpm record, place the adapter in the
center of the record. This unit includes six (6) adapters
found in the bag with the instruction manual.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lighting flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert user to
the presence of uninsulated
"dangerous voltage" within
the product's enclosure
that may be of sufficient
magnitude to constitute
risk of electric shock
to persons.
CAUTION: TO REDUCE
THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE
COVER (OR BACK). NO
USER - SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point
within an equilateral
triangle is intended to
alert user to the
presence of important
operating and
maintenance (servicing)
instruction in the
literature accompanying
the appliance.
Adapter for 45 rpm
The unit will not operate.
1
Check that the unit is properly connected to an
A/C outlet.
2
Make certain that the small end of the adapter
is plugged in to the power inlet on the turntable.
3
Check the ON/OFF VOLUME KNOB (10) to make
sure it is on.
There is no sound
1
Tone Control
Use the Tone control to adjust the sound quality.
The volume has not been turned up.
Turntable is dragging
1
Make sure the Turntable Suspension Screws are
turned clockwise all the way in to allow the
turntable to sit on the suspension.
CAUTION
For Compact Disc Units Only:
INVISBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED
OR DEFEATED. AVOID DIRECT EXPORSURE TO LASER BEAM.
Specification
Power Supply
Power Consumption
Speed
Speaker
Replacement Needle
:
:
:
:
:
AC adapter -(DC 12V 0.5A)(Included)
15W
33 /45 /78 RPM
4” Dynamic Type x 2
NP1
The Crosley Traveler Stack-O-Matic™ Record
Changer is equipped with a needle designed
specifically to fit Crosley Stack-O-Matic™ Record
Changers. Replacement needles (Model # NP1) are
available for purchase through Crosley Radio at
1-866-CROSLEY.
www.crosleyradio.com
* DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
7
Turntable Operation
Welcome
Turntable Features
1
2
3
4
Selectable 33/45/78 rpm speeds.
5
Adjustable tone control.
to the “AUTO” position. The next record will drop
and begin to play.
11 To stop playback manually, move the TURNTABLE
Load up to 6 records at a time.
Plays 7”, 10”, and 12” records.
Record changer is fully automatic or can be
operated manually.
12
Tone Arm Adjustment
Turntable Instructions
1
Turn power on by rotating the ON/OFF VOLUME
KNOB (10) clockwise.
2
Lift TENSION ARM (1) and rotate counter-clockwise
over the TONE ARM (5).
3
Load desired records on the CENTER SPINDLE
(2). Records should be loaded one at a time.
4
Lift TENSION ARM (1) and rotate it clockwise over
the records and release. TENSION ARM (1) will
automatically pull down onto the records.
5
Set the SIZE SELECT SWITCH (6) to the correct
size of your records.
6
Set the SPEED SELECT SWITCH (4) to the correct
speed of your records.
7
Move the TURNTABLE SWITCH (8) to the “ON”
position. Turntable will begin to turn.
SWITCH (8) to the “OFF” position. Gently lift
the TONE ARM (5) from the record and return
it to the TONE ARM REST (7).
To remove the records from the turntable, lift the
TENSION ARM (1) up and rotate it counterclockwise over the TONE ARM (5). Grab the
edges of the bottom record and lift straight up.
1
2
Do not turn
pulling towards the front of the unit.
3
1
Move the TURNTABLE SWITCH (8) to “AUTO”.
The switch will automatically return back to the
“ON” position and the first record will drop. The
TONE ARM (5) will automatically lift and move to
the beginning of the record. Once the first record
is finished, the TONE ARM (5) will move back to
the TONE ARM REST (7) and the next record
will drop. The TONE ARM (5) will move back to
the beginning of the record. This will repeat until
the last record is finished. When the last record
is finished, the TONE ARM (5) will return to its
rest and the turntable will shut off.
10 To manually switch to the next record during
6
playback, move the TURNTABLE SWITCH (8)
About This Manual
Instructions in the manual describe the controls and
functions of the CR89.
Getting Started
Control Locators........................
Unpacking................................
Set Up......................................
Power Source..........................
4
5
5
5
Turntable
Turntable Features....................
Operating Instructions...............
Tone Arm Adjustment................
Accessory: Adapter for 45 rpm
....................................................
Tone Control...............................
6
6
6
7
7
General
Troubleshooting Guide.............. 7
Warranty..................................... 8
8. Remove white protective needle cover by gently
9
Thank you for purchasing the Crosley 1950’S StackO-Matic Traveler (CR89). Before operating this unit,
please read this manual throughly and retain it for
future reference.
Table of Contents
2
3
Adjust this screw if the TONE ARM(25) is not
raising high enough to clear to the TONE ARM
REST(27). Turn the screw counter-clockwise
to raise the height. Turn the screw clockwise to
lower the height.
Adjust this screw if the TONE ARM(25) drops
on the record too early or too late. Turn the
screw counter-clockwise to start at a later point.
Turn the screw clockwise to start at an earlier
point.
Adjust the screw if you feel there is not enough
tone arm pressure on the record. Turn the screw
counter-clockwise to increase pressure. Turn
the screw clockwise to descrease the pressure.
Note : Adjust the screws one turn at a time and check the
adjustment after each turn.
Getting Started
Getting Started
Unpacking
Control Locator
12
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
TENSION ARM
CENTER SPINDLE
TURNTABLE
SPEED SELECT SWITCH
TONE ARM
SIZE SELECT SWITCH
TONE ARM REST
TURNTABLE SWITCH
TONE CONTROL
ON/OFF VOLUME KNOB
AC ADAPTER
(placed in a white cardboard box, located
at one side of poly-foam)
12. TURNTABLE SUSPENSION SCREW
3
2
1
1
Remove packing materials from unit.
Set Up
1
Plug A/C adapter into appropriate outlet.
Note: Save all packing materials.
5
6
7
8
4
12
2
Remove plastic bag covering unit.
3
Remove tie from A/C adapter.
4
Open lid and remove styrofoam shipping
material from turntable.
5
Remove black tie-wrap from under the tone
arm.
6
Using your Fingers,Turn the Turntable
Suspension Screw (12) clockwise until it is all
the way down. Do not force it. This allows
turntable to float on its shock absorbers.
A/C adapter
Note: This product may be equipped with a
polarized alternating-current line plug (a
plug having one blade wider than the
other.) This plug will fit into the power
outlet only one way. This is a safety
feature. If you are unable to insert the
plug fully into the outlet try reversing the
plug, if the plug should still fail to fit, contact
your electrician to replace your obsolete
outlet. Do not defeat the safety purpose
of the polarized plug.
Power Source
10
Unwind the A/C power adapter (located in a
white box inside the packaging foam). Connect
the small end of the adapter to the back of the
turntable. Connect the other end to an A/C power
outlet.
9
7
Gently pull out the rubber shipping pads.
11
4
5