Cub Cadet 7254 Lawn Mower User Manual

Cub Cadet 7254 Lawn Mower User Manual

26LG3DCH-UA 32LG3DCH-UA

Hospital TVs

Commercial Mode Setup Guide

Note: All features shown within this guide may not be available on all models.

Experienced Installer

Commercial Mode Setup

page 7

Cloning Information

pages 29 / 30 / 31-32-33

©

Copyright 2008, LG Electronics U.S.A., Inc.

For Customer Support/Service, please call:

1-888-865-3026

www.lgcommercial.com

RECORD Model and SERIAL NUMBER

The model and serial number of this TV is located on the back of the cabinet. For future reference, we suggest that you record those numbers here:

Model No._________________Serial No. _______________

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

This product is equipped with a 3-wire grounding-type alternating current line plug. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the three-wire ground type plug.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code

(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics U.S.A., Inc.

Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc.

1000 Sylvan Avenue, Englewood Cliffs, NJ 07632, USA • Phone: 1-201-816-2000.

P A G E 2

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.

2000 Millbrook Drive, Lincolnshire, IL 60069

©

Copyright 2008, LG Electronics U.S.A., Inc.

206-4071

IMPORTANT SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

Important safeguards for you and your new product

This product has been manufactured and tested with safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into the new product, please read and observe the following safety points when installing and using the new product, and save them for future reference.

Observing the simple precautions discussed in this installation and operating guide can help get many years of enjoyment and safe operation that are built into the new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for future reference.

4. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Water and Moisture

Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Power Cord Polarization (Some models)

This product is equipped with a three-wire grounding type alternating-current power plug. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the three-wire ground-type plug.

13. Power Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

PORTABLE CART WARNING

206-4071

P A G E 3

IMPORTANT SAFETY INSTRUCTIONS

(Continued from previous page)

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code

(U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Example of Grounding According to National Electrical

Code Instructions

Ground Clamp

Electric Service

Equipment

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

NEC - National Electrical Code

15. Lightning

For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

16. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits.

When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. If the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

e. If the product has been dropped or the cabinet has been damaged.

f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product.

24. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

P A G E 4

206-4071

Table of Contents

Use this page as a reference to find pages or sections to go to and set up the TV features.

Go to page 7 to begin the Commercial Mode Master TV setup.

1. Connect TV to RF signal and Auxiliary sources.

2. Customize TV features and set up other operational controls in the Installer’s menu.

3. Copy the Master TV setup into the clone programmer.

4. Transfer the Master TV setup from the clone programmer to identical TVs.

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Instructions . . . . . . . . . . . . . . . . . . 3 - 4

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Setup Checklist

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Commercial Mode Setup

. . . . . . . . . . . . . . . . . . . . . . 7

Installer Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

TV Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Typical Installer’s Remote Control . . . . . . . . . . . . . . . . . 10

Remote Key Functions . . . . . . . . . . . . . . . . . . . . . . . . .11

Rear Connections Panel . . . . . . . . . . . . . . . . . . . . . . . . 12

A/V Input 2 Side Connections Panel/RF Antenna Connection 13

MPI Card Slot / PPV Card Installation . . . . . . . . . . . . . . . 14

Vesa Standard TV Mounts . . . . . . . . . . . . . . . . . . . . . . . 15

Pillow Speaker Connections . . . . . . . . . . . . . . . . . . . . . 16

Features Setup Menus Overview . . . . . . . . . . . . . . . . . . . 17

Channel Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Picture Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Audio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Time Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Option Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Lock Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Channel Banks Setup . . . . . . . . . . . . . . . . 24 - 25 - 26 - 27

USB Software Upgrades . . . . . . . . . . . . . . . . . . . . . . . . 28

USB Learn / Teach . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

TLL-1100A Cloning Instructions . . . . . . . . . . . . . . . . . . 30

LT2002 Cloning Instructions . . . . . . . . . . . . . . 31 - 32 - 33

Installer Menus . . . . . . . . . . . . 34 - 35 - 36 - 37 - 38 - 39

References

Detailed Instructions For Making A Master TV . . . . . . . . . 40

Editing Channel Icons/Adding Ch Labels 2-5-4 + Menu Mode 41

Clonable Menu Features Chart . . . . . . . . . . . . . . . . . . . . 42

Checking Software Version . . . . . . . . . . . . . . . . . . . . . . 42

USB Cloning Troubleshooting . . . . . . . . . . . . . . . . . . . . 43

TV Camport Auto Sense Operation . . . . . . . . . . . . . . . . . 44

TV Aux Input Configuration / Power Savings Setup . . . . . 45

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Cloning Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 47

Channel Banks Setup Troubleshooting . . . . . . . . . . . . . . 48

Troubleshooting Flow Chart . . . . . . . . . . . . . . . . . . . . . 49

Commercial Mode Check . . . . . . . . . . . . . . . . . . . . . . . . 50

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Back Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.

1000 Sylvan Avenue

Englewood Cliffs, NJ 07632

For Customer Support/Service please call:

1-888-865-3026

www.lgcommercial.com

206-4071

P A G E 5

Setup Checklist

P A G E 6

Installation and Setup Checklist

__ Unpack TV and all accessories.

__ Install batteries in remote control.

__ Make all connections to signal and Aux sources that will be available.

__ Install TV on Vesa Mount or Stand

Note: It may be advisable to make all hardwire connections before installing on Vesa mount or stand, as appropriate.

Hardware Connections

__ Install any additional hardware as appropriate to your institution.

Hardwire Connections

__ Make all connections to rear Jack Pack.

HDMI/DVI IN

..........

USB IN

SERVICE ONLY

UPDATE

......

RS-232C IN

SERVICE ONLY

.....

RESET

PILLOW

SPEAKER

NORMAL

SPEAKER

R-AUDIO-L

(MONO)

VIDEO

RGB IN (PC)

.....

PILLOW

SPEAKER

Y P

B

VIDEO

P

R

L

AUDIO

R

AUDIO IN

(RGB / DVI)

REMOTE

CONTROL OUT

SPEAKER OUT

8

Installer Menu Items Setup

__ Configure all relevant Installer menu items as required of your institution.

TV Menus Configuration

Configure TV features for the end user.

__ Channel (Auto Tuning Channel Search)

__ Picture

__ Audio

__ Option

__ Time

__ Lock

__ Choose on screen menu language.

(English is the default language.)

Commercial Mode Setup

__ Commercial Mode Setup, see next page.

Channel Banks Setup

__ Configure Channel Banks if applicable.

Software Installation

__ Install or configure any software as applicable; PPV etc.

Additional Features Setup

See page 5, Table of Contents.

__ Select viewing source on TV.

Notes

• If not disabled in Installer menu, Aux sources will appear in channel scan between analog and digital channels after 2-5-5+Menu is performed.

• Scan mode is not functional until 2-5-5+Menu is performed

• Not all TV menu/submenu options are clonable.

• Maximum channels and Aux sources that can reside in the TV controller is 140 channels.

• Channel Banks can be set up after 2-5-5+Menu mode is performed. (Requires remote w/Ch Preview button.)

• The TV controller will not store channel numbers if the numbers are higher than 255.

206-4071

Commercial Mode Setup for Master TV

This page provides an overview of the TV configuration. See the pages referenced for more specific, detailed instructions at each step; how to access and use the Installer menu etc.

Note 1: Disconnect all Aux inputs. Under certain conditions, Auto Tuning (Channel search) is disabled if there is an Aux input active.

Overview: Commercial Mode Setup Procedure

1. Set Installer Menu Items

(Enter TV Installer Menu, see Installer menus for detailed instructions.) a. Set Installer menu item 117 FACT DEFAULT, to 001 and press ENTER on

Installer remote. (This clears all installer menu custom settings, channel labels / icons etc. and reloads the factory default settings.) b. Set Item 003 BAND/AFC.

- Broadcast: set to 000.

- CATV: set to 001.

- HRC: set to 002

- IRC: set to 003 c. Set item 028 CH OVERIDE to 001. This allows access to Auto Tuning,

Manual Tuning and Channel Edit submenus in the Channel Menu.

d. Set other particular installer items that affect your TV programming network. Enable/Disable Aux sources etc. See Installer menu pages.

Note: Disable all Aux sources that will not be active.

e. After all required installer menu item settings have been adjusted, press

ENTER on the remote to remove Installer Menu.

2. Set Up TV Features (See TV Menus section)

Channel, Picture, Sound, Lock, Time, Option (Digital Captions etc).

See TV Clonable Options page.

3. Run Auto Tuning (Channel Search)

(Search for all available channels.) Go to the Channel menu and access the Auto Tuning option, follow onscreen instructions. a. Edit Channel Scan. In the Channel Menu, access Channel Edit.

• Add/Delete channels per your system requirements.

Note: Physical channel numbers are used to identify Virtual channels.

• Add familiar Channel Trademarks/Logos like ABC, CBS, NBC etc. to the

Channel-Time onscreen display. In the Setup menu, select the Channel

Label option. Add identifiable labels for the end user to readily know what common networks are available.

4. Transfer TV Setup to Internal TV Controller: 2-5-5 + Menu Mode

After the TV channel scan has been edited and channel label icons added, enter the Installer menu. Once in the Installer menu, press 2-5-5 and MENU on the remote. This transfers the TV setup to the internal controller box.

Note: The maximum number of channels including Aux sources that can be transferred to the TV controller is 140.

5. Add Custom Channel Labels for analog channels: 2-5-4 + Menu Mode

Enter Installer menu, press 2-5-4 and Menu. Add your own custom labels to channel onscreen displays. Note: Digital Channels often have a broadcaster generated label. When done to exit mode, press MENU.

6. Verify TV Setup

At this point, verify that the channel lineup, channel icons and custom labels are correct. Make sure the TV features are set per your requirements.

Set Installer menu item 028 Ch Overide to 000 to lock the channel scan.

After the preceding has been completed, the Master TV setup is ready to be copied to a Clone Programmer, see Clone programmer pages.

206-4071

HOSPITAL PTC INSTALLER MENU

Typical TV Installer Menu

00X

003 BAND/AFC 00X

001

Review the settings for these

Installer Menu Items

DIGITAL 19-3

MONO STEREO SAP

000

UPN 000-000-000-000 FPGA E0F1

PTC V1.00.000

CPU V3.06.00

WXYZ

Custom Channel Label ‘WXYZ’ created in

2-5-4 + Menu (Add Channel Label) Mode

000

After Master TV setup has been completed, set Installer menu item 028 Ch Overide to 000.

P A G E 7

Typical Connections Panel

UPDATE

Software downloads and debug mode enable/disable.

USB IN

Restricted to service use only

.

HDMI/DVI IN PORT

Connect to output jacks from

HDMI / DVI device.

RESET

Hardware reset to

PTC microcontroller.

HDMI/DVI IN

..........

USB IN

SERVICE ONLY

UPDATE

......

RS-232C IN

SERVICE ONLY

....

RESET

R-AUDIO-L

(MONO)

VIDEO

RGB IN (PC)

.....

PILLOW

SPEAKER

NORMAL

SPEAKER

PILLOW

SPEAKER

RS-232C IN

Provided for updating

TV software.

PILLOW SPEAKER

INPUT PORT

Connect pillow speaker here

.

Y

P

B

VIDEO

P

R

L

AUDIO

R

AUDIO IN

(RGB / DVI)

REMOTE

CONTROL OUT

SPEAKER OUT

8

AUDIO/VIDEO IN 1

Connect to output jacks on audio/video or

S-Video device.

COMPONENT IN

Connect to output jacks on component device.

AUDIO IN (RGB / DVI)

Audio connection for RGB or

DVI device.

RGB IN (PC)

Connection for RGB hookup from PC

P A G E 8

PILLOW SPEAKER

SWITCH

Set to NORMAL SPEAK-

ER to hear TV speakers sound. Set to PILLOW

SPEAKER to hear pillow speaker sound and have

TV controllable with pillow speaker.

SPEAKER OUT

(8-OHM)

Connect to 8 ohm external speaker input.

REMOTE CONTROL

OUT

IR output for controlling an auxiliary device.

206-4071

Headphone Output Port

Connect headphone to this port.

A/V Input 2: Side Connections Panel / RF Antenna Connection

L/MONO-AUDIO-R IN

Connect to audio output jacks from external device.

For only mono audio output, connect to Left audio input.

VIDEO IN

Connect to video output port on external device

.

RF Antenna Connection

RF ANTENNA

Connect to Antenna / Cable input on MPI card.

AV IN 2

Antenna or CATV

ANTENNA

/CABLE

M.P. I.

206-4071

P A G E 9

MPI Card Slot

The MPI card is equipped with an RF jack for antenna/cable signal source connection.

The slot is also available for installing a PPV (Pay-Per-View) card.

MPI Card Removal / PPV Card Installation

1. Remove the two MPI card retainer screws.

2. Pull out current MPI card far enough so that the RF cable can be detached from the old card.

2. Detach RF cable.

3. Place new PPV card into slot and slide it in far enough to reconnect RF cable.

4. Reconnect RF cable.

5. Insert card all the way into the slot making sure it is fully seated into back plane connector.

6. Replace the two card retainer screws.

ANTENNA

/CABLE

M.P. I.

M.P. I.

Card Slot

RF CABLE

RF cable needs to be disconnected to remove current card

.

P A G E 1 0

206-4071

Vesa Standard TV Mounts

General Guidelines: Choosing a

Location for installing a VESA Standard

Mount

To the right are some examples of VESA standard mounts. Since there are numerous types of stands and mounts available, only a few are shown here. Refer to the instructions provided with the TV stand that will be used to mount the TV. Be sure the style of stand selected is capable of supporting the weight of the TV and is appropriate for the application.

Wall Mounts

If the mount will be on a wall, a typical wooden stud behind the wall board would be the preferred choice for a location to attach the wall mount. The wall mount location chosen should be appropriate for drilling holes and have available the required power source as well as antenna/cable and any other equipment leads as necessary.

Pedestal Mounts and Stands

A sturdy surface on a desk or other similar flat table-like furniture would be the appropriate location for mounting a pedestal-style TV stand.

Most stands are designed so that the wiring is threaded through the stand itself or a loopthrough style clamp so that the wiring is neatly bunched and not strung in such a way as to create a potential hazard to the user.

(Some stands are portable and can be moved from one location to another.) Be sure all safety considerations are followed.

206-4071

Typical Wall Stud Type Mount with Swivel

Bracket

Typical Pedestal Type Mount with

Swivel Bracket

P A G E 1 1

Installer Overview

Operating Installer Menu

To set up the controls for the TV you will need to know how to enter the TV Installer menu and make changes to the default values. If necessary, familiarize yourself with the TV Installer menu and how to make and save changes to the items in the menu.

LG Installer Remote

You will need an LG Installer remote control similar to the one shown to the right. The installer remote must have a “Source” button or its equivalent. The remote shown for reference in this manual has “INPUT” -- this button serves the purpose of a Source button.

The TV’s clonable features need to be set up. This is a critical step.

If the Master TV display panel’s clonable features like added channel icons or channel labels are not done correctly, then the cloned TVs will all have problems. Refer to the TV menus for other TV features:

Picture, Audio, Option, Closed captions, Lock (V-Chip), etc.

TLL-1100A Clone Programmer

The TLL-1100A is a very simple cloner to use. It can

TV Link

Loader-Demo be set up to clone a master TV setup and transfer it into a target TV. Cloning is possible using MPI proto-

TLL1100A

Ready

MODE

MENU col. Be sure the Master TV is set up completely.

Cloning is only possible when the signal source is an

Analog channel, not a digital channel. Refer to TLL-

1100A instruction manual supplied with the cloner.

ENTER

RECEIVE SEND

TLL1100A

HOSPITAL PTC INSTALLER MENU

000

UPN 000-000-000-000 FPGA E0F1

PTC V1.00.000

CPU V3.06.00

Typical Installer Menu

INPUT

TV

INPUT

POWER

MULTI

MODE

TV

DVD

VCR

EZ PIC EZ SOUND SWAP INFO

EXIT

CC

MENU

RATIO

SAP

ENTER

1

4

7

VOL

TIMER

MUTE

CH PAGE

2

5

8

0

9

FLASH

BACK

3

6

P A G E 1 2

206-4071

TV Overview

Notes

• See the Installer’s menus to set up the operational features of the TV. The Installer’s section content is intended to be used primarily by qualified TV electronics technicians.

• Reference is made to installer remote controls used for menu operation within the manual. The remote information is provided for reference only. The typical installer remote control shown for reference in this manual may be different than the actual remote control used to configure the TV.

• For any additional information, contact your LG representative.

Note: Design and specifications are subject to change without prior notice.

Using the 32LG3DCH-UA Hospital TV, the patient has available the following entertainment options.

• Pillow Speaker control of TV.

• Auxiliary inputs on side connections panel, if enabled.

• Analog and Digital programming entertainment as provided by hospital:

VHF, UHF, DTV, CATV, CADTV.

• 32 Inch screen size.

• 16:9 Aspect Ratio.

• SRS Surround Sound

• Digital Captions

• Tier programming as available through Channel Banks setup, RF delivered programming content options for premium as well as basic entertainment packages.

• Side headphone(s) output jack.

206-4071

P A G E 1 3

Typical Installer Multi-Brand Remote Control

P A G E 1 4

INPUT

TV

POWER

INPUT

MULTI

MODE

TV

DVD

VCR

EZ PIC EZ SOUND SWAP INFO

EXIT

CC

MENU

RATIO

SAP

ENTER

1

4

7

VOL

TIMER

MUTE

CH PAGE

8

0

2

5

9

FLASH

BACK

3

6

LG Multi-brand Remote Control

Use the MODE button to select TV and put installer remote into TV operating mode.

Notes: This remote is not supplied with the TV. This typical LG multibrand remote control is shown for reference.

See next page for typical key functions in TV operating mode.

Follow the instructions provided in the Installer menu section to configure the TV’s features.

AA

+

AA

+

Installing Batteries in Installer Remote Control

• Remove the battery compartment cover on the back side by pressing the arrow tab forward and lifting. Install batteries matching correct polarity as shown (+ with + and - with -).

• Install two high-quality alkaline 1.5V AA batteries. Never mix old or used batteries with new ones. Replace cover.

206-4071

Installer Remote Control Typical Key Functions

Remote Control Key Functions. To put remote into TV operating mode, select TV with the MODE key.

Notes: This remote is not supplied with the TV. This typical LG multi-brand remote control is shown for refer-

ence. Follow the instructions provided in the Installer menu section to access the Installer menu.

TV INPUT/INPUT

Select available input sources.

POWER

Turns your TV or any other programmed equipment On or Off, depending on mode.

MULTI

Selects RGB, HDMI,DVI, HDMI2 and Component

Input sources.

Adjusts picture brightness.

EZ PIC

Selects the factory preset picture appropriate for the viewing environment.

EZ SOUND

Sets the appropriate sound for the program’s content.

SWAP

Exchanges the main/sub images in

Twin picture mode.

INFO

While watching a TV program, will display program information on top of the screen. Info feature is not functional for Aux sources.

THUMBSTICK

Up/Down/Left/Right/ENTER

Use to navigate on-screen menus / adjust the system settings to your requirements.

VOLUME UP/DOWN

Increases/decreases the sound level.

TIMER

Sets the amount of time before the TV automatically turns itself Off.

MUTE

Switches the sound on or off.

CHANNEL UP/DOWN/PAGE

Selects available channels found with EZ Scan.

Moves to next available page.

NUMBER Buttons (0 - 9) DASH

Use to enter a program number or channels.

Dash for multiple channels such as 9-1, 9-2, etc.

FLASHBK

Returns to the previously viewed channel.

INPUT

TV

INPUT

POWER

MULTI

MODE

TV

DVD

VCR

EZ PIC EZ SOUND

SWAP INFO

EXIT

CC

MENU

RATIO

SAP

ENTER

1

4

7

VOL

TIMER

MUTE

CH PAGE

8

0

2

5

9

FLASH

BACK

3

6

MODE

Selects remote operating mode: TV, VCR, or DVD.

Select these other operating modes for remote to operate external devices.

VCR/DVD BUTTONS

Control some video cassette recorders or DVD players. (“RECORD” is not functional in DVD mode.) Set up for VCR recording: Once, Regularly,

Weekly, Off. (“RECORD” button only).

EXIT

Clears all on-screen displays and returns to TV viewing from any TV menu.

CC

Selects a closed caption option:

Off, CC1 ~ 4, Text1 ~ 4.

MENU

Brings up the main menu to the screen.

Enters or exits a Panel Menu in the TV Guide on-screen menu system.

RATIO

Adjusts the picture aspect ratio.

SAP

Selects MTS sound:

Mono, Stereo, and SAP in Analog mode.

Changes the audio language in DTV mode.

SAP Notes

• SAP settings are retained with power off/on for individual analog channels.

• If SAP is selected and no SAP is provided, sound will not be heard on channel.

• Each analog channel may have its own SAP setting.

• Digital channels will reset to default audio language with a power off/on.

206-4071-C

P A G E 1 5

Pillow Speaker Connections

Set up Pillow Speaker after commercial mode setup and cloning procedures are complete

Pillow Speaker Setup

PILLOW

SPEAKER

NORMAL

SPEAKER

PILLOW

SPEAKER

Pillow Speaker used in your system?

- Connect pillow speaker and slide control switch to ‘Pillow Speaker’ to control TV and hear audio on pillow speaker.

- For TV speakers sound with pillow speaker control, set switch to ‘Normal

Speaker’ on connections panel.

TV

Controlling the TV with Mechanical

Switches

Pin 4 (common) is momentarily connected to pin 1, 3, or 6 via push-action switches to control power On/Off and

Channel Up/Down. These pins are at

+13 volts DC (when measured from pin

4) with the switches open. Current draw is 8 mA when a switch is closed.

(This operation is identical to previous models using the 5-Wire Interface except that only +7 volts DC was supplied and current draw was only 2.5

mA.)

SPKR.

TV

VOLUME CONTROL

ON/OFF

CHAN

DOWN

5

1

4

6

2

3

(MALE

PLUG)

CHAN

UP

Pillow Speaker Control

Pillow Speaker Interface

This connector furnishes three control lines and an audio output. A patient-pendant remote control, or entertainment audio and nurse call system may be connected here. All lines are isolated from the AC power line and earth ground. (Opto-isolators isolate the control lines, and a transformer isolates the audio. There are no relays or inductive components in the control lines.)

4

5

6

1

2

3

4

5

1

6

2

3

TV ON/OFF

OPEN

CHAN UP/DATA IN

COMMON

AUDIO OUT

CHAN DOWN

Pin No. Purpose

1 External TV On/Off switch.

3

4

5

6

External Channel Up switch or Data in.

Common connection for control, data, and audio output. Impedance to earth ground is a 10-meg resistor in parallel with a 1100 pf capacitor.

Isolated audio output. Nominal 14-ohm source impedance with short circuit protection. Intended for a pillow speaker with a low-impedance pad-type volume control.

External Channel Down switch.

P A G E 1 6

206-4071

The onscreen menus allow the Installer to set up the basic TV features

Basic TV Features Setup

206-4071

CHANNEL PICTURE

AUDIO

TIME OPTION LOCK

CHANNEL

Auto Tuning

Manual Tuning

Channel Edit

Channel Label

Move Enter

PICTURE

Aspect Ratio

Picture Mode

: 16:9

: Vivid

- Backlight 100

-Contrast 100

- Brightness 50

- Sharpness 50

- Color 50

- Tint 0

Move Enter

AUDIO

Auto Volume

Clear Voice

Balance

Sound Mode

Move

: Off

: Off

: 0 :

: Standard

- SRS TruSurround XT :Off

- Treble 50

- Bass 50

- Reset

Enter

TV Speaker: On/Off

LOCK

Lock System

Set Password

Block Channel

Movie Rating

TV Rating-Children

TV Rating-General

Move

:Off

Enter

Input Block

OPTION

Language

Caption

Move

:English

: Off

Enter

TIME

Clock

Off Time

On Time

Sleep Timer

Auto Sleep

Move

: - - - -, - - - - , - - : - - - -

:Off

:Off

:Off

:Off

Enter

P A G E 1 7

Channel Menu

The Channel menu contains the channel search and channel scanning setup options

CHANNEL PICTURE AUDIO

TIME OPTION LOCK

CHANNEL

Auto Tuning

Manual Tuning

Channel Edit

Channel Label

Move Enter

Purpose

Searches for analog and digital channels.

Gives the Installer the option to manually add channels to channels list in TV memory.

Shows signal strength for selected channel.

Allows Installer to add/delete channels in channel memory.

Adds an identifying logo to channel time OSD.

Channel Menu Navigation

Typical Menu Operation

Auto Tuning (Channel Search)

1. Press Menu on the Installer remote.

2. Select the Channel Menu Option and press

Enter.

3. Go to the Auto Tuning option with the

Up/Down/Left/Right arrow keys.

4. Press Enter.

5. Press Enter again to start the channel search.

6. Press Menu to remove Channel menu from screen.

P A G E 1 8

206-4071

Picture Menu

The Picture menu settings control the appearance on the TV picture

CHANNEL PICTURE

AUDIO

TIME OPTION LOCK

PICTURE

Aspect Ratio

Picture Mode

: 16:9

: Vivid

- Backlight 100

-Contrast 100

- Brightness 50

- Sharpness 50

- Color 50

- Tint 0

Move

Enter

Purpose

Sets the picture proportion.

Selects factory preset picture options.

Also allows the Installer to specify custom picture setups.

Note: There are additional menu options accessible with the down arrow.

Advanced Control

Reset

Picture Menu Navigation

Typical Menu Operation

Picture Mode

1. Press Menu on the Installer remote.

2. Select the Picture Menu Option and press Enter.

3. Go to the Picture Mode option with the

Up/Down/Left/Right arrow keys.

4. Press Enter.

5. Use the Up/Down/Left/Right arrow keys to select Picture Mode. Choose from preset or make custom picture appearance settings.

6. Press Menu to remove Picture menu from screen.

206-4071

P A G E 1 9

Audio Menu

The Audio menu configures the TV sound options

CHANNEL PICTURE AUDIO

TIME OPTION LOCK

AUDIO

Auto Volume

Clear Voice

Balance

Sound Mode

Move

: Off

: Off

: 0 :

: Standard

- SRS TruSurround XT :Off

- Treble 50

- Bass 50

- Reset

Enter

TV Speaker: On/Off

Purpose

Enables and disables the Auto Volume option.*

Enables and disables the Clear Voice option.

Gives the Installer the option to set the sound output more to the Left or to the Right speaker.

Selects preset optimum audio output based on program content. The Installer can also make custom sound settings.

Note: There are additional menu options accessible with the down arrow.

Audio Menu Navigation

Typical Menu Operation

Sound Mode

1. Press Menu on the Installer remote.

2. Select the Audio Menu Option and press Enter.

3. Go to the Sound Mode option with the

Up/Down/Left/Right arrow keys.

4. Press Enter.

5. Select from the preset sound output options or make custom sound settings.

6. Press Menu to remove Audio menu from screen.

* Note: Auto Volume is disabled if the Pillow Speaker switch is set to ‘Pillow’ Speaker’.

P A G E 2 0

206-4071

Time Menu

The onscreen menus control the basic TV features

CHANNEL PICTURE AUDIO

TIME OPTION

LOCK

TIME

Clock

Off Time

On Time

Sleep Timer

Auto Sleep

Move

: - - - -, - - - - , - - : - - - -

:Off

:Off

:Off

:Off

Enter

Purpose

Set the internal clock on the TV automatically or manually.

Sets a time the TV will automatically turn Off each day.

Sets a time the TV will automatically turn On each day.

Sets a time the TV will turn itself Off, once.

Time Menu Navigation

Typical Menu Operation

Sleep Timer

1. Press Menu on the Installer remote.

2. Select the Time Menu Option and press Enter.

3. Go to the Sleep Timer option with the

Up/Down/Left/Right arrow keys.

4. Press Enter.

5. Select a Sleep Timer TV turn Off time.

6. Press Menu to remove Time menu from screen.

206-4071

P A G E 2 1

Option Menu

The Option menu can be used to configure digital captions for the end user

OPTION

Language

Caption

CHANNEL PICTURE

AUDIO

TIME OPTION

LOCK

Move

:English

: Off

Enter

Purpose

Selects English, Spanish or French.

Enters the captions setup menu.

Allows the Installer to specify which analog or digital captions will appear.

The Installer can customize the appearance of the digital captions.

P A G E 2 2

Option Menu Navigation

Typical Menu Operation

Caption

Turns captions On/Off and enters submenus

1. Press Menu on the Installer remote.

2. Select the Option Menu and press Enter.

3. Go to the Captions option with the

Up/Down/Left/Right arrow keys.

4. Press Enter.

5. Set up Caption menu and Digital Captions submenus options.

6. Press Menu to remove Option menu from screen.

206-4071

Lock Menu

The Lock menu can be used to set up V-Chip (Parental Control)

CHANNEL PICTURE AUDIO

TIME OPTION LOCK

LOCK

Move

Lock System

Set Password

Block Channel

Movie Rating

TV Rating-Children

TV Rating-General

Downloadable Rating

Input Block

:Off

Enter

Purpose

Enables and disables the parental lock.

Sets the V-Chip password.

Allows the Installer to block individual channels.

The remaining Lock menu options set up individual V-Chip controls for programming that can appear.

If provided on program, additional blocks can be set to restrict programming that can appear.

206-4071

Lock Menu Navigation

Typical Menu Operation

Lock System

1. Press Menu on the Installer remote.

2. Select the Lock Menu Option and press Enter.

3. Go to the Lock System option with the

Up/Down/Left/Right arrow keys.

4. Press Enter.

5. Set the Lock system to be enabled or disabled.

Set up V-Chip blocks for the available Parental

Control options.

6. Press Menu to remove Lock menu from screen.

Note: Installer can enter 7-7-7-7 to access Lock menu if it is active and password is not available.

P A G E 2 3

Channel Banks Overview

Channel Banks Note: Disable all Aux sources in the Installer menu that will not be made available to the end user.

Channel Banks Overview

Purpose of Channel Banks: Allows the institution administrator to control access to patient in-room TV programming. A channel bank can be enabled for a patient for a pre-determined fee. For Banks 1-2 and 3, the institution can create programming levels. Each level would offer a custom channel line-up. Top tier would be the most programming (premium etc.), 2nd tier=lesser programming, 3rd tier=basic programming etc. Channel Bank 4 would display the ‘Inactive TV Call Attendant’ message when the

TV is turned on. The administrator could activate Banks 1-2 or 3 depending on the programming tier selected by the patient. When the patient leaves the hospital, the administrator can then select Bank 4 to reinstate the Inactive TV message.

Channels Available Charts

All channels found in the channel search are included in all channel banks. Default is for all channels to be active in channel banks 1-2-3 and 4. Create channel banks charts similar to the examples on the following pages. Show on the channel bank chart, the status for each channel in all channel banks. This then becomes the patient entertainment programming offerings plan.

Channel Banks Setup

Operating the Channel Banks menu.

Note: Channel banks can only be set up after the 2-5-5+Menu procedure has been completed. See remote key functions for channel banks menu on the following page.

Channel Status Options Available for Channel Banks

In the Ch Preview-Channel Banks menu, use the channel up-down arrows to go to a channel and the Left-Right arrows to select the channel status. See channel status chart.

Inactive TV Setup

Go to Channel Bank 4. Select ‘Normal Delete’ for all channels. When the TV is powered on by the patient, the ‘Inactive TV Call Attendant’ message will appear on the screen and after a few moments the TV will turn itself off. With the Installer remote, the administrator can activate Banks 1, 2 or 3 depending on the entertainment programming tier selected by the patient. When the patient leaves the hospital, the administrator can then select Bank 4 to reinstate the ‘Inactive TV’ message.

Note: Default setting for Aux sources is to be active in the Installer menu. The Aux sources will appear between the highest Analog and lowest Digital channel number in the channel scan with Channel Up/Down. If the Aux sources will not be used, it is advisable to set them to 000 (Off) before doing 2-5-5 + Menu. After doing 2-5-5 +

Menu, the only way to turn the Aux sources off so they will not appear in the channel scan, is to go to the Channel Bank menus and select ‘Normal Delete’.

Refer to Installer menu items: 34, 35, 38, 39 and 87.

P A G E 2 4

CHANNEL PREVIEW - BANK 1

CH 011-001 NORMAL-ADDED

Enter -> Change

CC ->VCHIP Menu Ch. Preview -> Exit

Channel Bank Setup Menu

MUTE POWER

BANK

CH

PREVIEW GUIDE

SAP

INFO CC

CH

VOL

OK

CH

VOL

FLASHBK

TIMER MENU ALARM

ADJ

ADJ

ADJ

ADJ

BED1

BED2

3140OSKZ003AR6

Use to access Ch Preview Menu

206-4071

Channel Banks Setup Installer Remote Control Key Functions

Channel Banks Setup Remote Control Key Functions

CHANNEL PREVIEW - BANK 1

CH 011-001 NORMAL-ADDED

Enter -> Change

CC ->VCHIP Menu Ch. Preview -> Exit

Channel Bank Setup Menu

MUTE

POWER

BANK

CH

PREVIEW GUIDE

SAP

INFO CC

CH

VOL

OK

CH

VOL

After doing 2-5-5 + Menu, select a channel bank with the input/source or Banks button. After desired bank is selected, press Ch Preview to display the Channel Banks editing menu.

Shows currently selected Channel Bank.

Shows currently selected Channel.

Shows channel status in selected bank.

In Channel Banks menu, use the Left-Right arrows to select:

Normal-Added Channel will appear in channel scan.

Normal-Deleted Channel will not appear in channel scan.

Blank-Added Channel will appear in all channel banks, video will be black, no picture.

Blank-Deleted Channel will be blanked in all channel banks.

Bank

Selects channel banks 1-2-3-4.

Ch Preview

Selects channel banks setup menu.

Exits menu.

Channel Up

Selects next higher channel number.

OK (Enter)

Tunes in deleted channels in scan.

Channel Down

Selects next lower channel number.

FLASHBK

TIMER MENU ALARM

ADJ

ADJ

ADJ ADJ

BED1

BED2

3140OSKZ003AR6

206-4071

Typical Installer Remote Control

Up/Down Left/Right ADJ Arrows

Up-Down Tune to added channels in menu.

Left-Right Choose menu options.

Note: Pressing CC Displays V-Chip menu.

P A G E 2 5

Channel Banks Setup

Use the Channel Banks to format the channel lineup programming package options for the end user

Each channel bank is capable of storing broadcast digital and analog channels

Figure 1. Typical channel banks after running Auto Tuning

1

2

3

4

N

K

B

A

Purpose

1 2

A

A

A

A

3 4 5

A

A

A

A

6 7

A

A

A

A

8 9

A

A

A

A

A = Active - - Channel was found durin g AU TO TUNING

Chann el Number

10 1 1 12 13 14 1 5 16 17 18 19 20 21 22 2 3 24 2

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

5

A

A

A

A

Figure 2. Typical channel banks after running Auto Tuning, and customizing with Add/Del/Blnk

1

2

3

4

N

K

B

A

Purpose

Basic

Extend

All CTV

Other

A = Active

BC

BC

BC

BC

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

Channel Number

1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 5 16 1 7 18 19 20 21 22 23 24 2

A

A

A

A

Chann el was found durin g AU TO TUNING

D

A

A

A

D

D

D

A

D

A

A

A

D

D

D

A

D

A

A

A

D

A

A

A

D

A

A

A

D

D

A

A

D

D

D

A

D

D

A

A

D

D

A

A

5

BC = Blanked Channel Chann el was blanked using BLANK chann el option (ADD/DEL/BLNK).

Adding / Deleting / Blanking Channels

It is best to do ADD / DEL customizing before doing “BLANK.”

Auto Tuning (channel search) enters the same channel numbers in channel banks 1, 2, 3 and 4. Auto Tuning removes any channels previously customized with ADD / DEL / BLANK. The channels found in the channel search on your antenna / cable will be included, and any channels previously found but not currently available will not be included. ADD and DEL (not BLANK) can be used independently for channel banks 1, 2, 3 and 4. (If a channel is not found in the channel search, it can be added see the Channel Menu Manual Tuning option.)

Notes: A channel blanked, is blanked in all channel banks.

Selecting Deleted Channels

To tune to a Normal Delete channel: Select a Channel Bank where the channel is added. Or, direct enter the channel number then go to the bank where the channel is set as ‘Normal

Delete’ and reconfigure the channel status.

Note: Ch Override must be set to 001 to allow access to the channel scan.

Channel allocations in tuning bands:

• Broadcast and Broadcast Digital: 2 - 69

• CABLE - CATV, HRC or ICC: 1 - 125

Inactive TV Setup for Channel Bank 4

To create an inactive TV display on Channel Bank 4, select

Normal Delete for every channel in Bank 4. When Bank 4 is selected with the bank button on installer remote, the Inactive

TV, call attendant will be shown on the TV screen. The TV will turn itself off afterward. This will prompt the patient to arrange for an available programming package on Banks 1, 2 or 3.

P A G E 2 6

206-4071

Reference: Channel Banks Worksheet

Use the Channel Banks worksheet provided below to plan your program packages. Photocopy additional worksheet as needed.

1

2

3

4

B

A

N

K

Purpose

1

2

3

4

N

K

B

A

Purpose

1

2

3

4

N

K

B

A

Purpose

PLAN YOUR CHANNEL BANKS BY FILLING IN THESE CHARTS (or use photocopies)

1

2

3

4

B

A

N

K

1

2

3

4

B

A

N

K

Purpose

Purpose

Channel Number

1 2 3 4 5 6 7 8 9 10 11 1 2 13 14 15 16 17 18 19 2 0 21 22 23 24 2

Chann el Number

26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49

5

50

Chann el Number

51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74

76 77 78

Channel Number

79 80 81 82 83 84 85 86 87 88 89 90 91

Channel Number

92 93 94 95 96 97 98

75

99 100

101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125

206-4071

Date _____________ Installer _____________________________________ Page ___ of ____

Location ______________________________________________________________________

P A G E 2 7

Upgrading TV Software with USB Memory Card

.....

HDMI/DVI IN

..........

USB IN

SERVICE ONLY

UPDATE

RS-232C IN

RESET

......

SERVICE ONLY

....

R-AUDIO-L

(MONO)

VIDEO

RGB IN (PC)

.....

PILLOW

SPEAKER

NORMAL

SPEAKER

PILLOW

SPEAKER

On USB Memory Card

Assure that memory card has been formatted with

FAT format.

Y

P

B

VIDEO

P

R

L

AUDIO

R

AUDIO IN

(RGB / DVI)

REMOTE

CONTROL OUT

SPEAKER OUT

8

TV Rear Connections Panel

POWER

TV

PICTURE SOUND SAP

INPUT

RATIO

Upgrading TV Software

1

4

7

-

2

5

8

0

3

6

9

FLASHBK

VOL

TIMER

CC

MUTE

CH

ADJUST MENU RETURN

Upgrade TV Software

Select a type of sofware to be downloaded:

Upgrade TV Software

Upgrade PTC Software

Teach To TV

ENTER

Teach To TV

The following software files are found in the memory card.

Select the file you want to download to this TV.

Or, Press EXIT to cancel the upgrade.

Software File List in USB Memory

32LG30_UA_ 128.TLL

32LG30_UA_ 126.TLL

1. Plug USB Memory Card into USB In port on TV.

2. Menu should appear, if not press the Menu key.

3. Use Up/Down arrow keys to navigate through the upgrades. Select the upgrade that you want to install by highlighting it and pressing the

Enter key.

4. Copying progress will be shown. When upgrading is complete, the TV will turn Off.

Use Installer

Remote to Operate

Menus

Optional: Edit/Change File Name

If necessary, the file name can be edited or changed.

Learn From TV

Choose the name of the image file:

P A G E 2 8

32LG3DC_UA_ a a c c c .TLL

Notes

• Do not remove TV power cord or USB memory card while Learning, doing so might harm your

USB memory card.

• Do not remove TV power cord or USB memory card while Teaching, doing so may cause the TV to malfunction.

• You are allowed to edit the file name, however, a file with edited contents will not be recognized.

• Since clock data is copied into USB memory card as numeric data, the time difference between teaching and learning is not automatically adjusted. Either set the clock manually, or use

Auto Clock set on TV main menu.

206-4071

Master TV Profile Setup Learning/Teaching with USB Memory Card

206-4071

On Master TV, Create Profile and Learn

1. Set up all Master TV features on the menus and do a Channel Search. Add Channel and Aux

Labels etc. Tune in an analog channel.

2. Plug USB memory card into the USB In port on

Master TV.

3. Press Menu key to open Main menu. Highlight the Option icon.

4. Press the Left arrow key once, the Option icon on left side of menu will be highlighted.

5. Press number key ‘7’ a total of 7 times.

Upgrade TV Software

Select a type of sofware to be downloaded:

Upgrade TV Software

Upgrade PTC Software

Teach To TV

Learn From TV

6. Key in password* used to enter Installer Menu.

7. Using Up/Down arrow key, highlight “Learn

Current Profile’, then press Enter.

8. To identify the profile from others, you can change the last 5 digits. Key in a custom file name, then press the Enter key.

9. The Learning status will be shown on progress bar. As soon as learning the current profile is complete, a message will appear on screen indicating the learning process is done.

10. Remove the USB memory card.

Learn From TV

Learning current profile from master TV:

20%

Do not unplug until restart automatically

* See Installer Menu pages.

On Target TV, Teach Master TV Profile

1. Plug USB memory card with Master TV Profile setup into Target TV USB In port.

2. Press Menu key to open Main menu and then highlight the Option Menu icon.

3. Press the Left arrow key once, this will highlight the Option icon on left side of menu.

4. Press number key ‘7’, a total of 7 times.

5. Using the Up/Down arrow key, select ‘Teach New

Profile’, then press Enter key.

6. Use Up/Down arrow keys to navigate through profiles. Select the profile that you want to install by highlighting it and pressing the Enter key.

7. Teaching progress will be shown on the progress bar. As soon as teaching is done, a message will appear indicating that the teaching process has been completed.

Teach Current Profile

Teaching the selected profile to the TV:

20%

Do not unplug until restart automatically!

P A G E 2 9

TLL-1100A Clone Connections / Learning and Teaching Setups

Connections for the TLL-1100A Clone Programmer to Learn the Master TV Setup

On Master TV

Set up all Master TV features on the menus and do a Channel

Search. Add Channel and Aux labels etc. Tune in an analog channel. Insert MPI cable into TV

MPI port.

On TLL-1100A

1. Turn On the TLL-1100A.

2. Use the Mode button to select

Clone Mode.

3. Use the Left/Right arrow to select the CBank (1 - 8) to store the master TV setup in.

4. Plug the other end of the MPI cable into the MPI port on the bottom of the TLL.

5. With the Installer remote control, select item 1 on TLL menu.

6. Press Enter, to transfer the

Master TV setup into CBankX on the TLL. The TLL will copy the master TV setup.

7. When learning is done, disconnect MPI cable from Master TV.

On Target TV

1. Connect MPI cable from the TLL to the MPI port on the Target

TV. Assure that the correct

CBank(X) is selected on TLL.

2. With the Installer remote control, select item 2 to Teach the target TV the master TV setup.

3. Press Enter to begin teaching.

4. When Teaching is done, disconnect MPI cable and power the

TV Off. Unplug TV power cord.

5. Reconnect TV power cord.

Power the TV On and the master TV setup should be resident on the target TV.

CLONE SELECTION MENU

Selected Bank: CBank X Saved

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

CLONE CLOCK = 00:00

TV CLOCK = 00:00

THE CLONE IS VERSION V2.2.2

-To change menu items, Press

channel keys or digits.

-To execute item, Press ENTER.

TV Link

Loader-Demo

TLL1100A

Ready

MODE

MENU

ENTER

RECEIVE SEND

TLL1100A

Antenna

(or CATV)

M.P.I. Learning Setup

M.P.I. Teaching Setup

Antenna

(or CATV)

TV Link

Loader-Demo

TLL1100A

Ready

MODE MENU

ENTER

RECEIVE SEND

TLL1100A

CLONE SELECTION MENU

Selected Bank: CBank X Saved

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

CLONE CLOCK = 00:00

TV CLOCK = 00:00

THE CLONE IS VERSION V2.2.2

-To change menu items, Press

channel keys or digits.

-To execute item, Press ENTER.

Warning: Do not use the TLL-1100A while any PPV card is installed or clone programmer device will be damaged.

Notes: It is assumed that the TV is connected to a signal source, the TV source selected is Antenna (RF) In, the signal is from an Analog channel, not a digital channel, all equipment is connected to power and turned on and the TLL-1100A Cloner main menu is displayed on the TV screen, see above.

P A G E 3 0

206-4071

Cloning Connections/Learning Setup

Connections for the LT2002 Clone Programmer to Learn the TV Master TV Setup

Antenna or CATV

Ferrite Core

(TDK, ZCAT

2035-0930)

Connect cable to

TV MPI Jack and follow on screen instructions

Status

Indicator

MPI

Color

• green battery ok

• red battery low

Reset

Blink pattern

• slow power on

no communications

• heartbeat power on

communications ok

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION

THE TV IS VERSION

THE SW IS REVISION

XX

XX

XX

Warning: Do not use

LT2002 while any PPV card is installed in TV or clone programmer device will be damaged.

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

®

QuickSet II Programmer

LT2002

ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS USA

Clone Programmer

Master TV

Notes: It is assumed that the TV is connected to a signal source, the source selected is Antenna (RF) In, the signal is from an

Analog channel, not a digital channel, all equipment is connected to power and turned on and the LT2002 Clone Programmer main menu (THE CLONE HAS CONTROL OF THE TV) menu is displayed on the TV screen, see above and next page.

Before you begin cloning...

• The Master TV should be connected to a good, stable signal from an over-the-air antenna or cable service Analog channel and connected to power. (See above.)

• Teaching and Learning is only possible between identical model TV/STBs. (However, the LT2002 Clone programmer can store up to 3 different ‘master’ setups.)

WARNING: Copying a blank or incorrect memory into a TV, STB or other device will cause the TV, STB or other device to operate erratically or become inoperable.

• Use an Installer’s remote to operate Learning and Teaching menus.

• Make sure that the batteries in the Clone programmer are fresh.

• If batteries are removed, the Clone Clock time will be lost.

• Decide if you want to set the time from the Clone programmer or copy the time to the Clone programmer; from a compatible TV which has had the clock set to the current time.

• Setting the time and transferring it to the Clone or other device is a separate procedure.

• Follow the connection diagram above to connect the Clone to a Master TV display panel. After learning is complete, to another identical TV display panel to “teach” it the master TV setup.

• See the Clone Troubleshooting section to resolve problems.

Turn to the next page to continue Cloning Setup.

206-4071

P A G E 3 1

Cloning Learning Setup

Learning the Master TV Setup

Instructions for the Clone Programmer to Learn the Master TV Setup

Use MPI Cable to Connect LT2002 Clone Programmer to

Master TV MPI Port

If there is a good connection, “THE CLONE HAS CONTROL OF TV” message will appear. Press any key on the Installer remote.

Learn Setup from Master TV

Press 1 to select the “LEARN FROM TV” option, then press ON/OFF,

POWER, or ENTER to go to the Memory Bank Selection Menu. Pick the

Memory ”Bank” you want to store the master TV’s setup in by pressing either Channel key repeatedly to choose Memory 1, 2 or 3. (If you choose a Memory “Bank” that has a master device’s setup programmed into it, that setup will be overwritten by the new master

TV’s setup.) Once the Clone memory bank is selected, press ON/OFF,

POWER, or ENTER. The Clone memory bank you have selected will be shown. Press ON/OFF or POWER to begin copying the master TV’s setup.

Set the Clock (Optional)

Set the time on a Master TV’s Clock. (If the time has already been copied from a TV into the Clone programmer, you can set a master

TV’s clock by copying the time from the Clone programmer.) The

Clone Programmer can copy the current time to both a master TV and to the Clone’s internal clock; accurate to within one minute. (Another reason that the Clone programmer should be equipped with fresh, high-quality alkaline batteries, is for it to keep the time as accurately as possible.)

Since the Clone Programmer’s time cannot be set directly, the current time needs to be copied from a Zenith/LG TV equipped with M.P.I.

input capability.

After the time is copied to the Clone programmer, the current time can then be transferred to another TV. (This can be a master TV, or another TV which has already had the features set up.)

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION

THE TV IS VERSION

THE SW IS REVISION

XX

XX

XX

CLONE CLOCK=

TV CLOCK=

XX:XX

XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

This menu should appear by itself after the

LT2002 is connected to the TV MPI port.

CLONE SELECTION MENU

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER

This menu should appear after any key is pressed on the Installer remote.

LT2002 Clone Programmer Communication Problems

• A slow flashing green light indicates there are communication problems between the TV and the LT2002 clone programmer. If this is the case, check for a damaged cable, poor contacts, or other connection troubles.

• If the status indicator is red, the programmer batteries are low and should be replaced. Install 4 high-quality alkaline

AA batteries.

P A G E 3 2

206-4071

Cloning Connections/Teaching Setup

Teaching the Master Setup to Another TV

Connections for the LT2002 to Teach another TV the Master Setup

Antenna or CATV Ferrite Core

(TDK, ZCAT

2035-0930)

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION

THE TV IS VERSION

THE SW IS REVISION

XX

XX

XX

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

Target TV

Teach Master TV’s Setup to the target TV

After learning is complete, remove the M.P.I. cable from the master TV and connect it to the target TV that you want to copy the master TV’s setup into. With “THE CLONE HAS

CONTROL OF TV” message displayed, press 2 or use either

Channel key to go to the “TEACH TO TV” option, press ON/OFF,

POWER, or ENTER. Select the LT2002 memory that the new setup is in. Press On/Off to transfer the new setup and other information to the new TV. Teaching usually takes 2-3 minutes.

After the “TEACHING COMPLETE” message is displayed, press any key to return to the Clone menu, then press ON/OFF,

POWER, or ENTER. If finished, detach M.P.I. cable from the target, newly-cloned TV.

Disconnect TV Power for 15 Seconds

Unplug the AC power cord of the newly-cloned TV from the power outlet for about 15 seconds to activate the newlycopied setup.

206-4071

Connect cable to

TV MPI Jack and follow on screen instructions

Status

Indicator

MPI

Reset

Color

• green battery ok

• red battery low

Blink pattern

• slow power on

no communications

• heartbeat power on

communications ok

®

QuickSet II Programmer

LT2002

ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS USA

Clone Programmer

CLONE SELECTION MENU

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER

This menu should appear after any key is pressed on the Installer remote.

TEACHING IN PROGRESS,

PLEASE WAIT

This display will appear during

Teaching function.

TEACHING COMPLETE

This display will appear after Teaching is complete.

P A G E 3 3

Installer Menu

Use the Installer’s Menu to set up or change operational settings.

See more detailed descriptions of the Installer menu items on the following pages...

SCAN MODE

STRT CH IN SM

SLEEP TIMER

EN TIMER

ALARM

FEATURE LEVEL

V-CHIP

MAX BLK HRS

CAPTION LOCK

FUNCTION PRE.

HOSPITAL MODE

CH. OVERIDE

OLD OCV

Function

INSTALLER SEQ

POWER MANAGE

AC ON

BAND/AFC

STRT CHANNEL

CHAN LOCK

STRT VOLUME

MIN VOLUME

MAX VOLUME

MUTE DISABLE

KEY DEFEAT

IR BANKS EN.

022

023

025

027

028

029

013

014

015

016

017

020

021

Menu Item

000

001

002

003

009

010

011

012

004

005

007

008

Accessing the Installer’s Menu

Make sure TV is on. Installer’s menu items can be accessed by using an installer’s remote control. Just press MENU repeatedly until the TV seems to stop responding, then press 9,

8, 7, 6, and ENTER to access the Installer’s menu. To remove the Installer’s menu, press

ENTER again. Any changes you make will be stored in nonvolatile memory. (The menu also

disappears automatically.)

The Installer’s menu opens with item 000 INSTALLER SEQ 000. Use the Up/Down arrow keys to sequence through the available menu items. Or, access an item directly by keying in the line number, then pressing MENU. For example, to access the Sleep Timer option which is item 015, press 0-1-5, then MENU. To change a setting, use the Left/Right arrow keys. Or, enter a value directly.

Using the Installer’s Menu

Items 000 ~ 118 are immediately accessible only upon entering the Installer’s Menu.

Their numbers, descriptions, ranges, factory default settings, and a place for listing any changes made on-site are given below and on the following pages.

Installer Menu Items 000 through 30

0 ~ 99

0 / 1

0 ~ 3

0 ~ 2

0 / 1

0 / 1

0 / 1

0 / 1

0 / 1

0 / 1

0 / 1

0 / 1

0 / 1

Value Range

0 ~ 3

0 ~ 7

0 / 1

0 ~ 3

0 ~ 127, 255

0 / 1

0 ~ 63, 255

0 ~ 63

0 ~ 63

0 / 1

0 / 1

0 / 1

1

0

12

0

1

2

1

1

1

1

1

1

0

Default Value

0

0

0

1

63

0

1

0

255

0

255

0

HOSPITAL PTC INSTALLER MENU

UPN 000-000-000-000 FPGA E0F1

PTC V1.00.000

CPU V3.06.00

Typical Installer Menu

Brief Description of Function and Comments

Leave default set to 0.

Sets number of hours of no activity before auto shut Off.

Set to 1 to enable auto turn On at power up.

Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC

Channel at turn-on (Set to 255 to tune in last channel before power Off).

If set to 1, cannot tune from current channel.

Sets Volume level at TV turn-on (Set 255 to retain last volume level).

Sets minimum allowable volume setting.

Sets maximum allowable volume setting.

Set to 1 to disable mute function.

Set to 1 to disable menu navigation keys on TV.

Set to 1: enables TV to respond to IR code

Typically used for Hospitals: puts On-Off in Ch Up/Down sequence.

Set to 1 to put TV on/off below start channel number.

Set to 1 to enable Sleep Timer.

Set to 1 to enable On/Off Timers.

Set to 1 to enable Alarm.

Zen 1 Leave default set 1 (1 Zen 1)

Set to 1 to enable V-Chip functions.

Sets the number of V-Chip (Parental Control) blocking hours.

Set to 1 to retain caption setting at power Off.

Controls channel preview in Pay-Per-View function

Leave default set to 2.

If set to 0, limits direct access to favorite channels.

Set to 1 to change M.P.I. operation to OCV.

000

P A G E 3 4

206-4071

Installer Menu

Installer Menu Items 031 through 118

REVERT CH

QUICK SHUTOFF

UPN MSB

UPN MSB-1

UPN MSB-2

UPN LSB

CHKSM ERROR

HANDSHK TIME

PERMANENT BLK

REAR RGB EN.

EN NOISE MUTE

KEY LOCK

SAP MENU EN

DEF. ASP. RATIO

BACK LIGHTING

ATSC BAND

ATSC TUNE MODE

START MINOR CH

ASP RATIO LOCK

VIDEO MUTE EN

FACT DEFAULT

POWER SAVING

Function

ACK MASK

POLL RATE

TIMING PULSE

CAMPORT EN

COMPPORT EN.

YPrPb EN.

REAR AUX EN

AUTO CAMPORT

STRT AUX SRCE

AUX STATUS

DIS. CH-TIME M.

EN. CH-T COL.

FOR. CH-TIME

BCK. CH-TIME

CH NOT AVBLE

082

083

084

087

088

090

` 094

075

077

078

079

080

081

096

099

102

103

104

106

116

117

118

Menu Item

030

031

032

034

035

038

039

040

046

047

053

069

070

071

073

0 / 1

0 ~ 17

0 ~ 255

0 ~ 255

0 ~ 255

0 ~ 255

0 / 1

0 ~ 5

0 / 1

0, 2, 18

0 / 1

0 / 1

0 / 1

0, 2, 4, 5

1 ~ 100

101 ~ 200

0 ~ 4

0 / 1

0 ~ 255

0 / 1

0 / 1

0 / 1

0 / 1

Value Range Default Value

0 / 1 0

20 ~ 169

186 ~ 227

94

207

0 / 1

0 / 2

0 / 1

0 / 1

0 / 1

0 ~ 6

0 / 1

0 / 1

0 / 1

0 ~ 7

0 ~ 7

0 / 1

0

1

2

2

0

1

6

0

1

1

1

1

1

0

1

0

2

0

5

0

0

255

255

255

255

2

200

0

0

0

0

1

4

1

Brief Description of Function and Comments

If set to 1, changes M.P.I. for some OCV boxes.

Selects poll rate for M.P.I.

Sets baud rate for M.P.I.

Set to 1 to enable Video 2 input.

Set to 0 to disable HDMI 1. Set to 1 for DTV, set to 2 for PC.

Set to 1 to enable display panel Component Video 1 input jacks.

Set to 1 to enable display panel Video 1 input jack.

Set to 1 to automatically switch to Camport. If set to 1, STRT AUX SRCE cannot be set to 2.

Sets the starting AUX source.

Set to 1 for M.P.I. AUX source to be reported as a channel number instead of Channel 0.

Set to 1 to disable Channel-Time display.

Set to 1 to enable custom color for the Channel-Time display.

Chooses custom foreground color for the Channel-Time display.

Chooses custom background color for the Channel-Time display.

If set to 1 and channel override is 0, “NOT AVAILABLE” message is displayed when directly accessing a channel not in the favorite channel list.

If set to 1 and loss of M.P.I. communication occurs, TV tunes to Start Channel.

Allows TV timed power off press and hold setup with pillow speaker channel button.

User programmable number, most significant byte.

User programmable number, most significant byte - 1.

User programmable number, most significant byte - 2.

User programmable number, least significant byte.

Enforces rigid M.P.I. checksum.

Relaxes M.P.I. timing to be compatible with PC based Windows-controlled systems.

Removes block hours setting for Parental Control and makes block permanent.

Set to 0 to disable RGB1. Set to 2 to enable for RGB PC. Set to 18 for Auto detect configure.

If set to 1, mutes audio if no signal is present.

Set to 1 to disable front keyboard. Set to 1 to enable front keyboard functionality.

Set to 0 to disable feature on Function menu. Set to 1 to enable feature on Function menu.

Sets default aspect ratio at power up. See detailed descriptions and item 106.

Sets the brilliance of the TV picture backlighting.

Settings above 100 control dynamic back lighting and disable power saving mode..

Selects ATSC band.

Default 01 for physical channel scan. Set to 0 for Virtual Channel scan.

Selects Minor start channel. Set 0 for NTSC. Not 0, sets Minor channel number.

To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on power cycle.

Set to 0 for normal, set to 1 for Blank.

0=Normal. 1=Loads presets of all above settings.

Set to 0 to disable power saving mode.

206-4071

P A G E 3 5

Installer Menu

Detailed Descriptions of Installer Menu Items

000 - INSTALLER SEQUENCE

Specifies entry sequence to the Installer Menu.

0 = 9876 1 = 4321

2 = 1478 3 = 3698

Generally, this feature is used in connection with START CHANNEL

(Installer item 004) where the start channel may, for example, be set to 3 or 4. If the start channel is 3, then the TV will remain locked on

Channel 3.

001 - POWER MANAGE (Power Management)

Determines hours of no activity before automatic shutoff. The POWER

MANAGE function is for saving energy. If set to 0, Power Manage is Off.

Settings range from 0 ~ 7, with 1 ~ 7 representing the hours that the unit will remain On, unless there has been activity from either the control panel or remote control.

NOTE: For Items 007, 008 and 009

For legacy reasons, the scale used is 0 - 63. The PTC software will translate this to the 0 - 100 scale used by the TV.

To translate a TV volume level to the installer menu value, use the following formula:

002 - AC ON (AC Power Switchable)

If set to 1, allows the TV to turn On just by applying AC power.

Pressing the On button is not necessary. This is desirable if the TV is plugged into a cable box or a power outlet controlled by a wall switch.

Use ADJ Left/Right arrow to choose 0 or 1 where 0 is the default is

Off, and 1 is On.

NOTE: If set to 1 (On), the TV does not respond to On/Off commands from either the remote or the display control panel, and the SLEEP

TIMER is also nonfunctional.

003 - BAND/AFC (Band/Automatic Frequency Control)

There are 4 possible settings for this option:

Installer Value = TV Value x 63

100

Enter only the whole number (disregard fractions).

007 - STRT VOLUME (Start Volume)

This function allows the Installer to determine the initial volume level setting when the TV is turned On. This feature is useful for an in-house information channel, since the TV would always select that volume level when it is turned On. The range of values are 0 - 63, 255. If 255 is selected, the current volume level will be retained in memory when the TV is turned Off; at turn On, the volume level will be automatically set at the previous or last level.

0 = Broadcast

2 = HRC

1 = CATV

3 = IRC

If some channels were not found by Auto Tuning (Channel Search), select the appropriate Band setting here and add the channels using the Channel Edit option in the Channel Menu.

004 - STRT CHANNEL (Start Channel)

If active, this function allows you to determine the initial channel number when the TV is turned On. This feature is useful for an inhouse information channel, since the TV would always select that channel when it is turned On. Setting this to 255 causes the last channel viewed when the TV was turned Off, to be the tuned to channel when the TV is turned On again. Note: For a digital Start Channel, always remember to set item 104 to the Minor Start Channel number.

255 = Last channel

126 Map to Channel 3.

1 ~ 125 = Ch X 0 = Aux

127 Map to Channel 4.

008 - MIN VOLUME (Minimum Volume)

This function determines the minimum volume level allowable with the

VOLUME (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The value range is from 0 to 63

— change values with ADJ Left/Right arrow. The factory default is 0, which provides the full range of volume control, if item 009 MAX VOL-

UME is also set to 63. It may be best to set the same value on every

TV.

NOTE: The minimum volume level cannot have a value setting higher than the MAX VOLUME level (described below).

009 - MAX VOLUME (Maximum Volume)

This function determines the maximum volume level allowable with the

VOLUME (VOL) Up/Down controls. In this way, for example, someone can not set the volume level high enough to disturb others. The value range is 0 to 63, with 63 as the default, which gives the user the full range of volume control, if item 008 MIN VOLUME is also set at 0.

Change values with ADJ Left/Right arrow keys. It may be best to set the same value on every TV.

NOTE: The maximum volume level cannot have a value setting lower than the MIN VOLUME level (described previously).

005 - CHAN LOCK (Channel Lock)

CHAN LOCK is ideal if the system must always be on the same channel.

Changing channels with Channel Up/Down or keypad numbers is impossible. Channel Lock is inactive if set to 0 (default).

010 - MUTE DISABLE

Enables or disables sound mute function. If set to 1, sound cannot be muted. If set to 0, sound can be muted.

P A G E 3 6

206-4071

Installer Menu

011 - KEY DEFEAT (Keyboard Defeat)

If set to 1, key defeat prevents the end user from accessing the onscreen menus with the TV front panel—MENU, SELECT, and Left / Right arrow keys do not function. If set to 0, those keys do function. NOTE:

The menus can always be accessed by pressing MENU on the remote.

012 - IR BANKS EN (IR Banks Enable)

For direct access to a particular Channel Bank. When enabled, installer can access a channel bank by inputting the IR code for the bank.

013 - SCAN MODE (Functional after 2-5-5+Menu setup transfer)

Allows variation in setting the TV On/Off with Channel UP/DOWN. You may opt for TV channels only; TV channels + Off/ON; with these settings for Scan Mode:

SCAN MODE Characteristics

0

1

Channel up/down keys change channels only.

Channel down below the lowest channel

(or channel up higher than the highest) and TV turns off.

014 - STRT CH IN SM

(Start Channel in Scan Mode) If set to 1, installs TV On/Off event below the start channel at TV turn On. If set to 1, the user can select channels with either Channel Up/Down or by direct keypad entry. If set to 0, only those channels that are entered for scanning can be selected.

022 - MAX BLK HRS (Maximum Block Hours)

Sets hours from 0 to 99 for the maximum V-Chip (Parental Control) block hours. Default setting is for 12 blocking hours.

023 - CAPTION LOCK

Set to 1 to restore previous caption On/Off state after turn Off. If set to 0, captions are always Off at turn On.

025 - FUNCTION PRE (Function Preview)

Set to 0 to suppress CHANNEL PREVIEW from the FUNCTION menu with some Pay-Per-View systems.

027 - HOSPITAL MODE

The default is 2 (which favors most hospitals). With this setting two things are affected: Channel Banks 1, 2 and 3 are accessible, while

Bank 4 can be made inactive by removing all the channels from

Channel Bank 4. Then, if Channel Bank 4 is selected when the TV is turned on, the TV screen will show “Inactive TV”. The Channel Bank 4 setup allows the hospital to present TV viewing options to the patient.

The patient can select programming options available in either Bank 1,

2 or 3. Channel Banks are available in all hospital modes 1 an 2.

• The IR code that will control the TV depends on Item 20-I Feature

Level setting.

Hosp. Mode = 0 Hospital Mode disabled.

Hosp. Mode = 1 Zenith P.L. IR Code (Bed 1)

Hosp. Mode = 2 Zenith IR Code (Bed 2)

015 - SLEEP TIMER

If set to 1, the SLEEP TIMER feature may be used. If set to 0, the

Sleep Timer is not available.

028 - CH. OVERIDE (Channel Override)

If set to 1, the user can select channels with either Channel Up/Down or by direct number keypad entry. If set to 0, only those channels that are active in the TVs memory can be selected.

016 - EN TIMER (Enable On/Off Timers)

If set to 1, Timer function is available to end user and enabled continuously. Set to 0 to disable On/Off Timers. (Clock must be set in order to use Timers.)

017 - ALARM *

Gives the installer the option of making the Alarm function available to the end user. If set to 1, Alarm function is available to end user. Set to 0 to disable the Alarm function.

NOTE: Clock must be set before the Alarm function will work.

029 - OLD OCV (On Command Video TM )

Set to 1 for operation with systems from On Command Corporation.

030 - ACK MASK

M.P.I. Communication Parameter. Leave at default setting unless changed by Pay-Per-View provider. When set to 1, changes M.P.I. for some OCV boxes.

020 - FEATURE LEVEL

Installer should leave item 20 FEATURE LEVEL set to 1 (default).

Default set to ZEN 1 for Zenith IR codes remote control operation. Set

O, P LBL for Zenith Private Label IR remote control operation. Warning:

Do not set to “0” or remote will not control TV.

031 - POLL RATE

M.P.I. Communication Parameter. Selects Poll Rate for M.P.I. Leave at default setting unless changed by Pay-Per-View provider. Step size of

16 ms.

032 - TIMING PULSE

M.P.I. Communication Parameter. Leave at default setting unless changed by Pay-Per-View provider. Sets baud rate. Step size of 4.3 uS.

021 - V-CHIP (Parental Control)

Set to 1 to activate V-Chip (Parental Control); have it available to end user to filter and control or otherwise restrict programming content that can appear. Set to 0 to turn V-Chip feature Off, not available to end user; no programming restrictions can be set.

034 - CAMPORT EN. (Camera Port Enable)

Set to 1 to enable Video 2 input on display panel. If set to 0, Video 2 input on display panel is not functional.

NOTE: S-Video overrides Video jack.

* Only affects Function Menu if enabled by some PPV providers.

206-4071-D

P A G E 3 7

Installer Menu

Detailed Descriptions of Installer Menu Items

035 - COMPPORT EN. (HDMI 1 Port Enable)

Enable/disables TV display panel HDMI 1 input jack.

Set to 0 to disable, set to 1 to enable.

038 - YPrPb EN. (Rear Component Video Enable)

Set to 1 to enable display panel rear Component Video input jacks.

Set to 0 to disable display panel rear Component Video input jacks.

071 - BCK. CH-TIME (Text Display Background Color)

Set according to Color Chart.

0 = Black

1 = Blue

3 = Cyan

4 = Red

6 = Yellow

7 = White

2 = Green 5 = Violet

Notes: Applies only to ‘Channel Not Available’ message if item 073 is set to 1, enabled. If foreground color and background color are the same, background will be transparent.

039 - REAR AUX EN. (Rear Aux Enable)

Set to 1 to enable display panel rear AUX (Video 1) input.

Set to 0 to disable display panel rear AUX (Video 1) input.

Note: S-Video overrides Video.

073 - CH NOT AVBLE (Channel Not Available)

If set to 1 and item 028 CHANNEL OVERRIDE is set to 0, “NOT AVAIL-

ABLE” message is displayed when directly accessing a channel not in the channel scan list available in memory.

040 - AUTO CAMPORT

Set to 1 to automatically switch to camport when equipment is connected to front Video input.

Set to 0 to disable front Video automatic source selection.

If set to 1, STRT AUX SRCE cannot be set at 2.

If item 040 Auto Camport is set to 1:

1 = Video 1 3 = HDMI 1 6 = Component

4 = RGB

Note: Above is applicable only if all Aux sources are enabled.

075 - REVERT CH (Revert to Start Channel)

If set to 1 and loss of M.P.I. communication occurs, TV automatically tunes to the specified Start Channel.

046 - STRT AUX SRCE (Start Aux Source)

Sets the starting AUX source. At power up, TV will tune to starting Aux source if item 004 Start Channel is set to 0.

1 = Video 1

2 = Video 2

4 = RGB

3 = HDMI 1

255 = Last Aux

6 = Component

077 - QUICK SHUTOFF

Allows TV power Off event to be controlled by the Remote Control, TV

Front Panel and Pillow Speaker Channel Up/Down buttons. End user would push and hold channel button down for time required to have

TV turn Off. Setting 0 = disabled. Value Range 0 - 17, each number represents 1/2 second. For example, if set to 4, TV would turn Off if end user held any channel button down for 2 seconds.

078 - UPN MSB (UPN Most Significant Byte)

User programmable number, most significant byte readable by M.P.I.

command. Note: Not linked to serial number.

047 - AUX STATUS

Set to 1 for M.P.I. AUX source to be reported as a channel number instead of channel 0. Set to 0 to disable AUX identification change.

Controls M.P.I. status channel response for AUX inputs.

079 - UPN MSB-1 (UPN Most Significant Byte-1)

User programmable number, most significant byte-1 readable by M.P.I.

command. Not linked to serial number.

053 - DIS. CH-TIME (Disable Channel-Time)

Set to 1 to disable the Channel-Time display, Channel-Time display will not appear. Set to 0 to enable the Channel-Time display.

080 - UPN MSB-2 (UPN Most Significant Byte-2)

User programmable number, most significant byte-2 readable by M.P.I.

command. Not linked to serial number.

069 - EN. CH-T COL. (Enable Text Custom Color)

Set to 1 to enable custom color for the Channel-Time display.

Set to 0 to disable custom color for the Channel-Time display.

081 - UPN LSB (UPN Least Significant Byte)

User programmable number, least significant byte readable by M.P.I.

command. Not linked to serial number.

070 - FOR. CH-TIME (Text Display Foreground Color)

Set according to Color Chart.

0 = Black

1 = Blue

3 = Cyan

4 = Red

6 = Yellow

7 = White

2 = Green 5 = Violet

Notes: Applies only to ‘Channel Not Available’ message if item 073 is set to 1, enabled. If foreground color and background color are the same, background will be transparent.

082 - CHKSM ERROR (Checksum Error)

Enforces rigid M.P.I. checksum validation.

Set to 1 for validation.

Set to 0 to disable (does not check checksum on M.P.I. async port).

SPI is always checked.

083 - HANDSHK TIME (Handshake Time)

Adds an additional delay to the handshake time which is 64 msec,

P A G E 3 8

206-4071

Installer Menu

thus relaxing M.P.I. timing requirements to be compatible with PC based Windows controlled systems, range is 0 - 5.

(Timeout = 25.5MS + [25.5 MS* Handshake time]).

084 - PERMANENT BLK (Permanent Block)

Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function.

Set to 1 to install Parental Control restrictions permanently.

Set to 0 for user-specified hours control of blocking schemes.

087 - REAR RGB EN. (Rear RGB Enable)

Controls access to rear RGB input on TV.

Set to 0 to disable RGB input.

Set to 2 to enable for RGB PC input and automatically configure its input format every time TV is turned On.

Set to 18 to enable RGB PC input and to configure the input format one time only with AC power cord removal and reinsertion.

088 - EN NOISE MUTE (Enable Noise Mute)

If set to 1, audio mutes if no signal is present.

090 - KEY LOCK

If set to 1, front keyboard buttons Channel, Volume and Captions are disabled, Power button remains enabled. If set to 0, front keyboard

Channel, Volume, Captions and Power buttons are all enabled.

094 - SAP MENU EN (2nd Audio Program)

Set to 1 to enable SAP feature on Function menu, if Function menu is available.

Set to 0 to disable SAP feature on Function menu, if Function menu is available.

096 - DEF. ASP. RATIO (Default Aspect Ratio)

Selects default aspect ratio at power up, see settings below.

Note: Only applies if item 106 Aspect Ratio Lock is disabled, set to 0.

Set to 0 “Set By System”.

Set to 1 for 4:3.

Set to 2 for 16:9 (Factory Default).

Set to 4 for Zoom 1

Set to 5 for Zoom 2

099 - BACK LIGHTING

Sets the TV screen brightness at power up, see settings below.

Default setting is 100.

1 - 100 Static Backlighting.

(1 = Dimmest picture, 100 = Brightest picture.)

101 - 200 Dynamic Backlighting.

(101 = Dimmest picture, 200 = Brightest picture.) If settings are above

200, the TV automatically controls backlighting depending upon the picture level of the current program.

102 - ATSC BAND

Sets up TV to receive different types of incoming signals:

0=Broadcast, 1=CATV, 2=HRC, 3=IRC, 4=Same as NTSC.

103 - ATSC TUNE MODE

Sets ATSC tuning mode: Default set to 1 for Physical channel scan.

Set to 0 for Virtual Channel scan.

104 - START MINOR CHANNEL

Sets XX-XX digital minor sub start channel at power up: 0=NTSC. If not

0, number selected is the digital minor start channel number.

106 - ASP RATIO LOCK (Aspect Ratio Lock)

Set to 1 to retain previous aspect ratio with power Off.

Set to 0 to retain default aspect ratio with power Off. See item 96

Default Aspect Ratio above.

116 - VIDEO MUTE EN (Video Mute Enable)

Set to 0 for normal.

Set to 1 for blank.

117 - FACT DEFAULT (Factory Default)

Set to 0 for normal.

Set to 1 and press Enter to load presets for all of the Installer menu item settings.

WARNING: Setting this to 1 and pressing Enter will reload the factory defaults and clear the channel list including erasing any assigned Channel Icons and custom channel

Labels.

118 - POWER SAVING

Default is set to 1, power saving mode is enabled.

Set to 0 to disable power saving mode.

• Power Saving is only active when TV is in standby mode.

• Power Saving is not available in normal power on mode.

If Power Saving is enabled and TV is in Standby mode with External

card installed: TV can supply 12V (9.6 Watts) to External card and

Standby power consumption will be small.

If Power Saving is disabled and TV is in Standby mode with

External card installed: TV can supply 12V (12 Watts) to External card and Standby power consumption will be normal.

206-4071

P A G E 3 9

Reference: Detailed Information For Making A Master TV

IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING...

To set up a master TV you will need to know how to enter the TV Installer menu and make changes to the default values as required. If necessary, familiarize yourself with the TV Installer menu and how to make and save changes in the menu, before attempting to clone the TV Master setup.

You will also need an LG Installer remote control similar to the one shown in the front of this manual. The installer remote must have a “Source” button or its equivalent. The remote shown in this manual has a “INPUT” button -- this button serves the purpose of a Source button.

Finally, the TV’s clonable features need to be set up. This is a critical step. If the Master TV display panel’s clonable features like adding channel icons or channel labels, digital font closed caption options etc., are not correctly added, then the cloned

TVs will all have problems.

As the cloning procedure is being performed, specific steps need to be done at the indicated times to create a correct master TV setup and cloned target TVs. Be sure to do each task as indicated. If a procedure or step is left out or not performed completely, cloning may not work. At each step, pay attention to assure the TV screen shows the proper message when cloning. If the message indicated does not appear, there is a problem with that step and cloning may not be successful.

Cloning is only possible when the signal source is an Analog channel, not a digital channel.

Making a Master TV

Detailed Instructions

The following describes the procedure for preparing a Master TV for cloning and the procedure for adding Channel Icons and/or

Labels.

Note 1: Disconnect all Aux inputs. Under certain conditions,

Auto Tuning is disabled if there is an Aux input active.

Note 2: Under certain conditions, changes to the input mode of the RGB input will not take effect until the power is cycled (TV is turned Off and On). To avoid confusion, disconnect RGB input before entering the Installer menu.

1. Enter the TV installer menu. a. Reset the internal controller to factory default by accessing installer menu item 117 FACT DEFAULT, set it to 1 and press “ENTER”. The value will change back to 0 after the TV’s internal controller has been restored to factory default condition. This step will ensure that the TV channel memory will be the active channel list. Check the Status LED inside the

TV. If it is blinking rapidly, the TV channel map is in use. b. Within the Installer menu, set the Installer menu items to the configuration required of your institution. c. It is important to set the tuning band at this time, set

Installer menu item 03 BAND/AFC. Default is 001 CATV.

d. Set Installer menu item 28 – CH OVERIDE to 001 to allow access to Auto Tuning and Channel Edit options in the

Channel Menu. Exit the Installer menu.

2. Access the Master TV menus and set the clonable options on the menus to the desired configuration. Refer to the

Clonable Menu Features Chart in this manual.

3. Run Auto Tuning to find analog and digital channels.

4. Enter the Channel Edit menu and edit the channel lineup to include the Free-To-Guest Channels only.

5. Assign ICONs to the channels using the Channel Label Menu.

Note: You can add Channel ICONS typically network logos like ABC, NBC, PBS etc. in this step. Or, in Step 7, add

Channel ICONS or labels for channels without Icons.

6. Transfer the TV setup: Enter the TV installer menu. Press ‘2’,

‘5’, ‘5’, ‘MENU’ to start the transfer of the TV’s setup to the

TV internal controller. Once the transfer is complete, the system will exit the Installer menu. Check the Status LED inside the TV. It should be blinking slowly (1 blink per second). Note: The maximum number of active channels and

Aux sources that can be transferred is 140. Total channels numbering more than 140 will result in erratic TV operation.

7. Edit/Add Channel ICONs and Channel Labels as needed.

Enter Installer menu. With menu displayed, press 2-5-4 +

MENU. See the following page for detailed instructions:

- Editing/Adding Channel ICON and Labels on Master TV

- Changing a Channel’s ICON on Master TV

- Changing/Adding Channel Labels on Master TV

- Changing Source Labels on Master TV

8. Verify Master TV setup and feature configuration:

• Did you add Channel ICONS?

• Did you add Channel Labels?

• Did you add Source Labels?

• Did you adjust all TV menu options as required?

After verifying master setup, enter the TV Installer menu and set Installer menu item 28 CH OVERIDE to 000. Press ENTER to remove and exit the Installer menu.

P A G E 4 0

206-4071

Reference: Procedures for adding Channel Label Icons/Custom Channel Labels

(2-5-4 + MENU Mode)

Adding Channel Icons and Labels in the 2-5-4 + Menu Mode

Editing/Adding Channel ICONs and/or Labels

If there is no pre-assigned ICON, you can make a custom channel label of up to 7 characters to help in identifying the channel or network. At your option, channel labels can also be added in addition to a pre-assigned ICON. You may also add labels for the Aux input sources to clearly identify the devices that are connected to the Aux inputs.

(Icon)

XYZ

XYZ

1 2 3 4 5 6 7

Editing and adding the labels can only be done if there are channels entered into the TV’s channel map either by using the method described in item 6 (page 38), by cloning or by the use of the master remote control from the PPV provider.

Note: A blank letter space is available between ‘Z’ and ‘!’.

XYZ

NETWORK

(Label)

To Do Channel Editing/Labeling, proceed as follows

1. Enter TV Installer menu.

2. Once the installer menu appears, press ‘2’, ‘5’, ‘4’,

‘MENU’. This enters the channel label editing mode.

Add your channel icons and channel labels in this menu, see below. (You can do this more than once.)

3. To exit the menu when done press “MENU”.

Changing a Channel’s ICON on

Master TV

1. With Channel Up/Down, select the channel you want to change the

Icon for.

2. With the Right or Left ADJ arrow, select the letter ‘I’ on the channel

ID display.

3. With the Up or Down arrow, select the desired ICON you want to appear to identify the channel. (If you know the ICON number, enter the number followed by Enter /

Select.)

4. Proceed with Changing/Adding

Labels or go to the next channel.

Changing/Adding Channel Labels on Master TV

1. Channel Up/Down to select the desired channel.

2. Press the Right or Left ADJ arrow repeatedly until the numbers 1 to 7 show up. The number shows the position of the character that can be changed. Number 1 is the first character, number 2 the second character and so on.

3. With the Up or Down arrow, select the desired character.

4. Proceed to the next number position or use Channel Up/Down to go to the next channel.

Changing Source Labels on

Master TV

1. Press “INPUT” to select the desired

Aux input source; Video 1, Component,

S-Video etc.

2. Use the Up or Down arrows to select the desired character for space 0.

3. Press the Right or Left arrow repeatedly to select number spaces 0 to 9. The number shows the position of the character that can be changed.

4. Press “INPUT” for the next Aux source or proceed with Changing Icon or

Changing/Adding Labels.

Installer Remote Control Key Functions for Master TV Channel Editing/Labeling Menu

• CHANNEL Up/Down - Tunes in the next channel in scan.

• Left/Right Arrows - Select the item to change. If “I” is shown, the ICON can be changed. If a number is shown, it indicates the position of the character that can be changed.

• Up/Down Arrows - Select the ICON or the character to be displayed.

• 0 – 9 - Use to enter the index number of the ICON, if known.

• ENTER/SELECT - Changes the ICON after the number has been entered.

• INPUT - Changes the Aux input label. (“Source” on the remote shown in this manual is INPUT.)

• MENU - Exits the editing process.

206-4071

P A G E 4 1

Reference: Clonable Menu Features

Menu /Sub Menu Features

Channel Menu

Auto Tuning

Manual Tuning

Channel Edit

Channel Label

Clonable Menu Features

Option Menu

Language

Captions

Picture Menu

Picture Mode

Audio Menu

Auto Volume

Clear Voice

Installer Menu

Item Settings

Note: Some menu options will revert to their default settings after cloning.

Note: End user only has access to features that are available on End user pillow speaker, or remote control if provided by the institution.

Reference: Checking Software Version

Procedure for Checking Software Version

The software version of the TV may be checked by accessing the INSTALLER MENU.

To do this, press the MENU button repeatedly until the menu display ceases to respond to MENU key presses.

Then, press "9", "8", "7", "6", "ENTER/SELECT". Press Enter again to remove Installer menu.

HOSPITAL PTC INSTALLER MENU

000

UPN 000-000-000-000 FPGA E0F1

PTC V1.00.000

CPU V3.06.00

Typical Installer Menu

P A G E 4 2

206-4071

OPTION

Language

Caption

CHANNEL PICTURE

AUDIO

TIME OPTION LOCK

Move

:English

: Off

Enter

If Upgrade Menu Does Not Appear

1. Go to the Option Menu.

2. Highlight the Option Icon on the left side of menu.

3. Press the number 7 key 7 times (7-7-7-7-7-7-7) then press ENTER.

4. Upgrade Menu should appear.

USB Cloning Troubleshooting

206-4071

P A G E 4 3

TV Camport Auto Sense Operation

The CAMPORT Auto Sense function is enabled when:

1. Installer Menu Item 34, CAMPORT EN is set to 1 AND

2. Installer Menu Item 40, AUTO CAMPORT is enabled (1).

Selectable= Can be accessed with INPUT key, direct access, etc.

Auto Sense= Switches to this input when connector is inserted.

The camport (Front Video) has the highest priority and will override any commands including tuning to the Start Channel.

CAMPORT (Front Video) Functionality Control

Item 34 Item 40

CAMPORT EN AUTO CAMPORT

0 0

0 1

1

1

0

1

Front Video

Operation

Disabled

Disabled

Selectable

Auto Sense

CAMPORT Operation (Stand-Alone)

When Camport Auto Sense is enabled as above, the TV’s source will switch to the front video whenever a plug is inserted into any of the front panel video inputs (either composite Video or

S-Video).

When the plug is removed, the TV will switch back to the previous channel or input source that the TV was using before the plug was inserted. However, if any direct access to an RF channel or Aux channel is requested while the camport is active, then, when the camport plug is removed, the TV will switch to the last requested channel. Source changes using any Source

Keys (INPUT) are ignored. Channel Up, Channel Down and

Flashback Commands are not direct access tuning commands and they are also ignored.

Previous State Operation

Before Inserting While CAMPORT

CAMPORT

Aux or RF Channel

Is Active

None

Direct Access Aux or RF Channel

Aux or RF Channel Ch Up/Down,

Flashback and TV/AV Keys

State

Upon Removal

Of CAMPORT

Previous Aux or RF Channel

Last Requested

RF or Aux Channel

Previous Aux or RF Channel

CAMPORT Operation (PPV)

The operation will be similar to that of the Stand-Alone mode.

However, the PPV providers may send different commands to the TV for the same user commands. For instance, some providers will always send a direct tune command when it receives a channel up/down or a flashback command while other PPV providers will just send a key command.

Previous State Operation

Before Inserting While CAMPORT

CAMPORT

Aux or RF Channel

Is Active

None

Aux or RF Channel

Aux or RF Channel

Direct Access

Ch Up/Down,

Flashback and TV/AV Keys

State

Upon Removal

Of CAMPORT

Previous Aux or RF Channel

Last Requested RF or Aux Channel

Last Requested

Channel if PPV translates it to direct access tuning command. Otherwise, goes to Previous Aux or RF Channel

P A G E 4 4

206-4071

TV Aux Input Configuration

DIRECT ACCESS

Tuning

TV

OLD_OCV

=0

OLD_OCV=

1

Source Input Source Mode Number

ENABLE

Installer Menu

Labeling

MPI DATA

MPI DATA

STATUS TYPE

0x41 SOURCES

ENABLED (R/W)

DATA STATUS

TYPE 0xD2

CURRENT AV

SOURCE (R)

DATA

STATUS

TYPE 0X0D

START AUX

SOURCE

AUX SOURCE

ASSIGNMENT

(R)

Value Labeling Value Labeling

130

131

133

90

91

93

Video2 (Side) CV/SVIDEO

Video1 (Rear) CV/SVIDEO

HDMI1/DVI

DTV

PC

DTV

34

39

35

35

87

CAMPORT_EN 0x01

Video Front

(Camport)

REAR_AUX_EN 0x02

COMPPORT EN = 1 0x08

COMPPORT EN = 2 0x08

Rear Video

(Aux)

Front

Computer

Front

Computer

REAR RGB EN = 1 0x10

SVGA Rear

Computer

0

1

3

3

4

Video Front

(Camport)

0 (VIDE0)

Rear Video

(Aux)

Front

Computer

Front

Computer

0 (VIDE0)

0 (VIDE0)

2

(COMPUTER)

SVGA Rear

Computer

0 (VIDE0)

2

1

3

3

4

134 94 RGB

136 96 Component

PC 87

38

REAR RGB EN = 2 0x10

SVGA Rear

Computer

YPrPb EN 0x40

Y/UV

Component

4

6

SVGA Rear

Computer

2

(COMPUTER)

Rear

Y/PrPb

Component video

0 (VIDE0)

4

6

Power Savings Setup

Installer Item 118 Power Saving: set to 001, enabled (Default).

Installer Item 099 Backlighting: value set as shown below. (Default value is 200)

Item 099

Backlighting

(Static)

100

90

80

70

60

50

40

30

20

10

1

Picture Power

Lumin.

Consumption

217

202

188

172

157

128

124

109

95

78

64

(Watts)

122

114

109

102

95

89

82

75

69

62

56

Power

Savings

Rating

0 %

7 %

11 %

76 %

22 %

27 %

33 %

39 %

43 %

49 %

54 %

Note: Values are results of controlled experiments under laboratory conditions.

Item 099

Backlighting

(Dynamic)

200

190

180

170

160

150

140

130

120

110

101

Picture Power

Lumin.

Consumption

130

123

117

109

101

94

86

79

72

63

57

(Watts)

86

83

80

76

74

70

67

64

61

58

56

Power

Savings

Rating

30 %

32 %

34 %

38 %

39 %

43 %

45 %

48 %

50 %

52 %

54 %

206-4071

P A G E 4 5

Troubleshooting

Some quick and easy tips to resolving problems

Possible Cause(s) Symptoms

Power

No Power.

TV Picture

No Picture.

See troubleshooting flow chart.

Possible Solution(s)

• Display panel is turned off.

• Antenna/Cable not connected.

• Connections incorrect.

• M.P.I. not connected.

• Encrypted program.

• Wrong tuning band.

-Turn TV on.

-Power failure?

-Connect Antenna/Cable signal to TV.

-Check connections on TV.

-If applicable, connect M.P.I. cable to M.P.I. device.

-Try another channel.

-Adjust Installer menu settings.

Erratic Operation

Installer menu setup.

• Wrong Installer menu settings.

-Adjust Installer menu settings as required.

Remote Control

Remote doesn’t work.

• Remote not in TV mode.

• Not aimed at IR remote sensor.

-Use Mode key to select TV; puts remote into TV mode.

-Point remote at TV’s IR receiver on TV.

• Remote too far from IR sensor.

-Move remote closer to TV’s IR receiver or darken room.

• IR path to TV’s receiver obstructed. -Remove obstructions.

• Weak batteries.

• Wrong battery polarity.

• Too much light in room.

-Replace batteries.

-Check that “+” and “-” match in battery compartment.

-Dim room light.

• Wrong Installer remote control.

-Requires compatible Installer remote, contact your LG dealer.

Picture / Sound

Normal picture, poor or no sound.

• Audio muted.

• Broadcast problem.

• Pillow Speaker Switch setting.

-Press MUTE or use Volume Up key to increase sound level.

-Try a different channel.

-Check pillow speaker switch setting. If set to Normal, sound will be heard on TV speakers. If set to Pillow, sound will be heard on pillow speaker.

Software Problems

Cannot direct enter channel number or

“No Signal” appears.

Channel not included in channel scan in TV controller.

After 2-5-5 + MENU, only channels included in TV controller will appear.

If channel is available it can be added to channel scan. If it is not available, the ‘No Signal’ message appears on the TV screen.

Note: For other problems not caused by the TV, refer to other devices’ operating guides.

P A G E 4 6

206-4071

Reference: LT2002 Cloning Procedure Troubleshooting

Warning: Do not use LT2002 while any PPV card is installed in TV or clone programmer will be damaged.

Reset Clone After Static Shock

After replacing exhausted batteries, or if the programmer behaves strangely after a static shock, use a paper clip or similar instrument inserted through the small hole marked ”RESET” to activate the internal reset switch and restore normal operation. After a reset, check the real-time clock setting. It may be necessary to reset the Clone Programmer clock from a TV containing the correct time.

Note

The LT2002 programmer is designed to be used with TVs containing the 221-01006 and later processors. Use with earlier TV sets may give unpredictable results. Processors used before the

221-01006-04 have a limited screen display capability. They cannot display entire screens as shown in the quick setup instructions accompanying the LT2002 clone programmer. Use the printed menu illustrations on the quick setup sheet supplied with the Clone as an aid to making your programming choices. (Although the menus are not all displayed, the clone functions all operate normally.)

Clone Programmer Troubleshooting

Problem Possible Cause(s)

Clone Programmer

Clone copies Setup in less than 30 seconds

Remote does not operate clone.

LED does not blink.

• Not enough time to copy entire TV setup.

• Wrong Installer remote.

• M.P.I. cord not connected.

• TV not turned on.

• Weak batteries.

• Weak signal.

Clone menu hard to read.

No time set.

Clone not working.

Clone Scans Channels more than once.

• Time not available.

• Clone programmer problem.

• Clone should only scan channels once.

Possible Solution(s)

- Press Reset on clone programmer, redo teach/learn.

(Teach/Learn should take a minimum of 1 minute.)

- Only use an LG Installer remote to operate clone programmer with TV.

- Connect M.P.I. cord properly, assure good connection.

- TV must be powered On for clone to work.

- Install 4 fresh AA high-quality alkaline batteries.

- Connect TV to a reliable Analog channel signal source.

- Set time on a TV, copy time to Clone Programmer.

- Try a different LT2002 Clone programmer.

- Reset Clone Programmer.

- Retry cloning again.

Master and Other TVs

Cloning did not work.

• Procedure interrupted.

• Different TV models.

• Step(s) omitted or not performed.

Clone time disappeared.

• Batteries were removed.

- Wait until procedure complete message is displayed.

- Cloning is only possible with identical model TVs.

- Reread pages 7-8-9 to be sure all tasks were performed.

206-4071

- Batteries must remain installed to retain time settings.

New Setup not present.

• TV not reset.

- Disconnect newly-cloned unit from power for 5 seconds.

• After cloning operations are complete, just unplug the LT2002 from the TV.

• If the TV does not display a picture on the TV (blank screen) after a few seconds, just change channels.

P A G E 4 7

Channel Banks Setup Troubleshooting

CHANNEL PREVIEW - BANK 1

CH 011-001 NORMAL-ADDED

Enter -> Change

CC ->VCHIP Menu Ch. Preview -> Exit

Channel Banks Setup Menu

Problem Solution

Cannot change channel status in menu. Installer menu item 028 Ch Overide is set to 000.

Set Ch Overide to 001 to allow access for channel status change.

Channel Preview menu does not appear.

2-5-5+ Menu procedure was not performed.

Channel Banks setup menu will not be available until 2-5-5+ Menu procedure is done.

And, item 028 Ch Overide is set to 001 to allow access for channel status changes.

Channel is blanked in all channel banks.

Blanking a channel in one channel bank will make it blank in all channel banks.

Cannot tune in deleted channel on Ch Preview menu.

Select a channel bank where the deleted channel number is set to ‘Normal Added’.

Direct enter the deleted channel number. Change to the bank you want to activate the channel in. Select ‘Normal Added’ on the Ch Preview Channel Banks menu.

‘Inactive TV’ message appears and then TV turns off.

TV is set up to display ‘Inactive TV’ message if all channels are ‘Normal Delete’ from

Channel Bank 4. Select another channel bank (Bank 1, 2 or 3) which will return TV to normal operation.

Channel found in scan does not tune in Channel was deleted in currently selected channel bank. If banks were set up, premium with Channel Up/Down. channels may only be available on another channel bank.

Select the channel bank where the channel is set to ‘Normal Added’. Or, direct enter channel number then go to banks menu and select ‘Normal Added’.

If ‘Bank’ on Installer remote is pressed, Item 027 Hospital Mode in Installer menu is set to 0. Set back to default ‘2’ for

TV shows Aux sources selection menu.

Channel Banks to appear with Bank or Source key presses.

P A G E 4 8

206-4071

Troubleshooting Flow Chart

Controller

Quick

Check

Is

'STATUS'

LED on

Analog Board

Blinking

?

Yes

No

Is

TV

Connected to

AC Power

?

No

Yes

Plug into AC

Power Outlet

Bad

TV

Is

Red LED on TV

Lit

?

Yes

No

Cycle the power by removing and re-connecting the AC power cord. Observe the

'POWER' LED and TV screen as soon as AC power is re-applied.

1. Bad Analog Board.

2. Bad Digital Board.

Did

Analog

Board 'POWER'

LED Turn On

Momentarily

?

No

Yes

Bad

TV

Did TV

Turn On

Momentarily

?

Yes

No

Check to see if TV is in Commercial Mode.

See Commercial Mode

Check chart.

206-4071

Press 'POWER' or 'ON/OFF' key on TV

Did

TV Turn

On

?

Yes

No

Press 'POWER' or 'ON/OFF' or 'VOLUME UP/DOWN' or

'MUTE' key on Installer

Remote

1. Bad TV

Did

TV

Respond

?

No

Yes

1. Bad TV

2. Go to Remote

Control Checklist page 5

Press 'POWER' or 'ON/OFF' or 'VOLUME UP/DOWN' or 'MUTE' key on

User-Supplied Remote

Did

TV

Respond

?

Yes

No

1. Bad PPV Card

2. Go to Remote

Control Checklist page 5

End

P A G E 4 9

Commercial Mode Check

Press the "On/Off" key on the front panel.

The On/Off key is always operational.

Did you get a response

?

No

Bad TV

Yes

Leave the

TV set On

Go to Installer menu by pressing "MENU" until the TV stops responding.

Did

TV stop responding or continue to respond

?

Continued to respond

Stopped responding

TV is in

Commercial

Mode.

TV is not in Commercial Mode

Call Technical Support for

Assistance

P A G E 5 0

206-4071

Glossary of Terms

A list of definitions for some of the words found in this guide

75 OHM RF CABLE

The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire sticking through the middle. It screws onto the

Antenna/Cable threaded jack on the back of the TV.

300 TO 75 OHM ADAPTER

A small device that connects a twowire 300 ohm antenna to a 75 ohm RF jack.

They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end.

ANALOG TELEVISION

Standard television broadcasting format in

4:3 picture aspect ratio.

A/V CABLES

Audio/Video cables. Three cables bunched together—right audio (red), left audio

(white), and video (yellow). A/V cables are used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices.

A/V DEVICE

Any device that produces video or sound

(VCR, DVD, cable box, or television).

DIGITAL TELEVISION

High-resolution, cinema-quality television signals transmitted digitally.

DVI

Digital Video Interface

Accommodates analog and digital interfaces with a single connector.

PHYSICAL CHANNEL NUMBER

See Note 1.

COMPOSITE VIDEO

Typical video jack, uses one wire for transporting three-color video signals.

RGB (Red, Green, Blue)

Connection input or output port available for producing a video image using three separate colors: Red, Green, and Blue.

COMPONENT VIDEO

Uses three wires for transporting three-color video signals. The end result is usually better video quality.

RS-232

Serial communication port through which the display panel is controlled.

DELETED

Lets you remove channels from the list that the end user can scroll through using CH

(Channel) Up/Down.

2ND AUDIO PROGRAMMING/SAP

Second Audio Programming (SAP) is another, separate audio channel available with some programming. Choosing SAP often refers to listening to audio in another language, such as Spanish or French.

HDMI

High-definition multi-media interface.

OUTPUT

Refers to the output jack that sends a signal out of a VCR, DVD, or other A/V device.

SIGNAL

Picture and sound traveling through a cable, or over the air, to the TV.

HDTV

High-definition television. Refers to television signals that have higher resolution than ordinary analog TV signals.

STEREO SOUND

Stereo (Stereophonic) sound refers to audio that’s divided into right and left sides.

AMPLIFIER

An electronic device that amplifies sound from a television, CD player, VCR, DVD, or other Audio/Video device.

HDSTB

High-definition set top box. Refers to a tuner device that receives high-definition television signals which have higher resolution than ordinary analog TV signals.

TUNER

Device that picks up the broadcast signal and turns it into picture and sound.

VIRTUAL CHANNEL NUMBER

See Note 1.

ANTENNA

The physical receiver of television signals sent over the air. A large metal piece of equipment does not always have to be visible to be using an antenna.

CABLE

Cable service box. Refers to the descrambler box cable subscribers use to receive cable programming signals.

CATV

Programming provided by a cable service.

INPUT

Refers to the input jack that receives a signal from a TV, VCR, DVD Player or other

Audio/Video device.

JACK

An input or output connector on the back of a TV, VCR, DVD Player or other

Audio/Video device.

MONO SOUND

Mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio.

XDS

Extended Data Service: Additional program information included on the signal provided at the discretion of the broadcaster.

Note 1

Refer to www.atsc.org for further information.

206-4071

P A G E 5 1

For Customer Support/Service Please call:

1-888-865-3026

www.lgcommercial.com

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.

1000 Sylvan Avenue

Englewood Cliffs, NJ 07632

© Copyright 2008, LG Electronics U.S.A., Inc.

206-4096

Issue-C

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project