Operator`s manual | Cub Cadet 930 SWE Snow Blower User Manual

Safety • Assembly • Operation • Tips & Techniques • Maintenance • Troubleshooting • Parts Lists • Warranty
OPERATOR’S MANUAL
31AE9PSV710
31AE9LSU710
31AE9LSU756
Model 31AE9PSV710 shown
Two Stage Snow Thrower — Models 930 SWE & 933 SWE
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any uniiproved forest-covered, brushcovered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester
for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland,
Ohio 44136-0019.
PRINTED IN U.S.A
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
FORM NO. 769-02572
6/28/06
This Operator’s Manual is an important part of your new snow thrower. It will help you assemble,
prepare and maintain the unit for best performance. Please read and understand what it says.
Table of Contents
Customer Support............................................... 2
Safety Labels....................................................... 3
Safe Operation Practices.................................... 4
Setting Up Your Snow Thrower........................... 6
Operating Your Snow Thrower.......................... 10
Making Adjustments......................................... 14
Maintaining Your Snow Thrower....................... 16
Off-Season Storage........................................... 22
Troubleshooting................................................. 23
Illustrated Parts List.......................................... 24
Warranty............................................................. 31
Specifications are subject to change without notification or obligation. Images may not reflect your exact model and are for reference purposes only.
Finding and Recording Model Number
BEFORE ASSEMBLING YOUR NEW EQUIPMENT,
please locate the model plate on the equipment
and copy the information to the sample model plate
provided to the right. You can locate the model plate
by standing at the operating position and looking
down at the rear of the snow thrower. This information
will be necessary to use the manufacturer’s web site
or when obtaining assistance from an authorized Cub
Cadet dealer.
CUB CADET LLC
P. O. BOX 361131
www.cubcadet.com CLEVELAND, OH 44136
DEALER LOCATOR PHONE NUMBER: 877-282-8684
Customer Support
If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this
unit, you can contact the dealer you purchased the unit from or choose from the options below:
3.The engine manufacturer is responsible for all enginerelated issues with regards to performance, power-rating,
specifications, warranty and service. Please refer to the
engine manufacturer’s Owner’s/Operator’s Manual, packed
separately with your unit, for more information.
1. Visit cubcadet.com for many useful suggestions. Click on
Customer Service or the Service Locator to find the nearest
Cub Cadet service dealer in your area.
2.To reach the Customer Dealer Referral Line, please call
1-877-282-8684.
$!.'%2
+%%0!7!9&2/-2/4!4).')-0%,,%2
!.$!5'%2#/.4!#47)4()-0%,,%2/2
!5'%2#!.!-054!4%(!.$3!.$&%%4
53%#,%!./544//,4/5.#,/'
$)3#(!2'%#(54%
$)3%.'!'%#,54#(,%6%2334/0%.').%
!.$2%-!)."%().$(!.$,%35.4),!,,
-/6).'0!243(!6%34/00%$"%&/2%
5.#,/'').'/23%26)#).'-!#().%
4/!6/)$4(2/7./"*%#43).*52)%3
.%6%2$)2%#4$)3#(!2'%!4"934!.$%23
53%%842!#!54)/.7(%./0%2!4).'/.
'2!6%,352&!#%3
2%!$/0%2!4/2g3-!.5!,
#,%!./544//,
$!.'%2
1
Safety
Labels
!6/)$).*529&2/2/4!4).'!5'%2
+%%0(!.$3&%%4
!.$#,/4().'!7!9
$!.'%2
.%6%2054(!.$).#(54%#/.4!#47)4(
2/4!4).'0!243#!.!-054!4%&).'%23
!.$(!.$3
3(54/&&%.').%!.$7!)45.4),!,,
-/6).'0!243(!6%34/00%$"%&/2%
5.#,/'').'
53%#,%!./544//,/27//$%.34)#+4/
5.#,/'$)3#(!2'%#(54%
WARNING
This symbol points
out important safety
instructions which, if
not followed, could
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
instructions in this
manual before attempting to operate
this machine. Failure
to comply with these
instructions may result
in personal injury. When
you see this symbol.
HEED ITS WARNING!
A chute clean-out tool is fastened to the top of the
auger housing with a mounting clip. The tool is designed
to clear a chute assembly of ice and snow.
This item is fastened with a cable tie at the factory. Cut
the cable tie before operating the snow thrower.
WARNING: Never use your
hands to clear a clogged chute
assembly. Shut off engine and
remain behind handles until
all moving parts have stopped
before using the clean-out tool
to clear the chute assembly.
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
2
Safe
Operation
Practices
WARNING
This symbol points
out important safety
instructions which, if
not followed, could
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
instructions in this
manual before attempting to operate
this machine. Failure
to comply with these
instructions may result
in personal injury. When
you see this symbol.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to State of California to cause cancer and
birth defects or other reproductive harm.
DANGER: This machine was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. This machine is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury or death.
Training
Preparation
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
2. Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them quickly.
3. Never allow children under 14 years old to operate this
machine. Children 14 years old and over should read and
understand the operation instructions and safety rules in
this manual and should be trained and supervised by a
parent.
4. Never allow adults to operate this machine without proper
instruction.
5. Thrown objects can cause serious personal injury. Plan
your snow-throwing pattern to avoid discharge of material
toward roads, bystanders and the like.
6. Keep bystanders, helpers, pets and children at least 75 feet
from the machine while it is in operation. Stop machine if
anyone enters the area.
7. Exercise caution to avoid slipping or falling, especially
when operating in reverse.
1. Thoroughly inspect the area where the equipment is to be
used. Remove all doormats, newspapers, sleds, boards,
wires and other foreign objects, which could be tripped over
or thrown by the auger/impeller.
2. Always wear safety glasses or eye shields during operation
and while performing an adjustment or repair to protect your
eyes. Thrown objects which ricochet can cause serious
injury to the eyes.
3. Do not operate without wearing adequate winter outer
garments. Do not wear jewelry, long scarves or other
loose clothing, which could become entangled in moving
parts. Wear footwear which will improve footing on slippery
surfaces.
4. Use a grounded three-wire extension cord and receptacle
for all units with electric start engines.
5. Adjust collector housing height to clear gravel or crushed
rock surfaces.
6. Disengage all control levers before starting the engine.
7. Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator’s manual.
8. Let engine and machine adjust to outdoor temperature
before starting to clear snow.
9. To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive. Serious personal injury can
occur when gasoline is spilled on yourself or your clothes,
which can ignite. Wash your skin and change clothes
immediately.
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the engine is hot
or running.
e. Allow engine to cool at least two minutes before refueling.
f. Never over fill fuel tank. Fill tank to no more than ½ inch
below bottom of filler neck to provide space for fuel
expansion.
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine and equipment. Move machine to another area. Wait 5 minutes
before starting the engine.
i. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light (e.g. furnace,
water heater, space heater, clothes dryer etc.).
j. Allow machine to cool at least 5 minutes before storing.
HEED ITS WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
Operation
Maintenance & Storage
1. Do not put hands or feet near rotating parts, in the
auger/impeller housing or chute assembly. Contact with the
rotating parts can amputate hands and feet.
2. The auger/impeller control lever is a safety device. Never
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.
3. The control levers must operate easily in both directions
and automatically return to the disengaged position when
released.
4. Never operate with a missing or damaged chute assembly.
Keep all safety devices in place and working.
5. Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless and
deadly gas.
6. Do not operate machine while under the influence of alcohol
or drugs.
7. Muffler and engine become hot and can cause a burn. Do
not touch.
8. Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
9. Exercise caution when changing direction and while operating on slopes.
10.Plan your snow-throwing pattern to avoid discharge towards
windows, walls, cars etc. Thus, avoiding possible property
damage or personal injury caused by a ricochet.
11.Never direct discharge at children, bystanders and pets or
allow anyone in front of the machine.
12.Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
13.Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.
14.Disengage power to the auger/impeller when transporting or
not in use.
15.Never operate machine at high transport speeds on slippery
surfaces. Look down and behind and use care when
backing up.
16.If the machine should start to vibrate abnormally, stop the
engine, disconnect the spark plug wire and ground it against
the engine. Inspect thoroughly for damage. Repair any
damage before starting and operating.
17.Disengage all control levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments, or
inspections.
18.Never put your hand in the discharge or collector openings.
Always use the clean-out tool provided to unclog the discharge opening. Do not unclog chute assembly while engine
is running. Shut off engine and remain behind handles until
all moving parts have stopped before unclogging.
19.Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
20.If situations occur which are not covered in this manual,
use care and good judgment. Contact your dealer for
assistance.
1. Never tamper with safety devices. Check their proper
operation regularly. Refer to the maintenance and adjustment sections of this manual.
2. Before cleaning, repairing, or inspecting machine disengage all control levers and stop the engine. Wait until the
auger/impeller come to a complete stop. Disconnect the
spark plug wire and ground against the engine to prevent
unintended starting.
3. Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
4. Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
5. Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!”
6. Check controls periodically to verify they engage and
disengage properly and adjust, if necessary. Refer to the
adjustment section in this operator’s manual for instructions.
7. Maintain or replace safety and instruction labels, as necessary.
8. Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
9. Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10.Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
11.Always refer to the operator’s manual for proper instructions
on off-season storage.
Do not modify engine
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
Notice regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and may
include the following emission control systems: Engine Modification (EM) and Three Way Catalyst (TWC) if so equipped.
Your Responsibility
Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual
and on the machine.
2
Safe
Operation
Practices
WARNING
This symbol points
out important safety
instructions, which if
not followed, could
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
instructions in this manual before attempting to
operate this machine.
Failure to comply with
these instructions may
result in personal injury.
When you see this
symbol.
HEED IT’S WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
3
IMPORTANT: Two replacement auger shear pins are
included with this manual (or stowed in the plastic handle
panel). Refer to the Maintenance section for more
information regarding shear pin replacement.
NOTE: All references in this manual to the left or right
side of the snow thrower is from the operating position
only. Exceptions, if any, will be specified.
Setting Up
Your Snow
Thrower
IMPORTANT: This unit is shipped with the engine full of
oil. After assembly, refer to the Tecumseh Engine manual
packed separately with your snow thrower for fuel and oil
fill-up details.
NOTE: Specifications are subject to change without
notification or obligation. Images may not reflect your
exact model and are for reference purposes only.
NOTE: All references
in this manual to the
left or right side of the
snow thrower is from
the operating position
only. Exceptions, if any,
will be specified.
IMPORTANT
This unit is shipped
with the engine full of
oil. After assembly,
refer to the Tecumseh
Engines manual
packed separately with
your snow thrower
for fuel and oil fill-up
details.
1. Observe the lower area of the snow thrower to be
sure both cables are aligned with roller guides before
pivoting handle upward.
Figure 3-1
a. Remove the lower star knob and carriage bolt from
each side of the lower handle. Pull up and back on
upper handle as shown in Figure 3-1. Align upper
handle with the lower handle. Make certain the
springs at the lower end of the auger and drive
cables are securely hooked into their respective
actuator bracket.
2. a.Secure the upper handle and lower handle with the
two star knobs and carriage bolts removed earlier.
See Figure 3-2.
b. Tighten the two star knobs already installed in the
upper holes to firmly secure the upper handle and
support tubes.
Figure 3-2
Specifications are
subject to change
without notification
or obligation. Images
may not reflect your
exact model and are for
reference purposes only.
Figure 3-3
3
3. a.Remove the flat washer and hairpin clip from the
end of the chute directional control. See Figure 3-3.
b. Insert the end of the chute directional control
into the chute bracket and secure with the flat
washer and hairpin clip just removed. If necessary,
the chute bracket can be adjusted. Refer to the
Adjustments section.
Setting Up
Your Snow
Thrower
IMPORTANT: Prior to operating your snow thrower,
refer to Auger Control Test in the Operation section.
Read and follow all instructions carefully and perform
all adjustments to verify your snow thrower is operating
safely and properly.
4. Remove lock nuts and screws securing one of the
flange keepers to the chute assembly.
5. Place chute assembly onto chute base as shown in
Figure 3-4, making sure that the notches engage with
the spiral end of chute directional control.
Figure 3-4
6. Secure flange keeper removed earlier with lock nuts
and screws. Tighten down nuts securing the other two
flange keepers. See Figure 3-5.
7. Check that all cables are properly routed through the
cable guide on top of engine shroud. See Figure 3-6.
The extension cord is fastened with a cable tie to the rear
of the auger housing for shipping purposes. Cut the cable
tie and remove it before operating the snow thrower.
Shear Pin Storage
Holes are located in the plastic dash panel for convenient
shear pin storage. See Figure 3-7.
Figure 3-5
Figure 3-6
Figure 3-7
IMPORTANT
Prior to operating
your snow thrower,
refer to Auger Control
Test in the Operation
section. Read and
follow all instructions
carefully and perform
all adjustments to verify
your snow thrower is
operating safely and
properly.
Specifications are
subject to change
without notification
or obligation. Images
may not reflect your
exact model and are for
reference purposes only.
3
Shift Lever
Chute Tilt Control
Auger
Control
Drive
Control
Setting Up
Your Snow
Thrower
Specifications are
subject to change without
notification or obligation.
Images may not reflect
your exact model and are
for reference purposes
only.
Drive
Control
Cable
Auger
Control
Cable
Figure 3-8
Final Adjustments
Testing Auger Drive Control
Testing Drive Control & Shift Lever
When the auger control is released and in the disengaged
“up” position, the cable should have very little slack, but
should NOT be tight.
1. In a well-ventilated area, start the snow thrower
engine as instructed in the Operation section. Make
sure the throttle is set in the fast position.
2. With the wheel drive control released, push the
snow thrower forward, then pull it back. The machine
should move freely.
2. While standing in the operator’s position (behind the
snow thrower), engage the auger control and allow
the auger to remain engaged for approximately ten
seconds before releasing the auger control. Repeat
this several times.
3. Engage the drive control and attempt to move the
machine both forward and back, resistance should
be felt.
3. With the engine running in the fast position and the
auger control in the disengaged “up” position, walk to
the front of the machine.
4. Move the shift lever into the fast reverse (R2)
position and repeat the previous two steps.
Confirm that the auger has completely stopped
rotating and shows no signs of motion.
If you experienced resistance rolling the unit, either
when repositioning the shift lever from 6 to R2 or when
attempting to move the machine with the drive control
released, adjust the drive control immediately. See
Adjusting Drive and Auger Controls.
4. If the auger shows any signs of rotating, immediately
return to the operator’s position and shut off the
engine. Wait for all moving parts to stop before
readjusting the auger control cable.
Make these final assembly adjustments before
operating your snow thrower for the first time. Failure
to follow these instructions may cause damage to the
snow thrower.
Refer to Figure 3-8 for location of controls.
1. Move the shift lever into sixth (6) position.
3
Adjusting Drive and Auger Controls
1. From beneath the handle, pull downward on the
appropriate cable and unhook the spring found on the
end of the cable from its respective actuator bracket.
Refer to Figures 3-8 and 3-9.
Setting Up
Your Snow
Thrower
2. Slide the spring up the cable to expose the cable
coupler threads and lock nut. Refer to Figure 3-10.
Adjust the lock nut as follows:
3. If adjusting the drive cable, thread the lock nut
outward (down the coupler) to lengthen the cable
and allow the unit to move freely when the control is
released. Thread the lock nut inward (up the coupler)
to shorten the cable to reduce slippage and prevent
the machine from being easily moved with the drive
control engaged.
4. If adjusting the auger cable, thread the lock nut down
to lengthen the cable as necessary to stop the auger
from turning when the control is released.
Figure 3-9
WARNING
WARNING: Do not over-tighten the
cable. Over-tightening may prevent the
auger from disengaging and compromise the safety of the snow thrower.
Do not over-tighten the
cable. Over-tightening may
prevent the auger from
disengaging and compromise the safety of the snow
thrower.
5. Reattach the spring to the actuator bracket.
6. Repeat the wheel drive and auger control tests to
verify proper adjustment. Repeat previous steps if
necessary to attain proper adjustment of each cable.
Tire Pressure (Pneumatic Tires)
The tires are over-inflated for shipping purposes. Check
the tire pressure before operating the snow thrower. Refer
to the tire side wall for tire manufacturer’s recommended
psi and deflate (or inflate) the tires as necessary.
NOTE: If the tire pressure is not equal in both tires, the
unit may pull to one side or the other and the shave plate
will not sit level on the ground.
Figure 3-10
IMPORTANT: Under any circumstance do not exceed
manufacturer’s recommended psi. Equal tire pressure
should be maintained at all times. Excessive pressure
when seating beads may cause tire/rim assembly to
burst with force sufficient to cause serious injury. Refer to
sidewall of tire for recommended pressure.
IMPORTANT: Under any
circumstance do not
exceed manufacturer’s
recommended psi. Equal
tire pressure should be
maintained at all times.
Excessive pressure when
seating beads may cause
tire/rim assembly to burst
with force sufficient to
cause serious injury.
Refer to sidewall of tire for
recommended pressure.
4
Operating
Your Snow
Thrower
Know Your Snow Thrower
Drive Control
Shift Lever
Two-Way
Chute Control™
Auger Control
Gas Cap
Fuel Tank
Oil Fill
Wheel Steering
Control
Headlight
Chute
Directional
Control
Chute
Assembly
Engine Controls
Recoil Starter
Handle
Electric Starter Outlet
Primer
WARNING
Read, understand,
and follow all instructions and warnings
on the machine and
in this manual before
operating.
Ignition
Key
Choke
Control
33-inch model shown
Clean-Out
Tool
Skid Shoe
Throttle
Control
Figure 4-1
Now that you have setup your snow thrower, it’s important to become acquainted with its controls and features.
For detailed starting
instructions and
more information on
all engine controls,
refer to the Tecumseh
Engine manual
packed separately.
Specifications are
subject to change
without notification
or obligation. Images
may not reflect your
exact model and
are for reference
purposes only.
NOTE: For detailed starting instructions and more
information on all engine controls, refer to the
Tecumseh Engines manual packed separately and
Starting The Engine later in this section.
Shift Lever
The shift lever is located in the center of
the handle panel. Place the shift lever
into any of eight positions to control the
direction of travel and ground speed.
Forward
Your snow thrower has six forward (F)
speeds, with position number one (1)
being the slowest speed.
Reverse
Your snow thrower has two reverse (R)
speeds, with position number one (1)
being the slower speed.
Choke Control
The choke control
is found on the rear
of the engine and is
activated by rotating the knob clockwise. Activating the
choke control closes the choke plate on the carburetor
and aids in starting the engine.
Throttle Control
The throttle control is located on the engine.
It regulates the speed of the engine and
will shut off the engine when pushed down
completely.
Primer
Depressing the primer forces fuel directly into
the engine’s carburetor to aid in cold-weather
starting.
Oil Fill
Engine oil level can be checked and oil added
through the oil fill.
10
34/0
Auger Control
The two-way chute control is located on the left side of
the dash panel and is used to control the distance of
snow discharge from the chute.
• To change the angle/distance which snow is thrown,
pivot the joystick forward or backward.
$2)6%
#/.42/,
Chute Directional Control
The chute directional control is located on the left side of
the snow thrower.
• To change the direction in which snow is thrown,
crank clockwise to discharge to the left and counterclockwise to discharge to the right.
'/
The auger control is located on the left handle. Squeeze
the control grip against the handle to engage the augers
and start snow throwing action. Release to stop.
Drive Control / Auger Lock
Wheel Steering Controls
The left and right wheel steering controls are located on
the underside of the handles. Squeeze the right control to
turn right; squeeze the left control to turn left.
Ignition Key
The ignition key must be inserted and snapped in place
in order for the engine to start. Remove the ignition key to
prevent unauthorized use of equipment. Do NOT attempt
to turn the key.
Clean-Out Tool
'/
The drive control is located on the right handle. Squeeze
the control grip against the handle to engage the wheel
drive. Release to stop.
The drive control also locks the auger control so you can
operate the chute directional control without interrupting
the snow throwing process. If the auger control is engaged simultaneously with the drive control, the operator
can release the auger control (on the left handle) and
the augers will remain engaged. Release both controls to
stop the augers and wheel drive.
IMPORTANT: Always release the drive control before
changing speeds.
Two-Way Chute Control™
#(54%$)2%#4)/.!,#/.42/,
$)3#(!2'%
2)'(4
Operating
Your Snow
Thrower
NOTE: Operate the snow thrower in open areas until you
are familiar with these controls.
!5'%2
#/.42/,
$)3#(!2'%
,%&4
4
WARNING: Never use your hands to
clear a clogged chute assembly. Shut
off engine and remain behind handles
until all moving parts have stopped
before unclogging.
The clean-out tool is mounted to the rear of the auger
housing and is designed to clear a clogged chute. Refer
to Using Clean-Out Tool later in this section for instructions on how to properly use it.
NOTE: The clean-out tool is fastened to the rear of the
auger housing with a cable tie. Cut the cable tie before
operating the snow thrower.
Skid Shoes
Position the skid shoes based on surface conditions.
Adjust upward for hard-packed snow. Adjust downward
when operating on gravel or crushed rock surfaces.
#(54%4),4
$/7.
#(54%4),4
50
11
WARNING
The operation of any
snow thrower can result
in foreign objects being
thrown into the eyes,
which can damage your
eyes severely. Always
wear safety glasses
while operating the snow
thrower, or while performing any adjustments or
repairs on it.
Be sure no one other than
the operator is standing
near the snow thrower
while starting engine or
operating snow thrower.
Never run engine indoors
or in enclosed, poorly
ventilated areas. Engine
exhaust contains carbon
monoxide, an odorless
and deadly gas. Keep
hands, feet, hair and loose
clothing away from any
moving parts on engine
and snow thrower.
4
Operating
Your Snow
Thrower
Gas & Oil Fill-Up
Service the engine with gasoline and oil as instructed in
the Tecumseh Engines manual packed separately with
your snow thrower. Read instructions carefully.
WARNING: Use extreme care when
handling gasoline. Gasoline is extremely flammable and the vapors are
explosive. Never fuel machine indoors
or while the engine is hot or running. Extinguish
cigarettes, cigars, pipes and other sources of
ignition.
Starting The Engine
1. Attach spark plug wire to spark plug. Make certain
the metal loop on the end of the spark plug wire
(inside the rubber boot) is fastened securely over the
metal tip on the spark plug.
WARNING
Use extreme care when
handling gasoline.
Gasoline is extremely
flammable and the vapors
are explosive. Never fuel
the machine indoors or
while the engine is hot
or running. Extinguish
cigarettes, cigars, pipes
and other sources of
ignition.
The electric starter is
equipped with a grounded
three-wire power cord
and plug and is designed
to operate on 120 volt AC
household current. It must
be used with a properly
grounded three-prong
receptacle at all times
to avoid the possibility
of electric shock. Follow
all instructions carefully prior to operating the
electric starter.
If you have a grounded three-prong receptacle,
proceed as follows:
1. Plug the extension cord into the outlet located on the
engine’s surface. Plug the other end of extension cord
into a three-prong 120-volt, grounded, AC outlet in a
well-ventilated area.
2. Rotate choke control to FULL choke position (for a
cold engine start). If the engine is already warm, place
choke control in the OFF position instead of FULL.
3. Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center
of the primer when pushing. DO NOT use primer to
restart a warm engine after a short shutdown.
4. Push starter button to start engine.
5. Once the engine starts, immediately release starter
button.
2. Make certain both the auger control and drive control
are in the disengaged (released) position.
6. As the engine warms, slowly rotate the choke control
to the OFF position. If the engine falters, quickly rotate
the choke control back to FULL and then slowly into
the OFF position again.
3. Move throttle control up to FAST position. Insert
ignition key into slot. Make sure it snaps into place.
Do not attempt to turn the key.
7. When disconnecting the extension cord, always unplug
the end at the three-prong wall outlet before unplugging the opposite end from the snow thrower.
NOTE: The engine cannot start unless the key is
inserted into ignition switch.
Recoil Starter
Electric Starter
1. Determine that your home’s wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
WARNING: The optional electric
starter is equipped with a grounded
three-wire power cord and plug, and
is designed to operate on 120 volt AC
household current. It must be used with a properly
grounded three-prong receptacle at all times to
avoid the possibility of electric shock. Follow all
instructions carefully prior to operating the electric
starter.
If your house wiring system is not a three-wire
grounded system, do not use this electric starter under
any conditions.
If your home electrical system is grounded, but a
three-hole receptacle is not available, one should
be installed by a licensed electrician before using the
electric starter.
1. Rotate choke control to FULL choke position (cold
engine start). If the engine is already warm, place
choke control in the OFF position instead of FULL.
2. Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center
of the primer when pushing. DO NOT use primer to
restart a warm engine after a short shutdown.
NOTE: Additional priming may be necessary if the
temperature is below 15° Fahrenheit.
3. Grasp the recoil starter handle and slowly pull the rope
out. At the point where it becomes slightly harder to
pull the rope, slowly allow the rope to recoil.
4. Pull the starter handle with a firm, rapid stroke. Do not
release the handle and allow it to snap back. Keep a
firm hold on the starter handle and allow it to slowly
recoil.
5. As the engine warms, slowly rotate the choke control
to the OFF position. If the engine falters, quickly rotate
the choke control back to the FULL position and then
slowly into the OFF position again.
NOTE: Allow the engine to warm up for a few minutes
after starting. The engine will not develop full power until it
reaches operating temperatures.
12
Stopping The Engine
Operating Tips
Run engine for a few minutes before stopping to help dry
off any moisture on the engine.
1. Move throttle control to STOP position.
NOTE: Allow the engine to warm up for a few minutes.
The engine will not develop full power until it reaches
operating temperature.
2. Remove the ignition key (Do not turn key) to prevent
unauthorized use of equipment.
WARNING: The temperature of the
muffler and the surrounding areas may
exceed 150° F. Avoid these areas.
3. Wipe all snow and moisture from the area around the
engine as well as the area in and around the drive
control and auger control. Also, engage and release
both controls several times.
• If possible, remove snow immediately after it falls.
• Discharge snow downwind whenever possible.
NOTE: Keep the key in a safe place. The engine cannot
start without the ignition key.
4
Operating
Your Snow
Thrower
• Slightly overlap each previous path.
• Set the skid shoes 1/4” below the shave plate for
normal usage. Adjust them upward for hard-packed
snow and downward when using on gravel or crushed
rock.
To Engage Drive
1. With the engine running near top speed, move
shift lever to one of six FORWARD positions or two
REVERSE positions. Select a speed appropriate for
the snow conditions that exist.
Chute Clean-Out Tool
The chute clean-out tool is conveniently fastened to the
rear of the auger housing with a mounting clip. Should
snow and ice become lodged in the chute assembly
during operation, proceed as follows to safely clean the
chute assembly and chute opening:
1. Release both the Auger Control and the Drive Control.
NOTE: Use slower speeds in higher snow and/or until
you are familiar with the snow thrower operation.
2. Squeeze drive control against the right handle and
the snow thrower will move. Release it and the drive
motion will stop.
2. Stop the engine by removing the ignition key.
WARNING
The muffler, engine,
and surrounding
areas become hot
and can cause a
burn. Do not touch.
3. Remove the clean-out tool from the clip which secures
it to the rear of the auger housing. See Figure 4-1.
IMPORTANT: NEVER move the shift lever without first
releasing the wheel drive control. Doing so will cause
premature wear on the drive system’s friction wheel.
4. Use the shovel-shaped end of the clean-out tool to
dislodge and scoop any snow and ice which has
formed in and near the chute assembly.
3. To turn the unit left or right, squeeze the respective
wheel steering control. See Figure 4-1.
5. Refasten the clean-out tool to the mounting clip on the
rear of the auger housing, reinsert the ignition key and
start the snow thrower’s engine.
To Engage Augers
6. While standing in the operator’s position (behind the
snow thrower), engage the auger control for a few
seconds to clear any remaining snow and ice from the
chute assembly.
1. To engage augers and start snow throwing, squeeze
the left hand auger control against the left handle.
Release to stop augers.
2. While the auger control is engaged, squeeze the drive
control to move, release to stop. Do not shift speeds
while the drive is engaged.
NOTE: This same lever also locks auger control so you
can turn the chute control without interrupting the snow
throwing process.
3. Release the auger control; the interlock mechanism
should keep the auger control engaged until the drive
control is released.
4. Release the drive control to stop both the augers and
the wheel drive. To stop the auger, both levers must
be released.
13
NOTE: Use slower
speeds in higher snow
and/or until you are
familiar with the snow
thrower operation.
IMPORTANT
NEVER move the
shift lever without first
releasing the wheel
drive control. Doing so
will cause premature
wear on the drive
system’s friction wheel.
5
Shift Cable
If the full range of speeds (forward and reverse) cannot
be achieved, refer to the figure to the left and adjust the
shift cable as follows:
1. Place the shift lever in the fastest forward speed
position.
Making
Adjustments
2. Loosen the hex nut on the speed selector pivot
bracket. See Figure 5-1.
3. Pivot the bracket downward to take up slack in the
cable.
4. Retighten the hex nut.
5. If further adjustment is needed, you may also utilize
the upper or lower hole in the pivot bracket.
Figure 5-1
Chute Control
WARNING
Once a season or every 25 hours of operation, whichever
is earlier, check whether the two-way chute control™
cables have slackened. If the chute pitch cannot be
moved up or down, the chute control cables will have to
be adjusted.
To adjust these cables, proceed as follows:
Read, understand, and
follow all instructions
and warnings on the
machine and in this
manual before operating.
Never attempt to
make any adjustments
while the engine is
running, except where
specified in operator’s
manual.
6. Check for correct adjustment before operating the
snow thrower.
1. To tighten cable, loosen the top nut and tighten the
bottom nut on the cable.
2. Adjust equally on both sides by working on both
cables. See Figure 5-2.
Drive Control
Figure 5-2
Refer to the Final Adjustment section of the Assembly
instructions to adjust the drive control. To further check
the adjustment, proceed as follows:
1. With the snow thrower tipped forward (be certain to
drain gasoline or place plastic film under the gas cap if
the snow thrower has already been operated), remove
the frame cover underneath the snow thrower by
removing the self-tapping screws. See Figure 5-3.
2. Locate the opening between the axle support bracket
and the front frame support (See Figure 5-4). Looking
through this opening, with the drive control released,
there must be 1/8” clearance between the friction
wheel and the drive plate in all positions of the shift
lever.
Specifications are
subject to change
without notification
or obligation. Images
may not reflect your
exact model and
are for reference
purposes only.
3. With the drive control engaged, the friction wheel must
contact the drive plate. See Figure 5-4.
4. If there is no friction wheel clearance, or the friction
wheel does not solidly contact the drive plate, readjust the lock nut on the lower end of the drive cable
following the instructions in the Assembly section.
5. Reassemble the frame cover.
Figure 5-3
NOTE: If you placed plastic film under the gas cap earlier,
remove it now.
14
5
Skid Shoes
The space between this shave plate and the ground can
be adjusted. For close snow removal, place skid shoes in
the low position. Use middle or high position when area to
be cleared is uneven.
1. Adjust skid shoes by loosening the six hex nuts,
washers, and carriage bolts and moving skid shoes to
desired position. See Figure 5-5.
2. Make certain the entire bottom surface of skid shoes
are against the ground to avoid uneven wear on the
skid shoes.
Friction
Wheel
Making
Adjustments
Drive
Plate
3. Tighten nuts and bolts securely.
Axle Supp.
Brkt.
Opening
Chute Bracket Adjustment
If the spiral at the bottom of the chute directional control
is not fully engaging with the chute assembly, the chute
bracket can be adjusted. To do so:
1. Loosen the two nuts which secure the chute bracket
and reposition it slightly. See Figure 5-6.
Figure 5-4
IMPORTANT: It is not
recommended that
you operate this snow
thrower on gravel as
loose gravel can be
easily picked up and
thrown by the auger
causing personal
injury or damage to
the snow thrower.
2. Retighten the nuts.
Auger Control
To adjust the auger control, refer to the section in this
manual titled “Setting Up Your Snow Thrower”.
Figure 5-5
Figure 5-6
15
If for some reason,
you have to operate
the snow thrower on
gravel, keep the skid
shoe in the highest
position for maximum
clearance between the
ground and the shave
plate.
6
Wheels
At least once a season, remove both wheels. Clean and
coat the axles with a multipurpose automotive grease
before reinstalling wheels.
Chute Directional Control
Once a season, the spiral end on the chute directional
control should be greased with multipurpose automotive
grease.
Maintaining
Your Snow
Thrower
Auger Shaft
At least once a season, remove the shear pins on auger
shaft. Spray lubricant inside shaft, around the spacers.
Also lubricate the flange bearings found at either end of
the shaft. See Figure 6-2.
Grease fittings can also be found at either end of the
auger shaft. Lubricate with a grease gun once a season.
See Figure 6-2.
WARNING
Always stop engine,
disconnect spark
plug, and ground
against engine before
performing any type
of maintenance on
your machine.
Gear Case
The auger gear case is equipped with a grease fitting.
Lubricate with Shell Alvania lead-free grease once a
season (order part number 737-0168). See Figure 6-2.
Figure 6-1
Engine
Refer to the separate Tecumseh Engines manual
packed with your unit for all engine maintenance.
IMPORTANT: To relieve pressure, remove the vent plug
before lubricating the gear case. See Figure 6-2. Failure
to do so could result in damage to the gear case seals.
Lubrication
Augers
Engine
Refer to the Tecumseh Engines manual packed with
your unit for all engine lubrication instructions.
Drive and Shifting Mechanism
At least once a season or after every 25 hours of operation, remove rear cover. Lubricate all chains, sprockets,
gears, bearings, shafts, and the shifting mechanism.
Use engine oil or a spray lubricant. Refer to Figure 6-1.
IMPORTANT
Avoid oil spillage on rubber friction wheel and
aluminum drive plate.
IMPORTANT
NEVER replace the
auger shear pins
with standard pins.
Any damage to the
auger gearbox or other
components, as a result
of doing so, will NOT be
covered by your snow
thrower’s warranty.
IMPORTANT: Keep all grease and oil off the rubber
friction wheel and drive plate.
Shear Pin
The augers are secured to the spiral shaft with shear pins
and cotter pins. See Figure 6-2. If you hit a foreign object
or ice jam, the snow thrower is designed so that the pins
will shear.
1. If augers do not turn, check to see if pins have
sheared.
2. Replace the pins if needed. Two replacement shear
pins and cotter pins have been provided with the
snow thrower. Spray an oil lubricant into shaft before
inserting new pins and securing with new cotter pins.
Vent Plug
Cotter Pin
Grease
Fitting
Spacers
Figure 6-2
16
Bearing
6
Shave Plate and
Skid Shoes
The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. Check these periodically and replace as necessary.
Skid Shoes
NOTE: The skid shoes on this machine have two wear
edges. When one side wears out, they can be rotated
180° to use the other edge.
Skid Shoe
Shave Plate
Maintaining
Your Snow
Thrower
1. Remove the six carriage bolts, hex nuts, and bell
washers that secure the two skid shoes to the sides of
the auger housing. Refer to Figure 6-3.
2. Position the new skid shoes and secure with the carriage bolts, bell washers, and hex nuts. Make certain
the skid shoes are adjusted to be level.
Figure 6-3
Shave Plate
Specifications are
subject to change
without notification
or obligation. Images
may not reflect your
exact model and
are for reference
purposes only.
1. Remove the hex nuts, bell washers, and carriage
bolts that secure the shave plate to the bottom of the
housing.
2. Remove the rear most hex nut, bell washer, and
carriage bolt securing the back of each skid shoe to
the sides of the housing. Loosen the remaining hex
nuts securing the skid shoes.
3. Slide the shave plate out of the off-set slot at the
bottom of the housing, and from between the skid
shoes and side panels of the housing.
4. With the mounting holes toward the back, slide the
new shave plate into position and secure with the
fasteners removed previously.
Figure 6-4
Replacing Belts
1. Disconnect the chute crank assembly at the discharge
chute end by removing the hairpin clip and the flat
washer. Refer to Figure 6-4.
2. Remove the plastic belt cover, located near the
engine, by removing the three self-tapping screws that
secure it. See Figure 6-5.
3. a.Loosen the bolt shown in Figure 6-6 securing the
belt keeper bracket and remove the other bolt.
b.Push the belt keeper and bracket up off the engine
pulley. See Figure 6-7.
Auger Belt
4. Remove the hairpin clip and flat washer from the
ferrule in order to disconnect the auger idler rod from
the brake bracket assembly. See Figure 6-8.
5. Unhook the spring found on the end of the auger
cable from its respective actuator bracket. Refer to
Figure 3-10 in the “Setting Up Your Snow Thrower”
section.
Figure 6-5
17
6
Maintaining
Your Snow
Thrower
Remove
6. Slip the auger control belt (the front belt) off the
engine pulley.
7. Pull the brake bracket assembly towards the cable
guide roller and unhook the auger cable “Z” fitting.
See Figure 6-9.
8. Remove the upper bolts which attach the auger housing
assembly to the frame assembly using a 9/16” wrench.
Refer to Figure 6-4 on previous page.
9. Place a block of wood underneath the auger housing as
shown in Figure 6-10 and separate auger housing from
the frame by tilting the housing forward and pulling up
the handles.
Loosen
Figure 6-6
10.a.Using a 1/2” wrench, remove the hex screw and
cupped washer from the center of the pulley on the
auger housing. See Figure 6-11.
b. Lift the brake bracket assembly out of the pulley
groove
c. Remove the pulley. Be careful not to lose the key.
11.Remove and replace auger belt inside belt keepers.
12. Apply Loctite 262 to the threads of the hex screw used
for mounting the auger pulley.
WARNING
13.Reassemble pulley to auger housing with hex screw
and cupped washer (cupped side toward the pulley).
Torque hex screw 150-250 in. lbs.
Always stop engine,
disconnect spark
plug, and ground
against engine before
performing any type
of maintenance on
your machine.
NOTE: Make sure key is in place on shaft and brake puck
is seated in the pulley groove.
Figure 6-7
Figure 6-8
18
6
If also replacing the drive belt, proceed to the “Drive Belt”
instruction. If not, reassemble by performing the previous
steps in the opposite order and manner of removal.
Proper Adjustment: With the auger clutch lever in the
disengaged position, the top surface of the new belt should
be even with the outside diameter of the pulley.
Maintaining
Your Snow
Thrower
1. To adjust, disconnect ferrule from brake bracket assembly and thread ferrule in (towards idler) to increase
tension on belt, and out to decrease tension.
NOTE: The brake puck must always be firmly seated in the
pulley groove when auger control is disengaged.
Drive Belt
1. Pull the idler pulley away from the backside of the drive
belt to relieve the tension and slide the drive belt off the
idler pulley (If necessary unhook the extension spring
from the belt cover plate). See Figure 6-12.
Figure 6-9
2. Roll the drive belt off the lower drive pulley.
3. Remove the belt from the engine pulley.
Specifications are
subject to change
without notification
or obligation. Images
may not reflect your
exact model and
are for reference
purposes only.
4. Install the new belt on the pulleys in the reverse order and
re-tension with the idler pulley.
5. Reassemble by performing the previous steps in the
opposite order and manner of removal.
Figure 6-10
1
3
B
C
2
A
Figure 6-11
Figure 6-12
19
6
Changing Friction Wheel
The rubber on the friction wheel is subject to wear and
should be checked after the first 25 hours of operation,
and periodically thereafter. Replace the friction wheel if
any signs of wear or cracking are found.
• Drain the gasoline from the snow thrower, or place a
piece of plastic under the gas cap.
Maintaining
Your Snow
Thrower
• Tip the snow thrower up and forward, so that it rests on
the housing.
• Remove screws from the frame cover underneath the
snow thrower. See Figure 6-13.
• Remove the right wheel from the axle.
• Using a 3/4” wrench, hold the hex shaft and remove
the hex screw and cupped washer and bearing from
left side of the frame. Refer to Figure 6-14.
Figure 6-13
• Holding the friction wheel assembly, slide the hex shaft
out of the right side of the unit. The spacer on the left
side of the hex shaft will fall and the sprocket should
remain hanging lose in the chain.
• Lift the friction wheel assembly out between the axle
shaft and the drive shaft assemblies.
WARNING
• Remove four screws securing the friction wheel to the
hub assembly. See Figure 6-15. Discard old friction
wheel.
Always stop engine,
disconnect spark
plug, and ground
against engine before
performing any type
of maintenance on
your machine.
Friction wheel assembly
Remove hex
screw and
washer
Slide hex shaft out
right side
Hex Shaft
Figure 6-14
20
• Reassemble the new friction wheel to the hub
assembly, tightening the four screws in rotation and
with equal force. It is important to assemble the friction
wheel symmetrically for proper functioning.
Hub Assembly
• Insert the pin from the shift arm assembly into the
friction wheel assembly and hold assembly in position.
Refer to Figure 6-16.
6
Maintaining
Your Snow
Thrower
• Slide the hex shaft through the left side of the housing
and through the friction wheel assembly.
• Insert the hex shaft through the sprocket and the
spacer. Make certain that the chain engages both the
large and the small sprocket.
NOTE: If the sprocket fell from the snow thrower while
removing the hex shaft, place the sprocket on the hex
shaft. Position the hex hub of the sprocket toward the friction wheel when sliding the sprocket on to the hex shaft.
Friction Wheel
Figure 6-15
• Secure with the cupped washer and hex bolt removed
earlier.
Specifications are
subject to change
without notification
or obligation. Images
may not reflect your
exact model and
are for reference
purposes only.
• Secure the frame cover with self-tapping screws. Put
the snow thrower down to its normal operating position.
NOTE: If you placed plastic film under the gas cap, be
certain to remove it.
Figure 6-16
21
7
Off-Season
Storage
If the snow thrower will not be used for 30 days or longer, or if it is the end of the snow season when the last possibility of snow is gone, the equipment needs to be stored properly. Follow storage instructions below to ensure top
performance from the snow thrower for many more years.
Preparing Engine
Preparing Snow Thrower
NOTE: Refer to the engine manual for more detailed
information on preparing the snow thrower engine for
storage.
• When storing the snow thrower in an unventilated or
metal storage shed, care should be taken to rustproof
the equipment. Using a light oil or silicone, coat the
equipment, especially any chains, springs, bearings
and cables.
Short-Term Storage
It is important to prevent gum deposits from forming in
essential fuel system parts of the engine such as the
carburetor, fuel filter, fuel hose, or tank during short-term
storage (15-30 days). To prevent this, treat the fuel
system using a fuel stabilizer.
WARNING
Never store snow thrower
with fuel in tank indoors
or in poorly ventilated
areas, where fuel fumes
may reach an open flame,
spark or pilot light as on
a furnace, water heater,
clothes dryer or
gas appliance.
Fuel left in engine during
warm weather deteriorates
and will cause serious
starting problems.
Never use engine or carburetor cleaning products in
the fuel tank or permanent
damage may occur.
• Remove all dirt from exterior of engine and equipment.
• Follow lubrication recommendations.
• Store equipment in a clean, dry area.
Fuel stabilizer (such as STA-BIL™ or ULTRA-FRESH™)
is an acceptable alternative in minimizing the formation
of fuel gum deposits during storage. Add stabilizer to
gasoline in fuel tank or storage container. Always follow
mix ratio found on stabilizer container. Run engine at least
10 minutes after adding stabilizer to allow it to reach the
carburetor.
WARNING: Never store snow thrower
with fuel in tank indoors or in poorly
ventilated areas, where fuel fumes may
reach an open flame, spark or pilot
light as on a furnace, water heater, clothes dryer or
gas appliance.
CAUTION: Alcohol blended fuels
(called gasohol or using ethanol or
methanol) can attract moisture which
leads to separation and formation of
acids during storage. Acidic gas can damage the fuel
system of an engine while in storage.
Long-Term Storage
To avoid engine problems, the fuel system should be
emptied before storage for 30 days or longer.
WARNING: Fuel left in engine during
warm weather deteriorates and will
cause serious starting problems.
1. Run the engine until the fuel tank is empty and it stops
due to lack of fuel. Do not attempt to pour fuel from the
engine.
WARNING: Never use engine or carburetor cleaning products in the fuel tank
or permanent damage may occur.
2. Remove the spark plug and pour one (1) ounce of
engine oil through the spark plug hole into the cylinder.
Cover spark plug hole with a rag and crank the engine
several times to distribute the oil. Replace spark plug.
22
Problem
Engine fails to start
Cause
Remedy
1. Choke not in ON position.
1. Move choke to ON position.
2. Spark plug wire disconnected.
2. Connect wire to spark plug.
3. Fuel tank empty or stale fuel.
3. Fill tank with clean, fresh gasoline.
4. Engine not primed.
4. Prime engine as instructed in “Operating Your Snow Thrower”.
5. Faulty spark plug.
5. Clean, adjust gap, or replace.
6. Blocked fuel line.
6. Clean fuel line.
7. Safety key not in ignition on engine.
7. Insert key fully into the switch.
1. Unit running on CHOKE.
1. Move choke lever to OFF position.
2. Blocked fuel line or stale fuel.
2. Clean fuel line; fill tank with clean,
fresh gasoline.
3. Water or dirt in fuel system.
3. Drain fuel tank. Refill with fresh fuel.
4. Carburetor out of adjustment.
4. Contact an authorized Service Center.
Engine overheats
1. Carburetor not adjusted properly.
1. Contact Service Center.
Excessive
Vibration
1. Loose parts or damaged auger.
1. Stop engine immediately and disconnect spark plug wire. Tighten all bolts
and nuts. If vibration continues, have
unit serviced by an authorized Service
Center.
1. Spark plug wire loose.
1. Connect and tighten spark plug wire.
2. Gas cap vent hole plugged.
2. Remove ice and snow from gas cap.
Be certain vent hole is clear.
3. Exhaust port plugged.
3. Contact Service Center.
1. Drive control cable in need of adjustment.
1. Adjust drive control cable. Refer to
“Making Adjustments”.
2. Drive belt loose or damaged.
2. Replace drive belt.
1. Chute assembly clogged.
1. Stop engine immediately and disconnect spark plug wire. Clean chute
assembly and inside of auger housing
with clean-out tool or a stick.
2. Foreign object lodged in auger.
2. Stop engine immediately and disconnect spark plug wire. Remove object
from auger with clean-out tool or a
stick.
3. Auger control cable in need of adjustment.
3. Refer to Auger Control Test.
4. Auger belt loose or damaged.
4. Refer to Maintenance section.
5. Shear pin(s) sheared.
5. Replace with new shear pin(s).
Engine runs erratic
Loss of power
Unit fails
to propel itself
Unit fails
to discharge snow
23
8
Troubleshooting
This section addresses
minor service issues.
For further details,
contact an authorized
service center.
Models 930 SWE & 933 SWE
24
50
20
53
58
12
41
43
19
30
55
37
4
35
43
37
52
21
48
34
18
57
33
38
25
36 21
21
54
1
47
11
15
63
17
6
22
11
11
22
60
65
64
5
56
14
10
62
13
61
21
16
26
45
8
3
8
42
32
3
51
78
66
40
74
70
23
28
79
75
49
26
7
31
27
79
49
49
69
72
71
49
73
75
77
7
74
32
59
2
70
40
44
67
68
76
24
39
46
9
Part No.
Description
Ref. No.
Part No.
05244B
Housing, Bearing
41
736-3008
Washer, .344 x .75 x .12
2
784-0315A
Housing, Double D Bearing
42
736-3046A
Washer, 1.01 x 1.86 x .06
3
618-0436
Gear Box Assembly, Auger
43
738-0281
Screw, Shoulder, .625 x .17
4
618-0281A
Bracket Assy, Auger Brake
44
738-04155
Pin, Shear, .25 x 1.75
5
684-0090B
Impellar, 16”
45
738-04157
Axle, Spiral, 30”
6
684-04232
Housing, Auger - 30”
—
738-04158
Axle, Spiral, 33”
684-04233
Housing, Auger - 33”
46
741-0192
Bearing, Flange w/Flats
7
684-04151
Spiral Assy, LH
47
741-04024
Bearing, Self Aligning
8
684-04152
Spiral Assy, RH
48
741-0475
Bushing, Nylon
9
710-0371
Screw, Hex Cap Lock
49
741-0494
Bushing, Flange, 1.051 x 1.16
10
710-04527
Screw, Carriage, Stnls Stl
50
747-0980A
Rod, Auger Idler
11
710-0451
Screw, Carriage, 5/16-18 x .75
51
721-0325
Plug
12
710-0459A
Scr, Hex Cap, 3/8-24 x 1.5
52
754-0222A
V Belt,1/2 x 44
13
710-0528
Scr,Hex Cap, 5/16-18 x 1.25
53
756-0178
Pulley, Flat Idler, 2.75 OD
14
710-04484
Screw, 5/16-18 x .750
54
756-0243
Pulley, Auger Drive, 10.0
15
726-04012
Nut, Push
55
784-0385B
Bracket, Auger Idler
16
629-0071
Extension Cord, 110V
56
790-00264
Bracket, Gear Box Support
17
710-04526
Screw, Carriage, 3/8-16 x 1.0
57
784-5123
Bracket, Chute Crank
18
710-04606
Screw, 5/16-18 x .4300
58
710-0276
Screw, Carriage, 5/16-18 x 1.00
19
711-0677
Ferrule
59
737-3000
Ftg, 3/16
20
712-0116
Nut, Hex Lock, 3/8-24
60
790-00277
Plate, Shave, 30”
21
712-04063
Nut, Flnge Lk, 5/16-18
—
790-00196A
Plate, Shave, 33”
22
712-04065
Nut, Flg Lk, 3/8-16
61
736-04215
Washer, Bell, .37x.87x.06
23
712-04102
Nut, Hex, Stnls Stl, 3/8-16
62
790-00199
Shoe, Skid, Stnls Stl
24
714-0104
Pin, Internal Cotter
63
710-04525
Screw, Carriage, 5/16-18 x .75
25
714-0126
Key, Hi Pro, 3/16 x 3/4
64
712-04103
Nut, Hex, Stnls Stl,
26
714-0135
Key, Woodruff,1/4 x 3/4
65
736-04216
Washer, Bell, .34x.87x.06
27
714-04040
Pin, Bowtie Cotter
66
618-0246
Hsg Assy Auger RH (Inc. 40 & 70)
28
715-0118
Pin, Spirol, 5/16 x 1.75
67
618-0435
Hsg Assy Auger LH (Inc. 40 & 70)
29
725-0157†
Tie, Cable
68
710-1260A
Screw, LD, 5/16-18 x .750
30
731-1696A
Adapter, Chute, 6”
69
711-1133
Shf, Drive, Auger
31
731-05162*
Spacer, 1.0 x 1.5 x 2
70
741-0670
Flange Bearing
32
731-05163
Spacer, 1.0 x 1.5 x 1
71
716-0111
Ext, Ret, Ring
33
731-2635
Clip, Mounting
72
717-1425
Gear, Worm, LH
34
731-2643
Tool, Cleanout
73
721-0145
Seal, Oil
35
732-0858
Spring, Extension
74
736-0266
Washer, Flat, 1.52 ID x 2.0 OD
36
736-0159
Washer, .349 x .879 x .063
75
736-0291
Washer, Flat, .88 ID x .38 OD
37
736-0174
Washer, .625 x .885 x .015
76
737-3000
3/16 Drive Lube Fitting
38
736-0242
Washer, .34 x .872 x .06
77
738-0275
Shf, Gear, Worm
39
750-04020
Spacer, 1.004 x 1.375 x .25
78
741-0184
Brg, Thrust
40
721-0146
Oil Seal
79
741-0217
Sleeve
* 33-inch model only
25
Parts List
GE
CT
FA
1
† Not Shown
9
Description
NUINE
T
S
Ref. No.
O R Y PA R
To order replacement
parts, call the Customer
Dealer Referral Line at
1-877-282-8684,
or visit
www.cubcadet.com to
find the nearest Cub
Cadet service dealer in
your area.
Models 930 SWE & 933 SWE
1
11
12
13
3
21
6
5
8
55
9
4
16
6
17
54
30
14
10
7
8
18
44
20
19
62
14
26
11
43
16
63
37
39
25
23
48
24
56
53
46
36
27
35
33
45
30
29
49
48
28
47
58
60
34
61
59
52
23
42
2
15
57
22
51
51
26
32
31
38
41
50
40
Part No.
Description
Ref. No.
Part No.
684-04106B
Handle Engage Assy - RH
33
731-0846C
Upper Chute
2
731-0851A
Chute, Flange Keeper
34
714-0104
Pin, Internal Cotter Pin
3
731-04894B
Lock Plate
35
710-04187
Hi-Lo Screw, 1/4-15 x 0.5
4
711-04287
Pivot Rod
36
684-04230
2-Way Chute Control™ Assy
5
735-0199A
Rubber Bumper
37
731-04954
Steering Control
6
710-04354
Screw, 1/4-20 x.375
38
710-04326
Screw, #8-16 x 0.50
7
731-04896A
Clutch Lock Cam
39
732-04219A
Clutch Lock Spring
8
712-04081A
Shoulder Nut, 1/4-20
40
720-0201A
Knob, Crank
9
725-04214
Wire Harness
41
735-0234
Grommet, Rubber
10
725-1649
Light Socket
42
720-04072
Knob, Star, 5/16-18
11
720-0274
Handle Grip
43
731-04785
Handle Clutch Lock - LH
12
710-1233
Screw, #10-24 x 0.375
44
684-04105A
Handle Engage Assy - LH
13
738-04122
Shoulder Screw, 1/4-20 x 1.345
45
784-5594
Cable Bracket
14
710-04586
Screw, 1/4-20 x 1.625
46
747-04263
Eye Bolt
15
710-0597
Screw, 1/4-20 x 1.00
47
736-0231
Flat Washer
16
646-0012
Cable Assy, Auger/Drive
48
712-04063
Flange Lock Nut, 5/16-18
17
720-04039
Shift Knob
49
731-1313C
Chute Tilt Cable Guide
18
731-05335
Handle Panel
50
726-0100
Cap, Push, 3/8
19
731-05324
Lens
51
736-0105
Washer, Bel, .375 x .87 x .063
20
725-1629
Lamp
52
736-0185
Washer, .375 x .738 x .063
21
731-04784A
Handle Clutch Lock - RH
53
749-04309
Handle, Upper - LH
22
725-0157
Cable Tie
54
749-04310
Handle, Upper - RH
23
712-04064
Flange Lock Nut, 1/4-20
55
732-04238
Torsion Spring
24
732-0193
Compression Spring
56
736-0267
Flat Washer
25
790-00281
Shift Lever
57
749-0991
Handle, Lower
26
790-00248
Panel Bracket
58
710-0458
Bolt, Carriage, 5/16-18 x 1.75
27
738-04125
Shoulder Screw
59
710-0895
Hi-Lo Screw, 1/4-15 x .75
28
684-04104
Crank, Chute
60
710-0276
Screw, Carriage, 5/16-18 x 1.0
29
746-04341
Speed Selector Cable
61
731-0903D
Lower Chute
30
710-0572
Screw, Carriage, 5/16-18 x 2.5
62
716-04036
Ring, Retainer
31
710-1878
Screw, Hex, 3/8-16 x 1.75
63
738-04126
Pin, 3/16
32
710-1879
Screw, Hex, 3/8-16 x .88
Parts List
GE
CT
FA
1
27
9
Description
NUINE
T
S
Ref. No.
O R Y PA R
To order replacement
parts, call the Customer
Dealer Referral Line at
1-877-282-8684,
or visit
www.cubcadet.com to
find the nearest Cub
Cadet service dealer in
your area.
Models 930 SWE & 933 SWE
81
94
96
78
89
88
85
79
91
90
80
26
95
84
93
98
49
44
83
86
87
92
78
26
79
77
82
62
99
11
22
97
9
38
63
17
24
3
65
4
40
33
25
20
53
34
68
75
66
43
B
5
67
35
8
27
32
51
38
70
56
60
59
76
31
A
19
17
A
36
20
61
64
63
2
34
8
6
18
16
23
71
37
25
43
74
44
46
62
42
54
12
15
B
7
29
21
28
14
1
41
31
50
26 61
49
13
73
55
39
52
58
38
72
47
10
45
31
30
57
69
17
48
28
Part No.
Description
Ref. No.
Part No.
05244B
Housing, Bearing
42
732-0121
Spring, Extension
2
618-0279
Dogg, Steering Drive, LH
43
732-0209
Spring, Extension
3
618-0280
Dogg, Steering Drive, RH
44
712-04064
Flange, Lock Nut, 1/4-20
4
618-0282E
Shaft Assembly, Steering
45
736-0158
Washer, Lock, 5/8
5
618-04178
Assembly, Friction Wheel
46
710-0751
Screw, 1/4-20 x .620
718-04034
Wheel, Friction, Bonded
47
634-0225
Wheel Assembly - LH
710-0896
Screw, Hex Wash
634-0226
Wheel Assembly - RH
6
684-0118A
Bracket, Auger Actuator
734-2031
Tire
7
684-0119A
Bracket, Drive Actuator
734-0255
Valve
8
684-04235
Sprocket, 32T
741-0246A
Bearing
9
790-00218A
Bracket, Shft., Selector, Spd.
48
711-04615
Pin, Clevis
10
684-04212
Bracket, Friction Drive Suprt.
49
736-0242
Washer, Bell., .34 x .872 x .06
11
684-04229
Rod Assembly, Shift
50
736-0300
Washer, .406 x .875 x .059
12
790-00217A
Bracket, Pivot, Selector, Spd.
51
736-0329
Washer, Lock, 1/4
13
710-0538
Screw, Hex Cap Lock,
52
714-0149B
Pin, Internal Cotter
14
790-00156
Bracket, Spacer, Shft.
53
737-3000
Fitting, Lube, 3/16 Drive
15
750-04719
Spacer, .515 ID x .750 OD
54
738-0143
Screw, Shoulder, .498 x .34
16
750-04718
Spacer, .51 ID x 3.66 Lg.
55
738-0279
Spindle, Drive Plate
17
710-1652
Screw, Hex Wash.
56
738-0924A
Screw, Hex Shldr., 1/4-28
18
750-04717
Spacer, .51 ID x 7.895 Lg.
57
741-0163A
Assembly, Bearing/Housing
19
710-3001
Screw, Hex Cap, 3/8-16
58
741-04108
Bearing, Hex Flange
20
750-04703
Spacer., 1.0 ID x 1.50 OD
59
741-04025
Bearing, Self Aligning
21
738-04184A
Screw, Shoulder, .368 x .113
60
741-04076
Bearing, Ball
22
732-04385
Spring, Torsion
61
741-0563
Bearing, Ball
23
711-04279
Shaft, Hex Drive
62
741-0748
Bushing, Flange, .5 ID x .627 OD
24
711-04605
Shaft, Actuator
63
746-04337
Cable, Steering
25
716-04048
Ring, Retainer
64
746-0951
Cable, Auger Idler
26
712-0116
Nut, Hex Insert Jam Lock
65
747-0973
Rod, Drive Clutch
27
712-0138
Nut, Hex, 1/4-28 GR5
66
750-0903B
Spacer, .514 x .632 x 2.44
28
712-04063
Nut, Hex Flnge Insert Lk
67
750-0997
Spacer, .675 x 1.0 x .23
29
712-04065
Nut, Hex Flnge Insert Lk
68
750-1302B
Spacer, .6725 x 1.125 x 2.48
30
712-0413
Nut, Hex Insert Jam Lk
69
756-0344
Pulley, Drive
31
710-04484
TT Screw, 5/16-18 x .750
70
756-0625
Roller, Cable
32
712-0717
Nut, Insert 3/8-16
71
790-00257
Cover, Upper Frame
33
713-0284
Chain, Endless, #41 x 36L
72
790-00259
Cover, Lower Frame
34
713-0286
Chain, #420 x 40L
73
711-04607
Axle, Wheel
35
713-04015
Sprocket, #41 x 10T
74
790-00255
Frame, Transmission
36
714-0135
Key, Woodruff
75
784-0406A
Bracket, Frame Support
37
714-0104
Pin, Internal Cotter
76
784-0407
Bracket, Axle Support
38
716-0104
E-Ring
77
790-00254
Bracket, Belt Cover
39
714-0388
Key, Hi-Pro, 3/16 x 5/8
78
710-0191
Screw, 3/8-14 x 1.25 GR8
40
716-0136
Ring, Retaining
79
710-0237
Screw, 5/16-24 x .625
41
717-0302
Plate, Drive
80
710-0607
Screw, Hx Wash Hd Tapp
29
Parts List
GE
CT
FA
1
Continued on following page
9
Description
NUINE
T
S
Ref. No.
O R Y PA R
To order replacement
parts, call the Customer
Dealer Referral Line at
1-877-282-8684,
or visit
www.cubcadet.com to
find the nearest Cub
Cadet service dealer in
your area.
9
Parts List
Models 930 SWE & 933 SWE
Continued from previous page
Ref. No.
Part No.
Description
81
710-1245B
Screw, Hx Cap 5/16-24
82
710-0654A
Screw, 3/8-16 x 1.00
83
736-0173**
Washer, Flat, .28 x .74 x .063
84
714-0118
Key, Square, 1/4 x 1.5
85
790-00167A
Bracket, Belt Keeper
86
731-2531
Cover, Belt
87
732-0303
Spring, Extension
88
732-0705
Guide, Chute Cable
89
736-0247
Washer, Flat, .406 x 1.25
90
748-0234
Spacer, Shoulder
91
736-0159**
Washer, Flat, .349 x .879
748-0418*
Spacer, .33 ID x 1.01 OD x .36
92
754-0131
V-Belt, 3/8 x 35.5
93
756-0240
Pulley, Flat Idler, 3.0 OD
94
756-0241B
Pulley, Dbl, 3.25 OD
95
784-5726
Bracket, Idler, Drive
96
710-0459A
Screw, 3/8-24 x 1.50
97
754-0222A
V-Belt, 1/2 x 44.0
98
756-0178
Idler, Flat, 2.75 OD
99
784-0385B
Bracket, Idler, Auger
100
750-1148A†*
Spacer 1.02 x 1.63 x .1425
† Not Shown
* 30-inch model only
** 33-inch model only
30
MANUFACTURER’S LIMITED COMMERCIAL WARRANTY FOR:
The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise used for commercial purposes and purchased
and used in the United States and/or its territories and possessions, and
by MTD Products Limited with respect to new merchandise purchased
and used in Canada and/or its territories and possessions (either entity
respectively, “Cub Cadet”).
c.
“Cub Cadet” warrants this product (excluding its normal wear parts as
described below) against defects in material and workmanship for a period
of one (1) year commencing on the date of original purchase and will, at
its option, repair or replace, free of charge, any part found to be defective
in materials or workmanship. This limited warranty shall only apply if
this product has been operated and maintained in accordance with the
Operator’s Manual furnished with the product, and has not been subject
to misuse, abuse, neglect, accident, improper maintenance, alteration,
vandalism, theft, fire, water, or damage because of other peril or natural
disaster. Damage resulting from the installation or use of any part, accessory or attachment not approved by Cub Cadet for use with the product(s)
covered by this manual will void your warranty as to any resulting damage.
e.
Normal wear parts are warranted to be free from defects in material and
workmanship for a period of thirty (30) days from the date of purchase.
Normal wear parts include, but are not limited to items such as: batteries,
belts, blades, blade adapters, grass bags, rider deck wheels, seats, snow
thrower skid shoes, friction wheels, shave plates, auger spiral rubber and
tires.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service
dealer. To locate the dealer in your area:
In the U.S.A.
To locate the dealer in your area, check your Yellow Pages, or contact
Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, or call
1-877-282-8684, or log on to our Web site at www.cubcadet.com.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call
1-800-668-1238 or log on to our Web site at www.mtdcanada.com.
This limited warranty does not provide coverage in the following cases:
a.
b.
The engine or component parts thereof. These items may
carry a separate manufacturer’s warranty. Refer to applicable
manufacturer’s warranty for terms and conditions.
Log splitter pumps, valves, and cylinders have a separate
one- year warranty.
d.
f.
g.
Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior finish
due to use or exposure.
Service completed by someone other than an authorized service
dealer.
Cub Cadet does not extend any warranty for products sold or exported outside of the United States and/or Canada, and
their respective possessions and territories, except those sold
through Cub Cadet’s authorized channels of export distribution.
Replacement parts that are not genuine Cub Cadet parts.
Transportation charges and service calls.
No implied warranty, including any implied warranty of merchantability of fitness for a particular purpose, applies after the applicable
period of express written warranty above as to the parts as identified. No other express warranty, whether written or oral, except as
mentioned above, given by any person or entity, including a dealer
or retailer, with respect to any product, shall bind Cub Cadet. During
the period of the warranty, the exclusive remedy is repair or replacement of the product as set forth above.
The provisions as set forth in this warranty provide the sole and
exclusive remedy arising from the sale. Cub Cadet shall not be liable
for incidental or consequential loss or damage including, without
limitation, expenses incurred for substitute or replacement lawn care
services or for rental expenses to temporarily replace a warranted
product.
Some jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty
lasts, so the above exclusions or limitations may not apply to you.
In no event shall recovery of any kind be greater than the amount of the
purchase price of the product sold. Alteration of safety features of the
product shall void this warranty. You assume the risk and liability for
loss, damage, or injury to you and your property and/or to others and their
property arising out of the misuse or inability to use the product.
This limited warranty shall not extend to anyone other than the original
purchaser or to the person for whom it was purchased as a gift.
HOW LOCAL LAWS RELATE TO THIS WARRANTY: This limited warranty gives you specific legal rights, and you may also have other rights
that vary in different jurisdictions.
IMPORTANT: Owner must present Original Proof of Purchase to obtain
warranty coverage.
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-877-282-8684
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
MANUFACTURER’S LIMITED WARRANTY FOR
The limited warranty set forth below is given by Cub Cadet LLC with
respect to new merchandise purchased and used in the United States, its
possessions and territories, and by MTD Products Limited with respect to
new merchandise purchased and used in Canada and/or its territories and
possessions.
“Cub Cadet” warrants this product against defects in material and
workmanship for a period of three (3) years commencing on the date of
original purchase and will, at its option, repair or replace, free of charge,
any part found to be defective in materials or workmanship. This limited
warranty shall only apply if this product has been operated and maintained
in accordance with the Operator’s Manual furnished with the product, and
has not been subject to misuse, abuse, commercial use, neglect, accident,
improper maintenance, alteration, vandalism, theft, fire, water, or damage
because of other peril or natural disaster. Damage resulting from the
installation or use of any part, accessory or attachment not approved by
Cub Cadet for use with the product(s) covered by this manual will void
your warranty as to any resulting damage.
Normal wear parts are warranted to be free from defects in material and
workmanship for a period of thirty (30) days from the date of purchase.
Normal wear parts include, but are not limited to items such as: batteries,
belts, blades, blade adapters, grass bags, rider deck wheels, seats, snow
thrower skid shoes, shave plates, auger spiral rubber and tires.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service
dealer. To locate the dealer in your area:
In the U.S.A.
To locate the dealer in your area, check your Yellow Pages, or contact
Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, or call
1-877-282-8684, or log on to our Web site at www.cubcadet.com.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call
1-800-668-1238 or log on to our Web site at www.mtdcanada.com.
This limited warranty does not provide coverage in the following cases:
a.
b.
The engine or component parts thereof. These items may carry a separate manufacturer’s warranty. Refer to applicable
manufacturer’s warranty for terms and conditions.
Log splitter pumps, valves, and cylinders have a separate one
year warranty.
c.
d.
e.
f.
g.
Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior finish
due to use or exposure.
Cub Cadet does not extend any warranty for products sold or exported outside of the United States and/or Canada, and
their respective possessions and territories, except those sold
through Cub Cadet’s authorized channels of export distribution.
Replacement parts that are not genuine Cub Cadet parts.
Service completed by someone other than an authorized service
dealer.
Transportation charges and service calls.
No implied warranty, including any implied warranty of merchantability of fitness for a particular purpose, applies after the applicable
period of express written warranty above as to the parts as identified. No other express warranty, whether written or oral, except as
mentioned above, given by any person or entity, including a dealer
or retailer, with respect to any product, shall bind Cub Cadet. During
the period of the warranty, the exclusive remedy is repair or replacement of the product as set forth above.
The provisions as set forth in this warranty provide the sole and
exclusive remedy arising from the sale. Cub Cadet shall not be liable
for incidental or consequential loss or damage including, without
limitation, expenses incurred for substitute or replacement lawn care
services or for rental expenses to temporarily replace a warranted
product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty
lasts, so the above exclusions or limitations may not apply to you.
In no event shall recovery of any kind be greater than the amount of the
purchase price of the product sold. Alteration of safety features of the
product shall void this warranty. You assume the risk and liability for
loss, damage, or injury to you and your property and/or to others and their
property arising out of the misuse or inability to use the product.
This limited warranty shall not extend to anyone other than the original
purchaser or to the person for whom it was purchased as a gift.
HOW STATE LAW RELATES TO THIS WARRANTY: This limited warranty gives you specific legal rights, and you may also have other rights
that vary in different jurisdictions.
IMPORTANT: Owner must present Original Proof of Purchase to obtain
warranty coverage.
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-877-282-8684
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
Download PDF

advertising