Curtis LCD3798 Flat Panel Television User Manual

,
USER S MANUAL
Model: LCD3798
Please read this User Manual carefully to ensure the proper use of this product and
keep this manual for future reference
Contents
1
Safety and warnings...........................................................................................................2-3
2
Introduction........................................................................................................................4
3
Installation............................................................................................... ........................5-8
4
Remote Control ...........................................................................................................9
5
TV Operation.................................................................................................................10-12
6
TV Trouble shooting.......................................................................................................13
-1-
SAFETY AND WARNINGS
IMPORTANT SAFETY INSTRUCTION
CAUTION
1.Read these safety instructions.
RISK OF ELECTRIC SHOCK
DO NOT OPEN!
2.Keep these safety instructions.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK).NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
3.Heed all warnings.
4.Follow all safety instructions.
5.Do not use this apparatus near water.
6.Clean only with dry cloth.
7.Do not block any ventilation openings. Install in
The symbol indicates that dangerous voltages
constituting a risk of electric shock are present
within this unit.
accordance with the manufacturers instructions.
8.Do not install near any heat sources such as radiators ,
The symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
stoves, or other apparatus (including amplifiers)that
produce heat.
WARNING:
9.Protect the power cord from being walked on or
To prevent fire or shock hazard, do not expose this
appliance to rain or moisture.
pinched particularly at power outlets, and the point
where they exit from the apparatus.
Thank you very much for purchasing this TV. To enjoy
your product from the very beginning, read this manual
carefully and keep it handy for easy reference.
10.Only use attachments/accessories specified by the
manufacturer.
11.Unplug this apparatus during lightning storms or
INSTALLATION
when unused for long periods of time.
12.Refer all servicing to qualified service personnel.
Locate the TV in the room where light does not strike
the screen directly.
Total darkness or a reflection on the picture screen can
cause eyestrain. Soft and indirect lighting is recommended
for comfortable viewing.
Allow enough space between the TV and the wall to
permit ventilation.
Avoid extremely warm locations to prevent possible
damage to the cabinet or premature component failure.
This TV can be connected to AC 100-240 Volts. 50/60 Hz.
Never connect to a DC supply or any other power supply.
Do not cover the ventilation openings when using the TV.
Servicing is required when the apparatus has been
damaged in any way, such as the power-supply cord
or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture , does not operate n ormally,
or has been dropped.
13.Apparatus must not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, should be placed on the apparatus.
CAUTION
Never tamper with any components inside the TV, or any
other adjustment controls not mentioned in this manual.
All LCD-TVs are high voltage instruments. When you
clean up dust or water drops on the LCD PANEL or
CABINET, the power cord should be pulled out from the
receptacle, then wipe the TV with a dry soft cloth. During
thunder and lighting, unplug the power cord and antenna
cord to prevent damage to your TV. All repairs to this TV
should only be performed by qualified TV service personnel.
Warning: Change or modifications to this unit not expressly
by the part responsible for compliance could void the user 's
authority to operate the Equipment.
-2-
SAFETY AND WARNINGS
High voltages are used in the operation of this television
receiver. Do not remove the cabinet back from your set.
Refer servicing to qualified service personnel.
Never stand on, lean on, or suddenly push the television or
its stand. You should pay special attention to children.
Serious injury may result if it falls.
To prevent fire or electrical shock hazard, do not expose
the television receiver to rain or moisture.
Do not place your television on an unstable cart, stand,
shelf or table. Serious injury to an individual , and damage
to the television, may result if it falls.
Do not drop or push objects into the television cabinet
slots or openings. Never spill any kind of liquid on the
television receiver.
When the television receiver is not used for an
extended period of time, it is advisable to disconnect
the AC power cord from the AC outlet.
Do not block the ventilation holes in the back cover.
Adequate ventilation is essential to prevent failure of
electrical components.
Avoid exposing the television receiver to direct sunlight
and other sources of heat. Do not stand the television
receiver directly on other products which give off heat,
e.g. video cassette players and audio amplifiers. Do not
place naked flame sources, such as lighted candles on
the television.
Dim:515*320mm(
If the television is to be built into a compartment or similar
enclosure, the minimum distances must be maintained. Heat
build-up can reduce the service life of your television, and
can also be dangerous.
Do not trap the power supply cord under the television
receiver.
-3-
INTRODUCTION
Main features
Accessories
Used as Television, display terminal,PC display
AC Power Cord.........................
1
Infrared Remote Controller......
1
High luminance,wide viewing angle
Can store AIR 2-69,HRC 1-125,IRC 1-125,
CATV 2-125 TV programs
HDMI interface
5
Battery(AAA)...............................2
User s Manual...............................1
BTSC
Main parameter
Vie wing Picture Size(diagonal)
Resolution
Aspect Ratio
TV System
Video Signal System
37
1920x1080
16 : 9
NTSC-M,NTSC-N
PAL/NTSC/SECAM
Receiving Channel
AIR 2-69 HRC 1-125 IRC 1-125 CATV 2-125
Contrast
1500:1
Response Time
6.5ms
Viewing Angle
178
Brightness
500cd/m2
AC 100 V-240 V~ 50/60Hz
190W
2x 8W
Analog RGB(VGA)x1
High-Definition Multimedia Interface (HDMI)x2
Rear Composite Video Input x2
Audio Inputx4
YCb (Pb )Cr (P r)x1
Rear composite Video output x1
Rear Audio output x1
Side Composite Video Input x1
Side S-Video x1
Side HEAD PHONE x1
Inpu t Power Voltage
Po we r consumption
Audio Output Powe r
Signal Input
Horizontal definition
THD 7%
TV line
(H) / 178 (V)
Composite Video input >=350
S- Video Input
>=400
Y Cb(Pb ) Cr(Pr)
>=400
-4-
INSTALLATION
Front panel
KEYBOARD
SOURCE
MENU
CH+
CHVOL+
VOLUSB
3
USB
USB
4
2
1
30
1
30
2
4
5
7
8
1:
Remote control sensor.
2:
Indicator LED: GREEN
POWER ON.
3
6
9
RED
0
ENTER
+
+
VOL
CH
_
_
STANDBY.
3:
Key board
4:
Power: Press this button to turn the unit
SOURCE Display the input source menu.
MENU To display main MENU.
CH+/CHIn Analogue TV mode press CH+ or CH- to
change the channel up and down.
In MENU,press CH+ or CH- to select items
in MENU.
In standby mode, it can turn on the TV.
4 VOL+/VOLAdjust sound level.
In MENU,adjust the item that you selected.
5 USB(optional)
1
2
3
SIDE PANEL(LEFT)
ON from STANDBY mode.
All the terminals are(from up to down):
Press it again to turn the set back to
R
AV2
STANDBY.
L
VIDEO
AV2, S-VIDEO, HEAD PHONE..
NOTE:
AV2 and S-VIDEO share the audio input
channel.
S-VIDEO
HEAD PHONE
Pb
HDMI1 INPUT
L
VGA INPUT
YPbPr
AV1 INPUT
Y
AUDIO
INPUT
R
RF INPUT
PC
AUDIO INPUT
AV3 INPUT
Pr
HDMI2 INPUT
AC-INPUT
100-240V~ 50/60Hz
AV OUTPUT
REAR AV PASTER
VIDEO
L
R
VIDEO
L
R
All the terminals are(from left to right):
AC POWER SOCKET, HDMI2,HDMI1,VGA ,AV1,YPbPr, AUDIO INPUT, PC AUDIO INPUT,
ANTENNA ,AV3 INPUT&AV OUTPUT
Note: 1.CVBS and YPbPr share one audio channel.
2. When HDMI1 port get DVI signal, the PC Audio
receive the audio for HDMI1 port.
3.When HDMI 2 port get DVI signal, the PC Audio
receive the audio for HDMI2 port.
-5-
channel is changed to
channel is changed to
INSTALLATION
ANTENNA
Note:
Aerial connections:IEC(female).
Input impendance:75 unbalanced.
-6-
INSTALLATION
PC
STEPS:
8
Be sure both the TV and computer are Power off.
1.Connect VGA and audio cable
2.Connect power cord
3.Power on the TV, switch to PC mode
4.Power on the PC
HDMI2 INPUT
HDMI1 INPUT
L
VGA INPUT
YPbPr
AV1 INPUT
Y
AUDIO
INPUT
R
RF INPUT
PC
AUDIO INPUT
AV3 INPUT
Pb
Pr
AC-INPUT
100-240V~ 50/60Hz
AV OUTPUT
This sequence is very important.
VIDEO
L
R
VIDEO
L
R
PC
PRESET MODE
RESOLUTION
V.Freq.(Hz)
H.Freq.(KHz)
1
800*600
60
37.88
2
1024*768
60
48.36
3
1280*768
60
47.3
NOTE:
PC V.Freq.(Hz) not more than 60Hz.
-7-
INSTALLATION
AV EQUIPMENT
This TV provides three groups of AV ,one S-Video,one group of YPbPr and for convenient
connection to VCR,DVD or other video equipment. Please refer to the owner s
manual of the equipment to be connected as well.
VIDEO RECORDER
R Pr
G
B
W
VIDEO EQUIPMENT with YPbPr
From audio
output
Y
R
You can use the input terminals on TV set rear as follows.
From video
output
R
G Y
B Pb
B
AC-INPUT
100-240V~ 50/60Hz
HDMI2 INPUT
HDMI1 INPUT
L
VGA INPUT
AV1
YPbPr
INPUT
Y
AUDIO
INPUT
R
AV OUTPUT
Y
Pb
Pr
RF INPUT
PC
AUDIO INPUT
AV3 INPUT
G
W
VIDEO
L
VIDEO
L
Y
R
R
R
W
R
To audio
outputs
R
To video
output
with
terminal
Y Yellow (video)
To audio
Output
W
VIDEO EQUIPMENT
Y
with
terminal
W
R
Y
R Red(audio R)
VIDEO EQUIPMENT
Y
W White(audol L)
To video
output
HDMI
R
AV2
L
with S-video
term inal
HDMI cable not included
VIDEO
VIDEO EQUIPMENT
S-VIDEO
HEAD PHONE
It can be connected to the following appliances: VCR, multi disc player, DVD, camcorder, video game
or stereo system, etc.....
YPbPr can support these video formats:480i,576i,480p,576p,720p,1080i,1080p.
Note: AV2 and S-Video share the audio input channel.
-8-
REMOTE CONTROL
REMOTE CONTROL
1: POWER
TV on/off
2: NUMBER KEY :
For direct access to program. For
a 2 (3) digit program number,
The second (third) digit must be
entered before the dash disappears.
The number, the name (and the sound
mode, in analogue mode) are displayed
for a few seconds.
3: MENU
To display TV menu or to return to the
previous menu.
4: CURSOR
To move within the menu.
5: EXIT
To exit menu.
6: VOL+/To adjust sound level.
7: P .M
To switch picture mode.
8: AUTO
Auto adjust in PC mode.
9: SLEEP
Set time to turn off the TV.
10: V-CHIP
Setting the V-chip level .
11: MUTE
To disable or enable the sound.
12: MTS/SAP
Switch the sound stereo,SAP and
mono.
13: RECALL
To access the previously viewed
program.
14: SOURCE
Change input source.
15: ENTER
Confirms selection.
16: TV DISPLAY
Displays/removes the program
Information
17: S.M
To switch sound mode.
18: CH+/CHTo access the next or previous
Program.
19: ASPECT
To change picture aspect .
20: CC
Switch the close caption mode (CC1CC4,Text1-Text4)
21.Direct key to change input Source.
22. PIP .
Open the PIP/POP window.
23. 3D NR .
To change the level of 3D noise reduce.
24. TV SOURCE
To select the TV source .
25. FREEZE
To Freeze the picture.
MUTE
POWER
1
11
MTS/SAP
2
1
12
3
2
RECALL
4
5
6
7
8
9
MENU
13
0
SOURCE
14
3
15
4
ENTER
16
5
TV DISPLAY
EXIT
6
S.M
+
+
VOL
CH
_
_
P.M
7
ASPECT
AUTO
19
8
SLEEP
V-CHIP
CC
TV
AV
SV
9
10
18
20
21
YPbPr
PIP
22
HDMI
PC
USB
3D NR TV SOURCE FREEZE
24
25
23
-9-
TV OPERATION
1. PICTURE MENU
4.FUNCTION MENU
The first item of the MENU is PICTURE MENU.
You can adjust picture effect here, such as contrast,
brightness, etc.
Press
to move, press
to adjust.
The fourth item of the menu is function menu .You
can adjust settings below :
) SLEEP TIMER: adjust the item, you can set the
sleep timer.
) CLOSE CAPTION: adjust the close caption type.
) PARENT CONTEOL: entre parent control menu,
the default password 6666.See next page for details.
)RESETTING: Reset all the setting to default value.
PICTURE
CONTRAST
50
BRIGHTNESS
50
HUE
50
50
COLOUR
50
SHARPNESS
PICTURE MODE
STANDARD
ASPECT
16:9
COLOUR TEMP
NORMAL
3D NR
MID
SELECT
ADJUST
FUNCTION
MENU
EXIT
Note:
1). HUE only available when receiving NTSC
signal.
2). If contrast, brightness, hue, colour, sharpness
be adjusted, the picture mode will return to
personal.
SLEEP TIMER
OFF
CLOSE CAPTION
OFF
PARENT CONTROL
RESETTING
SELECT
2.SOUND MENU
The second item of the MENU is SOUND MENU.
You can adjust sound here.
Press
to move, press
to adjust.
ADJUST
MENU
EXIT
PARENT CONTROL
You can adjust below settings:
)CHANGE PASSWORD : You can change the
PARENT CONTROL password .
)V-CHIP: You can turn off or on it.
)TV-RATING: You can enter TV rating menu
To adjust.
SOUND
50
BASS
50
TREBLE
BALANCE
50
SOUND MODE
STANDARD
FUNCTION
CHANGE PASSWORD
SELECT
ADJUST
MENU
V-CHIP
EXIT
MOVIE-RATING
Note:
1). If Bass, Treble are adjusted, the sound mode will
return to personal .
3.OSD MENU
The third item of the MENU is OSD MENU.
SELECT
50
OSD V-POSITION
OSD DURATION
50
30
OSD HALFTONE
50
SELECT
ADJUST
MENU
ADJUST
MENU
EXIT
5.CHANNEL MENU
The fifth item of the menu is CHANNEL MENU
(only in TV mode ) You can compete channel search
and setting here.
1).AUTOSCAN:Searchall the channels
Automatically.
).FINE TUNE: Fine tuning the current program.
).SKIP: To skip the current channel.
).SOURCE: Select TV source.
ENGLISH
OSD H-POSITION
PG
E
G
ENGLISH RATING
FRANCE RATING
OSD
OSD LANGUAGE
OFF
TV-RATING
EXIT
-10-
TV OPERATION
CHANNEL
AUTO SCAN
SKIP
OFF
SOURCE
AIR
SELECT
ADJUST
MENU
EXIT
6. PIP
The Sixth item of the MENU is PIP Menu, you can
select PIP or POP operation.
Source
TV AV1 AV2 AV3 DVD S-VIDEO SCART
YPBPR
HDMI1
HDMI2
PC
TV
AV1
AV2
AV3
DVD
S-VIDEO
SCART
YPBPR
HDMI1
HDMI2
PC
Note:
:The two sources cannot do PIP/POP
:The two sources can do PIP/POP.
The sources in the table are optional. If any of these sources are not available in your unit,
please ignore these sources.
6).Sound source
Select the sound source.
7).Swap
Swap the main source and the sub source.
PIP
MULTI WINDOW
OFF
SUB SOURCE
YPBPR
SIZE
LARGE
PIP POSITION
TOP L
BORDER COLOUR
BLUE
SOUND SOURCE
MAIN
In PC mode,there are two items that are different
with other sources.
1. PC MENU
You can adjust picture here, such as contrast,
brightness.
Press
to move, press
to adjust.
SWAP
SELECT
ADJUST
MENU
EXIT
PC
1)Multi window
Open the PIP/POP window
2).Sub source
Select the sub source
3).Size
Adjust the PIP window size
4).PIP Position
Adjust the position of the PIP window
5).Border colour
Adjust the border colour of the sub window
50
CONTRAST
50
BR IGHTNESS
PICTURE MODE
NORMAL
ASPECT
16:9
COLOUR TEMP
SELECT
-11-
ADJUST
MENU
EXIT
TV OPERATION
1).Colour temp: press
to entre the colour temp
MENU.To select the colour temp,that you like.
2.JPEG menu
)Select the JPEG item of the USB menu, and press
to entre the JPEG menu.
)Press
to entre folder or exit folders until
JPEG files are found.
)Press
to display the JPEG files ,press “ MENU ”
button to exit .
Note:
1.Press to select previous picture or next
Picture, press to rotate the picture.
PC
COLOR TEMP.
USER
USER-R
50
USER-G
50
USER-B
50
SELECT
ADJUST
MENU
PICTURE
EXIT
JPG
2.GEOMETRY
1).H-Position: adjust the horizontal position of the
screen.
2).V-Position :adjust the vertical positon of the
screen.
3).Clock: finetune the screen width.
4).Phase: finetune the phase of the sreen,usually don
not Adjust this item.
5).Auto adjust: auto adjust to fit the screen.
FOLDERS
2009/03/10 08:53:00
3.MP3 menu
) Select the mp3 item of the USB menu, and press
to entre the MP3 menu.
)Press
to entre folders or exit folder until Mp3
files are found.
)Press to play the MP3 file ,press “ MENU ” button
to exit.
Note :
When playing the mp3 music, press to move ,and
press to play, stop, pause, etc.
GEOMETRY
H-POSITION
50
V-POSITION
50
CLOCK
50
PHASE
50
AUTO ADJUST
SELECT
ADJUST
MENU
110.JPG1
EXIT
USB Function : (optional)
1.Entre the “ USB ” menu.
1).Press the “s ource ” button to entre the source menu.
2).press to select the “ USB ” .
3).Press to entre the “ USB ” menu.
4).press
to select the JPEG menu or MP3 menu.
Mp3
MP3
110.MP3
VOLUME
EQ
-12-
MUTE
Trouble shooting
Trouble phenomenon
Picture
Audio
Snow
Ghost
Noise
Normal audio
Interfere
Normal Picture
No picture
Inspection
antenna position, direction
or connection
antenna position, direction
or connection
Noise
electronic equipment,car/
motorcycle,fluorescent light
Mute
Volume(inspect wether the
mute function on the remote
control are started , or audio
system are correct or not)
Mute
Power cord is not inserted
Power switch is not opened
Contrast and brightness/volume
setup
Press standby key on the remote
control for inspecting
No color
Normal audio
color control
Scramble
Normal audio
or weak
retune channel
No color
Noise
Audio system
Special Explanation The accessories such as remote control is not belongs
to the guarantee
-13-