Specifications | Curtis RCD641 Car Stereo System User Manual

Table of Contents
STEREO HI-FI SYSTEM
With CD PLAYER
And AM/FM PLL SYNTHESIZED TUNER
Page No
PRECAUTIONS -----------------------------------------------------------------------------------------
E-2
IMPORTANT SAFETY INSTRUCTION ------------------------------------------------------------
E-3
WARNING -----------------------------------------------------------------------------------------------
E-6
INSTALLATION -----------------------------------------------------------------------------------------
E-7
OPERATING ELEMENTS ---------------------------------------------------------------------------
E-8
SETTING UP AND CONNECTING THE STEREO SYSTEM --------------------------------
E-9
CLOCK AND TIMER
---------------------------------------------------------------------------------
E-10
BASIC OPERATION
---------------------------------------------------------------------------------
E-10
LISTENING TO THE RADIO
----------------------------------------------------------------------
E-11
PLAYING CD’S -----------------------------------------------------------------------------------------
E-11
CARE AND MAINTENANCE
----------------------------------------------------------------------
E-12
TROUBLE SHOOTING GUIDE ---------------------------------------------------------------------
E-12
SPECIFICATIONS -------------------------------------------------------------------------------------
E-13
RCD641
OWNER’S MANUAL
-1-
PRECAUTIONS
Please take good note of the following instruction:
l
l
l
l
l
l
The unit must be connected to the
power voltage, which is the same as
the local area. If not, there is a danger
of “burning” the unit that causes a fire.
Do not expose to the temperature
higher than 35ºC.
Avoid installation near heaters or in
areas subjected to direct sunlight.
Ensure good air circulation.
Protect the unit from dust, moisture
and water.
l
l
l
Avoid strong magnetic fields, e.g.
near TVs or speakers for other
units.
Avoid using strong chemical
agents to clean.
Do not grease or oil components,
running mechanisms, etc. The CD
player is designed to be
maintenance free.
Take the unit to approved service
point for servicing.
This symbol indicates that dangerous
voltage constituting a risk of electric shock
is present within this unit.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol indicates that there are
important operating and maintenance
instructions in the literature accompanying
this unit.
IMPORTANT SAFETY INSTRUCTIONS
1.
Read instructions – All the safety and operating instructions should be read before the product
is operated.
2.
Retain instruction – The safety and operating instructions should be retained for future
reference.
3.
Heed Warnings – All warnings on the product and in the operating instructions should be
adhered to.
4.
Follow Instructions – All operating and use instructions should be followed.
5.
Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for cleaning.
6.
Attachments – Do not use attachments not recommended by the product manufacturer as they
may cause hazards.
7.
Water and Moisture – Do not use this product near water-for example, near a bath tub, wash
bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8.
Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a child or adult, and serious damage to the
product. Use only with a cart, stand, tripod bracket, or table recommended by the manufacturer,
or sold with the product. Any mounting of the product should follow the manufacturer’s
instructions, and should use a mounting accessory recommended by the manufacturer.
9.
A product and cart combination should be moved with care. Quick stops, excessive force, and
uneven surfaces may cause the product and cart combination to overturn.
WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
DRIPPING WARNING
The product shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the product.
VENTILATION WARNING
The normal ventilation of the product shall not be impeded for intended use.
CAUTION
CLASS 1 LASER PRODUCT
Use of Controls or adjustments or
performance of procedures other than
those specified herein may result in
hazardous radiation exposure.
CLASS 1 LASER
PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
LASER SAFETY
This unit employs a laser. Only qualified service
personnel should attempt repair.
DANGER: INVISIBLE LASER
RADIATION WHEN OPEN AND
INTERLOCK FAILED OR
DEFEATED. AVOID DIRECT
EXPOSURE TO BEAM.
CAUTION: HAZARDOUS LASER
RADIATION WHEN OPEN AND
INTERLOCK DEFEATED.
10. Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure
reliable operation of the product and to protect it from overheating, and these openings must
not be blocked or covered. Placing the product on a bed, sofa, rug, or other similar surfaces
should never block the openings. This product should not be place in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions
have been adhered to.
11. Power Source – This product should be operated be operated only from the type of power
source indicated on the marking label. If you are not sure of the type of power supply to your
home, consult your product dealer or local power company. For products intended to operate
from battery power, or other sources, refer to the operating instructions.
12. Grounding or Polarization – Caution: To prevent electric shock, match wide blade of plug to
wide slot, fully insert. This plug will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
13. Power-Cord Protection – Power-supply cord should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they exit from the product.
-2-
-3-
14. Lightning – For added protection for this product during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the product due to lightning and
power line surges.
15. Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded so as to provide some protection
against voltage surges and built-up static charges. Article 810 of the National Electric Code,
ANSI/NFPA 70, provides information with regard to proper grounding of the must and
supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit, connections to grounding
electrodes, and requirements for the grounding electrode. (See Figure 2)
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA70
a.
b.
c.
d.
When the power-supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust
only those controls that are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will often require extensive work
by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f.
When the product exhibits a distinct change in performance.
– This indicates a need for service.
21. Replacement Parts – When replacement parts are required, be sure the service technician has
used replacement parts specified by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
22. Safety Check – Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper operating
condition.
23. Heat – The product should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that product heat.
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
16. Power Lines – An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits, as contact with them might be fatal.
17. Overloading – Do not overload wall outlets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
18. Object and Liquid Entry – Never push objects of any kind into this product through openings as
they may touch dangerous voltage points or short-out parts that could result in fire or electric
shock. Never spill liquid of any kind on the product.
19. Servicing – Do not attempt to service this product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
.Reorient or relocate the receiving antenna.
.Increase the separation between the equipment and receiver.
.Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
.Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1)
This device may not cause harmful interference, and
(2)
This device must accept any interference received, including interference that may
cause undesired operation.
20. Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
-4-
-5-
WARNING
Read the instruction manual before you attempt to use the unit. Handle glass panels with care.
Consult your dealer or service personnel if you have questions about the installation, operation or
safety of the unit.
INSTALLATION
l
Make sure unit is plugged into an 110V-127V outlet. Using higher voltage outlets could cause the
unit to malfunction or catch fire. Make sure all electrical connections (including extensions and inter
connectors) are properly made.
Turn unit off before unplugging it from power source.
l
Do not expose to temperatures above 95 ºF.
Do not place unit near heaters or in areas subjected to direct sunlight.
Place unit where there is good air circulation.
Protect unit from dust, moisture, water and other liquids.
Do not place unit near TVs, speakers and other objects that generate strong magnetic fields.
Do not clean with strong chemical agents.
Do not grease or oil components, running mechanisms, etc. CD player is designed to be
maintenance-free.
Do not attempt to service this unit yourself. Take to an approved service center if repairs are
necessary.
Do not operate unit if it is not working normally or has been damaged in any way. Turn unit off,
unplug it from the power source and consult service personnel.
Do not remove any fixed cover. This will increase the chance of electrical shock.
Do not leave unit unattended when in use.
Do not listen to headphones at high volumes.
Do not obstruct vents on unit.
Do not attempt to create your own stand for the unit. Use only the included stand.
Do not push object into any holes, slots or openings on unit.
Do not allow children to operate unit without adult supervision.
with other stand may result in instability causing possible injury.
Above all
l
l
l
NEVER let anyone, especially children, push anything into holes, slots or any other openings
in the case this could result in a fatal electric shock.
NEVER guess or take chances with electrical equipment of any kind.
It is better to be safe than sorry!
Note: If energy saving lamps (Fluorescent) are used in the
Same room as the unit erratic operation may occur.
-6-
Put the main unit and the
speaker on a piece of soft
cloth, which for preventing
scratches the unit front
panel.
Use your finger press on the
decoration part, which are at
the groove of the main unit rear
cabinet and slide down to
release away it from the
groove.
SUPPORT PLATE
SLIDE DOWN THE DECORATING
PART TO REMOVE FROM MAIN
UNIT REAR CABINET
90
60
30
l
Insert the support plate into the groove.
l
Slide up the support plate until it is
locked.
If you put your equipment on a glass table or a very smooth surface. The main unit and
speaker box would be easy to move by hand pushing. You could insert the rubber sleeve to
the bottom of the support plate.
l
l
This product is designed both for placing vertically and horizontally. Removing the support
plate away for horizontal placing. The display can be rotated staying in 1 of 3 kind of viewing
angle (30º, 60º, 90º) as you like.
FOR WALL MOUNTING:
1.
Erratic performance may occur if unit is used in rooms lit with fluorescent lights.
CAUTION – This CD player may be used only with the captioned manufacturer’s stand. Use
RUBBER SLEEVE
FOR TABLE TOP
Use the wall-mounting template
supplied with unit to make anchor
hole marks on the wall. Make
sure the marks are leveled.
2.
Drill 3/16" holes on the marks.
3.
Insert the plastic anchor supplied
with unit through the hole and tap
it until it is flush with the wall.
4.
Inset the screw and tighten the
screw 3mm sway from the wall.
5.
Hang the main unit and the
speakers to the screw.
Screw.
Plastic Anchor
-7-
OPERATING ELEMENTS
SETTING UP AND CONNECTING THE STEREO SYSTEM
15
Front view
1
1. Display
2
2. Power Indicator
3. VOL 5 Button
4. POWER Button
3
5. CD DOOR Open/Close Button
4
6. VOL 6 Button
5
7. Remote Sensor
6
8. CD Function Button
9.
PLAY/PAUSE Button
10. TUNER/BAND Button
11. TIMER Button
12.
/ SEARCH
/ TUNING + Button
13. STOP
Button
14.
/
SEARCH / TUNING - Button
7
8
Remote control
25. MUTE Button
26. TUNING - Button
27.
/
SEARCH Button
28.
PLAY/PAUSE Button
29. LINE IN (AUX IN) Button
30. CD Function Button
31. MODE Button
32. EQ Button
33. RANDOM Button
34. PRESET/REPEAT Button
35. TUNING+ Button
Button
36.
/SEARCH
37. VOL
Button
38.
STOP Button
39. TUNER Function Button
40. BAND Button
FM:
Install the FM Antenna wire connecting
plate to FM Antenna Terminal (19) and
tighten it with a screwdriver. Or plug in the
FM Antenna (optional). If stereo broadcast
received, the STEREO indicator will be
displayed on the display (1)
AM:
This unit is equipped with a built-in directional ferrite antenna, move and rotate the unit for
best reception.
9
10
16
11
12
13
14
17
Speaker connection
18
Left side view
15. RESET Switch - Reset the unit with a sharp tip
16. Headphone Jack
Rear view
17. Subwoofer Socket
18. Aux Input Socket
19. FM Antenna Terminal
FM 75 ohm Antenna Socket (optional)
20. AC Power Cord
21. Left Speaker Terminal
22. Right Speaker Terminal
23. Wall Mounting Hole
24. Support Plate
Antenna connection
23
23
19
20
To insert the speaker cables by pushing down the terminal lever of
Left Speaker Terminal (21) and Right Speaker Terminal (22).
Please ensure the cables are connected into the speaker
terminals with the correct polarities. Connect the left speaker to
the terminals L and the right speaker to the terminals R.
21
22
24
25
48
26
35
37
29
39
31
41
33
43
30
38
SUBWOOFER connection
40
1. Connect one end of a RCA plug signal wire (not included) to Subwoofer Socket (17) and the
other end of wire to your subwoofer.
2. Turn on the unit and your subwoofer.
3. Play your home equipment.
AC Outlet
42
32
44
34
45
-8-
1. Connect one end of a RCA plug signal wire (not included) to Aux Input Socket (18) and the other
end of wire to your home equipment. Make sure the polarity of the right and the left channel is
correct.
2. Press the POWER (4) (43) to switch on the unit
3. Press LINE IN (29) on the remote control while display indicates “LINE”.
4. Play your home equipment.
36
27
28
41.
42.
43.
44.
45.
46.
47.
48.
Grey
LINE IN (AUX IN) connection
46 47
ST/MONO Button
CLOCK ADJ. Button
POWER Button
CD DOOR Open/Close Button
Number 0-9 Button
+10 Button
PROGRAM Button
VOL
Button
Mains connection
This system is designed to operate on AC110V-127V ~60Hz house
current. Connecting this system to any other power supply could result in
damage to the unit, which is not covered by your warranty. If this plug will
not fit into your outlet, you should have your outlet changed by a qualified
licensed electrician.
AC Plug
1. Unwind the AC Power Cord on the main unit.
2. Insert the plug into any convenient AC outlet.
As soon as the unit has been connected with the mains voltage, parts of the unit are in operation
due to the standby function. To switch off the unit completely pull the mains plug.
-9-
CLOCK AND TIMER
CLOCK
1. While unit is off (still plugged in), press CLOCK ADJ. (42) once. Hour digits will flash.
(12,36) and
/
SEARCH (14,27) to select correct hour.
2. Press
/SEARCH
3. Press CLOCK ADJ. (42) again. Minute’s digits will flash.
4. Press
/SEARCH
(12,36) and
/
SEARCH (14,27) to select correct minutes.
5. Press CLOCK ADJ. (42) to set time. Digits will stop flashing and clock will start.
TIMER
Clock should be set before using timer.
1.
2.
3.
4.
5.
6.
Press MODE (31). TIMER ON indicator will flash.
Press PROGRAM (47). Hour digits will flash.
Press
/SEARCH
(12,36) and
/
SEARCH (14,27) to select correct hour.
Press PROGRAM (47). Minute’s digits will flash.
Press
/SEARCH
(12,36) and
/
SEARCH (14,27) to select correct minutes.
Press PROGRAM (47) to set time for Timer On. To cancel Timer On setting, press MODE (31)
several times until you reach the Timer On setting mode. Press TIMER (11) to cancel Timer On
setting.
7. To set Timer Off, press MODE (31) once. TIMER OFF indicator will flash.
8. Press PROGRAM (47). Hour digits will flash.
9. Press
/SEARCH
(12,36) and
/
SEARCH (14,27) to select correct hour.
10. Press PROGRAM (47). Minute’s digits will flash.
11. Press
/SEARCH
(12,36) and
/
SEARCH (14,27) to select correct minutes.
12. Press PROGRAM (47) to set time for Timer Off. To cancel Timer Off setting, press MODE (31)
several times until you reach the Timer Off setting mode. Press TIMER (11) to cancel Timer Off
setting.
BASIC OPERATION
TURNING ON
LCD will illuminate dimly when unit has been successfully plugged in and power is flowing. Press
POWER (2,43) to turn unit on. Power On indicator will light up. Select CD (8,30) or TUNER (10,39)
as the music source. To turn unit off, press POWER again.
LISTENING TO THE RADIO
1.
2.
3.
4.
Press POWER (4) (43) to turn unit on.
Press TUNER (10,39) to select radio mode.
Press BAND (10,40) to select AM or FM band.
Press TUNING + (12,35) or TUNING – (14,26) to select the desired station. For automatic
tuning, press and hold TUNING + (12,35) or TUNING – (14,26) until you approach the desired
station, then tap the buttons until you reach the station. For manual tuning, press TUNING +
(12,35) or TUNING – (14,26) briefly and release. The tuner will skip to the next clear station.
ST/MONO
Repeatedly pressing the ST/MONO (41) switches between stereo and mono reception. The stereo
reception of a station in the FM band is indicated on the display. In case of stereo stations with a
bad reception (noise infested reception) we recommend switching the tuner to mono reception.
STORING PRESET STATIONS
1. Tune radio to the desired station.
2. Press PROGRAM (47).
3. Press PRESET/REPEAT (34) repeatedly to set the preset station number.
4. Press PROGRAM (47) to store station. To store additional stations, repeat above steps. Unit
stores 20 FM and 12 AM preset stations.
Note: You can also select directly the desired program place by pressing numerical buttons "0-9"
(45) or "+10” (46) on the remote control.
PLAYING CD’S
Press POWER (4) (43) to turn unit on and press CD Function button (8,30) to select CD mode.
Press CD DOOR Open/Close (5,44) and place a CD on the spindle so it locks in place. Press CD
DOOR Open/Close (5,44) to close door. The number of tracks and the playing time of the CD will
appear on LCD.
PLAY/PAUSE (9,28) – plays CD. Press
to resume play.
PLAY/PAUSE during play to pause; press again
STOP (13,38) – stops CD play.
VOLUME CONTROL
Press VOL
(3,48) and VOL
(6,37) to adjust the volume level. Press MUTE (25) to turn
volume to 0. Press MUTE (25) again to turn sound back on.
EQ
Press EQ (32) repeatedly to cycle through the equalizer presets. Presets are Flat, Rock, Jazz, Pop
and Classic.
CHANGING DISPLAY
When power is off, press MODE (31) to cycle through the following display options:
Clock, Timer On setting, Timer Off setting.
Press MODE (31) while a CD is playing to cycle through the following display options:
Playing Time, Remaining Time, Clock, Timer On setting, Timer Off setting.
-10-
/SEARCH
(12,36) and
/ SEARCH (14,27) – use to skip to desired track. Hold either
button down to search through a particular track.
PRESET/REPEAT (34) – press to have one track or all tracks play repeatedly. Press again to return
to normal play.
RANDOM (33) – press on remote control during CD play to play tracks in random order. Press
again to return to normal play.
PROGRAMMED PLAY
CD player allows you to program up to 16 tracks in a sequence of your choice.
1. Press PROGRAM (47) while CD play is stopped.
/
SEARCH (14,27) to select the desired song to be
2. Press
/SEARCH (12,36) and
-11-
programmed.
Press PROGRAM (47) when you have reached the desired song. The track will be stored in
PROGRAM.
4. Repeat steps to program additional tracks.
PLAY/PAUSE (9,28) to play the programmed
5. When programming is complete, press
track list.
To review programmed tracks, presses PROGRAM (47) repeatedly. Press STOP to clear
programmed tracks.
3.
Note on CD-R/RW discs
l
Because of non-standardized format definition / production of CD-R/RW, playback quality &
performance are not guaranteed.
l
It is not responsible for the playability of CD-R/RW in any case due to recording conditions
such as PC performance, writing software, media ability and etc.
l
Do not attach a seal or label to either side (the record able side or the labeled side) of a
CD-R/RW disc. It may cause malfunction.
Do not load a un-recorded CD-R/RW disc. It will take over 30 seconds to read the disc. The disc
may be damaged if you try to open the disc compartment while reading the disc.
FM STEREO does not
appear on display.
AM or FM, no sound.
Compact Disc Player
CD Player will not play.
CD skips while playing.
Function inoperative and
jammed
Display no indication or
abnormal indication
CARE AND MAINTENANCE
l
l
l
l
l
l
l
Treat the disc carefully. Handle the disc only by its edges. Never allow your fingers to contact
with the shiny, unprinted side of the disc.
Do not attach adhesive tape, stickers etc., to the disc label.
Clean the disc periodically with soft, lint-free, dry cloth. Never use detergents or adhesive
cleaners to clean the disc. If necessary, use to CD cleaning kit.
If disc skips or gets stuck on a section of the disc, it is probably dirty or damaged (scratched).
When cleaning the disc, wipe in straight lines from the center of the disc to the edge of the
disc. Never wipe in circular motions.
To remove a disc from its storage case, press down on the center of the case and lift the disc
outs, holding it carefully by the edges.
Fingerprints and dust should be carefully wiped off the disc’s recorded surface with a soft
cloth. Unlike conventional records. Compact disc have no groove to collect dust and
microscopic debris, so gently wiping with a piece of soft cloth should remove most particles.
TROUBLESHOOTING GUIDE
Should this unit exhibit a problem, check the following before seeking service.
Symptom
Radio
Noise or sound distorted
on AM or FM broadcasts.
Possible Cause
Solution
Station not tuned properly for
AM or FM
FM: Wire antenna is not
extended.
Retune the AM or FM broadcast
station.
Extend FM Wire antenna.
-12-
AM: The bar antenna is not
positioned correctly.
You have tuned to a mono
station or station too weak.
Unit not at Tuner function AM or
FM band.
Volume at minimum.
Reposition the unit until best
reception is obtained.
Select another FM station.
Press Tuner Function button to
AM or FM.
Increase Volume.
Unit not in CD function mode. Press CD Function button.
CD is not installed or installed Insert CD with label side up.
incorrectly.
Disc is dirty or scratched.
Wipe disc with cloth or use
another disc.
Built-in microcomputer hand up. Use a sharp tip to press into the
reset hole to reset the built-in
microcomputer.
Built-in microcomputer hand up. Use a sharp tip to press into the
reset hole to reset the built-in
microcomputer.
SPECIFICATIONS
Power source -------------------------------- AC110V-127V ~60 Hz
DC 3V “AA” size/UM-3 x 2 pcs (not included) for remote
Handset
Power consumption ------------------------- 28 Watts
Dimension ------------------------------- Unit 340 (W) x 151 (D) x 320 (H) mm (including support plate)
340 (W) x 102 (D) x 320 (H) mm (without support plate)
Speaker 200 (W) x 143 (D) x 320 (H) mm (including support plate)
200 (W) x 94 (D) x 320 (H) mm (without support plate)
Tuning range/sensitivity -------------------- AM 530 ~ 1710KHz/2000 µV/m
FM 87.5 – 108MHz/18uV
Playback system ------------------------------ Vertical type CD mechanism
Frequency response ------------------------- 100 – 18,000 Hz
Power output ----------------------------------- 3.5 Watts @ Maximum per channel
Speaker impedance -------------------------- 3.2 ohms
Headphone impedance --------------------- 8 – 32 ohms
AUX input sensitivity ------------------------- 300 mV
ACCESSORIES
Instruction Manual
Remote Control handset
Support plate
Sleeve For Support plate
1 set
1 pc
6 pc
6 pc
Wall mounting template
Screw
Plastic anchor
1 pc
4 pcs
4 pcs
172-401Y10081-CU
-13-
Download PDF

advertising