Installation Instructions
Discover y Wall Oven
EO, MOH and MOV Series
Part No. 65433 Rev. L
All specifications are subject to change without notice. Dacor ® assumes no liability for changes to specifications.
© 2007 Dacor, all rights reserved.
Table of Contents
Before You Begin............................................................... 1
Important Safety Instructions........................................... 1
Important Information About Safety Instructions............... 1
Safety Symbols and Labels.............................................. 1
General Safety Precautions.............................................. 2
Customer Service Information.......................................... 3
If You Need Help............................................................... 3
Product Data Plate............................................................ 3
Model Identification........................................................... 3
Product Specifications...................................................... 4
Product Dimensions.......................................................... 4
Planning the Installation.................................................... 6
Selecting the Location....................................................... 6
Cabinet Cutout.................................................................. 6
Electrical Specifications.................................................... 9
Installation Instructions..................................................... 9
Parts List........................................................................... 9
Electrical Service Installation.......................................... 10
Final Installation.............................................................. 12
Verify Proper Operation.................................................. 14
Installation Checklist....................................................... 15
Before You Begin...
Important:
•
Installer: In the interest of safety and to minimize problems, read these installation instructions completely and carefully before you begin the installation process. Leave these installation instructions with the customer.
•
Customer: Keep these installation instructions for future reference and the local electrical inspector’s use.
Important Safety Instructions
Important Information About
Safety Instructions
•
The Important Safety Instructions and warnings in
these instructions are not meant to cover all possible
problems and conditions that can occur. Use common
sense and caution when installing, maintaining or operating this or any other appliance.
•
Always contact the Dacor Customer Service Team
about problems and conditions that you don’t understand. See Customer Service Information.
Safety Symbols and Labels
DANGER
Immediate hazards that WILL result in severe personal
injury or death.
warning
Hazards or unsafe practices that COULD result in severe
personal injury or death.
caution
Hazards or unsafe practices that COULD result in minor
personal injury or property damage.
DANGER
IMPORTANT: Do not store or use combustible, flammable, or explosive vapors and liquids (such as gasoline)
inside or in the vicinity of this or any other appliance. Also
keep items that could explode, such as aerosol cans,
away from the oven. Do not store flammable or explosive
materials in adjacent cabinets or areas.
warning
WARNING – NEVER use this appliance as a space
heater to heat or warm the room. Doing so may result in
overheating of the appliance.
warning
WARNING – NEVER cover any slots, holes or passages
in the oven bottom or cover an entire rack with materials
such as aluminum foil. Doing so blocks air flow through
the oven and may cause a fire hazard or carbon monoxide poisoning.
warning
Do not install this appliance outdoors and/or near water,
for example, near a pool.
warning
When using the BROIL and CONVECTION BROIL settings, the oven door must be completely shut.
READ AND SAVE THESE INSTRUCTIONS
1
Important Safety Instructions
General Safety Precautions
To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following:
WARNING
•
Read the accompanying use and care manual
before operating this appliance.
•
•
•
WARNING
•
Keep packaging materials away from children.
Plastic sheets and bags can cause suffocation.
To prevent injury due to the unit tipping forward,
secure the oven to the cabinet using the supplied
mounting screws.
•
If you receive a damaged product, immediately contact your dealer or builder. Do not install or use a
damaged appliance. Do not install or use the appliance if the conduit is damaged.
Keep flammable items, such as paper, cardboard,
plastic and cloth away from hot surfaces. Do not put
such items in the oven. Do not allow pot holders to
touch hot surfaces.
•
Do not wear loose or hanging apparel while using
the oven. Do not allow clothing to come into contact
with the interior of the oven and the surrounding
areas during and immediately after use.
•
Do not use the oven for storage.
•
Do not touch the interior surfaces of the oven during
use. After use, make sure these surfaces have had
sufficient time to cool before touching them.
•
Do not touch the outside surfaces of the oven during the self-clean cycle. They will be hot. Venting
from the oven may cause the trim to become hot.
•
For your safety, do not use the oven to cook without
the convection filter installed. When the filter is not
installed, the spinning fan blades at the back of the
oven are exposed.
This oven must be properly installed and grounded
by a qualified installer according to these installation instructions prior to use. The installer must
show the customer the location of the circuit breaker panel or fuse box so that they know where and
how to turn off electric power to the oven. Dacor
is not responsible for service required to correct a
faulty installation. The owner is responsible to make
sure this appliance is properly installed.
•
Do not use the door handle(s) to lift or move the
oven.
•
A minimum of two people are required to safely
install this appliance.
•
To avoid an electric shock hazard, do not install this
appliance outside or near water. Do not install or
use this appliance if it has been exposed to water.
•
Do not install, repair or replace any part of the oven
unless specifically recommended in the literature
accompanying it. A qualified service technician
should perform all other service.
Non-stick coatings, when heated, can be harmful to
birds. Remove birds to a separate, well-ventilated
room during cooking.
•
To prevent damage, remove the meat probe from
the oven when it is not being used.
•
Do not line the oven with aluminum foil or other
materials. These items can melt or burn up during
self-cleaning and cause permanent damage to the
oven.
•
Do not leave objects, such as aluminum foil, the
meat probe, cookie sheets, etc. on the bottom of
the oven. Objects left on the bottom of the oven
could damage the bake element. In addition, the
objects themselves could be damaged.
•
Do not allow heating elements in the top and bottom of the oven chamber to become covered up
by cookie sheets, aluminum foil, pots, pans, etc.
Covering the heating elements could cause them to
over-heat, damaging the oven.
•
Always ensure that the light fixture lens covers are
in place when using the oven. The lens covers protect the light bulbs from breakage caused by high
oven temperatures or mechanical shock.
•
•
Before performing any type of service or installation, make sure that the electric power to the oven
is turned off at the circuit breaker or fuse box.
•
Only use the oven for cooking tasks expected of a
home appliance as outlined in the literature accompanying it. This oven is not intended for commercial
use.
•
Do not climb on any part of the appliance.
•
Do not leave children alone or unattended in the
area around the oven. Do not allow children to play
with the controls, pull on the handle or touch other
parts of the oven.
•
Do not store items of interest to children above the
oven. Children could be burned or injured while
climbing on the appliance.
•
Do not tamper with the controls. Do not adjust
or alter any part of the oven unless specifically
instructed to do so in this manual.
2
Customer Service Information
If You Need Help...
Model Identification
If you have questions or problems with installation, contact
your Dacor dealer or the Dacor Customer Service Team.
For repairs to Dacor appliances under warranty call the
Dacor Distinctive Service line. Whenever you call, have the
model and serial number of the appliance ready. The model
and serial number are printed on the product data plate.
EO230xxx
A BC D
Dacor Distinctive Service (repairs under warranty only)
A = MODEL TYPE
Phone: (877) 337-3226 (U.S.A. and Canada)
Monday — Friday 6:00 a.m. to 4:00 p.m. Pacific Time
Epicure oven
Millennia oven (horiz. trim)
Millennia oven (vert. trim)
Dacor Customer Service
Phone: (800) 793-0093 (U.S.A. and Canada)
Monday — Friday 6:00 a.m. to 5:00 p.m. Pacific Time
Web site: www.Dacor.com
Product Data Plate
•
The product data plate contains the model and serial
number information and the electrical requirements.
•
It is located inside the oven door, in the slot above the
left hinge (inside the lower door on a double oven). To
read the information on the data plate:
1. Push the data plate tab.
2. Pull the data plate up.
= EO = MOH
= MOV
B = CONFIGURATION
Single oven = 1
Double oven = 2
C = SIZE
27 inch = 27
30 inch = 30
D = FINISH
Epicure:
Black glass=
=
Stainless steel, black chrome trim Stainless steel, chrome trim =
Stainless steel, brass trim =
Stainless steel, copper trim =
BK
SBC
SCH
SBR
SCP
Millennia:
Tab
Stainless steel =S
Data plate
IMPORTANT
Push the product data plate back into place before closing the door.
3
Product Specifications
Product Dimensions
All tolerances: ±1/16 (±1.6 mm), unless otherwise stated.
Model
Number
A
EO127
B
27”
(68.6 cm)
MOH127
MOV127
EO130
MOV130
EO227
MOV227
EO230
MOV230
K
L
9/16”
(1.4 cm)
1”
(2.5 cm)
1 7/8”
(4.6 cm)
®
F
MOH/MOV - Millennia
3 11/16”
(9.4 cm)
G
H
7 3/8”
(18.7 cm)
6 3/8”
(16.2 cm)
50 ½”
(128.3 cm)
J
EO - Epicure
2 5/16”
(5.9 cm)
51 1/16”
(129.7 cm)
30”
(76.2 cm)
MOH230
E
27 3/8”
(69.5 cm)
23 3/8”
(59.4 cm)
27”
(68.6 cm)
MOH227
D
27 15/16”
(71.0 cm)
30”
(76.2 cm)
MOH130
C
25 3/8”
(64.4 cm)
28 3/8”
(72.1 cm)
25 3/8”
(64.4 cm)
28 3/8”
(72.1 cm)
®
3 5/16”
(8.4 cm)
1 1/4”
(3.2 cm)
1 1/4”
(3.2 cm)
22 11/16”
(57.6 cm)
Handle Dimensions - All Models (Side View)
4
Door Dimension - All Models
Product Specifications
Top of
chassis
C
H
E
1 1/4”
(3.2 cm)
D
F
G
B
Utility
cutout
Control panel
front
L
J
K
Chassis notch
side view
66” (167.6 cm)
Flexible conduit
A
Top of
chassis
Single Wall Oven Dimensions
Top of
chassis
C
H
E
1 1/4”
(3.2 cm)
D
F
Utility
cutout
B
Control panel
front
Chassis notch
side view
L
J
K
Top of
chassis
A
G
66” (167.6 cm)
Flexible conduit
Double Wall Oven Dimensions
5
Planning the Installation
Selecting the Location
•
•
Carefully check the location where the oven is to be
installed. The oven should be placed for convenient
access, but away from drafts that may be caused by
doors, windows, and heating, ventilation and air conditioning outlets.
Make certain that electrical power can be provided in
the selected location. Be certain that proper clearance
is provided for the oven door when it is in the open
position.
Model
Number
MOV127
EO130
•
28 ½”
30”
62 ½”
(72.4 cm) (76.2 cm) (158.8 cm)
MOV130
MOV227
The specified minimum cabinet depth and width must
be provided. The cabinet depth and width must completely enclose the recessed portion of the oven.
27” 7/16”
(69.7 cm)
MOH130
•
25 ½”
27”
(64.8 cm) (68.6 cm)
MOH227
EO230
C
25 ½”
27”
56 ½”
(64.8 cm) (68.6 cm) (143.5 cm)
MOH127
EO227
•
B
EO127
Cabinet Cutout
Plan the installation so that all minimum clearances are
met or exceeded. Cutout dimensions shown provide
minimum clearances, unless otherwise noted.
A
50 9/16”
(128.4 cm)
NA
28 ½”
30”
(72.4 cm) (76.2 cm)
MOH230
MOV230
Cabinet cutout dimensions must be used as indicated.
Cutout tolerances: +1/16 (1.6 mm), -0, unless otherwise stated.
C
C
Recommended
electrical
location
Recommended
electrical
location
1“ (2.5 cm)
min. clear to
bottom
of door
A
Single Wall
Oven Cutout
B
3/4” (1.9 cm)
support platform
1“ (2.5 cm) min.
clear to
bottom of
door
Alternate
electrical
location
Double Wall
Oven Cutout
A
B
1 ¾“ (4.5 cm) min.
clear to top of
door for heat
exhaust
1 ¾“ (4.5 cm) min.
clear to top of
31 1/4” (79.4 cm) door for heat
recommended
exhaust
(may be altered)
4“ typical toe kick (shown)
6
3/4” (1.9 cm)
support platform
4“ typical toe kick (shown)
9 5/8” (24.4 cm)
recommended
(may be altered)
Planning the Installation
NOTES:
D
Recommended
electrical
location
1“ (2.5 cm) min.
to bottom of
door
Recommended
electrical
location
•
Cutout tolerances: +1/16 (1.6 mm), -0,
unless otherwise stated.
•
24” minimum cutout depth.
•
3/4” support platform must be flush with
front of cutout. See page 8.
4“ (10.2 cm) min.
between cutouts
A
1 ¾“ (4.5 cm) min.
clear to top of
door for heat
exhaust
Duel Single Wall Oven
Cutout
A
B
B
3/4” (1.9 cm)
support platform
3/4” (1.9 cm)
support platform
Alternate
electrical
location
Alternate
electrical
location
31 1/4” (79.4 cm)
recommended
(may be altered)
4“ typical toe kick (shown)
1“ (2.5 cm) min. to combustibles
1 1/2”
(3.8 cm)
typical counter
36” Typical
(91.4 cm)
A
B
1 ¾“ (4.5 cm) min.
to combustible floor
3/4” (1.9 cm)
support platform
Recommended
electrical
location
Single Wall Oven
Under-Counter Cutout
4“ typical toe kick (shown)
Recommended electrical location
1“ (2.5 cm) min. to combustibles
1 1/2”
(3.8 cm)
typical counter
36” Typical
(91.4 cm)
1 ¾“ (4.5 cm) min.
to combustible floor
4“ (10.2 cm) min.
between cutout
A
A
B
B
3/4” (1.9 cm)
support platform
3/4” (1.9 cm)
support platform
Duel Single Wall
Oven Under
Alternate Counter Cutout
electrical
locations
4“ typical toe kick (shown)
7
Planning the Installation
Cabinet Cutout (Continued)
Support Platform
warning
The top surface of the support platform must be installed
flush with the cutout in the front of the cabinet or wall
and any trim. Failure to install the platform properly
may cause the exhaust vent to deform and/or become
obstructed. An obstructed exhaust area may cause the
oven to malfunction. See below.
Provide a platform within the cabinet to support the oven. A
properly supported piece of 3/4” (1.9 cm) thick plywood is
recommended.
All contact surfaces between the appliance and the cabinet, including the support platform, must be sturdy, straight
and level. The oven cannot be leveled after it has been
installed.
Oven door
Cool air intake
(do not block)
Exhaust deflector
(do not bend)
Support platform
Deformed sheet metal
blocking vent
Exhaust vent
(do not block)
Sheet metal on
bottom of oven
RIGHT
Cabinet front or wall
Support Platform Configuration
8
WRONG
Planning the Installation
Electrical Specifications
important
• Preheat times and cavity temperature recovery times
will be increased slightly if operating on less than a
240 Vac circuit.
• This appliance is provided with electrical connection
leads in a flexible metal conduit. These leads may be
a smaller gage than the standard household wiring of
the dedicated supply circuit, but they are suitable for
connection to these circuits under the jurisdiction of
the National Electric Code, and/or the local inspection
authority.
• Locate the junction box so that the wiring may be disconnected without removing the oven from the wall.
It is the owner’s responsibility to ensure that a qualified
electrician performs the electrical connection of this appliance. The electrical installation, including minimum supply
wire size, must comply with the National Electric Code
ANSI/NFPA 70 (latest revision) and local codes and ordinances.
A copy of this standard may be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, Massachusetts 02269-9101
The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded, single
phase circuit that is protected by a properly sized circuit
breaker or time-delay fuse. If a time-delay fuse is utilized,
fuse both sides of the line (L1 and L2).
Model Type
Single 27”
Single 30”
Double 27”
Double 30”
Dedicated Circuit
Requirements
Total
Connected Load
240 Vac 60 Hz.,
4 wire*, 30 Amp.
dedicated
4.6 kW (19.5 Amp.)
240 Vac 60 Hz.,
4 wire*, 50 Amp.
dedicated
9.25 kW (38.9 Amp.)
* Two 120 Vac hot (L1 and L2), one neutral, one ground.
The above electrical ratings are for reference only. For the
exact ratings see the product data plate. See page 3 for
location.
Installation Instructions
Parts List
Verify that all the parts are included. If any item is missing
or damaged, please contact your dealer immediately. Also
make certain that you have all tools and parts necessary to
ensure a proper installation before proceeding.
•
•
•
Exhaust deflector
◊
27” defector - PN 46050B
or
◊
30” deflector - PN 46051B
•
Mounting and exhaust deflector screw kit
◊
◊
Single oven screw kit - four (4) 3/4” mounting
screws, four (4) 1 1/4” mounting screws and three
(3) exhaust deflector screws - PN 700486-1
or
Standard oven racks two (2) for a single oven, five (5)
for a double oven
◊
27” standard rack - PN 72747
or
◊
30” standard rack - PN 72713
GlideRack™ oven rack, one (1)
◊
27” GlideRack™ oven rack - PN 72948
or
◊
30” GlideRack™ oven rack - PN 72949
•
Stainless steel cleaner - stainless steel models only
PN A302
•
Product literature
Double oven screw kit - Six (6) 3/4” mounting
screws, six (6) 1 1/4” mounting screws and three
(3) exhaust deflector screws - PN 700486-2
•
Meat probe, one (1) - PN 72723
•
Broiler grill and pan - PN 12157
9
Installation Instructions
Electrical Service Installation
warning
• Wire the oven only in compliance with local ordinances.
• If the electrical service provided does not meet the
product specifications, do not proceed with the installation. Call a licensed electrician to install the required
wiring.
• To prevent an electric shock or fire hazard, turn off
power to the circuit at the circuit breaker or fuse box
prior to connecting the wiring to the oven.
1. Before proceeding, turn off power to the circuit to which
the oven will be connected at the circuit breaker or fuse
box.
2. Position the oven directly in front of the cabinet cutout.
3. Feed the appliance conduit into the electrical junction
box and attach it using a UL approved strain relief.
4. Depending upon local codes, utilize one of three methods to connect the appliance to the electrical power:
◊
Connect to a four (4) wire electrical system
◊
Connect to a three (3) wire electrical system, where
local codes permit
◊
Connect to a three (3) wire electrical system with
external ground, according to local codes.
• Improper connection of the electrical wiring can cause
an electric shock hazard and damage the appliance.
Dacor is not responsible for damages resulting from
improper installation.
Connecting to a Four (4) Wire Electrical
System
• Connect the ground terminal (or lead) on the appliance
to a grounded, metallic, permanent wiring system or
grounding conductor.
2. Connect the white wire from the appliance conduit to
the white (neutral) supply wire in the junction box.
• Do not use an extension cord with this appliance.
Such use may result in fire, electric shock or other personal injury.
• Do not install a fuse in the neutral or ground circuit. A
fuse in the neutral or ground circuit may result in an
electric shock hazard.
1. Separate the wires coming out of the appliance conduit.
3. Connect the black wire from the appliance conduit to
the black (L1) supply wire in the junction box.
4. Connect the red wire from the appliance conduit to the
red (L2) supply wire in the junction box.
5. Connect the green wire from the appliance conduit to
the green (ground) wire in the junction box.
• The appliance must be connected to the power supply
with copper wire only. The use of aluminum wire may
result in unsatisfactory connections.
• Flexible armored or non-metallic, sheathed copper
cable (with grounding wire) should be used to connect
the appliance to the junction box. An UL-listed connector must be used to directly connect the cable to the
junction box.
IMPORTANT
Make sure that the conduit is long enough to allow the
oven to be pulled out for service without disconnecting it
from power.
Cable from circuit breaker
panel or fuse box
Junction box
RED
RED
GREEN
GREEN
WHITE
WHITE
BLACK
BLACK
Wire nut
(4 places)
Conduit to
wall oven
Four (4) Wire Junction Box Connection
10
Installation Instructions
Connecting to a Three (3) Wire Electrical
System - Where Local Codes Permit
warning
Do not connect the green appliance conduit wire to the
neutral (white) junction box wire unless local building
codes permit.
1. Separate the wires coming out of the appliance conduit.
2. Connect the green and white wires from the appliance
conduit to the white (neutral) supply wire in the junction
box.
3. Connect the black wire from the appliance conduit to
the black (L1) supply wire in the junction box.
4. Connect the red wire from the appliance conduit to the
red (L2) supply wire in the junction box.
Cable from circuit breaker
panel or fuse box
Junction box
RED
RED
Connecting to a Three (3) Wire Electrical
System with External Ground - Where Local
Codes Permit
warning
• Do not connect the green appliance wire to the junction box or to a cold water pipe unless local building
codes permit.
• Do not ground the appliance to a gas supply pipe or
hot water pipe.
• If connecting the ground wire to a grounded cold water
pipe, connect using a separate copper grounding
wire (No. 10 minimum) and a clamp with an external
grounding screw. The grounded cold water pipe must
have metal continuity to electrical ground and must not
be interrupted by insulating materials. Any insulating
materials must be jumped, with a minimum, 4 AWG
wire to establish continuity to ground.
No. 4 copper
wire
Meter
Metal water
pipe
GREEN
WHITE
WHITE
Clamps
BLACK
BLACK
Bare metal
Insulated Pipe Jumper
Wire nut
(3 places)
Conduit to
wall oven
Three (3) Wire Junction Box Connection (Where Local Codes Permit)
note
If the junction box has been properly grounded by a
licensed electrician, the green (ground) wire from the
appliance conduit may be connected to the junction box
using a loop terminal.
See the diagram on the following page. To connect the
green appliance conduit wire to a grounded cold water
pipe:
1. Separate the wires coming out of the appliance conduit.
2. Connect the white wire from the appliance conduit to the
white (neutral) supply wire in the junction box.
3. Connect the black wire from the appliance conduit to the
black (L1) supply wire in the junction box.
4. Connect the red wire from the appliance conduit to the
red (L2) supply wire in the junction box.
5. Connect the green wire from the appliance conduit to a
grounded cold water pipe as shown. Jumper any insulating
materials as shown above with a length of No. 4 copper
wire. Securely clamp the wire to bare metal at both ends.
11
Installation Instructions
Connecting to a Three (3) Wire Electrical
System with External Ground - Where Local
Codes Permit (Continued)
Cable from circuit
breaker panel or
fuse box
Separate No. 10 min.
copper grounding wire
Wire nut
(4 places)
Junction box
RED
RED
WHITE
WHITE
GREEN
GREEN
BLACK
BLACK
Clamp must be
tight on pipe
Conduit to
wall oven
Three (3) Wire Connection with External Ground
Final Installation
warning
• A minimum of two people are required to safely install
this appliance.
• Do not attempt to disengage the hinge catches with
the door removed from the oven. The hinge springs
could release, causing personal injury.
• Do not lift or carry oven door by the door handle.
• On double ovens, remove the bottom door first to
reduce the chance of damage.
Removing the Oven Door(s)
Due to the weight of this appliance, remove the door(s) to
reduce the lifting load. Removing the door(s) will also provide a place to grip the oven when lifting it into place.
1. Open the oven door completely.
2. Pull the hinge locks forward on both hinges, until they
stop.
12
Installation Instructions
3. Raise the door so that it is at a 15° angle from the front
of the oven. Hold the door with one hand on each side.
Lift the door up and out.
2. Support the oven at all times until it is secured into the
cabinet. Be certain to take all necessary safety precautions.
3. Resting the oven on the cabinet support platform, slide
the oven into the recessed area until the rear edge of
the oven trim post is flush with the cabinet face and
the oven is centered within the cutout. Ensure that
the electrical conduit slides through the opening in the
cabinet platform or coils above the oven chassis as the
oven is slid into place. Do not trap the appliance cable
between the oven case back and the rear wall.
4. Make sure the oven is resting level. Shim it if necessary.
Door Gripping
Points
warning
When installing the mounting screws into composite
cabinets, install them into the sides of the cabinet only.
Mounting screws installed into the front of composite
cabinets will have a tendency to pull loose.
Install the Oven in the Cabinet
warning
• Use an appliance dolly to move the appliance when
installing it or removing it from the wall for service. Use
of an appliance dolly will minimize the risk of personal
injury as a result of the oven tipping.
• Failure to install the mounting screws may result in
movement or tipping of the oven during use, or personal injury.
5. Find the mounting hole locations in the front and side
of the oven trim posts. Drill 1/16” pilot holes in the cabinet
through the front or side of the trim posts. Single oven
models require four (4) holes, while double oven models
require six (6).
6. Install the #6 x 3/4” screws provided in the instructions
envelope. Do not over-tighten.
• Do not block the oven air exhaust and intake located
at the bottom of the oven door(s). Blocking the airflow
may cause cabinet damage and poor baking performance.
IMPORTANT
An oven that is not level may provide poor or inconsistent
baking results.
1. Lift the oven up to the cabinet cutout using the handles
and gripping points shown. Use extreme caution when
lifting the appliance, because it is heavy.
Trim post
Handle
Gripping points
Trim post
Gripping point
13
Installation Instructions
Install Exhaust Deflector
caution
Install the exhaust deflector before installing the oven
door(s).
Attach the exhaust deflector to the front of the oven. It
attaches to the oven just below the oven chamber in the
door jam. On a double oven, the exhaust deflector is
mounted below the bottom oven chamber.
1. Line up the mounting holes on the exhaust deflector
with the screw holes on the front of the oven.
2. Secure it using the three (3) screws provided.
1. Grasp the oven door on opposite sides and hold it at a
15° angle from the front of the oven. See facing page.
2. Slide the hinges into the hinge openings, resting the
bottom of the hinge arms on the hinge receptacles.
3. Continue to hold the door at a 15° angle with one hand
while pushing in on each of the bottom corners of the
door. Push until the notch on the bottom of each hinge
slips over the lower lip of each hinge receptacle.
4. Lower the door to the fully opened position.
5. Rotate the two hinge locks toward the oven. Slowly and
carefully open and close the door completely to make
sure that it is properly installed.
Verify Proper Operation
warning
Read the accompanying use and care manual completely
before using the oven.
1. Remove any packaging from inside the oven(s).
2. On some models there is protective plastic coating over
the stainless steel surfaces. Peel them off before use.
3. Slide the oven racks onto the support racks in the oven
chamber(s) as instructed in the use and care manual.
4. Turn on the power to the oven at the circuit breaker
or fuse box. Set the clock as instructed in the use and
care manual.
5. Set the oven to bake mode as instructed in the use and
care manual.
NOTES: If the oven does not operate properly, follow these
troubleshooting steps:
Reinstall the Oven Door(s)
warning
To avoid damage to the door or personal injury from it
falling off its hinges:
• Make sure that the notch on the bottom of each hinge
rests on top of the lower lip of each hinge receptacle
before attempting to open the oven door.
• Rotate the hinge locks toward the front of the oven
immediately and completely after installation of the
door.
caution
On double ovens: Install the upper door first to prevent
damage to the lower door.
14
•
Verify that power is supplied to the oven.
•
Check for proper electrical connection.
•
Repeat the above bake test.
•
If the appliance still does not work, contact Dacor
•
Distinctive Service at (877) 337-3226. Do not attempt
to repair the appliance yourself. If you need service, be
sure to have the model and serial numbers available
when you call. See page 3 for location.
Dacor is not responsible for the cost of correcting problems
caused by a faulty installation.
Installation Instructions
Lower lip of
hinge receptacle
Notch on bottom
of hinge
Door Installation
Installation Checklist
warning
□□ Plastic coating, if applicable, has been removed from
outside of oven.
□□ All packaging materials have been removed from inside
the oven.
• To ensure a safe and proper installation, the following checklist should be completed by the installer to
ensure that no part of the installation has been overlooked.
□□ Power is turned on at circuit breaker or fuse box.
□□ Proper oven operation has been verified. See page
• Proper installation is the responsibility of the homeowner. The importance of proper installation of your
Dacor oven cannot be overemphasized.
□□ Problems have been noted on the warranty card or dur-
□□ Oven is wired to all applicable codes and Dacor specifications. See pages 9 and 10.
14.
ing the on-line activation. Warranty has been activated
on-line or the warranty card has been filled out completely and mailed.
□□ Oven is level. See page 13.
□□ Oven is secured into cabinet with included screws. See
page 13.
□□ Exhaust deflector has been installed. See page 14.
□□ Oven door(s) have been properly re-installed. See
page 14.
15
Notes
16
Dacor ● 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.Dacor.com