Daewoo 1012 Washer/Dryer User Manual

Washing Machine Instruction Manual
DWD-F1011/1012/1013’S/F1211/1212/1213’S
INSTRUCTION MANUAL
Economic wash system
Using artificial intelligence, the washer uses minimum energy and water by
selecting optimal water lever and washing time.
Low noise system
The washer minimizes the washing and spinning noises by sensing the amount
of laundry.
Child-Lock
The Child-Lock system has been used to prevent children from pressing any
button to change the program during operation.
Nano-silver sterilization washing(Option)
By applying very fine silver particles on essential parts inside, the washer
sterilizes up to 99.9% as is done by boiling wash.
Air bubble washing(Option)
This is an advanced technology that generates millions of air bubbles inside the drum on washing sequence,
and the bubbles dissolve the detergent particles completely and cleanse all the soil in clothes gently and neatly.
CONTENTS
Page
PARTS AND FEATURES.................................................................................................................2
WASHER SAFETY...........................................................................................................................3
INSTALLATION INSTRUCTIONS ....................................................................................................4
INLET HOSE CONNECTION ...........................................................................................................5
ELECTRICAL REQUIREMENTS .....................................................................................................6
OPERATING YOUR WASHER ........................................................................................................7
THE FUNCTIONS OF THE CONTROL PANEL...............................................................................9
WASHING PROCEDURE AND PROGRAM SELECTION.............................................................10
MAINTENANCE .............................................................................................................................19
HOW TO CLEAN THE FILTER ......................................................................................................20
REMOVING STAINS ......................................................................................................................21
TROUBLE SHOOTING ..................................................................................................................22
SPECIFICATION ............................................................................................................................23
A NOTE TO YOU
Thank you for buying a DAEWOO appliance.
DAEWOO washers are easy to use, save time, and help you manage your home better.
This manual contains valuable information about how to operate and maintain your washer property and safely.
Please read it carefully.
PARTS AND FEATURES
The parts and features of your washer are illustrated on the page.
Become familiar with all parts and features before using your washer.
NOTE
The drawings in the book may vary from your washer model.
They are designed to show the different features of all models coverd by this book,
Your model may not include all features.
INLET HOSE
DETERGENT CASE
POWER CORD
CONTROL PANEL
DOOR
HOSE DRAIN
ADJUSTABLE LEG
LOWER COVER
Accessories
Hose drain
Inlet hose
Spanner
2
Manual
Cap holder(3EA)
WASHER SAFETY
Save these instructions
Your safety is important to us.
To reduce the risk of fire, electrical shock, or injury when using your washer adhere to the
following basic precautions.
Read all instructions before using your washer
Please ...
• Have only a qualified person install, repair,
or replace parts on washer.
• Maintain washer properly.
• Protect washer from the weather and keep
it where the temperature will not fall below
freezing.
• Do not install the washer at a place of
extremely high humidity. It could cause an
electric shock or a short circuit.
• Connect washer to the correct outlet,
electrical supply, water supply, and drain
supply.
• Flammable fluids (dry-cleaning solvents,
kerosene, gasoline, etc.) should not be used
or stored in or near your washer.
Do not add flammable fluids to your wash
water.These substances give off vapors that
can create a fire hazard or explosion.
• After starting a cycle, do not reach into the
washer until all motions stop.
• Do not tamper with the controls.
• The appliance is not intended for use by
young children or infirm persons without
supervision.
• If the supply cord is damaged, it must be
replaced by the manufacturer, or its service
agent or a similarly qualified person in order
to avoid a hazard.
• If the appliance is supplied from a cord
extension set or electrical portable outlet
device it should be positioned so that it is not
subjected to splashing or ingress of
moisture.
Understanding your responsibilities
• Do not use chlorine bleach and ammonia or acid(such as vinegar or rust remover) in the same
wash. Hazardous fumes can form.
• Unplug power supply cord before attempting to service your washer.
• Do not wash fiberglass material.
Small particles can stick to fabrics washed in following loads and cause skin irritation.
• Do not spray water on the control panel of the washer.
It could cause fire or an electric shock.
• In case of the dual valve model, if you connect only cold water inlet valve, while water
temperature is selected as hot or warm, there can be water leakage from unconnected water
inlet valve.
• This appliance must be grounded.
To avoide electrical shock, use a metal pipe for the ground connection.
3
INSTALLATION INSTRUCTIONS
Removing transit bolts
1. Before operating the washer, remove the
transit bolts(3ea) along with the rubber.
2. Unscrew the 3 bolts with the spanner
supplied. Keep the 3 bolts and spanner for
future use.
• If the bolts are not removed, it may cause
heavy vibration, noise and malfunction.
• Whenever the appliance is transported, the
transit bolts must be refitted.
3. Close the holes with the cap holders supplied.
Location of washer
• Check location where the washer will be installed. Make sure you have everything necessary for
correct installation.
• Do not place or store your washer below 0°C (32°F) to avoid any damage from freezing.
• Do not place or store laundry products on top of washer at any times.
Drain Hose
• Install the washer on the horizontal solid floor.
Washer
If the washer is installed on an unsuitable floor, it could make
considerable noise, vibrate severely and cause a malfunction. If the
washer is not level, adjust leg up or down for horizontal installation.
• Ventilation openings must not be obstructed by carpeting when the
Laundry
washer is installed on a carpeted floor.
Tub
• Leave some space (right & left : 2cm, rear : 10cm).
approx.
• In case of built-in installation, the distance between top of the washer
2cm
and bottom of upper plate should be at least 3mm.
4
INLET HOSE CONNECTION
The washer should be connected to the water mains using new hose sets and old hose sets
should not be reused.
In using only one water tap or in case of only one water inlet valve, connect the inlet hose to the
cold water inlet valve.
Option : Be careful not to confuse hot water inlet and cold water inlet.
For Ordinary Tap
1 Pull down the collar of the
inlet hose to separate it
from the water tap
adapter.
2 Loosen the four screws
properly in order to fit into
water tap.
3 Fit the water tap adapter
into the water tap and
tighten the four screws
evenly while pushing up
the adapter so that the
rubber packing can stick
to the water tap tightly.
TAPE
4 Remove the tape, and
screw connector B into
connect A tightly.
5 Connect the inlet hose to
the water tap adapter by
pulling down the collar of
the hose end.
Connector A
Connector B
6 Connect the inlet hose
adapter of the hose to the
water inlet of the washer
by turning it clockwise to
be fixed tightly.
• Please check the rubber
packing present inside the inlet
hose adapter of the hose.
For Screw-Shaped Tap
1 Connect the inlet hose to
the water tap by screwing
the connector tightly.
Connector
Hose
Rubber
Packing
Connector
2 Connect the connectorinlet supplied if necessary.
Connector
inlet
Connector
Hose
3Connect the inlet hose
adapter to the water inlet
of a washer and turn it to
be fixed.
Rubber
Packing
Connector
5
*Check the packing in the inlet
ELECTRICAL REQUIREMENTS
WARNING
Electrical shock hazard : Failure to follow these instructions could result in
death or serious injury.
• Electrical earth is required on this washer
• If it does not fit the outlet, have a proper outlet
installed by a qualified electrician.
• Don’t earth to a gas pipe.
• Don’t change the power supply cord plug.
• Check with a qualified electrician if you are not
sure the washer is properly earthed.
Recommended earthing method
C
B
A
For your personal safety, this washer must be earthed.
This washer is equipped with a power supply cord ‘A’ having a earthing plug ‘B’.
To minimize possible shock hazard, the cord must be plugged into a mating
earthing-type wall receptacle ‘C’. If a mating wall receptacle is not available,
it is the personal responsibility and obligation of the customer to have the
proper earthed wall receptacle installed by a qualified electrician.
Drain system
• Never forget to install drain hose before operating your washer.
• Open the packing box, and there is a drain hose inside the drum.
• Connect the drain hose to the drain outlet at the back side of the washer.
• Top of laundry tub must be at least 60cm high and no higher than 100cm from bottom of washer.
• When installing the drain hose to tub(sink), secure it tightly with a string.
• Proper securing of the drain hose will protect the floor from damage due to water leakage.
• When the drain hose is too long, do not force it back into the washer.
This will cause abnormal noise.
Level adjustment
1 If the washer is installed on an
unsuitable floor, it could make
considerable noise, vibrate and
cause a malfunction.
6
2 Adjust the level of washer using adjustable legs.
• Please check if there is any gap between the
four adjustable legs and the floor.
• Turning adjustable legs by the enclosed
spanner, adjust the level of washer and make
it sure that there is no swaying of washer.
• After the adjustment is finished, turn the fixing
nuts up tightly so that the washer maintains
the adjustment.
Fixing Nut
adjustable leg
3 Make it sure that the washer does not sway when you press
down the four corners of the washer's top plate.
NOTE
There should be no swaying of washer and all the
adjustable legs should stick to the floor closely.
OPERATING YOUR WASHER
To obtain the best washing results, you must operate your washer properly.
This section gives you this important information.
Preparing clothes for washing
• Close zippers, snaps, and hooks to avoid
snagging other items.
Remove pin, buckles, and other hard
objects to avoid scratching the washer
interior.
• Empty pockets and pull them inside out.
• Turn down cuffs and turn synthetic knits
inside out to avoid pilling.
• Tie strings and sashes to avoid tangling.
• Treat spots and stains.
(See “Removing stains” on page 21)
7
Sorting
• Separate heavily soiled items from lightly soiled ones, even if they would normally be washed
together.
• Separate dark colors from light colors, colorfast items from non-colorfast item.
Soil (Heavy, Normal, Light)
Color (White, Lignts, Darks)
Lint (Lint producers, Collectors)
Separate clothes according to amount of soil.
Separate white clothes from colored clothes.
Wash lint producers and lint collectors separately.
Loading
• Drop items into washer loosely. Items
should move easily through wash water for
best cleaning and wrinkle-free results.
• Load washer properly and select correct
load size setting.
Overloading and selecting a setting too
small for the wash load can :
- Cause poor cleaning
- Increase wrinkling
- Create excessive lint
- Wear out items faster (because of pilling)
• Mix large and small items in each load. Load
evenly to maintain washer balance.
An unbalanced load can make the washer
vibrate during spin.
• Reduce wash time when using a small load
size setting. Load with only a few small
items needs less wash time.
• Use a large load size setting to reduce
wrinkling with permanent press clothes and
some synthetic knits. These items should
have more room to move in the water than
heavy items. (towels, jeans)
Adding detergent
1 Detergent case
2 Adding fabric softener
• If desired, add measured liquid fabric
softener to the softener inlet.
• Pour liquid fabric softener into the
dispenser using the amount
recommended on the package.
• Do not exceed the maximum fill line.
Overfilling can cause early dispensing of the
fabric softener which could stain clothes.
• Do not open the detergent case when
water is supplied.
• Avoid pouring fabric softener directly on
the clothes.
Pre wash
Main wash
Fabric softener
8
THE FUNCTIONS OF THE CONTROL PANEL
Press this switch to turn the power on or off.
Operation and temporary stop is repeated as it is pressed.
When you want to change program in operating;
press the “Start/Hold” button → Select the program that you want to change → press the
“Start/Hold” button again.
You can select the course you want, and each lamp is turned on when that course is selected.
For the more detailed information, please refer to the page 11~18.
It can be used to adjust temperature of water according to types of the load to be washed.
As the button is pressed, temperature of water is selected by
Cold → 30˚C → 40˚C → 60˚C → 95˚C
By pressing the spin button, the spin speed can be chosen.
Rinse Hold
• Is selected by pressing the spin button repeatedly. This function leaves clothes
in the machine; suspended in the water after a rinse without entering into spin.
• To proceed through to a drain or spin, after the Rinse Hold function is
completed, use spin button.
No spin
• If no spin is selected, the washer stops after draining water.
Crease Care • If you want to prevent crease, select this button with spin speed.
Rinse+
• Is used to add a rinse, which may assist in removing traces of detergent residue.
• By selecting Rinse+ function, the rinse time and the rinse water are increased.
Pre-Wash
• The washer operates one additional wash and spin before the main wash.
• If the laundry is heavily soiled, Pre-Wash course is effective.
• Pre-Wash is available in Cotton and Synthetic programs.
All courses have pre-set washing times, but Time Save decreases it to 10 minutes.
Each time this button is pressed the watch icon is repeated on and off. When it is on, the Time
Save function is set. Time Save is available in Cotton, Eco and Synthetic programs.
It can be used to pre-engage time for wash.
Use this function when you want to protect any accident occurring from handling of washer by a child.
During an operation of washer, press ‘Time Save’ and ‘Time Delay’ buttons simultaneously.
In Child Lock mode, no button functions except Power button.
In Child Lock mode, press ‘Time Save’ and ‘Time Delay’ buttons simultaneously like setting Child
Lock and Child Lock is cancelled.
To change to the desirde program, while in Child Lock mode;
1. Press both the Time save and Time delay buttons together once again.
2. Press the Start/Hold button.
3. Select the desired program and press the Start/Pause button again.
Change
the desired
program
* The child lock can be set at any time and it is automatically cancelled when operational errors
occur. Also Child Lock works also when power is off.
9
WASHING PROCEDURE AND PROGRAM SELECTION
1. COTTON IS AUTOMATICALLY SELECTED UPON POWER ON
• Press the Power button to start.
• Press the Start/Hold button
• Initial condition
- Program : Cotton
- Wash : main wash
- Rinse : 3 times
- Spin : 800 rpm
- Water temperature : 40˚C
2. MANUAL SELECTING
• Press the Power button to start
• Select the conditions which you want to use by turning the program dial and pressing each button.
• Press the Start/Hold button.
3. RESERVED WASHING
• Reservation can be made from 2 hours to 12 hours.
example) To make reservation to complete washing in 8 hours.
- Procedure to press the button.
select the
program
or manual
ajust to "8"
* Each pressing of the button advances time delay by one hour.
• Now the reservation is made.
• If you want to check the selected program, press the “Start/Hold” button again.
• Preparing washing before starting “Time Delay”;
- Turn on the water tap
- Load laundry and close the door
- Place the detergent and fabric softener in the detergent case.
• To cancel the time delay, press the Power button.
10
4. FUNCTION
• Recommended programs according to the laundry type
Program
Cotton
Fabirc
Type
Proper
Temp.
Option
Maximum
Load
First check if laundry is machine
washable.(white cotton, linen
towel and sheets..)
60˚C
(95˚C)
Pre Wash
Rinse+
Crease Care
Rating
Colorfast garments
(shirts, night dresses, pajamas..)
and lightly soiled white cottons
(underwear..)
40˚C
(60˚C, 30˚C)
Pre Wash
Rinse+
Crease Care
Rating
Eco
Laundry type is the same as
Cotton.
60˚C
Pre Wash
Rinse+
Crease Care
Rating
Synthetic
Polyamide, Acrylic, Polyester
40˚C
(60˚C, 30˚C)
Pre Wash
Rinse+
Crease Care
Less than
1.5kg
Delicate
Delicate laundry easily
damaged
(silk, curtains..)
Cold
Rinse+
Crease Care
Less than
1.0kg
Machine washable woolens
with pure new wool only.
Cold
Rinse+
Crease Care
Less than
1.0kg
Cold
(30˚C)
Rinse+
Crease Care
Less than
1.0kg
30˚C
(Cold, 40˚C)
Rinse+
Crease Care
Less than
1.0kg
Wool
Hand Wash
Quick
“Hand wash” marked delicate
and wool laundry
Colored laundry which
is lightly soiled fast.
• Pre Wash : If the laundry is heavily soiled, “Pre Wash” program is recommended.
Pre Wash is available in Cotton and Synthetic programs.
• Rinse+ : Used to introduce an additional rinse, which may assist in removing traces of detergent residue.
• Eco : By selecting Eco function, the water temperature is lowered and washing time is increased.
So you can economize your consumption of heating energy.
11
* COTTON PROGRAM
1
Put the laundry in to the drum. Put detergent and softener into the detergent case.
Then close the door.
• Put detergent into the main wash and prewash compartments in the detergent case.
Softener should be below the ‘MAX’ level.
• Put detergent into the pre wash compartment only if you want to add prewash.
• When you want to use bleach, put it into the main wash compartment with detergent.
2
Press the Power button.
• The LED shows only ‘---’ and all Program Lights turn on.
3
Select the ‘Cotton’ program using program selection dial.
• If you press Start/Hold button after power button without selecting program, the
‘Cotton’ program is selected as default program.
• Washing temperature ‘40’ ˚C, spin ‘800’ rpm and rinse ‘3’ times are selected
automatically.
• If you want to change washing temperature, the spin velocity or add wash options
(Rinse+, Crease Care), press each button.
4
Press Start/Hold button.
• The Door is locked. By sensing the weight of laundry and supplying wash water,
The appliance starts washing.
Note
• If you want to change the setting during operation, press the Start/Hold button to hold the operation and
press the button you want.
• ‘30’, ‘40’, ‘60’ and ‘95’ ˚C washing temperatures are selectable with Cotton program.
• ‘Prewash’, ‘Rinse+’, and ‘Crease Care’ wash options are selectable with Cotton program.
Caution!
• If you select washing temperature ‘95’ ˚C, some cold water is supplied before the drain of main wash. This
is to protect the user from the hazard of burn injury by lowering the temperature of hot wash water instead
of directly draining it. Therefore this is not a malfuction.
(Be careful with the draining water, since it can be still hot although the temperature is lowered.)
12
* ECO PROGRAM
1
Put the laundry in the drum. Put detergent and softener into the detergent case. Then
close the door.
• Put detergent into the main wash and prewash compartments in the detergent
case. Softener should be below the ‘MAX’ level.
• Put detergent into the pre wash compartment only if you want to add prewash.
• When you want to use bleach, put it into the main wash compartment with
detergent.
2
Press the Power button.
• The LED shows only ‘---’ and all Program Lights turn on.
3
Select the ‘Eco’ program using program selection dial.
• Washing temperature ‘60’ ˚C, spin ‘800’ rpm and rinse ‘3’ times are selected
automatically.
• If you want to change the spin velocity or add wash options (Rinse+, Crease Care),
press each button.
4
Press Start/Hold button.
• The Door is locked. By sensing the weight of laundry and supplying wash water,
The appliance starts washing.
Note
• If you want to change the setting during operation, press the Start/Hold button to hold the operation and
press the button you want.
• Only ‘60’ ˚C washing temperature is selectable with Eco program.
• Only ‘Rinse+’ and ‘Crease Care’ of all wash options are selectable with Eco program.
13
* SYNTHETIC PROGRAM
1
Put the laundry in the drum. Put detergent and softener into the detergent case. Then
close the door.
• Put detergent into the main wash and prewash compartments in the detergent
case. Softener should be below the ‘MAX’ level.
• Put detergent into the pre wash compartment only if you want to add prewash.
• When you want to use bleach, put it into the main wash compartment with
detergent.
2
Press the Power button.
• The LED shows only ‘---’ and all Program Lights turn on.
3
Select the ‘Synthetic’ program using program selection dial.
• Washing temperature ‘40’ ˚C, spin ‘800’ rpm and rinse ‘3’ times are selected
automatically.
• If you want to change washing temperature, the spin velocity or add wash options
(Prewash, Rinse+, Crease Care), press each button.
4
Press Start/Hold button.
• The Door is locked. By sensing the weight of laundry and supplying wash water,
The appliance starts washing.
Note
• If you want to change the setting during operation, press the Start/Hold button to hold the operation and
press the button you want.
• Only ‘30’, ‘40’ and ‘60’ ˚C washing temperatures are selectable with Synthetic program.
• ‘Prewash’, ‘Rinse+’, and ‘Crease Care’ wash options are selectable with Synthetic program.
• The appropriate amount of laundry for Synthetic program is below 1.5kg.
14
* DELICATE PROGRAM
1
Put the laundry in the drum. Put detergent and softener into the detergent case. Then
close the door.
• Put detergent into the main wash and prewash compartments in the detergent
case. Softener should be below the ‘MAX’ level.
• Put detergent into the pre wash compartment only if you want to add prewash.
• When you want to use bleach, put it into the main wash compartment with
detergent.
2
Press the Power button.
• The LED shows only ‘---’ and all Program Lights turn on.
3
Select the ‘Delicate’ program using program selection dial.
• Washing temperature ‘Cold’, spin ‘400’ rpm and rinse ‘2’ times are selected
automatically.
• If you want to change the spin velocity or add wash options (Rinse+, Crease Care),
press each button.
4
Press Start/Hold button.
• The Door is locked. By sensing the weight of laundry and supplying wash water,
The appliance starts washing.
Note
• If you want to change the setting during operation, press the Start/Hold button to hold the operation and
press the button you want.
• Only ‘cold’ of washing temperature is selectable with Delicate program.
• ‘1000’ rpm of spin velocity is NOT selectable with Delicate program.
• Only ‘Rinse+’ and ‘Crease Care’ wash options are selectable with Delicate program.
• The appropriate amount of laundry for Delicate program is below 1.0kg.
15
* WOOL PROGRAM
1
Put the laundry in the drum. Put detergent and softener into the detergent case. Then
close the door.
• Put detergent into the main wash and prewash compartments in the detergent
case. Softener should be below the ‘MAX’ level.
• Put detergent into the pre wash compartment only if you want to add prewash.
• When you want to use bleach, put it into the main wash compartment with
detergent.
2
Press the Power button.
• The LED shows only ‘---’ and all Program Lights turn on.
3
Select the ‘Wool’ program using program selection dial.
• Washing temperature ‘Cold’, spin ‘400’ rpm and rinse ‘2’ times are selected
automatically.
• If you want to change the spin velocity or add wash options (Rinse+, Crease Care),
press each button.
4
Press Start/Hold button.
• The Door is locked. By sensing the weight of laundry and supplying wash water,
The appliance starts washing.
Note
• If you want to change the setting during operation, press the Start/Hold button to hold the operation and
press the button you want.
• Only ‘Cold’ washing temperature is selectable with Wool program.
• ‘1000’ rpm of spin velocity is NOT selectable with Hand program in order to protect damage on laundry.
• Only ‘Rinse+’ and ‘Crease Care’ wash options are selectable with Wool program.
• The appropriate amount of laundry for Wool program is below 1.0kg.
• Use only special detergent for wool.
(Since special neutral detergent for wool creates a lot of bubbles, use appropriate amount).
16
* HAND WASH
1
Put the laundry in the drum. Put detergent and softener into the detergent case. Then
close the door.
• Put detergent into the main wash and prewash compartments in the detergent
case. Softener should be below the ‘MAX’ level.
• Put detergent into the pre wash compartment only if you want to add prewash.
• When you want to use bleach, put it into the main wash compartment with
detergent.
2
Press the Power button.
• The LED shows only ‘---’ and all Program Lights turn on.
3
Select the ‘Hand Wash’ program using program selection dial.
• Washing temperature ‘Cold’, spin ‘400’ rpm and rinse ‘3’ times are selected
automatically.
• If you want to change the washing temperature, spin velocity or add wash options
(Rinse+, Crease Care), press each button.
4
Press Start/Hold button.
• The Door is locked. By sensing the weight of laundry and supplying wash water,
The appliance starts washing.
Note
• If you want to change the setting during operation, press the Start/Hold button to hold the operation and
press the button you want.
• Only ‘Cold’ and ‘30’ ˚C washing temperatures are selectable with Hand Wash program.
• ‘1000’ rpm of spin velocity is NOT selectable with Hand program.
• Only ‘Rinse+’ and ‘Crease Care’ wash options are selectable with Hand Wash program.
• Use Hand Wash program for the laundry that is marked ‘Hand wash’ in the care label.
17
* QUICK 30
1
Put the laundry in the drum. Put detergent and softener into the detergent case. Then
close the door.
• Put detergent into the main wash and prewash compartments in the detergent
case. Softener should be below the ‘MAX’ level.
• Put detergent into the pre wash compartment only if you want to add prewash.
• When you want to use bleach, put it into the main wash compartment with
detergent.
2
Press the Power button.
• The LED shows only ‘---’ and all Program Lights turn on.
3
Select the ‘Quick’ program using program selection dial.
• Washing temperature ‘30’ ˚C, spin ‘800’ rpm and rinse ‘2’ times are selected
automatically.
• If you want to change the washing temperature, spin velocity or add wash options
(Rinse+, Crease Care), press each button.
4
Press Start/Hold button.
• The Door is locked. By sensing the weight of laundry and supplying wash water,
The appliance starts washing.
Note
• If you want to change the setting during operation, press the Start/Hold button to hold the operation and
press the button you want.
• Only ‘Cold’, ‘30’ ˚C and ‘40’ ˚C washing temperatures are selectable with Quick 30 program.
• Only ‘Rinse+’ and ‘Crease Care’ wash options are selectable with Quick 30 program.
18
MAINTENANCE
Proper care of your washer can extend its life. This section explains how to care for your washer
properly and safely.
Cleaning your washer
Exterior
Interior
Wipe up detergent, bleach, and other spills with
a soft, damp cloth or sponge as they occur.
Occasionally wipe the outside of the washer to
keep its looking like new one.
Clean interior with 250ml of chlorine bleach
mixed with 500ml of detergent.
Run washer through a complete cycle.
Repeat this process if necessary.
Do not put sharp or metal object in your washer, or they
can damage the finish. Check all pockets for pins, clips,
money, bolts, nuts, etc.
Do not lay these objects in your washer after emptying
pockets.
Winter storage or moving care
Install and store your washer where it will not freeze. Because some water may stay in the
hoses, freezing can damage your washer.
If you store or move your washer during freezing weather, winterize it.
To winterize washer
To use washer again
• Turn off water faucet.
• Disconnect and drain water inlet hoses.
• Run washer on a drain and spin setting (see
page 10) for 1 minute.
• Unplug the power supply cord.
• Flush water pipes and hoses.
• Reconnect water inlet hoses.
• Turn on water faucet.
• Reconnect power supply cord.
Non-use or vacation care
Operate your washer only when you are at home.
If you are on vacation or don’t use your washer for an extended period of time, you should:
• Unplug the power supply cord or turn off eletrical power to the washer.
• Turn off the water supplier to the washer.
This helps avoid accidental flooding (due to a water pressure surge) while you are away.
19
HOW TO CLEAN THE FILTER
Cleaning the water inlet filter
• Clean the filter when water leaks from the water inlet.
1 Pull the power
plug out before
cleaning it.
2 Turn off the water
supply to the
washer and
separate the inlet
hose.
3 Pull the inlet filter
out.
4 Remove the dirt
from the inlet filter
with a brush.
Cleaning the drain filter
• This drain filter is used to screen the foreign stuffs such as threads, coins, pins, buttons etc..
• If the drain filter is not cleaned at proper time(every 10 times of use), drain problem could be
caused.
CAUTION : Be careful when draining if the water is hot.
1. Open the lower cover(1) by
using a coin. Remove the cap
hose(2) to pull out the hose.
2. Unplug the cap hose(2), allowing 3. Remove any foreign material
from the pump filter(3). After
the water to flow out. At this time
cleaning, turn the pump filter
use a vessel to prevent water
clockwise and insert the cap
flowing on to the floor. When water
does not flow any more, turn the
hose(2) to the original place.
pump filter(3) open to the left.
Close the lower cover.
100
3
1
2
3
2
Cleaning the detergent case
*After a while detergent and fabric softeners leave a deposit in the case;
- It should be cleaned from time to time with a jet of running water.
- If necessary it can be removed completely from the machine by pressing the catch downwards
and by pulling it out.
- To facilitate cleaning, the upper part of the fabric softener compartment can be removed.
*Detergent can also accumulate inside the recess which should be
cleaned occasionally with a brush.
*Once you have finished cleaning, replace the case and run a rinse
cycle without laundry.
20
REMOVING STAINS
Stained, heavily-soiled, or greasy items may need to be prewashed or soaked for best results.
Soaking helps remove protein-type stains like blood, milk or grass. Prewashing helps loosen soil
before washing.
Stain removal rules
• Use warm water for soaking or prewashing stained laundry. Hot water can set stains.
• Most stains are easier to remove when they are fresh.
• Before treating any stain, find out what kind of stain it is, how old the stain is, what kind of
fabric it is, and whether the fabric is colorfast. (Check the care label)
• Washing and drying can set some stains.
• Start with cold or warm water. Hot water can set some stains.
• When bleach is recommended, use a bleach that is safe for the fabric.
• Put the stained area face down on a paper towel or white cloth. Apply the stain remover to the
back of the stain. This forces the stain off fabric instead of through it.
Stain removal guide
STAIN
Blood
Chewing gum
Cocoa, Chocolate
Coffee
Cream/Milk
Ice cream
Deodorant
Egg
Fabric/Softener
Fruit stains
Grass
Grease and oil
Iron or rust
Lipstick
Mildew
Mud
Paint-oil based
Paint-water based
Scorch marks
TO REMOVE
Rinse immediately in COLD water.
If stain remains, soak in cold water with an enzyme prewash.
Use ice in plastic bag to harden the gum.
Scrape off what you can and the sponge with white spirits.
Sponge with COLD water and soak in an enzyme prewash.
If stains persist, rub in a little detergent and rinse in cold water.
Blot up quickly and rinse out in COLD water.
Rub in a little detergent and wash in the maximum temperature allowed for the
fabric type.
Rinse in COLD water and wash normally.
If stain is still apparent, sponge with white spirits.
Rub affected area with white vinegar and then rinse out in COLD water.
Sponge with white spirits.
Treat stiffened areas with enzyme prewash.
Soak in a COLD enzyme prewash, rinse and wash normally.
Rub affected area with bar soap and wash normally.
Treat as soon as possible by sponging with COLD water.
Rub a little detergent on the stain and wash normally.
Sponge with white spirits.
Rub in an enzyme prewash and wash as normally.
Lay the affected area face down on an absorbent cloth and work from the back.
Sponge with white spirits or dry cleaning fluid. Wash normally.
Apply lemon juice and salt and place in the sun. Wash normally.
Sponge with white methylated spirits and wash normally.
Wash in WARM water and detergent.
Moisten area with lemon juice, dry in the sun and wash normally.
If stain persists and the fabric allows, use a bleach.
Brush off any dry mud. Rinse in cold water.
If stain persists rub in a little detergent and wash normally.
Scrape off any fresh paint and sponge with a non flammable dry cleaning fluid
and wash normally.
Treat while still wet, rinse in WARM water and wash normally.
Dampen a cloth with hydrogen peroxide, lay it over the affected area and press
with a fairly hot iron.
21
TROUBLE SHOOTING
Most problems are easily solved if you understand the cause.
Check the following list for problem before calling for service.
If error mode such as IE, OE, UE were displayed on the control part, in this case, how to solve
these problem is first open and close the door, and then press START/HOLD button.
PROBLEM
CHECK POINT
• The washer will not
operate at all.
• Is there a power failure?
• Is the power cord correctly connected to an electric outlet?
• Did you turn on the power?
• Did you press Start/Hold button?
• Is there correct amount of laundry in the washer.
• Water is not supplied
• Did you connect the inlet hose and open the water tap?
• Is the inlet hose or the water tap frozen?
• Is the water supply shot off?
• Is there any foreign matter blocking up the inlet hose filter?
Error display
• The washer will not drain
Error display
• The washer will not spin
Error display
• Vibrating and too noisy
• Is the drain hose frozen or blocked up by dirt?
• Is the drain hose kinked or deformed?
• Is the end of the drain hose immersed in water?
• Is there excessive dirt inside the drain filter?
• Is the clothes in the drum collected on one side?
• Is the washer installed on an uneven floor or is the vibration
serious?
• Is the door open? (The lamp “ ” will light up in this case.)
• Is the washer installed on an uneven floor?
• Have all the transit bolts removed?
These cases are not malfunctions;
• The sound “wing” heard during water supply is the operating sound made by the water inlet valve.
• The sound “sha” heard in stopping the tub is the sound that comes from the autobalbancer of the tub.
22
SPECIFICATION
MODEL
DWD-F1011/F1012/F1013
DWD-F1211/F1212/F1213
Dimension (mm)
595 x 540 x 850 (WxHxD)
Maximum mass of textile (kg)
6.0
Unit Weight (kg)
64(Net) / 68(Gross)
Standard Water Consumption
50 l
Spin Speed (RPM)
Operating Water Pressure
No Spin/400/800/1000
No Spin/400/800/1200
0.03MPa ~ 0.8MPa (0.3kgf/cm2 ~ 8kgf/cm2)
WIRING DIAGRAM
23
English
Português
Disposal of Used Electrical & Electronic Equipment
Eliminação de Equipamento Eléctrico e
Electrónico Usado
The meaning of the symbol on the product, its
accessory or packaging indicates that this product shall
not be treated as household waste. Please, dispose of
this equipment at your applicable collection point for
the recycling of electrical & electronic equipments
waste. In the European Union and Other European
countries which there are separate collection systems
for used electrical and electronic product. By ensuring
the correct disposal of this product, you will help
prevent potentially hazardous to the environment and
to human health, which could otherwise be caused by
unsuitable waste handling of this product. The
recycling of materials will help conserve natural
resources. Please do not therefore dispose of your old
electrical and electronic equipment with your
household waste. For more detailed information about
recycling of this product, please contact your local city
office, your household waste disposal service or the
shop where you purchased the product.
Deutsch
O símbolo no aparelho, nos seus acessórios ou na
embalagem indica que este aparelho não deve ser
tratado como resíduos domésticos. Deixe deste
aparelho no ponto de recolha de material eléctrico e
electrónico para reciclagem mais perto de si. Na
União Europeia e noutros países europeus existem
sistemas de recolha separada para produtos eléctricos
e electrónicos usados. Garantindo uma eliminação
correcta deste aparelho, ajudará a evitar possíveis
danos ambientais e/ou pessoais, que um incorrecto
tratamento do aparelho usado poderia provocar. A
reciclagem de materiais ajuda a conservar os
recursos naturais. Por isso, não deite fora os
aparelhos eléctricos e electrónicos junto com os seus
resíduos domésticos. Para informação detalhada
sobre a reciclagem deste aparelho, contacte a sua
Câmara Municipal, o seu serviço de recolha de lixo
ou a loja onde comprou o aparelho.
Nederlands
Entsorgung von gebrauchten elektrischen und
elektronischen Geräten (Anzuwenden in den
Ländern der Europäischen Union und anderen
europäischen Ländern mit einem separaten
Sammelsystem für diese Geräte)
Verwijdering van Oude Elektrische en
Elektronische Apparaten (Toepasbaar in de
Europese Unie en andere Europese landen met
gescheiden ophaalsystemen)
Het symbool op het product of op de verpakking
wijst erop dat dit product niet als huishoudafval mag
worden behandeld. Het moet echter naar een plaats
worden gebracht waar elektrische en elektronische
apparatuur wordt gerecycled. Als u ervoor zorgt dat
dit product op de correcte manier wordt verwijderd,
voorkomt u mogelijk voor mens en milieu negatieve
gevolgen die zich zouden kunnen voordoen in geval
van verkeerde afvalbehandeling. De recyclage van
materialen draagt bij tot het vrijwaren van natuurlijke
bronnen. Voor meer details in verband met het
recyclen van dit product, neemt u het best contact op
met de gemeentelijke instanties, het bedrijf of de
dienst belast met de verwijdering van huishoudafval
of de winkel waar u het product hebt gekocht.
Das Symbol auf dem Produkt oder seiner
Verpackung weist darauf hin, dass dieses Produkt
nicht als normaler Haushaltsabfall zu behandeln ist,
sondern an einer Annahmestelle für das Recycling
von elektrischen und elektronischen Geräten
abgegeben werden muss. Durch Ihren Beitrag zum
korrekten Entsorgen dieses Produkts schützen Sie die
Umwelt und die Gesundheit Ihrer Mitmenschen.
Umwelt und Gesundheit werden durch falsches
Entsorgen gefährdet. Materialrecycling hilft den
Verbrauch von Rohstoffen zu verringern. Weitere
Informationen über das Recycling dieses Produkts
erhalten Sie von Ihrer Gemeinde, den kommunalen
Entsorgungsbetrieben oder dem Geschäft, in dem Sie
das Produkt gekauft haben.
Español
French
Eliminación de equipamiento eléctrico y
electrónico usado
Este símbolo en el producto, sus accesorios o
embalaje indica que el producto no debe tratarse
como un residuo doméstico. Deshágase de este
equipamiento en su punto de recogida más cercano
para el reciclaje de residuos eléctricos y electrónicos.
En la Unión Europea y otros países europeos existen
diferentes sistemas de recogida de productos
eléctricos y electrónicos usados. Al asegurar la
correcta eliminación de este producto ayudará a
evitar riesgos potenciales para el medio ambiente y la
salud de las personas que podrían tener lugar si el
producto no se eliminara de forma adecuada. El
reciclaje de materiales ayudará a conservar los
recursos naturales. Por consiguiente, no elimine
equipamiento eléctrico y electrónico usado junto con
residuos domésticos. Para información más detallada
acerca del reciclaje de este producto, póngase en
contacto con su oficina municipal, el servicio de
eliminación de residuos domésticos o el
establecimiento donde adquirió el producto.
Traitement des appareils électriques et
électroniques en fin de vie (applicable dans les
pays de l’union européenne et aux autres pays
européens disposant de systèmes de collecte
sélective).
Ce symbole, apposé sur le produit ou sur son
emballage, indique que ce produit ne doit pas être
traité avec les dechets ménagers. Il doit être remis à
un point de collecte approprié pour le recyclage des
équipements électriques et électroniques. En
s’assurant que ce produit est bien mis au rebus de
manière appropriée, vous aiderez à prévenir les
conséquenses négatives potentielles pour
l’environnement et la santé humaine. Le recyclage
des matériaux aidera à conserver les ressources
naturelles. Pour toute iformation supplémentaire au
sujet du recyclage de ce produit, vous pouvez
consulter votre municipalité, votre déchetterie ou le
magasin où vous avez acheté le produit.
»esky
Italiano
Likvidace pouûûit˝˝ch elektrick˝˝ch a elektronick˝˝ch za¯¯ízení
Trattamento del dispositivo elettrico od
elettronico a fine vita (Applicabile in tutti i paesi
dell’Unione Europea e in quelli con sistema di
raccolta differenziata)
Tento symbol na v˝robku, jeho p¯ísluöenství nebo obalu
oznaËuje, ûe s tímto v˝robkem nesmí b˝t zacházeno jako s
domovním odpadem. V˝robek zlikvidujte jeho p¯edáním
na sbÏrné místo pro recyklaci elektrick˝ch a elektronick˝ch
za¯ízení. V zemích evropské unie a jin˝ch evropsk˝ch
zemích existují samostatné sbÏrné systémy pro
shromaûÔování pouûit˝ch elektrick˝ch a elektronick˝ch
v˝robk˘. ZajiötÏním jejich správné likvidace pom˘ûete
prevenci vzniku potenciálních rizik pro ûivotní prost¯edí a
lidské zdraví, která by mohla vzniknout nesprávn˝m
zacházením s odpady. Recyklace odpadov˝ch materiál˘
napomáhá udrûení p¯írodních zdroj˘ surovin - z
uvedeného d˘vodu nelikvidujte prosím vaöe stará
elektrická a elektronická za¯ízení s domovním odpadem.
Pro získání podrobn˝ch informací k recyklaci tohoto
v˝robku kontaktujte prosím pracovníka ochrany ûivotního
prost¯edí místního (mÏstského nebo obvodního) ú¯adu,
pracovníky sbÏrného dvora nebo zamÏstnance prodejny,
ve které jste v˝robek zakoupili.
Questo simbolo sul prodotto o sulla confezione
indica che il prodotto non deve essere considerato
come un normale rifiuto domestico, ma deve invece
essere consegnato ad un punto di raccolta
appropriato per il riciclo di apparecchi elettrici ed
elettronici. Assicurandovi che questo prodotto sia
smaltito correttamente, voi contribuirete a prevenire
potenziali conseguenze negative per l’ambiente e per
la salute che potrebbero altrimenti essere causate dal
suo smaltimento inadeguato. Il riciclaggio dei
materiali aiuta a conservare le risorse naturali. Per
informazioni piú dettagliate circa il riciclaggio di
questo prodotto, potete contattare l’ufficio comunale,
il servizio locale di smaltimento rifiuti oppure il
negozio dove l’avete acquistato.
Poland
Slovensky
´tu
Utylizacja niepotrzebnego sprz´
elektrycznego i elektronicznego
Likvidácia pouûûit˝˝ch elektrick˝˝ch a elektronick˝˝ch
zariadení
Taki symbol na produkcie lub na jego opakowaniu
oznacza, Œe produkt nie moŒe byç traktowany jako
odpad komunalny, lecz powinien byç dostarczony do
odpowiedniego punktu zbiórki sprz´tu elektrycznego i
elektronicznego, w celu przerobu i odzysku odpadów.
W krajach Unii Europejskiej i w pozosta¬ych krajach
europejskich så odr´bne systemy segregacji
odpadów przeznaczone do utylizacji sprz´tu
elektrycznego i elektronicznego.
Przez takie pro ekologiczne zachowanie zapobiegajå
Pa˜stwo potencjalnym negatywnym wp¬ywom na
ßrodowisko naturalne oraz na zdrowie ludzi, jakie
mog¬yby wyståpiç w przypadku niew¬aßciwego
procesu sk¬adowania tego produktu. Przez
zagospodarowanie materia¬ów oszcz´dzamy równieŒ
surowce naturalne. Aby uzyskaç bardziej
szczegó¬owe informacje na temat przerobu i odzysku
materia¬ów elektronicznych z tego produktu, prosz´
skontaktowaç si´ z urz´dem miasta lub gminy,
lokalnym zak¬adem utylizacji sprz´tu elektrycznego i
elektronicznego lub ze sklepem, w którym produkt
zosta¬ zakupiony.
Tento symbol na v˝robku, jeho prísluöenstve alebo
obale oznaËuje, ûe sa s t˝mto v˝robkom nesmie
zaobchádzaù ako s domov˝m odpadom. V˝robok
zlikvidujte jeho odovzdaním na zbernom mieste pre
recykláciu elektrick˝ch a elektronick˝ch zariadení. V
krajinách európskej únie a v in˝ch európskych
krajinách existujú samostatné zberné systémy pre
zhromaûÔovanie pouûit˝ch elektrick˝ch a
elektronick˝ch v˝robkov. Zaistením ich správnej
likvidácie pomôûete prevencii vzniku potenciálnych
rizík pre ûivotné prostredie a æudské zdravie, ktoré by
mohli vzniknúù nesprávnym zaobchádzaním s
odpadmi. Recyklácia odpadov˝ch materiálov
napomáha udrûaniu prírodn˝ch zdrojov surovín – z
uvedeného dôvodu nelikvidujte prosím vaöe staré
elektrické a elektronické zariadenia s domov˝m
odpadom.
Pre získanie potrebn˝ch informácií k recyklácii tohto
v˝robku kontaktujte prosím pracovníka ochrany
ûivotného prostredia miestneho (mestského Ëi
obvodného) úradu, pracovníkov zberného dvora alebo
zamestnancov predajne, v ktorej ste v˝robok zakúpili.
Magyar
Slovensko
Feleslegessé vált elektromos és elektronikus
készülékek hulladékként való eltávolítása
(Használható az Európai Unió és egyéb európai
˚jtési rendszereiben)
országok szelektív hulladékgy˚
Ez a szimbólum a készüléken vagy a csomagolásán
azt jelzi, hogy a terméket ne kezelje háztartási
hulladékként. Kérjük, hogy az elektromos és
elektronikai hulladék gy˚jtésére kijelölt gy˚jtıhelyen
adja le. A feleslegessé vált termékének helyes
kezelésével segít megelızni a környezet és az emberi
egészség károsodását, mely bekövetkezhetne, ha
nem követi a hulladék kezelés helyes módját. Az
anyagok újrahasznosítása segít a természeti
erıforrások
megırzésében.
A
termék
újrahasznosítása érdekében további információért
forduljon a lakóhelyén az illetékesekhez, a helyi
hulladékgy˚jtı szolgáltatóhoz vagy ahhoz az
üzlethez, ahol a terméket megvásárolta.
Oddaja stare elektriËËne in elektronske opreme
(veljavno v evropski uniji in ostalih evropskih
drûavah s sistemom zbiranja loËËenih odpadkov)
»e se na izdelku ali a njegovi embalaûi nahaja ta
simbol, pomeni, da z izdelkom ne smete ravnati
enako kot z drugimi gospodinjskimi odpadki. Morate
ga oddati na ustrezno zbirno mesto za recikliranje
elektriËne in elektronske opreme. S pravilno oddajo
tega izdelka boste pomagali prepreËiti negativne
posledice na okolje in zdravje ljudi, do katerih bi
priölo v primeru neustreznega ravnanja ob odstranitvi
tega izdelka. Recikliranje materiala bo pripomoglo k
ohranjevanju naravnih virov. Podrobnejöe informacije
o reciklitanju tega izdelka lahko dobite pri lokalni
mestni upravi, sluûbi oddajanja gospodinjskih
odpadkov ali v trgovini, kjer ste izdelek kupili.
Odpadno elektriËno in elektronsko opremo lahko
oddate brezplaËno tudi distributerju neposredno ob
dobavi elektriËne oz. elektronske opreme.
Svenska
Dansk
Omhändertagande av gamla elektriska och
elektroniska produkter (Användbar i den
Europeiska Unionen och andra Europeiska
länder med separata insamlingssystem)
Håndtering af udtjente elektriske og elektroniske
produkter (Gælder for den Europæiske Union og
andre europæiske lande med separate
indsamlingssystemer)
Symbolen på produkten eller emballaget anger att
produkten inte får hanteras som hushållsavfall. Den
skall i stället lämnas in på uppsamlingsplats för
återvinning av el- och elektronikkomponenter.
Genom att säkerställa att produkten hanteras på rätt
sätt bidrar du till att förebygga eventuellt negativa
miljöoch hälsoeffekter som kan uppstå om produkten
kasseras som vanligt avfall. Återvinning av material
hjälper till att bibehålla naturens resurser. För
ytterligare om återvinning bör du kontakta lokala
myndigheter eller sophämtningstjänst eller affären där
du köpte varan.
Dette symbol på produktet eller emballagen angiver,
at produktet ikke må behandles som
husholdningsaffald. Det skal i stedet indleveres på en
deponeringsplads specielt indrettet til modtagelse og
oparbejdning af elektriske og elektroniske produkter.
Ved at sikre at produktet bortskaffes korrekt,
forebygges de eventuelle negative miljø-og
sundhedsskadelige påvirkninger, som en ukorrekt
affaldshåndtering af produktet kan forårsage.
Genindvinding af materialer vil medvirke til at bevare
naturens ressourcer. Yderligere information om
genindvindingen af dette produkt kan fås hos
myndighederne, det lokale renovationsselskab eller
butikken, hvor produktet blev købt.
Norsk
Avhending av gamle elektriske og elektroniske
apparater (gjelder i den Europeiske Unionen og
andre europeiske land med separat
innsamlingssystem)
Dette symbolet på produktet eller innpakningen
indikerer at dette produktet ikke må håndteres som
husholdningsavfall. I stedet skal det leveres inn til
spesielt innsamlingspunkt for gjenvinning av det
elektriske og elektroniske utstyret. Ved å sørge for at
dette produktet avhendes på korrekt måte, vil du
hjelpe til med å forhindre potensielle negative
påvirkninger på miljøet og helse, som ellers kan være
resultatet av feilaktig avfallshåndtering av dette
produktet. Gjenvinning av disse materialene vil
hjelpe til med å ta vare på våre maturressurser. For
mer informasjon om gjenvinning av dette produktet,
kan du kontakte lokale myndigheter.
Suomi
Käytöstä poistetun sähkö-ja
elektroniikkalaitteen hävitys (Euroopan Unioni
ja muiden Euroopan maiden keräysjärjestelmät)
Symboli, joka on merkitty Tuotteeseen tai sen
pakkaukseen, osoittaa, että tätä tuotetta ei saa
käsitellä talousjätteenä. Tuote on sen sijaan
luovutettava sopivaan sähkö-ja elektroniikkalaitteiden
kierrätyksestä huolehtivaan keräyspisteeseen. Tämän
tuotteen asianmukaisen hävittämisen varmistamisella
autetaan estämään sen mahdolliset ympäristöön ja
terveyteen kohdistuvat haittavaikutukset, joita voi
aiheutua muussa tapauksessa tämän tuotteen
epäasianmukaisesta jätekäsittelystä. Materiaalien
kierrätys säästää luonnonvaroja. Tarkempia tietoja
tämän tuotteen kierrättämisestä saa paikallisesta
kunnantoimistosta.
ABOUT THIS MANUAL
VISION CREATIVE, INC.
서울 종로구 통의동 6번지
이룸빌딩4층
담
당
박선정님
TEL
MODEL
DWD-F1011N/1012N/1013N/1211N/1212N/1213N’S
BUYER
(DEER)-불가리향_DWD-F1011/1012/1013/1211/1212/1213’S
일
정
제
판
규
격
MEMO
1차
6차
2차
7차
3차
8차
4차
9차
5차
10차
인쇄
동일
05.5.19-영어(Basic)으로 작업함
연락처
VISION 담 당
전지현
TEL: 730-0660 FAX: 730-3788