User guide | Datalogic Scanning QS6500BT Barcode Reader User Manual

Condenser dryer
DE60F60NW1 model
Installation instructions
and User guide
AU
Contents
1
Safety and warnings
2
Installation instructions
4
Before drying
6
Selecting a programme and operating your machine
7
Maintenance and cleaning
12
Troubleshooting
14
Manufacturer’s Warranty
16
Customer Care
17
Caution, risk of fire – this is a safety symbol.
Failure to follow the warnings outlined in these user instructions can cause
a fire hazard.
Important! SAVE THESE INSTRUCTIONS
The models shown in this User Guide may not be available in all markets and are
subject to change at any time. For current details about model and specification
availability in your country, please visit our local website listed on the back cover
or contact your local Fisher & Paykel dealer.
2
Safety and warnings
WARNING!
Fire Hazard
Please read the following information. Otherwise, there may be the
risk of personal injury or material damage. Moreover, any warranty
and reliability commitment will become void.
General safety
ƒƒ Never place your machine on a carpet covered floor. The lack of airflow from below your
machine may cause electrical parts to overheat.
ƒƒ Your machine is designed to stop operating in the event of power resuming after a power failure.
You must press Start/Pause/Cancel button to resume the programme.
Press the Start/Pause/Cancel button for 3 seconds to cancel the programme (see, ‘Ending the
programme through cancelling’ page 11).
ƒƒ Your machine can be operated at temperatures between +5°C and +35°C.
ƒƒ This appliance is not intended for use by persons (including young children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision on instruction concerning the use of the appliance by a person
responsible for their safety.
First use
 When operating your machine for the first time, partly load it with wet items of clothing and let
it run approximately for 15 minutes.
ƒƒ You may smell an unpleasant odour and excessive fibre/lint may accumulate during first
drying cycle.
ƒƒ For safety and performance purposes, clean the filters after each drying cycle.
Intended use
ƒƒ
ƒƒ
ƒƒ
ƒƒ
This product has been designed for home use.
The appliance may only be used for drying textiles that are marked accordingly.
Do not operate this product without the lint filter in place.
Do not dry unwashed items in the dryer.
Safety instructions
Unplug the machine when it is not in use.
Never wash down the appliance with water. There is the risk of electric shock!
Never touch the plug with wet hands.
Never pull from the cable to unplug the machine.
Do not operate the machine if the power cord or plug is damaged.
Never attempt to repair the machine yourself.
For malfunctions that cannot be solved by information in the User Guide:
Turn off and unplug the appliance and contact a Fisher & Paykel Authorised Repairer.
ƒƒ Lint must not be allowed to accumulate around the tumble dryer.
ƒƒ
ƒƒ
ƒƒ
ƒƒ
ƒƒ
ƒƒ
ƒƒ
Safety and warnings
3
To minimise the risk of fire in a tumble dryer, the following should be observed:
Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol,
kerosene, dry cleaning solvents, spot removers, turpentine, waxes or wax removers, should be
washed in hot water with an extra amount of detergent before being dried in the tumble dryer.
Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as
in a tumble dryer. The items become warm, causing an oxidation reaction in the oil. Oxidation
creates heat. If the heat cannot escape, the items can become hot enough to catch fire. Piling,
stacking or storing oil-affected items can prevent heat from escaping and so create a fire hazard.
If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated
by hair care products be placed in a tumble dryer they should first be washed in hot water with
extra detergent - this will reduce, but not eliminate, the hazard.
The ‘cool down’ cycle of tumble dryers should be used to reduce the temperature of the items to
ensure they will not be damaged. They should not be removed from the tumble dryer or piled or
stacked while hot.
Important!
Never stop the tumble dryer before the end of the drying cycle unless all items are quickly
removed and spread out so that the heat can dissipate.
ƒƒ The dryer should not be used for items cleaned using industrial chemicals.
ƒƒ Items containing foam rubber (also known as latex foam) or similarly textured rubber like
materials should not be dried in a tumble dryer.
ƒƒ Foam rubber materials can, when heated, produce fire by spontaneous combustion.
ƒƒ Fabric softeners or similar products should not be used in a tumble dryer to eliminate the effects
of static electricity unless this practice is specifically recommended by the manufacturer of the
fabric softener or product.
ƒƒ Undergarments that contain metal reinforcements should not be placed in a tumble dryer.
Damage to the tumble dryer can result if metal reinforcements come loose during drying.
ƒƒ Plastic articles such as shower caps and waterproof textiles should not be placed in a tumble
dryer.
ƒƒ Rubber-backed articles, fibreglass, clothes fitted with foam rubber pads, pillows, galoshes and
rubber-coated tennis shoes should not be placed in a tumble dryer.
If there are children in your house...
ƒƒ Electrical appliances may be dangerous for children. Keep children away from the machine when
it is operating. Do not let them tamper with the machine.
ƒƒ Close the loading door when you leave the area where the machine is located.
ƒƒ Young children should be supervised to ensure that they do not play with the appliance.
4
Installation instructions
Technical specifications
Specification
Height / Height for built-under installation (mm)
850 / 820
Width (mm)
595
Depth / Depth for built-under installation (mm)
540
Height adjustment of feet (mm)
Length of drain hose (mm)
5
1400
Diameter of drain hose (mm)
10
Highest point of the hose (mm)
800
Weight, unpacked
Voltage
36
220 – 240V, 50 Hz
Connected load
2000 – 2200 W
Fuse protection
16A
The proper location
ƒƒ Install your machine in environments which have no risk of freezing and in a stable and level
position.
ƒƒ Do not install the machine behind lockable door, a sliding door, or a door that is hinged on the
opposite side to that of the dryer, in such a way that the door of the machine cannot be opened fully.
ƒƒ Do not place your machine on a carpet covered floor, a long pile rug or on similar surfaces.
ƒƒ Operate your machine in a well ventilated, dust-free environment.
ƒƒ Make sure that your machine is not placed on the power cable.
Place it at least 30 mm away from the edges of other furniture and walls.
Place the machine on a sound floor.
ƒƒ A special part (Part No. 791746) must be used if the machine is to be installed under a counter or
in a cupboard. This replaces the top trim and must be installed by a Fisher & Paykel Authorised
Repairer. Never operate the machine without the top trim.
ƒƒ If the machine is to be placed on top of a washing machine, the approximate weight together
may reach 180 kg when they are full.
A stacking kit should be used between the products, fitted to the washing machine.
Stacking Kit White Part No. 790691
Levelling
In order to ensure that your machine operates quietly and vibration-free, it must stand level and
balanced on its feet.
Balance the machine by adjusting the front feet. Loosen the feet by hand, and adjust them until
the machine stands level and does not rock.
ƒƒ Never unscrew the adjustable feet from their housings.
Two plastic pieces supplied with the Installation Instructions and User Guide
prevent your machine from slipping on wet and slippery surfaces. Tilt your
machine backwards to install these plastic parts. Fit the plastic parts to the
front adjustable feet. Press on the plastic parts to fix them in their places. Check
the balance of your machine again and readjust the adjustable feet if necessary.
Fig.1 Fitting the
non-slip foot caps
Installation instructions
5
Electrical connection
Connect the machine to an earthed outlet protected by a fuse of suitable capacity.
Important!
 Connection should comply with national regulations.
 Power cord plug must be within easy reach after installation.
 The voltage and the allowed fuse protection are specified in the section ‘Technical specifications’
(page 4).
The stated voltage must match with your mains voltage.
Connection via extension cords or multi-plugs should not be made.
The main fuse and switches must have a contact distance of minimum 3 mm.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
 The appliance must not be operated unless it is repaired! There is the risk of electric shock!




Products equipped with a condenser unit accumulate water during the drying cycle, which is
collected in the water tank. The accumulated water should be drained after each drying cycle.
Connection to a water drain
The Tank Full warning LED will light up at the end of
each programme.
You can directly send the accumulated water out
through the water drain hose supplied with the machine
instead of periodically draining the water collected in
the water tank.
Connecting the water drain hose:
1 Remove the hose on the machine by pulling it out from
its end. Do not use any tools to take out the hose.
Attach the drain hose adaptor to the end of this hose.
2 Connect the special drain hose supplied with the
machine to the hose adaptor fitting.
3 The other end of the drain hose can be directly
connected to the wastewater drain or to the washbasin.
The fitting must always be secured in all types of
connections. Your house may be flooded if the hose gets
out of its housing during water discharge.
Important!
Fig.2 Connecting to a water drain
 The hose should be attached to a maximum height of 800 mm.
 You must be careful not the pinch or bend the hose.
 The end of the hose should not be bent, it should not be stepped on and it must not be folded
between the drain and the machine.
6
Before drying
Always follow the advice on the garment labels. With this dryer, dry only items where the label
states that they are suitable for drying in a dryer by selecting the appropriate programme.
Fig.3 Garment care indicators
ƒƒ Laundry items with metal attachments such as belt buckles and metal buttons can damage
your machine.
ƒƒ Do not dry items such as woollen, silk garments and nylon stockings, delicate embroidered
fabrics, garments with metal accessories and items such as sleeping bags in the machine.
ƒƒ Garments made of delicate and valuable fabrics as well as lace curtains can be creased. Do not
dry these in your machine!
ƒƒ Do not dry items made of hermetic fibres such as pillows and quilts in the dryer.
ƒƒ Do not dry clothes containing rubber in the machine.
ƒƒ Do not dry clothes which have been exposed to petroleum, oil, combustible or explosive agents
in the machine even if they are washed beforehand.
ƒƒ Overly wet laundry or laundry that is dripping water must not be put into the machine.
Preparing clothes to be dried
ƒƒ All laundry must be spun at the highest possible spin speed your washing machine allows for the
textile type.
ƒƒ Laundry may be tangled after washing. Separate items before placing them into your dryer.
ƒƒ Sort your laundry according to their types and thicknesses. Dry the same kinds of items together.
Correct load capacity
ƒƒ The maximum capacity of the dryer is 6 kg.
ƒƒ Adding laundry to the machine more than the level shown in Fig.4 is
not recommended.
The drying performance of the product will decrease when the machine
is overloaded.
ƒƒ Overloading may also cause damage to the product and your clothes.
ƒƒ Place your garments into the drum loosely so that they will not get tangled.
ƒƒ Large pieces may bunch-up during drying. Stop the machine 1 – 2 times
during the drying process to separate bunched-up laundry.
Fig.4 Loading the laundry
Loading door
Open the loading door. Place laundry items loosely into the machine. Push the loading door to
close. Ensure that no items are caught in the door.
Selecting a programme and operating your machine
Control panel
6
Fig.5 Control panel features
1
2
3
4
On/Off button
Programme selection knob
Start/Pause/Cancel button
Cancel Audio Warning
5
4
3
2
1
7
5 Programme follow-up indicator
6 CLEAN FILTER warning LED
7 TANK FULL warning LED
Turning the machine on
Prepare the machine for programme selection by pressing the On/Off button.
Pressing the On/Off button does not necessarily mean the programme has started.
Press the Start/Pause/Cancel button to allow the machine to start the programme.
Programme selection
Choose the appropriate programme from the table below. Select the desired programme with
the programme selection button.
Extra dry
Dry at high temperature only for cotton laundry. Thick and multi-layered
laundry (eg: towels, linens, jeans) are dried in a way that they do not
require ironing.
Ready to Wear
Normal laundry (eg: tablecloths, underwear) are dried in a way that they
do not require ironing before placing in drawers.
Ready to Iron
Normal laundry (eg: shirts, dresses) are dried ready to be ironed.
Always select the highest temperature that is safe for the type of items in the load (check care
labels). A higher temperature will ensure energy and time saving, but may be unsuitable for
some items and cause damage.
7
8
Selecting a programme and operating your machine
Main programmes
Depending on the type of textile, the following main programmes are available:
Cottons
You can dry your durable clothes with this programme as it dries at a higher temperature.
It is recommended to use for your cotton items (such as bed sheets, quilt cover,
underclothing, etc).
Synthetics
You can dry your less durable clothes with this programme, as it dries at a lower temperature
compared to the cottons programme. It is recommended for your synthetic clothes (such as
shirts, blouses, synthetic/cotton blended garments, etc).
Do not dry curtains and lace in your machine.
Wrinkle Guard
A two-hour Wrinkle Guard programme to prevent laundry from creasing will be activated if you
do not take the laundry out after the programme has come to an end. This programme rotates
the laundry in 60-second intervals to prevent creasing.
Delicates
A lower temperature for your very delicate laundry (silk blouses, fine underwear, etc) that is
suitable for tumble drying or laundry which is recommended to be hand-washed.
Freshen up
This 10 minute airing cycle blows cool air through your clothes. It is used to freshen clothes and
deodorise unpleasant odours on items that have been kept in closed environments for long
periods.
Timed programmes
Select one of the 10 min, 20 min, 40 min and 60 min timed programmes to achieve the desired
final drying level at low temperatures. The machine dries for the selected time regardless of
the level of moisture in your clothes. It is important to check the clothes throughout the longer
timed programmes to avoid overdrying.
Selecting a programme and operating your machine
9
Auxiliary function
Buzzer cancel
Your machine will send out a buzzer warning when the programme comes to an end. If you
do not want to hear this warning, you need to press the Buzzer cancel button. The relevant
LED will light up when this button is pressed and an audio warning will not be given when the
programme comes to an end.
Filter cleaning
A warning LED will light up to remind you to clean the filter after the programme finishes.
If the filter cleaning warning LED lights up continuously, please refer to the ‘Troubleshooting’
section (page 14).
Water tank
A warning LED will light up at the end of the programme or when the tank is full with water.
The machine stops operating when this warning LED lights up. To restart the machine, please
drain the water in the water tank. Press Start/Pause/Cancel button to start the programme
after you have emptied the water tank. The warning LED goes off and the programme resumes
operating.
Starting the programme
Press the Start/Pause/Cancel button to start the programme. The Start/Pause/Cancel button
will light up to indicate that the programme has started.
Progress of programme
Progress of a running programme is shown through the programme follow-up indicator.
At the beginning of every programme step, the relevant indicator LED will light up and light of
the completed step will turn off.
Drying
Drying level will be illuminated during the whole drying process until the drying degree reaches
Ready to Iron.
Ready to Iron
Starts to illuminate when the drying degree reaches the Ready to Iron step and remains
illuminated until the next step.
Ready to Wear
Starts to illuminate when the drying degree reaches the Ready to Wear step and remains
illuminated until the next step.
End/Wrinkle Guard
Illuminates when the programme comes to an end and the anti-creasing function is activated.
ƒƒ If more than one LED lights up or flashes concurrently, it means there is a malfunction or a
failure. Please refer to the ‘Troubleshooting’ section (page 14).
10
Selecting a programme and operating your machine
Changing the programme after the programme has started
You can use this feature after your machine has started to dry your clothes under higher or
lower temperatures.
For example:
ƒƒ Press and hold the Start/Pause/Cancel button for about 3 seconds to cancel the programme in
order to select Extra Dry programme instead of ready to iron programme.
ƒƒ Select the Extra Dry programme by rotating the programme knob.
ƒƒ Press Start/Pause/Cancel button to start the programme.
The programme which is selected first will go on even if the programme selection button is
moved and another programme mode is selected while the machine is operating. You must
cancel the ongoing programme in order to change the drying programme. (See, ‘Ending the
programme through cancelling’ page 11).
Adding/removing laundry in standby mode
If you want to add or remove laundry into/from your machine after the drying programme has
started, put the machine into pause mode by pressing the Start/Pause/Cancel button. The
drying process will stop. Open the door at pause position and close it again after adding or
taking out laundry. Press Start/Pause/Cancel button to start the programme.
ƒƒ Any laundry added after the drying process was started may cause the already dried clothes in
the machine to intermingle with wet clothes and the result will be wet laundry after the drying
process is over.
ƒƒ It is not recommended to add laundry after the programme is started as it will increase the
programme time and energy consumption.
Childproof lock
There is a childproof lock to prevent any programme interruption due to the pressing of keys
while the programme is on. The loading door and all keys except the On/Off key on the panel are
deactivated when the childproof lock is active.
In order to activate the childproof lock, press on the Start/Pause/Cancel and Buzzer cancel
buttons simultaneously for 3 seconds.
To start a new programme after the programme is over or to interrupt the
programme, the childproof lock should be deactivated.
To deactivate the childproof lock, press the same buttons for 3 seconds.
Fig.6 Using the
childproof lock
Two beeps will sound when the childproof lock is activated. A single beep
will sound when the lock is deactivated.
Selecting a programme and operating your machine
11
Ending the programme through cancelling
The programme which is selected first will keep on going even if the position of the programme
selection button is changed. A new programme can be selected or the original drying
programme changed after a programme has been cancelled. In order to cancel the selected
programme press the Start/Pause/Cancel button for about 3 seconds. The clean filter, tank
full and End/ Wrinkle Guard warning LEDs will light up at the end of this period for reminding
purposes.
As the inside of the machine may be excessively hot when you cancel the programme while the
machine is running, activate the Freshen up programme to cool it down.
If the machine is stopped during any drying programme, and if the position of the programme
selection knob is changed, an audio signal will be heard (if the Buzzer Cancel function is not
selected). The machine will not start even if the Start/ Pause/Cancel button is pressed, unless
the programme selection knob is returned to the initial programme. The paused programme
must be cancelled in order to change the drying programme.
End of programme
The End/Wrinkle Guard, clean filter and tank full warning LEDs on the programme follow up
indicator will light up when the programme comes to an end. The door can be opened and the
machine becomes ready for a second cycle. Press the On/Off button to shut down the machine.
Important!
Clean the filter and drain the water tank after each drying process.
12
Maintenance and cleaning
Lint filter
Lint is generally formed during wearing and washing. Lint and fibres released from the laundry
to the air during the drying cycle are collected in the lint filter.
ƒƒ Always clean the filter after each drying process.
For filter cleaning;
Fig.7 Cleaning the lint filter
1
2
3
4
5
Open the door.
Remove the lint filter by pulling it up.
Open the filter.
Clean lint, fibres, etc from the filter by hand or with a soft piece of cloth.
Close the filter and place it back into its seat.
Important!
Do not operate the dryer without the lint filter in place.
Sensor
There are humidity sensors in your machine that detect whether the laundry is dry or not.
For sensor cleaning;
Fig.8 Cleaning the sensors
1 Open the door of your machine.
2 Allow the machine to cool off if drying has been carried out.
3 Wipe the metal sensors with a soft cloth, dampened with vinegar and dry them.
ƒƒ Clean metal sensors 4 times a year.
Maintenance and cleaning
13
Water tank
The moisture in the damp laundry is taken from the clothing and condensed. Drain the water
tank after each drying cycle or during drying when the tank full warning LED comes on.
Important!
ƒƒ Condensed water is not drinkable!
ƒƒ Never remove the water tank when the programme is running!
The water tank is located inside the drawer on the panel. If you forget to drain the water tank,
your machine will stop during the cycle when the water tank is full and the tank full warning
LED will light up. If this is the case, press the Start/Pause/Cancel button to resume the drying
cycle after draining the water tank.
To drain the water tank, carefully remove the water tank by pulling the drawer.
Fig.9 Emptying the water tank
1 Drain the water by opening the water tank cover.
2 If there is lint accumulation in the water tank cover, clean it and press to close.
3 Place the water tank back into its seat.
Condenser
Hot and humid air in the condenser is cooled with the cold air from the room. Thus, the
humid air circulating in your machine is condensed and then pumped into the tank.
ƒƒ Clean the condenser after every 20 drying cycles or once a month.
To clean the condenser
If a drying process has been carried out, open the door of the machine and wait until it cools down.
Open the kick plate, unlock the four condenser locks, and pull out the condenser.
Clean the condenser with pressurised water and wait until the water drains.
Replace the condenser with the side labelled “Top” facing upwards.
Lock the four condenser locks. Make sure that the red lock on the upper right corner is
engaged securely.
5 Close the kick plate cover.
ƒƒ
1
2
3
4
Fig.10 Cleaning the condenser
14
Troubleshooting
Problem
Cause
Explanation / Suggestion
Drying process
takes too long.
The filter cover and filter drawer
may need cleaning.
Check the filter cover and filter drawer
are free of lint. Clean if required.
Laundry is still wet
at the end of the
drying cycle.
The filter cover and filter drawer
may need cleaning.
Check the filter cover and filter drawer
are free of lint. Clean if required.
The machine may be overloaded.
Check that the load size does not
exceed the maximum capacity for the
product.
Machine does not
switch on, or the
programme does
not start.
The product may not have been
plugged in.
Make sure the power cord is plugged
in and machine is switched on.
The loading door may be ajar.
Ensure that the loading door is
properly closed.
Programme may not have been set, Check the programme has been
or the Start/Pause/Cancel button
selected and that it is not in
may not have been pressed.
Pause mode.
Childproof lock may have been
activated.
Deactivate the childproof lock.
Programme has
been interrupted
without any cause.
The loading door may be ajar
Ensure the loading door is properly
closed.
The power supply may have been
cut off to the machine.
Check the power cord is plugged in.
Press Start/Pause/Cancel button to
start the programme.
Laundry has
shrunk, become
felted, or
deteriorated.
A programme not suitable for
the type of laundry may have
been used.
Dry only the laundry which is suitable
for drying in your machine after
checking the care label on your
clothes.
Select a programme with a suitable
low temperature for the laundry type.
Drum lighting does
not come on.
The machine may not have been
Ensure that the machine is on.
turned on using the On/Off button.
The bulb may have blown.
tank full
warning
LED is on.
Wrinkle Guard
programme may be Drain the water in the water tank.
running.
Water Tank may be full.
Clean filter
is on.
LED
Call your nearest Fisher & Paykel
Authorised Repairer to replace
the bulb.
The filter may need cleaning.
Press Start/Pause/Cancel to resume
programme.
Check the filter cover is free of lint.
Clean if required.
Troubleshooting
15
Problem
Cause
Explanation / Suggestion
Drying process
takes too long.
The filter cover and filter drawer
may need cleaning.
Check the filter cover and filter drawer
are free of lint. Clean if required.
Laundy is still wet
at the end of the
drying cycle.
The filter cover and filter drawer
may need cleaning.
Check the filter cover and filter drawer
are free of lint. Clean if required.
The machine may be overloaded.
Check that the load does not exceed
the maximum capacity for the
product.
Machine does not
switch on, or the
programme does
not start.
The product may not have been
plugged in, or turned on.
Make sure the power cord is plugged
in, and machine is turned on.
The loading door may be ajar.
Ensure that the loading door is
properly closed.
Programme may not have been set, Check the programme has been
or the Start/Pause/Cancel button
selected and that it is not in Pause
may not have been pressed.
mode.
Childproof lock may have been
activated.
Deactivate the childproof lock.
Programme has
been interrupted
without any cause.
The loading door may be ajar.
Ensure the loading door is properly
closed.
The power supply may have been
cut off to the machine.
Check the power cord is plugged in.
Press Start/Pause/Cancel button to
start the programme.
Laundry has
shrunk, become
felted, or
deteriorated.
A programme not suitable for the
type of laundry may have been
used.
Dry only the laundry which is suitable
for drying in your machine after
checking the care label on your
clothes.
Select a programme with a suitable
low temperature for the laundry type.
Filter clean
LED
is on.
End/Wrinkle Guard
LED flashes.
End/Wrinkle Guard
Filter drawer/condenser may need
cleaning.
Open the kick plate and check the
filters in the condenser/filter drawer
are free of lint. Clean if required.
The 2-hour Wrinkle Guard
programme to prevent laundry
from creasing might have been
activated.
Turn off the machine and remove the
load.
Programme has come to an end.
Turn off the machine and remove the
load.
A heat sensor failure has occurred.
Machine ends the programme
without heating.
Turn off the machine and remove
the load. Call your Fisher & Paykel
Authorised Repairer.
LED is on.
The Drying LED
flashes.
Call a Fisher & Paykel Authorised Repairer if the problem persists.
16
Manufacturer’s Warranty
You automatically receive a 2 year Manufacturer’s Warranty with the purchase of this
Product covering parts and labour for servicing within the country of purchase.
Fisher & Paykel undertakes to:
Repair or, at its option, replace without cost to the owner either for material or labour any
part of the Product, the serial number of which appears on the Product, which is found to
be defective within TWO YEARS of the date of purchase.
Note: this Warranty is an extra benefit and does not affect your legal rights.
This Warranty DOES NOT cover
A Service calls which are not related to any defect in the Product. The cost of a service call will be
charged if the problem is found not to be a Product fault. For example:
1.
Correcting the installation of the Product.
2.
Instructing you how to use the Product.
3.
Replacing house fuses or correcting house wiring or plumbing.
4.
Correcting fault(s) caused by the user.
5.
Noise or vibration that is considered normal, eg drain/fan sounds, refrigeration noises
or user warning beeps.
6.
Correcting damage caused by pests, eg rats, cockroaches, etc.
7.
Poor drying performance due to incorrect installation eg no venting system fitted, dryer
vent against a wall, blocked lint filter.
8.
Poor drying performance due to incorrect loading, eg overloading or underloading.
9.
Damage from articles in the drum, eg bra wires, pens, crayons, dye transfer or flammable material.
10.
Dryer not heating due to timer dial being turned anticlockwise.
B Defects caused by factors other than:
1.
Normal domestic use or
2.
Use in accordance with the Product’s User Guide.
C Defects to the Product caused by accident, neglect, misuse or Act of God.
D The cost of repairs carried out by non-authorised repairers or the cost of correcting such
unauthorised repairs.
E Normal recommended maintenance as set out in the Product’s User Guide.
F Repairs when the appliance has been dismantled, repaired or serviced by other than a
Fisher & Paykel Authorised Repairer or the selling dealer.
G Pick-up and delivery.
H Transportation or travel costs involved in the repair when the Product is installed outside the
Fisher & Paykel Authorised Repairer’s normal service area.
This Product has been designed for use in a normal domestic (residential) environment. This
Product is not designed for commercial use (whatsoever). Any commercial use by a Customer will
affect this Product’s Warranty.
Service under this Manufacturer’s Warranty must be provided by a Fisher & Paykel Authorised
Repairer (refer to the ‘Customer Care’ section at the back of this book). Such service shall be provided
during normal business hours. This Warranty certificate should be shown when making any claim.
For Australian Customers
This Warranty is an extra benefit and does not affect your legal rights. Our goods come with
guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to
a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure.
Please keep this User Guide in a safe place.
Customer Care
17
Before you call for service or assistance…
Check the things you can do yourself.
Refer to your User Guide and check:
 Your appliance is correctly installed.
2 You are familiar with its normal operation.
3 You have read the Troubleshooting section.
If after checking these points you still need assistance, please refer to your nearest Fisher & Paykel
Authorised Repairer, or contact us through our local website listed on the back cover.
In Australia if you need assistance...*
Call the Fisher & Paykel Customer Care Centre and talk to one of our Customer Care Consultants.
Toll Free: 1 300 650 590 Fax: (07) 3826 9298
Email: customer.care@fp.com.au Postal Address: PO Box 798, Cleveland QLD 4163
If you need service...*
Fisher & Paykel has a network of qualified Fisher & Paykel Authorised Repairers responsible for
servicing only Fisher & Paykel branded appliances. Our Customer Care Centre can recommend a
qualified Fisher & Paykel Authorised Repairer in your area.
*If you call, write or contact our website please provide: your name and address, model number,
serial number, date of purchase and a complete description of the problem. This information is
needed in order to better respond to your request for assistance.
Product details can be found on a sticker situated on the back of the dryer cabinet,
or on the inside of the dryer door.
Product details
Fisher & Paykel Appliances, Ltd
Model/Serial No.
Date of Purchase Purchaser
Dealer Suburb
Town Country
www.fisherpaykel.com.au
Copyright © Fisher & Paykel 2011. All rights reserved.
The product specifications in this booklet apply to the specific products
and models described at the date of issue. Under our policy of continuous
product improvement, these specifications may change at any time. You
should therefore check with your Dealer to ensure this booklet correctly
describes the product currently available.
AU
F&P PN - 790817 D
07.2011
Download PDF

advertising