Datavideo ITC-100 KF1000 Network Card User Manual

ITC-100 KF1000
8 Channel Intercom / Talkback
System for SE-1000
Instruction Manual
http:// www.datavideo-tek.com
Rev: 280807
Warnings and Precautions
1. Read all of these warnings and save them for later reference.
2. Follow all warnings and instructions marked on this unit.
3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a
damp cloth for cleaning.
4. Do not use this unit in or near water.
5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious
damage.
6. Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To ensure
safe and reliable operation of this unit, and to protect it from overheating, do not block or cover
these openings. Do not place this unit on a bed, sofa, rug, or similar surface, as the ventilation
openings on the bottom of the cabinet will be blocked. This unit should never be placed near or
over a heat register or radiator. This unit should not be placed in a built-in installation unless
proper ventilation is provided.
7. This product should only be operated from the type of power source indicated on the marking label
of the AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer
or your local power company.
8. Do not allow anything to rest on the power cord. Do not locate this unit where the power cord will
be walked on, rolled over, or otherwise stressed.
9. If an extension cord must be used with this unit, make sure that the total of the ampere ratings on
the products plugged into the extension cord do not exceed the extension cord’s rating.
10. Make sure that the total amperes of all the units that are plugged into a single wall outlet do not
exceed 15 amperes.
11. Never push objects of any kind into this unit through the cabinet ventilation slots, as they may
touch dangerous voltage points or short out parts that could result in risk of fire or electric shock.
Never spill liquid of any kind onto or into this unit.
12. Except as specifically explained elsewhere in this manual, do not attempt to service this product
yourself. Opening or removing covers that are marked “Do Not Remove” may expose you to
dangerous voltage points or other risks, and will void your warranty. Refer all service issues to
qualified service personnel.
13. Unplug this product from the wall outlet and refer to qualified service personnel under the following
conditions:
a. When the power cord is damaged or frayed;
b. When liquid has spilled into the unit;
c.
When the product has been exposed to rain or water;
d. When the product does not operate normally under normal operating conditions. Adjust
only those controls that are covered by the operating instructions in this manual; improper
adjustment of other controls may result in damage to the unit and may often require
extensive work by a qualified technician to restore the unit to normal operation;
e. When the product has been dropped or the cabinet has been damaged;
f.
When the product exhibits a distinct change in performance, indicating a need for service.
Warranty
1
Datavideo warrants that the equipment it manufactures shall be free from defects in material and
workmanship for a period of 12 months from the date of product purchased. If equipment fails due to
such defects, Datavideo will, at its option, repair or provide a replacement for the defective part or
product.
Equipment that fails after the warranty period, has been operated or installed in a manner other than
that specified by Datavideo, or has been subjected to abuse or modification, will be repaired for time
and material charges at the Buyer’s expense. This warranty does not affect your statutory rights
within the Country of purchase.
For EU Customers only - WEEE Marking.
This symbol on the product indicates that it will not be treated as household waste. It must be handed
over to the applicable take-back scheme for the recycling of electrical and electronic equipment. For
more detailed information about the recycling of this product, please contact your local Datavideo
office.
Introduction
The ITC-100 is a 19” Rack Mount 8 Way Intercom / Talkback System. It incorporates
tally indicators for each channel and individual channel call buttons as well as a call
all channels button.
It is ideal in a live environment and enables easy bi-directional communication
between all members of the crew. It is a perfect accessory for the Datavideo
SE-1000 vision mixers.
2
Contents
WARNINGS AND PRECAUTIONS
1
WARRANTY
2
INTRODUCTION
2
PACKING LIST
3
FRONT PANEL CONNECTIONS
4
REAR PANEL CONNECTIONS
6
ITC-100SL SLAVE UNIT
7
USING THE ITC-100 WITH THE SE-1000 / TB-10
9
ITC-100 TALLY INPUT PIN CROSS REFERENCE
10
SPECIFICATIONS
11
SERVICE AND SUPPORT
13
Packing List
1. ITC-100 KF 1000
Main Unit
x
1
2. ITC-100SL Slave Unit
x
6
3. ITC-100SL Carrying Case
x
6
4. 20m XLR to XLR Intercom Cable
x
6
5. MC-1 Headset / Microphone
x
6
6. MC-2 XLR Gooseneck Mic
x
1
7. LP-1 XLR Gooseneck Light
x
1
8. 12V 3.0A Power Supply Unit
x
1
9. AC Power cord.
x
1
10. Instruction Manual
x
1
3
Front Panel:
On / Off Switch
Powers the ITC-100 On / Off. Red LED indicates that unit is switched on.
XLR Microphone Socket
Combined XLR / ¼” (6.3mm) Jack Microphone Input for either a
Condenser or Dynamic Gooseneck Microphone. XLR supports
Condenser Microphones ¼” (6.3mm) Jack supports Dynamic.
Headphone Socket
¼ “ / 6.3mm Stereo Headphone Socket for conventional headphones.
Plugging in headphones will disable the built-in speaker
Microphone / Headset Socket
3.5mm Stereo Socket for combined Microphone Headset.
Plugging in a Microphone / Headset will disable the built-in speaker and
the XLR Microphone Input.
ALL Button
Opens communication with all channels. All channels will hear
communication from the operator, or from any other channel using the
TALK button.
4
Channel Buttons 1~6 + AUX 1 / 2
Opens communication with individual channels. More than 1 channel
can be active at any given time, active channels are illuminated red.
All active channels will hear any communication from the operator or
from any other active channel.
The buttons will also indicate if any channel is paging, the paging
channel will flash in orange until the page is answered.
MUTE Button
Mutes all communication from the base station or any channel.
N.B. If any channel uses the CALL button the paging tone will still
sound even when the MUTE button is active.
Volume Control
Controls the Volume of the built-in speaker or outputs to the
headphones or mic/headset according to what is connected
Built-In Speaker
Sounds audible alert when a channel is paging and provides audio
during talkback conversations. Speaker is mute when headphones or
mic / headset are connected to the ITC-100
12V Light Socket
12V Powered light socket for gooseneck light (supplied).
5
Rear Panel:
Channel Input / Output XLR Sockets
Each of the 8 channels has an XLR connector that carries
bi-directional signals between the ITC-100 and ITC-100SL. All
connections are contained within the one cable. Channels 1 ~ 3
are supplied tally light information from tally A; channels 4 ~ 6
are supplied tally light information from tally B.
Tally Inputs A & B
Tally Inputs A & B are configured for direct connection to the
Datavideo SE-1000 via the TB-10. They supply tally information
to the ITC-100SL; RED indicates Live. Tally A will feed
information to channels 1 ~ 3 and Tally B will feed information to
channels 4 ~ 6
DC In 12V 2.5A
Connect the 12V 3.0A power supply. The power supply plug
has a screw in locking collar to secure the connection.
Ground Terminal
When connecting this unit to any other component, make sure
that it is properly grounded by connecting this terminal to an
appropriate point. When connecting, use the socket and be sure
to use wire with a cross-sectional area of at least 1.0 mm2.
6
ITC-100SL Slave Unit :
XLR Connection
Connects the ITC-100SL to the ITC-100 Base Station. Power, tally and
bi-directional audio are all carried through the same cable.
Call Button
Sends a paging message to the ITC-100 Base Station. The channel button
will flash orange and there will be an audible tone, each time the button is
pressed.
Tally LED
Will illuminate RED when the channel is LIVE
Talk Button
Opens up talk back communication with the ITC-100 base station, and any
other active channels. Press the button to activate, press a second time to
de-activate. PLEASE NOTE: It is important to press the button to
deactivate the talk channel as soon as you have finished talking,
otherwise it will remain an open channel and become distracting and
confusing for other members of the crew.
Volume Control
Adjusts the volume of the headphones.
7
Mic / Headphone Socket
The ITC-100SL has both a 3.5mm and 2.5mm Mic / Headset socket. A
standard 3.5mm Mic / Headset can be used, or a Motorola type 2.5mm Mic /
headset could be used if preferred.
External Tally LED Socket
An external tally display (TD-1) can be connected to the ITC-100SL. This
enables the tally light to be positioned in a more convenient place, such as on
top of the camera. When the channel is LIVE the LED will be RED, and when
the channel is CUED the LED will be AMBER.
N.B. The Tally LED on the ITC-100SL will continue to operate as normal
when a TD-1 has been added.
Power LED
The Power LED indicates when the channel is active. If the operator has
opened the channel by pressing the channel button 1 ~ 8, or by pressing ALL
then the LED will light up.
N.B. The tally indicator lights will continue to work even when the
Power LED is not on, and the channel is not active.
8
Using the ITC-100 KF1000 with the SE-1000 / TB10:
The ITC-100 KF1000 is an ideal accessory for the Datavideo SE-1000 Vision Mixer.
The SE-1000 has five HD / SDI channels, so in the diagram below we have five
camera crew, each with an ITC-100SL. The sixth ITC-100SL could be for
communicating with the graphics operator or other members of the crew.
The Tally output from the SE-1000 connects to the TB-10; this provides the status
of the SE-1000. The TB-10 Tally Out connects to the ITC-100 Tally Inputs A and B.
Tally Input A provides tally information to channels 1 ~ 3, Tally Input B provides tally
information to channels 4 ~6 , when the camera is live the cameraman will see a
red light.
9
ITC-100 Tally Input - Pin Cross Reference
If you are using the ITC-100KF1000 with a Datavideo SE-1000 via a TB-10 you do
not need to worry about tally information, as it is automatically sent to the ITC-100
KF1000. If you are using the ITC-100 with other equipment the following tables
explain the pin configurations of Tally A and Tally B.
Contact closure between the relevant Pin number and ground will illuminate the LED.
For example on Tally A, if Pin 1 is connected to Pin 4 the RED LED will light up on
Channel 1; if Pin 13 is connected to Pin 4 the AMBER LED will light up on Channel 3
Tally A Input
The Tally A Input will send Tally Information to Channels 1 ~ 4. The following table
shows the pin numbers for each channel:
Video
Channel
Red LED
LIVE
(On Air)
Amber LED
CUED
(Next)
1
Pin 1
Pin 3
2
Pin 6
Pin 8
3
Pin 11
Pin 13
AUX 1
Pin 5
Pins 4, 9 and 14 can be used as ground.
Pin 15
Tally B Input
The Tally B Input will send Tally Information to Channels 5 ~ 8. The following table
shows the pin numbers for each channel:
Video
Channel
Red LED
LIVE
(On Air)
Amber LED
CUED
(Next)
4
Pin 1
Pin 3
5
Pin 6
Pin 8
6
Pin 11
Pin 13
AUX 2
Pin 5
Pins 4, 9 and 14 can be used as ground.
10
Pin 15
Specification:
ITC-100 Base Station
Specification
POWER
12V 2.5A
TALLY
2 x 15 Pin SubD Sockets for Tally A and Tally B
MIC / HEADSET
3.5mm Stereo Jack Socket for combination
Headphone / Microphone
Headset Impedance 8~600 ohms 100mW(min)
INPUTS /
HEADPHONE
OUTPUTS
¼” (6.3mm) Stereo Headphone Socket
Headset Impedance 8~600 ohms 100mW(min)
LIGHT SOCKET
3 pin XLR connector. Pin2: 12V, Pin3: GND.
(12V DC)
Light power consumption 12V/100mA(max).
MICROPHONE
3 Pin XLR / ¼” (6.3mm) Jack Microphone
Socket Switchable Condenser / Dynamic Input
Microphone Level -67dB
FREQUENCY RESPONSE
550-3.6KHz, < +/-3dB
THD
< 3%
S/N
> 50dB
BUILT-IN SPEAKER
70mm x 30mm 32 Ohm 3 Watts
OPERATING RANGE
Up to 200m between Base Station and Slave
OPERATING TEMP. RANGE
5 ~ 45°C
DIMENSION
750mm x 650mm x 250mm (1U height 19” rack)
WEIGHT
1.9Kg
11
ITC-100SL SLAVE Unit
Specification
INPUT
5 Pin XLR Connector
MIC / HEADSET SOCKET
3.5mm Stereo Jack Socket for combination
Headphone / Microphone
Headset Impedance 8~600 ohms 100mW(min)
Microphone Level -67dB
Or
2.5mm Stereo Jack Socket, for Motorola Mobile
Phone type headset / microphone
TALLY OUT SOCKET
3.5mm Jack Socket to connect to TD-1 Tally
Indicator
TALLY LED
Bi-Color LED – RED indicates LIVE / AMBER
Indicates CUED (single color with SE-1000)
POWER LED
Illuminates to indicate that power is being
received
OPERATING RANGE
Up to 200m between Base Station and Slave
OPERATING TEMP. RANGE
5 ~ 45°C
DIMENSION
114mm x 97mm x 35mm
WEIGHT
348g
12
Service and Support
It is our goal to make your products ownership a satisfying experience. Our
supporting staff is available to assist you in setting up and operating your system.
Please refer to our web site www.datavideo-tek.com for answers to common
questions, support requests or contact your local office below.
Datavideo Corporation (USA)
12300-U East Washington Blvd., Whittier, CA 90606 USA
Tel: +1 562 696 2324
contactus@datavideo.us
www.datavideo.us
Datavideo Technologies Europe BV
Floridadreef 106, 3565 AM Utrecht, The Netherlands
Tel: +31 30 261 9656
info@datavideo.nl
www.datavideo.info
Datavideo UK Limited
Unit 2 Waterside Business Park, Hadfield, Glossop, Derbyshire SK13 1BE UK
Tel: +44 1457 851000
sales@datavideo.co.uk
www.datavideo.info
Datavideo Technologies Co., Ltd.
10F, 176 Jian-Yi Rd, Chung Ho City, Taipei Hsien, Taiwan 235
Tel: +886 2 8227 2888
service@datavideo.com.tw www.datavideo.com.tw
Datavideo Technologies China Co.
2F-D, 2 Lane 777, West Guangzhong Rd, Zhabei District, Shanghai, China
Tel: +86 21 5603 6599
service@datavideo.cn
www.datavideo.cn
Datavideo Technologies (S) PTE Ltd.
No. 100, Lorong 23 Geylang, #01-03 D’Centennial Bldg, Singapore 388398
Tel: +65 6749 6866
info@datavideo.sg
www.datavideo.info
Datavideo Hong Kong Limited
G/F., 26 Cross Lane, Wanchai, HK
Tel: +852 2833 1981
info@datavideohk.com
13
www.datavideohk.com