Quick
Installation Guide
300Mbps Wireless N USB VDSL/ADSL Modem Router
TD-W9970/TD-W9970B
*TD-W9970 is used for demonstration in this QIG.
7106506058 REV2.0.0
1. Connecting the Hardware
1
Connect the splitter and power adapter as follows. Press the ON/OFF button and the
Power LED turns on.
Phone Jack
Splitter
VDSL LAN4/WAN LAN3 LAN2 LAN1 USB WiFi
WPS/
RESET
ON/OFF POWER
Note: If you don’t need the phone service, just directly connect the VDSL port to the Phone Jack with a phone cable.
2
Check the Power and DSL LED lights to ensure the hardware connection is correct.
Notes:
Please wait 1-2 minutes until the DSL LED is on.
If the Wireless LED is off, please press the WiFi button on the rear panel for
2 seconds, then check the LEDs again in a few seconds.
Power
On
DSL
On
Wireless
On
2. Configuring the Modem Router
1
Connect your computer to the modem router (Wired or Wireless).
Wired
VDSL LAN4/WAN LAN3 LAN2 LAN1 USB WiFi
WPS/
RESET
ON/OFF POWER
Ethernet cable
Wireless
Or
Connect wirelessly by using the default network name (SSID) and password on the product label printed on the bottom of the modem router.
2
Open a web browser on the computer and configure the modem router according to the following main clues.
a
Enter http://tplinkmodem.net or http://192.168.1.1 in the address bar. Type in admin for both the username and password and click Login.
Note: If the login window does not appear, please refer to
FAQ->Q1.
b
Click Next to start Quick Setup, and select your Region and Time Zone from the drop-down list. Then click Next. admin admin http://tplinkmodem.net
Login
Quick Setup-Region and Time Zone
Region
Time Zone
--please select--
--please select--
Back Next c
Select Yes to auto detect your connection type and then click
Next to continue.
Quick Setup-Auto Detection
Auto-Detect Connection Type:
Yes.
No. I want to configure The Internet Connection myself.
Back Next d
Enter the parameters provided by your ISP and then click Next. Here we take PPPoE as an example.
Quick Setup-PPPoE
Auto-detection has succeeded!
DSL PVC: 8/35
Encapsulation Mode: LLC
Connection Type: PPPoE
User name:
Password:
Confirm Password:
XXXXXX
XXXXXX
XXXXXX
Back Next g
Click Save and wait for your settings to take effect. Click Finish to complete the setup.
Quick Setup-Complete
Time Zone Configuring: Success
Operation Mode Configuring: Success
WAN Connection Configuring: Success
3G/4G Connection Configuring: Success
Gateway and DNS Configuring: Success
Wireless Configuring: Success
Finish e
Click Next to continue.
Note: You may enable 3G/4G as a backup method for Internet access.
Quick Setup-3G/4G
Enable 3G/4G as a backup solution for Internet access.
Enjoy!
Now your wired and wireless devices can connect to the Internet !
Note: If you have changed your wireless network name and password, you must sign in with the new names/passwords to regain access to the Internet.
Back Next f
Click Next to continue.
Note: You may rename your wireless network name and create your own password.
Quick Setup-Wireless
Wireless Network Name:
Channel:
Mode:
Security:
Password:
TP-LINK_XXXX
XXXXXXXX
Back Next
Select Yes to auto detect your connection type and then click
Next to continue.
USB Features
The USB port can be used for media sharing, storage sharing and printer sharing across your local network. You can also set up the FTP server to access your files remotely by connecting to the Internet.
Note: To learn more about the USB features, please visit http://tp-link.com/app/usb, or simply scan the QR code.
VDSL LAN4/WAN LAN3 LAN2 LAN1 USB WiFi
WPS/
RESET
ON/OFF
USB sharing port
POWER
Remote
Access via
FTP Server
Media
Sharing
Local
Storage
Sharing
Printer
Sharing
Frequently Asked Questions (FAQ)
Q1. What can I do if the login window does not appear?
A1. If the computer is set to a static or fixed IP address, change it to obtain an IP address automatically.
A2. Verify http://tplinkmodem.net or http://192.168.1.1 is correctly entered in the web browser and press Enter.
A3. Use another web browser and try again.
A4. Reboot your modem router and try again.
A5. Disable the network adapter used currently then enable it again.
Q2. What can I do if I cannot access the Internet?
A1. Check your cables and make sure they are all plugged in correctly, including the telephone line, Ethernet cable and power adapter.
A2. Check to see if you can log on to the Web-Management page of the modem router.
The default address of the Web-Management page is http://tplinkmodem.net or http://192.168.1.1. If you can, try the following steps. (If you can not, please set your computer to obtain an IP address automatically and then try to access the
Internet again.)
A3. Consult your ISP and make sure all the VPI/VCI, Connection Type, account username and password are correct. If they are not, please replace them with the correct settings and try again.
A4. If you still cannot access the Internet, please restore your modem router to its factory default settings and reconfigure your modem router following the instructions in this QIG.
A5. Please contact our Technical Support if the problem still exists.
LED Indicators
Name
(Power)
(DSL)
(Internet)
(Wireless)
(WPS)
(USB)
(LAN 1-4)
Status
On
Flash
Off
On
Flash
Off
On
Off
On
Off
On/Off
Flash
On
Flash
Off
On
Off
Q3. How do I restore the modem router to its factory default settings?
A1. With the modem router powered on, press and hold down the WPS/RESET
Button on the rear panel of the modem router for approximately 5 seconds.
A2. Log in Web Management page of the modem router, and go to System
Tools->Factory Defaults, click Restore, then wait until the progress bar loading finished.
VDSL LAN4/WAN LAN3 LAN2 LAN1 USB WiFi
WPS/
RESET
ON/OFF POWER
WPS/RESET Button
Press & Hold for 5 seconds
Q4. What can I do if I forget my password?
Web Management page password:
Restore the modem router to its factory default settings and then use the default Username ‘admin’ and
Password ‘admin’ to log in.
Wireless Network password:
A1. The factory default password can be found on the product label printed on the bottom of the modem router.
A2. If you have changed your password, log on to the modem router’s Web Management page, go to
Wireless->Wireless Security to obtain or reset your password.
Indication
System start-up complete.
System starting up or device updating.
Power is off.
DSL line is synchronized and ready to use.
The DSL negotiation is in progress.
There is no connection to the DSL Port or DSL synchronization fails.
The network is available with a successful Internet connection.
There is no successful Internet connection or the modem router is operating in Bridge mode.
The wireless function is working properly.
The wireless function is disabled.
It turns on when a wireless device has been successfully connected to the network via WPS.
After about 5 minutes, the WPS LED will turn off.
WPS handshaking is in process and will continue for about 2 minutes.
The USB device is identified and ready to use.
The USB device is being identified.
No USB device is plugged in to the USB port.
There is a device connected to this LAN Port.
There is no device connected to this LAN Port.
VDSL LAN4/WAN LAN3 LAN2 LAN1 USB
©2016 TP-LINK
