Dell 1320 Laptop User Manual

Dell™ Vostro™ 1320 Service Manual Working on Your Computer
Adding and Replacing Parts
Specifications
Diagnostics
System Setup
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
If you purchased a Dell™ n Series computer, any references in this document to Microsoft® Windows® operating systems are not applicable.
Information in this document is subject to change without notice.
© 2009 Dell Inc. All rights reserved.
Reproduction of this material in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, Vostro, TravelLite, Wi-Fi Catcher, and ExpressCharge, are trademarks of Dell Inc.; Intel, Pentium, Celeron a n d Core are registered
trademarks of Intel Corporation; Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell under license; TouchStrip is a trademark of Zvetco Biometrics,
LLC; Blu-ray Disc is a trademark of the Blu-ray Disc Association; Microsoft, Windows, Windows Vista, and the Windows Vista start button are either trademarks or registered
trademarks of Microsoft Corporation in the United States and/or other countries.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
May 2009 Rev. A00
Back to Contents Page
System Setup
Dell™ Vostro™ 1320 Service Manual Entering System Setup
<F12> Menu
Your computer's BIOS, or System Setup program allows you to do the following:
l
l
Access System Setup by pressing <F2>
Bring up a one-time boot menu by pressing <F12>
Entering System Setup
Press <F2> to enter System Setup and make changes to the user-definable settings. If you are having trouble entering Setup using this key, reboot and press
the <F2> key when the keyboard LEDs first flash.
<F12> Menu
Press <F12> when the Dell logo appears to initiate a one-time boot menu with a list of the valid boot devices for the computer. The devices listed on the boot
menu depend on the bootable devices installed in your computer.
l
l
l
l
l
Internal HDD
CD/DVD/CD-RW Drive
Onboard NIC
BIOS Setup
Diagnostics (starts the Pre-boot System Assessment (PSA) diagnostics)
This menu is useful when attempting to boot to a particular device or to bring up the diagnostics for your computer. Using the boot menu does not make any
changes to the boot order stored in the BIOS.
Back to Contents Page
Diagnostics
Dell™ Vostro™ 1320 Service Manual
Device Status Lights
LED Error Codes
Power Button Light Codes
Device Status Lights
1—Turns on when your computer reads or writes data to the hard drive.
NOTE: To avoid loss of data, never turn off your computer while the Hard Drive light is flashing.
2—Turns on when wireless networking is enabled.
3—Turns on when a card with Bluetooth® wireless technology is enabled.
NOTE: The card with Bluetooth wireless technology is an optional feature, so the light turns on only if
you ordered the card with your computer. For more information, see the documentation that came
with your card.
To turn off only the Bluetooth wireless technology functionality, right-click the icon in the system tray
and click Disable Bluetooth Radio.
4—Turns on when the numeric keypad is enabled.
5—Turns on when the uppercase letter function is enabled.
6—Turns on when the scroll lock function is enabled.
Device status lights located in the center of the
hinge cover.
If your computer is connected to an electrical outlet, the
l
l
If your computer is running on a battery, the
l
l
l
light operates as follows:
Solid blue—The battery is charging.
Flashing blue—The battery is almost fully charged.
light operates as follows:
Off—The battery is adequately charged, or the computer is turned off.
Flashing orange—The battery charge is low.
Solid orange—The battery charge is critically low.
LED Error Codes
If your computer does not perform a Power-On Self-Test upon boot up, there are various things to look for:
1.
2.
3.
Check that the computer power light is on.
If the power light is not on, ensure that your computer is plugged into AC power. Remove the battery.
If your computer is powered on but is not performing a POST, check to see whether or not the keyboard status lights flash to indicate a successful POST
but no video or if the keyboard status lights are lit in a sequence indicating a system problem.
The following table shows the possible LED codes that may display in a no-POST situation.
Appearance
Description
ON-FLASH-FLASH
Next Step
1.
2.
4.
Install supported memory modules.
If memory is already present, reseat the module(s) one at
time in each slot.
Try known good memory from another computer or replace the
memory.
Replace the system board.
System board error
1.
2.
3.
Reseat the processor.
Replace the system board.
Replace the processor.
LCD Panel Error
1.
2.
3.
Reseat the LCD cable.
Replace the LCD panel.
Replace the video card / system board.
1.
Install compatible memory modules.
No SODIMMs are installed
3.
FLASH-ON-ON
FLASH-ON-FLASH
OFF-FLASH-OFF
2.
Memory compatibility error
3.
4.
ON-FLASH-ON
1.
2.
Memory is detected but has
errors
If two modules are installed remove one and test. Try the
other module in the same slot and test. Test the other slot
with both modules.
Replace the memory.
Replace the system board.
3.
4.
Reseat the memory.
If two modules are installed remove one and test. Try the
other module in the same slot and test. Test the other slot
with both modules.
Replace the memory
Replace the system board.
1.
2.
3.
Reseat the modem.
Replace the modem.
Replace the system board.
1.
Replace the system board.
1.
2.
3.
Reseat the device.
Replace the device.
Replace the system board.
1.
2.
3.
4.
Reseat the hard drive and optical drive.
Test the computer with just the hard drive and just the optical
drive.
Replace the device that is causing the failure.
Replace the system board.
1.
Replace the system board.
OFF-FLASH-FLASH
Modem Error
FLASH-FLASH-FLASH
System board error
FLASH-FLASH-OFF
Option ROM Error
OFF-ON-OFF
Storage device error
FLASH-FLASH-ON
Video card error
Power Button Light Codes
The power LED located in the power button on the front of the computer illuminates and blinks or remains solid to indicate five different states:
l
No light—System is in the off state (S5, or mechanical (AC power not applied) OFF).
l
l
l
l
Solid Amber—System fault, but power supply is good—normal operating state (S0).
Blinking Amber—System fault error condition including Power Supply (only +5VSB working), Vreg failure, missing or bad CPU.
Blinking Green—System is in power saving states S1, S3 or S4. (Blink rate is 1Hz). No fault/error condition.
Solid Green—System is fully functional and is in S0 (ON) state.
Back to Contents Page
Adding and Replacing Parts
Dell™ Vostro™ 1320 Service Manual Battery
Optical Drive
Hard Drive
Access Panel
Memory
Fan
Heat Sink and Processor
Wireless Local Area Network (WLAN) Card
Hinge Cover
Keyboard
Display Assembly
Display Bezel
Display Inverter
Camera
LCD Display Panel
Display Assembly Hinges
Palm Rest
Fingerprint Reader
Internal Card With Bluetooth® Wireless Technology
System Board
Coin-Cell Battery
Speaker Assembly
Back to Contents Page
Specifications
Dell™ Vostro™ 1320 Service Manual Processors
Display
System Information
Keyboard
ExpressCard™
Touch Pad
Memory Card Reader
Fingerprint Reader
Memory
Camera
Connectors
Battery
Communications
AC Adapter
Video
Physical
Audio
Environmental
NOTE: Offerings may vary by region. For more information regarding the configuration of
your computer, click Start
(or Start in Windows XP)® Help and Support, and then
select the option to view information about your computer.
Processor Processor type
Intel® Core™ 2 Duo processors
L1 cache
32 KB per instruction, 32 KB data cache per core
L2 cache
Shared 3 MB or 6 MB
External bus frequency
1067 MHz
System Information System chipset
Intel GM45 or Intel PM45 chipset
Data bus width
64 bits
DRAM bus width
64 bits
Processor address bus width
36 bits
Flash EPROM
SPI 32 Mbit
PCI bus (discrete graphics only)
x16 PCI Express
ExpressCard™
NOTE: The ExpressCard slot is designed only for ExpressCards. It does NOT support PC cards.
ExpressCard connector
ExpressCard slot (supports both USB- and PCIe-based
interfaces)
Cards supported
34-mm and 54-mm ExpressCards
Memory Card Reader
Cards supported
SD, SDIO, SD HC, Mini SD (with adapter) MMC, MMC+,
Mini MMC (with adapter)
Memory
Memory module connector
Two DIMM sockets
Memory module capacities
1 GB (one DIMM), 2 GB (one DIMM or two DIMMs), 3 GB (2
DIMMs), 4 GB (2 DIMMs)
Memory type
DDR2 800 MHz non-ECC memory only
Minimum memory
1024 MB (1 GB)
Maximum memory
4096 MB (4 GB)
Connectors Audio
Microphone connector, stereo headphone/speakers
connector
IEEE 1394
One 4-pin connector
Dock
Optional USB Port Replicator only
Mini-card support (internal expansion slots)
One dedicated half Mini-Card slot for WLAN
One dedicated full Mini-Card slot for WPAN (Bluetooth® or ultra wideband [UWB])
WPAN full Mini-Card slot can also be used for the Intel
Flash Cache
Modem
Optional USB external modem
Network adapter
RJ-45 connector
USB, USB PowerShare, eSATA
Four 4-pin USB 2.0-compliant connectors
Video
VGA
Communications
Modem
External (optional)
Network adapter
10/100/1000 Ethernet LAN on system board
Wireless
WLAN half Mini-Card, WPAN full Mini-Cards, Bluetooth
wireless support, and UWB technology
Mobile Broadband
None
GPS
None
Video Video type
Integrated
Discrete on system board, hardware accelerated
Video controller
Integrated video: Mobile Intel GMA X4500
Discrete video: NVIDIA GeForce 9300M GS
Data bus
Integrated video or PCI-Express video x16
Video memory
Integrated video: up to 256 MB shared
Discrete video: 256 MB dedicated memory
Video output
Video connector and multimode DisplayPort
Audio Audio type
Two-channel high definition audio codec
Audio controller
IDT 92HD71B5
Stereo conversion
24-Bit (stereo digital-to-analog)
24-Bit (stereo analog-to-digital)
Interfaces:
Internal
Internal High Definition Audio
External
Microphone-in connector, stereo headphones / speakers
mini-connector
Speaker
One 2-watt, 4-ohm speakers
Internal speaker amplifier
1-Watt channel into 4 ohms
Internal microphone
Single digital microphone
Volume controls
Volume control buttons
Display Type (active-matrix TFT)
13.3" WXGA anti-glare CCFL
13.3" WXGA TrueLife CCFL
Dimensions
Height
178.8 mm (7.03 inches)
Width
286.08 mm (11.26 inches)
Diagonal
337.82 mm (13.3 inches)
Maximum Resolutions
WXGA
1280 x 800 at 262 K colors
WXGA TrueLife
1440 x 900 at 262 K colors
Operating angle
0° (closed) to 130°
Refresh rate
60 Hz
Viewing angles
Horizontal
±40° (WXGA) typical
±40° (WXGA with TrueLife)
Pixel pitch
WXGA
0.2235 mm
Keyboard
Number of keys
84 (U.S. and Canada); 85 (Europe); 88 (Japan)
Layout
QWERTY/AZERTY/Kanji
Size
full sized (19 mm key pitch)
Touch Pad
X/Y position resolution
(graphics table mode)
240 CPI
Size
Width
73.0-mm (2.9 inch) sensor-active area
Height
42.9-mm (1.7 inch) rectangle
Fingerprint Reader (Optional)
Type
UPEK TCS3 TouchStrip™ strip sensor with CMOS active capacitive pixel-sensing technology
Camera (Optional)
Resolution
640 x 480 pixels (VGA)
Battery
Type
12-cell lithium-ion prismatic slice battery
84 WHr
9-cell lithium-ion battery
85 WHr
6-cell lithium-ion battery
56 WHr
4-cell lithium-ion battery
35 WHr
Dimensions: Depth 4- or 6-cell lithium-ion battery
206 mm (8.11 inches)
9-cell lithium-ion battery
93.3 mm (3.67 inches)
12-cell lithium-ion battery
14.48 mm (0.57 inches)
Height 4- or 6-cell lithium-ion battery
19.8 mm (0.78 inch)
9-cell lithium-ion battery
22.3 mm (0.88 inch)
12-cell lithium-ion battery
217.24 mm (8.55 inch)
Width 4- or 6-cell lithium-ion battery
47.0 mm (1.85 inches)
9-cell lithium-ion battery
68.98 mm (2.70 inches)
12-cell lithium-ion battery
322.17 mm (12.68 inches)
Weight 4-cell lithium-ion battery
0.24 kg (0.53 lb)
6-cell lithium-ion battery
0.33 kg (0.73 lb)
9-cell lithium-ion battery
0.51 kg (1.12 lb)
12-cell lithium-ion battery
0.85 kg (1.87 lb)
Voltage
4-cell lithium-ion battery
14.8 VDC
6- or 9-cell lithium-ion battery
11.1 VDC
12-cell lithium-ion battery
14.8 VDC
Charge time (approximate)
Computer off
6-cell lithium-ion battery
Approximately 1 hour to 80% capacity
Approximately 2 hours to 100% capacity
Operating Time
Varies depending on operating conditions and can be
significantly reduced under certain power-intensive
conditions
Life span (approximate)
1 year
Temperature range
Operating
0°C to 40°C (32°F to 104°F)
Storage
–10° to 65°C (14° to 149°F)
Coin-cell battery
CR-2032
AC Adapter
Input voltage
100-240 VAC
Input current (maximum)
1.5 A
Input frequency
50–60 Hz
Temperature range:
Operating
0°C to 35°C (32° to 95°F)
Storage
–40°C to 65°C ( –40° to 149°F)
PA-12 65-W Travel AC adapter:
Output voltage
19.5 V DC
Output current
3.34 A
Height
15 mm (0.6 inches)
Width
66 mm (2.6 inches)
Depth
127 mm (5.0 inches)
Weight
0.29 kg (0.64 lb)
PA-10 90-W D-Series AC adapter:
Output voltage
19.5 V DC
Output current
4.62 A
Height
32 mm (1.3 inches)
Width
60 mm (2.4 inches)
Depth
140 mm (5.5 inches)
Weight
0.425 kg (0.9 lb)
PA-3E 90 E-Series AC adapter:
Output voltage
19.5 V DC
Output current
4.62 A
Height
15 mm (0.6 inches)
Width
70 mm (2.8 inches)
Depth
147 mm (5.8 inches)
Weight
0.345 kg (0.76 lb)
Physical
Height
27–31 mm (1–1.2 inches)
Width
335 mm (13.1 inches)
Depth
238 mm (9.37 inches)
Weight
1.95 kg (4.3 lbs)
Environmental Temperature range:
Operating
0° to 35° C (32° to 95° F)
Storage
–40° to 65° C (–40° to 149° F)
Relative humidity (maximum):
Operating
10% to 90% (non-condensing)
Storage
5% to 95% (non-condensing)
Maximum vibration (using a random-vibration spectrum that simulates user environment):
Operating
0.66 GRMS
Storage
1.3 GRMS
Maximum shock (measured with hard drive in head-parked position and a 2–ms half-sine pulse):
Operating
143 G
Storage
163 G
Altitude (maximum):
Operating
–15.2 to 3048 m (–50 to 10,000 ft)
Storage
–15.2 to 3048 m (–50 to 10,000 ft)
Airborne contaminant level
G2 or lower as defined by ANSI/ISA-S71.04-1985
Back to Contents Page
Battery
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Battery
1.
Follow the procedures in Before Working Inside Your Computer.
2.
Slide the battery lock latch on the left away from the battery.
3.
Slide the battery latch at the center toward the right.
4.
Slide the battery toward the back of the computer and remove.
Back to Contents Page
Coin-Cell Battery
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Coin-Cell Battery
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer.
Remove the hard drive from the computer.
Remove the optical drive from the computer.
Remove any WLAN card from the computer.
Remove the fan from the computer.
Remove any ExpressCards from the computer.
Remove the hinge cover from the computer.
Remove the keyboard from the computer.
Remove the display assembly from the computer.
Remove the palm rest from the computer.
Remove the system board from the computer.
13.
Insert scribe into slot and gently pry up the coin-cell battery.
14.
Remove the coin-cell battery.
Back to Contents Page
Display Bezel
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Display Bezel
1.
2.
Follow the procedures in Before Working Inside Your Computer.
Remove the display assembly from the computer.
3.
Remove the six rubber screw covers from the display bezel.
4.
Remove the six screws that secure the bezel to the display assembly.
5.
Remove the bezel from the display assembly.
Back to Contents Page
Camera
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Camera
1.
2.
3.
4.
Follow the procedures in Before Working Inside Your Computer.
Remove the display assembly from the computer.
Remove the display bezel from the display assembly.
Remove the display inverter from the display assembly.
5.
Remove the screw that secures the display camera to the display assembly.
6.
Lift the camera from its slot.
6.
Disconnect the display camera data cable.
7.
Remove the display camera from the display assembly.
Back to Contents Page
Display Assembly Hinges
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Display Assembly Hinges
1.
2.
3.
4.
5.
Follow the procedures in Before Working Inside Your Computer.
Remove the display assembly from the computer.
Remove the display bezel from the display assembly.
Remove the display inverter from the display assembly.
Remove the LCD display panel from the display assembly.
6.
Remove the six screws securing the hinges to the display panel assembly.
7.
Slide the hinges away from the display panel assembly.
Back to Contents Page
Display Inverter
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Display Inverter
1.
2.
3.
Follow the procedures in Before Working Inside Your Computer.
Remove the display assembly from the computer.
Remove the display bezel from the computer.
3.
Remove the screw that secures the display inverter to the display assembly.
4.
Disconnect the inverter power cable from the display assembly.
5.
Disconnect the inverter data cable from the display assembly.
6.
Remove the display inverter from the display assembly.
Back to Contents Page
LCD Display Panel
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the LCD Display Panel
1.
2.
3.
Follow the procedures in Before Working Inside Your Computer.
Remove the display assembly from the computer.
Remove the display bezel from the display assembly.
4.
Remove the two screws that secure the LCD display panel to the display assembly.
5.
Disconnect the power cable from the display assembly.
6.
Disconnect the data cable from the display assembly.
7.
Remove the LCD display panel from the display assembly.
Back to Contents Page
Display Assembly
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Display Assembly
1.
2.
3.
4.
5.
6.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer.
Remove the hard drive from the computer.
Remove the WLAN card from the computer.
Remove the hinge cover from the computer.
Remove the keyboard from the computer.
7.
Disconnect the antenna cables from the WLAN card.
8.
Draw the antenna cables through the system board.
9.
Disconnect the display data cable from the system board.
10.
Loosen and release the display grounding screw from the computer.
11.
Remove the four screws securing the display assembly to the base of the computer.
12.
Lift and remove the display assembly from the computer.
Back to Contents Page
Fan
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Fan
1.
2.
3.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer.
Remove the access panel from the computer.
4.
Disconnect the fan cable from the system board.
5.
Remove the two screws that secure the fan to the computer.
6.
Lift the fan and remove it from the computer.
Back to Contents Page
Fingerprint Reader
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Fingerprint Reader
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer.
Remove the hard drive from the computer.
Remove the WLAN card from the computer.
Remove the fan from the computer.
Remove any ExpressCards from the computer.
Remove the hinge cover from the computer
Remove the keyboard from the computer.
Remove the display assembly from the computer.
Remove the palm rest from the computer.
11.
Open the fingerprint reader cable retaining clip.
12.
Open the fingerprint reader cable retaining clip.
13.
Remove the fingerprint reader cable.
14.
Remove the screw that secures the fingerprint reader bracket to the computer chassis.
15.
Remove the fingerprint reader bracket.
16.
Remove the fingerprint reader from the palm rest.
Back to Contents Page
Hinge Cover
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Hinge Cover
1.
2.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer
3.
Use a plastic scribe gently to pry the back side of the hinge cover away from the base of the computer.
4.
Starting on the right side, separate the hinge cover from the base of the computer.
5.
Continue to separate the hinge cover from the computer working from right to left, then remove the hinge cover.
Back to Contents Page
Hard Drive
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Hard Drive
1.
2.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer.
3.
Loosen the captive screw that secures the hard drive access panel to the bottom of the computer.
4.
Lift the hard drive access panel.
5.
Remove the hard drive access panel from the computer.
6.
Slide the hard drive toward the right side of the computer to disengage the drive from its connector.
7.
Lift the hard drive and remove it from the computer.
Back to Contents Page
Keyboard
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Keyboard
1.
2.
3.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer.
Remove the hinge cover from the computer.
4.
Remove the two screws that secure the keyboard to the computer.
5.
Lift the back edge of the keyboard slightly and slide the keyboard toward the back of the computer.
6.
Open the keyboard data cable clip to free the ribbon cable.
7.
Remove the keyboard data cable from the clip.
8.
Remove the keyboard from the computer.
Back to Contents Page
Memory
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing Memory Modules
NOTE: DIMM A is the module closest to the system board. You cannot remove DIMM A until DIMM B is removed. If only 1 DIMM is installed, it should
always be installed in the DIMM A slot. If only 1 DIMM is installed, moving memory from DIMM A to DIMM B will disable AMT (if currently enabled).
1.
2.
3.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer.
Remove the access panel from the computer.
4.
For each memory module present in your computer, use your fingertips carefully to spread apart the securing clips on each end of the memory module
connector until the memory module pops up.
5.
Remove the memory module from the socket.
Back to Contents Page
Optical Drive
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Optical Drive
1.
2.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer.
3.
Remove the screw that secures the optical drive in place.
4.
Insert a plastic scribe into the notch and slide the optical drive slightly out of the computer.
6.
Remove the optical drive from the computer.
Back to Contents Page
Palm Rest
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Palm Rest
1.
2.
3.
4.
5.
6.
7.
8.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer.
Remove the access panel from the computer.
Remove the heat sink from the computer.
Remove the hinge cover from the computer.
Remove the hard drive from the computer.
Remove the optical drive from the computer.
Remove the display assembly from the computer.
9.
Remove the thirteen screws that secure the palm rest to the bottom of the computer.
10.
Turn over the computer and release the fingerprint reader data cable clip.
11.
Remove the fingerprint reader data cable from the clip.
12.
Release the touch pad data cable clip.
13.
Remove the touch pad data cable from the clip.
14.
Release the multimedia button board data cable clip.
15.
Remove the multimedia button board data cable from the clip.
14.
Remove the eleven screws that secure the palm rest to the top of the computer.
16.
Remove the palm rest from the computer.
Back to Contents Page
Access Panel
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Access Panel
1.
2.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer.
3.
Remove the screw that secures the access panel to the computer.
4.
Slide the access panel toward the front of the computer.
5.
Remove the access panel.
Back to Contents Page
Heat Sink and Processor
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Heat Sink and Processor
1.
2.
3.
4.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer.
Remove the access panel from the computer.
Remove the fan from the computer.
5.
Loosen the four captive screws that secure the heat sink to the computer.
6.
Lift the edge of the heat sink that is closest to the center of the computer.
7.
Slide the heat sink toward the center of the computer, then lift up the heat sink and remove it from the computer.
8.
Using a flathead screw driver, rotate the processor cam counterclockwise.
9.
Lift the processor straight up from its socket, taking care not to bend any of the processor pins.
Back to Contents Page
Speaker Assembly
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Speaker Assembly
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer.
Remove the hard drive from the computer.
Remove the optical drive from the computer.
Remove the WLAN card from the computer.
Remove the access panel from the computer.
Remove the fan from the computer.
Remove any ExpressCards from the computer.
Remove the hinge cover from the computer.
Remove the keyboard from the computer.
Remove the display assembly from the computer.
Remove the palm rest from the computer.
Remove the system board from the computer.
14.
Remove the two screws that secure the speaker assembly to the chassis.
15.
Remove the speaker assembly from the computer.
Back to Contents Page
System Board
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the System Board
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Follow the procedures in Before Working Inside Your Computer.
Remove any ExpressCards and SD cards from the computer.
Remove the battery from the computer.
Remove the access panel from the computer.
Remove the hinge cover from the computer.
Remove the keyboard from the computer.
Remove the hard drive from the computer.
Remove the optical drive from the computer.
Remove the fan from the computer.
Remove the heat sink and processor from the computer.
Remove the memory modules from the computer.
Remove the coin-cell battery from the computer.
Remove the Bluetooth module from the computer.
Remove the WLAN card from the computer.
Remove the display assembly from the computer.
Remove the palm rest from the computer.
17.
Disconnect the speaker cable from the system board.
18.
Disconnect the data cable from the system board.
19.
Disconnect the USB board data cable from the system board.
20.
Remove the power cable from the system board.
21.
Remove the two screws that secure the system board to the computer chassis.
22.
Remove the system board from the computer chassis.
Back to Contents Page
Wireless Local Area Network (WLAN) Card
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the WLAN Card
1.
2.
3.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer.
Remove the hard drive from the computer.
4.
Disconnect the antenna cables from the WLAN card.
5.
Remove the screw that secures the WLAN card to the system board.
6.
Remove the WLAN card from the computer.
Back to Contents Page
Internal Card With Bluetooth® Wireless Technology
Dell™ Vostro™ 1320 Service Manual
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
Removing the Internal Card With Bluetooth Wireless Technology
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Follow the procedures in Before Working Inside Your Computer.
Remove the battery from the computer.
Remove the hard drive from the computer.
Remove the WLAN card from the computer.
Remove the fan from the computer.
Remove any ExpressCards from the computer.
Remove the hinge cover from the computer.
Remove the keyboard from the computer.
Remove the display assembly from the computer.
Remove the palm rest from the computer.
11.
Lift the Bluetooth module from its slot in the computer.
12.
Disconnect the Bluetooth module from its data cable and set the module aside.
13.
Disconnect the data cable from the system board.
14.
Remove the data cable from the computer.
15.
Remove the Bluetooth module from the computer.
Back to Contents Page
Working on Your Computer
Dell™ Vostro™ 1320 Service Manual
Before Working Inside Your Computer
Recommended Tools
Turning Off Your Computer
After Working Inside Your Computer
Before Working Inside Your Computer
Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted,
each procedure included in this document assumes that the following conditions exist:
l
l
l
You have performed the steps in Working on Your Computer.
You have read the safety information that shipped with your computer.
A component can be replaced or—if purchased separately—installed by performing the removal procedure in reverse order.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is
not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface, such as a connector on the back of the computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal
mounting bracket. Hold a component such as a processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have connectors with locking
tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep
them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented
and aligned.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
To avoid damaging your computer, perform the following steps before you begin working inside the computer.
1.
2.
3.
Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.
Turn off your computer (see Turning Off Your Computer).
If the computer is connected to a docking device (docked) such as the optional Media Base or Battery Slice, undock it.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.
4.
5.
6.
Disconnect all network cables from the computer.
Disconnect your computer and all attached devices from their electrical outlets.
Close the display and turn the computer upside-down on a flat work surface.
CAUTION: To avoid damaging the system board, you must remove the main battery before you service the computer.
7.
8.
9.
10.
Remove the main battery (see Removing the Battery).
Turn the computer top-side up.
Open the display.
Press the power button to ground the system board.
CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the display.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back
of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal
components.
11.
12.
Remove any installed ExpressCards or Smart Cards from the appropriate slots.
Remove the hard drive (see Removing the Hard Drive).
Recommended Tools
The procedures in this document may require the following tools:
l
l
l
l
l
Small flat-blade screwdriver
#0 Phillips screwdriver
#1 Phillips screwdriver
Small plastic scribe
Flash BIOS update program CD
Turning Off Your Computer
CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.
1.
Shut down the operating system:
l In Windows Vista:
Click Start
l
, then click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down.
In Windows XP:
Click Start® Turn Off Computer® Turn Off.
The computer turns off after the operating system shutdown process is complete.
2.
Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut
down your operating system, press and hold the power button for about 4 seconds to turn them off.
After Working Inside Your Computer
After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer.
CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for
other Dell computers.
1.
2.
Connect any external devices, such as a port replicator, battery slice, or media base, and replace any cards, such as an ExpressCard.
Connect any telephone or network cables to your computer.
CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer.
3.
4.
5.
Replace the battery.
Connect your computer and all attached devices to their electrical outlets.
Turn on your computer.