Installation Operation and Maintenance

Installation Operation and Maintenance
MARVEL REFRIGERATED DRAWERS
Installation
Operation
and
Maintenance
Instructions
Refrigerated Drawer Models
60RDE
80RDE
6ORDE
TABLE OF CONTENTS
Unpacking your refrigerated drawer unit................2
Removing the packaging....................................2
Warranty Registration..........................................2
Installing your refrigerated drawer unit...................3
Selecting the location.........................................3
Outdoor Installation...........................................3
Cabinet Clearances............................................3
Leveling legs......................................................3
Grounding method.............................................3
Electrical Requirements.......................................3
Installing the anti tip device............................ ... 4
Dimensions Indoor Model 60RDE.......................... 5
Recommended Rough in Opening Dimensions
Indoor Model 60RDE........................................ 5
Dimensions Indoor Model 60RDE Overlay Door.. .. 6
Recommended Rough in Opening Dimensions
Indoor Model 60RDE Overlay Door.....................6
Dimensions Outdoor Model 6ORDE...................... 7
Recommended Rough in Opening Dimensions
Outdoor Model 6ORDE..................................... 7
Dimensions Indoor Model 80RDE.......................... 8
Recommended Rough in Opening Dimensions
Indoor Model 80RDE..........................................8
Dimensions Indoor Model 80RDE Overlay Door......9
Recommended Rough in Opening Dimensions
Indoor Model 80RDE Overlay Door....................9
Full Overlay Panel Installation Instructions..............10
Using Your Refrigerated Drawers...........................12
Starting Your Appliance.......................................12
Set Your Temperature Mode................................12
Set the Desired Temperature................................12
Load Your Appliance...........................................12
Interior Light.......................................................12
Defrost Cycle......................................................12
Sabbath Mode....................................................12
Warning Alarms..................................................13
Sentry System™ Quick Reference...........................14
Care and Cleaning...............................................16
E-Z Store Storage System (Optional).......................16
Drawer Dividers (Optional)...................................16
Troubleshooting Guide..........................................17
Obtaining Service.................................................17
Household Product Warranty..................................18
1
Important Safety Instructions
Warnings and safety instructions appearing in this
guide are not meant to cover all possible conditions and situations that may occur. Common sense,
caution, and care must be exercised when installing,
maintaining, or operating this appliance.
Recognize Safety Symbols,
Words, and Labels.
CAUTION-Hazards or unsafe practices which could
result in personal injury or property or product damage.
WARNING-Hazards or unsafe practices which could
result in personal injury.
NOTE-Important information to make a problem free
installation.
UNPACKING YOUR REFRIGERATED DRAWERS
Remove Packaging
Your refrigerated drawers have been packed for shipment with all parts that could be damaged by movement securely fastened. Cut the banding material at the
bottom of the carton, unfold the cartoning at the bottom
and remove the carton from the appliance. Remove the
plastic bag, styrofoam corner posts and any tape holding
the drawers closed and internal components in place.
The owners manual is shipped inside the drawer in a
plastic bag along with the warranty registration card.
Important
Keep your carton packaging until your refrigerated drawers have been thoroughly inspected and found to be in
good condition. If there is damage, the packaging will
be needed as proof of damage in transit. Afterwards
please dispose of all items responsibly in particular the
plastic bags which can be a suffocation hazard.
Warranty Registration
It is important you send in your warranty registration card
immediately after taking delivery of your refrigerated drawers
or you can register online at www.marvelrefrigeration.com.
The following information will be required when registering
your unit.
Model Number
Serial Number
Date of Purchase
Dealers name and address
The model number and serial number ca be found on the
serial plate which is located on the bottom of the cabinet
liner in the left front corner. Open the bottom drawer to full
extension to view it.
Note to Customer
This merchandise was carefully packed and thoroughly
inspected before leaving our plant. Responsibility for
its safe delivery was assumed by the retailer upon acceptance of the shipment. Claims for loss or damage
sustained in transit must be made to the retailer.
DO NOT RETURN DAMAGED MERCHANDISE TO THE
MANUFACTURER - FILE THE CLAIM WITH THE RETAILER.
Help Prevent Tragedies
Child entrapment and suffocation are not problems of the
past. Junked or abandoned refrigerators are still dangerous - even if they sit out for “just a few days”.
If you are getting rid of your old refrigerator, please follow
the instructions below to help prevent accidents.
If the unit was shipped or has been laying on its back for
any period of time allow the refrigerator to sit upright for
a period of at least 24 hours before plugging in. This will
assure oil returns to the compressor. Plugging the refrigerator in immediately may cause damage to internal
parts.
Before you throw away your old refrigerator or freezer:
• Take off the doors or remove the drawers.
• Leave the shelves in place so children may not easily
climb inside.
2
INSTALLING YOUR REFRIGERATED DRAWERS
Select Location
The proper location will ensure peak performance of your
appliance. We recommend a location where the unit will
be out of direct sunlight and away from heat sources. To
assure your product performs to specifications the recommended installation location temperature range is from 55
to 100°F (13 to 38°C).
Leveling Legs
Adjustable legs at the front and rear corners of the unit
should be set so the unit is firmly positioned on the floor
and level from side to side and front to back. Turn leveling
legs clockwise to raise unit, counterclockwise to lower it.
(See Figure 1).
Outdoor Installation
Only the 6ORDE model is suitable for outdoor installations.
A ground fault circuit interrupter electrical receptacle is to
be used to supply electrical power to the refrigerator for
outdoor applications. Contact an electrician if you need
to install one to supply electrical power to your outdoor
refrigerator. Do not install in an environment where the unit
will be exposed to direct sun exposure as this may result in
unsatisfactory performance.
• Do not splash or spray water from a hose on the refrigerator! Doing so may cause an electrical shock,
which may result in severe injury or death.
• This unit should not, under any circumstances, be
ungrounded.
Cabinet Clearance
Ventilation is required from the bottom front section of the
unit. Keep this area open and clear of any obstructions.
Adjacent cabinets and countertop can be installed around
the unit as long as the grille and drawer access remain
unobstructed.
Front Grille
Do not obstruct the front grille. The openings within the
front grille provide air to flow into and exit from the refrigerator condenser. For this reason it is important this area to
not be obstructed and be kept clean.Marvel does not recommend the use of custom made grilles as air flow may be
restricted because of inadequate openings. (See Figure 1).
Grounding Method
This product is factory equipped with a power supply cord
that has a three-pronged, grounded plug. It must be
plugged into a mating grounding type receptacle in accordance with the National Electrical Code and applicable local codes and ordinances (see Figure 2). If the circuit does
not have a grounding type receptacle, it is the responsibility
and obligation of the customer to exchange the existing
receptacle in accordance with the National Electrical Code
and applicable local codes and ordinances. The third
ground prong should not, under any circumstances, be cut
or removed.
Electrical Connection
115 volts, 3.3 amps running max. 15 amp dedicated circuit
required. 3 prong grounded receptacle required.
Do not use an extension cord
with this appliance.
Front Grille,
keep this
area open.
Figure 2
Figure 1
3
Leveling Legs
INSTALLING THE ANTI-TIP DEVICE
Remove these screws to seperate
upper and lower sections of anti-tip
bracket.
Anti - Tip Device
A cabinet “anti–tip” device is mounted to the back of your
refrigerated drawer unit. If your installation is a built – in
undercounter application with a countertop directly above
the unit this item can be removed, it does not need to be
applied. If your unit is a freestanding application with no
countertop directly above the top of the unit, you must
apply this feature to prevent the unit from tipping forward
when the drawers are pulled out. The anti–tip device
is installed on the back of the unit. The anti–tip device
reduces the chance of personal injury as well as property
damage when properly installed between the back of
the unit and the adjacent wall. Please see the following
instructions for installing the anti-tip device.
1.
2.
3.
4.
5.
6.
Push the unit against the wall so the anti-tip
bracket is flush to the wall adjacent to the back
panel. Level the unit with the leveling legs provided
in the cabinet bottom. (See Leveling Legs on
page 3).
Using a pencil and the bracket as a template, trace
the bracket on the wall, making sure 2 of the screw
holes are aligned with a stud in the wall.
Pull the unit away from the wall.
Remove the screws that connect the upper and
lower sections of the anti-tip bracket.
Place the bracket on the wall and mark and drill
3/16” dia. Pilot holes for the provided ¼” lag
screws. Mount the lower section to the wall with the
¼” lag screws.
Move the unit into place aligning the screw holes
between the upper and lower brackets and secure
with the screws removed in step 4.
To Refrigerated
Drawer Cabinet
To Wall
Figure 4
1/4” Lag screws
into wall
Anti-Tip device
Figure 3
4
Dimensions Indoor Model 60RDE
26-3/8”
(67 cm)
24-1/4”
(61.6 cm)
23-7/8”
(60.7 cm)
22”
(55.9 cm)
1-7/8”
(4.8 cm)
Anti tip Bracket must be
installed for freestanding applications. Can be removed
for built in applications.
34-1/4” to 34-1/2”
(87 to 87.6 cm)
Front and Rear
Leveling Legs
46” Drawer fully opened
(116.8 cm)
48-1/8” Drawer fully opened
(122.2 cm)
Recommended Rough In Opening Dimensions, Indoor Model 60RDE
Alternate
outlet location
in adjacent
cabinetry.
34-1/2”
(87.6 cm)
Electrical Requirements: 115 volts,
3.3 amps running max. 15 amp
dedicated circuit required. 3 prong
grounded receptacle required.
*24” (61 cm)
standard cabinet depth
*Depth dimension may very depending on
each individual installation.
5
24”
(61 cm)
Power outlet can be located in the
back wall behind unit. Add 1” to
depth for thickness of plug, or recess
outlet 1” into the wall. Power outlet
can also be installed in adjacent
cabinetry with a cutout for routing of
power cord. Follow all local building
codes when installing electrical and
unit.
Product weight = 170 lbs. (77.1 kg.)
Dimensions for Indoor Model 60RDE Overlay Door
23-3/8” Not including
(59.4 cm) custom panel
23-7/8”
(60.7 cm)
22”
(55.9 cm)
1-7/8”
(4.8 cm)
Anti tip Bracket must be
installed for freestanding applications. Can be removed
for built in applications.
34-1/4” to 34-1/2”
(87 to 87.6 cm)
Front and Rear
Leveling Legs
Drawer fully opened
45-1/8” Not including
(114.6 cm) custom panel
Recommended Rough In Opening Dimensions, Indoor Model 60RDE Overlay Door
Alternate
outlet location
in adjacent
cabinetry.
34-1/2”
(87.6 cm)
Electrical Requirements: 115 volts,
3.3 amps running max. 15 amp
dedicated circuit required. 3 prong
grounded receptacle required.
*24” (61 cm)
standard cabinet depth
*Depth dimension may very depending on
each individual installation.
24”
(61 cm)
Power outlet can be located in the
back wall behind unit. Add 1” to
depth for thickness of plug, or recess
outlet 1” into the wall. Power outlet
can also be installed in adjacent
cabinetry with a cutout for routing of
power cord. Follow all local building
codes when installing electrical and
unit.
Product weight = 170 lbs. (77.1 kg.)
6
Dimensions for Outdoor Model 6ORDE
26-3/8”
(67 cm)
24-1/4”
(61.6 cm)
23-7/8”
(60.7 cm)
22”
(55.9 cm)
1-7/8”
(4.8 cm)
Anti tip Bracket must be
installed for freestanding applications. Can be removed
for built in applications.
34-1/4” to 34-1/2”
(87 to 87.6 cm)
Front and Rear
Leveling Legs
46” Drawer fully opened
(116.8 cm)
48-1/8” Drawer fully opened
(122.2 cm)
Recommended Rough In Opening Dimensions, Outdoor Model 6ORDE
Alternate
outlet location
in adjacent
cabinetry.
34-1/2”
(87.6 cm)
*24” (61 cm)
standard cabinet depth
*Depth dimension may very depending on
each individual installation.
7
24”
(61 cm)
Electrical Requirements: 115 volts,
3.3 amps running max. 15 amp
dedicated circuit required. 3 prong
grounded receptacle required.
Power outlet can be located in the
back wall behind unit. Add 1” to
depth for thickness of plug, or recess
outlet 1” into the wall. Power outlet
can also be installed in adjacent
cabinetry with a cutout for routing of
power cord. Follow all local building
codes when installing electrical and
unit.
A ground fault circuit interrupter
electrical receptacle is to be used
to supply electrical power to the
refrigerator for outdoor applications.
Contact an electrician if you need to
install one to supply electrical power
to your outdoor refrigerator.
Product weight = 170 lbs. (77.1 kg.)
Dimensions for Indoor Model 80RDE
26-3/8”
(67 cm)
24-1/4”
(61.6 cm)
29-7/8”
(75.9 cm)
22”
(55.9 cm)
1-7/8”
(4.8 cm)
Anti tip Bracket must be
installed for freestanding applications. Can be removed
for built in applications.
34-1/4” to 34-1/2”
(87 to 87.6 cm)
Front and Rear
Leveling Legs
46” Drawer fully opened
(116.8 cm)
48-1/8” Drawer fully opened
(122.2 cm)
Recommended Rough In Opening Dimensions, Indoor Model 80RDE
Alternate
outlet location
in adjacent
cabinetry.
34-1/2”
(87.6 cm)
Electrical Requirements: 115 volts,
3.3 amps running max. 15 amp
dedicated circuit required. 3 prong
grounded receptacle required.
*24” (61 cm)
standard cabinet depth
*Depth dimension may very depending on
each individual installation.
30”
(76.2 cm)
Power outlet can be located in the
back wall behind unit. Add 1” to
depth for thickness of plug, or recess
outlet 1” into the wall. Power outlet
can also be installed in adjacent
cabinetry with a cutout for routing of
power cord. Follow all local building
codes when installing electrical and
unit.
Product weight = 195 lbs. (88.4 kg.)
8
Dimensions for Indoor Model 80RDE Overlay Door
23-3/8” Not including
(59.4 cm)custom panel
29-7/8”
(75.9 cm)
22”
(55.9 cm)
1-7/8”
(4.8 cm)
Anti tip Bracket must be
installed for freestanding applications. Can be removed
for built in applications.
34-1/4” to 34-1/2”
(87 to 87.6 cm)
Front and Rear
Leveling Legs
Drawer fully opened
45-1/8” Not including
(114.6 cm) custom panel
Recommended Rough In Opening Dimensions, Indoor Model 80RDE Overlay Door
Alternate
outlet location
in adjacent
cabinetry.
34-1/2”
(87.6 cm)
Electrical Requirements: 115 volts,
3.3 amps running max. 15 amp
dedicated circuit required. 3 prong
grounded receptacle required.
*24” (61 cm)
standard cabinet depth
*Depth dimension may very depending on
each individual installation.
9
30”
(76.2 cm)
Power outlet can be located in the
back wall behind unit. Add 1” to
depth for thickness of plug, or recess
outlet 1” into the wall. Power outlet
can also be installed in adjacent
cabinetry with a cutout for routing of
power cord. Follow all local building
codes when installing electrical and
unit.
Product weight = 195 lbs. (88.4 kg.)
FOR MODELS 60RDE and 80RDE WITH OVERLAY PANELS
INSTALLATION INSTRUCTIONS
Determine Wood Screw Requirements
1. A #8 pan head wood screw should be used to properly secure the overlay panel. A total of 8 screws per
drawer for the 60 unit and 10 screws per drawer for
the 80 unit will be required.(See Figure 9). Necessary
screws are supplied with unit.
2. Use only pan head screws.
3. If your overlay panel is thinner than 5/8” (15.9 mm)
you will need to purchase shorter screws.
Figure 6
Figure 5
Figure 7
Step 1: Remove Drawers from unit.
1. Remove drawer from the unit. Begin by pulling out the
drawer. Locate the drawer lock which can be found
on the outside of the cabinet slide (see Figure 5). Push
the back of the drawer lock forward and then down,
releasing the drawer from the cabinet slide (see Figure
6). Repeat this on the opposite side of the drawer. Lift
the drawer up from the slides at a 90 degree angle to
fully extricate the drawer from the cabinet (See Figure
7).
2. Remove the gasket from the drawer front. Do this by
pulling the gasket out of the channel that holds it to the
drawer front. This will expose the clearance holes for
mounting the overlay panel. (See Figure 8).
.35/.31
(9mm/7.5mm)
Gasket
Figure 8
Figure 9
.50
(12.5)
10
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Step 2: Size the Overlay Panel
Cut the overlay panel to the dimensions shown below. Use
Figure 10 for the 60RDE Drawer, and Figure 11 for the
80RDE drawer.
Panel thickness
Step 4: Attach the Overlay Panel to the Drawer
1. Set the overlay panel on drawer front face and align
edges. (See Figure 12 below). Clamp panel in position and mark pilot hole locations. Pick the required
pilot hole size from “Table A” below and drill the pilot
holes ensuring not to drill all the way through the
overlay panel.
Table A: Pilot Hole Drill Sizes for Wood Screws
23.63”
(600.2 mm)
Material Type
#8 Wood Screw
Hardwood
3/32 Dia. Pilot Hole
Softwood
5/64 Dia. Pilot Hole
2. Insert wood screws through clearance holes and
tighten to secure ovelay panel.
3. Reinstall gasket into channel. Make sure the corners
are fully inserted.
15.19”
(385.83 mm)
Figure 10
Face of 60RDE
Overlay Panel
Step 5: Reinstall the Drawers
1. Fully extend drawer slides and place drawer on
slides. Be sure that drawer sits evenly on both slides.
2. Lock drawers into drawer slides. Push drawer locks
down and then back to relock the drawer into the
slide.
Screw clearance
hole through
gasket extrusion
Panel thickness
29.63”
(752.6 mm)
Overlay panel
flush with
edges of drawer
front
15.19”
(385.83 mm)
Figure 11
Face of 80RDE
Overlay Panel
Figure 12
Using clearance holes in
gasket channel mark
hole locations onto panel
11
USING YOUR REFRIGERATOR DRAWERS
LED
Figure 13
37
Set
Start Your Appliance
Your refrigerated drawers have been fitted with a Sentry
System™ refrigeration monitor. It is located at the top front
of the cabinet and can be accessed by opening the top
drawer.Your appliance will start upon initial plug-in. On
start the Sentry System™ monitor will flash amber.This is
normal. Press the “ON/OFF” button and the appliance
resets and the LED turns green. (Refer to Figure 13 above).
Set Your Temperature Mode
This product can display either Fahrenheit or Celsius. To
do so, press the “°F/C” button on the display panel to
change from one to the other.
Set the desired temperature
The available temperature range of the unit is from 33° to
47°F (1° to 8° C). This range allows flexibility of temperature preferences and provides the ideal storing and serving
temperatures. The temperature is initially set in the factory
at 37° F (3° C). The temperature set point can be lowered
or raised by first pushing the “SET” button on the display
pad. A “SET” icon will be displayed in the temperature
display. Pressing and releasing either the “WARMER” or
“COLDER” buttons located on the display pad will raise or
lower the set temperature by one (1) degree at a time. As
with any refrigeration product, there will be slight temperature variance at different locations within the cabinet.
Defrost Cycle
In order to maintain optimal performance, your refrigerator
must periodically enter a defrost cycle to clear frost buildup.
During the defrost cycles, the display will show DEF, and
changes to setpoint and °F/°C setting may not be made.
Sabbath Mode
Your refrigerated drawers are equipped with a Sabbath
Mode feature. By activating this mode, you will be disabling all displays, audible alarms and lights. To activate
the Sabbath Mode, press and hold the “SET” button while
pressing the “°F/C” button four (4) times within seven (7)
seconds. To disable the Sabbath Mode, repeat the process.
The Sabbath Mode will deactivate automatically after 72
hours.
Load Your Appliance
Load your appliance with your desired items. Please note
that it may take up to 24 hours for your refrigerator to
reach the desired temperature once loaded. This will primarily depend on the amount of contents loaded into the
refrigerator and the amount of opening and closings of the
drawers. Consider this when initially loading the drawers.
Best results will be obtained by first allowing the drawers
to “pull down” to your set temperature before loading the
drawers.
Interior Light
The upper and lower interior lights make it easy to view
your food and beverages. The light will always come on
when either drawer is opened, except when unit is in Sabbath Mode.
12
USING YOUR REFRIGERATED DRAWERS
Figure 14
37
LED
Set
Warning Alarms
The Sentry System™ monitor will let you know if your unit
is not functioning properly for the following reasons. Door
ajar, high or low temperature, and power failure. These
alarms are explained below.
Door Ajar Alarm
If the drawer has been left open for over five (5) minutes,
the alarm will sound and the LED will flash green. This will
stop as soon as the drawer is closed, or can be reset by
pressing the “ON/OFF” button.
High and Low Temperature
If your unit reaches temperatures outside normal operating
temperatures for your set point for more than one (1) hour,
an alarm will sound and the LED will flash red. This will
warn you that your contents have seen temperatures that
may not be conducive for long-term storage. This alarm
can be reset by pressing the “ON/OFF” button.
Power Failure
If your unit experiences a power failure, the LED will flash
amber until the alarm is reset by pressing the “ON/OFF”
button.
Reset Alarms
Press the “ON/OFF” button for approximately one (1) second. This will reset all audible and display alarms when
the button is released.
Enable/Disable Sentry System™ Alarms
Press and hold the “SET” key for five (5) seconds to enable or disable the Sentry System™alarms. LED will display
a steady green when enabled or a steady amber when
disabled.
13
Quick Reference Guide
The quick reference guide on page 14 and 15 can be
removed from this manual and retained near the appliance for quick access to the Sentry System™ functions.
14
Note that although pressing the “ON/OFF” key resets the alarms, the alarm will
resume if the “alarm condition” still exists.
Close drawer to reset “DOOR AJAR” alarm. Press the “ON/OFF” key to reset
all other alarms.
Reset Alarms
Enable / Disable Sentry
System™alarms
LED displays a steady green when alarms are enabled. LED displays a steady amber
when they are disabled.
LED will flash amber whenever power is interupted to unit. There is no audible signal.
Press ON/OFF button to reset alarm.
No action required if Sentry System™is enabled. NOTE: Alarm will occur
upon initial installation, since unit was run at the factory to verify quality, this
is normal.
Power Failure Alarm
Press and hold the “SET” key for five (5) seconds to enable or disable the
Sentry System™ alarms.
Alarm will sound 6-times every minute and LED will flash red if product temperature
excursions occur for a duration outside acceptable limits.
No action is required if Sentry System™is enabled. NOTE: This alarm may
occur when changing set-points and/or high usage, this is normal.
High/Low Temp Alarm
Drawer Ajar Alarm
Audible alarm will sound 3 times every 30 seconds, the LED will flash green. Close
drawer to reset alarm.
Sentry System™ LED displays a steady green when Sentry System™ is enabled.
No action required. System monitoring is automatically enabled unless system has been disabled (see below).
Sentry System™ alarms
No action required if Sentry System™ is enabled.
The display will flash “SA” seven (7) times, then the unit will enter Sabbath Mode. The
display, audible alarms, LED, and lights will be disabled. Sabbath Mode will automatically time-out in 72 hours., or can be exited by repeating the enabling process.
Press and hold the “SET” key while pressing the “°F/°C” key four (4) times in
seven (7) seconds.
Sabbath Mode
Temperature variation in “compartment” air, above and below set-point, is a normal
effect of refrigeration system cycling on and off. Stored items will not experience the
full temperature swing of the compartment air due to the dampening effect of their
thermal mass.
The display represents real time monitoring. Some temperature fluctuation
around the set-point will be noticeable as the refrigeration system cycles on
and off to maintain the desired temperature.
i.e. 55°F = 13°C
“SET” will appear in temperature display when in set-point mode. “SET” mode will
automatically time-out in ten (10) seconds if no keypad activity occurs, or you may exit
“SET” mode by pressing the “SET” key.a second time.
To adjust the temperature set-point, press the “SET” key and current set-point
will be displayed. Use the “WARMER” or “COLDER” keys to adjust set-point
temperature.
Pressing the “°F/°C” key will toggle the display between Fahrenheit and Centigrade temperature display.
The display will be blank when the refrigeration system is off. Lights will still function,
but will time-out in 15 minutes after each activation if drawer is left open, to prevent
overheating.
Control Confirmation / Comment
Pressing and holding the “On/Off” key for five seconds will turn the unit
“ON” or “Off”.
Function Access
Select °F or °C Display
Display “Actual” Temperature
Adjust and View Temperature
set-point
Turn Unit On & Off
Function
Note: All keypad presses are confirmed with an audible tone when released.
Sentry System™ “Basic” Function “Quick” Reference
15
Service Diagnostics
Error Codes
Condenser fan motor fault, (high/low amps)
Evaporator thermistor “sensor B” fault, (out of range)
Display thermistor “sensor A” fault, (out of range)
E3
E4
Display Error Code Reference:
The microprocessor in the control continually monitors critical refrigeration
system components for proper operation. If component parameters exceed
normal operation specifications, the display will automatically flash the
respective error code as follows:
To enter and exit Service Diagnostics Mode, press and hold the “WARMER”
key while pressing the “COLDER” key four (4) times in five (5) seconds.
Service Diagnostics Mode will automatically exit after five (5) minutes of no
keypad entry.
Please call a qualified service technician if any of these codes are displayed.
Compressor fault, (high/low amps)
Temperature Sensor, Lower
Compressor
Interior / Ice Maker Fan
Reverse Gas Solenoid
Condenser Fan
Mullion Heater
Door A Sense
Door B Sense
Door C Sense
1
2
3
4
5
6
7
8
9
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
1-
0-
OK
90
80
70
60
50
40
30
20
10
00
Off/
Open
91
81
71
61
51
41
31
21
11
01
On/
Shorted
NOTE: The Door Sense is located between the Upper Compartment Display
and the “ON/OFF” key and can be tested with any magnet.
Door sense “C” (Test #9) is in the menu but not available on drawer units.
Temperature Sensor, Upper
Component Description
0
Test #
Available Status Indicators
Service Diagnostics Mode enables service technicians to identify the firmware
and software versions, test status of “model specific” system components and
sensors, and change state of components where applicable, (i.e. -compressor
“ON/OFF” etc.). While in Service Diagnostics Mode, tests are incremented by
pressing the “SET” key and specific component state can be changed to “on”
or “off” by pressing the “WARMER” or “COLDER” keys respectively. The following component tests are available:
Show Room Mode
E2
Show Room Mode will disable the refrigeration system and fans while allowing the internal lights, display, and user interface panel to function. Lights will
time-out after 15 minutes of continuous on-time while in Show Room Mode
as a safety feature. The 15 minute light on time can be reactivated by closing
and opening the door or by pressing the “LIGHT” key.
Enable the showroom mode by pressing and holding the “ON/OFF” key
while performing a “Power On Reset” (POR). i.e. disconnect and reconnect
the power supply to the unit. Exit Showroom Mode by initiating a POR only.
E1
Control Confirmation / Comment
Function Access
Function
Note: All keypad presses are confirmed with an audible tone when released.
Sentry System™ “Troubleshooting” Function “Quick” Reference
CARE AND CLEANING OF YOUR REFRIGERATED DRAWERS
Condenser
The machine compartment located beneath the cabinet
does not require frequent cleaning; however, satisfactory
performance depends on adequate ventilation. Be sure
nothing obstructs the required air flow openings in front of
the cabinet. At least once or twice a year, brush or vacuum
lint and dirt from the front grille openings. See Figure 1 on
page 3.
Cabinet
The painted cabinet can be washed with either a mild soap
and water and thoroughly rinsed with clear water. NEVER
use abrasive scouring cleaners.
Interior
Wash interior compartment with mild soap and water. Do
NOT use an abrasive cleaner, solvent, polish cleaner or undiluted detergent.
Care of Unit
1. Avoid leaning on the drawer fronts, you may bend the
drawer slides or tip the unit.
2. Exercise caution when sweeping, vacuuming or mopping near the front of the unit. Damage to the grille can
occur.
3. Periodically clean the interior of the unit as needed.
4. Periodically check and/or clean the front grille as needed.
AVAILABLE OPTIONS FOR YOUR MARVEL DRAWER REFRIGERATOR
E-Z Stor Storage System
Removable stainless steel bins with clear plastic lids can
be moved to prep, cook, or serving areas as desired.
Available for 60RDE and 80RDE upper and lower drawers.
P/N 42245441 for 60 upper or lower drawers
P/N 42245442 for 80 upper drawer
P/N 42245443 for 80 lower drawer
For further information on available options visit the Marvel website at www.marvelrefrigeration.com or contact your
Marvel dealer.
When installing these options in the drawers the standard
drawer divider will have to be removed.
Plastic lids
Stainless steel bins
Drawer Dividers
Fully adjustable stainless steel drawer dividers allow for
optimum storage and organization of storage space.
P/N 42245444 for 60RDE upper drawer
P/N 42245445 for 60RDE lower drawer
P/N 42245446 for 80RDE upper drawer
P/N 42245447 for 80RDE lower drawer
Stainless steel rods
Stainless steel divider fits
on top of drawer sides.
Adjustment knob
Figure 15
E-Z-Store Storage System
Figure 16
Drawer Dividers
16
TROUBLESHOOTING YOUR REFRIGERATED DRAWERS
Before You Call for Service
If the unit appears to be malfunctioning, read through this
manual first. If the problem persists, check the troubleshooting guide below. Locate the problem in the guide and refer
to the cause and its remedy before calling for service. The
problem may be something very simple that can be solved
without a service call. Some remedies listed in the Troubleshooting Guide are very complex. Consulting or contracting
a qualified service technician may be necessary
If Service is Required:
• If the product is within the first year warranty period
please call Marvel Customer Service at 800.223.3900
for directions on how to obtain warranty coverage in your
area.
• If the product is outside the first year warranty period,
Marvel Customer Service can provide recommendations
of service centers in your area. A listing of authorized service centers is also available at www.marvelrefrigeration.
com under the service and support section.
• In all correspondence regarding service, be sure to
give the model number, serial number, and proof of
purchase.
• Try to have information or description of nature of the
problem, how long the unit has been running, the
room temperature, and any additional information
that may be helpful in quickly solving the problem.
• Fill in pertinent information below regarding your
product for future reference.
For You Records
Date of Purchase
Dealer’s name
Dealer’s Address
Dealer’s City
Dealer’s State
Dealer’s Zip Code
Appliance Serial Number
Appliance Model Number
Date Warranty Card Sent (Must
be within 10 days of purchase).
Electrocution Hazard - Never attempt to repair or perform maintenance on the unit until the main electrical power has
been disconnected.
Problem
Possible Cause
Remedy
Unit not cold enough
• Control set too warm
Adjust temperatures (See “Set the Controls” on page 13)
• Airflow to front grille blocked.
• Excessive usage or prolonged
drawer openings.
• Drawer gasket not sealing properly.
Unit too cold
• Adjust temperature colder. Allow 24 hours for temperature to
stabilize.
• Airflow must not be obstucted to
front grille. See “clearances” on
page 3.
• Allow temperature to stabilize for
at least 24 hours.
• Adjust or replace drawer gasket.
• Control set too cold
• Adjust temperature warmer. (See
page 12, “set the desired temperature”). Allow 24 hours for temperature to stabilize.
No interior light in drawer compartments.
• Failed LED interior light assembly
• Contact a qualified Marvel service
technician.
Light will not go out when drawer is
closed
• Drawer not activating light switch.
• Unit not level, level unit, (See page
3, “leveling legs”)
Noise or Vibration
• Unit not level
• Level unit, see “Leveling Legs” on
page 3.
Unit will not run.
• Unit turned off
• Turn unit on. See “Start your Appliance” on page 13.
• Plug in power cord.
• Check house circuit.
Adjust temperatures (See “Set the Controls” on page 13)
• Power cord not plugged in.
• No power at outlet.
17
HOUSEHOLD PRODUCT WARRANTY
Entire Product
Limited One Year Parts and Labor Warranty
Marvel warrants that it will supply all necessary parts and
labor to repair or replace in the end user’s home or office,
any component which proves to be defective in material
or workmanship, subject to the condition and exclusions
stated below, for a period of one year from the date of
purchase by the end user.
Additional Second Through Fifth Year
Limited Parts Only Warrranty
During the four years following expiration of the one year
limited warranty, Marvel will supply replacement parts for
the hermetically sealed refrigeration system which consists
of the compressor, condenser, drier, accumulator, bypass
valve, connecting tubing and the evaporator that are
proven to be defective due to workmanship or materials
subject to the conditions and exclusions below.
The above warranties do not cover:
• Shipping costs of replacement parts or returned defective parts.
• Customer education or instructions on how to use the
appliance.
• Any content loss due to product failure.
• Removal or installation of product.
Nor do the above warranties cover failure of this product or
its components due to:
• Transportation or subsequent damages.
• Commercial use or use other than normal household
or small office.
• Improper installation, misuse, abuse, accident or
alteration, use of wiring not conforming to electrical
codes, low or high voltages, failure to provide necessary maintenance, or other unreasonable use.
Parts or Service
Not Supplied or Designated by Marvel
The above warranties also do not apply if:
• The original bill of sale, deliver date, or serial number
cannot be verified.
• Defective parts are not returned for inspection if so
requested by Marvel.
• The refrigeration equipment is not in the possession of
the original end use purchaser.
The warranties set forth herein are the only warranties
extended by Northland-Marvel. Any implied warranties, including the implied warranty of merchantability, are limited
to the duration of these express warranties. In no event
shall Northland-Marvel be liable for any consequential or
incidental damages or expenses resulting from breach of
these or any other warranties, whether express or implied.
Some states do not allow the exclusion or limitation of consequential damages or a limitation on how long an implied
warranty lasts, so the above exclusion or limitation may not
apply to you. This warranty gives you specific legal rights
and you may have other rights that may vary from state to
state.
No person, firm, or corporation is authorized to make any
other warranty or assume any other obligation for Northland-Marvel. These warranties apply only to products used
in any of the fifty states of the United States and the District
of Columbia.
To obtain performance of this warranty, report any defects
to:
Northland-Marvel
P.O. Box 400
1260 E. Van Deinse St.
Greenville MI 48838
Phone: 800.223.3900
18
www.marvelrefrigeration.com
Northland-Marvel
P.O. Box 400
1260 E. Van Deinse St.
Greenville MI 48838
800.223.3900
41011754-EN Rev H
11/10/09
All specifications and product designs subject to change without notice. Such revisions do not entitle
the buyer to corresponding changes, improvements, additions, replacements or compensation for
previously purchased products.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement