Dell 800F Computer Monitor User Manual

E828fiW.book Page 1 Thursday, July 2, 1998 7:51 PM
®
Dell® 800F Series, 828FI Color Monitor User’s Guide
www.dell.com
E828fiW.book Page 2 Thursday, July 2, 1998 7:51 PM
Warnings, Cautions, and Notes
Throughout this document, there may be blocks of text printed in bold type or in italic type. These blocks are warnings,
cautions, and notes, and they are used as follows:
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how
to avoid the problem.
NOTE: A NOTE indicates important information that helps you make better use of your computer system.
____________________
Information in this document is subject to change without notice.
© 1994–1998 Dell Computer Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are registered trademarks of Dell Computer Corporation; Microsoft, Windows,
and Windows NT are registered trademarks of Microsoft Corporation; VESA is a registered trademark of Video Electronics Standards
Association; IBM is a registered trademark of International Business Machines Corporation; The ENERGY STAR name and logo are
registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR Partner, Dell Computer Corporation
has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their
products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own.
July 1998
P/N: 22793, 22794, 22795, 22878
E828fiW.book Page iii Thursday, July 2, 1998 7:51 PM
Safety Instructions
Please read and follow these instructions when connecting and using your computer
monitor:
•
To help avoid damaging your computer, be sure the voltage selection switch on the
power supply is set to match the alternating current (AC) power available at your
location:
—
115 volts (V)/60 hertz (Hz) in most of North and South America and some Far
Eastern countries such as Japan, South Korea, and Taiwan
—
230 V/50 Hz in most of Europe, the Middle East, and the Far East
Also be sure your monitor is electrically rated to operate with the AC power available in
your location.
•
Never insert anything metallic into the monitor openings. Doing so may create the
danger of electric shock.
•
To avoid electric shock, never touch the inside of the monitor. Only a qualified technician should open the monitor’s case.
•
Never use your monitor if the power cord has been damaged. Do not allow anything to
rest on the power cord, and keep the cord away from where people could trip over it.
•
Be sure to hold the plug, not the cord, when disconnecting the monitor from an electric socket.
•
Openings in the monitor cabinet are provided for ventilation. To prevent overheating,
these openings should not be blocked or covered. Also, avoid using the monitor on a
bed, sofa, rug, or other soft surface. Doing so may block the ventilation openings in the
bottom of the cabinet. If you put the monitor in a bookcase or some other enclosed
space, be sure to provide adequate ventilation.
•
Put your monitor in a location with low humidity and a minimum of dust. Avoid places
like damp basements or dusty hallways.
•
Do not expose the monitor to rain or use it near water (in kitchens, next to swimming
pools, etc.). If the monitor accidentally gets wet, unplug it and contact an authorized
dealer immediately. You can clean the monitor with a damp cloth when necessary, but
be sure to unplug the monitor first.
•
Place the monitor on a solid surface and treat it carefully. The screen is made of glass
and can be damaged if dropped or sharply hit.
•
•
Locate your monitor near an easily accessible AC outlet.
If your monitor does not operate normally – in particular, if there are any unusual
sounds or smells coming from it – unplug it immediately and contact an authorized
dealer or service center.
Dell® 800F Series, 828FI Monitor User’s Guide
1-iii
E828fiW.book Page iv Thursday, July 2, 1998 7:51 PM
•
High temperatures can cause problems. Don’t use your monitor in direct sunlight, and
keep it away from heaters, stoves, fireplaces, and other sources of heat.
•
•
Unplug the monitor when it is going to be left unused for an extended period of time.
Unplug your monitor from the AC outlet before any service.
Polish Center for Testing and Certification
Notice
The equipment should draw power from a socket with an attached protection circuit (a
three-prong socket). All equipment that works together (computer, monitor, printer, and so
on) should have the same power supply source.
The phasing conductor of the room’s electrical installation should have a reserve shortcircuit protection device in the form of a fuse with a nominal value no larger than 16
amperes (A).
To completely switch off the equipment, the power supply cable must be removed from
the power supply socket, which should be located near the equipment and easily
accessible.
A protection mark “B” confirms that the equipment is in compliance with the protection
usage requirements of standards PN-93/T-42107 and PN-89/E-06251.
1-iv
Dell® 800F Series, 828FI Monitor User’s Guide
E828fiW.book Page v Thursday, July 2, 1998 7:51 PM
Contents
Overview of Your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Connecting Your Monitor to a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Plug and Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Maintenance of Your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4
Monitor Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4
Adjusting Your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5
Automatic Save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5
Direct-Access Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6
Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6
Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6
Menu System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6
On-Screen Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6
Accessing the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6
PowerSaver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-9
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-10
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-13
Display Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-13
Preset Timing Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-13
Regulatory Notices and Warranties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-14
Electric and Magnetic Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-14
Energy Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-14
Federal Communications Commission (FCC) Notice (U.S. Only) . . . . . . . . . . . . . . .1-14
Class B Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-14
Declaration of Conformity for Products Marked With FCC Logo . . . . . . . . . . . . . . .1-15
Canadian Regulatory Information (Canada Only) . . . . . . . . . . . . . . . . . . . . . . . . . . .1-15
CE Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-15
Dell® 800F Series, 828FI Monitor User’s Guide
1-v
E828fiW.book Page vi Thursday, July 2, 1998 7:51 PM
EN 55022 Compliance (Czech Republic Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-16
VCCI Class 2 Notice (Japan Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-16
Warranties and Return Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-16
Limited One-Year Warranty (U.S. Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-16
“Total Satisfaction” Return Policy (U.S. and Canada) . . . . . . . . . . . . . . . . . . . . . . .1-17
One Year Dell Manufacturer End-User Guarantee European Union, Norway
and Switzerland . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-18
Dell Computer Corporation’s Environmental Program . . . . . . . . . . . . . . . . . . . . . . . . . .1-18
Design for Longevity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-19
Design for Recyclability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-20
Design for Reduced Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-20
Dell’s Blue Angel Disposal Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-20
Dell’s Green Away Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-21
How the Green Away Program Works. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-21
Regulatory Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-22
Spare Parts Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-22
Green Away Collection Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-23
Tables
Table 1-1.
Table 1-2.
Table 1-3.
Table 1-4.
Table 1-5.
1-vi
Menu Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-7
Power-Saving Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-10
Troubleshooting Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-10
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12
Green Away Collection Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-23
Dell® 800F Series, 828FI Monitor User’s Guide
E828fiW.book Page 1 Thursday, July 2, 1998 7:51 PM
Dell® 800F Series, 828FI Monitor
User’s Guide
Overview of Your Monitor
–
+
MENU
EXIT
①
② ③ ④ ⑤⑥ ⑦
Front Panel
1.
MENU / EXIT
Use this button to open the on-screen display (OSD) or to exit out of an on-screen
display.
2.
–/+
Use these buttons to adjust items in the on-screen display.
3.
Brightness
Use this button to access the brightness controls.
4.
Contrast
Use this button to access the contrast controls.
5.
Use this button to choose an item in the on-screen display.
Dell® 800F Series, 828FI Monitor User’s Guide
1-1
E828fiW.book Page 2 Thursday, July 2, 1998 7:51 PM
6.
Power indicator
This light glows green during normal operation.
7.
Power button
Use this button to turn the monitor on and off.
①
②
Back Panel
1-2
1.
Power port
Connect the power cable here.
2.
Signal cable
Connect this cable to the video connector on your computer.
Dell® 800F Series, 828FI Monitor User’s Guide
E828fiW.book Page 3 Thursday, July 2, 1998 7:51 PM
Installation
Connecting Your Monitor to a Computer
②
③
④
1.
Turn off your computer and unplug its power cord.
2.
Connect the blue signal cable to the blue video port on the back of your
computer.
3.
Connect the power cord for your monitor to the power port on the back of
the monitor.
4.
Plug the power cords of your computer and your monitor into a nearby
outlet.
5.
Turn on your computer and monitor. If your monitor displays an image,
installation is complete.
Plug and Play
Our adoption of the new VESA® plug and Play solution eliminates complicated and time
consuming setup. It allows you to install your monitor in a Plug and Play compatible system
without the usual hassles and confusion. Your PC system can easily identify and configure
itself for use with your monitor. This monitor automatically tells the PC system its
Extended Display Identification (EDID) data using Display Data Channel (DDC) protocols so
the PC system can automatically configure itself and optimize the monitor settings. If
desired, the user can select different settings, but in most cases, monitor installation is
automatic.
Dell® 800F Series, 828FI Monitor User’s Guide
1-3
E828fiW.book Page 4 Thursday, July 2, 1998 7:51 PM
Maintenance of Your Monitor
WARNING: To avoid risk of electric shock, do not disassemble the monitor cabinet. The unit is not user-serviceable. User maintenance is restricted to cleaning
as explained below:
Unplug the monitor from the power outlet before cleaning.
•
To clean your antistatic screen, lightly dampen a soft, clean cloth with water or mild
detergent. If possible, use a special screen cleaning tissue or solution suitable for the
antistatic coating.
•
•
To clean the monitor cabinet, use a cloth lightly dampened with a mild detergent.
Wipe off stubborn stains from the cabinet or screen with a cloth lightly dampened in
alcohol (methyl, ethyl or isopropyl). Do not use benzine, thinner, ammonia, abrasive
cleaners, or compressed air.
Monitor Self Test
Your monitor provides a self test feature which allows you to check if your monitor is functioning properly. If your monitor and computer are properly connected but the monitor
screen remains dark and the power indicator is blinking, use the following steps to perform
the monitor self test:
1.
Turn off both your computer and the monitor.
2.
Unplug the video cable from the computer or video card.
3.
Turn on the monitor.
If the monitor is functioning properly, you will see a white box with a red border and
black text inside stating:
This box will also appear during normal operation of your system if the video cable
becomes disconnected or damaged.
4.
Turn off your monitor and reconnect the video cable; then turn on both your
computer and monitor.
If your monitor screen remains blank after using the above procedure, check your video
controller and computer system; your monitor is functioning properly.
1-4
Dell® 800F Series, 828FI Monitor User’s Guide
E828fiW.book Page 5 Thursday, July 2, 1998 7:51 PM
Adjusting Your Monitor
Your computer monitor allows you to easily adjust the characteristics of the image being
displayed. All of these adjustments are made using the control buttons on the front of the
monitor. While you use these buttons to adjust the controls, an on-screen menu shows
you their numeric values as they change.
–
+
MENU
EXIT
①
②
③
1.
The MENU / EXIT button opens and closes the on-screen menu.
2.
The −/+ buttons allow you to select and adjust items in the menu. When the
menu is not displayed, these buttons directly adjust the brightness and
contrast.
3.
The
button activates the function highlighted on the on-screen menu.
WARNING: Holding in this button for longer than 5 seconds erases all data in
the User Settings memory.
Automatic Save
Whenever you open the on-screen menu and allow an adjustment window to remain
on-screen for about three seconds without pressing another button, this monitor automatically saves any adjustments you have made. These changes are saved into a user area in
the monitor. User areas are reserved according to the signal frequency from your computer. This monitor can save adjustments for up to eight user modes. It has eight factory
preset or preload modes, one for each signal frequency as listed in the “Preset Timing
Modes” on page 13.
If you have made no adjustments the on-screen menu disappears and the monitor does
not save anything.
To exit without saving the changes you have made, press the MENU / EXIT button before
the three seconds elapse.
Dell® 800F Series, 828FI Monitor User’s Guide
1-5
E828fiW.book Page 6 Thursday, July 2, 1998 7:51 PM
Direct-Access Features
The features described on this page can be accessed quickly, at the touch of one button.
Once you are finished making adjustments to a feature, push the MENU / EXIT button to
return to the Menu, then push MENU / EXIT again to turn off the menu.
Brightness
BRIGHTNESS
100
–
+
Follow these instructions to adjust the brightness of the monitor’s display.
1. With the menu off, push the “−
−” button. The brightness display will appear.
2.
Push the “+” button to increase the brightness;
push the “−
−” button to decrease the brightness.
Contrast
CONTRAST
100
–
+
Follow these instructions to adjust the contrast between darkness and lightness on the monitor’s display.
1. With the menu off, push the “+” button. The contrast display will appear.
2.
Push the “+” button to increase the contrast; push
the “−
−” button to decrease the contrast.
Menu System
On-Screen Menu
Title bar
MENU
Features
icons
Features
name
?
L
H. POSITION
Accessing the Menu System
1.
1-6
With the menu off, push the MENU/EXIT button to open the menu system
and display the main features menu.
Dell® 800F Series, 828FI Monitor User’s Guide
E828fiW.book Page 7 Thursday, July 2, 1998 7:51 PM
2.
Push the + button to move to the next icon or push the − button to move
back to the previous icon. As you move from one icon to another, the feature name changes to reflect the feature or group of features represented
by that icon. See the table below to view a complete list of all the features
offered by this monitor.
3.
Push the
button once to select the adjustment function, then use the +
and − buttons to make your changes.
4.
Push the MENU/EXIT button once to return to the main menu to select
another function or push MENU/EXIT button 2 or 3 times to exit from the
OSD.
Table 1-1. Menu Adjustments
Icon
Settings
Brightness: Selecting this icon opens the
same brightness display screen as when
using the direct access button (−
−).
Contrast: Selecting this icon opens the
same contrast display screen as when using
the direct access button (+).
H. POSITION
52
–
+
V. POSITION
52
–
+
Vertical position: Select this icon to vertically
move the viewing area on the monitor
screen.
52
Width: Select this icon to make the horizontal size of the viewing area larger or smaller
on the monitor.
52
Height: Select this icon to make the vertical
size of the viewing area larger or smaller on
the monitor.
WIDTH
–
Horizontal position: Select this icon to horizontally move the viewing area on the monitor screen.
+
HEIGHT
–
+
COLOR
9300K
6500K
Color is a measure of the “warmth” of the
image colors. Select this icon to choose
between 9300K (more blue) and 6500K
(more red).
Dell® 800F Series, 828FI Monitor User’s Guide
1-7
E828fiW.book Page 8 Thursday, July 2, 1998 7:51 PM
Table 1-1. Menu Adjustments (continued)
Icon
Settings
Degauss: Select this icon if you notice a
problem with inconsistent colors. This feature removes unwanted magnetic fields that
may build up on your monitor and distort the
colors. Do not use this feature more than
once within a 30-minute period.
DEGAUSS
YES
NO
Note: The monitor may buzz momentarily,
the image colors may change and the image
will jiggle for a few seconds. These effects
are normal.
Recall: Select this icon to reset the horizontal and vertical position and size and the
geometric distortion features to their original settings.
RECALL
YES
NO
USER
56.4KHz
.
.
.
.
.
.
.
56.4KHz
?
MODE
70Hz N N
70Hz N N
Advanced: Select this icon to access a
group of features that affect the shape of
the viewing area (geometric distortion, G/D).
Select the icon for the feature you want to
adjust and push
button again.
ADVANCED
PINCUSHION
Pincushion: Select this icon when the sides
of the viewing area are bowed in or bowed
out.
PINCUSHION
52
–
+
52
Trapezoid: Select this icon when the viewing
area is too large or too small.
52
Parallelogram: Select this icon when the
viewing area is leaning left or right.
TRAPEZOID
–
+
PARALLELOGRAM
–
1-8
Information: Select this icon to view the current user mode and any other user modes
that are available. This screen only displays
information; you cannot select a new
setting.
+
Dell® 800F Series, 828FI Monitor User’s Guide
E828fiW.book Page 9 Thursday, July 2, 1998 7:51 PM
Table 1-1. Menu Adjustments (continued)
Icon
Settings
Pinbalance: Select this icon when the sides
of the viewing area are bowed towards the
left or right.
PIN-BALANCE
52
–
+
Vertical linearity: Select this icon when the
contents of the viewing area look “compressed” at the top or the bottom of the
screen.
V-LINEARITY
52
–
+
Rotation: Select this icon when the entire
viewing area is tilted left or right.
ROTATION
52
–
+
Vertical moire: A “moiré” pattern can
appear on your screen, looking like a series
of concentric circles or arcs. Select this icon
to set the moiré correction feature “on” (+)
or “off” (−
−).
V-MOIRE
52
–
+
LANGUAGE
ENGLISH
DEUTSCH
ESPAÑOL
FRANÇAIS
I TA L I A N O
L
Language: Changes to display the OSD data
in any of the five languages listed. Use the −
or + button to select between English,
Deutsch, Español, Français, and Italiano.
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system
saves energy by switching your monitor into a low-power mode when it has not been used
for a certain amount of time. The available modes are “On”, “Standby”, “Suspend”, and “Off”.
This system operates with a VESA DPMS compliant video card installed in your computer.
You use a software utility installed on your computer to set up this feature. See Table 1-2
below for details.
Dell® 800F Series, 828FI Monitor User’s Guide
1-9
E828fiW.book Page 10 Thursday, July 2, 1998 7:51 PM
Table 1-2. Power-Saving Modes
Power-Saving Function mode (EPA/NUTEK)
State
Normal
Operation
Standby
mode
Suspend
mode
Position A1
Power-off
Mode
Position A2
Horizontal Sync
Vertical Sync
Video
Active
Active
Active
Inactive
Active
Blanked
Active
Inactive
Blanked
Inactive
Inactive
Blanked
Power
Indicator
Green
Green
Blinking
(0.5 sec
interval)
Green
Blinking
(1 sec interval)
Green
Blinking
(2 sec interval)
85W (max.)
75W (nominal)
55W
(nominal)
Less than 15W
Less than 8W
Power
Consumption
NOTE: This monitor automatically returns to normal operation when horizontal and vertical
sync return. This occurs when you move the computer’s mouse or press a key on the
keyboard.
This monitor is EPA ENERGY STAR compliant and NUTEK compliant when used with a computer equipped with VESA DPMS functionality.
For energy conservation, turn your monitor OFF when it is not needed, or when leaving it
unattended for long periods.
Troubleshooting
Before calling for service, check the information in this section to see if you can remedy
any problems yourself.
Table 1-3. Troubleshooting Problems
Symptom
Corrective Actions
No Picture
•
Check to see that both the monitor and the computer
are plugged in and turned on.
“NO CONNECTION!
Check Signal Cable”
appears
•
Check the signal cable connection between the
computer and the monitor
•
•
Use the monitor self test described on page 5.
Picture bounces or has
wavy oscillations.
•
Check the signal cable connection between the
computer and monitor
Picture appears to be
ghosting
•
Check the signal cable connection between the
computer and monitor.
Picture is scrambled
1-10
Check the signal cable connection between the
computer and monitor
Dell® 800F Series, 828FI Monitor User’s Guide
E828fiW.book Page 11 Thursday, July 2, 1998 7:51 PM
Table 1-3. Troubleshooting Problems (continued)
Symptom
Corrective Actions
Color is not uniform
•
Activate the Degauss feature using the OSD DEGAUSS
menu
•
Adjust the color settings using the OSD COLOR menu.
•
Activate the Degauss feature using the OSD DEGAUSS
menu.
•
Adjust the color settings using the OSD COLOR menu.
•
Activate the Degauss feature using the OSD DEGAUSS
menu
•
•
Adjust the color settings using the OSD COLOR menu.
Edges of the image are
curved
•
Adjust the shape of the display using the OSD
ADVANCED menu.
Wavy or elliptical (moiré)
pattern is visible
•
Clear the moiré pattern using the OSD V-MOIRE menu
The power indicator is
blinking green
•
lThe monitor is using its power management system.
Check the power management utility on your
computer.
The image is too light or
too dark
•
Adjust the Brightness and Contrast settings using the
OSD menu.
Cannot adjust monitor
with the buttons on the
front panel
•
Please contact Dell customer service.
White lines show red or
blue shades at the edges
•
•
Check surroundings for magnetic fields.
Picture is fuzzy
•
•
Perform monitor reset.
White does not look
white
The colors are distorted
with dark or shadowed
areas
Screen image is not centered or sized properly
Adjust the Horizontal and Vertical position settings And
/ or the Height and Width settings using the OSD.
Perform monitor reset.
Eliminate accessories (i.e., Video extension cables).
Dell® 800F Series, 828FI Monitor User’s Guide
1-11
E828fiW.book Page 12 Thursday, July 2, 1998 7:51 PM
Specifications
Table 1-4. Specifications
Picture Tube . . . . . . . . . . . . . . . . . . . . . . . 38 cm (15") full square type [35 cm (13.8")
viewable]
Flat face 90× deflection
0.28 Dot pitch
Anti-reflection coating with Anti-electrostatic
Medium short persistence phosphor
Synchronization . . . . . . . . . . . . . . . . . . . . Horizontal:
Vertical:
30 kHz to 70 kHz (automatic)
50 Hz to 120 Hz (automatic)
Maximum Resolution . . . . . . . . . . . . . . . Horizontal:
Vertical:
1280 dots @ 64 kHz
1024 lines @ 60 Hz
Active Display . . . . . . . . . . . . . . . . . . . . . Horizontal: 267 ± 3 mm (10.5" ± 0.12")
Vertical:
200 ± 3 mm (7.87" ± 0.12")
(Active display size is dependent upon signal
timing)
Input Signal, Terminated . . . . . . . . . . . . . Analog video 0.714 Vpp positive at 75 Ω
Separate sync: TTL level, positive or negative
Maximum Pixel Clock . . . . . . . . . . . . . . . 110 MHz
Power Supply. . . . . . . . . . . . . . . . . . . . . . AC 100-240 Volt ± 10%, 60 Hz/50 Hz ± 3 Hz
Power Consumption . . . . . . . . . . . . . . . . 85 W (maximum), 75 W (nominal)
BTUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heat Release per Hour : 255.91 BTU/Hr
Dimensions/Weight . . . . . . . . . . . . . . . . . Unit:
370 x 395 x 377 mm; 12.5 kg
14.6 x 15.6 x14.8 in (W x D x H);
27.6 lb
Carton: 454 x 497 x 433 mm; 14.3 kg
17.9 x 19.6 x 17.0 in (W x D x H);
31.5 lb
(All measurements approximate.)
Environmental Considerations. . . . . . . . . Operating Temperature: 32°F to 104°F
(0°C to 40°C)
Humidity: 10% to 80%
Storage Temperature: -4°F to 149°F
(-20°C to 65°C)
Humidity: 5% to 95%
NOTE: Design and specifications are subject to change without prior notice.
1-12
Dell® 800F Series, 828FI Monitor User’s Guide
E828fiW.book Page 13 Thursday, July 2, 1998 7:51 PM
Pin Assignments
Sync Type:
Separate
15-Pin Side of the Signal Cable
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Red
Green
Blue
GND
DDC Return
GND-R
GND-G
GND-B
Reserved
GND-Sync/Self-Raster
GND
DDC Data
H-Sync
V-Sync
DDC Clock
Display Resolution
For optimal monitor performance while using Microsoft Windows 95 or Windows NT®,
set the display resolution to 800 x 600 as follows :
1.
Click the Start button, point to Settings, and click Control Panel.
2.
Double-click the Display icon in the Control Panel window, and then click the
Settings tab.
3.
In the Desktop area, move the slidebar to 800 by 600 pixels, then click OK.
Preset Timing Modes
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM®, VGA2, 720 x 400
IBM®, VGA3, 640 x 480
VESA®, 640 x 480
VESA®, 640 x 480
VESA®, 800 x 600
VESA®, 800 x 600
VESA®, 1024 x 768
VESA®, 1024 x 768
31.469 ®
31.469 ®
37.500 ®
43.269 ®
46.875 ®
53.674 ®
60.023 ®
68.677 ®
70.087 ®
59.940 ®
75.000 ®
85.008 ®
75.000 ®
85.061 ®
75.029 ®
84.997 ®
28.322 ®
25.175 ®
31.500 ®
36.000 ®
49.500 ®
56.250 ®
78.750 ®
94.500 ®
-/+ ®
-/- ®
-/- ®
-/- ®
+/+ ®
+/+ ®
+/+ ®
+/+ ®
Dell® 800F Series, 828FI Monitor User’s Guide
1-13
E828fiW.book Page 14 Thursday, July 2, 1998 7:51 PM
Regulatory Notices and Warranties
Electric and Magnetic Fields
Energy Efficiency
The proper operation of the function requires a computer with VESA DPMS
power management capabilities. When used with a computer equipped
with VESA DPMS, the monitor is ENERGY STAR
compliant.
Federal Communications Commission (FCC) Notice
(U.S. Only)
Class B Notice
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer's instruction manual, may cause
harmful interference with radio and television reception. This equipment has been tested
and found to comply with the limits for a Class B digital device pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of these
measures:
•
•
•
•
Reorient or relocate receiving antenna.
Relocate the equipment with respect to the receiver.
Move the equipment away from the receiver.
Plug the equipment into a different outlet so that the equipment and receiver are on
different branch circuits.
If necessary, consult a representative of Dell Computer Corporation or an experienced
radio/television technician for additional suggestions. You may find the following booklet
helpful: FCC Interference Handbook, 1986, available from the U.S. Government Printing
Office, Washington, DC 20402, Stock No. 004-000-00450-7.
Note that FCC regulations provide that changes or modifications not expressly approved by
Dell Computer Corporation could void your authority to operate this equipment.
A Notice About Shielded Cables: Use only shielded cables for connecting peripherals to
any Dell device to reduce the possibility of interference with radio and television reception.
Using shielded cables ensures that you maintain FCC Class B certification of this product.
For parallel printers, a cable is available from Dell Computer Corporation.
1-14
Dell® 800F Series, 828FI Monitor User’s Guide
E828fiW.book Page 15 Thursday, July 2, 1998 7:51 PM
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
•
•
This device may not cause harmful interference.
This device must accept any interference received, including interference that may
cause undesired operation.
Declaration of Conformity for Products Marked With FCC
Logo
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD
QA Lab of Samsung America
85 West Tasman Drive
San Jose, CA 95134 USA
(Tel) 408-544-5124
(Fax) 408-544-5191
Canadian Regulatory Information (Canada Only)
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department
of Communications.
Note that Canadian Department of Communications (DOC) regulations provide, that
changes or modifications not expressly approved by Dell Computer Corporation could void
your authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Rglement sur le
matériel brouilleur du Canada.
CE Notice
Products with the CE marking comply with both the EMC Directive (89/336/EEC), (92/31/
EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of
the European Community.
Compliance with these directives implies conformity to the following European Norms:
•
EN55022 (CISPR 22) - Radio Frequency Interference
Dell® 800F Series, 828FI Monitor User’s Guide
1-15
E828fiW.book Page 16 Thursday, July 2, 1998 7:51 PM
•
•
•
•
EN50082-1 : 1992 - Electromagnetic Immunity
EN60555-2 (IEC555-2) - Power Line Harmonics
EN60555-3 (IEC555-3) - Voltage Fluctuations
EN60950 (IEC950) - Product Safety
EN 55022 Compliance (Czech Republic Only)
This device belongs to category B devices as described in EN 55022, unless it is specifically stated that it is a category A device on the specification label. The following applies to
devices in category A of EN 55022 (radius of protection up to 30 meters). The user of the
device is obliged to take all steps necessary to remove sources of interference of telecommunication or other devices.
!!"#$%&' (()**"
$% +&'(()**,-.&..&.%&/+0-
%$1)2'(()**'%$'3+,435' -' !+06
3 +0.&."3# ' -$%&"6-$- ',
VCCI Class 2 Notice (Japan Only)
This equipment complies with the limits for a Class 2 digital device (devices used in or adjacent to a residential environment) and conforms to the standards for information
technology equipment that are set by the Voluntary Control Council for Interference for preventing radio frequency interference in residential areas.
However, this equipment does generate, use, and can radiate radio frequency energy and,
if not installed and used in accordance with the manufacturer's instruction manual, may
cause interference with radio and television reception. Therefore, it is important to adhere
to the manufacturer's instructions for installing and using this equipment.
Warranties and Return Policy
Limited One-Year Warranty (U.S. Only)
Dell Computer Corporation (“Dell”) manufactures its hardware products from parts and
components that are new or equivalent to new in accordance with industry-standard practices. Dell warrants that the hardware products it sells will be free from defects in
materials and workmanship. The warranty term is one year beginning on the date of
delivery.
Damage due to shipping the products to you is covered under this warranty. Otherwise,
this warranty does not cover damage due to external causes, including accident, abuse,
misuse, problems with electrical power, servicing not authorized by Dell, usage not in
accordance with product instructions, and failure to perform required preventive
maintenance.
Dell will repair or replace products returned to Dell's facility. To request warranty service,
you must call Dell customer service within the warranty period. If warranty service is
1-16
Dell® 800F Series, 828FI Monitor User’s Guide
E828fiW.book Page 17 Thursday, July 2, 1998 7:51 PM
required, Dell will issue a Return Material Authorization Number. You must ship the products back to Dell in their original packaging or equivalent, prepay shipping charges, and you
must insure the shipment or accept the risk of loss or damage during shipment. Dell will
ship the repaired or replacement products to you freight prepaid if you use an address in
the United States (excluding Puerto Rico and U.S. possessions). Shipments to other locations will be made freight collect.
Dell owns all parts removed from repaired products. Dell uses new and reconditioned parts
made by various manufacturers in performing warranty repairs and building replacement
products. If Dell repairs a product, its warranty term is not extended; if Dell replaces a
product, the replacement is warranted for the remainder of the original term or 60 days,
whichever is longer.
Dell MAKES NO EXPRESS WARRANTIES BEYOND THOSE STATED HERE. DELL DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SOME STATES DO NOT ALLOW LIMITATIONS ON IMPLIED
WARRANTIES, SO THIS LIMITATION MAY NOT APPLY TO YOU.
Dell’s RESPONSIBILITY FOR MALFUNCTIONS AND DEFECTS IN HARDWARE IS LIMITED TO REPAIR AND REPLACEMENT AS SET FORTH ABOVE. THESE WARRANTIES
GIVE YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH
VARY FROM STATE TO STATE.
Dell DOES NOT ACCEPT LIABILITY BEYOND THE REMEDIES SET FORTH IN THIS WARRANTY STATEMENT OR LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES,
INCLUDING WITHOUT LIMITATION ANY LIABILITY FOR PRODUCTS NOT BEING AVAILABLE FOR USE OR FOR LOST DATA OR SOFTWARE.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT
APPLY TO YOU.
These provisions apply to Dell's return-to-factory warranty only. For provisions of any onsite service contract covering your system, refer to the separate on-site service contract
that you will receive.
“Total Satisfaction” Return Policy (U.S. and Canada)
If you bought products directly from a Dell company, you may return them to Dell up to
30 days from the day they are delivered for a complete refund of the purchase price. If your
company bought the products under a Corporate Performance Agreement with a Dell company, there are limits on when products may be returned to Dell under this policy. Please
consult the person in your company that is the liaison with Dell for more information. To
return products, you must call Dell customer service to receive a Credit Return Authorization Number. You must ship the products to Dell in their original packaging, prepay shipping
charges, and insure the shipment or accept the risk of loss or damage during shipment.
Returned products must be in as-new condition, and all of the manuals, diskettes, power
cables, and other items included with a product must be returned with it.
Dell® 800F Series, 828FI Monitor User’s Guide
1-17
E828fiW.book Page 18 Thursday, July 2, 1998 7:51 PM
One Year Dell Manufacturer End-User Guarantee European
Union, Norway and Switzerland
Guarantee
DELL Products, Raheen Industrial Estate, Limerick, Ireland (DELL) warrants to the end-user
in accordance with the following provisions that its branded hardware products, purchased
by the end-user from a DELL company or an authorized DELL distributor, in the European
Union, Norway or Switzerland, will be free from defects in materials, workmanship and
design affecting normal use, for a period of one year as of the original purchase date. Products for which proper claims are made will, at DELL’s option, be repaired or replaced at
DELL’s expense.
Exclusions
This Guarantee does not apply to defects resulting from: improper or inadequate installation, use or maintenance; actions or modifications by unauthorized third parties or the enduser; accidental or wilful damage or normal wear and tear.
Making a claim
Claims must be made in the European Union, Norway or Switzerland, by contacting the
point of sale or any DELL office within the guarantee period. The end-user must always
supply proof of purchase, indicating name and address of the seller, date of purchase,
model and serial number, name and address of the customer and details of symptoms and
configuration at time of malfunction, including peripherals and software used. Otherwise,
DELL may refuse the guarantee claim. Upon diagnosis of a warranted defect, DELL will
make arrangements, and pay for ground freight and insurance to and from DELL repair/
replacement centre. End-user must ensure defective product is available for collection
properly packed in original or equally protective packaging together with details listed
above and the return number provided to the end-user by DELL.
Limitation and Statutory Rights
DELL makes no other warranty, guarantee or like statement other than as explicitly stated
above and this Guarantee is given in place of all other guarantees whatsoever, to the fullest
extent permitted by law. In the absence of applicable legislation, this Guarantee will be the
end-user’s sole and exclusive remedy against DELL or any of its affiliates, and neither DELL
nor any of its affiliates shall be liable for loss of profit or contracts, or any other indirect or
consequential loss arising from negligence, breach of contract, or howsoever.
This Guarantee does not impair or affect mandatory statutory rights of the end-user against
and/or any rights resulting from other contracts concluded by the end-user with DELL and/
or any other seller.
Dell Computer Corporation’s Environmental
Program
Growing concern over protecting the environment has led many organizations to focus on
the potential impact of their product design and manufacturing practices. Environmentally
smart product development requires commitment to a long-term, systematic, continually
improvable program. Dell’s corporate initiative in this area calls for increasing its focus on
1-18
Dell® 800F Series, 828FI Monitor User’s Guide
E828fiW.book Page 19 Thursday, July 2, 1998 7:51 PM
environmental concerns, as well as accommodating the guidelines expected in future environmental legislation in a variety of geographical locations.
Good environmental design affects many aspects of the design and manufacturing process, down to the level of which chemicals, coatings, and additives are allowed. However,
this document addresses the aspects of Dell’s environmental program that should most
interest you as a customer. This document applies to all Dell-branded equipment-primarily
system units, monitors, and keyboards.
First, systems that comply with Dell’s environmental program incorporate the following
features:
•
•
•
A modular, highly upgradable design that extends the useful life of the basic unit
Mechanical design that facilitates recycling and material disposal
A consistent and documented multilevel power consumption scheme that meets the
need to significantly reduce energy consumption
Dell peripherals meet the requirements of Dell’s environmental program by offering the
following features:
•
•
Mechanical design that facilitates speedy disassembly for recycling
Reduced variations in plastics, and plastics marked to internationally recognized standards for correct identification and the appropriate recycling process.
Other areas of interest include the following programs:
•
The Green Away program, which provides for the disposition of obsolete or otherwise
unwanted equipment
•
•
An approved disposal policy for used system batteries
A spare-parts provision in the Dell service agreement
These aspects of Dell’s environmental program are described in detail in the following
sections.
Design for Longevity
Your Dell computer’s modular design allows you to keep the system up-to-date by adding
or upgrading many system components. Instructions for installing the following components are included in your computer system’s user documentation:
•
The system microprocessor, system memory, and storage devices (hard-disk drives,
diskette drives, tape drives, and CD-ROM drives) can be easily replaced or upgraded.
(The microprocessor and the memory can be upgraded without using tools.)
•
Depending on your system’s chassis design and the options installed at initial shipment, a number of expansion slots are available to accommodate additional controller
cards.
•
Also depending on your system, you may be able to upgrade your external cache and/
or video memory.
In addition to many of the components being replaceable by hand (that is, without tools),
the chassis itself snaps together using primarily hooks and latches, with very few screws;
Dell® 800F Series, 828FI Monitor User’s Guide
1-19
E828fiW.book Page 20 Thursday, July 2, 1998 7:51 PM
the computer cover can be removed and replaced by hand. This snap-together capability
both simplifies upgrade procedures and facilitates disposal or reuse of the unit and/or its
components (see “Dell’s Green Away Program” found later in this document).
NOTE: Because monitors and keyboards have a potentially long life and are interchangeable
for many systems, customers do not upgrade or replace these components as often as
they replace their computers. Therefore, disposal of these components it not an issue as
often.
Design for Recyclability
Your Dell equipment complies with the following principles of recyclable design:
•
Avoidance of nonseparable connections, such as gluing and welding, between different materials
•
•
•
Avoidance of coatings and composite structure materials
Use of as few different materials as possible
Designed for ease of disassembly:
—
Subassemblies, cables, and components easily detachable by one person working alone
—
Minimal use of screws
—
Most disassembly can be done by hand or with the aid of a standard 6-millimeter
(1/4-inch) nut driver only
Design for Reduced Power Consumption
Both your system and your monitor are equipped with an energy-saving sleep mode that
can be set to activate automatically after a certain period of system or monitor inactivity. In
sleep mode, the system and monitor use the minimum amount of power that will maintain
operational data and parameters. Refer to “Power Consumption” found later in this document for details of your equipment power consumption.
NOTE: Zero power consumption can be attained only when the system and monitor are
completely disconnected from the alternating current (AC) power source.
Dell’s Blue Angel Disposal Program
Rapid technological advances lead to a high turnover in computer products, as customers
upgrade or replace their systems at an ever-increasing rate. To address the mounting problem regarding the indiscriminate disposal of unwanted products, and in anticipation of
future legislation, Dell has instituted a disposal program, called Green Away, for the collection and disposal of these products.
1-20
Dell® 800F Series, 828FI Monitor User’s Guide
E828fiW.book Page 21 Thursday, July 2, 1998 7:51 PM
Dell’s Green Away Program
Dell’s Green Away program is a free material return and disposal service for Dell customers, covering computer products sold by Dell under the Blue Angel plan. The returned
products are reused, recycled or disposed of as appropriate, in accordance with local environmental guidelines.
NOTE: The Green Away program is designed to dispose of unwanted or unusable products
under the Blue Angel plan.
For returned material discounts on recent purchases, or for recycling of equipment neither
sold by Dell nor covered by the Blue Angel plan, contact your local Dell Asset Management
specialist.
In carrying out this program, Dell’s general responsibilities include the following:
•
•
•
Organizing the reuse/recycling/disposal of the equipment
Ensuring that all disposal/recycling practices meet local environmental regulations
Monitoring the process to ensure compliance and facilitate process improvement
How the Green Away Program Works
When you have one or more items of equipment that you would like to dispose of, contact
your local Dell customer service department to request instructions. The returns coordinator processes the request and advises you on the return of your material. Refer to “Green
Away Collection Points” found later in this document for the telephone number and collection point in your area.
NOTE: “Shells” (equipment from which integral components, such as chips and power
supplies have been removed) are not accepted as part of this free program. If a shell is discovered in your shipment, you will be asked to either collect the system or pay for its
disposal.
Dell® 800F Series, 828FI Monitor User’s Guide
1-21
E828fiW.book Page 22 Thursday, July 2, 1998 7:51 PM
The equipment is transported to Dellºs Green Away partner, where it is assessed and disposed of as follows:
•
If judged resalable, the Dell label is removed and the equipment is tested, repaired,
and resold.
•
If judged beyond repair, the equipment is dismantled, and usable parts are offered for
sale.
Unusable parts are disposed of as follows:
•
•
•
•
Metal cases are sold to metals recyclers.
Printed circuit boards and cases are sent to refiners.
Plastic parts are sent to plastic recyclers.
Unusable packaging is sent to paper recyclers.
Monitors are sent to recycling companies to be disposed as follows:
•
The tubes are washed and the luminescent powder is recovered, some elements are
extracted for reuse, and the remainder is disposed of via controlled incineration.
•
•
•
Glass is sorted and sent to the lead smelter or recylced for glass works.
The planar mask and the iron are sent for reuse to metals recyclers.
Items that are not reusable are mainly incinerated.
However, if certain residues on the items are not allowed in hazardous waste incinerators, the Dell Green Away partner transports items to a secured (bundled) hazardous
waste landfill.
Regulatory Note
No Dell systems use batteries containing heavy metal. However, the following note is
included to comply with German regulatory standards.
NOTE: Heavy-metal-containing batteries and accumulators should not be disposed of
together with the general household waste. To make sure that they are forwarded to recycling or proper disposal, they may be returned free of charge to the manufacturer, dealer, or
their agent.
Spare Parts Policy
Dell commits to retaining stocks of spare parts (or reasonable alternatives) for a period of
five years from the termination of production of the Dell system component-for example,
the base system, the keyboard, or the monitor.
1-22
Dell® 800F Series, 828FI Monitor User’s Guide
E828fiW.book Page 23 Thursday, July 2, 1998 7:51 PM
Green Away Collection Points
Table 1 lists the country specific customer service telephone number along with the Green
Away collection point. For Germany, the Green Away collection point telephone number is
listed rather than the customer service number.
NOTE: Locations marked with an asterisk (*) are approved facilities for battery disposal. As
Dell expands the network of Green Away centers, additional addresses will be available
across Europe. Contact your local Dell customer service department for information about
the availability of Green Away services in your location.
Table 1-5. Green Away Collection Points
Country
Telephone
Address (model)
Belgium
02 481 91 00
R Frazier Ltd.
Plantijnweg 15
4104 BC Culemborg, Netherlands
Denmark
+46-8-5900 5151
WMI Sellbergs AB
Box 1294
S-171 25 Solna, Sweden
Finland
+46-8-5900 5181
WMI Selbergs AB
Box 1294
S-171 25 Solna, Sweden
Northern Germany
0130-86-12 51
*Bockmann/Ohlig
Tersteegenstrasse 21a 42653
Southern Germany
0130-86-12 51
*Knab
Carl Benz Strasse 8-10
35440 Linden
Netherlands
02 481 91 00
R Frazier Europe
Plantijnweg 15
4104 BC Culemborg, Netherlands
Norway
+46-8-5900 5179
WMI Sellbergs AB
Box 1294
S-171 25 Solna, Sweden
Sweden
+46-8-5900 5169
WMI Sellbergs AB
Box 1294
S-171 25 Solna, Sweden
United Kingdom
*R Frazier Ltd.
Irongray Business Park
Lochside Industrial Estate
Dumfries
DG2 0NR
Dell® 800F Series, 828FI Monitor User’s Guide
1-23
E828fiW.book Page 24 Thursday, July 2, 1998 7:51 PM
1-24
Dell® 800F Series, 828FI Monitor User’s Guide
E828fiW.book Page 1 Thursday, July 2, 1998 7:51 PM
Index
Symbols
G
– / +, 1-1
Green Away Collection Points, 1-23
A
H
Automatic Save, 1-5
Height, 1-7
Horizontal position, 1-7
B
Brightness, 1-1, 1-6, 1-7
I
incushion, 1-8
C
Color, 1-7
Information, 1-8
Connecting, 1-3
M
Contrast, 1-1, 1-6, 1-7
Maintenance, 1-4
MENU / EXIT, 1-1
D
Dell Computer Corporation’s
Environmental Program, 1-18
Direct-Access Features, 1-6
Monitor Self Test, 1-4
N
Display Resolution, 1-13
NO CONNECTION! Check Signal Cable,
1-4, 1-10
F
P
Front Panel, 1-1
Parallelogram, 1-8
Plug and Play, 1-3
Power button, 1-2
Dell® 800F Series, 828FI Monitor User’s Guide
Index-1
E828fiW.book Page 2 Thursday, July 2, 1998 7:51 PM
Power indicator, 1-2
Power port, 1-2
PowerSaver, 1-9
R
Rotation, 1-9
S
Index-2
T
Total Satisfaction, 1-17
Troubleshooting, 1-10
V
Vertical position, 1-7
W
safety instructions
general, 1-iii
Warranties and Return Policy, 1-16
Signal cable, 1-2
Width, 1-7
Dell® 800F Series, 828FI Monitor User’s Guide