User`s guide | Dell NAV3000 GPS Receiver User Manual

2-930SST
Digital Spread Spectrum 900MHz
Cordless Telephone With Caller ID
User’s Guide
1
We bring good things to life.
IMPORTANT INFORMATION
NOTICE: The Industry Canada label identifies certified equipment. This certification means that
the equipment meets certain telecommunications network protective, operational and safety
requirements. The Industry Canada does not guarantee the equipment will operate to the user’s
satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection. The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility
designated by the supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to request the user to
disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power
utility, telephone lines and internal metallic water pipe systems, if present, are connected together.
This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact
the appropriate electric inspection authority, or electrician, as appropriate.
NOTES: This equipment may not be used on coin service provided by the telephone company.
Party lines are subject to telephone company tariffs and, therefore, you may not be able to use
your own telephone equipment if you are on a party line. Check with your local telephone
company.
INTERFERENCE INFORMATION
This equipment generates and uses radio frequency energy which may interfere with residential
radio and television reception if not properly installed and used in accordance with instructions
contained in this manual. Reasonable protection against such interference is ensured, although
there is no guarantee this will not occur in a given installation. If interference is suspected and
verified by switching this equipment on and off, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient the radio/television receiver’s
antenna, relocate the equipment with respect to the receiver, plug the equipment and receiver into
separate circuit outlets. The user may also wish to consult a qualified radio/television technician
for additional suggestions. This equipment has been fully tested and complies with all limits for
Class B computing devices pursuant to part 15 FCC Rules and Regulations. This device complies
with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This
device may not cause interference, and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
HEARING AID COMPATIBILITY
This telephone system meets FCC/Industry Canada standards for Hearing Aid Compatibility.
INDUSTRY CANADA NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
2
TABLE OF CONTENTS
INTRODUCTION ..................................... 4
CORDLESS PHONE INFORMATION .......... 4
CALLER ID INFORMATION ................... 4
MODULAR JACK REQUIREMENTS ......... 5
GETTING STARTED ................................ 5
HANDSET SETUP ............................... 6
DESKTOP INSTALLATION ...................... 7
WALL MOUNT INSTALLATION .............. 8
CORDLESS PHONE BASICS ...................... 9
MAKING A CALL ............................... 9
IN USE INDICATORS ....................... 9
REDIAL ........................................ 9
RECEIVING A CALL ............................ 9
FLASH BUTTON ........................... 10
ADJUSTING THE VOLUME ................. 10
HANDSET EARPIECE VOLUME ......... 10
RINGER VOLUME ......................... 10
SELECTING A RING TONE ................. 10
TEMPORARY TONE .......................... 11
PAGING THE HANDSET ..................... 11
THE MEMORY FEATURE ................... 12
STORING A NUMBER IN MEMORY ... 12
ADDING A PAUSE WHEN YOU STORE
A NUMBER IN MEMORY ............ 13
STORING A TEMPORARY TONE
NUMBER ................................ 14
STORING A CALLER ID RECORD ..... 14
DELETING A STORED NUMBER ....... 14
DELETING ALL STORED NUMBERS
AT ONCE ................................ 15
DIALING A STORED NUMBER ......... 15
DIALING FROM THE DISPLAY .......... 15
DIALING WITH DIRECT DIGIT ENTRY 15
CHAIN DIALING FROM MEMORY ..... 16
HANDSET SOUND SIGNALS ..................
CALLER ID FEATURES & FUNCTIONS .....
CALLER ID DISPLAY FEATURES ..........
REVIEWING CALL RECORDS ...............
DIALING A CALLER ID RECORD ..........
STORING A CALLER ID RECORD
IN MEMORY ................................
DELETING RECORDS ........................
DELETING AN INDIVIDUAL RECORD ..
DELETING ALL RECORDS ...............
VIP RECORDS ................................
STORING A VIP RECORD ..............
REVIEWING VIP RECORDS .............
DIALING A VIP RECORD ...............
DELETING A VIP RECORD .............
DELETING ALL VIP RECORDS ........
CALLER ID MESSAGES ....................
CALL WAITING DISPLAY ...................
FORMATTING LONG DISTANCE
NUMBERS ..................................
ENTERING LOCAL AREA CODE .......
CHANGING THE BATTERY ......................
GENERAL PRODUCT CARE ....................
CAUSES OF POOR RECEPTION ...........
TELEPHONE NETWORK INFORMATION ......
REN NUMBER ...................................
TROUBLESHOOTING GUIDE ...................
ACCESSORY ORDER FORM ...................
INDEX ...............................................
SERVICE ............................................
WARNING: TO PREVENT FIRE
OR ELECTRICAL SHOCK HAZARD,
DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
16
17
17
18
18
18
19
19
19
19
19
20
20
20
20
21
22
23
23
24
25
25
26
26
27
29
31
32
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING
FLASH AND ARROWHEAD WITHIN THE
TRIANGLE IS A
WA R N I N G S I G N
ALERTING YOU OF
"DANGEROUS
VOLTAGE" INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER
(OR BACK). NO USERS E RV I C E A B L E PA R T S I N SIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING
SIGN
ALERTING YOU OF
I M P O R T A N T
INSTRUCTIONS
A C C O M PA N Y I N G
T H E P R O D U C T.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
3
INTRODUCTION
Your GE cordless telephone is designed to give you flexibility in use and
high quality performance. To get the most from your new cordless
telephone, we suggest that you take a few minutes right now to read
through this instruction manual.
CORDLESS PHONE INFORMATION
• Digital Security System
When you place the Handset in the base, the unit verifies it’s security code
which prevents false ringing from other cordless telephones. After a
power outage or battery replacement, you should place the Handset in the
base for about 20 seconds to reset the code.
• IMPORTANT: This Should Not Be The Only Phone in Your Home
Because cordless phones operate on electricity, you should have at least
one phone in your home that is not cordless, in case the power in your
home goes out.
CALLER ID INFORMATION
This device allows you to take advantage of the Caller Identification
Delivery with Call Waiting service that may be available from your local
telephone company. If you do not have this service already installed, you
must contact your local telephone company to arrange to have this service
installed on your line. There is an extra charge to your monthly telephone
bill for this service.
4
GETTING STARTED
Make sure your package includes the items shown below.
Telephone line cord
TALK
NEW #
REPEAT
AM
PM
MEMORY
LOW
JOHN SMITH
DELETE
D
AC power adapter
CHARGE / IN USE
PAGE / FIND
REVIEW
DIAL
VIP
Short telephone
line cord
ENTER
TALK
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
*
OPER
0
FORMAT
TONE
#
REDIAL MEMORY VOLUME FLASH
Base
Handset
Battery (5-2419)
Wall mount bracket
MODULAR JACK REQUIREMENTS
You need an RJ11C (CA11A), type modular jack, which
is the most common type of phone jack and might
look like the one pictured here. If you don’t have a
modular jack, call your local phone company to find
out how to get one installed.
INSTALLATION NOTE: Some cordless telephones operate at frequencies
that may cause interference to nearby TVs and VCRs. To minimize or prevent
such interference, the base of the cordless telephone should not be placed
near or on top of a TV or VCR. If interference continues, moving the cordless
telephone farther away from the TV or VCR will often reduce or eliminate the
interference.
5
HANDSET SETUP
1. Remove the battery compartment door.
2. Insert the battery into the compartment.
3. Install the battery compartment door.
4. Plug the power supply cord into the 9V
DC jack on the base and into an AC
outlet.
5. Place the handset in the base (facing
either up or down) to charge for 12
hours.
a) Base Unit on Desk- Charging of
handset can be done with handset facing
either Up or Down.
b) Base Unit at Wall Mount- Charging of
handset can be done ONLY in face-up
position.
IMPORTANT: If you do not charge the
handset battery properly (for 12 hours)
when you first set up the phone, the
battery’s long-term performance will be
compromised.
10:51 A.M. 8/11
REPT CALL
NEW MEMO
#
25
JOHN SMITH
DELETE
D
ENTER
REVIEW
DIAL
VIP
TALK
1
GHI
4
PQRS
7
*
ABC
2
DEF
3
JKL
5
MNO
6
TUV
8
WXYZ
9
OPER
0
CHARGE / IN USE
FORMAT
TONE
REDIAL MEMORY VOLUME FLASH
6
CHARGE / IN USE
PAGE / FIND
#
PAGE / FIND
DESKTOP
INSTALLATION
6
4
5
1
3
2
TONE/PULSE
switch
1. Plug the power supply cord into the 9V DC jack on the base and into an
AC outlet.
2. Set the TONE/PULSE switch to TONE for touch-tone service, or PULSE
for rotary service. If you don’t know which type of service you have,
check with the phone company.
3. Raise the base antenna.
4. Select RINGER ON or OFF (on the side of handset). When you select
OFF, the handset doesn’t ring.
5. Place handset in the base to charge for 12 hours. The CHARGE/IN
USE light comes to indicate that the battery is charging.
If you don’t charge the handset battery properly (for 12 hours)
when you first set up the phone, the battery’s long-term
performance will be compromised.
6. Plug the telephone line cord into the PHONE LINE jack on the back of
the base and into a modular jack.
NOTE: Use only the Thomson AC power adapter (5-4083) that came with this
unit. Using other adapters may damage the unit.
7
WALL MOUNT INSTALLATION
1. Plug the short telephone line cord into the
PHONE LINE jack on the back of the base
and connect the other end to a wall jack.
2
5
1
2. Plug the power supply cord into the 9V DC
jack on the base and plug the power
supply into an AC outlet.
3. Feed the short line cord through the notch
at the top of the wall mount bracket so that
it comes through the square opening on
the bracket. Then feed the power supply
cord through both the top and bottom
notches on the bracket.
4
3
4. Attach the wall mount bracket by putting
the tabs into the slots on the top of the unit
and then snap the tabs at the bottom of the
wall mount bracket into place.
6. Raise the base antenna.
8
RINGER ON/OF
F
5. Slip the mounting holes over the wall plate
posts and slide the unit down firmly into
place. (Wall plate not included.)
7. Set the TONE/PULSE switch to TONE for
touch-tone service, or PULSE for rotary
service. If you don’t know which type of
service you have, check with the phone
company.
8. Select RINGER ON or OFF (on the side of
handset). When you select OFF, the
handset doesn’t ring.
9. Place handset in the base to charge for 12 hours. The CHARGE/IN USE light
comes on indicating that the battery is charging.
If you don’t charge the battery properly (for 12 hours) when you first
set up the phone, the battery’s long-term performance will be
compromised.
8
CORDLESS PHONE BASICS
MAKING A CALL
After initial set up, the handset battery
should be charged for at least 12 hours.
The only two things you need to know to
make a call are:
• Press the TALK button before you dial.
If you try to make a call when you’re
too far away from the base, the
handset beeps.
• Press TALK or place the handset in the
base to hang up.
TALK
D
TALK
button
REVIEW
TALK
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
FORMAT
*
TONE
• The CHARGE/IN USE light on the base
blinks.
• The Phone Symbol appears in the
display.
ENTER
DIAL
VIP
• The TALK button on the handset lights.
MEMORY
LOW
JOHN SMITH
DELETE
IN USE INDICATORS
NEW #
REPEAT
AM
PM
Phone
symbol
OPER
0
#
REDIAL MEMORY VOLUME FLASH
REDIAL
button
REDIAL
Press the TALK button, then press the
REDIAL button to redial the last number
(up to 32 digits) you called.
RECEIVING A CALL
1. Check the display for Caller ID
information.
CHARGE / IN USE
CHARGE/
IN USE
light
PAGE / FIND
2. Press TALK to answer a call.
9
FLASH BUTTON
Use the FLASH button to activate custom
calling services such as call waiting or call
transfer, which are available through your
local phone company.
IMPORTANT: Don't use the TALK button to
activate custom calling services such as call
waiting, or you’ll hang up the phone.
ADJUSTING THE VOLUME
The VOLUME button on the handset to
control the volume of the handset’s
earpiece and the ringer volume.
HANDSET EARPIECE VOLUME
To change the volume of the handset’s
earpiece, press VOLUME while the phone is
in use.
TALK
NEW #
REPEAT
AM
PM
MEMORY
LOW
JOHN SMITH
DELETE
D
ENTER
REVIEW
DIAL
VIP
TALK
RINGER VOLUME
To adjust the ringer volume, press the
VOLUME button when the phone is onhook (phone is inactive, TALK light is off).
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
FORMAT
SELECTING A RING TONE
*
TONE
OPER
0
#
REDIAL MEMORY VOLUME FLASH
There are 3 ring tones built into your
phone. To choose a ring tone, press FLASH
followed by either 1, 2, or 3 when the
phone is on-hook (phone is inactive, TALK
light is off).
10
VOLUME
button
FLASH
button
TEMPORARY TONE
This feature enables people who have
pulse (rotary) service to access touchtone services offered by banks, credit
card companies, etc., by pressing the
tone button to temporarily make the
phone touch-tone compatible. To get
information about your bank account, for
example, you would:
TALK
DELETE
ENTER
D
TALK
button
REVIEW
DIAL
VIP
3. Press the TONE button after your call is
answered.
4. Follow the bank’s voice instructions to
complete your transaction.
MEMORY
LOW
JOHN SMITH
1. Press the TALK button.
2. Call the bank’s information line.
NEW #
REPEAT
AM
PM
TALK
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
FORMAT
*
TONE
TONE
button
OPER
0
#
REDIAL MEMORY VOLUME FLASH
5. Hang up when finished. The phone
returns to pulse (rotary) service.
PAGING THE HANDSET
Press the PAGE button on the base to get
the attention of somebody who is using
the handset or to locate a misplaced
handset.
When you press PAGE on the base, the
handset beeps (the CHARGE/IN USE light
on the base blinks).
Press the TALK button when you locate
the handset to stop the PAGE feature.
Remember that the RINGER switch on the
side of the handset must be ON in order
for the handset to beep.
CHARGE / IN USE
PAGE / FIND
PAGE
button
CHARGE/
IN USE
light
11
THE MEMORY FEATURE
Store up to 20 numbers in memory for
quick dialing.
STORING A NUMBER IN MEMORY
1. Make sure that the phone is OFF.
2. Press the MEMORY button (SEL MEM
ENTRY? appears in the display).
3. Use the REVIEW buttons (
) to
select an empty memory location, and
then press the < and > buttons
(VOLUME and FLASH) to put the
phone in memory edit mode
or
Use the digits for direct memory
location entry (01-20), and then press
MEMORY put the phone into memory
edit mode.
• The phone goes into memory edit
mode and ENTER NUMBER appears in the
display.
Memory
location
number
Use
DELETE to
correct entry
errors
TALK
MEMORY
LOW
JOHN SMITH
DELETE
D
Use”1” to
add a
space in a
name
NEW #
REPEAT
AM
PM
ENTER
REVIEW
DIAL
VIP
TALK
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
FORMAT
4. Use the digits to enter a telephone
number (up to 16 digits).
*
TONE
OPER
0
#
REDIAL MEMORY VOLUME FLASH
• Use the < and > buttons (VOLUME
and FLASH) to move across the
screen.
• Use DELETE to delete a number.
5. Press MEMORY after you have entered
the number.
• ENTER NAME appears in the display.
12
MEMORY
button
Use VOLUME and
FLASH to scroll
across the screen.
6. Use the digits (2-9) and the < > buttons to
enter a name.
a. Each number on the keypad has
corresponding letters. Each time you
press the digit, it scrolls to the next
letter for that digit. (For example to
enter the letter “C”, you would press
the digit “2” three times).
b. Press > (FLASH button) or a new digit
to move to the next letter in the name.
c. Use the number 1 to insert a space,
and use DELETE to correct errors.
7. When the name is complete, press
MEMORY to store the name and number.
• Two beeps indicates successful
operation.
ADDING A PAUSE WHEN YOU STORE A
NUMBER IN MEMORY
Use the REDIAL button to insert a pause in
the dialing sequence when you store a
number (for example, when you must dial 9
to get an outside line or enter codes to
access your bank’s information line).
13
VIP
STORING A TEMPORARY TONE NUMBER
TALK
1. Press the MEMORY button.
2. Press any (2 digit) number (01-20) to store
the dialed number in that memory
location.
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
FORMAT
3. Press MEMORY again.
4. Dial the number (up to 16 digits).
TONE
button
*
TONE
OPER
0
#
REDIAL MEMORY VOLUME FLASH
5. Press the TONE button to switch to tone
dialing. (The TONE counts as one digit.)
6. Enter authorization code/access
numbers.
7. Press MEMORY.
REDIAL
button
MEMORY
button
STORING A CALLER ID RECORD
You can store a caller ID record in memory.
See the “Caller ID Features & Functions”
section for details.
DELETING A STORED NUMBER
1. Press the MEMORY button.
2. Use the REVIEW buttons (
) to select
the desired memory location, or use the
digits for direct entry (01-20).
Display
TALK
3. Press the DELETE button. (DELETE ENTRY?
appears in the display.)
DELETE
4. Press DELETE again to confirm.
NEW #
REPEAT
AM
PM
MEMORY
LOW
JOHN SMITH
DELETE
button
D
VIP
ENTER
REVIEW
DIAL
TALK
REVIEW
buttons
14
DELETING ALL STORED NUMBERS AT ONCE
1. Press the MEMORY button.
2. Use the REVIEW buttons (
) to select the desired memory location,
or use the digits for direct entry (01-20).
3. Press and hold the DELETE button. (DELETE ALL ??? appears in the display.)
4. Press DELETE again to confirm.
DIALING A STORED NUMBER
You can dial a stored number by selecting it from the display, or through
direct digit entry.
DIALING FROM THE DISPLAY
1. Make sure the phone is off.
2. Press MEMORY.
3. Use the REVIEW buttons (
) to select the desired memory location.
4. Press the DIAL button.
DIALING WITH DIRECT DIGIT ENTRY
1. Press the TALK button to get a dial tone.
2. Press MEMORY.
3. Press any 2-digit memory location number (01-20).
15
CHAIN DIALING FROM MEMORY
Use this feature to make calls which require a sequence of numbers, for
instance if you use a calling card for a frequently called long distance
number. Basically, you dial each part of the sequence from memory. The
following example shows how you can use chain dialing to make a call
through a long distance service:
The Number For
Memory Location
Long distance access number
Authorization code
Frequently called long distance number
07
08
09
1. Press the TALK button to get a dial tone.
2. Press the MEMORY button and then press 07.
3. When you hear the access tone, press MEMORY and then press 08.
4. At the next access tone, press MEMORY and then 09.
HANDSET SOUND SIGNALS
Signal
Meaning
Two beeps - continuous (phone off)
Soft double-beeps in the earpiece (phone on)
A long warbling tone (with ringer on)
Intermittent short beep
Page signal
Page Signal
Incoming call signal
Battery low
16
CALLER ID FEATURES & FUNCTIONS
The Caller ID feature lets you screen calls as they come in and also stores
records of calls that are received. Here are some of the features available:
• Callback – Dial a Caller ID record’s number.
• VIP Numbers – Store up to 5 VIP numbers so you can quickly see if
those people have called you.
• VIP Ring – A distinctive ring tone occurs when you receive a call from a
VIP caller.
• Memory Storage – Store in memory a Caller ID record’s number.
• Long Distance Formatting – Format a Caller ID record for long distance
callback.
• Call Waiting – Accept call waiting calls (if the service is available).
• CID Records – Store up to 40 Caller ID records.
CALLER ID DISPLAY FEATURES
HANDSET
BASE
• Caller’s telephone number
• CHARGE/IN USE light
flashes rapidly when you
have new or unread
messages
• Caller’s name (if available)
• Caller ID Error Messages
• Date and Time of the call
• Whether the call is new or a repeat call
Time
Date
TALK
AM
PM
New or
Repeat call
NEW #
REPEAT
Call number
MEMORY
LOW
Caller’s number
JOHN SMITH
Caller’s Name (if available) and
Caller ID Error Messages
17
REVIEWING CALL RECORDS
Each time someone calls, their call is stored
in the Caller ID memory (up to 40 calls).
• Press REVIEW
to review the caller list
from the oldest record to the newest
• Press REVIEW
to review the caller list
from the newest record to the oldest.
TALK
NEW #
REPEAT
AM
PM
MEMORY
LOW
DIAL
button
JOHN SMITH
DIALING A CALLER ID
RECORD
DELETE
D
ENTER
REVIEW
DIAL
VIP
REVIEW
buttons
TALK
To dial the number in a record:
1. Use the REVIEW buttons (
the record you want to dial.
) to select
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
2. Press the DIAL button.
FORMAT
STORING A CALLER ID
RECORD IN MEMORY
*
TONE
OPER
0
1. Use the REVIEW buttons (
) to select
the record you want to store in memory.
2. Press the MEMORY button to put the
handset into memory mode.
3. Use the REVIEW buttons (
) to select
the desired memory location.
4. Press MEMORY to store the record.
18
#
REDIAL MEMORY VOLUME FLASH
MEMORY
button
DELETING RECORDS
When 40 records have been stored, new
calls are added to the beginning of the
caller list, and the oldest calls are deleted.
You can also manually delete records.
DELETING AN INDIVIDUAL RECORD
1. Use the REVIEW buttons (
) to select
the record you want to delete.
2. Press the DELETE button. (DELETE ENTRY?
appears in the display.)
3. Press DELETE again to confirm.
Message
display
TALK
NEW #
REPEAT
AM
PM
MEMORY
LOW
JOHN SMITH
DELETE
DELETE
button
D
VIP
REVIEW
ENTER
DIAL
TALK
DELETING ALL RECORDS
REVIEW
buttons
1. Use the REVIEW buttons (
) to select
the record you want to delete.
2. Press and hold the DELETE button.
(DELETE ALL? appears in the display.)
3. Press DELETE again and hold until a
double confirmation beep is heard.
VIP RECORDS
You can store as many as five records into a
VIP list for easier access.
TALK
STORING A VIP RECORD
1. Use the REVIEW buttons (
) to select
the record you want to add to the VIP list.
2. Press the VIP button.
3. Use the REVIEW buttons (
the a VIP location.
NEW #
REPEAT
AM
PM
MEMORY
LOW
JOHN SMITH
DELETE
D
VIP
) to select
4. Press VIP again to store the record.
VIP
button
ENTER
REVIEW
DIAL
TALK
REVIEW buttons
19
REVIEWING VIP RECORDS
1. Press the VIP button.
2. Press REVIEW
to review the VIP list
from the oldest record to the newest, and
press REVIEW
to review the VIP list
from the newest record to the oldest.
DIALING A VIP RECORD
1. Press the VIP button.
2. Press REVIEW (
list.
)to review the VIP
3. Select the record you want to dial, and
then press DIAL.
DIAL
button
TALK
DELETING A VIP RECORD
1. Press the VIP button.
2. Press REVIEW (
list.
DELETING ALL VIP RECORDS
1. Press the VIP button.
)to review the VIP
3. Press and hold the DELETE button.
(DELETE ALL? appears in the display.)
4. Press DELETE again to confirm.
20
DELETE
D
VIP
VIP
button
4. Press DELETE again to confirm.
2. Press REVIEW (
list.
DELETE
button
)to review the VIP
3. Select the record you want to delete, and
then press DELETE. (DELETE ENTRY? appears
in the display.)
NEW #
REPEAT
AM
PM
MEMORY
LOW
JOHN SMITH
ENTER
REVIEW
DIAL
TALK
REVIEW buttons
CALLER ID MESSAGES
The following indicators show the status of a message or the unit.
New 3
Repeat 10
Total 40
There are 40 total calls stored in your phone’s Caller ID
memory, 3 of them are new calls and 10 repeat.
Change AREA CODE from Prompt asking you to enter your area code when you
317 to – –␣ –
set up your Caller ID.
PAGE
Your handset is being paged from the base.
LOW BATTERY
Your phone battery needs recharging.
Delete Entry?
Prompt asking you if you want to erase a Caller ID record.
DELETED
Confirms that a Caller ID record has been deleted.
Delete ALL???
Prompt asking you if you want to erase all Caller ID
records.
*** EMPTY***
Space is available to store name and number in memory.
Invalid CID
Caller information has been interrupted during
transmission or the phone is excessively noisy.
OUT OF AREA
The call comes from an area with no Caller ID service.
OUT OF RANGE
Your handset is too far from the base.
PRIVATE
The person is calling from a number that has been
blocked from transmission.
PHONE
The TALK button has been pressed and there is a
dial tone.
01 : 29 VOL :
Shows phone has been turned ON for 1 minute and 29
seconds. Volume is at level 4.
21
CALL WAITING DISPLAY
To utilize the full capabilities of this unit,
you must have Caller ID with name and
number delivery as well as Call Waiting
Deluxe (Call Waiting with Caller ID) service
installed. This unit will let you know when
a call is waiting as well as who is calling
before you answer.
This unit does not provide Caller ID and
Call Waiting features unless services have
been ordered from your local telephone
company at a monthly charge. Check with
your local telephone company to confirm
both of these services are available. If you
only have Caller ID service, this unit will
not receive and display Call Waiting with
Caller ID information.
TALK
3. If you choose not to answer the call, the
Call Waiting Caller ID information will be
stored for future reference.
4. When you finish the call waiting call,
press FLASH again to go back to the
original call.
22
MEMORY
LOW
JOHN SMITH
DELETE
D
ENTER
REVIEW
DIAL
VIP
1. When you receive a call waiting call,
check the display to see who is calling.
2. Press the FLASH button to answer the
call.
NEW #
REPEAT
AM
PM
TALK
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
FORMAT
*
TONE
OPER
0
#
REDIAL MEMORY VOLUME FLASH
FLASH
button
FORMATTING LONG DISTANCE
NUMBERS
ENTERING LOCAL AREA CODE
NOTE: In order for the CALL BACK feature to
operate properly, you MUST initially enter
your local 3-digit area code.
1. Press REVIEW
button.
2. Press “*” button.
TALK
3. Enter the desired 3-digit area code.
You may need to add the area code (or 1+
area code) to some numbers in order to
dial them.
1. Use the REVIEW buttons (
the record you want to dial.
• Press FORMAT (#) once to add the
area code (i.e. 123-456-7890)
• Press FORMAT (#) again to add 1 plus
the area code (i.e. 1-123-456-7890)
MEMORY
LOW
JOHN SMITH
DELETE
D
ENTER
REVIEW
DIAL
VIP
) to select
2. Use the FORMAT (#) button to scroll
through the options:
NEW #
REPEAT
AM
PM
DIAL
button
TALK
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
FORMAT
*
TONE
OPER
0
#
FORMAT
button
• Press FORMAT (#) a third time to go
back to the 7-digit number (i.e. 4567890).
3. Press DIAL to dial the number.
23
CHANGING THE BATTERY
Your cordless handset is powered by a nickel cadmium battery pack
(#5-2419). The battery pack needs to be recharged periodically. A fully charged
battery gives you approximately 4 hours of talk time or 7 days of stand-by
time. Return the handset to the base whenever possible to keep the battery
adequately charged.
The handset runs on a consumer-replaceable, nickel-cadmium battery pack. If
you experience any of the following problems, you may need to replace the
battery pack: short talk time, poor sound quality, limited range, CHARGE/IN
USE light fails to light. Make sure phone is OFF before you replace battery.
1. Remove the battery compartment
door.
2. Remove the battery pack.
3. Insert the new battery into the
compartment on the back of the
handset.
4. Replace the battery compartment
door.
5. Return the handset to the base unit
for at least 12 hours to adequately
charge a new battery pack.
BATTERY SAFETY PRECAUTIONS
• Don’t disassemble, mutilate,
puncture, wet, or dispose of
battery in fire. Like other batteries
of this type, if it is burned or
punctured, it could release toxic
materials which can cause injury.
• Keep batteries out of the reach of
children.
24
NOTE: This product
contains a nickelcadmium rechargeable battery and must
be recycled or
disposed of properly.
We suggest that you
check with your local
Environmental
Agency regarding
recycling or disposal.
Contains
Nickel-Cadmium
Rechargeable Battery
Ni-Cd
Must be Recycled or
Disposed of Properly
GENERAL PRODUCT CARE
To keep your telephone working and looking good, follow these guidelines:
• Avoid putting the phone near heating appliances and devices that generate
electrical noise (for example, motors or fluorescent lamps).
• DO NOT expose to direct sunlight or moisture.
• Avoid dropping the handset, as well as other rough treatment to
the phone.
• Clean the phone with a soft cloth.
• Never use a strong cleaning agent or abrasive powder because this will
damage the finish.
• Retain the original packaging in case you need to ship the phone at a later date.
• Periodically clean the charge contacts on the handset and base with a soft
cloth.
CAUSES OF POOR RECEPTION
•
•
•
•
•
•
•
•
•
Aluminum siding.
Foil backing on insulation.
Heating ducts and other metal construction can shield radio signals.
You’re too close to appliances such as microwaves, stoves,
computers, etc.
Atmospheric conditions, such as strong storms.
Base is installed in the basement or lower floor of the house.
Base is plugged into an AC outlet with other electronic devices.
Handset battery is low.
You’re out of range of the base.
25
TELEPHONE NETWORK INFORMATION
Should your equipment cause trouble on your line which may harm the
telephone network, the telephone company, where practicable, may notify
you that temporary discontinuance of service may be required. Where
prior notice is not practicable and the circumstances warrant such action,
the telephone company may temporarily discontinue service immediately.
The telephone company may make changes in its communications
facilities, equipment, operations or procedures where such action is
required in the operation of its business. If these changes are expected to
affect the use or performance of your telephone equipment, the telephone
company will likely give you adequate notice to allow you to maintain
uninterrupted service.
Notice must be given to the telephone company upon termination of your
telephone from your line.
REN NUMBER
On the bottom of this equipment is a label indicating, among other
information, the FCC Registration number and Ringer Equivalence Number
(REN) for the equipment. You must, upon request, provide this information
to your telephone company.
The REN is useful in determining the number of devices you may connect
to your telephone line and still have all of these devices ring when your
telephone number is called. In most (but not all) areas, the sum of the
RENs of all devices connected to one line should not exceed 5. To be
certain of the number of devices you may connect to your line as
determined by the REN, you should contact your local telephone company.
26
TROUBLESHOOTING GUIDE
In case of difficulty, please check the following Troubleshooting Guide
before seeking service.
Problem
Solution
No dial tone
• Check installation:
— Is the base power cord connected to a working outlet?
— Is the telephone line cord connected to the base unit and
the wall jack?
• Disconnect the base from the wall jack and connect
another phone to the same jack. If there is no dial tone in
the second phone, the problem might be your wiring or
local service.
• Is the battery pack installed correctly?
• Did the handset beep when you pressed the TALK
button? Did the TALK light come on? The battery may
need to be charged.
• Make sure the battery is properly charged (12 hours).
• Is the handset out of range of the base? Move closer to
the base unit.
• Place handset in base for 10 seconds to reset the phone.
• If the phone still does not work, disconnect the power
cord and remove the battery pack. Then reconnect the
power cord and reinstall the battery pack. Place handset
in the base for 10 seconds to allow it to re-initialize.
Dial tone is OK, but
• Make sure the TONE/PULSE switch on the base is set
can’t dial out
correctly.
Handset does not ring • Make sure the RINGER ON/OFF switch on the base is
turned to ON.
• You may have too many extension phones on your line.
Try unplugging some phones.
• See solutions for “No dial tone.”
27
Problem
Solution
Cannot hear phone
You experience
noise, or fading in
and out
•
•
•
•
•
Unit beeps
•
•
•
•
Cannot hear the
PAGE/FIND tone
Range is shorter
Battery will not hold
a charge
Memory Dialing
does not work
28
•
•
•
Press VOLUME button on the handset.
Charge battery.
Is handset out of range? Move closer to the base.
Relocate the base unit away from TV’s computers, micro
waves or any other appliances or electronic devices that
may cause interference.
Make sure base is not plugged into an outlet with
another household appliance.
You may be receiving an out-of-range alert, move closer
to the base.
Place handset in base for 10 seconds to reset the
phone. The CHARGE/IN USE comes on when reset is
successful.
Put handset in base for 12 hours to recharge battery.
Clean charging contacts on handset and base with a soft
cloth or an eraser.
See solutions for “No dial tone.”
Replace battery.
Set the RINGER to ON.
• Position the base antenna upward.
than normal
• Be sure you are sufficiently charging the battery. Make
sure the battery has been charged for 12 hours
• Make sure battery contacts on both the handset and the
base are making contact and are clean; free of dirt or lint.
• When the handset is placed in the base, make sure that
the base CHARGE/IN USE light is on.
• Memory location must be 2 digits (i.e, 01,02, etc.).
• Did you program the memory location keys correctly?
• Did you follow proper dialing sequence?
• Make sure TONE/PULSE switch is correctly set.
29
5-2419
5-4083
TOTAL
City ________________________State________ ZIP_________________
Address_____________________________________ Apt.____________
Name________________________________________________________
To:
This is your return label. Please print clearly.
Ronks, PA 17573-8419
P.O. Box 8419
Mail Order Department
Consumer Electronics
Mail order form and money order or check (in U.S. currency)
made payable to Thomson Consumer Electronics, Inc. to:
Total Amount Enclosed.................................$_______________
Shipping, Handling, and Insurance............. $_______________
$5.00
All accessories are subject to availability. Where applicable, we will ship a
superseding model.
Use VISA or MasterCard preferably. Money order or check must be in U.S. currency
only. No COD or Cash.
Sales Tax................................................... ... $_______________
We are required by law to collect the appropriate sales tax for
each individual state, county, and locality to which the
merchandise is being sent.
Total Merchandise...........................................$_______________
*Prices are subject to change without notice.
Please make sure that this form has been filled out completely.
Authorized Signature
____________________________________________________________________
My card expires:
Copy the number above your
name on the MasterCard
Copy your complete account number from your MasterCard.
My card expires:
Copy your complete account number from your VISA card.
QUANTITY
✂
Duties will apply for shipments to Canada.
PRICE*
$27.55
$14.95
CATALOG NUMBER
Your complete charge card number, its expiration date and your
signature are necessary to process all charge card orders.
For credit card purchases
AC power adapter (black)
DESCRIPTION
Replacement handset battery
ACCESSORY ORDER FORM
CUSTOMER: CUT ALONG DOTTED LINE.
30
INDEX
A
F
R
Accessory Order Form 29
Adding a Pause When
You Store a Number in
Memory 13
Flash Button 10
B
H
Receiving a Call 9
Redial 9
REN Number 26
Ring Tone 10
Ringer Volume 10
Battery 24
Battery installation 6
Handset display 17
Handset Earpiece
Volume 10
Handset Setup 6
Handset sound signals 16
Hearing Aid
Compatibility 2
C
Call Waiting Display 22
Caller ID 17
Call Waiting feature 22
Deleting a record 19
Dialing a Caller ID
record 18
Display 17
Reviewing records 18
Storing a record in
memory 18
Storing a record 14
VIP records 19
deleting 20
dialing 20
reviewing 20
storing 19
Caller ID Messages 21
Chain dialing stored
numbers 16
Changing the Battery 24
D
Deleting Caller ID records
19
Deleting stored
numbers 14, 15
Dialing a stored
number 15
Digital Security
System 4
G
General Product Care 25
I
Installation, desktop 7
Important
Information 2
Interference
Information 2
M
Making a call 9
Memory Feature 12
Deleting a stored
number 14
Storing a Caller ID
number 18
Storing a Caller ID
record 14
Modular Jack
Requirements 5
P
Paging 11
Pause 13
Poor Reception 25
S
Selecting a Ring Tone 10
Service 32
Stored number,
deleting 14
Storing a caller ID record
in memory 14
Storing a Number in
Memory 12
Storing a Temporary Tone
Number in Memory 14
T
Talk light 9
Telephone Network
Information 26
Temporary Tone 11
Troubleshooting
Guide 27
V
VIP records 19
Deleting 20
Dialing 20
Reviewing 20
Storing 19
Volume, handset 10
W
Wall Mount Installation 8
31
SERVICE
Thomson Consumer Electronics Canada, Inc. warrants to the purchaser or gift
recipient that if any manufacturing defect becomes apparent in this product within
1 year from the original date of purchase, it will be replaced free of charge,
including return transportation.
This warranty does not include damage to the product resulting from accidents,
misuse or leaking batteries.
Should your product not perform properly during the warranty period, either:
1. Return it to the selling dealer with proof of purchase for replacement,
OR
2. Remove the batteries (where applicable), and pack product complete with
accessories in the original carton (or equivalent).
— Mail prepaid (with proof of purchase) and insured to:
Thomson Consumer Electronics Canada, Inc.
Distribution Centre
7400 A Bramalea Road
Mississauga, Ontario L5S 1X1
The provisions of this written warranty are in addition to and not a modification of
or subtraction from the statutory warranties and other rights and remedies
contained in any applicable legislation, and to the extent that any such provisions
purport to disclaim, exclude or limit any such statutory warranties and other rights
and remedies, such provisions shall be deemed to be amended to the extent
necessary to comply therewith.
If you are unable to find a qualified servicer for out of warranty service, you may
write to:
Thomson Consumer Electronics Canada, Inc.
P.O. Box 0944
Indianapolis, Indiana, U.S.A., 46206-0944
Attach your sales receipt to this booklet for future reference. This information is
required if service is needed during the warranty period.
PURCHASE DATE ____________________________________________________________
NAME OF STORE ____________________________________________________________
Model 2-930SST
15362160 (Rev. 2 E/F)
98-52
Printed in Thailand
© 1998 Thomson Consumer Electronics, Inc.
Trademark(s) ® Registered
Marque(s) ® déposée(s)
Download PDF

advertising