Dell PCM8024-k Switch User Manual

DELL PowerConnect™
PCM6220/PCM8024/PCM6348
PCM8024-k/PC8024/
PC8024F/PC7000 Series
Firmware CLI Transition Guide
A Dell Technical White Paper
Dell PowerConnect™ Firmware CLI Transition Guide
Notes, Notices, and Cautions
A NOTE indicates important information that helps you make better use of your computer.
A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
A CAUTION indicates a potential for property damage, personal injury, or death.
THIS WHITE PAPER IS FOR INFORMATIONAL PURPOSES ONLY, AND MAY CONTAIN TYPOGRAPHICAL
ERRORS AND TECHNICAL INACCURACIES. THE CONTENT IS PROVIDED AS IS, WITHOUT EXPRESS OR
IMPLIED WARRANTIES OF ANY KIND.
© 2011 Dell Inc. All rights reserved. Reproduction of this material in any manner whatsoever without
the express written permission of Dell Inc. is strictly forbidden. For more information, contact Dell.
Dell, the DELL logo, and the DELL badge, and PowerConnect are trademarks of Dell Inc. Other
trademarks and trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade
names other than its own.
Model PCM6220, PCM8024, PCM8024-k, PCM6348, PC8024, PC8024F, PC7000 Series
Rev A00
April 6, 2011
Page ii
Dell PowerConnect™ Firmware CLI Transition Guide
Contents
A Dell Technical White Paper ......................................................................................... i
Introduction................................................................................................................. 2
Changes to the Interface Naming Convention ........................................................................2
Ethernet Interfaces ..................................................................................................... 2
Port Channel Interfaces ................................................................................................3
Loopback Interfaces ....................................................................................................3
VLAN Interfaces ......................................................................................................... 3
Tunnel Interfaces ....................................................................................................... 3
Migration Key Concepts ................................................................................................... 3
Commands That Did Not Migrate ..................................................................................... 3
Slot Naming Conventions ..............................................................................................3
Ethernet Configuration Commands ..................................................................................3
VLANs...................................................................................................................... 3
Management Interfaces ................................................................................................4
Updated Commands – Operational Modifications ....................................................................5
Updated Commands – Command Mode Modifications ...............................................................8
Updated Commands – Syntax Modifications ......................................................................... 10
Deprecated Commands ................................................................................................. 18
Tables
Table 1: Interface Identifiers ............................................................................. 2
April 6, 2011
Page 1
Dell PowerConnect™ Firmware CLI Transition Guide
Introduction
The Dell™ PowerConnect CLI Transition Guide White Paper discusses the changes in the CLI commands
from the PowerConnect 6200 and 8024 3.x software to the 4.x software release on the 6200, 7000, and
8000 Series switches. Some changes were syntactical only and some were functional as specified in the
following sections.
NOTE: Not all commands are available on all switches. Refer to the DELL POWER CONNECT CLI REFERENCE
GUIDE for commands specific to your switch model.
Changes to the Interface Naming Convention
Changes to the Interface Naming Conventions are applicable to all switches. The conventions for
naming interfaces in CLI commands are described in the following sections.
Ethernet Interfaces
The gigabit Ethernet and 10-gigabit Ethernet ports are identified in the CLI by the variable
unit/slot/port, where:
•
<Interface Type> Unit#/Slot#/Port#—Identifies a specific interface by the interface type
tag followed by the Unit# followed by a / symbol, then the Slot# followed by a / symbol,
and then the Port#. For example, gi2/0/10 identifies the gigabit port 10 in slot 0 on unit
2. Table 1 below lists the supported interface type tags.
• Unit #—The unit number is greater than 1 only in a stacking solution where a number of
switches are stacked to form a virtual switch. In this case, the Unit# indicates the logical
position of the switch in a stack. The range is 1–12. The unit value is 1 for standalone
switches.
• Slot #—The slot number is an integer number assigned to a particular slot. Fixed ports are
in slot 0. The expansion slots use slot numbers 1 or 2. Use the show slot command to
retrieve information for a particular slot.
• Port #—The port number is an integer number assigned to the physical port on the switch
and corresponds to the number printed next to the port. Ports are numbered from 1 to
the maximum number of ports available on the switch, typically 24 or 48.
Within the CLI REFERENCE GUIDE, the tag interface–id refers to an interface identifier that follows the
naming convention above.
Table 1: Interface Identifiers
Interface Type
Long Form
Short Form
Identifier
Gigabit Ethernet
gigabitethernet
gi (gi was g)
unit/slot/port
10–Gigabit Ethernet
tengigabitethernet
te (te was xg)
unit/slot/port
Loopback
loopback
lo
Loopback-id (0–7)
Port Channel
port-channel
po
port-channel-number
Tunnel
tunnel
tu
tunnel-id (0–7)
VLAN
vlan
vl
vlan-id (1–4093)
When listed in command line output, gigabit Ethernet interfaces are preceded by the characters Gi,
and 10-gigabit Ethernet interfaces are preceded by Te.
April 6, 2011
Page 2
Dell PowerConnect™ Firmware CLI Transition Guide
Port Channel Interfaces
Port-channel (or LAG) interfaces are represented in the CLI by the variable port-channel-number,
which can assume values from 1–48.
When listed in command line output, port channel interfaces are preceded by the characters Po.
Loopback Interfaces
Loopback interfaces are represented in the CLI by the variable loopback-id, which can assume values
from 0–7.
VLAN Interfaces
VLAN interfaces are represented in the CLI by the variable vlan-id, which can assume values from 1–
4093.
Tunnel Interfaces
Tunnel interfaces are represented in the CLI by the variable tunnel-id, which can assume values from
0–7.
Refer to the Interface Naming Conventions section of the CLI REFERENCE GUIDE.
Migration Key Concepts
The 4.x software was designed for the migration to require minimal user intervention. Migration issues
documented here are applicable across all platforms.
Commands That Did Not Migrate
Some commands did not migrate to the 4.x software. Some old commands no longer exist; some
commands have been deprecated by a new command or removed entirely. A list of these commands is
provided in Deprecated Commands on page 18.
Slot Naming Conventions
Along with the interface naming convention changes are the slot naming convention changes. The old
method was unit/type port, for example 1/g1. The new method is interface type unit/slot, based on
industry-standard naming convention, e.g., Gigabit Ethernet (Gi) 1/0/1.
Port channels old method ch1 or port-channel 1, depending on where you were in CLI. The new
abbreviation for port-channel is “po”.
Ethernet Configuration Commands
There is no longer a negotiation command. Effective with the 4.x software, auto-negotiation is
configured as part of the speed and duplex commands. Refer to the descriptions of the speed and
duplex commands in the CLI REFERENCE GUIDE.
VLANs
In version 4.x, there is a distinction between Layer 2 and Layer 3 configuration. Interface VLAN
Configuration mode is used only for Layer 3 configuration.
April 6, 2011
Page 3
Dell PowerConnect™ Firmware CLI Transition Guide
Management Interfaces
There is no longer a preconfigured management VLAN on the switch. Effective with the 4.x software,
the administrator can configure a management VLAN on the in-band interfaces, but the VLAN should
not be enabled for routing. The ip address command in Global Config mode no longer exists.
The ability of the switch to obtain an address via DHCP is no longer restricted to a single interface.
Effective with the 4.x software, the embedded DHCP client can be enabled on more than one interface
at a time. DHCP now works on any routing interface. For example, DHCP can operate on a routing
interface and out-of-band (OOB) at the same time. Therefore, DHCP can obtain a switch address over
more interfaces than before.
April 6, 2011
Page 4
Dell PowerConnect™ Firmware CLI Transition Guide
Updated Commands – Operational Modifications
Feature
Previous Implementation
Dell™ PowerConnect 4.x
Implementation
Comments
ARP
arp timeout seconds
arp timeout seconds
In the revised implementation,
the command is supported in
both Global Configuration Mode
and Interface Configuration
Mode, while previous
implementation supported only
Global Configuration Mode. This
capability gives administrators
the ability to adjust the ARP
timings to better operate on
subnets with different
performance requirements.
ARP
arp dynamicrenew
arp dynamicrenew
Changed default state from
enabled to disabled.
ARP
show arp
show arp
Changed the behavior so that all
entries are displayed when the
command is used without any
keywords.
Made the command available in
User EXEC mode.
Audit
show logging
show logging
This command is used to display
all logging information, including
auditing status.
Banner
show running-config
show running-config
This command output has been
enhanced to show banner
configuration.
Denial of
Service
dos-control icmp [size]
dos-control icmp [size]
Maximum ICMP packet size.
(Range 0-16376). If size is
unspecified, the value is 512.
Ethernet
Configuration
flowcontrol
flowcontrol
Changed the default
configuration from disabled to
enabled.
IP Routing
show ip route
show ip route
The command displays the
default gateway associated with
the route.
IPv6 Routing
show ipv6 route
show ipv6 route
The command displays the
default gateway associated with
the route.
April 6, 2011
Page 5
Dell PowerConnect™ Firmware CLI Transition Guide
Feature
Previous Implementation
Dell™ PowerConnect 4.x
Implementation
Comments
IPv6 Routing
show ipv6 route summary
[all]
show ipv6 route summary
[best]
Use best to display the count
summary for only best routes.
IP Routing
show ip interface
show ip interface
The output of the command is
updated to indicate how each IP
address was assigned.
IPv6 Routing
show ipv6 interface
show ipv6 interface
The output of the command is
updated to include the method
of assignment for each IPv6
address that is either autoconfigured or leased from a
DHCP server.
IP Routing
show ip route
show ip route
Displays the IPv4 address of the
default gateway.
IPv6 Routing
show ipv6 route
show ipv6 route
Displays the IPv6 address of the
default gateway, similar to show
ip route.
IP6 Routing
show ip route preferences
show ip route preferences
The user can configure a global
default gateway (ip defaultgateway), creating a default
route with a preference of 253.
The command output is updated
to list the new preference value
and the preference of default
routes learned from a DHCP
server.
Spanning Tree
spanning-tree mst instanceid priority priority
spanning-tree mst instanceid priority priority
Changed the instance-id range to
1-4094.
Stack Firmware
Synchronization
(SFS)
SDM Templates
show
show
show
show
show
show switch [chassis-mgmt |
stack-member-number |
stack-ports [counters | diag]
| stack-standby]
Modified the show switch
command to show the Switch
Firmware Synchronization (SFS)
status.
The show switch command can
display a new value, SDM
Mismatch, in the Switch Status
field, indicating that the unit
joined the stack, but is running a
different SDM template than the
management unit.
Syslog
logging file level
logging file [severity-levelnumber | type]
Made severity-level optional,
with a default value of error.
Note that persistent logging is
disabled by default.
April 6, 2011
switch [unit]
stack-port
stack-port counters
stack-port diag
stack-standby
Page 6
Dell PowerConnect™ Firmware CLI Transition Guide
Feature
Previous Implementation
Dell™ PowerConnect 4.x
Implementation
Comments
User Interface
Exit
Exit
In User EXEC mode, this
command behaves identically
with the quit command, closing
an active terminal session by
logging off the switch.
Virtual Router
Redundancy
Protocol (VRRP)
Ip vrrp
Ip vrrp mode
vrrp group ip ip-address
[secondary]
no vrrp group ip ip-address
vlan secondary
Use the no form of the command
to remove the secondary IP
address. It is not possible to
remove the primary ip address
once assigned. Remove the VRRP
group instead.
April 6, 2011
Page 7
Dell PowerConnect™ Firmware CLI Transition Guide
Updated Commands – Command Mode Modifications
Feature
Previous Implementation
Dell™ PowerConnect 4.x
Implementation
Comments
ARP
arp timeout seconds
arp timeout seconds
In the revised implementation,
the command is supported in both
Global Configuration Mode and
Interface Configuration Mode,
while previous implementation
supported only Global
Configuration Mode.
Banner
banner motd
banner motd <message>
The command mode was changed
from Privileged EXEC to Global
Configuration.
DHCP
Snooping
show ip dhcp snooping
show ip dhcp snooping
The command mode was changed
from Privileged EXEC to User
EXEC and Privileged EXEC.
DHCP
Snooping
show ip dhcp snooping
database
show ip dhcp snooping
database
The command mode was changed
from Privileged EXEC to User
EXEC and Privileged EXEC.
DHCP
Snooping
show ip dhcp snooping
statistics
show ip dhcp snooping
statistics
The command mode was changed
from Privileged EXEC to User
EXEC and Privileged EXEC.
Ethernet
Configuration
interface range ethernet
{port-range | all}
Interface range {portrange|port-type all}
It is no longer necessary to exit
Interface Configuration mode to
execute this command.
IGMP
Snooping
ip igmp snooping
ip igmp snooping vlan vlan-id
In Dell™ PowerConnect, the
command was modified from
VLAN Interface Configuration
Mode command to Global
Configuration Mode command
that includes the VLAN ID as a
parameter.
IGMP
Snooping
ip igmp snooping leave-timeout [time-out|immediateleave]
ip igmp snooping leave-timeout [time-out|immediateleave]
Changed the leave-time-out range
to 1-3174 seconds.
IP Addressing
ip address
n/a
There is no longer an ip address
command in Global Config mode
due to the deprecation of support
for the management interface
(i.e., network port).
IP Routing
show ip protocols
show ip protocols
The command mode was changed
from Privileged EXEC to Privileged
EXEC and User EXEC.
IP Routing
show ip route summary [all]
show ip route summary [best]
The command mode was changed
from Privileged EXEC to Privileged
EXEC and User EXEC.
April 6, 2011
Page 8
Dell PowerConnect™ Firmware CLI Transition Guide
Feature
Previous Implementation
Dell™ PowerConnect 4.x
Implementation
Comments
IPv6 Routing
show ipv6 interface {brief|
loopback loopback-id |
tunnel tunnel-id | vlan vlanid [prefix]}
show ipv6 interface [brief]
[loopback loopback-id |
tunnel tunnel-id | vlan vlan-id
[prefix]]
The command mode was changed
from Privileged EXEC to Privileged
EXEC and User EXEC.
IPv6 Routing
show ipv6 neighbors
show ipv6 neighbors
The command mode was changed
from Privileged EXEC to Privileged
EXEC and User EXEC.
IPv6 Routing
show ipv6 route summary
[all]
show ipv6 route summary
[best]
The command mode was changed
from Privileged EXEC to Privileged
EXEC and User EXEC.
Management
Interfaces
ipv6 address dhcp
ipv6 address dhcp
Added command modes Interface
(Loopback, Port-Channel)
Configuration.
configure terminal
Terminal is now accepted as an
optional parameter on the
configure command.
Mode
Commands
Tunnel
Interface
tunnel destination ipv4addr
tunnel destination ip-address
Added Tunnel Interface
Configuration.
VLAN
name string (VLAN
Configuration)
name <vlan-name>
Moved the command from
Interface Configuration mode to
VLAN Configuration mode.
April 6, 2011
Page 9
Dell PowerConnect™ Firmware CLI Transition Guide
Updated Commands – Syntax Modifications
Feature
Previous Implementation
Dell™ PowerConnect 4.x Implementation
802.1x
dot1x timeout re-authperiod seconds
dot1x timeout reauth-period seconds
802.1x
dot1x re-authentication
dot1x reauthentication
802.1x
dot1x multiple-hosts
dot1x host-mode {single-host | multi-host}
802.1x
show dot1x [{ethernet interface | statistics
ethernet interface}]
show dot1x [interface interface-id [statistics]]
802.1x
show dot1x clients {all|ethernet interface}
show dot1x clients {<interface-id> | all}
802.1x
Enhancements
show vlan [id vlan-id|name vlan-name]
show vlan [id vlan-id|name vlan-name]
AAA
username name password password [level
level] [encrypted]
username name password password [privilege
level] [encrypted]
AAA
username name passwd password [level
level] [encrypted] [override-complexitycheck]
username name password password [privilege
level] [encrypted]
Address Table
clear bridge
clear mac-addresses {ethernet interface |
port-channel port-channel-number}
clear mac address-table dynamic [address
mac-addr | interface interface-id | vlan vlanid]
ARP
arp ip-address mac-address
arp ip-address hardware-address
ARP
show ip arp inspection ethernet [ interfaces
[interface-id] ]
show ip arp inspection [interfaces [interfaceid] | statistics [vlan vlan-range] | vlan vlanrange]
Captive Portal
show captive-portal interface interface
client status
show captive-portal interface {gigabitethernet
unit/slot/port | tengigabitethernet
unit/slot/port} client status
Configuration
and Image File
boot system [image1|image2]
boot system [unit-id] [image1|image2]
DHCP Snooping
ip dhcp snooping limit {none | rate pps
[burst interval seconds]}
ip dhcp snooping limit {none | rate rate [burst
interval seconds ]}
DHCP Snooping
show ip dhcp snooping binding [ { static |
dynamic } ] [ interface port ] [ vlan vlan-id ]
show ip dhcp snooping binding [{ static |
dynamic } ] [ interface interface-id ] [ vlan
vlan-id ]
DHCPv6
domain-name dns-domain-name
domain-name domain
DHCPv6
prefix-delegation ipv6-prefix/prefix-length
client-DUID [name hostname] [valid-lifetime
{valid-lifetime | infinite}] [preferredlifetime {preferred-lifetime | infinite}]
prefix-delegation ipv6-prefix/prefix-length
client-DUID [name hostname] [valid-lifetime
{valid-lifetime | infinite}] [preferred-lifetime
{preferred-lifetime | infinite}]
DHCPv6
show ipv6 dhcp binding [ipv6 addr]
show ipv6 dhcp binding [ipv6-address]
DHCPv6
show ipv6 dhcp interface {tunnel tunnel-id |
vlan vlan-id} [statistics]
show ipv6 dhcp interface [interface-id]
{statistics}
DHCPv6
show ipv6 dhcp pool pool-name
show ipv6 dhcp pool [poolname]
April 6, 2011
Page 10
Dell PowerConnect™ Firmware CLI Transition Guide
DNS Client
Enhancements
The following commands are modified to
allow spaces in host names.
Global Configuration Mode Commands:
radius-server host [ acct | auth ] { ip–address |
hostname }
tacacs-server host {ip-address|hostname}
sntp server {ip-address | ipv6-address |
hostname}
snmp-server v3-host {ip-address | hostname}
username {traps | informs} [noauth | auth |
priv] [timeout seconds] [retries retries]
[udpport port] [filter filtername]
logging {ip-address | hostname}
hostname name
DNS Client
Enhancements
The following commands are modified to
allow spaces in host names.
Privileged EXEC Mode Commands:
show hosts [<hostname>]
show radius-servers statistics [ accounting |
authentication ] { ipaddress | hostname | name
servername}
ping ipv6 {ip-address | hostname} [size size]
traceroute ipv6 {ip-address | hostname} [port ]
copy source-url destination-url
ping [ ip | ipv6 ] ipaddress | hostname [ repeat
count ] [ timeout interval ] [ size size ]
traceroute [ ip | ipv6 ] ipaddress | hostname [
initTtl initTtl ] [ maxTtl maxTtl ] [ maxFail
maxFail ] [ interval interval ] [ count count ] [
port port ] [ size size ]
DNS Client
Enhancements
The following command is modified to allow
spaces in host names.
IPv6 DHCP Pool Configuration mode commands:
prefix-delegation ipv6-prefix/prefix-length
client-DUID [name hostname] [valid-lifetime
{valid-lifetime | infinite}] [preferred-lifetime
{preferred-lifetime | infinite}]
Ethernet
Configuration
speed [10 | 100 ]
speed {10 | 100 | 1000 | 10000 | auto [10 |
100 | 1000 | 10000]}
Ethernet
Configuration
duplex {half| full}
duplex {auto | full | half}
File System
copy <source><dest>
copy <source-url><destination-url>
IGMP
ip igmp last-member-query-count count
ip igmp last-member-query-count Imqc
April 6, 2011
Page 11
Dell PowerConnect™ Firmware CLI Transition Guide
IGMP
ip igmp query-max-response-time
tenthsofseconds
ip igmp query-max-response-time seconds
IGMP
show ip igmp interface vlan vlan-id
show ip igmp interface [interface-type
interface-number]
IGMP
show ip igmp groups interface vlan vlanid
[detail]
show ip igmp groups [interface-type interfacenumber] [detail]
IGMP
show ip igmp interface membership
groupaddr [detail]
show ip igmp membership [groupaddr] [detail]
IGMP Snooping
Querier
ip igmp snooping querier [vlan-id [address
ipv4_address]]
ip igmp snooping querier [vlan vlan-id] [address
ip-address]
IGMP Snooping
Querier
ip igmp snooping querier query-interval
seconds
ip igmp snooping querier query-interval
interval-count
IGMP Snooping
Querier
ip igmp snooping querier version number
ip igmp snooping querier version version
IGMP Snooping
Querier
show ip igmp snooping querier [{detail |
vlan vlan-id}]
show ip igmp snooping querier [detail | vlan
vlan-id]
Interface
Configuration
interface ethernet interface
interface range ethernet { port-range | all }
interface port-channel port-channel-number
interface interface-id
interface range {port-range-list | all}
IP Addressing
ip address ip-address {subnet-mask | prefixlength} [secondary]
ip address {ip-address {mask | prefix-length} |
dhcp}
IP Routing
ip mtu integer
ip mtu [bytes]
IP Routing
show ip interface [vlan vlan-id | loopback
loopback-id]
show ip interface [type number]
IPv6 Routing
ipv6 mtu mtu
ipv6 mtu bytes
IPv6 Routing
ipv6 nd dad attempts attempts
ipv6 nd dad attempts value
IPv6 Routing
ipv6 nd prefix prefix/prefix-length [{validlifetime| infinite} {preferred-lifetime|
infinite}] [no-autoconfig] [off-link]
ipv6 nd prefix <ipv6-prefix/prefix-length>
[{valid-lifetime| infinite} {preferred-lifetime|
infinite}] [no-autoconfig] [off-link]
IPv6 Routing
ipv6 route ipv6-prefix /prefix-length [Null |
interface {tunnel tunnel-id | vlan vlan-id}]
nexthop-address [ preference ]
ipv6 route <distance>
ipv6 route <ipv6-prefix/prefix-length> { ipv6address | <interface-type> ipv6-address }
[preference]
IPv6 Routing
show ipv6 interface {brief| loopback
loopback-id | tunnel tunnel-id | vlan vlan-id
[prefix]}
show ipv6 interface [brief] [loopback loopbackid | tunnel tunnel-id | vlan vlan-id [prefix]]
iSCSI
iscsi cos {vpt vpt | dscp dscp } [remark]
iscsi cos {enable | disable | vpt vpt | dscp dscp
[remark]}
Multicast
ip mroute source-address source-mask rpfaddress preference
ip mroute <source-address> <mask> <rpfaddress> <preference>
OSPF
area area-id nssa (Router OSPF)
area <area-id> nssa [no-redistribution]
[default-information-originate [metric metricvalue] [metric-type metric-type-value]] [nosummary] [translator-role role] [translatorstab-intv interval]
April 6, 2011
Page 12
Dell PowerConnect™ Firmware CLI Transition Guide
OSPF
area area-id virtual-link neighbor-id
area area-id virtual-link neighbor-id deadinterval seconds
area area-id virtual-link neighbor-id hellointerval seconds
area area-id virtual-link neighbor-id
retransmit-interval seconds
area area-id virtual-link neighbor-id
transmit-delay seconds
area <area-id> virtual-link <router-id> [hellointerval seconds] [retransmit-interval seconds]
[transmit-delay seconds] [dead-interval
seconds]
OSPF
default-information originate [always]
[metric integer] [metric-type {1 | 2}]
default-information originate [always] [metric
metric-value] [metric-type type-value]
OSPF
default-metric integer
default-metric metric-value
OSPF
distance ospf {external | inter-area | intraarea } distance
distance ospf {[intra-area dist1] [inter-area
dist2] [external dist3]}
OSPF
distribute-list accesslistname out {rip |
static | connected}
distribute-list name out {rip | static |
connected}
OSPF
ip ospf cost integer
ip ospf cost interface-cost
OSPF
ip ospf priority integer
ip ospf priority number-value
OSPF
redistribute {rip | static | connected}
[metric integer] [metric-type {1 | 2}] [tag
integer][subnets]
redistribute protocol [metric metric-value]
[metric-type type-value] [tag tag-value]
[subnets]
OSPF
show ip ospf
show ip ospf
OSPF
show ip ospf interface {vlan vlan-id |
loopback loopback-id}
show ip ospf interface [interface-type
interface-number]
OSPF
show ip ospf neighbor [interface vlan vlanid] [ip-address]
show ip ospf neighbor [interface-type
interface-number] [neighbor-id]
OSPF
show ip ospf statistics
show ip ospf statistics
OSPF
show ip ospf virtual-link area-id neighbor-id
show ip ospf virtual-links [area-id neighbor-id]
OSPF
show ip ospf virtual-link brief
show ip ospf virtual-links brief
OSPFv3
area areaid default-cost cost
area <area-id> default-cost <cost>
OSPFv3
area area-id nssa
area <area-id> nssa [no-redistribution]
[default-information-originate [metric metricvalue] [metric-type metric-type-value]] [nosummary] [translator-role role] [translatorstab-intv interval]
OSPFv3
area area-id range ipv6-prefix/prefix-length
{summarylink | nssaexternallink} [advertise
| not-advertise]
area <area-id> range ipv6-prefix/prefix-length
{summarylink | nssaexternallink} [advertise |
not-advertise]
OSPFv3
area areaid stub
area areaid stub no-summary
area <area-id> stub [no-summary]
April 6, 2011
Page 13
Dell PowerConnect™ Firmware CLI Transition Guide
OSPFv3
area area-id virtual-link neighbor-id
area area-id virtual-link neighbor-id deadinterval seconds
area area-id virtual-link neighbor-id hellointerval seconds
area area-id virtual-link neighbor-id
retransmit-interval seconds
area area-id virtual-link neighbor-id
transmit-delay seconds
area area-id virtual-link router-id [hellointerval seconds] [retransmit-interval seconds]
[transmit-delay seconds] [dead-interval
seconds]
OSPFv3
default-information originate [always]
[metric integer] [metric-type {1 | 2}]
default-information originate [always] [metric
metric-value] [metric-type type-value]
OSPFv3
default-metric integer
default-metric metric-value
OSPFv3
ipv6 ospf cost cost
ipv6 ospf cost <interface-cost>
OSPFv3
ipv6 ospf priority priority
ipv6 ospf priority <number-value>
OSPFv3
show ipv6 ospf
show ipv6 ospf area areaid
show ipv6 ospf [area-id]
OSPFv3
show ipv6 ospf [areaid] database [{external
| inter-area {prefix | router} | link |
network | nssaexternal | prefix | router |
unknown [area | as | link]}] [lsid] [advrouter [rtrid] | self-originate]
show ipv6 ospf [area-id] database [{external |
inter-area {prefix | router} | link | network |
nssaexternal | prefix | router | unknown [area
| as | link]}] [link-state-id] [adv-router [routerid] | self-originate]
OSPFv3
show ipv6 ospf database database-summary
show ipv6 ospf database database-summary
OSPFv3
show ipv6 ospf interface {vlan vlan-id|
tunnel tunnel-id | loopback loopback-id}
show ipv6 ospf interface [interface-type
interface-number]
OSPFv3
show ipv6 ospf neighbor [ interface { vlan
vlan-id | tunnel tunnel-id } ] [ ip-address ]
show ipv6 ospf [process-id] [area-id] neighbor
[interface-type interface-number] [neighborid] [detail]
OSPFv3
show ipv6 ospf virtual-link {areaid neighbor
| brief}
show ipv6 ospf virtual-links [area-id neighbor-id
| brief]
Password
Management
passwords aging age
passwords aging <1-365>
Password
Management
passwords history historylength
passwords history <0-10>
Password
Management
passwords lock-out attempts
passwords lock-out <1-5>
Password
Management
passwords min-length <length>
passwords min-length <8-64>
Password
Management
show passwords configuration
show passwords configuration
Password
Management
password
password (User EXEC)
Password
Management
show users accounts [long]
show users accounts
Port Monitor
monitor session session-id {source interface
src-interface [rx | tx] | destination
interface dst-interface}
monitor session session_number {source
interface interface-id [rx | tx] | destination
interface interface-id}
Port Monitor
show monitor session session-id
show monitor session session_number
April 6, 2011
Page 14
Dell PowerConnect™ Firmware CLI Transition Guide
Power Over
Ethernet
power inline usage-threshold <threshold>
power inline usage-threshold <threshold>
Power Over
Ethernet
priority { critical | high | low }
power inline priority { critical | high | medium
| low }
Power Over
Ethernet
show power inline [detailed]
show power inline [<interface-id>] [detailed]
QoS
show service-policy
show service-policy {in|out}
RADIUS
radius-server deadtime deadtime
radius-server deadtime deadtime
RADIUS
radius-server host [ acct | auth ] {ipaddress
| hostname}
radius-server host [ acct | auth ] { ipaddress |
hostname }
RIP
default-metric integer
default-metric metric-value
RMON
rmon alarm index variable interval
rthreshold fthreshold revent fevent [type
type] [startup direction] [owner name]
rmon alarm number variable interval {delta |
absolute} rising-threshold value [eventnumber] falling-threshold value [eventnumber] [owner string] [startup direction]
RMON
rmon event index type [community text]
[description text ] [owner name]
rmon event number [log] [trap community]
[description string] [owner string]
Router
Discovery
Protocol
This command was previously documented
as seven separate commands:
ip irdp
ip irdp multicast
ip irdp holdtime integer
ip irdp maxadvertinterval seconds
ip irdp [multicast | holdtime seconds |
maxadvertinterval seconds | minadvertinterval
seconds | preference number | address
address]
ip irdp minadvertinterval seconds
ip irdp preference number
ip irdp address ip-address
Router
Discovery
Protocol
show ip irdp {vlan vlan-id|all}
show ip irdp [vlan vlan-id]
SNMP
show trapflags [ospf|ospfv3]
show trapflags [ acl | auto-copy-sw | captiveportal cp-type | dot1q | dvrmp | link |
maclock | multiple-users | ospf ospftype |
ospfv3 ospfv3type | pim | poe | snmp
authentication | spanning-tree | stack | vrrp ]
SNMP
snmp-server community community-string
{ro | rw | su} [ipaddress ipaddress] [view
viewname]
snmp-server community string [ro | rw | su]
[view view-name] [ipaddress ipaddress]
SNMP
snmp-server enable traps
snmp-server enable traps authentication
power inline traps
boot auto-copy-sw trap
ip dvmrp trapflags
ip pim trapflags
port security trap
trapflags (ip ospf mode)
trapflags (ipv6 ospf mode)
port security trap
snmp-server enable traps [acl | all | autocopy-sw | captive-portal cp-type | dot1q |
dvrmp | link | maclock | multiple-users | ospf
ospftype | ospfv3 ospfv3type | pim | poe |
snmp authentication | spanning-tree | stack |
vrrp ]
April 6, 2011
Page 15
Dell PowerConnect™ Firmware CLI Transition Guide
SNMP
snmp-server host {ip-address | hostname}
community {traps {v1 | v2} | informs
[timeout seconds] [retries retries]} [udpport
port] [filter filtername]
snmp-server host host-addr [informs [timeout
seconds] [retries retries] | traps version {1 | 2
}]] community-string [udp-port port] [filter
filtername]
SNMP
snmp-server v3-host {ip-address|hostname}
username {traps|informs}[noauth|auth|priv]
[timeout seconds] [retries retries] [udpport
port] [filter filtername]
snmp-server v3-host {ip-address|hostname}
username {traps|informs}[noauth|auth|priv]
[timeout seconds] [retries retries] [udpport
port] [filter filtername]
Spanning Tree
revision <value>
revision <version>
Spanning Tree
spanning-tree cost cost
spanning-tree cost cost
Spanning Tree
spanning-tree mode {stp | rstp |mstp}
spanning-tree mode {stp | rstp | mst}
Spanning Tree
spanning-tree mst instance-id cost cost
spanning-tree mst instance-id cost cost
Spanning Tree
spanning-tree portfast
spanning-tree portfast
Syslog
logging buffered level
logging buffered [severity- level]
Syslog
logging buffered level
logging buffered [severity- level]
Syslog
logging file level
logging file [severity-level-number | type]
System
Management
reload [unit]
reload [stack-member-number]
System
Management
telnet {ip-address | hostname} [port]
[keyword1......]
telnet {ip-address | hostname} [port]
[keyword1......]
Time-Based
ACLs
IP Standard ACL:
access-list <name>
access-list <name> {deny | permit} {every |
<srcip> <srcmask>} [log] [time-range <timerange-name>] [assignqueue <queue-id>]
[{mirror | redirect} <interface-id>]
IP Extended ACL:
access-list <name> {deny | permit} {every |
{{icmp | igmp | ip | tcp | udp | <number>}
<srcip> <srcmask>[{eq {<portkey> | <0-65535>}
<dstip> <dstmask>
[{eq {<portkey>| <0-65535>}] [precedence
<precedence> | tos <tos> <tosmask> |
dscp <dscp>] [log] [time-range <time-rangename>] [assign-queue <queue-id>] [{mirror |
redirect} <interface-id>]
Time-Based
ACLs
April 6, 2011
{deny|permit} {srcmac srcmacmask | any}
{dstmac dstmacmask | any|bpdu}
[{ethertypekey|0x0600- 0xFFFF}][ vlan eq
0-4095] [cos 0-7] [secondary-vlan eq 04095][secondary-cos 0-7][log] [assign-queue
queue-id] [{mirror | redirect} interface]
{deny|permit} {<srcmac> | any} {<dstmac> |
any} [<ethertypekey> | <0x0600- 0xFFFF>]
vlan {eq <0-4095>}] [cos <0-7>] [[log] [timerange <time-range-name>] [assign-queue
<queue-id>] [{mirror | redirect} <interface-id>]
Page 16
Dell PowerConnect™ Firmware CLI Transition Guide
Time-Based
ACLs
{deny | permit} {every | {{icmp |igmp| ipv6
| tcp | udp | number} {any |
sourceipv6prefix/prefixlength} [eq {portkey
|portvalue}] {any |
destinationipv6prefix/prefixlength} [eq
{portkey | portvalue}] [flow-label value]
[dscp dscp]}} [log][assign-queue queue-id]
[{mirror | redirect} interface]
{deny | permit} {every | {{icmpv6 | ipv6 | tcp
| udp | protocolnumber} {any |
sourceipv6prefix/prefixlength} [eq
{portnumber | portkey}] {any |
destinationipv6prefix/prefixlength}] [eq
{portnumber | portkey}] [flow-label flow-labelvalue] [dscp dscp-value]} [assign-queue queueid] [log] [{mirror | redirect} interface-id]
[time-range time-range-name]
Time-Based
ACLs
show ipv6 access-lists [name]
show ipv6 access-lists [name]
Time-Based
ACLs
show mac access-list name
show mac access-list name
Tunnel
Interface
tunnel destination ipv4addr
tunnel destination ip-address
Tunnel
Interface
tunnel source {ipv4addr | vlan vlan-id}
tunnel source { ip-address | interface-type
interface-number
User Manager
Enhancements
aaa authentication dot1x default method1
aaa authentication dot1x default { radius | ias
| none }
Virtual Router
Redundancy
Protocol (VRRP)
show ip vrrp interface { brief | [stats] vlan
vlan-id vr-id }
show vrrp interface [ brief | vlan <vlan-id>
{stats} ]
Virtual Router
Redundancy
Protocol (VRRP)
show ip vrrp
show vrrp [brief | group]
VLAN
dvlan-tunnel ethertype
{802.1Q|vman|custom 0-65535}
dvlan-tunnel ethertype {802.1Q | vman |
custom 0-65535 [primary-tpid] }
VLAN
switchport mode {access | trunk |
general|dot1q tunnel }
switchport mode {access | trunk | general }
VLAN
name string (VLAN Configuration)
name vlan-name
Corrected
parameters to
match CLI for
the following
commands:
April 6, 2011
mac address-table multicast forbidden address
mac address-table multicast static
mac address-table static
interface (removed the Interface Ethernet
command and consolidated it into the interface
command
interface range
show dot1x ethernet has been changed to show
dot1x interface {gigabitethernet |
tengigabitethernet)
arp (global) -- removed second (redundant)
instance -- it did not match CLI.
deny/permit (ipv6 acl mode)
show lldp med local-device detail -- Added the
word detail to command name, changed
description.
Page 17
Dell PowerConnect™ Firmware CLI Transition Guide
Deprecated Commands
Feature
Previous Implementation
Dell™ PowerConnect 4.x Implementation
802.1x
dot1x system-auth-control
This command is changed to dot1x system-auth-control
monitor.
Address
Table
bridge address
This command is changed to mac address-table static.
Address
Table
bridge aging-table
This command is changed to mac address-table agingtime.
Address
Table
bridge multicast address
This command is changed to mac address-table
multicast static.
Address
Table
bridge multicast filtering
This command is changed to mac address-table
multicast filtering.
Address
Table
bridge multicast forbidden
address
This command is changed to mac address-table
multicast forbidden address.
Address
Table
bridge multicast forbidden
forward-unregistered
This command is changed to mac address-table
multicast forbidden forward-unregistered.
Address
Table
bridge multicast forward-all
This command is changed to mac address-table
multicast forward-all.
Address
Table
bridge multicast forwardunregistered
This command is changed to mac address-table
multicast forward-unregistered.
Address
Table
clear bridge
This command is changed to clear mac address-table.
Address
Table
mac address-table static
drop
This command has been removed. Refer to the Address
Table Commands section in the CLI Reference Guide.
Address
Table
port security trap
This command is deprecated by the snmp-server enable
traps maclock command.
Address
Table
show bridge address-table
This command is changed to show mac address-table.
Address
Table
show bridge address-table
count [vlan vlan | ethernet
interface-number | portchannel port-channelnumber]
This command is changed to show mac address-table
count.
Address
Table
show bridge address-table
[vlan vlan] [ethernet
interface | port-channel
port-channel-number]
This command is changed to show mac address-table
interface and show mac address-table vlan.
Address
Table
show bridge address-table
static
This command is changed to show mac address-table
static.
ARP
clear counters ip arp
inspection
clear ip arp inspection statistics
ARP
show ip arp inspection
ethernet
show ip arp inspection
April 6, 2011
Page 18
Dell PowerConnect™ Firmware CLI Transition Guide
Feature
Previous Implementation
Dell™ PowerConnect 4.x Implementation
Bridging
bridge address
Interface Configuration mode
Rationale: The following parameters have been
deprecated:
delete-on-reset
delete-on-timeout
secure
DHCP and
BOOTP Relay
bootpdhcprelay
cidridoptmode
This command is changed to ip dhcp relay information
option.
DHCP and
BOOTP Relay
show bootpdhcprelay
This command is changed to show ip dhcp relay
command.
DHCPv6
ipv6 dhcp relay-agent-infoopt
This command is deprecated. Refer to the DHCPv6
Commands section in the CLI REFERENCE GUIDE.
DHCPv6
ipv6 dhcp relay-agent-inforemote-id-subopt
This command is deprecated. Refer to the DHCPv6
Commands section in the CLI REFERENCE GUIDE.
DVMRP
ip dvmrp trapflags
The command is deprecated by the snmp-server enable
traps dvmrp command.
Ethernet
Configuration
Interface range ethernet
This command is changed to interface range.
Ethernet
Configuration
negotiation
This command is deprecated. Negotiation is now
configured using the speed or duplex commands. Refer
to the Ethernet Configuration Commands section in the
CLI REFERENCE GUIDE.
IGMP
show ip igmp interface
membership groupaddr
[detail]
This command is changed to show ip igmp membership
[groupaddr] [detail] command.
IP Addressing
ipv6 gateway
This command is removed. Refer to the IP Addressing
Commands section in the CLI REFERENCE GUIDE.
IP Addressing
show ip interface
management
This command is removed. Refer to the IP Addressing
Commands section in the CLI REFERENCE GUIDE.
IP Routing
routing / no switchport
This command is removed. Refer to the IP Routing
Commands section in the CLI REFERENCE GUIDE.
IP Routing
show ip stats
This command is changed to show ip traffic.
IPv6
Multicast
ipv6 pimsm and ipv6 pimdm
These commands are replaced by the ipv6 pim
command.
IPv6
Multicast
ipv6 pimsm
This command is replaced by ipv6 pim sparse (Global
config) and ipv6 pim dense commands.
IPv6
Multicast
ipv6 pimsm bsr-border
This command is replaced by ipv6 pim bsr-border.
IPv6
Multicast
ipv6 pimsm bsr-candidate
This command is replaced by ipv6 pim bsr-candidate.
IPv6
Multicast
ipv6 pimsm dr-priority
This command is replaced by ipv6 pim dr-priority.
IPv6
Multicast
ipv6 pimsm hello-interval
and ipv6 pimdm hellointerval
These commands are replaced by the ipv6 pim hellointerval command.
April 6, 2011
Page 19
Dell PowerConnect™ Firmware CLI Transition Guide
Feature
Previous Implementation
Dell™ PowerConnect 4.x Implementation
IPv6
Multicast
ipv6 pimsm join-pruneinterval
This command is replaced by the ipv6 pim join-pruneinterval command.
IPv6
Multicast
ipv6 pimsm registerthreshold
This command is replaced by the ipv6 pim register-ratelimit command.
IPv6
Multicast
ipv6 pimsm rp-address
This command is replaced by the ipv6 pim rp-address
command.
IPv6
Multicast
ipv6 pimsm rp-candidate
This command is replaced by the ipv6 pim rp-candidate
command.
IPv6
Multicast
ipv6 pimsm spt-threshold
This command is replaced by the ipv6 pim spt-threshold
command.
IPv6
Multicast
ipv6 pimsm ssm
This command is replaced by the ipv6 pim ssm
command.
IPv6
Multicast
show ipv6 pimdm
This command is removed. Refer to the IPv6 Multicast
Commands section in the CLI REFERENCE GUIDE.
IPv6
Multicast
show ipv6 pimsm interface
and show ipv6 pimdm
interface
These commands are replaced by the show ipv6 pim
interface command.
IPv6
Multicast
show ipv6 pimsm neighbor
and show ipv6 pimdm
neighbor
These commands are replaced by the show ipv6 pim
neighbor command.
IPv6
Multicast
show ipv6 pimsm rp mapping
This command is replaced by the show ipv6 pim rp
mapping command.
IPv6
Multicast
show ipv6 pimsm rphash
This command is replaced by the show ipv6 pim bsrrouter command.
IPv6 Routing
Multicast
ipv6 forwarding
This command is deprecated. Refer to the IPv6 Routing
Commands section in the CLI REFERENCE GUIDE.
ip pim-trapflags
This command is deprecated by the snmp-server enable
traps pim command.
Multicast
ip pimsm
This command is replaced by the ip pim dense and ip
pim sparse commands.
Multicast
ip pimsm bsr-border
This command is replaced by the ip pim bsr-border
command.
Multicast
ip pimsm bsr-candidate
This command is replaced by the ip pim bsr-candidate
command.
Multicast
ip pimsm cbsrhaskmasklength
and ip pimsm cbsrpreference
These commands are replaced by the ip pim bsrcandidate command.
Multicast
ip pimsm dr-priority
This command is replaced by the ip pim hello-interval
command.
Multicast
ip pimsm join-prune-interval
This command is replaced by the ip pim join-pruneinterval command.
Multicast
ip pimsm register-threshold
This command is replaced by the ip pim register-ratelimit command.
Multicast
ip pimsm ssm
This command is replaced by the ip pim ssm command.
April 6, 2011
Page 20
Dell PowerConnect™ Firmware CLI Transition Guide
Feature
Previous Implementation
Dell™ PowerConnect 4.x Implementation
Multicast
ip pimsm spt-threshold
This command is replaced by the ip pim spt-threshold
and ip pim register-rate-limit commands.
Multicast
ip pimsm rp-address
This command is replaced by the ip pim rp-address
command.
Multicast
ip pimsm rp-candidate
This command is replaced by the ip pim bsr-border
command.
Multicast
show ip pimsm bsr
This command is replaced by the show ip pim bsr-router
command.
Multicast
show ip pimsm rphash
This command is replaced by the show ip pim rp hash
command.
Multicast
show ip pimsm rp mapping
This command is replaced by the show ip pim rp
mapping command.
Multicast
show ip mcast
This command is changed to show ip multicast.
Multicast
show ip mcast interface
This command is changed to show ip multicast
interface.
OSPF
1583compatibility
This command is changed to compatible rfc1583.
OSPFv3
Ipv6 ospf areaid
This command is changed to ipv6 ospf area.
PHY
Diagnostics
show copper-ports cablelength
This command is deprecated. Use the show copper-ports
tdr command to display the stored information
regarding cable lengths and the test copper-port tdr
command to perform a cable length test. Testing a port
brings the port down momentarily.
PIM-DM and
PIM-SM
ip pimsm and ip pimdm
These commands are replaced by the ip pim command.
PIM-DM and
PIM-SM
ip pimsm hello-interval and
ip pimdm hello-interval
These commands are replaced by the ip pim hellointerval command.
PIM-DM and
PIM-SM
show ip pimsm interface and
show ip pimdm interface
These commands are replaced by the show ip pim
interface command.
PIM-DM and
PIM-SM
show ip pimsm neighbor and
show ip pimdm neighbor
These commands are replaced by the show ip pim
neighbor command.
Power Over
Ethernet
power inline legacy
This command is deprecated by the power inline
detection command.
Power Over
Ethernet
power inline traps enable
This command is deprecated by the snmp-server enable
traps poe command.
Power Over
Ethernet
show poe-firmware-version
This command is deprecated by the show power inline
firmware-version command.
April 6, 2011
Page 21
Dell PowerConnect™ Firmware CLI Transition Guide
Feature
Previous Implementation
Dell™ PowerConnect 4.x Implementation
Power Over
Ethernet
trapflags (ip ospf mode)
This command is deprecated by the snmp-server enable
traps ospf command.
Power Over
Ethernet
trapflags (ipv6 ospf mode)
This command is deprecated by the snmp-server enable
traps ospfv3 command.
Power Over
Ethernet
ip pim trapflags
This command is deprecated by the snmp-server enable
traps pim command.
RADIUS
show radius-servers
This command is changed to show aaa servers.
RADIUS
show radius-servers statistics
This command is changed to show radius statistics.
RMON
show rmon-alarm table
This command is changed to show rmon alarms.
SNMP
show snmp groups
This command is changed to show snmp group.
SNMP
show snmp users
This command is changed to show snmp user.
SNMP
snmp-server traps enable
power inline
This command is deprecated. Use the poe keyword
command.
Syslog
logging facility
This command is deprecated. Refer to the Syslog
Commands section in the CLI REFERENCE GUIDE.
April 6, 2011
Page 22
Dell PowerConnect™ Firmware CLI Transition Guide
Feature
Previous Implementation
Dell™ PowerConnect 4.x Implementation
System
Management
switch priority
This command is deprecated. Refer to the System
Management Commands section in the CLI REFERENCE
GUIDE.
Ip dvmrp trapflags
This command is deprecated by the snmp-server enable
traps dvmrp command.
Virtual
Router
Redundancy
Protocol
(VRRP)
ip vrrp
ip vrrp ip
ip vrrp mode
These commands are replaced by the vrrp group ip ipaddress [secondary] command.
Web Server
ip https certificate
This command is changed to ip http secure-certificate.
Web Server
ip https port
This command is changed to ip http secure-port.
Web Server
ip https server
This command is changed to ip http secure-server.
Web Server
show ip http
This command is changed to show ip http server status.
Web Server
show ip https
This command is changed to show ip http server secure
status.
April 6, 2011
Page 23