Dell PP22L Laptop User Manual

OWNER’S MANUAL
PLASMA TV
Please read this manual carefully before operating your set and retain it
for future reference.
42PA4500
50PA4500
50PA4510
42PA4900
50PA4900
P/NO : MFL67468642 (1206-REV01)
50PA5500
60PA5500
50PA6500
60PA6500
60PA6550
42PA450C
50PA450C
50PA550C
60PA550C
www.lg.com
2
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Always comply with the following precautions to avoid dangerous situations and ensure peak performance
of your product.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE
PERSONNEL.
ENGLISH
ENG
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
the appliance.
Do not use this apparatus near water.
yy
Clean only with a dry cloth.
yy
Do not block any ventilation openings. Install
yy
in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such
yy
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
WARNING/CAUTION
- TO REDUCE THE RISK OF FIRE AND
ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
WARNING: This product contains chemicals
known to the State of California to cause cancer
and birth defects or other reproductive harm.
Wash hands after handling .
Do not defeat the safety purpose of the
yy
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet (Can differ by country).
IMPORTANT SAFETY INSTRUCTIONS
Protect the power cord from being walked on
yy
or pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
Only use attachments/accessories specified
yy
by the manufacturer.
Use only with a cart, stand, tripod, bracket,
yy
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Short-circuit
Breaker
Short-circuit
Breaker
Refer all servicing to qualified service
yy
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Short-circuit
Breaker
Do not stick metal objects or any other
yy
conductive material into the power cord. Do
not touch the end of the power cord while it
is plugged in.
Short-circuit
Power Supply
ENG
ENGLISH
Unplug this apparatus during lightning
yy
storms or when unused for long periods of
time.
Short-circuit
Breaker
Short-circuit
Breaker
Keep the packing anti-moisture material or
yy
vinyl packing out of the reach of children.
Anti-moisture material is harmful if
swallowed. If swallowed by mistake, force
the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can
cause suffocation. Keep it out of the reach of
children.
CAUTION concerning the Power Cord
yy
(Can differ by country):
It is recommended that appliances be
placed upon a dedicated circuit; that is, a
single outlet circuit which powers only that
appliance and has no additional outlets or
branch circuits. Check the specification page
of this owner’s manual to be certain. Do not
connect too many appliances to the same
AC power outlet as this could result in fire or
electric shock. Do not overload wall outlets.
Overloaded wall outlets, loose or damaged
Power
Supply
wall
outlets, extension cords, frayed power
Power Supply
cords, or damaged or cracked wire insulation
are dangerous. Any of these conditions could
result in electric shock or fire. Periodically
examine the cord of your appliance, and
Power
if Supply
its appearance indicates damage or
deterioration,
unplug it, discontinue use of
Power Supply
the appliance, and have the cord replaced
with an exact replacement part by an
authorized service. Protect the power cord
from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a
door, or walked upon. Pay particular attention
to plugs, wall outlets, and the point where
Power
Supply
the
cord exits the appliance. Do not move
the TV with the power cord plugged in. Do
not use a damaged or loose power cord. Be
sure do grasp the plug when unplugging the
power cord. Do not pull on the power cord
to unplug the TV.
3
4
IMPORTANT SAFETY INSTRUCTIONS
Warning - To reduce the risk of fire or
yy
electrical shock, do not expose this product
to rain, moisture or other liquids. Do not
touch the TV with wet hands. Do not install
this product near flammable objects such
as gasoline or candles, or expose the TV to
direct air conditioning.
Do not expose to dripping or splashing and
yy
do not place objects filled with liquids, such
as vases, cups, etc. on or over the apparatus
(e.g. on shelves above the unit).
Short-circuit
Breaker
Power Supply
ENGLISH
ENG
Grounding
yy
(Except for devices which are not grounded.)
Ensure that you connect the earth
Power ground
Supply
Short-circuit
wire to prevent possible
electric shock
Breaker
(i.e. a TV with a three-prong grounded AC
plug must be connected to a three-prong
grounded AC outlet). If grounding methods
are not possible, have a qualified electrician
install a separate circuit breaker. Do not try to
ground the unit by connecting it to telephone
wires, lightening rods, or gas pipes.
Short-circuit
Breaker
As long as this unit is connected to the AC
yy
wall outlet, it is not disconnected from the
AC power source even if the unit is turned
off.
Do not attempt to modify this product in any
yy
way without written authorization from LG
Electronics. Unauthorized modification could
void the user’s authority to operate this
product.
ANTENNAS Outdoor antenna grounding
yy
(Can differ by country):
If an outdoor antenna is installed, follow
the precautions below. An outdoor antenna
system should not be located in the vicinity
of overhead power lines or other electric light
or power circuits, or where it can come in
contact with such power lines or circuits as
death or serious injury can occur. Be sure the
antenna system is grounded so as to provide
some protection against voltage surges
and built-up static charges. Section 810 of
the National Electrical Code (NEC) in the
U.S.A. provides information with respect to
proper grounding of the mast and supporting
structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding
conductors, location of antenna discharge
unit, connection to grounding electrodes and
requirements for the grounding electrode.
Antenna grounding according to the National
Electrical Code, ANSI/NFPA 70
Power Supply
DISCONNECTING DEVICE FROM THE MAIN
yy
POWER
Mains plug is the disconnecting device. The
plug must remain readily operable.
Antenna Lead in Wire
Ground Clamp
Antenna Discharge Unit
(NEC Section 810-20)
Electric Service
Equipment
Grounding Conductor
(NEC Section 810-21)
Ground Clamp
NEC: National Electrical Code
Power Service Grounding
Electrode System
(NEC Art 250, Part H)
IMPORTANT SAFETY INSTRUCTIONS
Dot Defect
yy
The Plasma or LCD panel is a high
technology product with resolution of two
million to six million pixels. In a very few
cases, you could see fine dots on the screen
while you’re viewing the TV. Those dots
are deactivated pixels and do not affect the
performance and reliability of the TV.
Generated Sound
yy
“Cracking” noise: A cracking noise that
occurs when watching or turning off the TV
is generated by plastic thermal contraction
due to temperature and humidity. This noise
is common for products where thermal
deformation is required.
Electrical circuit humming/panel buzzing: A
low level noise is generated from a highspeed switching circuit, which supplies a
large amount of current to operate a product.
It varies depending on the product.
This generated sound does not affect the
performance and reliability of the product.
Take care not to touch the ventilation
yy
openings. When watching the TV for a long
period, the ventilation openings may become
hot. This does not affect the performance of
the product or cause defects in the product.
Preventing “Image burn” or “Burn-in” on your TV screen
Never touch this apparatus or antenna during
yy
a thunder or lightning storm.
When mounting a TV on the wall, make sure
yy
not to install the TV by hanging the power
and signal cables on the back of the TV.
Do not allow an impact shock or any objects
yy
to fall into the product, and do not drop
anything onto the screen.
If a fixed image displays on the TV screen for
yy
a long period of time, it will be imprinted and
become a permanent disfigurement on the
screen. This is “image burn” or “burn-in” and
not covered by the warranty.
If the aspect ratio of the TV is set to 4:3 for a
yy
long period of time, image burn may occur on
the letterboxed area of the screen.
Avoid displaying a fixed image on the TV screen
yy
for a long period of time (2 or more hours for
LCD, 1 or more hours for the Plasma TV) to
prevent image burn.
ENG
ENGLISH
Cleaning
yy
When cleaning, unplug the power cord and
wipe gently with a soft cloth to prevent
scratching. Do not spray water or other
liquids directly on the TV as electric shock
may occur. Do not clean with chemicals
such as alcohol, thinners or benzine.
Moving
yy
Make sure the product is turned off,
unplugged and all cables have been
removed. It may take 2 or more people to
carry larger TVs. Do not press or put stress
on the front panel of the TV.
Ventilation
yy
Install your TV where there is proper
ventilation. Do not install in a confined
space such as a bookcase. Do not cover the
product with cloth or other materials while
plugged. Do not install in excessively dusty
places.
If you smell smoke or other odors coming
yy
from the TV, unplug the power cord and
contact an authorized service center.
Do not press strongly upon the panel with a
yy
Supply
hand or a sharp objectShort-circuit
such as aPower
nail,
pencil
Breaker
or pen, or make a scratch on it.
Keep the product away from direct sunlight.
yy
5
6
IMPORTANT SAFETY INSTRUCTIONS
For USA and Canada
FCC NOTICE
ENGLISH
ENG
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the
equipment and the receiver.
- Connect the equipment to an outlet on
a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/
TV technician for help.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference and (2) this device must
accept any interference received, including
interference that may cause undesired
operation of the device.
Any changes or modifications in construction of
this device which are not expressly approved
by the party responsible for compliance
could void the user’s authority to operate the
equipment.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV
system installer’s attention to Article 820-40 of
the National Electric Code (U.S.A.). The code
provides guidelines for proper grounding and,
in particular, specifies that the cable ground
shall be connected to the grounding system of
the building, as close to the point of the cable
entry as practical.
LICENSES / OPEN SOURCE SOFTWARE NOTICE
7
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays
DivX video. Visit divx.com for more information and software tools to convert your
files into DivX video.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation
or its subsidiaries and are used under license.”
“Covered by one or more of the following U.S. patents:
7,295,673; 7,460,668; 7,515,710; 7,519,274”
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com .
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the
product.
ENG
ENGLISH
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered
in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your
registration code, locate the DivX VOD section in your device setup menu. Go to
vod.divx.com for more information on how to complete your registration.
8
TABLE OF CONTENTS
TABLE OF CONTENTS
ENGLISH
ENG
2
IMPORTANT SAFETY INSTRUCTIONS
28 REMOTE CONTROL
7
LICENSES
32
WATCHING TV
7
OPEN SOURCE SOFTWARE NOTICE
32
Turning the TV on for the first time
8
TABLE OF CONTENTS
9
Installation Procedure
9
ASSEMBLING AND PREPARING
9
11
13
14
15
15
16
16
17
18
Unpacking
Optional Extras
Parts and buttons
Lifting and moving the TV
Setting up the TV
-Attaching the stand
-Attaching the protection cover
-Tidying cables
-Mounting on a table
-Mounting on a wall
19
MAKING CONNECTIONS
19
20
Connecting to an antenna or cable
Connecting to a HD receiver, DVD, or VCR
player
-HDMI Connection
-DVI to HDMI Connection
-Component Connection
-Composite Connection
Connecting to a PC
-HDMI Connection, DVI to HDMI Connection or RGB Connection
Connecting to an Audio System
-Digital Optical Audio Connection
Connecting to a USB
20
21
22
23
24
24
26
26
27
33 Using the user guide
34 TROUBLESHOOTING
35
SPECIFICATIONS
38 MAINTENANCE
38
38
38
Cleaning Your TV
-Screen, frame, cabinet and stand
-Power cord
NOTE
Image shown may differ from your TV.
yy
Your TV’s OSD (On Screen Display) may
yy
differ slightly from that shown in this manual.
The available menus and options may differ
yy
from the input source or product model that
you are using.
New features may be added to this TV in the
yy
future.
ASSEMBLING AND PREPARING
9
Installation Procedure
1 Open the package and make sure all the accessories are included.
2 Attach the stand to the TV set.
3 Connect an external device to the TV set.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual
product and item.
For PA4500, PA4510, PA5500, PA6500, PA6550, PA450C, PA550C series
ENERGY AV MODE INPUT
TV
SAVING
1
2
3
4
5
6
7
8
9
LIST
0
FLASHBK
MARK
FAV
VOL
3D
CH
P
A
G
E
MUTE
Q.MENU
ENTER
BACK
EXIT
L/R SELECT
FREEZE
RATIO
Remote control,
Batteries (AAA)
(See p.28, p.30)
Owner’s manual
Power Cord
Stand Screws
4 EA, M4 x 30
(See p.15, p.16)
Stand Screws
3 EA, M5 x 16
(See p.15)
Power Cord holder
(See p.16)
Protection cover
(See p.16)
Ferrite core
(Depending on model)
(See p.12)
Cable holder
(See p.16)
Polishing cloth
(Depending on model)
Use this to remove dust from
the cabinet.
Stand Body
(See p.15)
Stand Base
(See p.15)
ENG
ENGLISH
MENU INFO
10
ASSEMBLING AND PREPARING
For PA4900 series
ENERGY AV MODE INPUT
TV
SAVING
1
2
3
4
5
6
7
8
9
LIST
0
FLASHBK
MARK
FAV
VOL
3D
CH
P
A
G
E
MUTE
MENU INFO
Q.MENU
ENTER
BACK
EXIT
L/R SELECT
FREEZE
RATIO
Owner’s manual,
CD manual (Included
Pentouch Software)
Power Cord
Stand Screws
4 EA, M4 x 30
(See p.15, p.16)
Stand Screws
3 EA, M5 x 16
(See p.15)
Polishing cloth
(Depending on model)
Use this to remove dust
from the cabinet.
Protection cover
(See p.16)
Cable holder
(See p.16)
Power Cord holder
(See p.16)
Ferrite core
(Depending on model)
(See p.12)
D-sub 15 pin signal cable
Eye-bolt & Wall bracket
2 EA
(See p.17)
Stand Body
(See p.15)
Stand Base
(See p.15)
Touch Pen
The number of touch pen
may differ depending on the
model.
ENGLISH
ENG
Remote control,
Batteries (AAA)
(See p.30)
Touch
Home
ASSEMBLING AND PREPARING
Tip
The number of tip may differ
depending on the model.
Touch Pen Dongle
11
Charging Cable
Cradle
Optional Extras
Touch
Home
AN-TP300
Touch Pen, Cradle
The number of touch pen and
tip may differ depending on the
model.
Compatibility
AN-TP300
Touch Pen, Cradle
PA4500
PA4510
PA4900
PA5500
PA6500
PA6550
PA450C PA550C
•
CAUTION
Do not use any unapproved items to ensure the safety and product life span.
yy
Any damages or injuries by using unapproved items are not covered by the warranty.
yy
In case of some model, the thin film on screen is a part of TV, So don’t take it off.
yy
ENG
ENGLISH
Optional extras can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
12
ASSEMBLING AND PREPARING
NOTE
The items supplied with your product may vary depending on the model.
yy
Product specifications or contents of this manual may be changed without prior notice due to
yy
upgrade of product functions.
How to use the ferrite core
yy
1 Use the ferrite core to reduce the electromagnetic interference in the PC audio cable.
Wind the PC audio cable on the ferrite core thrice. Place the ferrite core close to the TV.
10 mm(+ / - 5 mm)
[to an External device]
[to the TV]
[Figure 1]
(Gray)
[Cross Section of
Ferrite Core]
2 Use the ferrite core to reduce the electromagnetic interference in the power cable.
Wind the power cable on the ferrite core once. Place the ferrite core close to the TV and a wall
plug.
[to a wall plug]
[to the TV]
[Figure 2]
(Black)
[Cross Section of
Ferrite Core]
ENGLISH
ENG
3 Use the ferrite core to reduce the electromagnetic interference in the component cable.
Wind the component cable on the ferrite core once. Place the ferrite core close to the TV.
[to an External device]
[to the TV]
(Black)
[Cross Section of
Ferrite Core]
10 mm(+ / - 5 mm)
[Figure 3]
4 Use the ferrite core to reduce the electromagnetic interference in the component cable.
Place the ferrite core close to the TV.
[to an External device]
[to the TV]
10 mm(+ / - 5 mm)
[Figure 4]
-If there is one ferrite core, follow as shown in Figure 1.
-If there are three ferrite cores, follow as shown in Figures 1 and 2.
-If there are four ferrite cores, follow as shown in Figures 1, 2, 3 and 4.
(Black)
[Cross Section of
Ferrite Core]
ASSEMBLING AND PREPARING
13
Parts and buttons
Side Connection panel
USB IN
USB IN
Screen
IN 2
HDMI
input
Power indicator
IN 3
HDMI
input
IN 2
USB
input
Remote control and
intelligent1 sensors
(For PA4500,
PA4510,
PA450C series)
(For PA4900,
PA5500,
PA6500,
PA6550,
PA550C series)
Speakers
OK
Buttons
REMOTE
CONTROL
IN
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
COMPONENT IN
VIDEO
AV IN
L/MONO AUDIO R
RS-232C IN
(CONTROL & SERVICE)
OPTICAL
DIGITAL
AUDIO OUT
2
Y
PB
PR
L
ANTENNA/
CABLE IN
R
1
VIDEO
AUDIO
1
Button
IN
Rear Connection
panel
/ DVI
Description
/I
Turns the power on or off.
INPUT
Changes the input source.
SETTINGS
Accesses the main menus, or saves your input and exits the menus.
OK ⊙
Selects the highlighted menu option or confirms an input.
-
Adjusts the volume level.
+
v ^
Scrolls through the saved channels.
1 Adjusts the image quality and brightness based on the surrounding environment.
ENG
ENGLISH
INPUT SETTINGS
14
ASSEMBLING AND PREPARING
Lifting and moving the TV
When moving or lifting the TV, read the following
to prevent the TV from being scratched or
damaged and for safe transportation regardless of
its type and size.
When transporting a large TV, there should
yy
be at least 2 people.
When transporting the TV by hand, hold the
yy
TV as shown in the following illustration.
Caution
Avoid touching the screen at all times, as
yy
this may result in damage to the screen.
It is recommended to move the TV in the
yy
box or packing material that the TV originally
came in.
Before moving or lifting the TV, disconnect
yy
the power cord and all cables.
When holding the TV, the screen should face
yy
away from you to avoid damage.
ENGLISH
ENG
Hold the top and bottom of the TV frame
yy
firmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
When transporting the TV, do not expose the
yy
TV to jolts or excessive vibration.
When transporting the TV, keep the TV
yy
upright, never turn the TV on its side or tilt
towards the left or right.
ASSEMBLING AND PREPARING
15
Setting up the TV
Put your TV on a pedestal stand and mount the TV on a table or wall.
Attaching the stand
If you are not mounting the TV to a wall, use the following instructions to attach the stand.
1
3 EA
M5 x 16
Stand Body
Front
Stand Base
Caution
When attaching the stand to the TV
yy
set, place the screen facing down on a
cushioned table or flat surface to protect
the screen from scratches.
3
4 EA
M4 x 30
Caution
Make sure that the screws are fastened
yy
completely. (If they are not fastened
securely enough, the TV may tilt forward
after being installed.)
Do not fasten the screws with too much
yy
force; otherwise they may be worn out
and get loosened.
ENG
ENGLISH
2
16
ASSEMBLING AND PREPARING
Attaching the protection cover
Tidying cables
1 Remove the stand before installing the TV
1 Install the power cord holder and power cord.
on a wall mount by performing the stand
attachment in reverse.
After removing the stand, push the supplied
protection cover into the opening at the bottom
of the TV until it locks in place.
This will protect the opening from accumulating
dust and dirt.
It will help prevent the power cable from being
removed by accident.
Power cord holder
2 Gather and bind the cables with the cable
holder.
Protection cover
2 Secure the TV and the protection cover with
the 2 screws.
ENGLISH
ENG
Cable holder
Caution
Do not move the TV by holding the cable
yy
holder and power cord holder, as the cable
holders may break, and injuries and damage
to the TV may occur.
2 EA
M4 x 30
Caution
Make sure that the screws are fastened
yy
completely. (If they are not fastened
securely enough, the TV may tilt forward
after being installed.)
Do not fasten the screws with too much
yy
force; otherwise they may be worn out
and get loosened.
ASSEMBLING AND PREPARING
Mounting on a table
17
Securing the TV to a wall (For PA4900 series)
1 Lift and tilt the TV into its upright position on a
table.
-Leave a 10 cm (4 inch) (minimum) space from
the wall for proper ventilation.
10 cm (4 inch)
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
1 Insert and tighten the eye-bolts on the back of
the TV.
Do not place the TV near or on sources
yy
of heat, as this may result in fire or other
damage.
-If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall.
Adjusting the angle of the TV to suit view
Swivel 20 degrees to the left or right and adjust
the angle of the TV to suit your view.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly
with a sturdy rope.
Make sure to keep the rope horizontal with the
flat surface.
20
20
Caution
Make sure that children do not climb on or
yy
hang on the TV.
Note
Caution
When adjusting the angle of the TV, watch
yy
out for your fingers.
- Personal injury may occur if hands or fingers
are pinched. If the product is tilted too
much, it may fall, causing damage or injury.
se a platform or cabinet that is strong and
U
yy
large enough to support the TV securely.
ENG
ENGLISH
Caution
18
ASSEMBLING AND PREPARING
Mounting on a wall
Caution
Attach an optional wall mount bracket at the rear
of the TV carefully and install the wall mount
bracket on a solid wall perpendicular to the
floor. When you attach the TV to other building
materials, please contact qualified personnel.
LG recommends that wall mounting be performed
by a qualified professional installer.
10 cm (4 inch)
10 cm
Disconnect the power first, and then move
yy
or install the TV. Otherwise electric shock
may occur.
If you install the TV on a ceiling or slanted
yy
wall, it may fall and result in severe injury.
Use an authorized LG wall mount and contact
the local dealer or qualified personnel.
Do not over tighten the screws as this may
yy
cause damage to the TV and void your
warranty.
Use the screws and wall mounts that meet
yy
the VESA standard. Any damages or injuries
by misuse or using an improper accessory
are not covered by the warranty.
10 cm
Note
10 cm
ENGLISH
ENG
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are described
in the following table.
Model
42/50PA4500,
50PA4510,
42/50PA4900,
50PA5500,
50PA6500,
42/50PA450C,
50PA550C
60PA5500,
60PA6500,
60PA6550,
60PA550C
VESA
Standard screw
Number of screws
Wall mount
bracket (optional)
400 x 400
M6
4
PSW400B
600 x 400
M8
4
PSW600B
PSW420BX
PSW620BX
Use the screws that are listed on the VESA
yy
standard screw specifications.
The wall mount kit includes an installation
yy
manual and necessary parts.
The wall mount bracket is optional. You can
yy
obtain additional accessories from your local
dealer.
The length of screws may differ depending
yy
on the wall mount. Make sure to use the
proper length.
For more information, refer to the manual
yy
supplied with the wall mount.
MAKING CONNECTIONS
19
MAKING CONNECTIONS
Connect various external devices to the TV and switch input modes to select an external device. For more
information on external device’s connection, refer to the manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC,
gaming devices, and other external devices.
NOTE
If you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input cable
yy
to the TV through a DVD recorder or VCR. For more information on recording, refer to the manual
provided with the connected device.
The external device connection may differ from the model.
yy
Connect external devices to the TV regardless of the order of the TV port.
yy
If you connect a gaming device to the TV, use the cable supplied with the gaming device.
yy
Refer to the external equipment’s manual for operating instructions.
yy
Connecting to an antenna or cable
Connect an antenna, cable, or cable box to watch TV while referring to the following. The illustrations may
differ from the actual items and a RF cable is optional.
UHF Antenna
Antenna
ANTENNA/
CABLE IN
Coaxial (75Ω)
Terminal
Caution
Make sure not to bend the copper wire of
yy
the RF cable.
Copper wire
Complete all connections between devices,
yy
and then connect the power cord to the
power outlet to prevent damage to your TV.
NOTE
Use a signal splitter to use more than 2 TVs.
yy
Visit http://lgknowledgebase.com for more
yy
information about the antenna and cable
connection. Search for antenna.
ENG
ENGLISH
VHF Antenna
20
MAKING CONNECTIONS
This part of MAKING CONNECTIONS mainly uses picture for PA6500 series.
yy
Connecting to a HD receiver, DVD, or VCR player
Connect a HD receiver, DVD, or VCR player to the TV and select an appropriate input mode.
HDMI Connection
HDMI is the best way to connect a device.
Transmits the digital video and audio signals from an external device to the TV. Connect the external device
and the TV with the HDMI cable as shown in the following illustration.
NOTE
IN 3
Use the latest High Speed HDMI™ Cable with CEC (Customer Electronics Control) function.
yy
High Speed HDMI™ Cables are tested to carry an HD signal up to 1080p and higher.
yy
ENGLISH
ENG
IN 2
Choose any HDMI IN input port to connect.
It does not matter which port you use.
HDMI
(*Not Provided)
DVD / Blu-Ray / HD Cable Box / HD STB
1
IN
/ DVI
MAKING CONNECTIONS
21
DVI to HDMI Connection
Transmits the digital video signal from an external device to the TV. Connect the external device and the
TV with the DVI-HDMI cable as shown in the following illustration. To transmit an audio signal, connect an
audio cable.
1
IN
/ DVI
(*Not Provided)
DVI OUT
(*Not Provided)
AUDIO OUT
DVD / Blu-Ray / HD Cable Box
ENG
ENGLISH
AUDIO IN
(RGB/DVI)
22
MAKING CONNECTIONS
Component Connection
Transmits the analog video and audio signals from an external device to the TV. Connect the external
device and the TV with the component cable as shown in the following illustration.
NOTE
If cables are installed incorrectly, it could cause the image to display in black and white or with
yy
distorted color.
Check to ensure the cables are matched with the corresponding color connection.
yy
AV IN
ENGLISH
ENG
COMPONENT IN
VIDEO
L/MONO AUDIO R
2
Y
PB
PR
L
R
1
AUDIO
VIDEO
RED
(*Not Provided)
RED
WHITE
RED
BLUE
(*Not Provided)
BLUE
GREEN
VIDEO
RED
WHITE
GREEN
L
R
AUDIO
DVD / Blu-Ray / HD Cable Box
MAKING CONNECTIONS
23
Composite Connection
Transmits the analog video and audio signals from an external device to the TV. Connect the external
device and the TV with the composite cable as shown in the following illustration.
NOTE
yyIf you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the TV.
AV IN
L/MONO AUDIO R
2
PB
PR
L
R
RED
Y
WHITE
1
YELLOW
ENG
ENGLISH
COMPONENT IN
VIDEO
(*Not Provided)
RED
WHITE
YELLOW
VIDEO
L (MONO) AUDIO R
VCR / DVD / Blu-Ray / HD Cable Box
24
MAKING CONNECTIONS
Connecting to a PC
NOTE
It is recommended to use the TV with the HDMI connection for the best image quality.
yy
Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use.
yy
In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or
yy
brightness. If noise is present, change the PC output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
The synchronization input form for Horizontal and Vertical frequencies is separate.
yy
Depending on the graphics card, some resolution settings may not allow the image to be positioned
yy
on the screen properly.
HDMI Connection, DVI to HDMI Connection or RGB Connection
Choose method A, B, or C to make connection.
Method A: HDMI Connection
IN 2
IN 3
ENGLISH
ENG
Choose any HDMI input port to connect.
It does not matter which port you use.
HDMI
(*Not Provided)
PC
/ DVI
㶌⸬ (ARC)
IN
IN 2
1
AUDIO IN
(RGB/DVI)
1
1
IN
/ DVI
IN
/ DVI
MAKING CONNECTIONS
25
IN 2
㶌⸬ (ARC)
Method B: DVI to HDMI Connection
IN
1
/ DVI
AUDIO IN
(RGB/DVI)
(*Not Provided)
AUDIO IN
(RGB/DVI)
(*Not Provided)
$8',2287
'9,287
$8',2287
ENG
ENGLISH
PC
Method C: RGB Connection
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
(*Not Provided)
(*Not Provided)
$8',2287
5*%2873& 5*%2873&
$8',2287
'9,287
PC
26
MAKING CONNECTIONS
Connecting to an Audio System
Use an optional external audio system instead of the built-in speaker.
NOTE
If you use an optional external audio device instead of the built-in speaker, set the TV speaker feature
yy
to off.
Digital Optical Audio Connection
Transmits the digital audio signal from the TV to an external device. Connect the external device and the
TV with the optical audio cable as shown in the following illustration.
ENGLISH
ENG
OPTICAL
DIGITAL
AUDIO OUT
(*Not Provided)
OPTICAL AUDIO IN
Digital Audio System
MAKING CONNECTIONS
27
Connecting to a USB
Connect a USB storage device such as a USB flash memory, external hard drive, or a USB memory card
reader to the TV and access the My media menu to use various multimedia files.
USB IN
(*Not Provided)
USB
or
ENG
ENGLISH
28
REMOTE CONTROL
REMOTE CONTROL
The descriptions in this manual are based on the buttons on
the remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace
batteries (1.5 V AAA) matching the and ends to the
label inside the compartment, and close the battery cover.
To remove the batteries, perform the installation actions in
reverse.
or
CAUTION
Do not mix old and new batteries, as this may damage the remote control.
yy
Make sure to point the remote control toward the remote control sensor on the TV.
For 42PA4500, 42PA450C
ENERGY
POWER
Turns the TV on or off.
POWER
TV
ENGLISH
ENG
SAVING
AV MODE INFO
RATIO
INPUT
ꕊ ENERGY SAVING
Adjusts the brightness of the screen to reduce energy
consumption.
TV
FLASHBK
AV MODE
Selects an AV mode.
INFO
Views the information of the current program and screen.
RATIO
Resizes an image.
LIST
SETTINGS
Returns to the last TV channel.
Q.MENU
INPUT
Changes the input source; Turns the TV on.
OK
EXIT
LIST, - (Dash)
LIST: Accesses the saved channel list.
- (Dash): Inserts a dash between numbers such as 2-1 and 2-2.
FAV
VOL
CH
MUTE
Number button
Enters numbers.
P
A
G
E
FLASHBK
Alternates between the two last channels selected (pressing
repeatedly).
REMOTE CONTROL
ENERGY
SETTINGS
Accesses the main menu.
POWER
TV
SAVING
AV MODE INFO
RATIO
29
Q. MENU
Accesses the quick menu.
INPUT
FLASHBK
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
OK ꔉ
Selects menus or options and confirms your input.
ꕣ (BACK)
Returns to the previous level.
EXIT ꕯ
Clears all on-screen displays and returns to TV viewing.
LIST
SETTINGS
Q.MENU
VOL
Adjusts the volume level.
OK
FAV
VOL
CH
MUTE
P
A
G
E
FAV
Accesses your favorite channel list.;
Selects a menu or option.
Accesses the AV devices connected to the TV;
Opens the SIMPLINK menu.
MUTE
Mutes all sounds.
CH , PAGE
CH: Scrolls through the saved channels.
PAGE: Moves to the previous or next screen.
Color buttons
These access special functions in some menus.
Control buttons
Controls the SIMPLINK compatible devices (USB,SIMPLINK).
ꕘ (FREEZE)
Freezes the current frame (Not supported when using
USB Mode and Simplink).
Not functional
ENG
ENGLISH
EXIT
30
REMOTE CONTROL
For 50PA4500, 50PA4510, 50PA450C, PA4900, PA5500, PA6500, PA6550, PA550C series
RATIO
INPUT ENERGY
POWER
Turns the TV on or off.
TV
TV
SAVING
1
2
3
4
5
6
7
8
9
0
FLASHBK
LIST
RATIO
Resizes an image.
INPUT
Changes the input source; Turns the TV on.
ꕊ ENERGY SAVING
Adjusts the brightness of the screen to reduce energy
consumption.
FAV
ENGLISH
ENG
VOL
INFO
CH
MUTE
SETTINGS AV MODE Q.MENU
OK
EXIT
Returns to the last TV channel.
P
A
G
E
Number button
Enters numbers.
LIST, - (Dash)
LIST: Accesses the saved channel list.
- (Dash): Inserts a dash between numbers such as 2-1 and 2-2.
FLASHBK
Alternates between the two last channels selected (pressing
repeatedly).
REMOTE CONTROL
RATIO
INPUT ENERGY
VOL
Adjusts the volume level.
SAVING
FAV
Accesses your favorite channel list.;
Selects a menu or option.
TV
1
2
3
INFO
Views the information of the current program and screen.
4
5
6
MUTE
Mutes all sounds.
7
8
9
^ CH v,
0
FLASHBK
LIST
PAGE
CH: Scrolls through the saved channels.
PAGE: Moves to the previous or next screen.
FAV
INFO
CH
MUTE
SETTINGS AV MODE Q.MENU
P
A
G
E
SETTINGS
Accesses the main menu.
AV MODE
Selects an AV mode.
Q. MENU
Accesses the quick menu.
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
OK ꔉ
Selects menus or options and confirms your input.
OK
ꕣ (BACK)
Returns to the previous level.
EXIT
Accesses the AV devices connected to the TV;
Opens the SIMPLINK menu.
EXIT ꕯ
Clears all on-screen displays and returns to TV viewing.
Color buttons
These access special functions in some menus.
Control buttons
Controls the SIMPLINK compatible devices (USB,SIMPLINK).
ꕘ (FREEZE)
Freezes the current frame (Not supported when using
USB Mode and Simplink).
ENG
ENGLISH
VOL
31
32
WATCHING TV
WATCHING TV
Turning the TV on for the first
time
When you turn the TV on for the first time, the
Initial setting screen appears. Select a language
and customize the basic settings.
1 Connect the power cord to a power outlet.
2 In Standby mode, press the power button on
4 When the basic settings are complete,
press OK.
NOTE
If you do not complete the Initial setting,
yy
it will appear whenever the TV turns on.
Disconnect the power cord from the
yy
power outlet when you do not use the
TV for a long period of time.
the remote control to turn the TV on.
The Initial setting screen appears if you turn
the TV on for the first time.
NOTE
You can also access Initial Setting by
yy
accessing OPTION in the main menu.
3 Follow the on-screen instructions to customize
ENGLISH
ENG
your TV settings according to your preferences.
Language
Selects a language to
display.

Mode Setting
Selects Home Use for
the home environment.

Time Zone
Selects the time zone
and daylight saving.

Auto Tuning
Scans and saves available
channels automatically.
NOTE
To display images in the best quality for
yy
your home environment, select Home
Use.
Store Demo is suitable for the retail
yy
environment.
If you select Store Demo, any
yy
customized settings will switch back to
the default settings of Store Demo in 5
minutes.
5 To turn the TV off, press the power button on
the remote control.
USING THE USER GUIDE
33
USING THE USER GUIdE
User Guide allows you to more easily access the
detailed TV information.
User Guide
1
OPTION > To set language
SETTINGS  OPTION  Language
1 Press SETTINGS to access the main menus.
You can select the language of the menu displayed on the screen and digital
sound broadcasting.
yy Menu Language : Selects a language for the display text.
yy Audio Language [In Digital Mode Only] : Select the desired language when
watching digital broadcasting containg several voice languages.
CHANNEL Setting
PICTURE, SOUND Setting
2 Press the RED button to access the Customer
OPTION
Support menus.
Advanced Function
Information
2
PICTURE
AUDIO
CHANNEL
TIME
LOCK
OPTION
INPUT
MY MEDIA
Zoom In
Close
SETTINGS  OPTION  Language
You can select the language of the menu displayed on the screen and digital
sound broadcasting.
y Menu Language : Selects a language for the display text.
y Audio Language [In Digital Mode Only] : elect the desired language when
watching digital broadcasting containg several voice languages.
y
y
Press OK(ꔉ) to set your option settings.
Customer Support
ꕣ Exit

□ Picture Test
□ Sound Test
2
□ Product/Service Info.
1
Shows the description of the selected menu.
You can use ꕌ/ꕍ to move between pages.
2
Zooms in or out the screen.
Close
3 Press the Navigation buttons to scroll to
User Guide and press OK.
User Guide
3
2
To use input device
To use Energy Saving feature
CHANNEL Setting
To set time options
PICTURE, SOUND Setting
OPTION
To set TV lock options
To set language
Advanced Function
To set caption
Information
1
To set other options
1
Allows to select the category you want.
2
Allows to select the item you want.
You can use ꕌ/ꕍ to move between pages.
3
Allows to browse the description of the
function you want from the index.
Close
ENG
ENGLISH
ꔑ User Guide
Zoom Out
34
TROUBLESHOOTING
TROUBLESHOOTING
General
Problem
Solution
Cannot control the TV with the
remote control.
yyCheck the remote control sensor on the product and try again.
yyCheck if there is any obstacle between the product and the remote control.
to ).
yyCheck if the batteries are still working and properly installed ( to ,
No image display and no sound is
produced.
yyCheck if the product is turned on.
yyCheck if the power cord is connected to a wall outlet.
yyCheck if there is a problem in the wall outlet by connecting other products.
The TV turns off suddenly.
yyCheck the power control settings. The power supply may be interrupted.
yyCheck if the Auto sleep feature is activated in the Time settings.
yyIf there is no signal while the TV is on, the TV will turn off automatically after
15 minutes of inactivity.
Pentouch
Problem
Solution
yyCheck that you used the remote control to enter Pentouch mode.
yyCheck that the Pentouch dongle is connected to the computer and the red
LED is on.
yyPress the (POWER) button on the touch pen to check that it is powered on.
yyCheck that the touch pen is paired for use. (The touch pen is correctly paired if
the red LED is on once when you press the Touch Home button on the touch
pen.)
yySet the computer screen to display only on the TV.
The TV screen doesn’t look normal
when using Pentouch.
yyCheck that the computer is correctly connected to the TV.
yyCheck that you are using the optimal resolution.
yySet the aspect ratio on the TV to Just Scan.
ENGLISH
ENG
The touch pen does not work.
The touch pen is touched on wrong yySet the computer screen to display only on the TV.
positions.
yyIf the point you touch on the TV screen using the touch pen and the point
indicated as touched on the computer screen do not match when the
computer and the TV are connected by a PC signal (RGB) cable, use the TV
remote control to select [SETTINGS] → [Picture] → [Screen] (RGB-PC), then
select [Auto Config.] to adjust the screen.
The touch pen movement is not
smooth.
yyCheck whether the computer and the TV are too far from each other. Check
whether there are too many obstructions between the computer and the TV.
yyCheck whether many other applications are running on the computer. (Please
avoid running other applications while using the Pentouch program.)
SPECIFICATIONS
35
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
Power requirement
AC100 - 240 V ~ 50/60 Hz
Television System
NTSC-M, ATSC, 64 & 256 QAM
Program Coverage
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
External Antenna Impedance
75 Ω
Environment
condition
Operating
Temperature
0 - 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 - 60 °C
Storage Humidity
Less than 85 %
MODELS
Dimensions
(W x H x D)
983.6 mm x 655.0 mm x 246.7 mm
(38.7 inch x 25.7 inch x 9.7 inch)
1168.0 mm x 758.0 mm x 297.0 mm
(45.9 inch x 29.8 inch x 11.6 inch)
Without stand
983.6 mm x 601.3 mm x 58.0 mm
(38.7 inch x 23.6 inch x 2.2 inch)
1168.0 mm x 704.0 mm x 53.0 mm
(45.9 inch x 27.7 inch x 2.0 inch)
With stand
20.6 kg (45.4 lbs)
28.2 kg (62.1 lbs)
Without stand
19.0 kg (41.8 lbs)
25.8 kg (56.8 lbs)
2.1 A / 210 W
2.8 A / 280 W
42PA4900
(42PA4900-UK)
50PA4900
(50PA4900-UK)
With stand
983.6 mm x 655.0 mm x 246.7 mm
(38.7 inch x 25.7 inch x 9.7 inch)
1168.0 mm x 758.0 mm x 297.0 mm
(45.9 inch x 29.8 inch x 11.6 inch)
Without stand
983.6 mm x 601.3 mm x 58.0 mm
(38.7 inch x 23.6 inch x 2.2 inch)
1168.0 mm x 704.0 mm x 53.0 mm
(45.9 inch x 27.7 inch x 2.0 inch)
MODELS
Weight
With stand
20.6 kg (45.4 lbs)
28.2 kg (62.1 lbs)
Without stand
19.0 kg (41.8 lbs)
25.8 kg (56.8 lbs)
2.1 A / 210 W
2.8 A / 280 W
50PA5500
(50PA5500-UG)
60PA5500
(60PA5500-UG)
Current Value / Power consumption
MODELS
Dimensions
(W x H x D)
Weight
50PA4510
(50PA4510-UJ)
With stand
Current Value / Power consumption
Dimensions
(W x H x D)
50PA4500
(50PA4500-UM)
50PA6500
(50PA6500-UG)
60PA6500
(60PA6500-UG)
60PA6550
(60PA6550-UM)
With stand
1168.0 mm x 758.0 mm x 297.0 mm 1386.8 mm x 883.2 mm x 354.7 mm
(45.9 inch x 29.8 inch x 11.6 inch)
(54.5 inch x 34.7 inch x 13.9 inch)
Without stand
1168.0 mm x 704.0 mm x 53.0 mm
(45.9 inch x 27.7 inch x 2.0 inch)
1386.8 mm x 818.2 mm x 53.0 mm
(54.5 inch x 32.2 inch x 2.0 inch)
With stand
28.8 kg (63.4 lbs)
40.6 kg (89.5 lbs)
Without stand
26.4 kg (58.2 lbs)
36.4 kg (80.2 lbs)
2.9 A / 290 W
4.3 A / 430 W
Current Value / Power consumption
ENG
ENGLISH
Weight
42PA4500
(42PA4500-UM)
36
SPECIFICATIONS
42PA450C
(42PA450C-UM)
50PA450C
(50PA450C-UM)
With stand
983.6 mm x 655.0 mm x 246.7 mm
(38.7 inch x 25.7 inch x 9.7 inch)
1168.0 mm x 758.0 mm x 297.0 mm
(45.9 inch x 29.8 inch x 11.6 inch)
Without stand
983.6 mm x 601.3 mm x 58.0 mm
(38.7 inch x 23.6 inch x 2.2 inch)
1168.0 mm x 704.0 mm x 53.0 mm
(45.9 inch x 27.7 inch x 2.0 inch)
MODELS
Dimensions
(W x H x D)
Weight
With stand
20.6 kg (45.4 lbs)
28.2 kg (62.1 lbs)
Without stand
19.0 kg (41.8 lbs)
25.8 kg (56.8 lbs)
2.1 A / 210 W
2.8 A / 280 W
50PA550C
(50PA550C-UG)
60PA550C
(60PA550C-UG)
Current Value / Power consumption
MODELS
Dimensions
(W x H x D)
Weight
With stand
1168.0 mm x 758.0 mm x 297.0 mm 1386.8 mm x 883.2 mm x 354.7 mm
(45.9 inch x 29.8 inch x 11.6 inch)
(54.5 inch x 34.7 inch x 13.9 inch)
Without stand
1168.0 mm x 704.0 mm x 53.0 mm
(45.9 inch x 27.7 inch x 2.0 inch)
1386.8 mm x 818.2 mm x 53.0 mm
(54.5 inch x 32.2 inch x 2.0 inch)
With stand
28.8 kg (63.4 lbs)
40.6 kg (89.5 lbs)
Without stand
26.4 kg (58.2 lbs)
36.4 kg (80.2 lbs)
2.9 A / 290 W
4.3 A / 430 W
Current Value / Power consumption
ENGLISH
ENG
Video Supported Formats (Depending on model)
File
Video Decoder
Extension
name
mpg, mpeg
MPEG1, MPEG2
Audio Codec
Max Resolution
MP2, MP3, Dolby Digital, LPCM
dat
MPEG1
MP2
ts, trp, tp
MPEG2, H.264, AVS, VC1
MP2, MP3, Dolby Digital, AAC, HE-AAC
vob
MPEG1, 2
MP2, MP3, Dolby Digital, LPCM
mp4, mov, m4v
MPEG4,DivX 3.11, DivX 4.12,
DivX 5.x, DivX 6, Xvid 1.00, Xvid
1.01, Xvid 1.02, Xvid 1.03, Xvid
1.10-beta1/2H.264
AAC, HE-AAC, MP3
mkv
H.264, MPEG-1,2,4
MP2, MP3, Dolby Digital, AAC
HE-AAC, LPCM
divx, avi
MPEG2, MPEG4, DivX 3.11, DivX
4, DivX 5, DivX 6, Xvid 1.00, Xvid
1.01, Xvid 1.02, Xvid 1.03, Xvid
1.10-beta1/2H.264
MP2, MP3, Dolby Digital, LPCM,
ADPCM, AAC, HE-AAC
Motion JPEG
(avi, mp4, mkv)
JPEG
LPCM, ADPCM
asf, wmv
VC1
WMA
flv
Sorenson H.263, H264
MP3, AAC
1920 x 1080 @ 30p
(Only Motion JPEG
640x480@30p)
SPECIFICATIONS
RGB (PC), HDMI (PC) supported mode
Resolution
Horizontal
Vertical
Frequency (KHz) Frequency (Hz)
Component port connecting information
Component ports on the
TV
Y
PB
PR
720x400
31.469
70.08
640x350
31.468
70.09
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
640x480
31.469
59.94
800x600
37.879
60.31
1024x768
48.363
60.00
1360x768
47.712
60.015
1280x1024
HDMI-PC
63.981
60.02
1920x1080
67.5
60.00
For 50/60PA5500, 50/60PA6500, 60PA6550,
50/60PA550C
HDMI (DTV) supported mode
Resolution
Horizontal
Vertical
Frequency (KHz) Frequency (Hz)
31.47
31.50
59.94
60.00
1280x720p
44.96
45.00
59.94
60.00
1920x1080i
33.72
33.75
59.94
60.00
1920x1080p
26.97
27.00
33.71
33.75
67.432
67.50
23.976
24.00
29.97
30.00
59.94
60.00
Video output ports
on DVD player
Component supported mode
Resolution
Horizontal
Vertical
Frequency (KHz) Frequency (Hz)
720x480i
15.73
15.73
59.94
60.00
720x480p
31.47
31.50
59.94
60.00
1280x720p
44.96
45.00
59.94
60.00
1920x1080i
33.72
33.75
59.94
60.00
1920x1080p
26.97
27.00
33.71
33.75
67.432
67.50
23.976
24.00
29.97
30.00
59.94
60.00
ENG
ENGLISH
720x480p
37
38
MAINTENANCE
MAINTENANCE
Cleaning Your TV
Clean your TV regularly to keep the best
performance and to extend the product lifespan.
Caution
Make sure to turn the power off and
yy
disconnect the power cord and all other
cables first.
When the TV is left unattended and unused
yy
for a long time, disconnect the power cord
from the wall outlet to prevent possible
damage from lightning or power surges.
Screen, frame, cabinet and stand
ENGLISH
ENG
To remove dust or light dirt, wipe the surface with
a dry, clean, and soft cloth.
To remove major dirt, wipe the surface with a
soft cloth dampened in clean water or a diluted
mild detergent. Then wipe immediately with a dry
cloth.
Caution
Do not push, rub, or hit the surface with
yy
your fingernail or a sharp object, as this may
result in scratches on the screen and image
distortions.
Do not use any chemicals, such as waxes,
yy
benzene, alcohol, thinners, insecticides, air
fresheners, lubricants, as these may damage
the screen’s finish and cause discoloration.
Do not spray liquid onto the surface. If water
yy
enters the TV, it may result in fire, electric
shock, or malfunction.
Power cord
Remove the accumulated dust or dirt on the
power cord regularly.
CHILD SAFETY:
It Makes A Difference How and Where
You Use Your Flat Panel Display
Congratulations on your purchase! As you enjoy your new product,
please keep these safety tips in mind:
THE ISSUE
yy The home theater entertainment experience is a growing trend and
larger flat panel displays are popular purchases. However, flat panel
displays are not always supported on the proper stands or installed
according to the manufacturer’s recommendations.
yy Flat panel displays that are inappropriately situated on dressers,
bookcases, shelves, desks, speakers, chests or carts may fall over and
cause injury.
THIS MANUFACURER CARES!
yy The consumer electronics industry is committed to making home
entertainment enjoyable and safe.
TUNE INTO SAFETY
yy O n e s i z e d o e s N O T f i t a l l . F o l l o w t h e m a n u f a c t u r e r ’ s
recommendations for the safe installation and use of your flat panel
display.
yy Carefully read and understand all enclosed instructions for proper use
of this product.
yy Don’t allow children to climb on or play with furniture and television
sets.
yy Don’t allow place flat panel displays on furniture that can easily be
used as steps, such as a chest of drawers.
yy Remember that children can become excited while watching
a program, especially on a “larger than life” flat panel display.
Care should be taken to place or install the display where it cannot be
pushed, pulled over, or knocked down.
yy Care should be taken to route all cords and cables connected to the
flat panel display so that they cannot be pulled or grabbed by curious
children.
WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT
YOUR FLAT PANEL DISPLAY, ALWAYS:
yy Use a mount that has been recommended by the display
manufacturer and/or listed by an independent laboratory
(such as UL, CSA, ETL).
yy Follow all instructions supplied by the display and wall mount
manufacturers.
yy If you have any doubts about your ability to safely install your flat
panel display, contact your retailer about professional installation.
yy Make sure that the wall where you are mounting the display is
appropriate. Some wall mounts are not designed to be mounted
to walls with steel studs or old cinder block construction.
If you are unsure, contact a professional installer.
yy A m i n i m u m o f t w o p e o p l e a r e r e q u i r e d f o r i n s t a l l a t i o n .
Flat panel displays can be heavy
The model and serial number of the TV is
located on the back and/or one side of the TV.
Record it below should you ever need service.
MODEL
SERIAL
LG Customer Information Center
For inquires or comments, visit www.lg.com or call;
1-800-243-0000
1-888-865-3026
1-888-542-2623
USA, Consumer User
USA, Commercial User
CANADA
Register your product Online!
www.lg.com
(For PA4900 series)
The extended owner’s manuals that contain
information on the advanced features of this LG
TV are located on the CD-ROM provided in an
electronic version.
To read these files, you will need to use the personal
computer (PC) equipped with a CD-ROM drive.
(For PA450C/PA4500/PA4510 series, 50PA550C, 50PA4900,
50PA5500, 50PA6500 USA, Canada, Mexico)
This product qualifies for ENERGY STAR in the
“factory default (Home Use)” setting.
Changing the factory default settings or enabling other
features may increase power consumption that could
exceed the limits necessary to quality for ENERGY STAR.
OWNER’S MANUAL
EXTERNAL CONTROL
DEVICE SETUP
Please read this manual carefully before operating your set and retain it
for future reference.
www.lg.com
2
EXTERNAL CONTROL DEVICE SETUP
IR CODES
(Depending on model)
How to Connect
Connect your wired remote control to the Remote Control port on the TV.
Remote Control IR Codes
Output waveform
Single pulse, modulated with 37.917kHz signal at 455kHz
Tc
T1
Frame configuration
ENGLISH
ENG
1st frame
Lead code
Low custom code
High custom code
Data code
Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
Repeat frame
Repeat code
Tf
Lead code
9 ms
4.5 ms
Repeat code
0.55 ms
9 ms
2.25 ms
Bit description
Bit “0”
Bit “1”
0.56 ms
0.56 ms
2.24 ms
1.12 ms
Frame interval: Tf
The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms @455KHz
EXTERNAL CONTROL DEVICE SETUP
Code
(Hexa)
Function
(POWER)
Note
Code
(Hexa)
Function
Note
Remote control Button
(Power On/Off)
0F
TV
Remote control Button
DC
3D
Remote control Button
42
Q.MENU/MY APPS Remote control Button
5B
EXIT
Remote control Button
43
SETTINGS
Remote control Button
7C
HOME
Remote control Button
7A
08
0B
INPUT
Remote control Button
10 - 19
Number Key 0-9
Remote control Button
4C
- (Dash)/LIST
Remote control Button
1A
FLASHBK
Remote control Button
09
MUTE
Remote control Button
02
VOL +
Remote control Button
03
VOL -
Remote control Button
00
CH ^
Remote control Button
01
CH v
Remote control Button
1E
Remote control Button
^
Remote control Button
41
v
Remote control Button
07
<
Remote control Button
06
>
Remote control Button
44
OK
Remote control Button
28
79
BA
(BACK)
RATIO
REC
Remote control Button
D6
TV
Discrete IR Code
(TV Input Selection)
C4
POWER ON
Discrete IR Code
(Only Power Off)
C5
POWER OFF
Discrete IR Code
(Only Power Off)
5A
AV
Discrete IR Code
(AV Input Selection)
BF
COMPONENT1
Discrete IR Code
(Component1 Input
Selection)
D4
COMPONENT2
Discrete IR Code
(Component2 Input
Selection)
D5
RGB-PC
Discrete IR Code
(RGB-PC Input Selection)
CE
HDMI1
Discrete IR Code
(HDMI1 Input Selection)
CC
HDMI2
Discrete IR Code
(HDMI2 Input Selection)
E9
HDMI3
Discrete IR Code
(HDMI3 Input Selection)
DA
HDMI4
Discrete IR Code
(HDMI4 Input Selection)
76
Ratio 4:3
Discrete IR Code
(Only 4:3 Mode)
77
Ratio 16:9
Discrete IR Code
(Only 16:9 Mode)
AF
Ratio Cinema
Zoom
Discrete IR Code
(Only Cinema Zoom Mode)
Remote control Button
Remote control Button
yy (FREEZE)
Remote control Button
95
ENERGY SAVING
Remote control Button
7E
SIMPLINK
Remote control Button
AA
INFO
Remote control Button
30
AV MODE
Remote control Button
72
RED
Remote control Button
71
GREEN
Remote control Button
63
YELLOW
Remote control Button
61
BLUE
Remote control Button
B1
n
Remote control Button
B0

Remote control Button
BA
yy
Remote control Button
8E

Remote control Button
8F

Remote control Button
Use the feature depending on your model.
yy
ENG
ENGLISH
FAV/MARK
40
(User-Guide)
3
4
EXTERNAL CONTROL DEVICE SETUP
EXTERNAL CONTROL DEVICE SETUP
RS-232C Setup
Connect the RS-232C (serial port) input jack to
an external control device (such as a computer or
an A/V control system) to control the product’s
functions externally.
Connect the serial port of the control device to the
RS-232C jack on the product back panel.
Type of connector;
D-Sub 9-Pin Male
1
Note
RS-232C on this TV is intended to be used
yy
with third party RS-232C control hardware
and software. The instructions below
are provided to help with programming
software or to test functionality using telenet
software. RS-232C connection cables are not
supplied with the product.
5
6
9
RS-232C IN
(CONTROL & SERVICE)
No.
Pin name
ENGLISH
ENG
1
No connection
2
RXD (Receive data)
3
TXD (Transmit data)
4
DTR (DTE side ready)
5
GND
6
DSR (DCE side ready)
7
RTS (Ready to send)
8
CTS (Clear to send)
9
No Connection
EXTERNAL CONTROL DEVICE SETUP
RS-232C configurations
Set ID
Set ID number.
7-Wire Configuration
(Serial female-female NULL modem cable)
PC
RXD
X
OPTION
TV
2
3
• Language
TXD
• Caption
: Off
• ISM Method
: Normal
TXD
3
2
RXD
GND
5
5
GND
DTR
4
6
DSR
DSR
6
4
DTR
RTS
7
8
CTS
1 Press SETTINGS to access the main menu.
CTS
8
7
RTS
2 Press the Navigation buttons to scroll to
D-Sub 9
5
• Pointer
• Balloon Help : On
• Initial Setting
• Set ID
:1
?
SETUP and press OK.
D-Sub 9
3 Press the Navigation buttons to scroll to
option and press OK.
3-Wire Configurations(Not standard)
4 Press the Navigation buttons to scroll to Set ID
3
TXD
TXD
3
2
RXD
GND
5
5
GND
DTR
4
6
DSR
DSR
6
4
DTR
RTS
7
8
CTS
CTS
8
7
RTS
D-Sub 9
D-Sub 9
and press OK.
5 Scroll left or right to select a set ID number and
select close. The adjustment range is 1-99.
6 When you are finished, press EXIT.
*Real data mapping
0 : Step 0
…
2
A : Step 10 (SET ID 10)
F : Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
63 : Step 99 (SET ID 99)
64 : Step 100
ENG
ENGLISH
RXD
…
TV
…
PC
6
EXTERNAL CONTROL DEVICE SETUP
Communication Parameters
Stop bit: 1 bit
yy
Communication code: ASCII code
yy
Use a crossed (reverse) cable.
yy
Baud rate: 9600 bps (UART)
yy
Data length: 8 bits
yy
Parity : None
yy
Command reference list
01. Power
COMMAND1
COMMAND2
DATA
(Hexadecimal)
k
a
00 - 01
COMMAND1
COMMAND2
DATA
(Hexadecimal)
14. Balance
k
t
00 - 64
x
t
(See p.9)
ENGLISH
ENG
02. Input Select x
b
(See p.8)
15. 3D (For 3D
TV)
03. Aspect
Ratio
k
c
(See p.8)
16. Color
Temperature
x
u
00 - 64
04. Screen
Mute
k
d
00 - 01
17.Extended
3D (For 3D TV)
x
v
(See p.9)
05. Volume
Mute
k
e
00 - 01
18. ISM
Method
j
p
(See p.9)
06. Volume
Control
k
f
00 - 64
19. Energy
Saving
j
q
(See p.9)
07. Contrast
k
g
00 - 64
20. Auto
Configuration
j
u
(See p.10)
08. Brightness
k
h
00 - 64
22. Channel
Add/Del
m
b
00 - 01
09. Color
k
i
00 - 64
23. Key
m
c
(See p.10)
10. Tint
k
j
00 - 64
11. Sharpness
k
k
00 - 32
12. OSD Select k
l
00 - 01
13. Remote
Control Lock
Mode
m
00 - 01
21. Channel
Tuning
k
COMMAND1 COMMAND2
DATA00
DATA01
DATA02
DATA03
DATA04
DATA05
(Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal)
m
physical
program
high
a
major
program
low
major low
minor high minor low
attribute
EXTERNAL CONTROL DEVICE SETUP
7
Transmission / Receiving protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the set.(j, k, m or x)
[Command 2] : Second command to control the set.
[Set ID] :You can adjust the set ID to choose desired set ID number in Option menu. Adjustment range is
1~ 99. When selecting Set ID ‘0’, every connected the set is controlled. Set ID is indicated as decimal (1~
99) on menu and as Hexa decimal (0x0~ 0x63) on transmission /receiving protocol.
[DATA] : To transmit the command data.
Transmit the ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ] : ASCII code ‘space (0x20)’
* In this model, set will not send the status during the standby mode.
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from nonviable functions or communication errors.
Data01: Illegal Code
Data02: Not supported function
Data03: Wait more time
* In this model, set will not send the status during the standby mode.
* Data Format
[Command 2] : Use as command.
[Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’.
[DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’.
[NG] : Use the large character
ENG
ENGLISH
The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
* In this model, set will not send the status during the standby mode.
* Data Format
[Command 2] : Use as command.
[Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’.
[DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’.
[OK] : Use the large character.
8
EXTERNAL CONTROL DEVICE SETUP
01. Power (Command: k a)
To control Power On/Off of the set.
Transmission [k][a][ ][Set ID][ ][Data][Cr]
Data 00: Power Off Data 01: Power On
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
* In a like manner, if other functions transmit ‘FF’
data based on this format, Acknowledgement data
feedback presents status about each function.
* Note: In this model, set will send the Acknowledge
after power on processing completion.
There might be a time delay between command and
acknowledge.
02. Input Select (Command: x b)
To select input source for set.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data 00: DTV (Antenna) Data 01: DTV (Cable)
Data 10: Analog (Antenna)
Data 11: Analog (Cable)
Data 20: AV or AV1 Data 21: AV2
Data 40: Component1
Data 41: Component2
Data 42: Component3
Data 60: RGB-PC
Data 90: HDMI1 Data 91: HDMI2
Data 92: HDMI3 Data 93: HDMI4
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
* Use the feature depending on your model.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01: 4:3 Data 02: 16:9 Data 04: Zoom
Data 06: Set by program
Data 09: Just scan
Data 10: Cinema Zoom 1
…
ENGLISH
ENG
03. Aspect Ratio (Command: k c)
To adjust the screen format.
Data 1F: Cinema Zoom16
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
04. Screen Mute (Command: k d)
To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00: Screen mute off (Picture on), Video-out Mute off
Data 01: Screen mute on (Picture off)
Data 10: Video-out Mute on
Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of Video-out Mute on only, TV will display On
Screen Display (OSD). But, in case of screen mute on,
TV will not display On Screen Display (OSD).
05. Volume Mute (Command: k e)
To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00: Volume mute on (Volume off)
Data 01: Volume mute off (Volume on)
Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]
06. Volume Control (Command: k f)
To adjust volume.
You can also adjust volume with the volume buttons on
remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to “Real data mapping”.
Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]
07. Contrast (Command: k g)
To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to “Real data mapping”.
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
08. Brightness (Command: k h)
To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to “Real data mapping”.
Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]
09. Color (Command: k i)
To adjust screen color.
You can also adjust color in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to “Real data mapping”.
Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]
10. Tint (Command: k j)
To adjust screen tint.
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red: 00 ~ Green: 64 (*transmit by Hexadecimal
code)
*Refer to “Real data mapping”.
Acknowledgement [ j ][ ][Set ID][ ][OK/NG][Data][x]
11. Sharpness (Command: k k)
To adjust screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 32 (*transmit by Hexadecimal code)
*Refer to “Real data mapping”.
Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
12. OSD Select (Command: k l)
To select OSD (On Screen Display) on/off.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00: OSD off Data 01: OSD on
Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]
13. Remote Control Lock Mode (Command: k m)
To lock the remote control and the front panel controls
on the set.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00: Lock off
Data 01: Lock on
Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]
If you’re not using the remote control and front panel
controls on the Monitor set, use this mode. When main
power is on/off, remote control lock is released.
If Key Lock is on in the standby mode, TV will not turn on
by POWER button of remote control and on the TV.
14. Balance (Command: k t)
To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to “Real data mapping”.
15. 3D (Command: x t) (For 3D TV)
To change 3D mode for TV.
Transmission [x][t][ ][Set ID][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][Cr]
Data1
00: 3D On
01: 3D Off
02: 3D to 2D
03: 2D to 3D
Data2
00: Top and Bottom
01: Side by Side
02: Check Board
03: Single Frame Sequential
04: Column interleaving 05: Row interleaving
Data3
00: Right to Left
01: Left to Right
Data4
3D Depth: Min : 00 ~ Max : 14
(*transmit by Hexadecimal code)
*If data1 is 01(3D Off) , data2 , data3 , data4 have no
meaning.
*If data1 is 02(3D to 2D), data2, data3 and data4 have no
meaning.
*I f data1 is 03(2D to 3D), data2 and data3 have no
meaning.
Data 01
00
01
02
03
Data 02
o
x
x
x
Data 03
o
x
x
x
Data 04
x
x
x
o
x : Don’t care
Acknowledgement [t][ ][OK][Data01][Data02]
[Data03][Data04][x][t][ ][NG][Data01][x]
16. Color Temperature (Command: x u)
To adjust color temperature.
You can also adjust color temperature in the PICTURE
menu.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to “Real data mapping”.
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
17. Extended 3D (Command: x v) (For 3D TV)
To change 3D option for TV. Use the feature depending
on your model.
Transmission [x][v][ ][Set ID][ ][Data01][ ][Data02][Cr]
Data1: 3D option
00: 3D Picture Correction
01: 3D Depth
02: 3D Viewpoint
07: 3D Sound Zooming
08: Normal Image View
09: 3D Mode
Data2: It has own range for each 3D option determined
by Data1.
1) When Data1 is 00
00: Right to Left
01: Left to Right
2) When Data1 is 01
Data Min: 00 ~ Max: 14 (*transmit by Hexadecimal code)
3) When Data1 is 02
Data Min: 00 ~ Max: 14 (*transmit by Hexadecimal code)
4) When Data1 is 07
00: Off 01: On
5) When Data1 is 08
00: Off 01: On
6) When Data1 is 09
00: Standard 01: Sports
02: Cinema 03: Extreme
04: Manual
Acknowledgement [v][ ][OK][Data01][Data02][x]
[v][ ][NG][Data01][x]
* Use the feature depending on your model.
18. ISM Method (Command: j p)
To avoid having a fixed image remain on screen.
Transmission [j][p][ ][Set ID][ ][Data][Cr]
Data 02: Orbiter
08: Normal
20: Color Wash
Acknowledgement [p][ ][Set ID][ ][OK/NG][Data][x]
19. Energy Saving (Command: j q)
To control the energy saving function.
Transmission [ j ][q][ ][Set ID][ ][Data][Cr]
Data 00: off
ENG
ENGLISH
Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]
9
10
EXTERNAL CONTROL DEVICE SETUP
01: Minimum
02: Medium
03: Maximum
04: Intelligent Sensor
05: Screen off
Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]
20. Auto Configuration (Command: j u)
To adjust picture position and minimize image shaking
automatically. Auto configuration only works in RGB-PC
mode.
Transmission [ j ][u][ ][Set ID][ ][Data][Cr]
Data 01: To set
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
21. Channel Tuning (Command: m a)
To tune channel to following physical/major/minor
number.
(This feature is not available for all models.)
Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
ENGLISH
ENG
Digital channels have a Physical, Major, and Minor
channel number. The Physical number is the actual
digital channel number, the Major is the number that the
channel should be mapped to, and the Minor is the subchannel. Since the ATSC tuner automatically maps the
channel to the Major number, the Physical number is not
required when sending a command.
Data 00: Physical Channel Number
NTSC air: 02~45, NTSC cable: 01, 0E~7D
ATSC air: 01~45, ATSC cable: 01~87
Data 01 & 02: Major Channel Number
Data 01: High byte Data 02: Low byte
Two bytes are available for the Major and Minor,
normally only the second byte is used.
Data 03 & 04: Minor Channel Number
Not needed for NTSC.
The table lists the binary code which must be converted
to Hexadecimal before sending. For example:
The binary code to tune the sub source to an NTSC cable
channel is “1000 0001”, which translates to “81” in
Hex.
* 7th bit : For which source do you want to change
the channel.
* 6th bit: Use a two part or one part channel. Most
cases just use 0 since it’s ignored when using
NTSC.
* 5th bit: Use 0 with NTSC since it can only use
the physical channel number. Normally use 1 for
ATSC since most times it doesn’t matter what the
physical number is.
* 4th bit: Set to 0.
* 3-0 bits: Choose signal type.
* Tune Command Examples:
1. Tune to the analog (NTSC) cable channel 35.
Data 00 = Physical of 35 = 23
Data 01 & 02 = No Major = 00 00
Data 03 & 04 = No Minor = 00 00
Data 05 = 0000 0001 in binary = 01
Total = ma 00 23 00 00 00 00 01
2. Tune to the digital (ATSC) local channel 30-3.
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03
Data 05 = 0010 0010 in binary = 22
Total = ma 00 00 00 1E 00 03 22
22. Channel Add/Del (Command: m b)
To add and delete the channels.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00: Channel Delete Data 01: Channel Add
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
23. Key (Command: m c)
To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
See page 3.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
When TV is in the standby mode, TV will turn on by
POWER button of remote control only.
EXTERNAL CONTROL DEVICE SETUP
11
* Table List (Channel Tuning)
7
Main/Sub
Picture
6
Two/One
Part
Channel
5
Using
Physical
Channel
4
Reserved
3
2
1
0
Step
0
Main
0
Two
0
Use
x
0
0
0
0
NTSC Air
1
Sub
1
One
1
No Use
x
0
0
0
1
NTSC Cable
x
0
0
1
0
ATSC Air
x
0
0
1
1
ATSC Cable_std
x
0
1
0
0
ATSC Cable_hrc
x
0
1
0
1
ATSC Cable_irc
x
0
1
1
0
ATSC cable_auto
x
0
1
1
1
Reserved
x
x
x
x
x
...
x
1
1
1
1
Reserved
ENG
ENGLISH