DeLonghi 5713214281 Coffeemaker User Manual

5713214281/07.10
BEAN TO CUP ESPRESSO AND
CAPPUCCINO MACHINE
DE
GB
ESAM 04.320
Electrical requirements
Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you are in any doubt about your supply
contact your local electricity company.
The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.
Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the procedure outlined below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children might find it and plug it into a supply
socket - with the obvious consequent danger.
N.B. We recommend the use of good quality plugs and wall sockets that can be switched off when the machine is not in use.
important: the wires in the mains lead fitted to this appliance are coloured in accordance with the following code:
Green and Yellow to Earth
green and yellow earth
blue neutral
brown
live
13 amp Fuse
Brown to live
Blue to
neutral
Cord Clamp
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as
follows:
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol
or
coloured green or green and yellow.
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead clamp on the plug. If your electricity
supply point has only two pin socket outlets, or if you are in doubt, consult a qualified electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible
cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be refitted. If the fuse cover is lost, the plug must not be used until a replacement cover is obtained. The
colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse recess or elsewhere on the plug. Always state this colour when ordering
a replacement fuse cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362 should be fitted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
Warning - this appliance must be earthed
2
A
A3 A4 A5
A6
A7
A2
A1
A8
A22
A10
A21
A9
A20
A11
A12
A19
A13
A18
A14
A15
A17
A23
B
A16
B1
B2
B3
B9
B4
B10
B5
B11
B6
B12
B7
B8
3
1
2
4
5
6
7
8
9
10
11
12
13
14
15
3
4
16
17
18
20
21
22
23
24
25
26
27
28
29
5
19
contents
CLEANING............................................................. 14
Fundamental safety warnings..................................................7
Cleaning the coffee maker......................................................14
Cleaning the coffee grounds container....................................14
Cleaning the drip tray.............................................................14
Cleaning the inside of the machine.........................................15
Cleaning the water tank..........................................................15
Cleaning the coffee spouts......................................................15
Cleaning the pre-ground coffee funnel...................................15
Cleaning the infuser................................................................15
DESIGNATED USE.....................................................7
DESCALING............................................................ 15
INSTRUCTIONS........................................................8
SETTING WATER HARDNESS.................................... 16
INTRODUCTION.......................................................7
Symbols used in these instructions...........................................7
Letters in brackets.....................................................................7
Troubleshooting and repairs.....................................................7
SAFETY...................................................................7
Measuring water hardness......................................................16
Set water hardness.................................................................16
DESCRIPTION..........................................................8
Description of the appliance.....................................................8
Description of control panel .....................................................8
TECHNICAL SPECIFICATION..................................... 16
PRELIMINARY CHECKS.............................................9
disposal.............................................................. 17
Checking the appliance.............................................................9
Installing the appliance............................................................9
Connecting the appliance.........................................................9
Using the appliance for the first time........................................9
DISPLAYED MESSAGES........................................... 18
TROUBLESHOOTING............................................... 19
TURNING THE APPLIANCE ON...................................9
TURNING THE APPLIANCE OFF..................................9
F
t
F
t
F
T
u
MENU SETTINGS.................................................... 10
Descaling................................................................................10
Setting the language .............................................................10
Energy Saving.........................................................................10
Cup warmer............................................................................10
Adjust time.............................................................................10
Auto-Start...............................................................................10
Auto-Off (Stand-by)................................................................11
Setting the temperature.........................................................11
Setting water hardness...........................................................11
Statistics function...................................................................11
Default values (reset)..............................................................11
MAKING COFFEE.................................................... 11
Selecting the coffee taste........................................................11
Selecting the quantity of coffee in the cup . ...........................11
Customising the espresso “my coffee” quantity.......................12
Programming the long “my coffee” quantity ..........................12
Adjusting the coffee mill.........................................................12
Tips for a hotter coffee............................................................12
Making espresso coffee using coffee beans.............................12
Making long coffee using coffee beans...................................13
Making espresso or long coffee using pre-ground coffee........13
MAKING FROTHED MILK (FOR CAPPUCCINO) AND HOT
MILK..................................................................... 13
Making hot milk . ...................................................................14
Cleaning the cappuccino maker after use................................14
HEATING WATER.................................................... 14
Preparation.............................................................................14
6
INTRODUCTION
SAFETY
Thank you for choosing the ESAM04.320 automatic coffee and
cappuccino maker.
We hope you enjoy using your new appliance.
Take a few minutes to read these instructions.
This will avoid all risks and damage to the machine.
Fundamental safety warnings
Danger!
This is an electrical appliance and may cause electric shock.
You should therefore respect the following safety warnings:
• Never touch the appliance with damp hands or feet.
• Never touch the plug with damp hands.
• Make sure the socket used is freely accessible at all times,
enabling the appliance to be unplugged when necessary.
• Unplug directly from the plug only. Never pull the power
cable as you could damage it.
• To disconnect the appliance completely, place the main
switch at the back of the appliance in the 0 position (fig.
6).
• If the appliance is faulty, do not attempt to repair. Turn it
off, unplug from the mains socket and contact Customer
Services.
• If the plug or power cable is damaged, it must be replaced
by De’Longhi Customer Services only to avoid all risk.
Symbols used in these instructions
Important warnings are identified by these symbols.
These warnings must absolutely be respected.
Danger!
Failure to observe the warning could result in possibly life
threatening injury from electric shock.
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Danger of burns!
Failure to observe the warning could result in scalds or burns.
Please note :
This symbol identifies important advice or information for the
user.
•
Letters in brackets
The letters in brackets refer to the legend in the Description of
the appliance on page 3.
•
Troubleshooting and repairs
In the event of problems, first try and resolve them following
the information given in the sections “Displayed messages” on
page 18 and “Troubleshooting” on page 19.
If this does not resolve the problem or you require further
information, you should consult Customer Services by calling
the number given on the annexed “Customer Service” sheet.
If your country is not among those listed on the sheet, call the
number given in the guarantee.
If repairs are required, contact De’Longhi Customer Services
only.
The addresses are given in the guarantee certificate provided
with the machine.
Important!
Keep all packaging (plastic bags, polystyrene foam) away
from children.
The appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children must be supervised to ensure
they do not play with the appliance.
Danger: Risk of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
DESIGNATED USE
This appliance is designed and made to prepare coffee and heat
drinks. All other use is considered improper. This appliance is
not suitable for commercial use. The manufacturer is not liable
for damage deriving from improper use of the appliance. This is
a household appliance only.
It is not intended for use in:
• staff kitchen areas in shops, offices and other working
environments;
• farm houses;
• by clients in hotels, motels and other residential type
environments;
• bed and breakfast type environments.
7
INSTRUCTIONS
DESCRIPTION
Read these instructions carefully before using the appliance.
• Failure to respect these instructions may result in burns or
damage to the appliance.
The manufacturer is not liable for damage deriving from
failure to respect these instructions.
Description of the appliance
(page 3 - A )
A1.Grinding adjustment knob
A2. Main switch
A3. Beans container
A4. Beans container lid
A5. Cover for funnel and measure compartment
A6. Measure compartment
A7. Cup shelf (cup warmer enabled from settings menu)
A8. Pre-ground coffee funnel
A9. Steam spout
A10. Cappuccino maker (removable)
A11. Cappuccino/hot milk selection ring
A12. Steam nozzle (removable)
A13. Water tank
A14. Power cable
A15. Cup tray
A16.Drip tray
A17. Service door
A18.Grounds tray
A19. Coffee spout (adjustable height)
A20. Coffee guide
A21.Infuser
A22. Control panel
Please note:
Keep these instructions. If the appliance is passed to other
persons, they must also be provided with these instructions.
Description of control panel
(page 3 - B )
A number of buttons on the panel have a dual function. This is
indicated in brackets in the description.
B1.Display: guides the user in using the appliance.
B2. Steam/hot water knob
B3.
button: to deliver two cups of coffee (When
you access the MENU: to change menu items and
parameters)
B4.
button: to make 1 cup of coffee (When you access
the MENU: OK to confirm menu parameters)
B5. MENU button: to access the settings menu.
B6.
button: to turn the appliance on and off (standby)
B7.
button: to select the steam function.
B8. LONG button: to deliver one cup of LONG coffee.
B9.
button: to select coffee quantity (When
you access the MENU: to change menu items and
parameters)
B10.
button: to select coffee taste (When you access
the MENU: ESC to exit the menu)
B11.
button: to perform a rinse cycle
B12.
button: to make 1 cup using pre-ground
coffee
8
W
f
C
C
t
a
PRELIMINARY CHECKS
You must first choose the language (the languages scroll
through at intervals of about 3 seconds).
2. When “English” appears, press the OK button (fig. 2) for a
few seconds until “ENGLISH set” is displayed.
Follow the instructions indicated by the appliance:
3. “FILL TANK”: remove the water tank, fill to the MAX line
with fresh water then replace in the appliance (fig. 3).
4. Turn the cappuccino maker outwards and place a container
with a minimum capacity of 100 ml underneath (fig. 4).
5. “TURN STEAM KNOB” is displayed. When the steam knob
is turned to the I position (fig. 4), “Hot water Press OK” is
displayed.
6. Press the OK button (fig. 2).
“Please wait” is displayed and the appliance begins to
deliver water from the hot water spout.
The appliance ends the first start up procedure, then the
message “Turning off, Please wait” is displayed and the
appliance goes off.
The coffee maker is now ready for normal use.
Checking the appliance
After removing the packaging, make sure the product is
complete and undamaged and that all accessories are present.
Do not use the appliance if it is visibly damaged. Contact
De’Longhi Customer Services.
Installing the appliance
Important!
When you install the appliance, you should respect the
following safety warnings:
• The appliance gives off heat. After positioning the
appliance on the worktop, leave a space of at least 3 cm
between the surfaces of the appliance and the side and
rear walls and at least 15 cm above the coffee maker.
• Water penetrating the appliance could cause damage. Do
not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes. Do not install the appliance in a room where the
temperature could drop below freezing point.
• Arrange the power cable in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces
(e.g. electric hot plates).
•
Please note:
When using the appliance for the first time, you need to
make 4-5 cups of coffee or 4-5 cappuccinos before the
appliance starts to give satisfactory re-sults.
Connecting the appliance
TURNING THE APPLIANCE ON
Important!
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
Please note:
Before turning the appliance on, make sure the main switch on
the back of the appliance is in the I position (fig. 1).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
The appliance is ready for use only after completion of this
cycle.
Danger of burns!
During rinsing, a little hot water comes out of the coffee spouts
and is collected in the drip tray underneath.
Avoid contact with splashes of water.
• To turn the appliance on, press the button (fig. 5).
The message “Heating up, Please wait” is displayed.
After heating, the message “Rinsing” is displayed. As well as
heating the boiler, the appliance also heats the internal circuits
by circulating hot water.
The appliance is at temperature when the message indicating
the taste and quantity of coffee appears.
Using the appliance for the first time
•
•
Please note :
Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of coffee
in the grinder. The machine is, however, guaranteed to be
new.
You should customise water hardness as soon as possible
following the instructions in the section “Setting water
hardness” on page 16.
TURNING THE APPLIANCE OFF
1. Plug the appliance into the mains socket and place the
main switch on the back of the appliance in the I position
(fig. 1).
Each time the appliance is turned off, it performs an automatic
rinse cycle which cannot be interrupted.
9
Important!
To avoid damaging the appliance, always press the
button (fig. 5) to turn off.
•
•
Danger of burns!
During rinsing, a little hot water flows from the coffee spouts.
Avoid contact with splashes of water.
Cup warmer
This function enables the cup warmer to be enabled or disabled.
Proceed as follows:
1. Press the MENU button to enter the settings menu.
2. Press the or button until “Cup warmer” is displayed;
3. Press the OK button. “Enable?” is displayed (or “Disable?”
if the function has already been enabled).
4. Press the OK button to enable or disable the func-tion or
the ESC button a number of times to exit the menu.
Warming the cups keeps the coffee hot.
To turn the appliance off, press the
button (fig. 5). The
appliance performs a rinse cycle then goes off.
Please note:
If the appliance is not used for an extended period, place the
main switch in the 0 position (fig. 6).
Never place the main switch in the 0 position while the
appliance is on.
MENU SETTINGS
When you access the settings menu by pressing the MENU
button, the following menu items can be selected: Descale,
Set language, Energy saving, Cup warmer, Adjust time, Autostart, Auto-off, Set temperature, Water hardness, Statistics,
Default values.
Adjust time
To adjust the time on the display, proceed as follows:
1. Press the MENU button to enter the settings menu.
2. Press the or button until “Adjust time” is displayed;
3. Press the OK button. The hours flash on the display;
4. Press the or button to change the hours;
5. Press the OK button to confirm. The minutes flash on the
display;
6. Press the or button to change the minutes;
7. Press the OK button to confirm;
8. Press the ESC button to exit the settings menu.
Descaling
For instructions on descaling, see page 15.
Setting the language
To modify the language of the display, proceed as follows:
1. Press the MENU button to enter the settings menu.
2. Press the
or
button until “Set language” is
displayed;
3. Press the OK button;
4. Press the or button until the required language is
displayed;
5. Press the OK button to confirm;
6. Press the ESC button exit the menu.
Energy Saving
Use this function to enable or disable “Energy saving” mode.
When enabled, the function reduces energy consumption in
compliance with European regulations.
To enable or disable the function, proceed as follows:
1. Press the MENU button to enter the settings menu.
2. Press the or
button until “Energy saving” is
displayed;
3. Press the OK button. “Disable?” is displayed (or “Enable?”
if the function has already been disabled).
4. Press the OK button to disable or enable the func-tion or
the ESC button a number of times to exit the menu.
When the function is active, if the machine is not used for
about 1 minute, “Energy saving” is displayed.
Please note!
To exit the “Energy saving” mode, first press a button, then
press the button relative to the desired drink.
A few seconds may elapse between “Energy saving” mode
and delivery of the first drink; “Preparation underway...” is
displayed.
Please note!
The display shows the time when the appliance is in stand-by
ro the energy saving mode is enabled: if the time is not set, the
display shows “0:00” blinking.
Auto-Start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Please note!
To enable this function, the time must be set correctly.
To enabled Auto-on, proceed as follows:
1. Press the MENU button to enter the settings menu.
2. Press the or button until “Auto-start” is displayed;
3. Press the OK button. “Enable?” is displayed;
4. Press the OK button. The hours flash on the display;
5. Press the or button to select the hours;
6. Press the OK button to confirm. The minutes flash on the
display;
7. Press the or button to change the minutes;
10
- how many times the machine has been descaled.
- the total number of litres of water delivered.
5. Press the ESC button twice to exit the menu.
8. Press the OK button to confirm. The
symbol appears
under “Auto-start” on the display.
9. Press the ESC button to exit the menu. When the appliance
is in stand-by, the
symbol appears next to the clock
to indicate that auto-start has been programmed.
To disable the function:
1. Press the MENU button to enter the settings menu.
2. Press the or button until “Auto-start” is displayed;
3. Press the OK button. “Disable?” is displayed;
4. Press the OK button to confirm;
5. Press the ESC button to exit the menu. When the appliance
is in stand-by, the
symbol is no longer displayed.
Default values (reset)
This resets all menu settings and programmed quantities back
to the default values (with the ex-ception of the language
which remains as set).
1. Press the MENU button to enter the menu;
2. Press the
or
button until “Default values” is
displayed;
3. Press the OK button;
4. The message “Confirm?” is now displayed.
5. Press the OK button to confirm and exit.
Auto-Off (Stand-by)
The appliance is set by default to go off if not used for two
hours.
The time can be changed so that the appliance switches off
after 15 or 30 minutes, or after 1, 2 or 3 hours.
To re-programme Auto-off, proceed as follows:
1. Press the MENU button to enter the settings menu.
2. Press the or button until “Auto-off” is displayed;
3. Press the OK button;
4. Press the or button until the required time (15 or 30
minutes, or 1, 2 or 3 hours) is displayed;
5. Press the OK button to confirm;
6. Press the ESC button exit the menu.
Auto-off is programmed.
MAKING COFFEE
Please note!
A few seconds may elapse between “Energy saving” mode and
delivery of the first coffee.
Selecting the coffee taste
The appliance is set by default to make coffee with a standard
taste.
You can also choose one of these tastes:
Extra-mild taste
Mild taste
Standard taste
Strong taste
Extra-strong taste
Setting the temperature
To modify the temperature of the water used to make the
coffee, proceed as follows:
1. Press the MENU button to enter the settings menu.
2. Press the or
button until Set temperature” is
displayed;
3. Press the OK button;
4. Press the or button until the required temperature is
displayed (l = low; llll = high);
5. Press the OK button to confirm;
6. Press the ESC button exit the menu.
To change the taste, press the
button (fig. 7)
repeatedly until the required taste is displayed.
Selecting the quantity of coffee in the cup
The appliance is set by default to make a standard quantity of
coffee.
button (fig.
To select the quantity of coffee, press the
8) repeatedly until the message corresponding to the required
quantity of coffee is displayed:
Corresponding
coffee
Setting water hardness
For instructions on setting water hardness, see page 16.
Statistics function
This displays statistics relating to the machine. To display,
proceed as follows:
1. Press the MENU button to enter the settings menu.
2. Press the or button until “Statistics” is displayed;
3. Press the OK button;
4. Press the or button, you can check:
- how many coffees have been made;
11
espresso
(ml)
LONG COFFEE
(ml)
MY COFFEE
program.
from 20 to 180
program. from
20 to 250
SHORT
≃40
≃ 125
STANDARD
≃60
≃ 175
LONG
≃90
≃ 210
EXTRA LONG
≃120
≃ 250
Customising the espresso “my coffee” quantity
The appliance is set by default to automatically deliver 30 ml of
espresso “MY COFFEE”.
To modify these settings, proceed as follows:
1. Place a cup under the coffee spouts ( fig. 10).
2. Press the
button repeatedly (fig. 8) until “MY
COFFEE” is displayed.
3. Keep the
button (fig. 2) pressed until the message
“Program quantity” is displayed. Release the button. The
machine starts making the coffee;
4.As soon as the coffee in the cup reaches the required level,
press the
button again.
The quantity set has now been programmed.
Tips for a hotter coffee
For a hotter coffee, you are recommended to:
• before delivering the coffee, perform a rinsing cycle by
pressing the
button to select the “Rinsing” function.
Hot water is delivered from the spout, heating the internal
circuits of the appliance and thus raising the coffee
temperature.
• If “Cup warmer” mode has been enabled, place the cups
on the cup warmer until they are warm.
• warm the cups by rinsing them with hot water (us-ing the
hot water function);
• set the “high” coffee temperature (llll) in the
menu.
Programming the long “my coffee” quantity
The appliance is set by default to automatically deliver about
100ml of LONG “MY COFFEE”. To modify this quantity, proceed
as follows:
1. Place a cup under the coffee spouts ( fig. 16).
2. Press the
button repeatedly (fig. 8) until “MY
COFFEE” is displayed.
3. Keep the LONG button (fig. 9) pressed until the message
“Program quantity” is displayed. Release the button. The
machine starts making the coffee;
4.As soon as the coffee in the cup reaches the required level,
press the LONG button again.
The quantity set has now been programmed.
Making espresso coffee using coffee beans
M
W
c
Important!
Do not use caramelised or candied coffee beans as they could
stick to the coffee mill and make it unusable.
1. Fill the container with coffee beans (fig. 12).
2. Place under the coffee spouts:
- 1 cup, if you want to make 1 coffee (fig. 10);
- 2 cups, if you want 2 coffees (fig. 13);
3.Lower the spouts as near as possible to the cup. This makes
a creamier coffee (fig. 14).
4. Press the button corresponding to the number of coffees
required (1 cup
or 2 cups
) (fig. 2 and 15).
5. Preparation begins. The quantity and taste of coffee
selected is displayed together with a progress bar which
gradually fills as preparation progresses.
Once the coffee has been made, the appliance pre-pares for
use again.
Adjusting the coffee mill
The coffee mill is set by default to prepare coffee correctly and
should not require regulating initially.
However, if after making the first few coffees you find that
delivery is either too fast or too slow (a drop at a time), this
can be corrected by adjusting the grinding adjustment knob
(fig. 11).
Please note:
While the machine is making coffee, delivery can be
interrupted at any moment by pressing one of the coffee
buttons (
or
).
• At the end of delivery, to increase the quantity of coffee
in the cup, just press (within 3 seconds) one of the coffee
buttons (
or
).
Once the coffee has been made, the appliance is ready to use
again.
•
Please note!
The grinding adjustment knob must only be turned when the
coffee mill is in operation.
For faster delivery (not a drop at
a time), turn one click clockwise
towards “7” (coarser ground coffee).
For fuller bodied creamier coffee,
turn one click anticlockwise towards
“1” (finer ground coffee).
Important!
If the coffee is delivered a drop at a time, too fast and not creamy
enough or too cold, read the tips in the “Troubleshooting”
section on page 19.
Various alarm messages could be displayed while using the
machine. Their meaning is explained in the section “Displayed
messages” (page 18).
These adjustments will only be evident after at least 2 cups of
coffee have been delivered.
If delivery is still too fast or too slow, repeat the correction,
turning the knob another click.
12
M
•
Making long coffee using coffee beans
fills as preparation progresses.
Once the coffee has been made, the appliance prepares for use
again.
Please note!
When this function is enabled, a long coffee similar to drip
coffee is obtained.
MAKING FROTHED MILK (FOR CAPPUCCINO)
AND HOT MILK
Important!
Do not use caramelised or candied coffee beans as they could
stick to the coffee mill and make it unusable.
Please note!
A few seconds may elapse between “Energy saving” mode
and delivery of the first drink; “Preparation underway...” is
displayed.
1. Fill the container with coffee beans (fig. 12);
2. Adjust the height of the spout according to the cup used.
Put the cup for long coffee under the spouts (fig. 16);
3. Press the LONG button (fig. 9). Preparation begins.
A progress bar appears on the display and gradually
advances as the procedure progresses.
Once the coffee has been made, the appliance pre-pares for
use again.
•
•
•
Important! Danger of burns
During preparation, steam is given off. Take care to avoid
scalds.
1. When preparing cappuccino, make the coffee in a large
cup;
2. Fill a container with about 100 grams of milk for each
cappuccino to be made. In choosing the size of the
container, bear in mind that the milk doubles or triples in
volume;
Please note:
While the machine is making coffee, delivery can be
interrupted at any moment by pressing the LONG button.
Only one cup of long coffee can be made at a time.
When delivering more than 125 ml, the appliance
automatically grinds more coffee halfway through
delivery.
Making espresso or long coffee using pre-ground coffee
•
•
3.
Important!
Never add pre-ground coffee when the machine is off or it
could spread through the inside of the machine and dirty
it. This could damage the appliance.
Never use more than one level
measure or it could dirty the inside
of the machine or block the funnel.
4.
5.
6.
Please note!
If you use pre-ground coffee, you can only make one cup of
coffee at a time.
7.
1. Press the
button. “Pre-ground” flashes on the
display.
2. Make sure the funnel is not blocked, then add one level
measure of pre-ground coffee (fig. 17)
3. Place a cup under the coffee spouts.
4. To make espresso coffee, press the 1 cup
button (fig.
2). To make long coffee, press the LONG button (fig. 9).
5. Preparation begins. The amount of coffee selected is
displayed together with a progress bar which gradually
8.
Please note:
For a richer denser froth, use skimmed or partially
skimmed milk at refrigerator temperature (about 5°C).
To avoid milk with poor froth or large bubbles, always
clean the cappuccino maker as described in the section
“Cleaning the cappuccino maker after use”.
Make sure the ring on the cappuccino maker is in the
“CAPPUCCINO” position (fig. 18).
Press the
button. “Heating up Please wait” is
displayed, followed after a few seconds by “TURN STEAM
KNOB”.
Turn the cappuccino maker outwards and immerse it in
the milk container (fig. 19). Take care not to immerse the
black ring;
Turn the steam knob to the I position (fig. 4). Steam
is delivered from the cappuccino maker, giving the
milk a creamy frothy appearance and making it more
voluminous;
For a creamier froth, rotate the container with slow
movements in an upward direction. (You should not
discharge steam for more than 3 minutes at a time);
When you have obtained the required froth, stop
steam delivery by turning the steam knob back to the 0
position.
Important! Danger of burns
Always turn the steam knob to the 0 position before removing
the container with the frothed milk to avoid burns caused by
splashes of boiling milk.
13
CLEANING
9. Add the milk froth to the cup of coffee prepared previously.
The cappuccino is ready. Sweeten to taste and, if desired,
sprinkle the froth with a little cocoa powder.
•
Making hot milk
To make hot milk without froth, proceed as described in the
above section, making sure the ring on the cappuccino maker
is positioned upwards in the “HOT MILK” position.
•
•
Cleaning the cappuccino maker after use.
Clean the cappuccino maker each time you use it to avoid the
build-up of milk residues or blockages.
Cleaning the coffee maker
The following parts of the machine must be cleaned regularly:
- coffee grounds container (A18),
- drip tray (A16),
- the inside of the machine, accessible after opening the
service door (A19),
- water tank (A13),
- coffee spouts (A20) and hot water nozzle (A11),
- pre-ground coffee funnel (A8),
- infuser (A12)
Important! Danger of burns
When cleaning the cappuccino maker, a little hot water is
delivered.
Avoid contact with splashes of water.
1. Deliver a little water for a few seconds by rotating the
steam knob to the I position. Then turn the steam knob to
the 0 position to stop the flow of hot water.
2. Wait for a few minutes for the cappuccino maker to
cool down, hold the handle of the cappuccino tube in
one hand and with the other rotate the cappuccino
maker anticlockwise (fig. 20) then remove by pulling
downwards.
3. Remove the ring upwards (fig. 21).
4. Wash all parts of the cappuccino maker thoroughly with
warm water.
5. Make sure the two holes shown by the arrow in fig. 22 are
not blocked. If necessary, clean with a pin.
6. Replace the inner section by inserting it carefully onto the
adjustable tube, then insert the steam nozzle and turn
anticlockwise to lock it in place.
Cleaning the coffee grounds container
When “EMPTY GROUNDS CONTAINER” is displayed, the grounds
container must be emptied and cleaned.
Until the grounds container has been cleaned, the appliance
continues to display the message and coffee cannot be made.
Even if not full, the empty grounds container message is
displayed 72 hours after the last coffee has been prepared. For
the 72 hours to be calculated correctly, the machine must never
be turned off with the main switch in the 0 position.
To clean (with the machine on):
• Open the service door on the front of the appliance (fig.
23), extract the drip tray (fig. 24), empty and clean.
• Empty the grounds container and clean thoroughly to remove all residues left on the bottom.
HEATING WATER
Please note:
A few seconds may elapse between “Energy saving” mode and
delivery of hot water; “Preparation underway...” is displayed.
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds.
If this is not done, when you make the next coffees, the
grounds container may fill up more than expected and clog the
machine.
Preparation
Important! Danger of burns.
Never leave the machine unsupervised while delivering hot
water. The hot water spout becomes hot while water is being
delivered and must be handled by the handle only.
1. Place a container or cup under the cappuccino maker (as
close as possible to avoid splashes) (fig. 4).
2. Turn the steam knob to the I position (fig. 4). “Hot water”
is displayed and delivery begins.
3. Stop by turning the steam knob to the 0 position.
Important!
Do not use solvents, abrasive detergents or alcohol to
clean the appliance. With De’Longhi superautomatic
coffee makers, you need not use chemical products to
clean the machine.
None of the components can be washed in a dishwasher.
Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces.
Cleaning the drip tray
Important!
If the drip tray is not emptied regularly, the water could overflow
from the edge and seep inside or around the machine.
This could damage the machine, the surface it rests on or the
surrounding area.
14
T
l
B
m
T
B
o
s
C
C
C
T
The drip tray is fitted with a level indicator (red) showing the
level of water it contains (fig. 24).
Before the indicator protrudes from the cup tray, the drip tray
must be emptied and cleaned.
To remove the drip tray:
1. Open the service door (fig. 23);
2. Remove the drip tray and the grounds container (fig. 25);
3. Empty the drip tray and grounds container (A18) and
wash them;
4. Replace the drip tray complete with grounds container;
5. Close the service door.
Important!
RINSE WITH WATER ONLY
NO WASHING UP LIQUID - NO DISH WASHER
Do not use washing up liquid to clean the infuser as it could
cause damage.
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
6.After cleaning, replace the infuser by sliding it onto the
internal support and pin at the bottom, then push the
PUSH symbol fully in until it clicks into place.
Cleaning the inside of the machine
Danger of electric shock!
Before cleaning internal parts, the machine must be turned
off (see “Turning off”) and unplugged from the mains power
supply. Never immerse the coffee maker in water.
1. Check regularly (about every 100 coffees) that the inside
of the appliance (accessible after removing the drip tray)
is not dirty. If necessary, remove coffee deposits with the
brush or a sponge.
2.Remove the residues with a vacuum cleaner (fig. 26).
Please note!
If the infuser is difficult to insert,
you must first adapt it to the right
dimensions by pressing it
forcefully from the bottom and
top as shown in the figure.
Cleaning the water tank
1. Clean the water tank (A13) regularly (about once a month)
with a damp cloth and a little mild washing up liquid.
2. Clean to remove all washing up liquid residues, then rinse
the water tank thoroughly.
7. Once inserted, make sure the two red
buttons have snapped out.
8.Replace the drip tray and waste coffee
container.
9. Close the service door.
Cleaning the coffee spouts
1. Clean the coffee spouts with a sponge or cloth (fig. 27).
2. Check the holes in the coffee spout are not blocked. If
necessary, remove coffee deposits with a toothpick (fig.
28).
DESCALING
Descale the machine when the message “DESCALE” flashes on
the display.
Cleaning the pre-ground coffee funnel
Check regularly (about once a month ) that the pre-ground
coffee funnel (A8) is not blocked.
If necessary, remove coffee deposits with a brush.
Important!
Descaler contains acids which may irritate the skin and eyes.
It is vital to respect the manufacturer’s safety warnings given on
the descaler pack and the warnings relating to the procedure to
follow in the event of contact with the skin and eyes.
Cleaning the infuser
The infuser (A12) must be cleaned at least once a month.
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned off (see Turning
off).
2.Open the service door (fig. 23).
3.Extract the drip tray and the grounds container (fig. 25).
4. Press the two red release buttons inwards and at the same
time pull the infuser outwards (fig. 29).
Please note!
Use De’Longhi descaler only. Under no circumstances should
you use sulphamic or acetic based descalers. Their use
invalidates the guarantee. Failure to descale the appliance as
described above also invalidates the guarantee.
15
SETTING WATER HARDNESS
1.Accendere la macchina.
2. Press the MENU button to enter the settings menu. Press
the or button until “Descale” is displayed;
3. Press the OK button. “Descale Confirm?” is displayed. Press
OK to enable the function.
4. The message “Add descaler Press OK” is displayed.
5. Before confirming, empty the water tank (A13).
Pour the descaler diluted with water (respecting the
proportions indicated on the descaler pack) into the water
tank and replace the tank in the appliance.
6. Place an empty container with a minimum capacity of 1.5
litres under the hot water spout.
The DESCALE message is displayed after a period of time
established according to water hardness.
The machine is set by default for a hardness value of 4 (very
hard water).
The machine can also be programmed according to the actual
hardness of the mains water in the various regions, varying the
frequency with which the message is displayed.
Measuring water hardness
1. Remove the “TOTAL HARDNESS TEST” indicator paper from
its pack.
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
Important! Danger of burns
Hot water containing acid flows out of the hot water spout.
Avoid contact with splashes of water.
7. Confirm with the OK button.
8. “TURN STEAM KNOB” is displayed.
9. After turning the knob to the I position (fig. 4), “Descale
Press OK” is displayed.
10. After confirming by pressing OK, the message “Descale
underway” is displayed.
The descale programme starts and the descaler liquid
comes out of the water spout.
The descale programme automatically performs a series
of rinses and pauses to remove limescale deposits from
inside the machine.
After about 30 minutes, “TURN STEAM KNOB” is displayed.
When the steam knob is turned to the 0 position, “Rinsing FILL
TANK” is displayed.
11. The appliance is now ready for rinsing through with
clean water. Remove the water tank, empty, rinse under
running water, fill with clean water and replace. “TURN
STEAM KNOB” is displayed. When the steam knob is
turned to the I position, “Rinsing... Press OK” is displayed.
12.Empty the container used to collect the descaler solution
and replace it under the hot water spout.
13. Press the OK button to start rinsing. Hot water flows out
of the spout and the message “Rinsing... Please wait” is
displayed.
14. When the water tank is completely empty, “TURN STEAM
KNOB” is displayed.
15. When the steam knob is turned to the 0 position, the
appliance goes off.
To use it again, turn the appliance on by pressing the
button.
Level 1 - soft water l
Level 2 - slightly hard water
ll
Level 3 - hard water
lll
Level 4 - very hard water
llll
Set water hardness
1. Press the MENU button to enter the settings menu.
2. Press the or button and select “Water hardness”.
3. Confirm the selection by pressing the OK button.
4. Press the or button to set the water hardness
identified using the indicator paper (see figure in the
previous section).
5. Press the OK button to confirm the setting.
6. Press the ESC button to exit the menu.
The machine is now reprogrammed with the new water
hardness setting.
TECHNICAL SPECIFICATION
Voltage:
220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1350W
Pressure: 15 bar
Water tank capacity: 1,7 l
Size: LxHxD: 282x374x441 mm
Cable length:
1,5 m
Weight: 11,4 Kg
Max. beans container capacity
250 g
16
The appliance complies with the following EC directives:
•
•
•
•
Stand-by Directive no. 1275/2008
Low Voltage Directive 2006/95/EC and subsequent
amendments;
EMC Directive 2004/108/EC and subsequent
amendments
Materials and accessories coming into contact with food
conform to the provisions of EC regulation 1935/2004.
disposal
Important information for correct disposal of the
product in accordance with EC Directive 2002/96/EC.
At the end of its working life, the product must not
be disposed of as urban waste. It must be taken to a
special local authority differentiated waste collection centre or
to a dealer providing this service. Disposing of a household
appliance separately avoids possible negative consequences
for the environment and health deriving from inappropriate
disposal and enables the constituent materials to be recovered
to obtain significant savings in energy and resources.As a
reminder of the need to dispose of household appliances
separately, the product is marked with a crossed-out wheeled
dustbin.
17
DISPLAYED MESSAGES
DISPLAYED MESSAGE
POSSIBLE CAUSE
REMEDY
FILL TANK!
Insufficient water in the tank.
Fill the tank with water and/or insert it correctly, pushing it
as far as it will go until it clicks into place.
GROUND TOO FINE ADJUST
MILL!
Turn steam knob
The grinding is too fine and the coffee is delivered too
slowly or not at all.
When the steam knob has been turned to the I position
as requested by the appliance, press the OK button and
deliver water from the spout until the water flow is regular.
Stop the water flow and repeat coffee delivery, turning the
grinding adjustment knob one click clockwise towards “7”
while the coffee mill is in operation.
If after making at least 2 coffees delivery is still too slow,
repeat the correction procedure, turning the Grinding
adjustment knob another click until delivery is correct.
EMPTY GROUNDS CONTAINER
The grounds container is too full or more than 3 days have
passed since you last made coffee (this guarantees correct
hygiene of the machine).
Empty the grounds container and clean, then replace.
Important: when removing the drip tray, the grounds
container MUST be emptied, even if it contains few
grounds.
If this is not done, when you make the next coffees, the
grounds container may fill up more than expected and clog
the machine.
INSERT GROUNDS CONTAINER
After cleaning, the grounds container has not been
replaced.
Open the service door, remove the drip tray and insert the
grounds container.
ADD PRE-GROUND COFFEE
The “pre-ground coffee” function has been selected
without placing any pre-ground coffee in the funnel.
Place pre-ground coffee in the funnel or deselect the
“pre-ground” function.
DESCALE!
The machine must be descaled.
The descaling procedure described in the “Descaling”
section needs to be performed as soon as possible.
LESS COFFEE!
Too much coffee has been used.
Select a milder taste or reduce the quantity of pre-ground
coffee.
FILL BEANS CONTAINER!
The coffee beans have run out.
Fill the beans container
The pre-ground coffee funnel is clogged.
Empty the funnel with the help of a knife, as described in
the section “Cleaning the pre-ground coffee funnel”.
INSERT INFUSER ASSEMBLY!
The infuser has not been replaced after cleaning.
Insert the infuser as described in the paragraph “Cleaning
the infuser”.
CLOSE DOOR!
The service door is open.
Close the service door.
ADD PRE-GROUND COFFEE
The “pre-ground coffee” function has been selected
without placing any pre-ground coffee in the funnel.
Place pre-ground coffee in the funnel.
The funnel (A8) is blocked.
Empty the funnel with the help of a knife, as described in
the section “Cleaning the pre-ground coffee funnel”.
ADD PRE-GROUND COFFEE
Press OK
A LONG coffee of more than 125 ml has been made with
pre-ground coffee.
Add pre-ground coffee and press OK.
Energy Saving
The function is active and reduces electricity consumption.
Disable the function from the menu (See section “Energy
Saving”).
GENERAL ALARM!
The inside of the appliance is very dirty.
Clean the inside of the appliance thoroughly, as described
in the section “Cleaning and maintenance”. If the message
is still displayed after cleaning, contact a service centre.
18
TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.
PROBLEM
POSSIBLE CAUSE
REMEDY
The coffee is not hot
The cups were not preheated.
Enable the cup warmer, leave the cups at least 20 minutes
to warm up.
Warm the cups by rinsing them with hot water (using the
hot water function).
The coffee is not creamy
enough.
The infuser has cooled down because 2/3 minutes have
elapsed since the last coffee was made.
Before making the coffee, heat the infuser by pressing the
button (see the sections “Tips for a hotter coffee”).
A low coffee temperature is set.
Set a high coffee temperature in the menu.
The coffee is ground too coarsely.
Turn the grinding adjustment knob one click anticlockwise
towards “1” while the coffee mill is in operation (fig. 8).
Continue one click at a time until coffee delivery is
satisfactory. The effect is only visible after delivering 2
coffees.
Wrong type of coffee
Use a type of coffee for espresso coffee makers.
The coffee is delivered too
slowly or a drop at a time.
The coffee is ground too finely.
Turn the grinding adjustment knob one click clockwise
towards “7” while the coffee mill is in operation (fig.
11). Continue one click at a time until coffee delivery is
satisfactory. The effect is only visible after delivering 2
coffees.
The coffee does not come out
of the spouts, but from around
the service door.
The holes in the spouts are clogged with dry coffee dust.
Clean the spouts with a toothpick, sponge or hard bristled
kitchen brush.
The coffee guide inside the service door is blocked and
cannot swing.
Thoroughly clean the coffee guide, particularly near the
hinges.
The coffee is delivered too
quickly.
The coffee is ground too coarsely.
Turn the grinding adjustment knob one click anticlockwise
towards “1” while the coffee mill is in operation (fig. 11).
Avoid turning the grinding adjustment knob excessively
otherwise when you select two cups, the coffee may be
delivered a drop at a time.
Coffee does not come out of
one of the spouts.
The spouts are blocked.
Clean the spouts with a toothpick (fig. 40).
Water comes out of the spouts
instead of coffee.
The pre-ground coffee may be blocked in the funnel (A8).
Empty the funnel with the help of a knife, as described in
the section “Cleaning the pre-ground coffee funnel”.
The milk is not frothed.
The milk is not cold enough or is not semi-skimmed.
You should ideally use skimmed or semi-skimmed milk at
refrigerator temperature (about 5°C).
If the result is not as you wished, try changing brand of
milk.
The ring is not in the “CAPPUCCINO” position.
Push the ring downwards.
The appliance does not come
on.
It is not plugged into the mains socket.
Plug into the mains socket.
The main switch is not turned on.
Place the main switch in the I position (fig. 29).
The LONG coffee has too much
froth
The coffee is ground too finely.
Turn the Grinding adjustment knob one click clockwise
towards “7” while the coffee mill is in operation (fig. 11).
Continue one click at a time until coffee delivery is
satisfactory.
The effect is only visible after delivering 2 coffees.
19
Download PDF

advertising