DeLonghi DE 91 MPS Oven User Manual

INSTALLATION and SERVICE INSTRUCTIONS
USE and CARE INSTRUCTIONS
DE 91 MPS
MULTIFUNCTION
BUILT-IN OVEN
distributed by
DèLonghi
Pty Ltd
Dear Customer,
Thank you for having purchased and given your
preference to our product.
The safety precautions and recommendations reported
below are for your own safety and that of others. They
will also provide a means by which to make full use of
the features offered by your appliance.
Please keep this booklet in a safe place. It may be
useful in future, either to yourself or to others in the
event that doubts should arise relating to its operation.
This appliance must be used only for the task it has
explicitly been designed for, that is for cooking
foodstuffs. Any other form of usage is to be considered
as inappropriate and therefore dangerous.
The manufacturer declines all responsibility in the
event of damage caused by improper, incorrect or
illogical use of the appliance or be faulty installation.
PRODUCT LABEL
This oven has been designed and constructed in accordance with the following codes
and specifications:
AS/NZS 60335-1
General Requirements for Domestic electrical appliances
AS/NZS 60335-2-6 Particular Requirements for Domestic electrical cooking appliances
2
AS/NSZ 1044
Electromagnetic Compatibility Requirements.
CONTENTS
Precautions and recommendations ................................................”
3-4
Installation......................................................................................”
5
Use and care .................................................................................”
Cooking with multifunction oven ...............................................”
Clock/Timer with “Touch control” keys........................................”
11
16
24
Cleaning and maintenance............................................................”
27
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FOR
USE OF ELECTRICAL APPLIANCES
Use of any electrical appliance implies the necessity to follow a series of fundamental rules. In particular:
■ Never touch the appliance with wet hands or feet;
■
Do not operate the appliance barefooted;
The appliance is not intended for use by young children or infirm persons
without supervision;
■ Young children should be supervised to ensure they do not play with the
appliance.
The manufacturer cannot be held responsible for any damages caused by improper,
incorrect or illogical use of the appliance.
■
USING THE OVEN FOR THE FIRST TIME
You are advised to carry out the following operations:
Furnish the interior of the oven.
■ Switch the empty oven ON at maximum temperature for about two hours to
eliminate traces of grease and smell from the components.
■ Let the oven cool down, switch off the electrical supply, then clean the inside
of the oven with a cloth soaked in water and neutral detergent and dry
thoroughly.
■
3
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS
After having unpacked the appliance, check to ensure that it is not damaged.
In case of doubt, do not use it and consult your supplier or a professionally qualified technician.
Packing elements (i.e. plastic bags, polystyrene foam, nails, packing straps, etc.) should not be
left around within easy reach of children, as these may cause serious injuries.
■ Do not attempt to modify the technical characteristics of the appliance as this may become
dangerous to use.
■ Do not carry out cleaning or maintenance operations on the appliance without having previously disconnected it from the electric power supply.
■ After use, ensure that the knobs are in the off position.
■
■
■
■
■
■
■
■
■
Fire risk! Do not store flammable material in the oven.
■
Always use oven gloves when removing the shelves and food trays from the oven whilst hot.
Do not hang towels, dishcloths or other items on the appliance or its handle – as this could
be a fire hazard.
Clean the oven regularly and do not allow fat or oils to build up in the oven base or tray.
Remove spillages as soon as they occur.
Do not stand on the open oven door.
Always stand back from the appliance when opening the oven door to allow steam and hot
air to escape before removing the food.
This appliance is for domestic use only.
Safe food handling: leave food in the oven for as short a time as possible before and after
cooking. This is to avoid contamination by organisms which may cause food poisoning. Take
particular care during warmer weather.
The manufacturer declines all liability for injury to persons or damage to property caused by
incorrect or improper use of the appliance.
■
■
■
■
■
■
■
■
■
4
During and after use of the appliance, certain parts will become very hot. Do not touch hot
parts. Care should be taken to avoid touching heating elements inside the oven.
Household appliances are not intended to be played with by children.
Keep children away from the oven during use.
Children, or persons with a disability which limits their ability to use the appliance, should
have a responsible person to instruct them in its use. The instructor should be satisfied that
they can use the appliance without danger to themselves or their surroundings.
Some appliances are supplied with a protective film on steel and aluminium parts. This film
must be removed before using the appliance.
Make sure that electrical cables connecting other appliances in the proximity of the oven do
not become entrapped in the oven door.
Do not line the oven walls with aluminium foil. Do not place baking trays or the drip tray
on the base of the oven chamber.
WARNING When correctly installed, your product meets all safety requirements laid down
for this type of product category. However special care should be taken around the rear or
the underneath of the appliance as these areas are not designed or intended to be touched
and may contain sharp or rough edges, that may cause injury.
WARNING: Taking care NOT to lift the oven by the door handle.
IMPORTANT NOTE: This appliance shall not be used as a space heater,
especially if installed in marine craft or caravans.
INSTALLATION
CAUTION:
■
■
■
■
■
This appliance must be installed in accordance with these installation
instructions.
This appliance shall only be serviced by authorized personnel.
This appliance is to be installed only by an authorised person.
Incorrect installation, for which the manufacturer accepts no responsibility, may cause personal injury or damage.
Always disconnect the oven from mains power supply before carrying
out any maintenance operations or repairs.
ELECTRICAL REQUIREMENTS
■
■
■
■
■
■
■
■
N.B.
The oven is supplied without a power supply plug and therefore if you are
not connecting directly to the mains, a standardized plug suitable for the
load must be fitted.
Connection to the mains must be carried out by qualified personnel in
accordance with current regulations.
The appliance must be connected to the mains checking that the voltage
corresponds to the value given in the rating plate and that the electrical
cable sections can withstand the load specified on the plate.
The plug must be connected to an earthed socket in compliance with safety
standards.
The appliance can be connected directly to the mains placing a two pole
switch with minimum opening between the contacts of 3 mm between the
appliance and the mains.
The power supply cable must not touch the hot parts and must be
positioned so that it does not exceed 75°C at any point.
Once the appliance has been installed, the switch or socket must always be
accessible.
If the supply cord is damaged it must be replaced by the
manufacturer or its Service Agent or a similarly qualified person in
order to avoid a hazard.
• The connection of the appliance to earth is mandatory.
• For connection to the mains, do not use adapters, reducers or
branching devices as they can cause overheating and burning.
If the installation requires alterations to the domestic electrical system call a qualified
electrician. He should also check that the socket cable section is suitable for the power
drawn by the appliance.
5
REPAIRS
REPLACING THE POWER SUPPLY CABLE
■
■
■
Unhook the terminal board cover by inserting a screwdriver into the two
hooks A (fig. 2).
Open the cable gland by unscrewing screw F (fig. 3), unscrew the terminal
screws and remove the cable.
The new supply cable, of suitable type and section, is connected to the
terminal board following the diagram of fig. 1.
FEEDER CABLE SECTION TYPE HO5RR-F
~
240 V ~
230 V
3050 W (13.26 A)
3 x 1,5 mm2
3320 W (13.83 A)
3 x 1,5 mm2
Figure 1
220 - 240 V
L1
N (L2 )
E
Figure 2
Figure 3
F
A
6
ELECTRIC DIAGRAM
Figure 4
F1
TM
TL
TL1
PR
LF
S1
S2
C
G
S
CIR
V
Oven switch
Oven thermostat
Thermal overload (N.C.)
Thermal overload (N.O.)
Electronic programmer
Oven lamps
Thermostat pilot lamp
Line pilot lamp
Top element
Grill element
Bottom element
Circular element
Fan motor
CF
GIR
M
MT
T
Cooling fan motor
Rotisserie
Terminal block
Testing block
Earth connection
7
FITTING REQUIREMENTS
The appliance should be installed by a QUALIFIED INSTALLATION TECHNICIAN.
The appliance must be installed in compliance with regulations in force.
The walls surrounding the oven must be made of heat-resistant material.
WARNING: Taking care NOT to lift the oven by the door handle.
The oven can be fitted in
standard units, width 90
cm and depth 60 cm.
Installation requires a compartment as illustrated in
figures 5 and 6.
On the lover side, the
oven must lay on supports
standing the oven weight.
min.
860
480
467
478
853
m
896
54
22
min.
900
min.
860
480
467
478
853
m
896
54
22
Figure 6
8
4
0
55
in.
5
in.
50
4
Figure 5
WARNING
When correctly installed,
your product meets all
safety requirements laid
down for this type of product category.
However special care
should be taken around
the rear or the underneath
of the appliance as these
areas are not designed or
intended to be touched
and may contain sharp or
rough edges, that may
cause injury.
FIXING THE OVEN
Introduce the oven into the furniture opening and fix it with 4 screws (not supplied)
as figure 7. It is essential that the oven rests on a surface which will support its
weight, as the screw fixing is only complementary.
Adjust the hinges of furniture doors adjacent to the oven to allow a 4-5 mm gap
between the furniture door and the oven frame.
Figure 7
9
Figure 8
OVEN DOOR
LOWER TRIM
AIR FLOW
IMPORTANT:
To avoid damage to the lower trim please note the following instructions.
The lower trim is designed to allow for good air circulation and the correct opening
of the oven door.
To ensure the trim is not damaged due to the appliance being placed on the floor,
the appliance should be suitably supported as in above illustration.
After installation the appliance door should be slowly opened to ensure no damage
has occurred.
No responsibility for lower trim damage will be accepted if these instructions have not been followed.
10
USE and CARE
CAUTION:
■
This appliance must be used only for the task it has explicitly been designed
for, that is for domestic cooking of foodstuffs. Any other form of usage is to be
considered as inappropriate and therefore dangerous.
■
Do NOT place combustible materials or products on this appliance at any time.
USING THE OVEN FOR THE FIRST TIME
Operate as follows:
Assemble the wire racks on the oven walls using the 2 screws, interposing the
catalytic panels A with the arrow up (fig. 9). The catalytic panel with the hole
for the rotisserie must be positioned on the right oven wall. DO NOT INTERPOSE THE CATALYTIC PANEL WITHOUT THE HOLE ON THE RIGHT OVEN WALL.
■ Slide in the grease filter on the back of the oven as in Fig. 11.
■ Slide in, on the guides, the shelf and the tray (fig. 10). The rack must be fitted
so that the safety catch, which stops it sliding out, faces the inside of the
oven.
■ To eliminate traces of grease in manufacture it is necessary to pre-heat the oven
at the maximum temperature:
• For 60 minutes in the
position, for 30 minutes in the
position and for
another 15 minutes in the
position.
■
Figure 9
HOLE FOR ROTISSERIE
A
A
11
■
■
Unscrew the fixing screws and slide
off the wire racks and the catalytic
liners to the oven wall as in fig. 9.
The grill is secured to the rear wall
of the oven on a hinge system that
allows it to be lowered to allow
proper access when cleaning the
oven ceiling (see next chapter TILTING GRILL).
Let the oven cool down, switch off
the electrical supply, then clean the
inside of the oven with a cloth
soaked in water and neutral detergent and dry thoroughly.
Figure 10
GREASE FILTER
■
■
■
A special screen is provided at the back of the oven to catch grease particles,
mainly when meat is being roasted.
Clean the filter after any cooking! The grease filter can be removed for cleaning
and should be washed regularly in hot soapy water (fig. 11).
Always dry the filter properly before fitting it back into the oven.
CAUTION: When baking pastry etc. this filter should be removed.
Figure 11
12
TILTING GRILL
■
■
(fig. 14)
The grill is secured to the rear wall of the oven on a hinge system that allows it
to be lowered to allow proper access when cleaning the oven ceiling (fig. 14).
In the front the grill is secured to the ceiling by the hooks A and B.
Unlocking the tilting grill (fig. 12)
Locking the tilting grill (fig. 13)
1. Open the hooks A and B.
2. Gently pull down the grill as shown
in the figure 14.
1. Gently lift up the grill.
2. Close the hooks A and B on the grill
bar.
Figure 12
Figure 13
UNLOCKING THE TILTING GRILL
LOCKING THE TILTING GRILL
A-B
1
A-B
2
2
1
Figure 14
A
B
13
TELESCOPIC SLIDING SHELF SUPPORTS
The telescopic sliding shelf supports make it safer and easier to insert and remove the
oven shelf and tray. They stop when they are pulled out to the maximum position.
Important! When fitting the sliding shelf supports, make sure that you fit:
■ The slides to the top wire of a rack. They do not fit on the lower wire.
■ The slides so that they run out towards the oven door.
■ Both sides of each pair of shelf slides.
■ Both sides on the same level.
To fix the sliding shelf support onto the side racks:
■ Screw the side racks onto the oven walls interposing the catalytic panels (fig. 9).
■ Fit the sliding shelf support onto the top wire of a rack and press (Fig. 15). You
will hear a click as the safety locks clip over the wire.
IMPORTANT NOTE: when cooking with the rotisserie DO NOT position
the grill tray on the sliding shelf supports.
Figure 15
Left
Right
14
To remove the telescopic sliding shelf supports:
– Remove the side racks and the catalytic liners by unscrewing the fixing screws
(Fig. 16).
– Lay down the telescopic sliding shelf support and side racks, with the telescopic
sliding shelf support underneath.
– Find the safety locks. These are the tabs that clip over the wire of the side rack
(arrow 1 in Fig. 17).
– Pull the safety locks away from the wire to release the wire (arrow 2 in Fig. 17).
Cleaning the sliding shelf supports
– Wipe the supports with a damp cloth and a mild detergent only.
– Do not wash them in the dishwasher, immerse them in soapy water, or use oven
cleaner on them.
Figure 16
Figure 17
1
2
1
15
Cooking with multifunction oven
Figure 18
Clock and Timer with
“Touch-control” keys
Power on light
Function selector
Temperature light
Thermostat
16
GENERAL FEATURES
With your new Multi-Function oven it is possible to cook a variety of food using the
7 different cooking functions.
These 7 functions are obtained using a combination of the 4 different heating elements plus a defrost function using the fan only.
OPERATING PRINCIPLES
Heating and cooking in the MULTI-FUNCTION oven are obtained in the following
ways:
a. by normal convection
The heat is produced by the upper and lower heating elements.
b. by forced convection
The fan draws in air contained within the oven housing at the rear of the oven
and forces it over the circular heating element. The hot air envelops the food in
the oven givin faster and more even cooking before it is drawn back into the housing to repeat the cycle. It is possible to cook several dishes simultaneously due to
the even distribution of heat within the oven.
c. by semi-forced convection
The heat produced by the top and bottom heating elements is distributed throughout the oven by the fan.
d. by radiant heat
The food is grilled by the infra red grill element.
e. by radiant heat and ventilation
The food is grilled by the grill element and the heat is distributed throughout the
oven
f. by ventilation
The food is defrosted by using the fan only function without heat.
WARNING:
The door is hot, use the handle.
During use the appliance becomes hot. Care should be taken to avoid touching
heating elements inside the oven.
17
Figure 19
Figure 20
THERMOSTAT KNOB (fig. 19)
This only sets the cooking temperature and does not switch the oven on.
Rotate clockwise until the required temperature is reached (from 50 °C to 250 °C).
FUNCTION SELECTOR KNOB (fig. 20)
Rotate the knob clockwise to set the oven for one of the following functions.
OVEN LIGHT
By setting the knob to this position, only the oven lights come on.
They ramain on in all the cooking modes.
TRADITIONAL CONVECTION COOKING
The upper and lower heating elements come on. The heat being dispersed by natural convection. The temperature range must be set between 50 °C and 250 °C
using the thermostat.
The oven must be preheated before cooking.
Ideal for:
Food that requires the same degree of cooking both inside and out, for example
roasts, spare pork ribs, meringues etc.
18
LOWER HEATING ELEMENT
Only the lower element is switched on. Heat is distributed by natural convection.
The thermostat can be set between 50 and 250 °C.
Ideal for:
This mode is particularly suitable to complete cooking of dishes that require higher
temperature at the bottom.
UPPER HEATING ELEMENT
Only the upper element is switched on. Heat is distributed by natural convection.
The thermostat can be set between 50 and 250 °C.
Ideal for:
This mode is particularly suitable to complete cooking of dishes that require higher
temperature at the top.
GRILLING
The infrared grill element at the top of the oven and the rotisserie come on.
The heat is dispersed by radiation.
Use with the oven door closed and the thermostat knob to position between 50 °C
and 225°C maximum.
For cooking hints, see the chapter “USE OF THE GRILL”.
For cooking with the rotisserie, see the chapter “USING THE ROTISSERIE”.
Ideal for:
Intense grilling, browning, cooking au gratin and toasting, cooking with the rotisserie, etc.
19
FAN GRILL
Both the grill and the fan come on. Most of the cooking is done by grilling and then
the hot air circulated around the oven. Use with the oven door closed and the thermostat knob to position between 50 °C and 225°C maximum.
The oven should be preheated for 5 minutes before cooking. For further cooking
hints see “GRILLING AND COOKING AU GRATIN”.
Ideal for:
Quick sealing in of food juices for example such as hamburger, chicken pieces, chops.
MULTI-FUNCTION
The upper and lower heating elements and the fan come on - the heat from the
elements being circulated by the fan.
The temperature range can be set to between 50 °C and 250 °C using the thermostat.
Ideal for:
Large bulky quantities of food that require even cooking throughout for example
large roasts, turkey, roast turkey, cakes etc.
FAN FORCED
The circular element and fan come on. The heat is dispersed by forced convection
and the temperature can be varied to between 50 °C and 250 °C via the thermostat knob. The oven does not require preheating.
Ideal for:
Food which has to be well-cooked outside and soft or rosy inside, for example
lasagne, lamb, roast beef, whole fish etc.
DEFROST
Only the oven fan comes on. Use with the thermostat knob set to “ ” - other temperature have no effect. The food is thawed by ventilation without heating.
20
Ideal for:
Quick thawing of frozen foods; one kg requires approximately 1 hour.
Thawing times vary according to the quantity and type of food to be thawed.
USING THE ROTISSERIE
Figure 21
1. Prepare the rotisserie support
(fig. 21).
• Place the grill tray on the benchtop.
• Insert the supports into the lock
studs.
• Push the supports all the way
down to lock them in firmly.
Lock stud
2. Secure the meat (fig. 22).
Important!
Take care, the forks are sharp!
When securing the meat, ensure
that:
• the skewer goes through the centre of the meat
• the forks hold the meat firmly in
place
• the fork screws are tightened
• there are no loose or projecting
parts. Poultry should be trussed.
Note: the rotisserie can rotate up to
6 kg of meat.
Figure 22
Rotate the fork screws
to loosen and tighten
Fork
Skewer
Figure 23
3. Position the skewer on the support (fig. 23).
• Place the skewer on the support,
and check that the meat does not
touch the grill tray.
• Twist the handle off. It must not be
left in the oven.
4. Place the rotisserie assembly in
the oven (fig. 24).
• Slide the grill tray all the way to
the back on shelf position.
IMPORTANT NOTE: DO NOT
place the grill tray on the sliding
shelf supports (if fitted).
• Push the skewer through the hole
cover on the right-hand wall of the
oven, then insert it fully into the
rotisserie drive hole.
Figure 24
Rotisserie
drive hole
21
COOKING ADVICE
Remember to keep children away from the appliance when you use the grill or oven,
since these parts become very hot.
USE OF THE GRILL
Preheat the oven for about 5 minutes with the door closed.
Introduce the food to be cooked, positioning the rack as close to the grill as possible.
The dripping pan should be placed under the rack to catch the cooking juices
and fats.
GRILLING AND COOKING AU GRATIN
As the hot air completely covers the food to be cooked, grilling may be done with
the food on the rack in the oven. The knob should be switched to position
.
The thermostat should be set to 50 °C and 225°C maximum and the oven pre-heated.
The food should be placed on a rack in the oven for the required cooking time.
Adding a few dabs of butter before the end of the cooking time gives the golden
“au gratin” effect.
Always grill with the oven door closed.
It is recommended that you do not grill for longer than 30 minutes at
anyone time.
Attention: the oven door becomes very hot during operation.
Keep children away.
The external parts of the oven become hot during operation.
Keep children well out of reach.
22
ROASTING
To obtain classical roasting, it is necessary to remember:
• that it is advisable to maintain a temperature between 180 °C and 200 °C.
• that the cooking time depends on the quantity and the type of foods.
SIMULTANEOUS COOKING OF DIFFERENT FOODS
The oven set on position
can cook several different foods together. Foods as
diverse as fish and cakes can be cooked together without the cross transference of
flavours. This is because the fats and cooking smell that would normally be
deposited on the different foods are oxidised and are not absorbed by the foods.
The cooking temperature of the foods, however must be within 20 °C-25 °C of
each other. The food with the longest cooking time will be put into the oven first
and the other foods are added as necessary according to their cooking times.
WARMING BREAD
Set the switch to position
and the thermostat knob to position 150 °C.
Bread becomes fragrant again if wet with a few drops of water and put into the
oven for about 10 minutes at the highest temperature.
STERILIZATION
Sterilization of foods to be preserved, in full and hermetically sealed jars, is done in
the following way:
a. Set the switch to position
.
b. Set the thermostat knob to position 185 °C and preheat the oven.
c. Fill the dripping pan with hot water.
d. Set the jars onto the dripping pan making sure they do not touch each other and
the door and set the thermostat knob to position 135 °C.
When sterilization has begun, that is, when the contents of the jars start to bubble,
turn off the oven and let cool. Check your recycle book for full instructions.
23
Clock/Timer with “Touch control” keys
keys
and
MODE
Figure 25
Touched simultaneously (for
more than 2 seconds):
• setting the clock;
• setting the timer volume
(by touching once, along
with the “MODE” key);
• to cancel automatic cooking at any time.
Function selection (touched
for more than 2 seconds):
• setting the clock (only
after first connection or
after a power failure);
• timer;
• automatic cooking “dur” (duration) - how long the food will take to cook
(by touching the “MODE” key again);
• automatic cooking “End” - the time you would like the oven turns off
(by touching the “MODE” key two more times);
Increases the number shown on the display
Decreases the number shown on the display
Illuminated symbols:
24
AUTO
flashing - automatic cooking completed, oven in automatic position but not set
AUTO
steady illumination - oven set for automatic cooking, cooking still
not taking place
“
”
flashing - timer being set
“
”
steady illumination - timer in operation
“
”
steady illumination - oven set for manual cooking
“
” and AUTO
AUTO flashing - automatic cooking being set
“
” and AUTO
steady illumination - oven set for automatic cooking, cooking taking place.
“TOUCH-CONTROL” KEYS
The “touch-control” keys shall be operated by the fingers (just by touching the key).
When using touch controls it is best to use the ball of your finger rather than the
tip.
The keys are automatically deactivated:
• 8 seconds after the last selection; the deactivation is indicated by an acoustic signal (“beep”).
To reactivate just touch the “MODE” key or the “ ” and “ ” keys (simultaneously)
for more than 2 seconds.
SETTING THE CLOCK
When first connected, or after a power failure, the digits and “AUTO” will shown on
the display. To set the clock, touch the “MODE“ key, for more than 2 seconds, and
then the “ ” or “ ” keys.
Important: the oven does not operate, in manual cooking, without first having set the clock.
To set the clock, with the appliance already connected, touch the “ ” and “ ”
keys simultaneously (for more than 2 seconds), then “ ” or “ ” keys.
Important:
• changing the time will delete any automatic program;
• after setting the clock, the oven starts to operate in the selected function
(manual cooking). The “ ” symbol is steady illuminated.
USING THE TIMER
You can use the timer at any time, even when the oven is not in use.
The timer does not turn the oven off.
The timer can be set for up to 23 hours and 59 minutes.
• To set the timer, touch the “MODE” key for more than 2 seconds (the “ ” symbol flashes), than the “ ” or “ ” keys.
• After about 8 seconds an acoustic signal (“beep”) will sound confirming the regulation (“ ” symbol steady illuminated).
• To check the remaining time touch the “MODE“ key for more than 2 seconds. If
the remaining time is more than a minute the display will show hours and minutes; if less than a minute the display will show seconds.
• When the time is up, the timer will beep. Touch the “MODE” key , for more then
2 seconds, to turn it off; or press the “ ” or “ ” key to stop the beep and than
the “MODE” key, for more than 2 seconds, to deactivate the “ ” symbol flashing
on the display.
• Turn off the oven manually (function and thermostat knobs in the off position) if
the manual cooking has been completed.
25
SETTING THE TIMER VOLUME
You can select from three volume levels.
• Touch the “ ” and “ ” keys simultaneously for more than 2 seconds.
• Touch the “MODE” key; you can read on the display the current timer volume
(“ton1”, “ton2” or “ton3”).
• Touch the “ ” key to listen or change the timer volume.
• Timer volume activated: the last displayed.
• After about 8 seconds an acoustic signal (“beep”) will sound confirming the volume setting; then the time of day will be displayed.
AUTOMATIC COOKING
Use automatic cooking to automatically turn the oven on, cook, and then turn the
oven off.
1. Check the clock shows the correct time.
2. Select the function and temperature (function and temperature knobs). The oven will
come on.
3. Decide how long the food will take to cook, allowing time for preheating if necessary.
4. Touch the “MODE” key for more than 2 seconds and then touch again. “dur” will
show (duration). Using the “ ” and “ ” keys, set the cooking time.
5. Decide the time you would like the oven to turn off; touch the “MODE” key for
more than 2 seconds and then touch it two times again. “End” will show. Using
the “ ” and “ ” keys, set the cooking time.
Note: while “dur” is displayed you can change to “End” just by touching one time
the “MODE” key (within 8 seconds from the last selection).
If there is time to wait before cooking starts, the current time of day and “AUTO” will
show in the clock display. The oven will switch off but is now set for automatic cooking.
If you are already at home to turn the oven on and only want the oven to turn off
automatically, start cooking as normal, then follow step 4 or step 5 to set a time to
stop the oven.
When automatic cooking starts, “ ” will be displayed and the oven will turn on.
• To see the remaining cook time, follow step 4 up to display “dur” (duration).
• To see the set stop time, follow step 5 up to display “End”.
• To cancel automatic cooking at any time, touch the “ ” and “ ” keys simultaneously (for more than 2 seconds) and turn the temperature and function knobs to
the off position.
When the stop time is reached, the oven will turn off, the timer will beep and “AUTO”
will flash:
• Touch any key to stop the beeping.
• Touch the “MODE” key, for more than 2 seconds, to return the oven to the manual mode (“ ” symbol steady illuminated on the display).
• Turn the temperature and function knobs to the off position.
Attention: after a power failure any automatic program is deleted. Turn off
the oven manually.
26
CLEANING and MAINTENANCE
GENERAL ADVICE
■
■
■
■
■
■
Before you begin cleaning, you must ensure that the appliance is
switched off.
It is advisable to clean when the appliance is cold and especially when
cleaning the enamelled parts.
Avoid leaving alkaline or acidic substances (lemon juice, vinegar, etc.) on the
surfaces.
Avoid using cleaning products with a chlorine or acidic base.
Do not use a steam cleaner because the moisture can get into the
appliance thus make it unsafe.
Stainless steel surfaces: clean with a suitable product. Always dry thoroughly.
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door
glass since they can scratch the surface, which may result in shattering of the
glass.
WARNING
When correctly installed, your product meets all safety requirements laid
down for this type of product category. However special care should be
taken around the rear or the underneath of the appliance as these areas
are not designed or intended to be touched and may contain sharp or
rough edges, that may cause injury.
27
ENAMELLED PARTS
All the enamelled parts must be cleaned with a sponge and soapy water only or other
non-abrasive products.
Dry preferably with a microfibre or soft cloth.
STAINLESS STEEL SURFACE
■
CAUTION:
The stainless steel front surfaces (control panel, oven door) used in this oven
are protected with a Special Lacquer to reduce finger-print marks. To avoid
damaging this lacquer, do not clean the stainless steel with abrasive cleaners
or abrasive cloths or scouring pads.
ONLY SOAP/WARM WATER MUST BE USED TO CLEAN THE STAINLESS
STEEL SURFACES.
PAINTED PARTS AND SILKSCREEN PRINTED SURFACES
Clean using an appropriate product. Always dry thoroughly.
IMPORTANT: these parts must be cleaned very carefully to avoid scratching and abrasion. You are advised to use a soft cloth and neutral soap.
CAUTION: Do not use abrasive substances or non-neutral detergents as these
will irreparably damage the surface.
GLASS CONTROL PANEL
Clean using an appropriate product.
Always dry thoroughly.
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the control panel
since they can scratch the surface, which may result in shattering of the glass.
28
INSIDE OF OVEN
■
The oven should always be cleaned after use when it has cooled down.
The cavity should be cleaned using a mild detergent solution and warm water.
Suitable proprietary chemical cleaners may be used after first consulting with the
manufacturers recommendations and testing a small sample of the oven cavity.
Abrasive cleaning agents or scouring pads/cloths should not be used on the cavity surface.
■
NOTE: The manufacturers of this appliance will accept no responsibility for damage caused by chemical or abrasive cleaning.
Let the oven cool down and pay special attention no to touch the hot heating
elements inside the oven cavity.
Do not store flammable material in the oven.
■
■
ADVICE FOR USE AND MAINTENANCE OF CATALYTIC PANELS
The catalytic panels are covered with special microporous enamel which absorbs
and does away with oil and fat splashes during normal baking over 200 °C. If,
after cooking very fatty foods, the panels remain dirty, operate the oven “idling” on
max temperature for about 30 minutes. These panels do not require to be
cleaned, however it is advised to periodically remove them from the oven (at least
the side panels) and to wash them with tepid soapy water and then wipe off with
a soft cloth.
DO NOT CLEAN OR WASH THEM WITH ABRASIVE PRODUCTS OR WITH
PRODUCTS CONTAINING ACIDS OR ALKALIS.
The side panels are reversible and when the catalytic microporous enamel
degrades, they can be turned to the other side.
GRILL HEATING ELEMENT
■
The heating element is self-cleaning and does not require maintenance.
The grill is secured to the rear wall of the oven on a hinge system that allows
it to be lowered to allow proper access when cleaning the oven ceiling (fig.14
at page 13).
GREASE FILTER
■
■
Clean the filter after any cooking! The grease filter can be removed for cleaning
and should be washed regularly in hot soapy water (fig. 11 at page 12).
Always dry the filter properly before fitting it back into the oven.
29
REPLACING THE OVEN LAMPS
WARNING: Ensure the appliance is switched off before replacing the lamp
to avoid the possibility of electric shock.
■
Let the oven cavity and the heating elements to cool down;
■
Switch off the electrical supply;
■
Remove the protective cover A (fig. 26);
■
Unscrew and replace the bulb B with a new one suitable for high temperatures
(300 °C) having the following specifications: 230-240V 50 Hz, E14 and same
power (check watt power as stamped in the bulb itself) of the replaced
bulb.
■
Refit the protective cover A;
NOTE: Oven bulb replacement is not covered by your guarantee.
Figure 26
A
30
B
B
A
REMOVING AND REPLACING THE INNER DOOR GLASS
PANE FOR CLEANING
If you wish to clean inner glass of the door, make sure you follow the precautions
and instructions very carefully.
Replacing the glass pane and the door incorrectly may result in damage to the oven
and may void your warranty.
IMPORTANT!
• Take care, the oven door is heavy. If you have any doubts, do not attempt to
remove the door.
• Make sure the oven and all its parts have cooled down. Do not attempt to handle
the parts of a hot oven.
• Take extreme care when handling the glass pane. Avoid the edges of the glass
bumping against any surface. This may result in the glass shattering.
• Don’t use oven cleaners or any other harsh/abrasive cleaners, cloths, scouring pads,
steel wool or sharp metal scrapers to clean the glass surfaces. These scratch the
glass and may damage its special coating, which in turn could result in the glass
cracking or shattering.
• If you notice any sign of damage on any of the glass panes (such as chipping, or
cracks), do not use the oven. Call your Authorised Service Centre or Customer Care.
• Make sure you replace the glass pane correctly. Do not use the oven without glass
pane correctly in place.
• If the glass pane feel difficult to remove or replace, do not force it. Call your
Authorised Service Centre or Customer Care.
Note: service visits providing assistance with using or maintaining the oven are not
covered by your warranty.
31
REMOVING THE DOOR
Figure 27a
The oven door can easily be removed
as follows:
– Open the door to the full extent (fig.
27a).
– Open the lever A completely on the
left and right hinges (fig. 27b).
– Hold the door as shown in fig. 27.
– Gently close the door until left and
right hinge levers A are hooked to
part B of the door (fig. 27c).
Figure 27b
A
– Withdraw the hinge hooks from their
location following arrow C (fig. 27d).
– Rest the door on a soft surface.
B
Figure 27c
Figure 27
Figure 27d
CC
32
REMOVING THE INNER PANE OF GLASS
The oven door is fitted with no. 2 panes:
- no. 1 outside;
- no. 1 inner.
To clean all panes on both sides it is necessary to remove the inner pane as follows:
REMOVE THE INNER GLASS RETAINER
1. Remove the oven door and place it on a soft surface.
IMPORTANT: The door shall be placed horizontally as per figure 28.
2. Press down on both tabs to release the glass retainer.
3. Remove the glass retainer.
Figure 28
1
2
2
1
2
33
REMOVE THE INNER GLASS PANE
Lift and remove the inner pane slightly, as shown in the figure 29.
Figure 29
2
1
34
AFTER CLEANING, REPLACE THE INNER GLASS PANE
When replacing the inner glass pane, make sure that:
• You replace the pane correctly, as shown. The pane must be in the position described
below in order to fit into the door and to ensure that the oven operates safely and
correctly.
• You take extra care not to bump the edges of the glass against any object or surface.
• You do not force the pane into place. If you are experiencing difficulties replacing
the pane, remove it and start the process again from the beginning. If this still does
not help, call Customer Care.
• Check that you are holding the pane the correct way. You should be able to read
the wording on it as it faces you.
1. Insert the inner glass pane in the uppermost pair of grooves and push it slightly
(arrow 1 in figure 30).
2. Gently lower into place (arrow 2 in figure 30).
Figure 30
2
1
35
REPLACE THE GLASS RETAINER
1. Position the glass retainer, as shown in the figure 31. It should sit on the bottom
edge of the outer glass. Check that the clamps M are not deformed or damaged.
2. Gently push the glass retainer back into place. You should be able to hear the tabs
on both sides click as they lock the glass retainer in.
Important!
Make sure the glass retainer is correctly and firmly in place and that the
glass pane is secure.
Figure 31
2
click
M
1
M
1
M
2
click
36
REFIT THE DOOR
1. Hold the door firmly (fig. 32).
2. Insert the hinge tongues into the slots, making sure that the groove drops into
place as shown in the figure 33.
3. Open the door to its full extent.
4. Fully close the levers “A” on the left and right hinges, as shown in the figure 34.
5. Close the door and check that it is properly in place.
Figure 32
Figure 33
Figure 34
A
37
TROUBLESHOOTING:
If you experience a problem with your oven, check the following points before calling our Customer Service Centre for assistance.
1.
2.
3.
4.
The power is switched on.
The controls are switched on.
The electronic programmer is set to manual.
Both the fuse and the mains fuse are intact.
Should you still require assistance please contact our Customer Service Centre for
your nearest Authorised Delonghi Service Agent.
38
Descriptions and illustrations in this booklet are given as simply indicative. The manufacturer reserves the right,
considering the characteristics of the models described here, at any time and without notice, to make eventual
necessary modifications for their construction or for commercial needs.
39
Cod. 1103388-ß2