DeLonghi ESAM6600 Coffeemaker User Manual

De’Longhi America, Inc.
Park 80 West, Plaza One
Saddle Brook, NJ 07663
#1-866-Latte-Best
1-866-528-8323
De’Longhi Canada, Inc.
6150 McLaughlin Road
Mississauga, Ontario
L5R 4E1 Canada
#1-866-Latte-Best
1-866-528-8323
Fiducia Italiana S.A. de C.V.
Pestalozzi #814
Col. Narvarte
Del. Benito Juarez
C.P. 03100
tels: 5543 1447
lada sin costo: 01 800 711 8805
5732148500/12.06
www.delonghi.com
FULLY AUTOMATIC COFFEE CENTER ESAM6600
IMPORTANT INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MACHINE À CAFÈ AUTOMATIQUE ESAM6600
MODE D’EMPLOI IMPORTANT
CONSERVEZ LES PRESENTES INSTRUCTIONS
CAFETERA SUPERAUTOMATICA ESAM6600
INSTRUCIONES IMPORTANTES
REPASE Y GUARDE E
STAS INSTRUCCIONES LEA ESTE
INSTRUCTIVO ANTES DE UTILIZAR
EL APARATO
MACCHINA PER CAFFÈ
SUPERAUTOMATICA ESAM6600
ISTRUZIONI IMPORTANTI
CONSERVARE LE ISTRUZIONI
Register this product on-line and receive a
free trial issue of Cook's Illustrated. Visit
http://registration.delonghi-csservice.com.
Visit www.delonghi.com for a list of service
centers near you. (U.S. and Canada only)
Enregistrez ce produit en ligne et recevez un
numéro gratuit de Cook's Illustrated. Visitez
http://registration.delonghi-csservice.com.
Visitez www.delonghi.com pour y voir une liste
des centres de réparation proches de chez vous. (É.-U. et Canada seulement).
Registre este producto en línea y reciba un ejemplar gratis de Cook's Illustrated.
Visite http://registration.delonghi-csservice.com.
Visite www.delonghi.com para ver la lista de centros de servicios cercanos a usted. (Sólo Estados Unidos y
Canada)
Registra questo prodotto "on-line" per ricevere una copia omaggio della rivista.
Visita http://registration.delonghi-csservice.com.
Visita www.delonghi.com per una lista dei centri di servizio a te piu vicini. (Solo Stati Uniti e Canada)
ELECTRONIC CHARACTERISTICS: CARACTÉRISTIQUES ÉLECTRIQUES: CARACTERISTICAS ELECTRICAS:
CARATTERISTICHE ELETTRICHE: 120V˜60HZ 1100W
Collection
-
Collection
-
Colleción
-
Collezione
C o l l e c t i o n
-
C o l l e c t i o n
-
A B C D E
F
H
G
X
cappuccino
container pointer in
position 1
please wait ...
I
W
M
J
V
K
L
N
U
T
R
O
P
S
Q
1
2
3
cappuccino
container pointer in
position 1
please wait ...
4
13
5
6
9
12 11
-
C o l l e c i ó n
-
8
7
10
C o l l e z i o n e
C o l l e c t i o n
-
C o l l e c t i o n
-
1
2
1
2
-
C o l l e c i ó n
-
C o l l e z i o n e
Coffee has been used to factory test the appliance and it is therefore completely normal for there to be
traces of coffee in the mill. This appliance is, however , guaranteed to be new.
INDEX
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DESCRIPTION (see page 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USING FOR THE FIRST TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TURNING ON AND PREHEATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PREPARING COFFEE (USING COFFEE BEANS) AND USEFUL TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHANGING THE QUANTITY OF COFFEE IN THE CUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REGULATING THE COFFEE MILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PREPARING ESPRESSO COFFEE USING GROUND COFFEE (INSTEAD OF BEANS) . . . . . . . . . . . . . . . . . .
PRODUCING HOT WATER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHANGING THE QUANTITY OF HOT WATER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PREPARING CAPPUCCINO (FROTHED MILK AND COFFEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PREPARING LATTE OR ITALIAN MACCHIATO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PREPARING FROTHED OR STEAMED MILK (WITHOUT COFFEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHANGING THE QUANTITY OF COFFEE AND MILK FOR
LATTE/ CAPPUCCINO / ITALIAN MACCHIATO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.1 CLEANING THE COFFEE MAKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.2 CLEANING THE INFUSER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.3 CLEANING THE MILK CONTAINER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHANGING AND SETTING THE MENU PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.1 SETTING THE CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.2 SETTING AUTO-START TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.3 DESCALING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.4 CHANGING THE COFFEE TEMPERATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.5 CHANGING THE LENGTH OF TIME THE APPLIANCE REMAINS ON . . . . . . . . . . . . . . . . . . . . . . . . . .
17.6 SETTING WATER HARDNESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.7 RESETTING FACTORY DEFAULT SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.8 BEEP ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHANGING THE LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROBLEMS TO BE RESOLVED BEFORE CALLING THE SERVICE CENTER . . . . . . . . . . . . . . . . . . . . . . . . . .
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
C o l l e c t i o n
7
8
8
9
9
10
10
12
12
12
13
13
13
14
14
15
15
15
15
17
17
17
17
18
19
19
19
19
20
20
21
22
24
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed, including the
following.
• Read all instructions carefully.
• Make sure the voltage of your electrical system corresponds to the voltage shown on the
bottom of the machine.
• Do not touch hot surfaces. Use handles or knobs.
• To protect against fire, electrical shock and personal injury, do not immerse cord, plug or
appliance in water or other liquid.
• Keep the appliance out of the reach of children and do not leave appliance unattended
while in operation.
• Unplug from the outlet when not in use and before cleaning.
• Do not operate with a damaged cord or plug, or after the appliance malfunctions, or has
been damaged in any manner. Return the appliance to the nearest authorized service facility for examination, repair or adjustment.
• The use of accessory attachments not recommended by the manufacturer may result in fire,
electrical shock, or personal injury.
• Do not use outdoors.
• Make sure the power cord does not hang over the edge of the table or counter-top to avoid
getting accidentally caught or entangled.
• Do not place the appliance or its electrical parts on or near electric stoves, cooking surfaces,
or gas burners.
• Plug cord into the wall outlet.To disconnect, turn any control to “off”, then remove plug from
wall outlet.
• Do not use the appliance for other than the intended use.This appliance is to be utilized for
domestic use only. The manufacturer declines all responsibility for any damage caused by
improper, incorrect, or irresponsible use.
WARNING: To reduce the risk of fire or electric shock, do not remove the cover. No user
serviceable parts inside. Repair should be done by authorized service personnel only!
SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY
SHORT CORD INSTRUCTIONS
-
A short power cord is provided to reduce risks resulting from becoming entangled in or tripping over
a longer cord.
-
Longer, detachable power supply cords or extension cords are available and may be used if care is
exercised in their use.
-
If an extension cord is used, the marked electrical rating should be at least as great as the electrical
rating of the appliance. If the appliance is provided with 3- wire, grounding type cord, the extension
should be a GROUNDING TYPE 3 - WIRE CORD. The longer cord should be arranged so that it will
not drape over the counter-top or table top where it can be pulled on by children or tripped over.
-
Your product is equipped with a polarized alternating current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If
you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail
to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
C o l l e c t i o n
7
1 DESCRIPTION (SEE PAGE 3)
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.
V.
W.
X.
Grinding coarseness regulator
Coffee bean container
Bean container lid
Central lid for ground coffee
Compartment for measuring scoop
Cup warmer tray
Ground coffee funnel
Milk container lid with milk frother regulator
Milk spout
Milk intake tube
Nozzle
Water tank (removable)
Milk container
Power cable
Cup tray
Measuring scoop for pre-ground coffee
Drip tray (removable)
Hot water spout
Service door
Coffee grounds container (removable)
Coffee spout (adjustable in height)
Mobile drawer
Infuser
Control panel
Control panel
Some of the buttons on the panel have a dual function.This is
indicated in parentheses in the description.
1.
2.
3.
4.
5.
6.
7.
Appliance ON/OFF button
Display
One short coffee button
Two short coffees button
One long coffee button
Two long coffees button
Button for one Italian macchiato (or frothed
milk, if pressed twice consecutively)
8. Button for one cappuccino (or frothed milk if
pressed twice consecutively)
9. Button for one latte (or steamed milk, if pressed
twice consecutively)
10. Button to select coffee strength or preparation
with pre-ground coffee (OK button to confirm
changes to menu settings)
11. Hot water button (SET button to change menu
settings)
12. Rinse button (
button to change menu settings)
13. P button to enter the appliance menu (ESC button to exit menu)
2 SAFETY WARNINGS
READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE CONSULTATION!
• This appliance is designed to "make espresso coffee" and "hot drinks". Use with care to avoid scalds from
the water or steam jets or through incorrect use.
• This appliance is intended for domestic use only. Any other use is considered improper and thus dangerous.
• The manufacturer is not liable for damages caused by improper, incorrect or unreasonable use of the appliance.
• When using the appliance, do not touch the hot surfaces. Use handles or knobs.
• Do not touch the appliance with damp hands or feet.
• Do not allow children or infirmed persons to use the appliance unsupervised.
• Never allow children to play with the appliance.
• In the event of failure or malfunction, unplug the appliance from the outlet and do not tamper with it in
any way. If it requires repair, contact an authorized service center only and ask for original spare parts to
be used. Failure to respect the above could reduce the safety of the appliance.
• If the power cable is damaged, it must be replaced by the manufacturer or by the authorized service center to avoid all risks.
8
C o l l e c t i o n
3 INSTALLATION
•
After removing the packaging, make sure the product is complete and undamaged. If in doubt, do not use
the appliance and contact a qualified professional.
• Packing elements (plastic bags, polystyrene etc.) must not be left within reach of children as they may represent a hazard.
• Place the appliance on a work surface far away from water taps, basins and sources of heat.
• After positioning the appliance on the work top, leave a space of at least 2 in. (5 cm) between the surfaces of the appliance and the side and rear walls and at least 8 in. (20 cm) above the coffee maker.
• Never install the appliance in environments where the temperature may reach freezing or below
freezing temperatures (the appliance could be damaged if the water freezes).
• Make sure the mains voltage corresponds to the voltage indicated on the appliance rating plate. Connect
the appliance to a grounded socket with a minimum current rating of 10amps. The manufacturer is not
liable for possible accidents caused by failure to do so.
• If the power socket does not match the plug on the appliance, have the socket replaced with a suitable
type by a qualified professional.
• The power cable on this appliance must not be replaced by the user as this operation requires the use of
special tools. If the cable is damaged or requires replacing, contact an authorized service center only to
avoid all risks.
• You should personalize water hardness as soon as possible following the instructions in section 17.6.
• Coffee has been used to factory test the appliance and it is therefore completely normal for there to be
traces of coffee in the mill. This appliance is, however, guaranteed to be new.
To learn how to operate the appliance correctly, when you use it for the first time, follow the step-by-step
instructions given in the following sections.
4 USING FOR THE FIRST TIME
1. The first time you use the appliance, select the language.
To set English, plug the appliance into the outlet and wait for the appliance to display:
PRESS OK TO INSTALL ENGLISH
Press the OK button (fig. 1) for at least three seconds until you hear a BEEP and the display shows:
ENGLISH INSTALLED
The appliance then displays the setting message in English. If you select the wrong language by mistake,
follow the instructions in section 18 to choose the right one.
2. After 5 seconds, the appliance displays:
FILL TANK
To fill, remove the water tank (fig. 2), rinse and fill with fresh water. Never exceed the MAX line.
Put the water tank back and push as far as it will go.
3. Place a cup under the hot water spout (fig. 3). If the water spout is not in place, INSERT WATER SPOUT is displayed. Attach it as shown in figure 4; making sure the arrow on the spout is lined up with the arrow on
the control panel of the appliance, (fig. 4). The appliance now displays:
PRESS OK
4. Press the OK button (fig. 1). A little water will run from the spout (running water stops automatically).
5. The appliance now displays:
TURNING OFF
PLEASE WAIT...
and it goes off.
6. Fill the container with coffee beans (fig. 5), being careful not to exceed the MAX line.
IMPORTANT: To prevent malfunction, never fill with ground coffee, freeze dried coffee, caramelized beans
or anything else which could damage the appliance.
C o l l e c t i o n
9
5 TURNING ON AND PREHEATING
1. Press the
button (fig. 6). The appliance displays:
HEATING UP
PLEASE WAIT...
to indicate preheating is underway.
2. Once preheating is completed, the appliance displays
RINSING
PLEASE WAIT...
and performs an automatic rinse cycle (a little hot water runs from the spouts and is collected in the drip
tray below).
Tip: If you want a short coffee (less than 2 oz), to make it hotter, fill the cup with this hot rinsing water first.
Leave it for a few seconds then empty it to preheat the cup.
3. The appliance now displays the ready message:
READY Regular TASTE
6 PREPARING COFFEE (USING COFFEE BEANS) AND USEFUL TIPS
1. The appliance is preset to make coffee with a regular taste. You can also choose coffee with a mild, extramild, strong or extra-strong taste. To choose the required taste, press the
OK button (fig. 1). The
selected coffee taste will be displayed.
2. Place 1 cup under the spouts to make 1 short coffee (fig.7) or 2 cups for 2 short coffees (fig.8). For a creamier coffee, lower the spouts to bring them as close to the cups as possible (fig. 9).
3. Press one of the coffee buttons (fig. 10): the
button to make a short coffee or the
button for a long
coffee. To make 2 coffees, press the two short coffees button
or the two long coffees button
.
To change the quantity of coffee delivered automatically into the cup, follow the instructions in section 7.
(The appliance now grinds the beans and starts brewing the coffee into the cup. Once the desired quantity has been reached, the appliance automatically stops delivering the coffee and ejects the grounds into
the coffee grounds container.)
4. After a few seconds, the ready message is displayed again and you can make another coffee.
5. To turn the appliance off, press the
button.
(Before going off, the appliance performs an automatic rinse cycle: a little hot water runs out from the
spouts and is collected in the drip tray beneath. Take care to avoid scalds).
NOTE 1: If the coffee is delivered a drop at a time or not at all, turn the grinding coarseness regulator (fig.11) one
click toward the number 7 (see section 8).
Turn one click at a time until the coffee is delivered adequately.
NOTE 2: If the coffee is delivered too fast and is not creamy enough, , turn the grinding coarseness regulator (fig.
11) one click toward the number 1 (see section 8). Avoid turning the grinding coarseness regulator excessively; otherwise when you select 2 cups, the coffee may run out in drips. Mill should only be adjusted while running to prevent jamming.
NOTE 3: Tips to make hotter coffee:
• When you turn the appliance on, if you want to make a short coffee (less than 2 oz.), use the hot rinsethrough water to preheat the cups.
• If more than 2-3 minutes have passed since you last made coffee, before making coffee again you must preheat the infuser by pressing the button
(fig.12).
• Run off the water into the underlying drip tray or alternatively use this water to fill (and then empty) the
cup to be used for the coffee, so as to preheat it.
• Unless preheated, do not use cups that are too thick, as they will absorb too much heat.
• Use cups that have been preheated by rinsing them with hot water or by leaving them for at least 20 minutes on the cup warmer tray on top of the appliance with the appliance on.
NOTE 4: While the appliance is making the coffee, delivery can be stopped at any time by pressing the coffee button previously selected (fig.10).
10
C o l l e c t i o n
NOTE 5: As soon as delivery is complete, to increase the quantity of coffee, simply press and hold the coffee
button previously selected (fig. 10), until the desired quantity is reached (this operation must be performed
within 3 seconds from when coffee delivery from the spouts ceases).
NOTE 6: When the appliance displays:
FILL TANK
(and emits a double BEEP), the water tank must be refilled or the appliance will not make coffee.(It is normal for
there to be a little water left in the tank when the message is displayed.)
NOTE 7: The appliance counts the number of coffees made. Every 14 single coffees (or 7 doubles) the appliance displays:
EMPTY GROUNDS CONTAINER
(and emits a double BEEP), indicating that the grounds container is full and must be emptied and cleaned. Until
the grounds container has been cleaned, the appliance continues to display the message and cannot make
coffee.
To clean, open the service door at the front by pulling the handle (fig. 13), remove the drip tray (fig. 14), empty
and clean.
Empty the grounds container and clean thoroughly, making sure all residue deposited on the bottom is
removed.
IMPORTANT: When removing the drip tray, the grounds container MUST be emptied, even if it is not completely full.
If this is not done, when making your next coffee, the grounds in the container may exceed the maximum level and
block the appliance.
NOTE 8: While the appliance is delivering coffee, never remove the water tank. If it is removed, it will not be
possible to make the coffee and the appliance will display:
GROUND TOO FINE ADJUST MILL AND
INSERT WATER SPOUT AND PRESS OK
To turn the appliance on again, you must insert the hot water spout (fig. 4), press the OK button and run off
water from the spout for a few seconds.
When using the appliance for the first time, 4-5 cups of coffee need to be made before the appliance
starts to give satisfying results.
If the appliance malfunctions, do not contact the service center right away.
The problem can almost always be resolved by following the instructions indicated in sections 19 and 20.
If this is not the case, or for further explanations, contact customer service by calling the number listed in the
warranty or visit www.delonghi.com for a list of service centers near you. (U.S. and Canada only)
C o l l e c t i o n
11
7 CHANGING THE QUANTITY OF COFFEE IN THE CUP
The appliance is factory preset to automatically deliver the following quantities of coffee:
- one short coffee (when the
button is pressed);
- one long coffee (when the
button is pressed);
- two short coffees (when the
button is pressed);
- two long coffees (when the
button is pressed);
To change these quantities, proceed as follows:
- Press the button
(or
or
or
) corresponding to the quantity you want to change
for at least 8 seconds, then release until the message "PROGRAM QUANTITY" is displayed and coffee is
delivered.
- When the coffee in the cup reaches the required level, press the same button again to memorize the new
amount. The appliance emits a double beep to confirm.
The appliance is now re-programmed with the new settings and displays: READY.
8 REGULATING THE COFFEE MILL
The coffee grinder is preset in the factory to prepare coffee correctly and should not require regulating initially.
However, after making the first coffees, if you find that coffee delivery is either too fast or too slow (in drips),
the grinding coarseness regulator can be adjusted (fig. 11).
Turning it 1 click (1 line) toward the number 7 speeds up coffee delivery (without drips).
Turning it 1 click toward the number 1 slows down delivery, giving a creamier appearance to the coffee.
These adjustments will only be evident after at least 2 cups of coffee have been brewed.
The grinding coarseness regulator must only be turned when the coffee mill is running.
Turn one click toward the number 1 to obtain finer ground coffee,
slower delivery and a creamier appearance.
Turn one click toward the number 7 for coarser ground coffee and
faster delivery (not a drop at a time).
9 PREPARING ESPRESSO COFFEE WITH GROUND COFFEE (INSTEAD OF BEANS)
Coffee has been used to factory test the appliance and it is therefore completely normal for there to be
traces of coffee in the mill. This appliance is, however , guaranteed to be new.
• Select the ground coffee function by pressing the
/OK button (fig. 1) repeatedly until
READY - PRE-GROUND COFFEE
•
•
flashes on the display. This disables the coffee mill function.
Lift the central lid, place one level measure of ground coffee in the funnel (see fig. 15) and proceed as
described in section 6. NOTE: You can make just one coffee at a time by pressing the
or
button.
Once the coffee has been delivered, to go back to making coffee using beans, deactivate the ground coffee function by pressing the
/OK button, and the coffee mill is enabled for operation again.
NOTE 1: Never add the ground coffee when the appliance is off to avoid it being dispersed inside the appliance.
NOTE 2: Never add more than one level measured scoop; otherwise either the appliance will not make the coffee and the ground coffee will be lost inside the appliance,
dirtying it, or the coffee will run off in drips and the message “LESS COFFEE” will be displayed.
NOTE 3: When measuring the quantity of coffee to be added, use the measuring scoop supplied only.
12
C o l l e c t i o n
NOTE 4: Use ground coffee for espresso coffee makers only. Do not use coffee beans, freeze-dried coffee or
other materials that could damage the appliance.
NOTE 5: If you add more than one measure of ground coffee and the funnel blocks, use a knife to push the coffee down (fig. 16), then remove and clean the infuser and appliance as described in section 16.2 "Cleaning the
infuser".
10 PRODUCING HOT WATER
• Always make sure the appliance is ready.
• Make sure the water spout is attached to the nozzle (fig. 4).
• Position a container under the spout (fig. 3).
• Press the
button (fig. 17).
The appliance displays:
HOT WATER
and hot water is delivered from the water spout into the container below (you should not run off hot water
for more than two minutes at a time). To stop the flow, press the
button. Once the set quantity of hot
water has been reached, delivery stops automatically.
11 CHANGING THE QUANTITY OF HOT WATER
The appliance is factory preset to automatically deliver 8.5 oz. of hot water. To change this quantity, proceed
as follows:
• Make sure the water spout is attached (fig. 4).
• Position a container under the spout (fig. 3).
• Press the
button (fig. 17) for at least 8 seconds until you hear a BEEP, then release. The appliance displays:
HOT WATER PROGRAM QUANTITY
•
and hot water is delivered from the water spout.
When the hot water in the cup reaches the required level, press the
button to memorize the new
amount. The appliance emits a double beep. (You should not run off hot water for more than two minutes
at a time).
12 PREPARING CAPPUCCINOS (FROTHED MILK AND COFFEE)
•
•
•
•
•
•
•
•
Select the required coffee strength to make the cappuccino by pressing the OK/
button (fig. 1).
Remove the frothed milk lid from the milk container.
Fill the container with about 3.5 oz. of milk for each cappuccino to be prepared (fig. 18). Never exceed the
MAX level (corresponding to about 25 oz.) marked on the container.
It is best to use fat-free or low-fat milk at refrigerator temperature (about 41°F/5°C).
Make sure the milk intake tube is correctly inserted in the rubber washer on the bottom of the milk container lid (fig. 19), then reposition the lid in the milk container and turn it counter-clockwise as far as it will
go.
Move the pointer on the milk container to position 2 (fig. 20).
Remove the hot water spout (fig. 21) and attach the milk container to the nozzle. You will hear a BEEP (fig.
22).
Position the milk tube as shown in fig. 23 and then place a sufficiently large cup under the coffee and milk
spouts.
Press the CAPPUCCINO button (fig. 24). The button lights up and the appliance displays:
CAPPUCCINO: CONTAINER POINTER IN POSITION 2
Make sure the pointer on the container lid is positioned on the same number indicated on the display. After
a few seconds, the frothed milk is delivered from the milk spout into the cup below. Milk delivery stops
automatically, then the coffee is delivered.
C o l l e c t i o n
13
NOTE 1: While preparing the cappuccino, milk or coffee delivery can be interrupted by pressing the CAPPUCCINO button.
NOTE 2: If you run out of milk while delivering frothed milk, remove the container and refill it. Then put it back
in place and press the CAPPUCCINO button to request a cappuccino again.
NOTE 3: To ensure the milk frother is absolutely clean and hygienic, after making cappuccinos, clean the channels inside the milk container lid:
• Place a cup under the milk spout.
• Press the CLEAN button on the milk container lid and hold down for at least 8 seconds (fig. 25). The appliance displays:
CLEANING
After cleaning is complete, remove the milk container and place in the refrigerator. You should not leave
the milk outside the refrigerator for more than 15 minutes.
NOTE 4: To change the quantity of coffee or frothed milk delivered automatically into the cup, follow the
instructions in section 15.
13 PREPARING LATTE OR ITALIAN MACCHIATO
•
•
•
Prepare the appliance as described to make cappuccino.
Before attaching the milk container to the nozzle, move the pointer to position 1 (FIG. 26) if you want to
make a LATTE (LATTE button) or position 2 (fig. 20) if you want to make ITALIAN MACCHIATO (ITALIAN
MACCHIATO button).
Press the LATTE button (fig. 27). The button lights up and the appliance displays:
latte: MILK CONTAINER POINTER IN POSITION 1
or
•
Press the ITALIAN MACCHIATO button (fig. 28). The button lights up and the appliance displays:
ITALIAN MACCHIATO: CONTAINER POINTER IN POSITION 2
Make sure the pointer on the container lid is positioned on the same number indicated on the display.
After a few seconds, the steamed or frothed milk is delivered from the milk spout into the cup below. (Delivery
stops automatically.)
14 PREPARING FROTHED OR STEAMED MILK (WITHOUT COFFEE)
To prepare only frothed milk without coffee or only steamed milk without coffee, move the pointer on the lid
to the desired position (1-2), then press the CAPPUCCINO, LATTE or ITALIAN MACCHIATO buttons twice
(within 2 seconds).
14
C o l l e c t i o n
15 CHANGING THE QUANTITY OF COFFEE AND MILK FOR LATTE / CAPPUCCINO /
ITALIAN MACCHIATO
The appliance is factory preset to automatically deliver standard quantities of coffee or milk. To change these
quantities, proceed as follows:
• Fill the container with milk up to the maximum level indicated on the container.
• Press the button corresponding to the preparation you want to change (LATTE/ CAPPUCCINO / ITALIAN
MACCHIATO) for at least 8 seconds until the appliance emits a BEEP and displays:
MILK FOR PROGRAM QUANTITY
•
•
Then release the button. The appliance starts delivering milk.
Once the required quantity of milk has been delivered, press the button selected previously again. Milk
delivery stops and the quantity is memorized. (The appliance emits a BEEP.)
After a few seconds, the appliance delivers coffee into the cup and displays:
COFFEE FOR . PROGRAM QUANTITY
•
Once the required quantity of coffee has been delivered, press the button selected previously again. Coffee
delivery stops and the quantity is memorized. A double BEEP confirms that the new values have been
memorized.
The appliance is now re-programmed with the new settings and displays: READY.
16 CLEANING AND MAINTENANCE
Before performing any cleaning operations, leave the appliance to cool down and unplug from the outlet.
Never immerse the coffee maker in water. It is an electrical appliance.
Do not use solvents, abrasive cleaning products or alcohol to clean the appliance. A soft damp cloth will suffice.
No component may be washed in the dishwasher.
16.1 Cleaning the coffee maker
Clean the grounds container (as described in section 6, note 7) whenever it requires emptying.
The water tank should also be cleaned regularly.
The drip tray is fitted with a level indicator (red) showing the level of water it contains.
When the indicator starts to become visible (a few millimeters under the drip tray), the drip tray must be emptied and cleaned.
Check that the holes in the coffee spout are not blocked.
To unblock them, scrape the dry coffee residues away with a needle (fig. 29).
Clean the nozzle after every use with a sponge as shown in fig. 30.
16.2 Cleaning the infuser
The infuser must be cleaned regularly to avoid the build-up of coffee encrustations which could cause malfunction. Proceed as follows:
• Turn the appliance off by pressing the
button (fig. 6) (do not unplug) and wait for the display to go off.
• Open the service door (fig. 13).
• Remove the drip tray and the grounds container (fig. 14) and clean.
• Press the two red release buttons on the infuser and pull it out (fig. 31).
• IMPORTANT:THE INFUSER CAN ONLY BE REMOVED WHEN THE APPLIANCE IS OFF. ATTEMPTING TO REMOVE
THE INFUSER WITH THE APPLIANCE ON MAY CAUSE SERIOUS DAMAGE.
• Wash the infuser under running water, without using detergents. Never wash the infuser in the dishwasher.
• Clean the inside of the appliance thoroughly. To remove coffee encrustations from the inside of the appliance, scrape with a plastic or wooden fork then vacuum up the residues with a vacuum cleaner (fig. 32).
• Replace the infuser by sliding it onto the supports and pin at the bottom, then push the PUSH symbol fully
in until it clicks into place.
C o l l e c t i o n
15
Infuser
Push the PUSH symbol fully in until
it clicks into place.
After having heard the click, check
that the red buttons have snapped
out.
Support
Pin
Bottom pipe on the infuser. The pin must be inserted
into the bottom pipe on the infuser.
Check that the two red buttons have snapped out, otherwise the door cannot be closed.
The two red buttons have not
snapped out
The two red buttons have
snapped out CORRECTLY
CORRECT
•
•
INCORRECT
Replace the drip tray, complete with the grounds container.
Close the service door.
NOTE 1: If the infuser is not inserted correctly, until it clicks into place, and the two red buttons have not
snapped out, the service door cannot be closed.
NOTE 2: If it is hard to insert the infuser, before inserting it, squeeze it to the right
size by pressing it forcefully from the top and bottom simultaneously, as shown in
figure .
NOTE 3: If it is still hard to insert the infuser, leave it out of the appliance, close the service door, unplug from
the outlet then plug in again. Wait for all the lights to go off, after the diagnostics, then open the door and
replace the infuser.
16
C o l l e c t i o n
16.3 Cleaning the milk container
Proceed as follows:
• Remove the milk spout (1) and intake tube (2).
• Remove the froth regulator (3) by pulling it
outwards (see figure)
• Wash all the components thoroughly with hot
soapy water. Make sure there is no milk residue
inside the two holes in the lid of the milk container,indicated by the arrows in the figure,or in
the groove (4) of the froth regulator.
• Replace the froth regulator, intake tube and
milk spout back in the milk container lid.
4
3
1
2
17 CHANGING AND SETTING THE MENU PARAMETERS
After pressing the
button, when the appliance is ready, you can use the internal menu to modify the following parameters and functions:
• Clock
• Auto-start time
• Auto start ON/OFF
• Descaling process
• Coffee temperature
• Length of time the appliance remains on
• Water hardness
• Resetting factory default values
• Washing procedure
• BEEP ON/OFF
Note: the last line of the display is the guide to the function buttons.
17.1 Setting the clock
To set the clock, proceed as follows:
• Press the P button, then press the
button (corresponding to the
repeatedly until the menu arrow is on:
symbol flashing on the display)
CLOCK 00:00
•
Press the
button (corresponding to the SET symbol flashing on the display) to set the time on the clock.
(If you hold the button down, the time is changed rapidly.)
• Press the OK button to confirm the value.
• Press the P button (corresponding to the ESC symbol flashing on the display) to exit programming mode
or
to change other parameters.
Note: to display the time with the appliance off, press any button. The time will be displayed for five minutes.
17.2 Setting auto-start time
This function programs the time the appliance will come on automatically and be ready for use.
• Make sure the clock on the appliance is set as described above.
• Press the P button then press the
button (corresponding to the
symbol flashing on the display)
repeatedly until the menu arrow is on:
START TIME 00:00
•
•
•
Press the
button (corresponding to the SET symbol flashing on the display) to set the auto-start time.
(If you hold the button down, the time is changed rapidly.)
Press the OK button to confirm the value.
Press the SET button again and the appliance displays:
AUTO-START NO
Press the
button (corresponding to the SET symbol flashing on the display) to modify the function
(the appliance displays: AUTO-START YES)
C o l l e c t i o n
17
•
•
Press the OK button to activate auto-start.
Press the P button (corresponding to the ESC symbol flashing on the display) to exit programming mode
or
to change other parameters.
NOTE: When auto-start time is set, the symbol
appears alongside the time on the display.
17.3 Descaling
Over time, the continuous heating up of the water used to make the coffee leads to lime scale building up in
the inner circuits of the appliance.
When the message:
DESCALE
flashes on the display, you should perform the descale cycle.
Proceed as follows:
• Make sure the appliance is ready.
• Press the P button then press the
button (corresponding to the
then press the button repeatedly until the appliance displays:
symbol flashing on the display)
DESCALE NO
•
Press the
plays:
button (corresponding to the SET symbol flashing on the display) and the appliance dis-
DESCALE YES
•
•
•
•
•
Press the OK button to start the descale program.
Empty the water tank and pour in the contents of one bottle (4.2 fl. oz.) of DURGOL descaler plus 34 oz. of
water. NOTE: Make sure splashes of descaler do not fall onto surfaces sensitive to acid such as marble, limestone and granite.
For subsequent descaling operations, use the same type and brand of descaling solution as supplied (available from authorized technical service centers).
Attach the water spout to the nozzle.
Place a container with a minimum capacity of 34oz. under the hot water spout (Fig. 3).
Press the OK button. Descaler runs off from the hot water spout into the container below. The appliance
displays:
APPLIANCE IN DESCALE
•
•
The descale program automatically performs a series of run offs and pauses to remove lime scale deposits
from inside the coffee maker.
After about 30 minutes, the appliance displays:
RINSING FILL TANK
The appliance must now be rinsed through to eliminate residues of descaling solution from inside the appliance. Proceed as follows:
• Empty the water tank, rinse and fill with clean water.
• Reposition the tank.
• Empty the full container and then put it back under the hot water spout.
• Press the OK button. Hot water will run off from the spout into the container below and the appliance displays:
RINSING
•
When the water tank is empty, the appliance displays the message:
RINSING COMPLETE PRESS OK
•
•
Press the OK button and refill the water tank with clean water.
The descale program is now terminated and the appliance is ready to make coffee again.
18
C o l l e c t i o n
NOTE: If the descaling cycle is interrupted before completion, the appliance continues to display the descale
message and the program must be started again from the beginning. Empty the water tank, rinse, fill with clean
water and run off a cup of hot water.
IMPORTANT: FAILURE TO DESCALE THE APPLIANCE REGULARLY INVALIDATES THE WARRANTY.
17.4 Changing coffee temperature
To change the temperature of the coffee, proceed as follows:
• Press the P button, then press the
button (corresponding to the
repeatedly until the menu arrow is on:
symbol flashing on the display)
HIGH TEMPERATURE
•
•
•
Press the
button (corresponding to the SET symbol flashing on the display) until the appliance displays the required coffee temperature. Note: To obtain hotter coffee, see also section 6, note 3, page 10.
Press the OK button to confirm the temperature selected.
Press the P button (corresponding to the ESC symbol flashing on the display) to exit programming mode
or
to change other parameters.
17.5 Changing the length of time the appliance remains on
The appliance is factory preset to go off automatically one hour after the last coffee has been made.
The number of hours the appliance remains on (max. 3) can be increased as follows:
• Press the P button, then press the
button (corresponding to the
symbol flashing on the display)
repeatedly until the menu arrow is on:
OFF AFTER 1 HOUR..
•
•
•
Press the
button (corresponding to the SET symbol flashing on the display) to change the number of
hours the appliance remains on.
Press the OK button to confirm the value.
Press the P button (corresponding to the ESC symbol flashing on the display) to exit programming mode
or
to change other parameters.
17.6 Setting water hardness
The descale message is displayed after the appliance has been operated for a factory set period of time calculated on the basis of the maximum quantity of lime scale which may be contained in the water used.
If necessary, this period of operation can be extended, making descaling less frequent, by programming the
appliance based on the actual lime content in the water used.
Proceed as follows:
• Remove the "Total Hardness Test" strip (enclosed on page 2) from its packaging then dip it fully in the water
for a few seconds and remove. After about a minute 1, 2, 3 or 4 red squares develop.
• Press the P button, then press the
button (corresponding to the flashing
symbol on the display)
repeatedly until the menu arrow is on:
WATER HARDNESS 4
•
Press the
button (corresponding to the SET symbol flashing on the display) repeatedly until the number coincides with the number of red squares on the test strip (for example, if there are 3 red squares on
the test strip, press the button until WATER HARDNESS 3 is displayed).
• Press the OK button to confirm the value. The coffee maker is now programmed to provide the descaling
warning when necessary, based on the actual hardness of the water.
• Press the P button (corresponding to the ESC symbol flashing on the display) to exit programming mode
or
to change other parameters.
17.7 Resetting factory default settings
If you change the original values, the factory default values can be reset as follows:
• Press the P button, then press the
button (corresponding to the symbol flashing on the display)
repeatedly until the menu arrow is on:
RESET TO DEFAULT NO
•
Press the
button (corresponding to the SET symbol flashing on the display) and the appliance displays “RESET TO DEFAULT YES”.
C o l l e c t i o n
19
•
•
•
Press the OK button to reset the factory default values.
Press the P button (corresponding to the ESC symbol flashing on the display) to exit programming mode
or
to change other parameters.
The appliance is now reset to the factory default settings and the READY message is displayed.
17.8 Beep ON/OFF (activates and deactivates the beep)
• Press the P button, then press the
button (corresponding to the
repeatedly until the menu arrow is on:
symbol flashing on the display)
beep on
•
•
•
•
Press the
button (corresponding to the SET symbol flashing on the display) and the appliance will display "
".
Press the OK button to turn the beep off.
Press the P button (corresponding to the ESC symbol flashing on the display) to exit programming mode
or
to change other parameters.
The appliance is now set not to emit any beeps and displays the message READY
18 CHANGING THE LANGUAGE
To change the language, press the OK button for at least 5 seconds until the appliance displays the installation
message in various languages. Select the required language and press OK for 3 seconds (as described in section 4.1).
20
C o l l e c t i o n
19 TROUBLESHOOTING
MESSAGE
MEANING
WHAT TO DO
•
The water tank is empty or is positioned •
incorrectly.
Fill the water tank as described in section 4, and insert it fully.
•
The tank is dirty or encrusted with lime •
scale.
Rinse or descale the tank.
GROUND TOO FINE ADJUST MILL
AND
•
The coffee runs off too slowly.
•
Turn the grinding regulator (fig. 11) one
click toward the number 7 (see section
8).
INSERT WATER SPOUT AND
PRESS OK
•
The appliance cannot make coffee.
•
Insert the hot water spout, press the
button and run off water from the spout
for a few seconds.
•
The grounds container is full or missing. •
Empty the grounds container and clean
as described in section 6, note 7, then
replace.
•
After cleaning, the grounds container •
has not been replaced.
Open the service door and insert the
grounds container.
•
With the function selected, the pre- •
ground coffee has not been poured into
the funnel.
Add the ground coffee as described in
section 9.
•
•
•
The coffee beans have run out.
If the coffee grinder is very noisy, this •
means a small stone in the coffee beans
has blocked the mill.
Fill bean container.
Contact an authorized De' Longhi service center.
•
This indicates the presence of lime scale •
in the appliance.
The descaling procedure, described in
section 17.3, needs to be performed as
soon as possible.
•
After cleaning, the infuser has probably •
been left out of the coffee maker.
Leave the service door closed and the
infuser out of the appliance, press the
pointed buttons, then follow the
instructions displayed.
•
The service door is open
If the service door cannot be closed,
check that the infuser is inserted correctly (section 16.2 - note 1).
•
The
button has been pressed and
the hot water spout has not been inserted.
•
Insert the hot water spout (fig. 4).
•
After cleaning, the infuser has probably
been left out of the coffee maker.
•
Insert the infuser, see section 16.2.
•
•
The ground coffee funnel is clogged.
•
Too many coffee beans or too much
ground coffee has been added.
•
Empty the funnel with the help of a knife,
as described in section 9, note 5 (fig. 16).
Select a milder taste or reduce the quantity of ground coffee, then press
or
or
or
to deliver
the coffee again.
•
The inside of the appliance is very dirty.
•
Clean the inside of the appliance thoroughly, as described in section 16.2. If
the message is still displayed after cleaning, contact a service center.
FILL TANK
EMPTY GROUNDS CONTAINER
INSERT GROUNDS CONTAINER
ADD PRE-GROUND
COFFEE
FILL BEANS CONTAINER
DESCALE
PRESS
•
CLOSE DOOR
INSERT WATER SPOUT
INSERT INFUSER ASSEMBLY
LESS COFFEE
GENERIC ALARM
C o l l e c t i o n
21
20 PROBLEMS TO BE RESOLVED BEFORE CALLING THE SERVICE CENTER
If the appliance is not working, the causes of the malfunction can be identified and resolved by referring to section 19. If, on the other hand, a general alarm is on, run the following checks before calling the service center.
PROBLEM
The coffee is not hot
CAUSE
• The cups have not been preheated
• The infuser is too cold
The coffee is not creamy
enough
• The coffee is ground too coarsely
• Wrong type of coffee is being used
SOLUTION
• Heat the cups by rinsing them in hot water or leaving them
for at least 20 minutes on the cup warmer tray on the lid
(see section 6, note 3).
• Heat the infuser by pressing the
button before making
the coffee (fig. 12, see section 6, note 3).
• Turn the grinding adjustment knob one click toward the
number 1 (see section 8).
• Use a type of coffee for espresso coffee makers.
The coffee runs out too
slowly.
• The coffee is ground too finely.
• Turn the grinding regulator one click toward the number 7
(see section 8).
The coffee runs out too
quickly.
• The coffee is ground too coarsely.
• Turn the grinding regulator one click toward the number 1
(see section 8).
The coffee does not
come out of one of the
spouts.
• The spout holes are blocked.
• Scrape off the dry coffee residues with a needle (fig. 29).
When coffee beans are
being used and the
and • The ground coffee may be blocked in • Remove the ground coffee inside the funnel using a knife
the funnel.
(see section 9, note 5).Then clean the infuser and the inside
buttons are pressed,the
of the appliance (see description in section 16.2).
appliance does not deliver
coffee, but only water.
When the
button is
pressed, the appliance
does not turn on.
The infuser cannot be
removed for cleaning.
Ground coffee is being
used (not beans) and the
appliance does not deliver the coffee.
22
• The appliance is not plugged in.
• Check that the power cable is plugged into the outlet.
• The appliance is on. The infuser can • Turn the appliance off and remove the infuser (see section
only be removed if the appliance is off.
16.2). IMPORTANT: The infuser can only be removed if the
appliance is off. Attempting to remove the infuser with the
appliance on may cause damage.
• Too much ground coffee has been • Remove the infuser and thoroughly clean the inside of the
added.
appliance, as described in section 16.2. Repeat the operation
• The
button has not been
using a maximum of 1 measuring scoop of ground coffee.
pressed and the appliance has used • Thoroughly clean the inside of the appliance as described in
both the ground coffee added and the
section 16.2. Repeat the operation, first pressing the
coffee ground by the mill.
button as described in section 9.
• Ground coffee has been added when • Remove the infuser and thoroughly clean the inside of the
the appliance is off.
appliance, as described in section 16.2. Repeat the operation, but switch the appliance on first.
C o l l e c t i o n
The coffee does not
come out of the spouts,
but from around the
service door.
The milk does not run out
of the milk spout.
• The holes in the spouts are clogged • Scrape the holes with a needle (see section 16.1, fig. 29).
with dry coffee.
• The mobile drawer inside the service • Thoroughly clean the mobile drawer, particularly near the
door is blocked and cannot swing.
hinges to ensure they are free to swing smoothly.
• The intake tube is not inserted or is • Insert the intake tube in the rubber washer in the milk coninserted incorrectly.
tainer lid (fig. 19).
• The milk container lid is dirty.
• Clean the milk lid as described in section 16.3.
The milk is not well
frothed.
The milk contains bubbles or squirts out of the
milk spout.
• The milk is not cold enough or is not • We recommend using fat-free or low-fat milk at refrigerator
low-fat/fat-free.
temperature (about 41°F/5°C). If you are still not getting the
required results, try changing the brand of milk.
C o l l e c t i o n
23
This warranty applies to Super Automatic Espresso Machines with the De'Longhi brand name.
LIMITED WARRANTY
What does the warranty cover?
We warrant each appliance to be free from defects in material and workmanship. Our obligation under this
warranty is limited to repair at our factory or authorized service center of any defective parts or part thereof,
other than parts damaged in transit. The repaired or new model will be returned at the company expense.
This warranty shall apply only if the appliance is used in accordance with the factory directions, which accompany it, and on an alternating current ( AC ) circuit.
How long does the coverage last?
This warranty runs for two years ( 2 ) from the purchase date found on your receipt and applies only to the original purchaser for use.
What is not covered by the warranty?
The warranty does not cover defects or damage of the appliance, which result from repairs or alterations to the
appliance outside our factory or authorized service centers, nor shall it apply to any appliance, which has been
subject to abuse, misuse, negligence or accidents. Also, consequential and incidental damage resulting from
the use of this product or arising out of any breach of contract or breach of this warranty are not recoverable
under this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damage, so the above limitation may not apply to you.
How do you get service?
If repairs become necessary, see contact information below:
U.S. Residents:
Please contact our toll free hotline at #1-866-Latte-Best or log onto our website at www.delonghi.com.
For all accessories, spare parts or replacement parts, please contact our parts division at 1-866-528-8323.
Residents of Canada:
Please contact our toll free hotline at #1-866-Latte-Best or 1-866-528-8323 (Hours of Operation: Monday Friday 8:30am - 8pm, Saturday & Sunday 9:00am - 5:30pm) or log onto our website at www.delonghi.com.
Residents of Mexico:
Please refer to the Limited Warranty statement for Mexico (see page ).
Please refer to the back page of the manual for De’Longhi addresses.
The above warranty is in lieu of all other express warranties and representations. All implied warranties are limited to the applicable warranty period set forth above. This limitation does not apply if you enter into an
extended warranty with De’Longhi. Some states do not allow limitations on how long an implied warranty
lasts, so the above exclusions may not apply to you. De’Longhi does not authorize any other person or company to assume for it any liability in connection with the sale or use of its appliance.
How does state law apply?
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
24
C o l l e c t i o n
Download PDF

advertising