DeLonghi PAC600T Air Conditioner User Manual

PAC600T
• Use and maintenance manual . . . . pag.
4
• Mode d’emploi et d’entretien . . . . . pag.
16
• Instrucciones de uso . . . . . . . . . . pag.
28
• Manual de instruções . . . . . . . . . . pag.
40
I m p o r t a n t s a f e g u a rd s
• Use this appliance only as described in this instruction manual.
As with any electrical appliance, whilst the instructions aim to cover as
many eventualities as possible caution and common sense should be
applied when operating and installing this air conditioner.
• This appliance has been manufactured to cool and de-humidify
domestic environments and should not be used for other purposes.
• It is dangerous to alter or modify the unit's characteristics in any way.
• The appliance must be installed in line with the relevant national legislation.
• Should repairs be necessary, contact the nearest authorised Repair
Service Centre. Unauthorised servicing can be dangerous.
• This appliance is to be used by adults only; keep away from children.
• In the case that the power cable becomes damaged, this must be substituted only by specialised personnel authorised by the manufacturer.
• Always ensure the appliance is earthed. If you have any doubts check
with a qualified electrician.
• Avoid using extension leads with the unit.
• Before cleaning or maintenance operations, always unplug the unit
from the socket.
• Do not pull on or place strain on the power cable when moving the
appliance.
• The appliance should not be installed where the atmosphere may
contain combustible gases, oil or sulphur, or near heat sources.
• Do not rest hot or heavy objects onto the appliance.
• Remember to perform the descaling procedure at the end of each
season (see page 13). In areas where the water is particularly hard
(rich in minerals), the use of a commercial anti-lime product added to
the water is recommended. This can be requested from De’Longhi
LTD.
• Clean the filters at least once a week.
• Avoid using heaters near the unit.
• The unit should be transported in a vertical position. If this is not
possible secure the unit at an angle, do not lie horizontally.
• Before transporting the unit drain the condensation collecting-tray
and tank. After transportation, wait at least 1 hour before switching on
the unit.
• The packaging materials can be recycled. You are therefore recommended to place them in the special containers for differentiated
waste collection.
SAVE THESE INSTRUCTIONS
4
D
uring the summer, optimum comfort is achieved with a temperature of around 75°F (24 °C)
and 50% relative humidity.
An air conditioner removes moisture and heat from the room where it is located. One advantage
of portable air conditioning units over fitted models is that they can be moved from one room to
another in the home or even transferred between different buildings.
The hot air in your room is passed through
a coil cooled by refrigerant gas,
removing excess heat and moisture
before
being
discharged
again into the room.
In single unit models, a small
amount of this air is used to
cool the refrigerant gas,
then the hot and moist air is
discharged outside.
5
ENGLISH
How does your Pinguino work
Setting up
The following instructions will help you set up your air conditioning unit as efficiently as possible.
AIR CONDITIONING WITHOUT INSTALLATION
FOR INSTANT TEMPORARY USAGE
With just a few simple operations, Pinguino will
restore comfortable conditions in your room:
• With a double casement window, use the
suckers 27 provided to hold the two halves of the window together (fig. C).
• Fix the exhaust hose 25 to the coupling
8 on the back of the unit as shown in figure A.
1
C
2
A
• Fix the window attachment 26 to the end
of the hose 25 .
• Place the unit near a window or door.
• Open the window, or the door slightly and
place the window attachment 26 as
shown in figure B.
B
• Pinguino is equipped with an adjustable
window bracket. If you have a sash window, place the bracket on the window sill,
extend the bracket fully within the window
frame and lower the window onto the
bracket. Insert the nozzle of the exhaust
hose into the slot, then connect the hose
to the air conditioner (Fig. D).Thanks to the
wing nut, it’s possible to use the window
bracket also for sliding windows. Position the
hole of the bracket so to allow a correct
installation of the exhaust hose.
D
window
bracket
6
AIR CONDITIONING WITH INSTALLATION
For more efficient use Pinguino can also be
semi-permanently installed
• Fit the flange 24 supplied to the hole.
• Fix the hose 25 to the coupling on the
back of the unit (figure A).
• Attach the end of the hose 25 to the flange 24 as shown in the figure F.
F
MAX 47" (120 cm)
12"
30 cm
12"
30 cm
To install, proceed as follows:
• Make a hole in a outside wall or through
the glass of a window. Check the height
and dimensions given in figure E
MIN 12" (30 cm)
When the hose 25 is not attached, close the
hole with the bung on the flange 24 .
NOTE:
When the unit is installed semi-permanently,
we recommend leaving a door slightly open
(1 cm is enough) to ensure an adequate
exchange of air.
4"
100
E
in a window
pane
in the
wood sill of
a window
in the wall: for
optimum results,
insulate the section of the wall
with
suitable
insulating material.
7
ENGLISH
Setting up
Pre p a ra t i o n f o r u s e
HOW TO USE THE AIRCONDITIONER WITH WATER
These air conditioners can use both air and water to cool the condenser (the hot part) of the air
conditioner.
To utilise the full potential of your air conditioner, the tank 5 needs to be filled with water. The water
is used to increase the cooling power and reduce the noise level and energy consumption of the air
conditioner. The water that is used is then expelled from the machine as water vapour through the
exhaust hose 25 (it does not go into room).
Always use clean top water (which doesn’t contain salts). As a rule the water will usually last about 8
hours however this depends on the conditions within the room, such as temperature, humidity, insulation and aspect and number of people. In cool jet mode the water will also be used more quickly.
You may also use the airconditioner on air cooling only (without filling the water tank. if you only require the lower cooling power.
2
A) To open the front panel
3 grip either side of the
panel and gently pull the
panel towards you and
upwards. Remove the tank
5 Lifting it forward.
B) Turn the tank upside down
and remove the plug,
remove the extendible
tube and fill the tank, leaving it on the ground.
C) After completing the filling procedure, replace
the
extendible
hose,
replace the cap and
screw it in tightly. Return
the tank to its place, with
the writing FRONT clearly
visible. Carefully hold the
panel in the centre and
lower to its closed position.
During the "water functioning" operation and in particularly silent locations (eg the bedroom) a
slight gurgling sound may be heard. This is completely normal.
IN HIGH HUMIDITY CONDITIONS
Water is extracted from the air in the room, this water is also used to cool the appliance. When the
humidity is particulary high an excess of water may build up in the internal tank. This can be drained by removing the bung from the drain hose 9 and draining into a suitable receptacle.
IMPORTANT: if the room temperature is 90°F (32°C) or over the airconditioner must be operated
with water in the tank.
WARNING: Do not use water containing salt, eg. seawater or water treated using softening
systems that utilize kitchen salt.
8
ELECTRICAL CONNECTION
PROGRAMMED MODE
Before plugging in check that:
• the mains supply corresponds to the
power supply shown on the rating plate;
• the socket and the mains lead correspond
to the power requirements of the appliance;
• the socket is suited to the plug, otherwise
have the socket replaced;
• the socket is properly grounded.
1) Set the operating times by pushing out the
notches on the dial corresponding to the
period required (each notch represents 15
mins.)
The manufacturer cannot be held responsible for any damages due to failure in following normal safety procedures.
Replacement of the power cable must be
carried out by qualified personnel.
2) Press the TIMER key 12 , the signal light
14 will come ON.
3) Make sure that the timer indicates the correct time (see instructions on setting).
operating time
Funzionamento
11
10
9
4
SETTING THE TIMER
The programmer/timer 13 , like all clocks,
must be set to the exact time. If for example
it is 4.00 pm., turn the dial in a clockwise direction (following the direction of the arrow) until
the number 4 is lined up with the triangular
pointer (the arrows indicates 4:00 P.M.
approximately ).
11
10
4) Select the desired function as shown in the
chart overleaf.
N.B.: To override the programmed operating
times, simply press the ON/OFF key 16 (the
timer signal lamp 14 will go out)
9
4
pointer
N.B.: Never turn the dial in an anti-clockwise
direction!
The timer is in effect, an electric clock
and works only if the plug is connected to
the power supply. Whenever the plug is
disconnected or there is a power failure,
the programmer stops (the clock is then
“slow”) and must be re-set.
9
ENGLISH
Turning on and setting the timer
Selecting functions
AIR CONDITIONING FUNCTIONS
COOL JET
To turn the unit on in air conditioning mode,
proceed as follows:
The cool jet mode was conceived to provide
the appliance with a greater cooling potential. This is particularly useful when you want to
bring the temperature of a very warm room
quickly down to a more comfortable level. In
this case:
Make sure that the tank is full of water (see
page 8);
Make sure that the function selector switch
1. Press the ON/OFF button 11 (the signal
light
10 will come on).
2. Rotate the function selector 19 dial anticlockwise:
• Place the function selector in the HIGH
pos. to operate the unit in air conditioning
mode at maximum fan speed, after 3
minutes the signal light 15 will come on ).
• Place the function selector in the LOW
pos. to operate the unit in air condtioning
mode at minimum fan speed (the signal
light 21 will come on, and then, after 3
minutes the signal light 16 will come on ).
3. Now set the required temperature by rotating the room thermostat dial 20 .
Note
The temperature is not expressed in degrees.
We recommend that you turn the thermostat
dial to the maximum position. When the desired room temperature has been reached,
slowly turn the thermostat in a clockwise
direction until it arrives at the position where a
click can be heard. The signal lights 15 (or
16 ) will turn off.
The temperature selected in this way will
automatically be regulated and maintained,
and save energy. When regulating the thermostat, the air conditioning function is temporarily interrupted and the unit continues to
operate in fan only mode. In this way, the
appliance keeps the air temperature within
the room even.
Delay on Start Up
1. A special safety device will delay the start
of air conditionig by approximately 3 to 5
minutes when switching between functions or on initial start up.
2. You may also experience a slight delay
between changing from one function to
another.
10
19 is in the HIGH position.
Press the Cool jet button 22 .
After reaching the desired temperature, you
can release the Cool jet button and reposition the selector switch to the LOW pos.
Doing so will make the operation quiter.
VENTILATION/FILTRATION
Rotate the function selector 19 clockwise.
• Press the ON/OFF button 11 (the signal
light 10 will come on).
• Place the function selector on the “FreshZone” position and choose the desired fan
speed (min/max). The signal light 17 or
18 will come on).
PROBLEM WARNING LIGHT
23 indicates that
The lighted pilot light
the safety device of the pressure switch has
switched on. In this case the appliance is
deactivated. To restore the proper functioning of the appliance, eliminate the possible
causes of the problem and press the restore
button 6 .
The causes may be:
1) The exhaust hose forms a siphon in which
condensation water has accumulated: in
this case, it is necessary to drain the accumulated out of the machine, outwards
(never towards the air conditioner) and
eliminate the siphon on the hose.
2) The exhaust hose is obstructed: eliminate
the obstacles which obstruct the expulsion
of the air to the outside.
If, after having repositioned the drainage tube,
the machine still does not start up, the problem
might be more complicated (ex.: obstructed
ventilation fan) and could require the assistance of the Authorised Service Centre.
PURIFICATION FILTER
In addition to dust, this purification filter is able
to capture even the smallest sized particles
and impurities (up to 0.003 millimetres), such
as cigarette smoke.
The purification filter should never be used
with the dust filter, which is also included with
the appliance. Therefore:
A. If you wish to use the purification filter:
Remove the purification filter from the filter
housing;
Remove the aspiration grill 7 (fig. H on page
12) and the dust filter which is attached to this.
Remove the purification filter from its packaging.
Anchor the filter to the appliance by attaching the two plastic pieces on the filter to
the special supports on the air conditioner
(see the illustration below).
Set the dust filter aside.
exception is in the case of installation through a hole in the wall or window. In this case,
you are recommended to allow a small
amount of air to enter through a door or
window to guarantee an adequate
exchange of air.
• Protect the room from direct exposure to
the sun’s rays by drawing the curtains
and/or partially lowering the blinds so as
to maximise energy savings.
• Do not rest objects on the air conditioning
unit.
• Do not obstruct the air intake 7 or outlet
1 .
• Make sure there are no heat sources in the
room.
• Do not use outdoors.
B. If the dust filter is sufficient:
Remove the purification filter from the filter
housing and set it aside.
do not cover
RECOMMENDATIONS
Follow these recommendations to achieve
maximum efficiency from your air conditioning unit:
• Close the doors and windows in the room
where the unit is functioning. The only
lower the blinds or draw the curtains
close doors and windows
• Make sure the unit is located on a level
floor. If necessary, place the two blocking
devices 28 under the front wheels .
11
ENGLISH
Recommendations
Maintenance
Before cleaning or maintaining the unit, always
turn the unit off by releasing the ON/OFF button
11 and unplug from the mains .
CLEANING THE APPLIANCE
We recommend cleaning the appliance with
a slightly damp cloth then drying with a dry
cloth. For safety reasons, do not wash the air
conditioner with water.
Precautions
Never clean with benzene, alcohol or solvents. Never spray liquid insecticide or similar.
CLEANING THE FILTERS
Dust filter
Purification filter
Clean the external side of the purification filter once a week. Use a vacuum cleaner at
an intermediate power level. Never clean
the inside of the filter. Replace the purification
filter at the end of each season or in any
case, when it is no longer effective. The purification filter can be purchased in the store as
an accessory or at an Authorised Service
Centre as a replacement part. Alternatively,
the dust filter included with the appliance
may be used in place of the purification filter.
CLEANING THE RESERVOIR
All of the models are equipped with a dust filter able to capture the dust particles suspended in the air.
In order to maintain the effectiveness of your
air conditioner unaltered over time, remember to clean the dust filter every week.
1. Remove the aspiration grill 7 , (see fig. G);
2. Remove the filter holder housing by detaching it from the external grill. To detach it,
press on the two wings found on the side of
the filter holder (see fig. H)
Use a vacuum cleaner to remove the dust
deposits on the filter. If the filter is very dirty,
4
It is recommended that you clean this at least
once a month using the following method:
• turn off the appliance and remove the
plug from the electrical outlet.
• open the front panel 3 and remove the
tank 5 .
• remove the bung from the drainage hose
9 which can be found at the back the
air conditioner and empty out the water
to a container.
• after draining off the water, replace the
drainage hose plug.
• remove the dirt by scrubbing gently with a
cloth where the tank is positioned.
START OF SEASON CHECKS
Check that the power cord and socket are
undamaged and that the ground installation is
efficient. Carefully observe the installation
2
1
instructions.
fig. G
immerse it in warm water, rinsing it thoroughly.
The temperature of the water should be kept
under 40°C.
After washing it, let the filter dry before reinserting it into the holder.
fig. H
12
RECOMMENDED
OPERATIONS
TO
PERFORM AT THE END OF THE SEASON
1) Proceed with scaling procedures (see
page 13).
2) Remove the water from the collection
reservoir 4 .
3) Operate the appliance in the ventilation
only mode for about half an hour in order
to thoroughly dry the inside of the air conditioner.
4) Turn off the appliance and remove the
plug from the outlet.
5) Remove the drainage hose 21 .
6) Clean the filter and dry it thoroughly before replacing it in the appliance.
7) Cover the appliance so that dust does
not build up.
ENGLISH
De s c a l i n g
When the scale deposits become excessive
(on average, after about 400 hours of operation) or in any case, at least once each season, it is very important to proceed with the
decalcification of the appliance as described
below.
To remove the scale from the appliance, you
need:
• 20% of descaling liquid
29
• 80% of clean water
(corresponding to a diluted solution of 75%)
fig. I
Proceed as follows:
1) Remove the tank 5 from the appliance
and drain the water remaining in the collection reservoir 4
ge hose 9 (fig. I).
by using the draina-
2) Close the drainage hose 9 . Pour 500 ml
of decalcifying liquid and
2 litreS of clean water into the collection
fig. L
reservoir 4 which is found under the tank
(fig. L), on the bottom of the appliance.
3) Operate the air conditioner for about half
an hour.
4) After this, drain out all of the liquid remaining in the collection reservoir and rinse
thoroughly (fig. I). During the rinsing process, the drainage hose must be open
and the appliance functioning.
5) Unplug the appliance from the mains and
clean the collection reservoir thoroughly
with a clean cloth.
6) After cleaning the collection reservoir, the
air conditioner can be used normally.
IF TRACES OF SUDS CAN BE SEEN IN THE WATER WHEN THE MACHINE IS USED AGAIN AFTER IT HAS
BEEN CLEANED AS DESCRIBED ABOVE, THIS IS NORMAL HOWEVER, IF THERE ARE A LOT OF SUDS
RINSE THE APPLIANCE AGAIN THOROUGHLY TO REMOVE ALL TRACES OF CLEANING PRODUCT.
REQUEST ADDITIONAL QUANTITIES OF DECALCIFYING LIQUID FROM DE' LONGHI LTD.
ATTENTION:
The use of products other than De' Longhi could cause damage to the internal components of the
appliance and invalidate the terms of the warranty.
13
Troubleshooting
If the unit is not working properly, this may be due to small problems that you can easily resolve yourself.
Follow these instructions carefully before contacting your local Authorised Technical Service Centre.
PROBLEM
CAUSE
The air conditioner is •
completely turned •
off
the air conditioner is
on (signal light 10 )
•
but the appliance
doesn't start
The unit works but
does not cool the
room
•
•
plug in
wait
The teeth of the timer are in the rest mode
•
proceed with a new setting of
the timer
three minutes have not passed since it was •
turned on
•
•
windows open
a heat source is operating in the room (burner,
light, etc.) or there are a lot of people
the air outlet hose has come detached from
the coupling
thermostat adjusted too high
air filters clogged
the output of the unit is insufficient for the conditions or size of the room
•
•
•
14
it is not plugged in
there is no electricity
•
•
The unit works for
only a short time
REMEDY
•
•
wait three minutes (safety device) before the appliance start
cooling.
close the windows
eliminate heat sources
•
fit the hose in the coupling
•
•
lower the thermostat
clean/replace filters
•
•
there is a kink in the exaust hose
the exaust hose is blocked
•
•
•
•
there are too many curves in the outlet tube
the fan is blocked
•
•
position the exaust hose correctly
check there are no blockages
preventing the discharge of air
to the outside
rearrange the hose correctly
contact the Service Centre
TECHNICAL SPECIFICATION
Power supply
see rating plate
Max. absorbed power
in air conditioning
“
Refrigerating capacity
“
Refrigerant
“
Number of fan speeds
2
370 m3/h
Max. air flow .
RECOMMENDED OPERATING CONDITIONS
Room temperature 70°F -90°F (21 ÷ 32°C)
Dimensions:
• width
• height
• depth
580 mm
785 mm
435 mm
22 21/64”
30 13/32”
17 1/8”
This appliance contains substances which, if released into the atmosphere, would damage the
ozone layer. Care should therefore be taken not to perforate the refrigerant circuit. At the end of
its working life, delivery the air conditioning unit to a special collection centre.
FOR UNITED STATES ONLY:
LIMITED WARRANTY
We warrant each DE’LONGHI AIR-CONDITIONER to be free from defects in material and
workmanship. Our obligation under this warranty is to provide one year parts and labor free
from purchase date, with an additional four (4) years on any part of the sealed system consisting of the compressor, evaporator, condenser and factory connected refrigerant tubing.
This warranty shall apply only if the AIR-CONDITIONER is used in accordance with the factory directions which accompany it, and on Alternatign Current (AC) circuit. This warranty
is in lieu of all other warranties and representations, expressed or implied, and all other obligations or liabilities on our part. We do not authorize any other person or company to assume for us any liability in connection with the sale or use of our AIR-CONDITIONER. This warranty shall not apply to assume for us any liability in connection with the sale or use of our
AIR-CONDITIONER. This warranty shall not apply to any AIR-CONDITIONER which shall
have been repaired or altered outside our factory nor shall it apply to any AIR-CONDITIONER which has been subjected to misuse, negligence or accidents.
If repairs become necessary or spare parts are needed, plese write to:
De’Longhi America Inc.
Park 80 West Plaza One, 4th floor
Saddle Brook NJ 07663
or call Service Tel. No 1-800-322-3848
15
ENGLISH
Technical specification
D
ear Customer,
Thank you for having purchased an appliance made by De’ Longhi, the
international leader in portable air conditioning units. Thanks to our years
of experience all around the world we are constantly improving the quality and performance of Pinguino. We are confident that you will be satisfied with your purchase and enjoy the cool comfort created by the Pinguino for many years to come. You should spend some time reading this
instruction manual and keep it handy to refer to in order to use your Pinguino efficiently.
C
hère Cliente, Cher Client,
Nous vous remercions d’avoir choisi un produit De’Longhi, le plus important
fabricant mondial de climatiseurs portables. Des années d’expérience
dans le monde entier nous permettent d’améliorer constamment la qualité
et les performances de Pinguino. Nous sommes certains que vous serez
immédiatement satisfait de votre achat et que vous profiterez pendant
longtemps de la fraîcheur et du bien-être que Pinguino cré. Nous vous
prions de bien vouloir consacrer un peu de temps à la lecture de ce mode
d’emploi et de le conserver soigneusement. Ses conseils vous permettront
d’obtenir les meilleurs résultats de votre Pinguino en toute sécurité.
E
stimado Cliente
Le agradecemos por haber elegido un producto De’ Longhi, líder mundial en la fabricación de los acondicionadores portátiles. Años de experiencia en todo el mundo nos permiten mejorar constantemente la calidad y las prestaciones de Pingüino. Estamos seguros que quedará inmediatamente satisfecho de su compra y que gozará por largo tiempo el
fresco bienestar que da Pingüino. Le pedimos que dedique un poco de
su tiempo a la lectura de este manual de instrucciones y de guardarlo
con cuidado. De este modo, podrá usar Pingüino en condiciones de
máxima eficacia y serenidad.
Prezado Cliente
agradecemos por ter escolhido um produto Dé Longhi, o líder mundial na
fabricação dos condicionadores portáteis. Anos de experiência em todo
o mundo permitem-nos melhorar constantemente a qualidade e os
desempenhos dos aparelhos Pinguino. Temos certeza de que ficará logo
satisfeito com a sua compra e que usufruirá por muito tempo do fresco
bem-estar que Pinguino e Super Pinguino oferecem. Por favor, dedique
um pouco do seu tempo à leitura deste manual de instruções e conserve-o com cuidado. Desta forma, poderá utilizar o aparelho Pinguino com
a máxima eficácia e serenidade.
2
• De s c r i p t i o n • De s c r i p t i o n
• De s c r i p t c i ó n • De s c r i ç ã o
1
7
6
2
5
8
3
4
9
• CONTROL PANEL
• PANNEAU DE COMMANDE
• TABLERO DE MANDOS • PAINEL DE COMANDOS
13
15 16 17 18
23
10
11
12
14
19
20
• ACCESSORY-SET
• ACCESSOIRES
• ACCESORIOS
• ACESSÓRIOS
24
21 22
25
27
28
26
29
5751006700/01.02