DeLorme 6 GPS Receiver User Manual

3LCD DATA PROJECTOR
TLP-T70M
TLP-T71M
TLP-T60M
TLP-T61M
TLP-S40
TLP-S41
Before Using
OWNER’S MANUAL
(XGA)
(XGA / With Document Camera)
(SVGA)
TLP-T70M / T60M / TLP-S40
Others
Maintenance
(SVGA / With Document Camera)
Operations
(XGA / With Document Camera)
Preparations
(XGA)
Before Using
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES
ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND
INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE
MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE
REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can
result in electric shock or fire hazard. The safeguards incorporated in this unit will protect you
if you observe the following procedures for installation, use and servicing. This unit is fully
transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO
DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL ONLY.
1. Read Owner's Manual
3. Source of Light
After unpacking this product, read
the owner's manual carefully, and
follow all the operating and other
instructions.
Do not look into the lens while the
lamp is on. The strong light from
the lamp may cause damage to
your eyes or sight.
WARNING: Handling the cord on this product or cords associated with accessories sold with
USA only this product, will expose you to lead, a chemical known to the State of California
to cause birth defects or other reproductive harm. Wash hands after handling.
FCC Radio Frequency Interference Statement
Note:
This equipment has been tested and found to comply with the limits for a Class
USA only A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiates radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
WARNING: Changes or modifications made to this equipment, not expressly approved by
USA only Toshiba, or parties authorized by Toshiba, could void the user’s authority to operate
the equipment.
4. Ventilation
2. Power Sources
Openings in the cabinet are
provided for ventilation and to
ensure reliable operation of the
product and to protect it from
overheating, and these openings
must not be blocked or covered.
The openings should never be
blocked by placing the product on
a bed, sofa, rug or other similar
surface. This product should not
be placed in a built-in installation
such as a bookcase or rack unless
proper ventilation is provided or
the manufacturer's instructions
have been adhered to.
This product should be operated
only from the type of power source
indicated on the marking label.
If you are not sure of the type of
power supply to your home,
consult your product dealer or
local power company.
For products intended to operate
from battery power, or other
sources, refer to the operating
instructions.
Notice:
This Class A digital apparatus complies with Canadian ICES-003. Cet appareil
CANADA only numérique de la classe A est conforme à la norme NMB-003 du Canada.
WARNING: This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
CAUTION: Laser beam is emitted when the laser button of the remote control is pressed.
Do not look at the laser beam directly from the front of the remote control. Do not
turn the laser beam toward a person or to a mirror.
2
3
Before Using
SAFETY PRECAUTIONS
5. Heat
8. Power-Cord Protection
The product should be situated
away from heat sources such as
radiators, heat registers, stoves, or
other products (including
amplifiers) that produce heat.
Power-supply cords should be
routed so that they are not likely to
be walked on or pinched by items
placed upon or against them,
paying particular attention to cords
at plugs, convenience receptacles,
and the point where they exit from
the product.
11. Object and Liquid Entry
14. Attachments
Never push objects of any kind
into this product through openings
as they may touch dangerous
voltage points or short-out parts
that could result in a fire or electric
shock. Never spill liquid of any
kind on the product.
Do not use attachments not
recommended by the product
manufacturer as they may cause
hazards.
15. Accessories
Do not place this product on an
unstable cart, stand, tripod,
bracket, or table. The product may
fall, causing serious injury to a
child or adult, and serious damage
to the product. Use only with a
cart, stand, tripod, bracket, or table
recommended by the
manufacturer, or sold with the
product. Any mounting of the
product should follow the
manufacturer's instructions, and
should use a mounting accessory
recommended by the
manufacturer. A product and cart
combination should be moved with
care. Quick stops, excessive
force, and uneven surfaces may
cause the product and cart
combination to overturn.
6. Water and Moisture
Do not use this product near water.
- for example, near a bath tub,
wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a
swimming pool and the like.
9. Overloading
Do not overload wall outlets;
extension cords, or integral
convenience receptacles as this
can result in a risk of fire or
electric shock.
12. Do not place the product
vertically
Do not use the product in the
upright position to project the
pictures at the ceiling, or any other
vertical positions. It may fall down
and dangerous.
7. Cleaning
Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
Use a soft cloth for cleaning.
10. Lightning storms
For added protection for this
product during storm, or when it is
left unattended and unused for
long periods of time, unplug it from
the wall outlet. This will prevent
damage to the product due to
lightning and power-line surges.
4
13. Stack Inhibited
Do not stack other equipment on
this product or do not place this
product on the other equipment.
Top and bottom plates of this
product develops heat and may
give some undesirable damage to
other unit.
S3125A
5
Before Using
IMPORTANT SAFETY INSTRUCTIONS (Continued)
IMPORTANT SAFETY INSTRUCTIONS (Continued)
18. Servicing
Unplug this product from the wall
outlet and refer servicing to
qualified service personnel under
the following conditions:
a) When the power-supply cord or
plug is damaged.
b) If liquid has been spilled, or
objects have fallen into the
product.
c) If the product has been exposed to
rain or water.
d) If the product does not operate
normally by following the operating
instructions. Adjust only those
controls that are covered by the
operating instructions as an
improper adjustment of other
controls may result in damage and
will often require extensive work by
a qualified technician to restore
the product to its normal
operation.
e) If the product has been dropped or
damaged in any way.
f) When the product exhibits a
distinct change in performance this indicates a need for service.
Do not attempt to service this
product yourself as opening or
removing covers may expose you
to dangerous voltage or other
hazards. Refer all servicing to
qualified service personnel.
21. Do not leave thermalpaper documents or easily
deformed items on top of
the unit or near the air
exhaust for long periods
of time.
Before Using
16. Damage Requiring Service
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
19. Replacement Parts
When replacement parts are
required, be sure the service
technician has used replacement
parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
(Replacement of the lamp only
should be made by users.)
20. Safety Check
17. If glass components,
including lens and lamp,
should break, contact your
dealer for repair service.
Upon completion of any service or
repairs to this product, ask the
service technician to perform
safety checks to determine that
the product is in proper operating
condition.
This product incorporates glass
components, including a lens and
a lamp. If such parts should
break, please handle with care to
avoid injury and contact your
dealer for repair service. The
broken pieces of glass may cause
to injury. In the unlikely event of
the lamp rupturing, thoroughly
clean the area around the
projector and discard any edible
items placed in that area.
22. Do not get your hands
between the camera arm
and the main unit when
setting the camera arm
back in its original
position. (Models equipped
with document camera)
To avoid injury, be careful not to
get your hands caught when
setting the camera arm back in its
original position.
Families with children should be
particularly careful.
23. Do not carry by the camera
arm. (Models equipped with
document camera)
Do not carry the projector by the
camera arm. Doing so can result
in damage or injury.
24. Do not move the projector
while the arm is still erect.
(Models equipped with
document camera)
Always store the arm back in
position when moving the
projector. Otherwise injury or
damage may result.
6
7
POWER SUPPLY CORD SELECTION
If your line voltage is 220 to 240V, use one of the following types of cable.
MODEL NO. /
RATING Label
Plug
configuration Plug type
WARNING Label
SERIAL NO. Label
MANUFACTURED;
Plug
configuration
Line voltage
EURO
220 – 240V
UK
220 – 240V
SERIAL NO.
CAUTION Label
Use a 5A fuse which is approved by ASTA
or BSI to BSI362.
Always replace the fuse cover after
changing the fuse.
WARNING Label
Plug type
Line voltage
Australian
240V
10A
200 – 240V
Switzerland
240V
6A
200 – 240V
North American 200 – 240V
240V
15A
CAUTION Label
IMPORTANT PRECAUTIONS
CAUTION Label
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to
ship your LCD projector. For maximum protection, repack the set as it was originally
packed at the factory.
CAUTION Label (LASER)
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on
the crucial internal parts. To prevent the unit from possible damage, do not use the unit for
at least 2 hours when there is an extreme or sudden change in temperature.
Remote Control
IN
P
U
T
Y
PLA
LASER WARNING
Models with Document Camera
Place and Manner of Installation
• Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the LCD panel.
• Avoid locations with oil or cigarette smoke. Doing so will dirty the LCD panel and other
optical parts, shortening their lives, and darkening the screen.
• Do not place slantwise in angle of 20° or more. Doing so could shorten the life of the
lamp.
• Using this instrument near a TV or radio may cause intereference to the images or audio
sound. If this happens, move it away from the TV or radio.
• Moving the projector from a low-temperature room to a high-temperature room may
cause condensation on the lens or internal parts in the instrument. If you continue to use
it in that situation, the malfunction may result. Ensure to wait until the condensation
naturally disappears.
• In a high altitude location where air is thin, cooling efficiency of the scanner is reduced so
use it with the ambient temperature being lowered.
CAUTION Label (LASER)
8
9
Before Using
LABEL LOCATIONS
EXEMPTION CLAUSES
Avoid Volatile Liquid
• Toshiba Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation,
operating by third parties, other accidents, or use under abnormal conditions including
erroneous or improper operation and other problems.
• Toshiba Corporation bears no responsibility for incidental damages (lost profit, work
interruption, corruption or loss of the memory contents, etc.) arising from the use of or the
inability to use this unit.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from not
having followed the descriptions in this Instruction Manual.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from
malfunctions arising from combination with equipment or software that is not related to
Toshiba Corporation.
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time. They will leave marks on the finish.
If cleaning with a chemically saturated cloth, be sure to follow the product's precautions.
LCD Panel
The life of the LCD panel is limited. Take care over the points below so as to use the
panel for years.
• To prolong the life of this panel, never fail to turn the power off when the panel is not in
use and make sure that the lamp has gone out. The state of the lamp being extinguished
helps enhance the effect of energy saving.
• If the air filter is stained and is clogged up, the main unit inner temperature rises. As a
result, the life of the LCD is shortened and a malfunction may also occur.
Clean the air filter from time to time and replace it regularly. It is recommended that this
replacement be done at the time of replacing a lamp. (Ask a dealer where the unit was
purchased or your nearby service station about an air filter for replacement.)
In the spaces provided below, record the Model and Serial No. located at the bottom of
your LCD projector.
Model No.
OTHER CAUTIONS AND INFORMATIONS
Copyrights
Showing or transmitting commercial imaging software or broadcast or cable-broad
casting programs with the purpose of other than the personal and private viewing,
including modifying images using the freeze or resize functions, or displaying with the
varying aspect ratio of the images, could violate the direct or indirect copyrights of the
imaging software or broadcast program, etc., if done without first consulting with the
copyright holder. For this reason, please take appropriate measures before performing
one of the actions listed above, including obtaining a license from the copyright holder.
Serial No.
Retain this information for future reference.
Disposal
This product contains substances which are harmful to humans and the environment.
• Solder used in the internal parts contains the lead.
• The lamp contains inorganic mercury.
Please dispose of this product or used lamps in accordance with local regulations.
Trademarks
• VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of
International Business Machines Corporation.
• Macintosh is a registered trademark of Apple Computer, Inc.
• Windows is a registered trademark of Microsoft Corporation in the U.S. and other
countries.
• Adobe is a registered trademark and Acrobat Reader is a trademark of Adobe Systems
Incorporated.
Notational Conventions Used in This Manual
References to pages with related information are annotated as follows.
For example, if making a reference to page 36: p.36
10
11
Before Using
IMPORTANT PRECAUTIONS (Continued)
Before Using
Mainenance
SAFETY PRECAUTIONS ................................................................................ 2
IMPORTANT SAFETY INSTRUCTIONS ......................................................... 3
LABEL LOCATIONS ........................................................................................ 8
POWER SUPPLY CORD SELECTION ............................................................ 9
IMPORTANT PRECAUTIONS ......................................................................... 9
EXEMPTION CLAUSES ................................................................................ 11
OTHER CAUTIONS AND INFORMATIONS .................................................. 11
CONTENTS ................................................................................................... 12
Preparations
Checking the package contents ..................................................................... 14
Names of each part on the main unit ............................................................. 15
Names of each part on the control panel and remote control ........................ 16
Names of each part on the document camera
(models with a document camera) ................................................................. 17
Preparing and using the remote control ......................................................... 18
Placement ...................................................................................................... 19
Connection ..................................................................................................... 21
Air filter cleaning ............................................................................................ 39
Lens and main unit cleaning .......................................................................... 40
Lamp replacement ......................................................................................... 40
Others
Trouble indications ......................................................................................... 42
Before calling service personnel .................................................................... 43
Specifications ................................................................................................. 45
List of general specifications ...................................................................... 45
Document camera specifications
(Models equipped with document camera) ................................................ 45
List of supported signals (RGB signals) ..................................................... 46
List of supported signals (Y/PB/PR signals) ................................................ 47
List of supported signals (Video, S-Video signals) ..................................... 47
Pin assignment of COMPUTER & MONITOR terminals ............................ 47
CONTROL terminal .................................................................................... 48
Separately Sold Product ............................................................................. 48
Operations
Turning the power on and off ......................................................................... 22
Basic operations ............................................................................................ 24
Using handy features ..................................................................................... 26
Using auto setting (Auto setting) ................................................................ 26
Correcting the keystone distortion (Keystone) ............................................ 27
Zooming out the images ............................................................................. 27
Cutting off the picture and sound temporarily (Mute) ................................. 28
Freezing the image (Freeze) ...................................................................... 28
Enlarging the picture size (Resize) ............................................................. 29
Displaying Information [Status display] ....................................................... 30
Using the menus ............................................................................................ 31
How to use the menus ................................................................................ 31
The image adjustment menu ...................................................................... 32
The default setting menu ............................................................................ 32
The display setting menu ............................................................................ 33
Reset menu (Special menu) ....................................................................... 33
Using the document camera .......................................................................... 34
Uninstalling the camera .............................................................................. 34
Installing the camera .................................................................................. 34
Preparation of the document camera (when loading the camera).............. 35
Preparing the document camera
(for use being separated from the projector) .............................................. 35
Image projection with the document camera .............................................. 36
Locking the white balance .......................................................................... 38
12
13
Before Using
CONTENTS
Preparations
Checking the package contents
Names of each part on the main unit
Please make sure that the following items are included in the box, along with the main unit. If
any item is missing, please contact the store immediately where you purchased the product.
(6)
(11)
(11)
(5)
(10)
(6)
(9)
(2)
(7)
(12)
(6) (7)
(3)
(8)
(17) (18)(19) (20)(21)(22)
(8)
AUDIO
(9)
(5)
(10)
MONITOR
COMPUTER( Y/PB/PR )
VIDEO
VIDEO
S-VIDEO
CONTROL
(13)
T
TER
R-CL
INPU
U/EN
■ (1) Remote control
■ (2) R03 (SIZE AAA) batteries for remote
control (2)
■ (3) Quick Reference
■ (4) CD-ROM
■ (5) Owner’s Manual
■ (6) Power cord (See note)
■ (7) RGB cable
■ (8) Video cable
■ (9) Audio cable (for computer)
E
MOD
STOP
PJ
VOL.
-
MEN
ICK
PLAY
LASE
R
(4)
(1) (14)(15)(16) (14)
(13)
■ (10) Audio cable
■ (11) Camera extension cable
(supplied with the document camera)
■ (12) Carrying bag
■ (13) Mouse remote control set (*)
• Mouse remote control
• R03 (SIZE AAA) batteries for
mouse remote control (2)
• Mouse remote control receiver
• Mouse remote control manual
(*) Supplied with TLP-T60M, TLP-T61M,
TLP-T70M, TLP-T71M
Note
The shape and number of supplied power cords vary depending on the product destination.
◆The Supplied CD-ROM
The supplied CD-ROM contains an owner’s manual, including information omitted in this
Owner’s manual (Getting started) and Acrobat® Reader™ to view the manual.
■ Installing Acrobat® Reader™
Windows®: Run the CD-ROM, select the Reader/English folder, and run ar500enu.exe.
Follow the on-screen instructions.
Macintosh: Run the CD-ROM, select the Reader/English folder, and run Reader
Installer. Follow the on-screen instructions to install the software.
■ Viewing the manual
Run the CD-ROM and double-click on Start.pdf. Acrobat® Reader™ launches, and the
menu screen of the Owner’s manual appears. Click on your language. The Owner’s
Manual cover and list of bookmarks appear. Click on a bookmark title to view that
to view a reference page with related information.
section of the manual. Click on p.
See the Help menu for more information about Acrobat® Reader™.
14
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
Name
Infrared remote sensor
Lens
Zooming lever
Focusing ring
Air intake
Tilt adjuster
Lamp cover
AC IN socket
Foot adjuster
Foot adjuster release button
Control panel
Camera input terminal*
Camera mounting stays*
Air exhaust
Speaker
Anti-theft lock hole
AUDIO terminal
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
(18) MONITOR terminal
(19) COMPUTER terminal
:
:
(20) VIDEO terminal
(21) S-VIDEO terminal
(22) CONTROL terminal
:
:
:
Function
Senses commands from the remote control. p.18
Projects expanded image.
Adjusts screen size. p.25
Adjusts screen focus. p.25
Draws in air from outside unit.
Adjusts the projector’s horizontal tilt. p.25
Remove to replace lamp. p.41
Connect the supplied power cord here. p.22
Adjusts the vertical projection angle. p.25
Press to stow the foot adjuster. p.25
Operates the projector. p.16
Connect the camera. p.34 p.35
Hold the camera control panel. p.34
Expels air that has grown hot inside the projector.
Plays audio.
Attach a security chain, etc. here.
Feeds the audio signal from a computer or video
equipment.
Connected to the monitor display.
Feeds the RBG signal from a computer or the component video signal (Y/PB/PR) from a video equipment.
Feeds the video signal from a video equipment.
Feeds the S-video signal from a video equipment.
Connected to the RS-232C port on a controlling
computer for operating the projector. p.48
Note
*: For the models with a document camera
15
Preparations
(1)
(12)
(5) (4) (3) (2) (1)
Names of each part on the control panel and remote control
Control panel
Remote Control
CLASS 1 LED PRODUCT
(15)
(1)
AUTO
(12)
(13)
SET
(8)
(7)
(4)
MUTE
(11)
(5)
FREEZE
(10)
(12)
(11)
ON
(4)
(2)
(3)
ON/
STANDBY
(3)
(7) (8) (9) (10)
(1)
Remote control transmitter
CALL
KEYSTONE
FAN TEMP LAMP
Names of each part on the document camera (models with a document camera)
INPUT
(2)
(13)
ON / STANDBY
(1)
ZOOM +
(8)
(6)
CANCEL
(9)
(14)
INPUT
MENU
VOL. -
(2)
(6)
ZOOM +
VOL. +
(3)
VOL.-
(5)
AUTO
KEYSTONE
MENU
AUTO SET
ZOOM -
VOL.+
(5)
(6)
(4)
ZOOM -
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
Name
ON/STANDBY button
INPUT button
AUTO KEYSTONE button
AUTO SET button
MENU button
Selection buttons
FAN indicator
TEMP indicator
LAMP indicator
ON indicator
MUTE button
FREEZE button
RESIZE buttons
CANCEL button
CALL button
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Main Function
Turns the power on/off (standby). p.22
Selects input. p.24
Adjusts keystone (trapezoidal distortion). p.27
Sets up image and mode. p.26
Displays menus and makes selections. p.31
Menu selections and adjustments, etc. p.31
Displays cooling fan mode. p.23 p.42
Lights when internal temperature too high. p.42
Displays lamp mode. p.23
Displays whether power is on or off. p.22
Cuts off the picture and sound temporarily. p.28
Pauses image. p.28
Enlarges picture size. p.29
Exiting the operation. p.30
Displays the information on the screen. p.30
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Name
Camera head
Camera lens
Focus ring
Camera arm
CAMERA GAIN buttons
CAMERA button
Tip resistant bar
(8) Stay mounting holes
(9) Camera output terminal
(CAMERA OUT)
(10)
(11)
(12)
(13)
Lock bar
Connector
Connect lever
Lock lever
:
:
:
:
:
:
:
:
Function
Document camera.
Shooting lens for the document camera.
Adjusts the focus.
Adjusts the shooting angle. p.36
Adjusts the camera gain. p.37
Toggles between the camera input and previous input. p.36
Pulled out when a camera is used separated from the
projector.
: Aligns with the projector's stay.
: Connected to the accessory camera cable when a
camera is used separated from the projector.
: Locked to the projector.
: Camera signal is output.
: Connector is connected to the projector.
: Used when the camera is disconnected from the
projector.
Notes
• For the remainder of this manual, buttons are referred to as follows:
Selection buttons ⇒
; MENU button ⇒
• For further information of the mouse remote control supplied with the TLP-T60M, TLPT61M, TLP-T70M, TLP-T71M, see the Owner’s Manual of the Mouse Remote Control.
16
17
Preparations
RESIZE
Preparing and using the remote control
Placement
■ Loading dry-cell batteries
into the remote control
■ Operating the remote
control
Placement Styles
q Remove the battery cover.
Point the remote control toward the
projector’s infrared remote sensor,
and press a button on the remote
control.
As shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the placement style in the
default setting menu p.32 , in accordance with your needs.
Floor-mounted front projection
Floor-mounted rear projection
w Insert the dry-cell batteries.
AC IN
Be sure to align the plus and minus
ends of the batteries properly.
Approx. 15°
App
r
ox.
5m
Ceiling-mounted front projection
Ceiling-mounted rear projection
AC IN
• Operating the projector from the rear
Two batteries (R03, SIZE AAA) are
used.
e Replace the battery cover.
Approx. 15°
Ap
pro
x
.5
m
Dry-cell batteries
• Before using the batteries, be sure to observe the Safety Precautions described in
previous pages.
• Remove batteries from remote control when not using for extended periods.
• If the remote control stops working, or if its range decreases, replace all the batteries with
new ones.
CAUTION
• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when
placing the unit.
• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so.
Mounting the projector on a ceiling requires special ceiling brackets (sold separately)
and specialized knowledge. Improper mounting could cause the projector to fall,
resulting in an accident.
• If the projector is ceiling-mounted, install the breaker for turning off the power in case of
anomaly. Let everyone involved with the use of the projector know that.fact.
The remote control
• The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
• Do not drop or bang.
• Do not leave in hot or humid locations.
• Do not get wet or place on top of wet objects.
• Do not take apart.
• In rare cases, ambient conditions could impede the operation of the remote control. If this
happens, point the remote control at the main unit again, and repeat the operation.
• For further information of the mouse remote control supplied with the TLP-T60M, TLPT61M, TLP-T70M, TLP-T71M, see the Owner’s Manual of the Mouse Remote Control.
18
19
Preparations
• Operating the projector from the front
Placement (Continued)
Connection
Projection Distance and Screen Size (with optical zooming)
Before connection
Use the figures, tables, and formulas below to determine the screen size and projection
distance. (Screen sizes are approximate values for full-size picture with no keystone adjustment)
• Read the owner’s manual of the device to connect to the projector.
• Some types of computer cannot be used or connected to this projector.
Check for an RGB output terminal, supported signal p.46 , etc.
• Turn off the power of both devices before connecting.
• The figure below is a sample connection. This does not mean that all of these devices
can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)
Screen
As seen from above
As seen from the side
Lens center
90°
Computer
CRT monitor, etc.
Preparations
90°
a
For TLP-T70M/T71M
a (min length) =
a (max length) =
projection size (inches) – 1.547
26.44
For TLP-T60M/T61M/S40/S41
a (min length) =
projection size (inches) – 1.4285
projection size (inches) – 1.2907
projection size (inches) – 1.1908
a (max length) =
22.06
25.574
a is the distance (m) between the lens and
the screen, and corresponds to a range of
1.45 m to 11.29 m.
To audio output
30.68
Audio cable
(for computer)
(supplied)
To RGB
output
a is the distance (m) between the lens and
the screen, and corresponds to a range of
1.26 m to 9.73 m.
RGB cable
(supplied)
AUDIO
screen
size (cm)
40 (102)
60 (152)
80 (203)
100 (254)
150 (381)
200 (508)
250 (635)
300 (762)
projection distance a(m)
min length
max length
(zooming max) (zooming min)
1.45
1.75
2.21
2.66
2.97
3.57
3.72
4.47
5.61
6.74
7.51
9.01
9.40
11.27
11.29
—
screen
size (cm)
40 (102)
60 (152)
80 (203)
100 (254)
150 (381)
200 (508)
250 (635)
300 (762)
projection distance a(m)
min length
max length
(zooming max) (zooming min)
1.26
1.52
1.91
2.30
2.56
3.08
3.21
3.86
4.84
5.82
6.47
7.77
8.10
9.73
9.73
—
COMPUTER( Y/PB/PR )
MONITOR
VIDEO
VIDEO
S-VIDEO
CONTROL
Monitor cable
Mini D-sub 15P-BNC
(not supplied)
Audio cable
(supplied)
S-Video cable
(not supplied)
To Y/CB/CR output
Green (Y)
Blue (CB),
Red (CR)
Control cable
Video cable
(supplied)
Yellow
(to video output)
To audio
p48
Conversion output
adapter
White (L)
Red (R)
BNC-pin
(not supplied)
To audio
output
White (L)
Red (R)
DVD player
To S-Video
output
VCR
To RS-232C terminal
Computer (for control)
Note
• The AUDIO terminal can be used with all the devices for input terminal.
20
21
Operations
Turning the power on and off
Connecting the power cord
Turning the power off
1
2
1
Insert the power cord plug into a wall or other power outlet.
When the power cord is plugged in, the following
three green indicators will come on for several
seconds: ON, TEMP, and LAMP. Next, the ON
indicator will change to orange, indicating standby
mode.
(Do not perform any operations while the 3 green
indicators are on.)
(Supplied) Power cord connector
Press the ON/STANDBY button.
A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button again.
The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
When cooling lamp
FAN
Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat.
■ Turning the power on
Press the ON/STANDBY
button.
The power turns on, and the following
3 green indicators light: ON, LAMP,
and FAN. After a moment, the startup screen appears.
TEMP LAMP
(Green)
Control panel
FAN TEMP LAMP
Remote
Control
ON
ON/
STANDBY
CALL
INPUT
ON / STANDBY
KEYSTONE
AUTO
SET
ZOOM +
MUTE
FREEZE
MENU
RESIZE
VOL. -
ON
(Green) (Orange)
Flashing
A
During internal cooling
FAN
(Green)
TEMP LAMP
(Off)
B
After cooling is completed
ON
FAN
(Orange)
(Off)
TEMP LAMP
(Off)
ON
(Orange)
C
A
During cooling, the LAMP indicator flashes. In this state, the power cannot be
turned back on. In addition, unplugging the power cord in this state will shorten
the life of the lamp.
B
After the LAMP indicator goes off, the cooling fan continues to operate for a
short while in order to expel excess internal heat. If you are in a hurry, there is
no problem with unplugging the power cord in this state.
C
In standby mode.
Note
• The projector consumes about 6W of power in standby. We recommend you to unplug the
power cord if you will not use the projector for an extended period.
VOL. +
AUTO
KEYSTONE
PRECAUTIONS
RESIZE
OFF
AUTO SET
ZOOM -
INPUT
WARNING
• Do not look into the lens during operation. Doing so could damage your vision.
CAUTION
• Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
• Do not place your hands, face, or other objects near the air exhaust. Doing so could
cause burns, deform/break the object.
Notes
• The start-up screen will disappear after a moment. You can dismiss the start-up screen before this
by performing any operation. You can also configure the start-up screen not to appear via the
Display setting menu p.33 .
• The first time you use the projector after purchase, after the start-up screen disappears, the
Language menu is displayed p.24 .
22
• Before unplugging the power cord, make sure that the LAMP indicator is off. Unplugging
the power cord and cutting off the power while the projector is running or being cooled
will shorten the life of the lamp. However, please unplug the power cord if the
projector locks up or acts abnormally.
• If the power cord was unplugged before cooling was complete, give the lamp sufficient
time to cool before plugging it back in. If the lamp overheats, it may fail to light, and its
lifetime will be shortened.
LCD Panels
LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the
following precautions.
• In order to extend the lifetime of the LCD panel, always turn off the power when not in
use, and make sure that the lamp is off. Keeping the lamp off is also very effective at
saving electricity.
• If the air filter becomes dirty and clogged, the projector’s internal temperature will rise,
shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter
from time to time p.39 , and replace it periodically. Contact the store where you
purchased your projector, or your local Service Station for replacement air filters.
23
Operations
Insert the power cord connector into the AC IN socket of the projector.
Basic operations
5 Projector placement angle adjustments
Turn on the power by following the instructions in “Turning on the power” p.22 .
2 Select the language and the lamp power (When using the
first time).
When the projector is used for the first time after purchase, menu for language and
lamp power selection and configuration is displayed in English. (If the screen is out of
focus, adjust it according to the step 6 .)
q Use the
or
buttons to select the
desired language and press the
button.
Message for setup confirmation is displayed in a
selected language.
w Using the
or
button, select Standard
or Low and press the
button.
The lamp power, if selected, will be toggled without
button. The display automatically
pressing the
disappears in a few seconds.
English ................ English
Français .............. French
Deutsch .............. German
Italiano ................ Italian
Español ............... Spanish
Português .......... Portuguese
................... Japanese
....... Chinese (simplified)
....... Chinese (traditional)
................... Korean
Notes
• When the projector is turned on the next time, the Language and Lamp power
menus do not appear upon startup. However, if “Reset all” is executed from the
Reset menu p.33 , the Language and Lamp power menus will be displayed the next
time when the power is turned on
• The language can also be set via the Display setting menu p.33 and Lamp power
via the Default setting menu p.32 .
• This owner’s manual assumes that English has been selected.
3 Place connected device(s) in operating status.
Turn on and boot up connected computers and other devices.
4 Select input.
q Press the INPUT button.
A list of inputs appears on the screen.
w Use the
buttons to select the desired
input, and press the
button.
The picture for the selected input is projected.
Computer
Y/PB/PR
Video
S-video
When a camera is
connected with the
document camera model:
Computer
Y/PB/PR
Video
S-video
Camera
24
The placement angle and the height of the projected image can be adjusted by the foot
adjuster.
q Lift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
1
The foot adjuster extends. Release the
button to lock the position.
w Turn the foot adjuster to fine-tune
the angle.
e To adjust the horizontal angle, use
the tilt adjuster.
3
2
To stow the foot adjuster, hold up the projector while pressing the foot adjuster
release button, then slowly lower the projector.
6 Adjusting the picture size and focus
q Use the zooming lever to adjust the screen
size.
w Use the focusing ring to adjust the focus.
7 Adjusting the volume with the
1
2
buttons
The speaker volume can be adjusted when an audio signal is being input.
Notes
• Note that because of the lamp characteristics, the brightness of the lamp may fluctuate slightly.
• A lamp is a consumable supply.
If used for extended periods, images will appear dark, and the lamp could burn out. This
is characteristic of a lamp, and is not malfunction. (The lifetime of the lamp depends on
conditions of use.)
• The LCD panel is made using extremely advanced technology, but there may be black
spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.
Please note that these are not malfunctions.
• Although this projector supports a wide range of RGB signals p.46 , any resolutions not
supported by the model (XGA or SVGA, depending on the model) will expand or shrink the
pictures, and will affect image quality slightly. To view high-quality images, it is
recommended that the computer’s external output should be set to the projector’s resolution.
• With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may cause the images to be
shown improperly. If this happens, turn off the computer’s LCD display. For information on
how to turn off the LCD display, see the owner’s manual of your computer.
• If a signal not supported by the projector is input, the
icon will appear.
icon will appear.
• If a no signal is being input from the connected device, the
• If an unavailable operation button is pressed, the
icon will appear.
25
Operations
1 Turn on the power.
Using handy features
■ Using auto setting (Auto setting)
■ Correcting the keystone distortion (Keystone)
This function sets up the projector to the optimum state for
each type of the input signal by using simple operations. Control panel
FAN TEMP LAMP
1 Press the AUTO SET button.
Remote
Control
ON
ON/
STANDBY
CALL
INPUT
ON / STANDBY
KEYSTONE
AUTO
SET
When the foot adjuster p.25 is used to change the
projection angle, the picture will undergo keystone (trap- Control panel
ezoidal) distortion.
This projector is capable of correcting this keystone distortion.
FAN TEMP LAMP
INPUT
ZOOM +
The Auto setting menu appears.
ON
MUTE
Before correction
RESIZE
VOL. -
The menu item is automatically adjusted/set.
icon will appear during
For computer input, the
processing.
AUTO SET
RESIZE
OFF
AUTO SET
INPUT
ZOOM -
1 Press the AUTO KEYSTONE button.
The Keystone menu appears.
2 Press the AUTO KEYSTONE button again.
icon will appear during processing.
● Manual adjustment
Use the
press the
buttons for keystone adjustment. When the adjustment is finished,
button. The menu disappears. (The CANCEL button on the remote
control also allows you to exit the menu mode.)
Description
Adjust with
The keystone distortion is automatically corrected. The
Item
to eliminate flicker.
Frequency
Adjust with
to eliminate periodic patterns and
flickering when many vertical lines appear on the screen.
H-position
Move left
Move right
V-position
Move up
Move down
Clamp 1
Adjusts the clamp pulse position with
Clamp 2
Adjusts the clamp pulse width with
or
or
.
.
Phase
Adjust with
to eliminate flicker.
Signal format [ : Enter to setting mode] [
: Select one
of the following] [Apply: ]
480i(525i)@60Hz/480p(525p)@60Hz/
576i(625i)@50Hz/576p(625p)@50Hz/
720p(750p)@60Hz/720p(750p)@50Hz/
1080i(1125i)@60Hz/1080i(1125i)@50Hz/
1035i(1125i)@60Hz/1152i(1250i)@50Hz
Video mode
[ : Enter to setting mode] [
: Select one
of the followings] [Apply: ]
NTSC/PAL/SECAM/PAL-N/PAL-M/PAL60/NTSC4.43
Keystone
Description
Shrink button of the screen
Shrink top of the screen
Notes
• Depending on the amount of keystone adjustment and the content of images, some
information may be lost, or the picture quality may suffer.
• Keystone adjustment will not change the shape of the menus.
■ Zooming out the images
This equipment is provided with the digital zoom (electric zoom) (100-80%) capability in
addition to the optical zoom.
You can use the digital zoom in applications where the optical zoom is not applicable
due to some physical reasons for installations (Note, however, that digitally zoomed
display suffers from some degradation).
1 Press the ZOOM – button.
Each time the ZOOM – button is pressed, the
image is reduced in size.
Control panel
RESIZE
FAN TEMP LAMP
INPUT
ON
ON / STANDBY
CANCEL
ZOOM+
INPUT
ZOOM+
MENU
VOL. -
Note
VOL. +
AUTO
KEYSTONE
27
VOL.-
MENU
AUTO SET
ZOOM-
• Moving pictures generated with the DVD software for computers may appear
unnatural if it is projected with this projector, but it is not a malfunction.
26
Remote
Control
ZOOM-
VOL.+
Operations
Item
Select Item
VOL. +
AUTO
KEYSTONE
INPUT
ZOOM -
The menu items vary depending on the input type, as shown in the table below.
buttons to adjust the items in the table below, then press
Use the
the
button when you are finished. The menu disappears. (The CANCEL button
on the remote control also allows you to exit the menu mode.)
Select Item
FREEZE
MENU
RESIZE
OFF
AUTO
KEYSTONE
● Manual adjustment and setting
Video
S-video
SET
RESIZE
• Auto adjustment/setting may not be performed correctly for input signals other than
those supported by the projector p.46 , p.47 .
Y/PB/PR
AUTO
MUTE
After correction
VOL. +
Note
Phase
KEYSTONE
FREEZE
MENU
VOL. -
Computer
ON/
STANDBY
CALL
ON / STANDBY
ZOOM +
2 Press the AUTO SET button again.
Input
Remote
Control
Using handy features (Continued)
2 Press the ZOOM + button to bring it back to the original size.
■ Enlarging the picture size (Resize)
Each time the ZOOM + button is pressed, the image size increases.
(You cannot make it larger than the original size.)
The image being projected can be enlarged.
1 Press the remote control’s RESIZE
button.
The enlargement ratio is increased each time the RESIZE
button is pressed.
2 To decrease the enlargement ratio, press the remote control’s
• Pressing either the ZOOM- or ZOOM+ button would display the
• The adjustment value will automatically be saved.
RESIZE
icon.
■ Cutting off the picture and sound temporarily (Mute)
When you want to project the images of another projector, overhead
projector, etc. temporarily, this projector’s images and sound can be
turned off.
Press the remote control’s MUTE button.
The picture and sound are cut off. The Mute function is released
when pressing the MUTE button again. To cancel the command,
press the CANCEL button.
button.
The enlargement ratio is decreased each time the RESIZE
(The image cannot be shrunk to less than its original size.)
Remote
Control
ON/
STANDBY
CALL
KEYSTONE
AUTO
SET
MUTE
button is pressed.
Remote
Control
3 Press and hold down the
buttons to
move the enlarged area.
RESIZE
2
4
1
CANCEL
INPUT
ZOOM +
FREEZE
VOL.-
MENU
RESIZE
VOL.+
3
RESIZE
OFF
Notes
ZOOM INPUT
• The
icon will appear while mute is in effect.
• Operating any other functions cancel the muting.
■ Freezing the image (Freeze)
Remote
Control
ON/
STANDBY
CALL
The image being projected can be made to be frozen. This function is to
be used to pause a video during a presentation, etc.
KEYSTONE
AUTO
MUTE
The picture pauses. The Freeze function is released when pressing
the FREEZE button again. To cancel the command, press the
CANCEL button.
FREEZE
RESIZE
OFF
INPUT
Notes
• The
icon will appear while freeze is in effect.
• The freeze function can be used on the resize function. Other operations will
release the freeze.
• Even if an image is frozen on the projector, the pictures are running on the video or
other equipment.
• If you use this function on video soft sold on the market, broadcast or broadcast on
cable except for the purpose of your private viewing and listening, it may infringe
the copyright protected by the copyright laws.
28
The resize is released, and the image returns to its original size.
Notes
SET
RESIZE
Press the remote control’s FREEZE button.
4 Press the CANCEL button to undo the resize.
• The
icon will appear while resize is in effect.
• An enlarged image can be frozen using the FREEZE button. The resize function on
a frozen image can also be used.
• Operations other than freeze will cancel the resize.
• Since the enlargement is performed using digital processing, enlarging will cause
the image to appear jagged.
• Rarely, the picture could become garbled while the enlarged area is being moved.
• If you use this function on video soft sold on the market, broadcast or broadcast on
cable except for the purpose of your private viewing and listening, it may infringe
the copyright protected by the copyright laws.
29
Operations
Notes
Using handy features (Continued)
Using the menus
■ Displaying Information [Status display]
You can call up on-screen menus, and conduct a number of adjustments and settings using
the operation buttons p.16 on the control panel (main unit side) and remote control.
This displays information about the input signal, lamp use time, etc.
Press the
button twice (or press the CALL button on the remote
control once).
Remote
FAN TEMP LAMP
Control
ON
ON/
STANDBY
CALL
INPUT
ON / STANDBY
KEYSTONE
AUTO
SET
Description
Input
RGB signal mode
H-resolution
V-resolution
H-frequency
V-frequency
Sync
Signal format
Video mode
Lamp time
Version
Input source name
RGB input mode [Note 1]
Horizontal resolution (in bits)
Vertical resolution (in bits)
Horizontal sync frequency
Vertical sync frequency [Note 2]
Sync signal polarity [Note 3]
Y/PB/PR signal format
Color method of video signal
Time of lamp use [Note 4]
Firmware version [Note 5]
MUTE
FREEZE
MENU
RESIZE
VOL. -
RESIZE
OFF
AUTO
KEYSTONE
Select a category by using
.
Displays the current
adjustments of selected
category.
Item shown with gray
cannot be adjusted with
the current input source.
There are following three
categorys.
VOL. +
AUTO SET
INPUT
ZOOM -
Image adjustment menu p.32
Computer Y/PB/PR
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
No
No
No
No
No
No
Yes
No
Yes
Yes
Video
S-video
Yes
No
No
No
No
No
No
No
Yes
Yes
Yes
Camera
Yes
No
No
No
No
No
No
No
No
Yes
Yes
Notes
1: The mode of supported RGB signals p.46 is shown.
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the displayed time approaches 3,000
hours, consult with a store about getting a TLPLV2 replacement lamp (sold separately)
prepared.
5: [Version] shows the version of the projector’s internal control program. This version is
referred to for customer service, etc.
Notes
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
• Conducting another operation while information is being displayed dismisses the
display.
30
2. Select a Category
ZOOM +
“Yes”: displayed, “No”: not displayed
Item
The menu shown below is only for operation instructions and might be different from the
actual display.
Display the Setting display menu
1. Start
Default setting menu
p.32
Display setting menu
p.33
3. Adjustments & Settings
Press
to open the menu
of the selected category.
5. To Finish
Item
Adjustment/Setting Value
These marks signify the
items can be adjusted/set
by using
.
These marks signify an
item can be switched by
using
.
Finish via the Status
display menu.
This mark signfy that
there are options.
Press
to display a
list of options.
To Status display
p.30
The figure shows a typical example.
As the display may differ depending
on the item, use the following pages
as a reference.
These marks signify the items can be selected from
the list by using
.
After an item is selected, apply it by pressing
.
6. End
The menu disappears.
4. Back
Note
• Menu adjustments and settings are saved when the power is turned off via the ON/
STANDBY button. If the power cable is disconnected before this, or the power goes out,
then the data will not be saved.
• You can also use the CANCEL button on the remote control to dismiss the menu display.
31
Operations
When the
button is pressed once, the Setting
display menu appears. Pressing it again displays
information p.31 . The table below shows what kind
button (or
of information is displayed. Press the
press the CALL or CANCEL button on the remote
control to serve the same purpose) again to
dismiss the display.
Control panel
■ How to use the menus
Using the menu (Continued)
■ The image adjustment menu
■ The display setting menu
Use this menu to adjust image-related items.
Items that can be adjusted are marked with “Yes”, and those that cannot are marked with “No”.
Use this menu to set screen display-related items.
Description
Computer Y/PB/PR Video S-video Camera
Contrast
Lower
Higher
Yes
Yes
Yes
Yes
Yes
Brightness
Darker
Brighter
Yes
Yes
Yes
Yes
Yes
Lighter
Deeper
No
Yes
Yes
Yes
No
Greenish
No
No
Yes
Yes
No
Sharper
No
Yes
Yes
Yes
Yes
Less red
More red
Yes
Yes
Yes
Yes
Yes
G-level
Less green
More green
Yes
Yes
Yes
Yes
Yes
B-level
Less blue
More blue
Yes
Yes
Yes
Yes
Yes
Shift up
No
Yes
Yes
Yes
No
Color
Tint [Note 1]
Sharpness
R-level
Reddish
Softer
Up/down shift [Note 2] Shift down
Notes
1: Tint can only be adjusted when Video mode p.26 is set to NTSC or NTSC4.43.
2: Up/down shift can only be adjusted when Screen size p.33 is set Wide.
This menu shows placement status and other settings.
Description
Item
Projection
mode
Sets projection mode in accordance with Placement Style p.19
No signal
power off
Sets the period of time to wait until turning off the power after signal input stops:
Off (not turned off)
1 min
2 min
...
60 min
Power on
Sets whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto). Manual
Auto
(Rear)
(Hung from
ceiling)
Standard
Lamp power [Note 1] Sets the lamp power
Sets the camera’s shutter speed to either (50Hz) or (60Hz). 50Hz
Shutter speed
White balance
[Note 2]
Sets the camera’s white balance to (Auto) or (Fixed). Auto
Screen size
(Full): Display with LCD panel’s resolution
(Thru): Display with sampling resolution (for computer input)
(Wide): Wide-screen display (for Video, S-video, and Y/PB/PR)
Language
Select one of the languages below to use for displaying menus and messages
[ : Enter setting mode] [
:Selection]
[Apply:
]
English/Français/Deutsch/Italiano/Español/
Português/
/
/
/
Background
Screen to display when there is no input signal
Icon
Display icons as function guides
On
Off
Start-up screen
Display start-up screen when power turned on
On
Off
(Back hung
from ceiling)
Low
60Hz.
Fixed.
Notes
1: When lamp power is set to low, the screen becomes a little darker, but the cooling fan noise gets
quieter. This setting will be cleared when you turn the power off. The setting will be back to
“Standard” when the power is turned on next time.
2: White balance, if set to Fixed, is reset upon power off and the Auto is resumed the next time the
unit is turned on. (Models with the document camera)
Notes
(Blue)
(None)
• If “Thru” is selected for screen size, portions exceeding the pixel count of the LCD panel
p.45 will not appear on the screen. Note that for RGB signals with clock speeds
SXGA3_60 p.46 or lower, all input pixel signals are sampled. (This effect is noticeable
when the screen is enlarged using the Resize function p.29 ). However, if the clock speed
is higher than this, the RGB pixel signal is reduced before sampling.
• Displaying the images with the aspect ratio different from the original with the purpose of
other than the personal and private viewing, using the screen size menu may violate the
copyright protected by the law.
■ Reset menu (Special menu)
When other menus are not displayed and the
button is held down, the menu appears.
• When the screen is placed vertically, and Auto keystone correction is executed, but the
keystone correction is not successful, stow the foot adjuster in its original position, place
the projector on a flat surface, select Horizontal reference value reset, and press the
button.
• Select Reset All and press the
button to return all menu items to the factory settings.
Item
Description
Horizontal reference Reset the horizontal reference value for Auto keystone correction
[ : Enter execution mode] [Yes
No] [Apply: ]
value reset
Reset all
• Note that if Power on is set to Auto, then if the power cord is plugged in when power is
restored after a power outage, the projector power will come on.
• Even if Power on is set to Auto, press the ON/STANDBY button to turn off the power.
Unplugging the power cord to cut off the power will shorten the life of the lamp.
32
(Logo)
Notes
■ The default setting menu
(Placed
on floor)
Description
Item
Reset all menu items to their factory settings
[ : Enter execution mode] [Yes
No]
33
[Apply:
]
Operations
Item
Using the document camera
Please read this chapter if the model you purchased includes a document camera.
■ Uninstalling the camera
1) Place the folded document 2) Slide the connect lever in
camera with the bottom
the direction of an arrow.
side up.
■ Preparation of the document camera (when loading the camera)
Status before preparation
(When stowed)
1) Set up arm
3) Rotate arm
4) Raise camera head
2) Extend arm
3) Pressing the lock lever in
the direction of an arrow,
slide the document
camera.
■ Installing the camera
PRECAUTIONS
• Do not jolt or force the camera head or camera arm. Doing so could cause malfunction.
• Note that when extending or rotating the camera arm, the arm moves in an arc. Take care
not to bump yourself or others with it.
■ Preparing the document camera (for use being separated
from the projector)
• Before connecting the camera cable, make sure that the projector power is off.
1) Connect the supplied
camera cable to the
camera input terminal.
4) Slide the connect lever in
the direction of an arrow.
2) Connect the other end of
the camera cable to the
camera terminal on the
document camera.
3) Pull out the tip resistant bar
and set up the document
camera.
PRECAUTIONS
PRECAUTIONS
•
•
•
•
Before mounting or dismounting the document camera, disconnect the power plug.
Place a soft cloth beneath the projector when mounting or dismounting the camera.
Do not dismount or mount the document camera while the projector is upright or kept in the air.
Before mounting the camera, confirm that the interconnection connector is closed with
the connect lever. If you attempt to mount the camera with the connector being protruded,
connector may be damaged.
• When mounting the camera, be sure to slide the document camera until it is locked with
click sound.
• Confirm the four registration stays are aligned before sliding the camera.
34
• Insert a camera cable straight and securely until it locks. When disconnecting the cable,
pull it out releasing the lock on both sides of the plug.
• Be sure to pull the tip resistant bar fully until it forms the angle of 90 degree. If you don’t
use the bar, the camera may topple over.
• Note that the camera may tip over if you attempt to rotate the arm in the opposite side of
the tip resistant bar.
• For camera interconnection, be sure to use the supplied camera cable (1 m). If you use
the other cables, the normal operation cannot be achieved and even the malfunction may
result.
Note
• Connecting or disconnecting the camera cable with the projector's power ON may cause
is displayed) and even turn off the power.
camera error (
35
Operations
1) Place the folded document 2) Align the four registration 3) Slide the document
camera with the bottom
marks.
camera in the direction of
side up.
an arrow until it clicks.
Using the document camera (Continued)
■ Image projection with the document camera
1 Place the document.
5 Adjust the focus using the focus ring on the camera head
Rotate the focus ring to either NEAR or FAR, whichever is better in focusing.
Set the document at the top of or the side of the projector.
Turn the focusing ring to adjust
the focus.
• Near : 100 mm to 300 mm
Far : 300 mm to 5 m
6 If the screen is too dark or too bright, use the
2 Press the CAMERA button, and select camera input.
• The input returns to the previous input when the CAMERA
button is pressed again.
• Camera input can also be selected by pressing the remote
control or camera’s INPUT button.
CAMERA GAIN (+/–) buttons to make it easier to see.
The Sharpness of the camera image can also be adjusted using
the Image adjustment menu p.32 .
Fold up the camera using the opposite order from Preparation of the document camera.
shooting.
PRECAUTION
• If the room’s fluorescent lighting causes the image to flicker, either turn off the fluorescent
light, or set the Shutter speed from the Default menu p.32 . Note that changing the
Shutter speed setting may not eliminate the flicker, depending on the lighting, state of
the document, or image adjustment.
Note
• No audio is output when camera input is selected.
4 Move the camera head up and down to adjust the image size.
Farther: Smaller image
Closer: Larger image
• Closeup shot with the distance shorter than 100 mm cannot be performed.
36
37
Operations
7 After use, turn off the light, and fold up the document camera.
3 Rotate the camera lens to align the orientation of the document for
Mainenance
Using the document camera (Continued)
Air filter cleaning
■ Locking the white balance
The air filter prevents dust and debris from getting inside the projector. Never run the
projector with the filter removed. It is recommended that the air filter is cleaned regularly.
“Check the air filter for dirt.” is displayed every 100 hours. (If the
• The icon message
usage time exceeds 100 hours, this message is displayed for 30 seconds when the image is
displayed for the first time after power is turned on. This display will be dismissed with any
operation.)
• Check out the filter and any debris is found, use the following procedure for cleaning.
Although the projector’s camera is constantly adjusting the color balance of the images
it photographs, the color balance may be disrupted, depending on the color layout of
the document, etc. If this happens, the white balance can be locked using the procedures below.
1 Lay down a piece of white paper, and adjust so it fills the screen.
Adjust the camera head and arm so that the white paper fills
the screen completely.
WARNING
• Request cleaning and maintenance of a ceiling-mounted unit from your projector
dealership.
1 Unplug power cord.
2 Set the White balance to Lock in the
Default menu.
p.32
2 Remove the air filter.
Pull out the air filter by taking the catch shown in the figure.
The white balance is locked. If you want to return to the auto adjustment, set the White
balance to Auto in the Default menu.
Notes
• White balance setting to Fixed, if power is turned off, will be back to Auto.
• The color of the room lighting may prevent the white balance from being adjusted to the
optimum level. In this situation, or if you want to use a certain tinting, adjust the R-level,
G-level and B-level on the Image adjustment menu p.32 .
3 Clean the filter.
Carefully remove the dust and dirt from the air filter with a
vacuum cleaner or the like.
Maintenance
4 Replace the air filter.
Notes
• Allowing dirt and dust to build up in the air filter will worsen the air circulation inside the
projector, causing the internal temperature to rise, causing the projector to stop working
or malfunction.
• Insert the air filter all the way in. Leaving gaps will allow dust and dirt to get inside the
projector again.
• If you wash the air filer with water, make sure to dry it completely before replacing it.
• If the air filter is torn, consult with your dealer about replacing it with a new one.
Continuing to use a ripped filter will allow dust and dirt to get inside the projector.
38
39
Lens and main unit cleaning
Lamp replacement (Continued)
3 Remove the lamp cover.
WARNING
• Request cleaning and maintenance of a ceiling-mounted unit from your projector dealership.
■ Lens cleaning
• Clean the lens with a commercially available blower and/or
lens cleaner.
• The lens is easily scratched, so do not rub it with hard objects,
or strike it.
■ Main unit cleaning
• Clean the main unit after unplugging the power cord.
• Wipe dirt off the main unit gently with a soft cloth.
• If the soiling is severe, dip the cloth in a neutral
detergent diluted in water, wring well, and gently wipe
off the dirt, then finish up by wiping with a dry cloth.
● Replacing air intake and exhaust fans, and air filter
To maintain the performance, it is recommended that these should be replaced about
every 2 to 3 years. Consult with your dealer for details.
Lamp replacement
Loosen the 2 screws, then pull up to the
direction of the arrow with your fingers on the
area shown in the figure to remove the lamp
cover.
1
3
2
4 Pull out the lamp.
Loosen the 2 screws holding the lamp in place,
and pull up the handle to remove the lamp.
4
5 Mount the new lamp.
Align the orientation, press down until the bottom is
reached, and lock in place using the two lamp
locking screws.
1
2
6 Replace the lamp cover.
Align the cover, and press it in, then tighten the
screws loosened in step 3 until the lamp cover is
no longer loose.
2
5
1
7 Reset the lamp timer.
See the lamp’s manual for instructions on resetting
the lamp timer.
WARNING
• If the projector is mounted on a ceiling, request a lamp replacement from your projector dealership.
• When replacing, always use lamp “TLPLV2” (sold separately).
CAUTION
• If you have been using the projector, the lamp will be very hot, and may cause burn injuries.
Wait for the lamp to cool (for longer than 1 hour) before replacing it.
• If the lamp should break, please handle with care to avoid injury due to broken pieces
and contact your dealer for repair service.
1 Unplug power cord.
2 Wait until lamp is sufficiently cooled.
Notes and Precautions
• Press the
button twice to display (a rough guide) the time of lamp use, the Lamp time
item, in the Status display menu. p.30
• It is recommended that the lamp should be replaced after 3,000 hours of use. When
Lamp time reaches 3,000 hours, the
icon and a message will appear. This display
button.
disappears when you press
• Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the
lamp may fail to come on p.42 , and the lamp’s lifetime may be shortened.
• Always replace the lamp with a new one.
• The lamp is made out of glass. Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)
Used Lamps
This projector’s lamps contain trace amounts of environmentally harmful inorganic
mercury. Be careful not to break used lamps, and dispose it in accordance with local
regulations.
Wait for at least 1 hour.
40
41
Maintenance
A lamp is consumable supplies. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime
of the lamp depends on condition of use. If this happens, replace it with a new one.
Others
Trouble indications
Before calling service personnel
The indicator lights inform you of internal abnormalities.
If you think something is wrong, check the followings before contacting customer service.
Please see “Trouble indications” p.42 as well.
TEMP LAMP
ON
No power
⇒ Problem with projector
• Unplug the power cord, and contact your dealer.
(Off)
FAN
TEMP LAMP
ON
⇒ Lamp temperature is high so that it is difficult to turn on, the lifetime of
the lamp has ended or the projector is malfunctioning.
• Unplug the power cord and wait for a short while, then turn the power
back on.
• If a lamp burns out, replace it with a new one.
❈ After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
FAN
TEMP LAMP
ON
⇒ Internal overheating, or the outside temperature is too high.
• Place the projector so that the air intake and exhaust are not blocked.
• Unplug the power cord and wait for a short while, then turn the power
back on.
• Clean the air filter. p.39
❈ The
icon will appear before the power goes out.
❈ After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
Or
(Orange lit)
Or
(Off)
Or
(Green lit)
FAN
TEMP LAMP
ON
Power went out during use
⇒ Problem with internal cooling fan.
• Unplug the power cord, and contact your dealer.
❈ The
icon will appear before the power goes out.
❈ After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
(Red lit)
(Red lit or flashing)
Or
(Orange lit or flashing)
FAN
TEMP LAMP
ON
Power went out during use, or power won’t come on
⇒ The lamp cover is not properly attached.
• Unplug the power cord, and reattach the lamp cover. p.41
❈ After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
(Orange (Red lit)
flashing)
Model with a
document
camera
FAN
TEMP LAMP
(Green lit)
Power goes out
during use
• Is the ambient temperature high? p.42
• Is the air filter clogged? p.42
• Is the air intake or air exhaust blocked? p.42
No picture
•
•
•
•
•
Is the projector turned on? p.24
Is the mute function on? p.28
Is the brightness setting minimized? p.32
Are the connections set up correctly? p.21
Are all the connected devices functioning properly?
No audio
•
•
•
•
•
Is the projector turned on? p.24
Is the mute function on? p.28
Is the volume setting minimized? p.25
Are the connections set up correctly? p.21
Are all the connected devices functioning properly?
Picture not
displayed
correctly
•
•
•
•
•
Is the input signal supported by the projector? p.46 , p.47
Is the correct video mode selected? p.26
Is the correct signal format selected? p.26
Is the selecting of computer or Y/PB/PR input correct? p.24
Is there something generating an abnormal video signal, for
instance the video tape?
Picture blurred
Part of picture
out of focus
• Is the lens dirty? p.40
• Is the lens focus adjusted optimally? p.25
• Is the projection distance within the projector’s supported range?
Power went out during use
(Red lit)
Power went out during use
ON
(Red lit)
⇒ Camera is not correctly connected.
• Disconnect the power plug and check the connection with the camera.
❈ The
icon will appear before the power goes out.
❈ After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
PRECAUTIONS
• Make sure to unplug the power cord if something goes wrong.
• If the power cord is unplugged before cooling is complete, give the lamp enough time to
cool before plugging it back in. If the lamp overheats, it may fail to light. Unplugging the
power cord repeatedly when the temperature is high will shorten the life of the lamp.
(Even if you are not concerned about lamp lifetime, the light may not come on if you do
not wait at least 3 minutes.)
42
Check
• Is the power cord plugged in? Is it connected to the projector?
• Is the lamp cover loose? p.42
Lamp went out during use, or won’t come on
(Red lit) (Red lit)
(Green lit) (Red lit)
If This Happens
No power
p.20
• Is the projector’s screen placement angle tilted too far? p.19
• Are the sharpness or sampling phase adjustments off? p.26 p.32
Image is dark
• Are the brightness or contrast adjustments off? p.32
• Is the lamp nearing the end of its service life? p.30
Colors too light
Bad shading
• Are the color, tint, R-level, G-level, or B-level adjustments off?
• Is the screen dirty?
• Is the lamp nearing the end of its service life? p.30
Remote control
doesn’t work
•
•
•
•
p.32
Are the remote control’s batteries drained?
Are the batteries inserted into the remote control correctly? p.18
Is the remote control being used within the effective range? p.18
Are there any obstructions between the remote control and
projector?
• Are there any fluorescent or other bright lights shining at the
projector’s infrared remote sensor?
43
Others
FAN
Before calling service personnel (Continued)
If This Happens
Check
The images from the
document camera
are blurry
• Is the document imaging camera’s lens dirty?
• Is the document imaging camera out of focus? p.37
• Is the location of the object being focused too dark?
The images from the
document camera
are flickering
• Is there impact from the room’s fluorescent lighting?
Turn off the fluorescent lights, or change the shutter speed settings.
■ List of general specifications
Item
Specification
Consumption Power
265 W
TLP-T70M/T60M/S40: 2.3 kg
Weight
TLP-T71M/T61M/S41: 2.8 kg
Models without document imaging camera:
External Dimensions
303 × 84 × 206 mm (W × H × D)
(including protruding parts)
Models equipped with document imaging camera:
358 × 84 × 206 mm (W × H × D)
Cabinet material*
PC+ABS resin and ABS resin
Conditions for usage environment Temp: 0°C to 35°C; relative humidity: 30% to 70%
Display method 3-panel transmission
Panel size
0.7 type
LCD Panel Drive system
TFT active matrix
Picture
TLP-T series: 786,432 pixels (1,024H × 768V)
elements
TLP-S series: 480,000 pixels (800H × 600V)
Lens
Zoom lens
TLP-T60M/T61M/S40/S41
F=2.0-2.3 f=23.0-27.4 mm
TLP-T70M/T71M
F=1.8-2.1 f=26.5-31.5 mm
Lamp
High-pressure mercury lamp
Projection screen size
33-300 type
Projection distance
TLP-T60M/T61M/S40/S41 : 1.26-9.73 m
TLP-T70M/T71M
: 1.45-11.29 m
Speaker
1 W (Monaural)
COMPUTER terminal
Mini D sub 15 pin RGB / Y/PB/PR (dual use)
MONITOR terminal
Mini D sub 15 pin RGB / Y/PB/PR (dual use)
S-VIDEO terminal
Mini DIN 4 pin
VIDEO terminal
RCA Pin Jack, 1 V (p-p), 75 Ω
AUDIO terminal
3.5mm dia. stereo mini-jack, 1.5V (rms); 22 kΩ or more
CONTROL terminal
Mini DIN 8 pin (RS-232C)
Connection terminal
p.32
Specifications
* Each plastic part displays the materials it is made from, in order to facilitate recycling after this
product becomes no longer usable.
■ Document camera specifications
(Models equipped with document camera)
Lens
Focusing
Zooming
Image element
Effective pixels for pickup section
44
Specification
F=2.8, f=2.8mm
Switching in two steps
None (adjusted through distance from subject)
1/4.2 type honeycomb CCD
629,856 pixels (648H × 486V × 2)
45
Others
Item
Specifications (Continued)
■ List of supported signals (Y/PB/PR signals)
This projector supports the following RGB signals. Note, however, that depending on the
computer model, the screen may show flicker or streaking. Please adjust the projector if
this happens.
(Press the AUTO SET button, and adjust automatically or manually. p.26 )
Resolution
Mode
720 x 400
640 x 480
720x400_85
VGA_60
VGA_72
VGA_75
VGA_85
SVGA_56
SVGA_60
SVGA_72
SVGA_75
SVGA_85
MAC16"
XGA_43i
XGA_60
XGA_70
XGA_75
XGA_85
MAC19"
SXGA1_75
QuadVGA_60
QuadVGA_85
SXGA3_60
SXGA3_75
SXGA3_85
SXGA+
UXGA_60
UXGA_65
UXGA_70
UXGA_75
UXGA_85
1792x1344_60
1856x1392_60
1920x1440_60
800 x 600
832 x 624
1024 x 768
1152 x 864
1280 x 960
1280 x 1024
1400 x 1050
1600 x 1200
1792 x 1344
1856 x 1392
1920 x 1440
Refresh rate
(Hz)
85.039
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
74.550
86.957
60.004
70.069
75.029
84.997
74.700
75.000
60.000
85.002
60.020
75.025
85.024
60.012
60.000
65.000
70.000
75.000
85.000
60.000
60.000
60.000
H-frequency
(kHz)
37.927
31.469
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
49.725
35.522
48.363
56.476
60.023
68.667
60.134
67.500
60.000
85.938
63.981
79.976
91.146
63.973
75.000
81.250
87.500
93.750
106.250
83.640
86.333
90.000
Clock
(MHz)
35.500
25.175
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
57.283
44.900
65.000
75.000
78.750
94.500
79.857
108.000
108.000
148.500
108.000
135.000
157.500
118.094
162.000
175.500
189.000
202.500
229.500
204.750
218.250
234.000
Note
• Signals whose resolution exceeds the LCD panel’s number of pixels p.45 will be
compressed. For this reason, some information may be lost, or image quality may be
affected.
46
Signal format
480i(525i)@60Hz
480p(525p)@60Hz
576i(625i)@50Hz
576p(625p)@50Hz
720p(750p)@60Hz
fh(kHz)
15.73
31.47
15.63
31.25
45.00
fv(Hz)
59.94
59.94
50.00
50.00
60.00
720p(750p)@50Hz
1080i(1125i)@60Hz
1080i(1125i)@50Hz
1035i(1125i)@60Hz
1152i(1250i)@50Hz
37.50
33.75
28.13
33.75
31.25
50.00
60.00
50.00
60.00
50.00
■ List of supported signals (Video, S-Video signals)
Video mode
fh(kHz)
fv(Hz)
fsc(MHz)
NTSC
PAL
SECAM
PAL-M
PAL-N
PAL-60
NTSC4.43
15.73
15.63
15.63
15.73
15.63
15.73
15.73
60
50
50
60
50
60
60
3.58
4.43
4.25 or 4.41
3.58
3.58
4.43
4.43
■ Pin assignment of COMPUTER & MONITOR terminals
11
6
1
15
10
Pin
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
5
Mini D sub 15 Pin connector
Input Signal
• RGB input
R/G/B signals:
0.7V (p-p) 75 Ω
Horizontal sync signal: TTL level (Pos/neg polarity)
Vertical sync signal: TTL level (Pos/neg polarity)
• Y/PB/PR input
Y signal:
PB/PR signals:
1.0V (p-p) 75 Ω
0.7V (p-p) 75 Ω
Pin description
During RGB input
During Y/PB/PR input
Video signal (R)
Color difference signal (PR)
Video signal (G)
Luminance signal (Y)
Video signal (B)
Color difference signal (PB)
GND
∗
GND
∗
GND (R)
GND (PR)
GND (G)
GND (Y)
GND (B)
GND (PB)
N.C
∗
GND
∗
GND
∗
N.C
∗
Horizontal sync signal
∗
Vertical sync signal
∗
N.C
∗
∗ Do not connect anything.
47
Others
■ List of supported signals (RGB signals)
Specifications (Continued)
■ CONTROL terminal
● Pin assignment
7
6
8
5
3
4
2
1
Pin No.
1
2
3
4
5
6
7
8
Signal Name
RXD
CTS
DSR
GND
RTS
N.C
TXD
N.C
Description
Receiving data
Consent to send
Data set ready
Signal ground
Request to send
No connection
Sending data
No connection
Mini DIN 8 pin connector
● Interface format
1 Communication method
2 Communication format
3 Data format
4 Replies
RS-232C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length:
1 bit
STX (02h) Command (3Byte) ETX (03h)
Only 1 command valid per communication.
For input commands, only ASCII-compliant all-uppercase
alphanumeric characters supported.
Acknowledge
No acknowledge
ACK (06h) CR (0Dh) Data
... Normally ended
ACK (06h) ESC (1Bh)
... Aborted
NAK (15h)
If commands are to be sent consecutively, wait for the response from the projector
before sending the next command.
● Main Commands
Item
Power on
Power off
Icon display on
Icon display off
Auto setting (RGB input)
Status display on
Status display off
Command
PON
POF
MO0
MO1
PAT
DON
DOF
Item
Computer input select
Y/PB/PR input select
Video input select
S-video input select
Camera input select
Command
IN1
IN2
IN3
IN4
IN5
Note
• Contact your dealer for control cable and other commands.
■ Separately Sold Product
Replacement Lamp
Model TLPLV2
Note
• Design, specifications, etc. subject to change without notice for improvements, etc.
48