DeLorme 6 GPS Receiver User Manual

3LCD DATA PROJECTOR
TLP-T50M
TLP-T50
TLP-S30
(XGA / with a mouse remote control)
Before Using
OWNER’S MANUAL
Others
TLP-T50M / TLP-T50 / TLP-S30
Maintenance
Operations
(SVGA)
Preparations
(XGA)
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES
ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
FCC Radio Frequency Interference Statement
Note:
This equipment has been tested and found to comply with the limits for a Class
USA only A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiates radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
WARNING: Changes or modifications made to this equipment, not expressly approved by
USA only Toshiba, or parties authorized by Toshiba, could void the user’s authority to operate
the equipment.
Notice:
This Class A digital apparatus complies with Canadian ICES-003. Cet appareil
CANADA only numérique de la classe A est conforme à la norme NMB-003 du Canada.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND
INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE
MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE
REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can
result in electric shock or fire hazard. The safeguards incorporated in this unit will protect you
if you observe the following procedures for installation, use and servicing. This unit is fully
transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO
DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL ONLY.
1. Read Owner's Manual
3. Source of Light
After unpacking this product, read
the owner's manual carefully, and
follow all the operating and other
instructions.
Do not look into the lens while the
lamp is on. The strong light from
the lamp may cause damage to
your eyes or sight.
4. Ventilation
Openings in the cabinet are
provided for ventilation and to
ensure reliable operation of the
product and to protect it from
overheating, and these openings
must not be blocked or covered.
The openings should never be
blocked by placing the product on
a bed, sofa, rug or other similar
surface. This product should not
be placed in a built-in installation
such as a bookcase or rack unless
proper ventilation is provided or
the manufacturer's instructions
have been adhered to.
2. Power Sources
This product should be operated
only from the type of power source
indicated on the marking label.
If you are not sure of the type of
power supply to your home,
consult your product dealer or
local power company.
For products intended to operate
from battery power, or other
sources, refer to the operating
instructions.
WARNING: This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
2
3
Before Using
SAFETY PRECAUTIONS
5. Heat
8. Power-Cord Protection
The product should be situated
away from heat sources such as
radiators, heat registers, stoves, or
other products (including
amplifiers) that produce heat.
Power-supply cords should be
routed so that they are not likely to
be walked on or pinched by items
placed upon or against them,
paying particular attention to cords
at plugs, convenience receptacles,
and the point where they exit from
the product.
6. Water and Moisture
11. Object and Liquid Entry
14. Attachments
Never push objects of any kind
into this product through openings
as they may touch dangerous
voltage points or short-out parts
that could result in a fire or electric
shock. Never spill liquid of any
kind on the product.
Do not use attachments not
recommended by the product
manufacturer as they may cause
hazards.
15. Accessories
Do not place this product on an
unstable cart, stand, tripod,
bracket, or table. The product may
fall, causing serious injury to a
child or adult, and serious damage
to the product. Use only with a
cart, stand, tripod, bracket, or table
recommended by the
manufacturer, or sold with the
product. Any mounting of the
product should follow the
manufacturer's instructions, and
should use a mounting accessory
recommended by the
manufacturer. A product and cart
combination should be moved with
care. Quick stops, excessive
force, and uneven surfaces may
cause the product and cart
combination to overturn.
12. Do not place the product
vertically
Do not use this product near water.
- for example, near a bath tub,
wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a
swimming pool and the like.
9. Overloading
Do not overload wall outlets;
extension cords, or integral
convenience receptacles as this
can result in a risk of fire or
electric shock.
Do not use the product in the
upright position to project the
pictures at the ceiling, or any other
vertical positions. It may fall down
and dangerous.
7. Cleaning
Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
Use a soft cloth for cleaning.
10. Lightning storms
For added protection for this
product during storm, or when it is
left unattended and unused for
long periods of time, unplug it from
the wall outlet. This will prevent
damage to the product due to
lightning and power-line surges.
4
13. Stack Inhibited
Do not stack other equipment on
this product or do not place this
product on the other equipment.
Top and bottom plates of this
product develops heat and may
give some undesirable damage to
other unit.
S3125A
5
Before Using
IMPORTANT SAFETY INSTRUCTIONS (Continued)
IMPORTANT SAFETY INSTRUCTIONS (Continued)
18. Servicing
Unplug this product from the wall
outlet and refer servicing to
qualified service personnel under
the following conditions:
a) When the power-supply cord or
plug is damaged.
b) If liquid has been spilled, or
objects have fallen into the
product.
c) If the product has been exposed to
rain or water.
d) If the product does not operate
normally by following the operating
instructions. Adjust only those
controls that are covered by the
operating instructions as an
improper adjustment of other
controls may result in damage and
will often require extensive work by
a qualified technician to restore
the product to its normal
operation.
e) If the product has been dropped or
damaged in any way.
f) When the product exhibits a
distinct change in performance this indicates a need for service.
Do not attempt to service this
product yourself as opening or
removing covers may expose you
to dangerous voltage or other
hazards. Refer all servicing to
qualified service personnel.
21. Do not leave thermal-paper
documents or easily
deformed items on top of
the unit or near the air
exhaust.
Before Using
16. Damage Requiring Service
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
Also, when you touch a metal
object put near the air exhaust, a
burn may be caused.
19. Replacement Parts
When replacement parts are
required, be sure the service
technician has used replacement
parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
(Replacement of the lamp only
should be made by users.)
17. If glass components,
including lens and lamp,
should break, contact your
dealer for repair service.
20. Safety Check
Upon completion of any service or
repairs to this product, ask the
service technician to perform
safety checks to determine that
the product is in proper operating
condition.
This product incorporates glass
components, including a lens and
a lamp. If such parts should
break, please handle with care to
avoid injury and contact your
dealer for repair service. The
broken pieces of glass may cause
to injury. In the unlikely event of
the lamp rupturing, thoroughly
clean the area around the
projector and discard any edible
items placed in that area.
6
7
IMPORTANT PRECAUTIONS (Continued)
Avoid Volatile Liquid
If your line voltage is 220 to 240V, use one of the following types of cable.
Plug
configuration Plug type
EURO
UK
Plug
configuration
Line voltage
220 – 240V
220 – 240V
Use a 5A fuse which is approved by ASTA
or BSI to BSI362.
Always replace the fuse cover after
changing the fuse.
Plug type
Line voltage
Australian
240V
10A
200 – 240V
Switzerland
240V
6A
200 – 240V
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time. They will leave marks on the finish.
If cleaning with a chemically saturated cloth, be sure to follow the product's precautions.
LCD Panel
North American 200 – 240V
240V
15A
IMPORTANT PRECAUTIONS
The life of the LCD panel is limited. Take care over the points below so as to use the panel
for years.
• To prolong the life of this panel, never fail to turn the power off when the panel is not in use
and make sure that the lamp has gone out. The state of the lamp being extinguished helps
enhance the effect of energy saving.
• If the air filter is stained and is clogged up, the main unit inner temperature rises. As a
result, the life of the LCD is shortened and a malfunction may also occur.
Clean the air filter from time to time and replace it regularly. It is recommended that this
replacement be done at the time of replacing a lamp. (Ask a dealer where the unit was
purchased or your nearby service station about an air filter for replacement.)
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to
ship your LCD projector. For maximum protection, repack the set as it was originally packed
at the factory.
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on the
crucial internal parts. To prevent the unit from possible damage, do not use the unit for at
least 2 hours when there is an extreme or sudden change in temperature.
In the spaces provided below, record the Model and Serial No. located at the bottom of your
LCD projector.
Model No.
Serial No.
Retain this information for future reference.
Place and Manner of Installation
• Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the LCD panel.
• Avoid locations with oil or cigarette smoke. Doing so will dirty the LCD panel and other
optical parts, shortening their lives, and darkening the screen.
• Do not use in angle of 20° or more degrees. Doing so could shorten the life of the lamp.
• If used at high altitudes, the unit could cease operation even if used within the rated
temperature range. This is because the thinner air at high altitudes decreases the internal
cooling efficiency. Therefore, please lower the ambient temperature if using at high altitudes.
8
9
Before Using
POWER SUPPLY CORD SELECTION
CONTENTS
• Toshiba Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, operating
by third parties, other accidents, or use under abnormal conditions including erroneous or
improper operation and other problems.
• Toshiba Corporation bears no responsibility for incidental damages (lost profit, work
interruption, corruption or loss of the memory contents, etc.) arising from the use of or the
inability to use this unit.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from not having
followed the descriptions in this Instruction Manual.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from
malfunctions arising from combination with equipment or software that is not related to
Toshiba Corporation.
Before Using
OTHER CAUTIONS AND INFORMATIONS
Copyrights
Publicly showing or transmitting commercial imaging software or broadcast or Cable-broad
casting programs, either commercially or collecting a fee from the audience, or modifying
images using the freeze or resize functions, could violate the direct or indirect copyrights of
the imaging software or broadcast program, etc., if done without first consulting with the
copyright holder. For this reason, please take appropriate measures before performing one
of the actions listed above, including obtaining a license from the copyright holder.
Disposal
This product contains substances which are harmful to humans and the environment.
• The solder used in the PCB manufacturing process contains lead.
• The lamp contains inorganic mercury.
Please dispose of this product or used lamps in accordance with local regulations.
Trademarks
• VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of International
Business Machines Corporation.
• Macintosh is a registered trademark of Apple Computer, Inc.
• Windows is a registered trademark of Microsoft Corporation in the U.S. and other countries.
Notational Conventions Used in This Manual
References to pages with related information are annotated as follows.
For example, if making a reference to page 36: p.36
10
SAFETY PRECAUTIONS ..........................................................................................
IMPORTANT SAFETY INSTRUCTIONS ...................................................................
POWER SUPPLY CORD SELECTION .....................................................................
IMPORTANT PRECAUTIONS ...................................................................................
EXEMPTION CLAUSES ............................................................................................
OTHER CAUTIONS AND INFORMATIONS ..............................................................
CONTENTS ...............................................................................................................
2
3
8
8
10
10
11
Preparations
Checking the package contents .................................................................................
Names of each part on the main unit .........................................................................
Names of each part on the control panel and remote control ....................................
Names of the connection terminals ...........................................................................
Preparing and using the remote control ....................................................................
Placement ..................................................................................................................
Connection ................................................................................................................
12
13
14
15
16
17
18
Operations
Turning the power on and off .....................................................................................
Basic operations ........................................................................................................
Using handy features .................................................................................................
Using auto setting (Auto setting) ............................................................................
Correcting the keystone distortion (Keystone) .......................................................
Cutting off the picture and sound temporarily (Mute) .............................................
Freezing the image (Freeze) ..................................................................................
Enlarging the picture size (Resize) ........................................................................
Displaying Information [Status display] ..................................................................
Using the menus ........................................................................................................
How to use the menus ...........................................................................................
The image adjustment menu ..................................................................................
The default setting menu ........................................................................................
The display setting menu .......................................................................................
Reset menu (Special menu) ...................................................................................
19
21
23
23
24
24
25
25
26
27
27
28
28
29
29
Maintenance
Air filter cleaning ........................................................................................................ 30
Lens and main unit cleaning ...................................................................................... 31
Lamp replacement ..................................................................................................... 31
Others
Trouble indications .....................................................................................................
Before calling service personnel ................................................................................
Specifications ............................................................................................................
List of general specifications ..................................................................................
List of supported signals (RGB signals) .................................................................
List of supported signals (Y/PB/PR signals) ..........................................................
List of supported signals (Video, S-Video signals) .................................................
Pin assignment of COMPUTER & MONITOR terminals ........................................
CONTROL terminal ................................................................................................
Separately Sold Product ........................................................................................
11
33
34
35
35
36
37
37
37
38
38
Before Using
EXEMPTION CLAUSES
Checking the package contents
Names of each part on the main unit
Please make sure that the following items are included in the box, along with the main unit.
If an item is missing, please contact the store from which you purchased the product
immediately.
(1)
(6)
(2)
(7)
(3)
(8)
(4)
(9)
WARNING Label
(4)
(3) (2) (1)
(5)
(11)
(6)
(4)
(7)
(8) (9)
(10)
(5)
(7)
CAUTION Label
MODEL NO./
RATING Label
CAUTION Label
VOL.
MOD
E
PJ
(5)
STO
P
-
MEN
(9)
INPU
T
U/EN
TER
R-CL
ICK
PLAY
LASE
R
(12)
(8)
(15)
(16)
(12)
(10)
SERIAL NO. Label
■ (1) Remote control
■ (2) R03 (SIZE AAA) batteries for remote
control (2)
■ (3) Quick Reference
■ (4) CD-ROM
■ (5) Owner’s Manual
■ (6) Power cord (See note)
■ (7) RGB cable
■
■
■
■
■
(8) Video cable
(9) Audio cable (for computer)
(10) Audio cable
(11) Carrying bag
(12) Mouse remote control set (*)
• Mouse remote control, batteries
• Mouse remote control receiver
• Mouse remote control manual
(*) Supplied with TLP-T50M
Note
The shape and number of power cords supplied vary depending on the product destination.
◆The Supplied CD-ROM
The supplied CD-ROM contains an owner’s manual including information omitted in the
Owner’s manual (Getting started), Acrobat® Reader™, which is needed to view the manual.
■ Installing Acrobat® Reader™
Windows: In the CD-ROM, select the Reader/English folder, and run ar500enu.exe.
Follow the on-screen instructions.
Macintosh: In the CD-ROM, select the Reader/English folder, and run Reader Installer.
Follow the on-screen instructions to install the software.
■ Viewing the manual
In the CD-ROM, double-click on Start.pdf. Acrobat® Reader™ launches, and the menu
screen of the Owner’s manual appears. Click on your language. The Owner’s Manual
cover and list of bookmarks appear. Click on a bookmark title to view that section of the
to view a reference page with related information. See the Help
manual. Click on p.
menu for more information about Acrobat® Reader™.
12
(11) (12)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(14) (13)
Name
Lens
Zooming lever
Focusing ring
Infrared remote sensor
Control panel
AC IN socket
Air intake
Foot adjuster
Foot adjuster release button
Connection terminal
Anti-theft lock hole
Tilt adjuster
Speaker
Air exhaust
Lamp cover
Air filter catch
(14)
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Function
Projects expanded image
Adjusts screen size p.22
Adjusts screen focus p.22
Senses commands from the remote control p.16
Operates the projector p.14
Connect the supplied power cord here p.19
Draws in air from outside unit
Adjusts the vertical projection angle p.22
Press to stow the foot adjuster p.22
Connect to an external device p.18
Attach a security chain, etc. here
Adjusts the projector’s horizontal tilt p.22
Plays audio
Expels air that has grown hot inside the projector
Remove to replace lamp p.32
Take this to pull out the filter for cleaning p.30
13
Preparations
WARNING Label
Names of each part on the control panel and remote control
Control panel
Remote Control
CLASS 1 LED PRODUCT
(15)
CONTROL
AUDIO
(3)
VIDEO
VIDEO
S-VIDEO
(2)
(1)
COMPUTER
( Y/PB/PR )
MONITOR
(1)
AUTO
SET
(4)
MUTE
FREEZE
(12)
(11)
ON
(5) (4)
ON/
STANDBY
CALL
KEYSTONE
FAN TEMP LAMP
(6)
Remote control transmitter
(3)
(7) (8) (9) (10)
Names of the connection terminals
INPUT
(13)
ON / STANDBY
(2)
(1)
RESIZE
OFF
(14)
INPUT
MENU
VOL. -
(2)
(6)
VOL. +
AUTO
KEYSTONE
(3)
VOL.-
(5)
MENU
AUTO SET
VOL.+
(5)
(6)
(4)
(1) COMPUTER terminal
Input RGB signal from a computer or other source, or a component video signal (Y/PB/
PR) from video equipment.
(2) MONITOR terminal
Connect to a computer display, etc.
CT-90140
(3) S-VIDEO terminal
Input S video signals from video equipment.
(4) VIDEO terminal
Input video signals from video equipment.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
Name
ON/STANDBY button
INPUT button
AUTO KEYSTONE button
AUTO SET button
MENU button
Selection button
FAN indicator
TEMP indicator
LAMP indicator
ON indicator
MUTE button
FREEZE button
RESIZE button
OFF button
CALL button
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Main Function
Turns the power on/off (standby) p.19
Selects input p.21
Adjusts keystone (trapezoidal distortion) p.24
Sets up image and mode p.23
Displays menus and makes selections p.27
Menu selections and adjustments, etc. p.27
Displays cooling fan mode p.20 p.33
Lights when internal temperature too high p.33
Displays lamp mode p.20
Displays whether power is on or off p.19
Cuts off the picture and sound temporarily p.24
Pauses image p.25
Enlarges picture size p.25
Turns off enlarged picture display p.25
Displays the information on the screen p.26
(5) AUDIO terminal
Input audio signals from a computer or video equipment.
(6) CONTROL terminal
When operating the projector via a computer, connect this to the controlling computer’s
RS-232C port. p.38
Note
• Although this owner’s manual abbreviates component video signals as Y/PB/PR, the
product also supports signals from video equipment marked “Y/CB/CR.”
Notes
• For the remainder of this manual, buttons are referred to as follows:
; MENU button ⇒
Selection button ⇒
• For further information of the mouse remote control supplied with the TLP-T50M, see the
Owner’s Manual of the Mouse Remote Control.
14
15
Preparations
RESIZE
Preparing and using the remote control
Placement
■ Loading dry-cell batteries
into the remote control
■ Operating the remote control
Placement Styles
Point the remote control toward the
projector’s infrared remote sensor,
and press a button on the remote
control.
As shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the placement style in the
default setting menu p.28 , in accordance with your needs.
q Remove the battery cover.
Floor-mounted front projection
Floor-mounted rear projection
• Operating the projector from the front
w Insert the dry-cell batteries.
Be sure to align the plus and minus
ends of the batteries properly.
Approx. 15°
Ceiling-mounted front projection
Ceiling-mounted rear projection
Ap
pro
x. 5
m
AC IN
• Operating the projector from the rear
CAUTION
• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when
placing the unit.
• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so.
Mounting the projector on a ceiling requires special ceiling brackets (sold separately)
and specialized knowledge. Improper mounting could cause the projector to fall,
resulting in an accident.
Two batteries (LR03 or R03, SIZE
AAA) are used.
e Replace the battery cover.
Approx. 15°
Ap
pro
x. 5
m
Projection Distance and Screen Size
Use the figures, table, and formula below to determine the screen size and projection
distance. (Screen sizes are approximate values for full-size picture and no keystone
adjustment)
projection size (inches) – 1.082
a (min length) =
Screen As seen from above
26.107
Dry-cell batteries
• Remove batteries from remote control when not using for extended periods.
• If the remote control stops working, or if its range decreases, replace all the batteries
with new ones.
a (max length) =
90°
The remote control
screen
size (cm)
As seen from the side
• The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
• Do not drop or bang.
• Do not leave in hot or humid locations.
• Do not get wet or place on top of wet objects.
• Do not take apart.
• In rare cases, ambient conditions could impede the operation of the remote control. If
this happens, point the remote control at the main unit again, and repeat the operation.
16
32 (81)
40 (102)
60 (152)
80 (203)
100 (254)
150 (381)
200 (508)
250 (635)
300 (762)
Lens center
90°
a
a is the distance (m) between the lens and
the screen, and corresponds to a range of
1.41 m to 11.45 m.
17
projection size (inches) – 0.906
21.854
projection distance a(m)
min length
max length
(zooming max) (zooming min)
—
1.41
1.49
1.79
2.26
2.70
3.02
3.62
3.79
4.53
5.70
6.82
7.62
9.11
9.53
11.40
11.45
—
Preparations
AC IN
Connection
Turning the power on and off
Before connection
Connecting the power cord
• Read the owner’s manual of the device to be connected to the projector.
• Some types of computer cannot be used connected to this projector.
Check for an RGB output terminal, supported signal p.36 , etc.
• Turn off the power of both devices before connection.
• The figure below is a sample connection. This does not mean that all of these devices
can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)
Computer
CRT monitor, etc.
1
2
Insert the power cord connector into the AC IN socket of the projector.
Insert the power cord plug into a wall or other power outlet.
(Supplied) Power cord connector
When the power cord is plugged in, the following three
green indicators will come on for several seconds: ON,
TEMP, and LAMP. Next, the ON indicator will change to
orange, indicating standby mode.
(Do not perform any operations while the 3 green
indicators are lit.)
Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat.
To audio output
To RGB
output
Audio cable
(for computer)
(supplied)
AUDIO
VIDEO
VIDEO
S-VIDEO
MONITOR
■ Turning the power on
COMPUTER
( Y/PB/PR )
Press the ON/STANDBY
button.
Monitor cable
Mini D-sub 15P-BNC
(not supplied)
The power turns on, and the
following 3 green indicators light:
ON, LAMP, and FAN. After a
moment, the start-up screen
appears.
p.38
Yellow
(to video output)
Video cable
(supplied)
To audio
To RS-232C terminal output
White (L)
Red (R)
Computer (for control)
To Y/CB/CR
output
Green (Y)
Blue (CB),
Red (CR)
S-Video cable
(not supplied)
To audio
output
To S-Video White (L)
output
Red (R)
VCR
FAN TEMP LAMP
Remote
Control
ON
Conversion adapter
BNC-pin
(not supplied)
INPUT
ON / STANDBY
KEYSTONE
Start-up screen
ON/
STANDBY
CALL
Audio cable
(supplied)
Control cable
Control panel
AUTO
MUTE
SET
FREEZE
MENU
RESIZE
VOL. -
VOL. +
AUTO
KEYSTONE
RESIZE
OFF
AUTO SET
INPUT
CAUTION
• Do not look into the lens during operation. Doing so could damage your vision.
• Do not block the air intake or exhaust. Doing so could cause a fire due to internal
overheating.
• Do not place your hands, face, or other objects near the air exhaust. Doing so could
cause burns, deform/break the object.
DVD player
Notes
Note
• The AUDIO terminal is common among all the devices for input terminal.
18
• The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the start-up screen not to
appear via the Display setting menu p.29 .
• The first time you use the projector after purchase, after the start-up screen disappears,
the Language menu is displayed p.21 .
19
Operations
CONTROL
RGB cable
(supplied)
Turning the power on and off (Continued)
Basic operations
Turning the power off
1 Turn on the power.
Turn on the power, following the instructions in “Turning on the power” p.19 .
Press the ON/STANDBY button.
A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button again.
The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
When cooling lamp
FAN
TEMP LAMP
(Green)
(Green) (Orange)
Flashing
A
A
ON
During internal cooling
FAN
(Green)
TEMP LAMP
(Off)
B
After cooling complete
ON
FAN
(Orange)
(Off)
TEMP LAMP
(Off)
ON
(Orange)
2 Select language (When using for first time).
When the projector is used for the first time after purchase, a message is displayed on
the screen, and the language menu appears. The default language is English.
(If the screen focus is not on the menu, adjust according to step 6 .)
q Use the
buttons to select the desired
language, and press the
button.
A message displays the selected language.
w Press the
button to apply.
C
During cooling, the LAMP indicator flashes. In this state, the power cannot be
turned back on. In addition, unplugging the power cord in this state will shorten
the life of the lamp.
B
After the LAMP indicator goes off, the cooling fan continues to operate for a
short while, in order to expel excess internal heat. If you are in a hurry, there is
no problem with unplugging the power cord in this state.
C
In standby
English ................ English
Français .............. French
Deutsch .............. German
Italiano ................ Italian
Español ............... Spanish
Português .......... Portuguese
................... Japanese
....... Chinese (simplified)
....... Chinese (traditional)
................... Korean
Notes
• After the first time the projector is turned on, the Language menu does not appear
upon startup. However, from the Reset menu p.29 select “Reset all” to display the
Language menu the next time the projector is turned on.
• The language can also be set via the Display setting menu p.29 .
• This owner’s manual assumes that English has been selected.
3 Place connected device(s) in operating status.
Note
• The projector consumes about 6W of power in standby. We recommend that you unplug
the power cord if you will not be using the projector for an extended period.
Turn on and boot up connected computers and other devices.
4 Select input.
PRECAUTIONS
• Before unplugging the power cord, make sure that the LAMP indicator is off. Unplugging
the power cord and cutting off the power while the projector is running or being cooled
will shorten the life of the lamp. However, please unplug the power cord if the
projector locks up or acts abnormally.
• If the power cord was unplugged before cooling was complete, give the lamp sufficient
time to cool before plugging it back in. If the lamp overheats it may fail to light, and its
lifetime will be shortened.
q Press the INPUT button.
A list of inputs appears on the screen.
w Use the
buttons to select the desired
input, and press the
button.
The picture for the selected input is projected.
LCD Panels
LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the
following precautions.
• In order to extend the lifetime of the LCD panel, always turn off the power when not in
use, and make sure that the lamp is off. Keeping the lamp off is also very effective at
saving electricity.
• If the air filter becomes dirty and clogged, the projector’s internal temperature will rise,
shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter
from time to time p.30 , and replace it periodically. Contact the store where you
purchased your projector, or your local Service Station for replacement air filters.
20
21
Computer
Y/PB/PR
Video
S-video
Operations
1
Basic operations (Continued)
Using handy features
5 Projector placement angle adjustments
■ Using auto setting (Auto setting)
The placement angle and the height of the projected image can be adjusted by the foot
adjuster.
This function sets up the projector to the optimum state for
each type of the input signal by using simple operations. Control panel
q Lift up the front of the projector until
it is at the desired angle, then press
the foot adjuster release button.
1 Press the AUTO SET button.
1
ON / STANDBY
KEYSTONE
ON/
STANDBY
AUTO
SET
The Auto setting menu appears.
MUTE
2 Press the AUTO SET button again.
2
3
To stow the foot adjuster, hold up the projector while pressing the foot adjuster
release button, then slowly lower the projector will the button depressed.
6 Adjusting the picture size and focus
RESIZE
VOL. -
VOL. +
AUTO
KEYSTONE
RESIZE
OFF
AUTO SET
INPUT
Note
• Auto adjustment/setting may not be performed correctly for input signals other than
those supported by the projector p.36 , p.37 .
● Manual adjustment and setting
The menu items vary according to the input type, as shown in the table below.
buttons to adjust the items in the table below, then press
Use the
button when you are finished. The menu disappears.
the
1
buttons
Input
Computer
The speaker volume can be adjusted when an audio signal is being input.
Notes
Y/PB/PR
Select Item
• Note that the lamp characteristics may rarely cause the brightness to fluctuate slightly.
• A lamp is consumable supplies.
If used for extended periods, images will appear dark, and the lamp could burn out. This
is characteristic of a lamp, and is not malfunction. (The lifetime of the lamp depends on
conditions of use.)
• The LCD panel is made using extremely advanced technology, but there may be black
spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.
Please note that these are not malfunctions.
• Although this projector supports a wide range of RGB signals p.36 , any resolutions not
supported by the model (XGA or SVGA, depending on the model) will be expanded or
shrunk, which will affect image quality slightly. To view high-quality images, it is
recommended that the computer’s external output should be set to the projector’s
resolution.
• With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the owner’s manual of your computer.
icon will appear.
• If a signal not supported by the projector is input, the
icon will appear.
• If a no signal is being input from the connected device, the
icon will appear.
• If an unavailable operation button is pressed, the
Item
Video
S-video
Description
Phase
Adjust with
to eliminate flicker.
Frequency
Adjust with
to eliminate periodic patterns and
flickering when many vertical lines appear in the screen.
H-position
Move left
Move right
V-position
Move up
Move down
Phase
Adjust with
to eliminate flicker.
Signal format [ : Enter to setting mode] [
: Select one
of the following] [Apply: ]
480i(525i)@60Hz/480p(525p)@60Hz/
576i(625i)@50Hz/576p(625p)@50Hz/
720p(750p)@60Hz/720p(750p)@50Hz/
1080i(1125i)@60Hz/1080i(1125i)@50Hz/
1035i(1125i)@60Hz/1152i(1250i)@50Hz
Video mode
[ : Enter to setting mode] [
: Select one
of the following] [Apply: ]
NTSC/PAL/SECAM/PAL-N/PAL-M/PAL60/NTSC4.43
23
Operations
2
Select Item
q Use the zooming lever to adjust the screen
size.
w Use the focusing ring to adjust the focus.
FREEZE
MENU
The menu item is automatically adjusted/set.
icon will appear during
For computer input, the
processing.
w Turn the foot adjuster to fine-tune
the angle.
e To adjust the horizontal angle, use
the tilt adjuster.
22
ON
CALL
INPUT
The foot adjuster extends. Release the
button to lock the position.
7 Adjusting the volume with the
FAN TEMP LAMP
Remote
Control
Using handy features (Continued)
■ Correcting the keystone distortion (Keystone)
When the foot adjuster p.22 is used to change the
projection angle, the picture will undergo keystone (trapezoidal) distortion.
This projector is capable of correcting this keystone
distortion.
Before correction After correction
■ Freezing the image (Freeze)
Control panel
FAN TEMP LAMP
Remote
Control
ON
ON/
STANDBY
CALL
INPUT
ON / STANDBY
KEYSTONE
AUTO
FREEZE
MENU
Press the remote control’s FREEZE button.
AUTO
SET
The picture is paused. The Freeze function is released when
pressing the FREEZE button again.
FREEZE
RESIZE
RESIZE
OFF
VOL. +
AUTO
KEYSTONE
Notes
RESIZE
OFF
AUTO SET
INPUT
q Press the AUTO KEYSTONE button.
The Keystone menu appears.
INPUT
• The
icon will appear while freeze is in effect.
• The freeze function can be used on the resize function. Other
operations will release the freeze.
• Even if an image is frozen on the projector, it is still changing on the video or other
equipment.
■ Enlarging the picture size (Resize)
The keystone distortion is automatically corrected. The
processing.
icon will appear during
The image being projected can be enlarged.
1 Press the remote control’s RESIZE
button.
The enlargement ratio is increased each time the RESIZE
● Manual adjustment
button is pressed.
buttons for keystone adjustment. When the adjustment is finished,
button. The menu disappears.
Item
Keystone
2 To decrease the enlargement ratio, press the remote control’s
Description
Shrink screen bottom
RESIZE
Shrink screen top
button.
The enlargement ratio is decreased each time the RESIZE
(The image cannot be shrunk to less than its original size.)
Notes
• Depending on the amount of keystone adjustment and the contents of images,
some information may be lost, or the picture quality may suffer.
• Keystone adjustment will not change the shape of the menus.
button is pressed.
RESIZE
3 Press and hold down the
buttons to
move the enlarged area.
■ Cutting off the picture and sound temporarily (Mute)
When you want to temporarily project the images of another projector,
overhead projector, etc., this projector’s images and sound can be turned
off.
ON/
STANDBY
CALL
AUTO
MUTE
MENU
VOL.+
3
4 Press the RESIZE OFF button to undo the resize.
FREEZE
Notes
RESIZE
INPUT
24
INPUT
The resize is released, and the image returns to its original size.
SET
RESIZE
OFF
• The
icon will appear while mute is in effect.
• Operating any other function exits the muting.
1
RESIZE
OFF
Remote
Control
The picture and sound are cut off. The Mute function is released
when pressing the MUTE button again.
Notes
2
4
VOL.-
KEYSTONE
Press the remote control’s MUTE button.
Remote
Control
• The
icon will appear while resize is in effect.
• An enlarged image can be frozen using the FREEZE button. The resize function on
a frozen image can also be used.
• Operations other than freeze will release the resize.
• Since the enlargement is performed using digital processing, enlarging the image
will cause it to appear jagged.
• Rarely, the picture could become garbled while the enlarged area is being moved.
25
Operations
w Press the AUTO KEYSTONE button again.
Use the
press the
KEYSTONE
RESIZE
VOL. -
ON/
STANDBY
CALL
MUTE
SET
MUTE
Remote
Control
The image being projected can be made to be frozen. This function is to
be used to pause a video during a presentation, etc.
Using handy features (Continued)
Using the menus
■ Displaying Information [Status display]
You can call up on-screen menus, and conduct a number of adjustments and settings,
using the operation buttons p.14 on the control panel (main unit side) and remote control.
Press the
button twice (or press the CALL button on the remote
control once).
Remote
When the
button is pressed once, the Setting
display menu appears. Pressing it again displays
information p.27 . The table below shows what kind
of information is displayed. Press the button (or the
CALL button on the remote control) again to
dismiss the display.
Control panel
FAN TEMP LAMP
Control
ON
ON / STANDBY
KEYSTONE
The menu shown below is only for operation instructions and might be different from the
actual display.
ON/
STANDBY
CALL
INPUT
■ How to use the menus
AUTO
MUTE
1. Start
SET
Display the Setting display menu
2. Select a Category
FREEZE
MENU
Displays the
current adjustment/setting of
each category
RESIZE
VOL. -
VOL. +
AUTO
KEYSTONE
To Image adjustment menu
RESIZE
OFF
p.28
AUTO SET
INPUT
To Display setting menu
“Yes”: displayed, “No”: not displayed
Item
Description
Computer Y/PB/PR
Input
Input source name
Yes
Yes
RGB signal mode RGB input mode [Note 1]
Yes
No
H-resolution
Horizontal resolution (in bits) Yes
No
V-resolution
Vertical resolution (in bits)
Yes
No
H-frequency
Horizontal sync frequency
Yes
No
V-frequency
Vertical sync frequency [Note 2] Yes
No
Sync
Sync signal polarity [Note 3]
Yes
No
Signal format
Y/PB/PR signal format
No
Yes
Video mode
Color method of video signal
No
No
Lamp time
Time of lamp use [Note 4]
Yes
Yes
Yes
Yes
Version
Firmware version [Note 5]
Video
Yes
No
No
No
No
No
No
No
Yes
Yes
Yes
p.29
S-video
Yes
No
No
No
No
No
No
No
Yes
Yes
Yes
Notes
1: The mode of supported RGB signals p.36 is shown.
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the time displayed approaches 2,000
hours, consult with a store about getting a TLPLV1 replacement lamp (sold separately)
prepared.
5: [Version] shows the version of the projector’s internal control program. This version is
referred to for customer service, etc.
Notes
To Default setting menu
p.28
3. Adjustments & Settings
5. To Finish
Item
Adjustment/Setting Value
These marks signify the
items can be adjusted/set
by using
.
These marks signify an
item can be switched by
using
.
Finish via the Status
display menu.
This mark signfy that
there are options.
Press
to display a
list of options.
To Status display
p.26
The figure shows a typical example.
As the display may differ depending
on the item, use the following pages
as a reference.
These marks signify the items can be selected from
the list by using
.
After an item selected, apply it by pressing
.
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
• Conducting another operation while information is being displayed dismisses the
display.
6. End
The menu disappears
4. Back
Note
• Menu adjustments and settings (except Lamp power p.28 ) are saved when the power is
turned off via the ON/STANDBY button. If the power cord is unplugged before this, or the
power goes out, then the data will not be saved.
26
27
Operations
This displays information about the input signal, lamp use time, etc.
Using the menu (Continued)
■ The image adjustment menu
■ The display setting menu
Use this menu to adjust image-related items.
Items Items that can be adjusted are marked with “Yes”, and those that cannot are marked
with “No”.
Use this menu to set screen display-related items.
Item
Description
Screen size
Item
Description
Computer Y/PB/PR
Video
S-video
Contrast
Lower
Higher
Yes
Yes
Yes
Yes
Brightness
Darker
Brighter
Yes
Yes
Yes
Yes
Color
Lighter
Deeper
No
Yes
Yes
Yes
Reddish
Greenish
No
No
Yes
Yes
Sharpness
Softer
Sharper
No
Yes
Yes
Yes
R-level
Less red
More red
Yes
Yes
Yes
Yes
G-level
Less green
More green
Yes
Yes
Yes
Yes
B-level
Less blue
More blue
Yes
Yes
Yes
Yes
Up/down shift [Note 2]
Shift down
Shift up
No
Yes
Yes
Yes
Tint
[Note 1]
(Full): Display with LCD panel’s resolution
(Thru): Display with sampling resolution (for computer input)
(Wide): Wide-screen display (for Video, S-video, and Y/PB/PR)
Language
Select one of the languages below to use for displaying menus and messages
[ : Enter setting mode] [
:Selection]
[Apply:
]
English/Français/Deutsch/Italiano/Español/
Português/
/
/
/
Background
Screen to display when there is no input signal
Icon
Display icons as function guides
On
Off
Start-up screen
Display start-up screen when power turned on
On
Off
(Logo)
(Blue)
(None)
• If “Thru” is selected for screen size, portions exceeding the pixel count of the LCD panel
p.35 will not appear on the screen. Note that for RGB signals with clock speeds
SXGA3_60 p.36 or lower, all input pixel signals are sampled. (This effect is noticeable
when the screen is enlarged using the Resize function p.36 ). However, if the clock
speed is higher than this, the RGB pixel signal is thinned before sampling.
■ The default setting menu
This menu shows placement status and other settings.
Description
Item
Projection
mode
Set projection mode in accordance with Placement Style p.17
No signal
power off
Set the time to wait after signal input stops until turning off the power:
Off (not turned off)
1 min
2 min
...
60 min
Power on
Set whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto). Manual
Auto
(Placed
on floor)
(Rear)
Lamp power [Note 1] Set the lamp power
(Hung from
ceiling)
Standard
(Back hung
from ceiling)
■ Reset menu (Special menu)
This menu is displayed when other menus are not displayed, and the
button is held
down until the menu appears.
• When the screen is placed vertically, and Auto keystone correction is executed, but
the keystone correction is not successful, stow the foot adjuster in its original position,
place the projector on a flat surface, select Horizontal reference value reset, and press
the
button.
• Select Reset All and press the
button to return all menu items to the factory settings.
Low
Item
Note
1: When lamp power is set to low, the screen becomes a little darker, but the cooling fan noise gets
quieter. This setting will be cleared when you turn the power off. The setting will be back to
“Standard” when the power is turned on next time.
Notes
Description
Horizontal reference Reset the horizontal reference value for Auto keystone correction
[ : Enter execution mode] [Yes
No] [Apply: ]
value reset
Reset all
Reset all menu items to their factory settings
[ : Enter execution mode] [Yes
No]
• Note that if Power on is set to Auto, then if the power cord is plugged in when power is
restored after a power outage, the projector power will come on.
• Even if Power on is set to Auto, press the ON/STANDBY button to turn off the power.
Unplugging the power cord to cut off the power will shorten the life of the lamp.
28
29
[Apply:
]
Operations
Note
Notes
1: Tint can only be adjusted when Video mode p.23 is NTSC or NTSC4.43.
2: Up/down shift can only be adjusted when Screen size p.29 is Wide.
Air filter cleaning
Lens and main unit cleaning
The air filter prevents dust and debris from getting inside the projector. Never run the
projector with the filter removed. It is recommended that the air filter is cleaned regularly.
(A recommended measure is about once for every 50 hours of use.)
■ Lens cleaning
CAUTION
• Request cleaning and maintenance of a ceiling-mounted unit from your projector
dealership.
1 Unplug power cord.
2 Remove the air filter.
Pull out the air filter by taking the catch shown in the figure.
• Clean the lens with a commercially available blower and/or
lens cleaner.
• The lens is easily scratched, so do not rub it with hard objects,
or strike it.
■ Main unit cleaning
• Clean the main unit after unplugging the power cord.
• Wipe dirt off the main unit gently with a soft cloth.
• If the soiling is severe, dip the cloth in a neutral
detergent diluted in water, wring well, and gently wipe
off the dirt, then finish up by wiping with a dry cloth.
● Replacing air intake and exhaust fans, and air filter
To maintain the performance, it is recommended that these should be replaced about
every 2 to 3 years. Consult with your dealer for details.
3 Clean the filter.
Carefully remove the dust and dirt from the air filter with a
vacuum cleaner or the like.
Lamp replacement
A lamp is consumable supplies. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.) If this happens, replace it with a new
one.
4 Replace the air filter.
Notes
• Allowing dirt and dust to build up on the air filter will worsen the air circulation inside the
projector, causing the internal temperature to rise, causing the projector to stop working
or malfunction.
• Insert the air filter all the way in. Leaving gaps will allow dust and dirt to get inside the
projector.
• If you wash the air filer with water, make sure to dry it completely before replacing it.
• If the air filter is torn, consult with your dealer about replacing it with a new one.
Continuing to use a ripped filter will allow dust and dirt to get inside the projector.
30
1 Unplug power cord.
2 Wait until lamp is sufficiently cooled.
Wait for at least 1 hour.
31
Maintenance
CAUTION
• Request cleaning and maintenance of a ceiling-mounted unit from your projector
dealership.
• When replacing, always use lamp “TLPLV1” (sold separately).
• If you have been using the projector, the lamp will be very hot, and may cause burn
injuries.
Wait for the lamp to cool (for longer than 1 hour) before replacing it.
• If the lamp should break, please handle with care to avoid injury due to broken pieces
and contact your dealer for repair service.
Trouble indications
Lamp replacement (Continued)
3 Remove the lamp cover.
The indicator lights inform you of internal abnormalities.
3
1
FAN
TEMP LAMP
or
4 Pull out the lamp.
FAN
TEMP LAMP
Loosen the 2 screws holding the lamp in place,
and pull on the handle to remove the lamp.
5 Mount the new lamp.
No power
⇒ Problem with projector
• Unplug the power cord, and contact your dealer.
(Off)
(Red lit)
ON
Lamp went out during use, or won’t come on
⇒ Returns to standby after about 2 minutes. If the projector fails to
operate normally after turning the power back on, either the lamp
needs replacing, or there is a problem with the projector.
• If a lamp burns out, replace it with a new one.
• Unplug the power cord, and contact your dealer.
(Red lit) (Red lit)
4
1
2
Align the orientation, press down until the bottom is
reached, and lock in place using the two lamp
locking screws.
FAN
TEMP LAMP
(Green lit) (Red lit)
6 Replace the lamp cover.
Or
Align the cover, and press it in, then screw in the
screws loosened in step 3 until the lamp cover is
no longer loose.
ON
2
(Off)
Power went out during use, or power won’t come on
⇒ Internal overheating, or the outside temperature is too high.
• Place the projector so that the air intake and exhaust are not
blocked.
• Unplug the power cord and wait for a short while, then turn the
power back on.
• Clean the air filter. p.30
Or
(Orange lit)
Or
(Green lit)
2
5
ON
(Red lit)
1
❈ The
icon will appear before the power goes out.
❈ After displaying the abnormal state for about 2 minutes, returns
to standby.
7 Reset the lamp timer.
See the lamp’s manual for instructions on resetting
the lamp timer.
FAN
TEMP LAMP
• Press the
button twice to display (a rough guide) of the time of use from the Lamp
time item on the Status display menu. p.26
• As a rule of thumb, it is recommended that the lamp should be replaced after 2,000
icon and a message will
hours of use. When Lamp time reaches 2,000 hours, the
appear. When any operation is performed, the message disappears.
• Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the
lamp may fail to come on p.33 , and the lamp’s lifetime may be shortened.
• Always replace the lamp with a new one.
• The lamp is made out of glass. Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)
Used Lamps
Power went out during use, or power won’t come on
⇒ Problem with internal cooling fan.
• Unplug the power cord, and contact your dealer.
(Red lit)
(Red lit or flashing)
Notes and Precautions
ON
Or
(Orange lit or flashing)
FAN
TEMP LAMP
icon will appear before the power goes out.
❈ The
❈ After displaying the abnormal state for about 2 minutes, returns
to standby.
ON
Power went out during use, or power won’t come on
(Orange (Red lit)
flashing)
⇒ The lamp cover is not properly attached.
• Unplug the power cord, and reattach the lamp cover. p.32
❈ The
icon will appear before the power goes out.
❈ After displaying the abnormal state for about 2 minutes, returns
to standby.
PRECAUTIONS
This projector’s lamps contain trace amounts of environmentally harmful inorganic
mercury. Be careful not to break used lamps, and dispose it in accordance with local
regulations.
• Make sure to unplug the power cord if something goes wrong.
• If the power cord is unplugged before cooling is complete, give the lamp time to cool
before plugging it back in. If the lamp overheats it may fail to light. Unplugging the power
cord repeatedly when the temperature is high will shorten the life of the lamp. (Even if
you are not concerned about lamp lifetime, the light may not come on if you do not wait
at least 3 minutes.)
32
33
Others
Loosen the 2 screws, then pull up to direction
of the arrow with your fingers on the area
shown in the figure to remove the lamp cover.
Before calling service personnel
Specifications
If you think something is wrong, check the following before contacting customer service.
Please see “Trouble indications” p.33 as well.
■ List of general specifications
Check
• Is the power cord plugged in? Is it connected to the projector?
• Is the lamp cover loose? p.33
Power goes out
during use
• Is the ambient temperature high? p.33
• Is the air filter clogged? p.33
• Is the air intake or air exhaust blocked? p.33
No picture
•
•
•
•
•
Is the projector turned on? p.21
Is the mute function on? p.24
Is the brightness setting minimized? p.28
Are the connections set up correctly? p.18
Are all the connected devices functioning properly?
No audio
•
•
•
•
•
Is the projector turned on? p.21
Is the mute function on? p.24
Is the volume setting minimized? p.22
Are the connections set up correctly? p.18
Are all the connected devices functioning properly?
Picture not
displayed
correctly
•
•
•
•
•
Is the input signal supported by the projector? p.36 , p.37
Is the correct video mode selected? p.23
Is the correct signal format selected? p.23
Is the selecting of computer or Y/PB/PR input correct? p.21
Is there something generating an abnormal video signal, for
instance the video tape?
Picture blurred
Part of picture
out of focus
Consumption Power
Weight
External Dimensions
(including protruding parts)
Cabinet material*
Conditions for usage environment
Display method
Panel size
LCD Panel Drive system
Picture
elements
Lens
Lamp
Projection screen size
Projection distance
Speaker
COMPUTER-1,2 terminals
MONITOR terminal
S-VIDEO terminal
VIDEO terminal
AUDIO terminal
Connection terminal
If This Happens
No power
Item
Specification
220 W
2.2 kg
277 × 82 × 204 mm (W × H × D)
PC+ABS resin and ABS resin
Temp: 0°C to 35°C; relative humidity: 30% to 70%
3-panel transmission
0.7 inches
TFT active matrix
TLP-T50/T50M: 786,432 pixels (1,024H × 768V)
TLP-S30
: 480,000 pixels (800H × 600V)
Zoom lens F=1.9-2.2 f=27-32.5 mm
High-pressure mercury lamp
32-300 inches
1.41-11.45 m
1 W (Monaural)
Mini D sub 15 pin RGB / Y/PB/PR (dual use)
Mini D sub 15 pin RGB / Y/PB/PR (dual use)
Mini DIN 4 pin
RCA Pin Jack, 1 V (p-p), 75 Ω
3.5mm dia. stereo mini-jack, 1.5V (rms); 22 kΩ or more
* Each plastic part displays the materials it is made from, in order to facilitate recycling after this
product’s use had ended.
• Is the lens dirty? p.31
• Is the lens focus adjusted optimally? p.22
• Is the projection distance within the projector’s supported range?
p.17
• Is the projector’s screen placement angle tilted too far? p.17
• Are the sharpness or sampling phase adjustments off? p.28 p.23
Image is dark
• Are the brightness or contrast adjustments off? p.28
• Is the lamp nearing the end of its service life? p.26
Colors too light
Bad shading
• Are the color, tint, R-level, G-level, or B-level adjustments off?
• Is the screen dirty?
• Is the lamp nearing the end of its service life? p.26
Remote control
doesn’t work
•
•
•
•
p.28
34
Others
Are the remote control’s batteries drained?
Are the batteries inserted into the remote control correctly? p.16
Is the remote control being used within the effective range? p.16
Are there any obstructions between the remote control and
projector?
• Are there any fluorescent or other bright lights shining at the
projector’s infrared remote sensor?
35
Specifications (Continued)
■ List of supported signals (Y/PB/PR signals)
This projector supports the following RGB signals. Note, however, that depending on the
computer model, the screen may show flicker or streaking. Please adjust the projector if
this happens.
(Press the AUTO SET button, and adjust automatically or manually. p.23 )
Resolution
Mode
720 x 400
640 x 480
720x400_85
VGA_60
VGA_72
VGA_75
VGA_85
SVGA_56
SVGA_60
SVGA_72
SVGA_75
SVGA_85
MAC16"
XGA_43i
XGA_60
XGA_70
XGA_75
XGA_85
MAC19"
SXGA1_75
QuadVGA_60
QuadVGA_85
SXGA3_60
SXGA3_75
SXGA3_85
SXGA+
UXGA_60
UXGA_65
UXGA_70
UXGA_75
UXGA_85
1792x1344_60
1856x1392_60
1920x1440_60
800 x 600
832 x 624
1024 x 768
1152 x 864
1280 x 960
1280 x 1024
1400 x 1050
1600 x 1200
1792 x 1344
1856 x 1392
1920 x 1440
Refresh rate
(Hz)
85.039
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
74.550
86.957
60.004
70.069
75.029
84.997
74.700
75.000
60.000
85.002
60.020
75.025
85.024
60.012
60.000
65.000
70.000
75.000
85.000
60.000
60.000
60.000
H-frequency
(kHz)
37.927
31.469
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
49.725
35.522
48.363
56.476
60.023
68.667
60.134
67.500
60.000
85.938
63.981
79.976
91.146
63.973
75.000
81.250
87.500
93.750
106.250
83.640
86.333
90.000
Clock
(MHz)
35.500
25.175
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
57.283
44.900
65.000
75.000
78.750
94.500
79.857
108.000
108.000
148.500
108.000
135.000
157.500
118.094
162.000
175.500
189.000
202.500
229.500
204.750
218.250
234.000
Note
• Signals whose resolution exceeds the LCD panel’s number of pixels p.35 will be
compressed. For this reason, some information may be lost, or image quality may be
affected.
36
Signal format
fh(kHz)
fv(Hz)
480i(525i)@60Hz
15.73
59.94
480p(525p)@60Hz
576i(625i)@50Hz
31.47
15.63
59.94
50.00
576p(625p)@50Hz
720p(750p)@60Hz
720p(750p)@50Hz
1080i(1125i)@60Hz
1080i(1125i)@50Hz
1035i(1125i)@60Hz
1152i(1250i)@50Hz
31.25
45.00
37.50
33.75
28.13
33.75
31.25
50.00
60.00
50.00
60.00
50.00
60.00
50.00
■ List of supported signals (Video, S-Video signals)
Video mode
NTSC
PAL
SECAM
fh(kHz)
15.73
15.63
15.63
fv(Hz)
60
50
50
fsc(MHz)
3.58
4.43
4.25 or 4.41
PAL-M
PAL-N
PAL-60
NTSC4.43
15.73
15.63
15.73
15.73
60
50
60
60
3.58
3.58
4.43
4.43
■ Pin assignment of COMPUTER & MONITOR terminals
11
6
1
15
10
Pin
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
5
Mini D sub 15 Pin connector
Input Signal
• RGB input
R/G/B signals:
0.7V (p-p) 75 Ω
Horizontal sync signal: TTL level (Pos/neg polarity)
Vertical sync signal: TTL level (Pos/neg polarity)
• Y/PB/PR input
Y signal:
PB/PR signals:
1.0V (p-p) 75 Ω
0.7V (p-p) 75 Ω
Pin description
During RGB input
During Y/PB/PR input
Video signal (R)
Color difference signal (PR)
Video signal (G)
Luminance signal (Y)
Video signal (B)
Color difference signal (PB)
GND
∗
GND
∗
GND (R)
GND (PR)
GND (G)
GND (Y)
GND (B)
GND (PB)
N.C
∗
GND
∗
GND
∗
N.C
∗
Horizontal sync signal
∗
Vertical sync signal
∗
N.C
∗
∗ Do not connect anything.
37
Others
■ List of supported signals (RGB signals)
■ CONTROL terminal
● Pin assignment
1
Pin No.
1
2
3
4
5
6
7
8
2
4
3
5
6
8
7
Signal Name
RXD
CTS
DSR
GND
RTS
N.C
TXD
N.C
Description
Receiving data
Consent to send
Data set ready
Signal ground
Request to send
No connection
Sending data
No connection
Mini DIN 8 pin connector
● Interface format
1 Communication method
2 Communication format
3 Data format
4 Replies
RS-232C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length:
1 bit
STX (02h) Command (3Byte) ETX (03h)
Only 1 command valid per communication.
For input commands, only ASCII-compliant all-uppercase
alphanumeric characters supported.
Acknowledge ACK (06h) No acknowledge NAK (15h)
If commands are to be sent consecutively, wait for the response from the projector
(ACK or NAK) before sending the next command.
● Main Commands
Item
Power on
Power off
OSD display on
OSD display off
Auto setting (RGB input)
Status display on
Status display off
Command
PON
POF
MO0
MO1
PAT
DON
DOF
Item
Computer input select
Y/PB/PR input select
Video input select
S-video input select
Command
IN1
IN2
IN5
IN6
Note
Others
• Contact your dealer for control cable and other commands.
■ Separately Sold Product
Replacement Lamp
Model TLPLV1
Note
• Design, specifications, etc. subject to change without notice for improvements, etc.
38
39