Instruction manual | Delta 17-950L Drill User Manual

17-950L
10" Contractors Saw
(Model 36-978/36-979)
16-1/2” (419 mm)
Laser Crosshair Drill
Press
Perceuse à colonne
de 432 mm
(16-1/2 po) avec
laser à cible
croisée
Taladro de banco
de 432 mm
(16-1/2 pulg)
con objetivo láser en
cruz
Instruction Manual
Manuel d’Utilisation
Manual de Instrucciones
FRANÇAISE (23)
ESPAÑOL (43)
www.deltamachinery.com
(800) 223-7278 - US
(800) 463-3582 - CANADA
A14929 _ 01-07-06 _Rev. D
Copyright © 2006 Delta Machinery
TABLE OF CONTENTS
TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SAFETY GUIDELINES - DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ADDITIONAL SPECIFIC SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ADDITIONAL SAFETY RULES FOR THE LASER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CARTON CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ESPAÑOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
IMPORTANT SAFETY INSTRUCTIONS
Read and understand all warnings and operating instructions before using any tool or equipment.
When using tools or equipment, basic safety precautions should always be followed to reduce the risk of
personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious
injury and property damage. There are certain applications for which tools and equipment are designed. Delta
Machinery strongly recommends that this product NOT be modified and/or used for any application other than
for which it was designed.
If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery
and we have advised you.
Online contact form at www.deltamachinery.com
Postal Mail: Technical Service Manager
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305
(IN CANADA: 125 Mural St. Suite 300, Richmond Hill, ON, L4B 1M4)
Information regarding the safe and proper operation of this tool is available from the following sources:
Power Tool Institute
1300 Sumner Avenue, Cleveland, OH 44115-2851
www.powertoolinstitute.org
National Safety Council
1121 Spring Lake Drive, Itasca, IL 60143-3201
American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org
ANSI 01.1Safety Requirements for Woodworking Machines, and the U.S. Department of Labor regulations www.osha.gov
SAVE THESE INSTRUCTIONS!
2
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The information it contains relates to
protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you
recognize this information.
Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious
injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury.
Used without the safety alert symbol indicates potentially hazardous situation which, if not
avoided, may result in property damage.
CALIFORNIA PROPOSITION 65
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, always
wear NIOSH/OSHA approved, properly fitting face mask or respirator when using such tools.
TOOL WARNING LABELS
3
GENERAL SAFETY RULES
RISK OF UNSAFE OPERATION. Read and understand all warnings and operating instruc-
tions before using this equipment. failure to follow all instructions listed below, may result in
electric shock, fire, and/or serious personal injury or property damage.
IMPORTANT SAFETY INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14. USE THE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an extension
cord, be sure to use one heavy enough to carry the current
your product will draw. An undersized cord will cause a drop
in line voltage, resulting in loss of power and overheating. See
the Extension Cord Chart for the correct size depending on
the cord length and nameplate ampere rating. If in doubt, use
the next heavier gauge. The smaller the gauge number, the
heavier the cord.
15. SECURE THE WORKPIECE. Use clamps or a vise to hold the
workpiece when practical. Loss of control of a workpiece can
cause injury.
16. FEED THE WORKPIECE AGAINST THE DIRECTION OF
THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE
SURFACE. Feeding it from the other direction will cause the
workpiece to be thrown out at high speed.
17. DON’T FORCE THE WORKPIECE ON THE MACHINE.
Damage to the machine and/or injury may result.
18. DON’T OVERREACH. Loss of balance can make you fall into
a working machine, causing injury.
19. NEVER STAND ON THE MACHINE. Injury could occur if the tool
tips, or if you accidentally contact the cutting tool.
20. NEVER LEAVE THE MACHINE RUNNING UNATTENDED.
TURN THE POWER OFF. Don’t leave the machine until it comes
to a complete stop. A child or visitor could be injured.
21. TURN THE MACHINE “OFF”, AND DISCONNECT THE
MACHINE FROM THE POWER SOURCE before installing or
removing accessories, changing cutters, adjusting or changing
set-ups. When making repairs, be sure to lock the start switch
in the “OFF” position. An accidental start-up can cause injury.
22. MAKE YOUR WORKSHOP CHILDPROOF WITH
PADLOCKS, MASTER SWITCHES, OR BY REMOVING
STARTER KEYS. The accidental start-up of a machine by a
child or visitor could cause injury.
23. STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE
COMMON SENSE. DO NOT USE THE MACHINE WHEN
YOU ARE TIRED OR UNDER THE INFLUENCE OF DRUGS,
ALCOHOL, OR MEDICATION. A moment of inattention while
operating power tools may result in injury.
24.
USE OF THIS TOOL CAN GENERATE AND
DISBURSE DUST OR OTHER AIRBORNE PARTICLES,
INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST
AND ASBESTOS DUST. Direct particles away from face
and body. Always operate tool in well ventilated area and
provide for proper dust removal. Use dust collection system
wherever possible. Exposure to the dust may cause serious
and permanent respiratory or other injury, including silicosis (a
serious lung disease), cancer, and death. Avoid breathing the
dust, and avoid prolonged contact with dust. Allowing dust to
get into your mouth or eyes, or lay on your skin may promote
absorption of harmful material. Always use properly fitting
NIOSH/OSHA approved respiratory protection appropriate for
the dust exposure, and wash exposed areas with soap and
water.
FOR YOUR OWN SAFETY, READ THE INSTRUCTION
MANUAL BEFORE OPERATING THE MACHINE. Learning
the machine’s application, limitations, and specific hazards
will greatly minimize the possibility of accidents and injury.
WEAR EYE AND HEARING PROTECTION. ALWAYS
USE SAFETY GLASSES. Everyday eyeglasses are NOT
safety glasses. USE CERTIFIED SAFETY EQUIPMENT.
Eye protection equipment should comply with ANSI Z87.1
standards. Hearing equipment should comply with ANSI
S3.19 standards.
WEAR PROPER APPAREL. Do not wear loose clothing,
gloves, neckties, rings, bracelets, or other jewelry which may
get caught in moving parts. Nonslip protective footwear is
recommended. Wear protective hair covering to contain long
hair.
DO NOT USE THE MACHINE IN A DANGEROUS
ENVIRONMENT. The use of power tools in damp or wet
locations or in rain can cause shock or electrocution. Keep
your work area well-lit to prevent tripping or placing arms,
hands, and fingers in danger.
MAINTAIN ALL TOOLS AND MACHINES IN PEAK
CONDITION. Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing
accessories. Poorly maintained tools and machines can further
damage the tool or machine and/or cause injury.
CHECK FOR DAMAGED PARTS. Before using the machine,
check for any damaged parts. Check for alignment of moving
parts, binding of moving parts, breakage of parts, and any
other conditions that may affect its operation. A guard or any
other part that is damaged should be properly repaired or
replaced with Delta or factory authorized replacement
parts. Damaged parts can cause further damage to the
machine and/or injury.
KEEP THE WORK AREA CLEAN. Cluttered areas and benches
invite accidents.
KEEP CHILDREN AND VISITORS AWAY. Your shop is a
potentially dangerous environment. Children and visitors can be
injured.
REDUCE THE RISK OF UNINTENTIONAL STARTING. Make
sure that the switch is in the “OFF” position before plugging
in the power cord. In the event of a power failure, move the
switch to the “OFF” position. An accidental start-up can cause
injury. Do not touch the plug’s metal prongs when unplugging
or plugging in the cord.
USE THE GUARDS. Check to see that all guards are in place,
secured, and working correctly to prevent injury.
REMOVE ADJUSTING KEYS AND WRENCHES BEFORE
STARTING THE MACHINE. Tools, scrap pieces, and other
debris can be thrown at high speed, causing injury.
USE THE RIGHT MACHINE. Don’t force a machine or an
attachment to do a job for which it was not designed. Damage
to the machine and/or injury may result.
USE RECOMMENDED ACCESSORIES. The use of
accessories and attachments not recommended by Delta
may cause damage to the machine or injury to the user.
4
ADDITIONAL SPECIFIC SAFETY RULES
RISK OF UNSAFE OPERATION. Failure to follow these rules may result in serious injury.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
DO NOT OPERATE THIS MACHINE until it is completely
assembled and installed according to the instructions. A
machine incorrectly assembled can cause serious injury.
OBTAIN ADVICE from your supervisor, instructor, or
another qualified person if you are not thoroughly familiar
with the operation of this machine. Knowledge is safety.
FOLLOW ALL WIRING CODES and recommended electrical
connections to prevent shock or electrocution.
SECURE THE MACHINE TO A SUPPORTING SURFACE.
Vibration can cause the machine to slide, walk, or tip over.
NEVER START THE MACHINE BEFORE CLEARING
THE TABLE OF ALL OBJECTS (tools, scrap pieces,
etc.). Debris can be thrown at high speed.
NEVER START THE MACHINE with the drill bit, cutting
tool, or sanding drum against the workpiece. Loss of
control of the workpiece can cause serious injury.
PROPERLY LOCK THE DRILL BIT, CUTTING TOOL, OR
SANDING DRUM IN THE CHUCK before operating this
machine.
REMOVE THE CHUCK KEY BEFORE STARTING THE
MACHINE. The chuck key can be thrown out at a high
speed.
TIGHTEN ALL LOCK HANDLES before starting the machine.
Loss of control of the workpiece can cause serious injury.
USE ONLY DRILL BITS, CUTTING TOOLS, SANDING
DRUMS, OR OTHER ACCESSORIES with shank size
recommended in your instruction manual. The wrong
size accessory can cause damage to the machine and/or
serious injury.
USE ONLY DRILL BITS, CUTTING TOOLS, OR
SANDING DRUMS that are not damaged. Damaged
items can cause malfunctions that lead to injuries.
USE RECOMMENDED SPEEDS for all operations. Other
speeds may cause the machine to malfunction causing
damage to the machine and/or serious injury.
AV O I D AW K WA R D O P E R AT I O N S A N D H A N D
POSITIONS. A sudden slip could cause a hand to move
into the bit.
14. KEEP ARMS, HANDS, AND FINGERS away from the bit.
Serious injury to the hand can occur.
15. HOLD THE WORKPIECE FIRMLY AGAINST THE
TABLE. Do not attempt to drill a workpiece that does
not have a flat surface against the table, or that is not
secured by a vise. Prevent the workpiece from rotating by
clamping it to the table or by securing it against the drill
press column. Loss of control of the workpiece can cause
serious injury.
16. TURN THE MACHINE “OFF” AND WAIT FOR THE DRILL
BIT, CUTTING TOOL, OR SANDING DRUM TO STOP
TURNING prior to cleaning the work area, removing
debris, removing or securing work-piece, or changing
the angle of the table. A moving drill bit, cutting tool, or
sanding drum can cause serious injury.
17. PROPERLY SUPPORT LONG OR WIDE work-pieces.
Loss of control of the workpiece can cause severe injury.
18. NEVER PERFORM LAYOUT, ASSEMBLY OR SET-UP
WORK on the table/work area when the machine is
running. Serious injury can result.
19. TURN THE MACHINE “OFF”, disconnect the machine
from the power source, and clean the table/work area
before leaving the machine. LOCK THE SWITCH IN THE
“OFF” POSITION to prevent unauthorized use. Someone
else might accidentally start the machine and cause
serious injury to themselves.
20. ADDITIONAL INFORMATION regarding the safe and
proper operation of power tools (i.e. a safety video)
is available from the Power Tool Institute, 1300
Sumner Avenue, Cleveland, OH 44115-2851 (www.
powertoolinstitute.com). Information is also available
from the National Safety Council, 1121 Spring Lake
Drive, Itasca, IL 60143-3201. Please refer to the
American National Standards Institute ANSI 01.1 Safety
Requirements for Woodworking Machines and the
U.S. Department of Labor OSHA 1910.213 Regulations.
SAVE THESE INSTRUCTIONS.
Refer to them often
and use them to instruct others.
5
ADDITIONAL SAFETY RULES FOR THE LASER
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.
EYE INJURY -LASER LIGHT
*
*
Do not stare into beam aperture, or into a reflection from a mirror-like surface
Do not use optical tools such as a telescope or transit to view the laser beam
*
*
*
*
EYE INJURY - LASER LIGHT
Do not operate the laser around children or allow children to operate the laser.
Store idle laser out of reach of children and other untrained persons
Turn the laser off when it is not in use
Do not disassemble laser module. The class II laser output could be exceeded if the unit is disassembled. Laser complies
with 21 CFR 1040.10 and 1040.11.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
EXPLOSION HAZARD. Do not operate the laser or drill press in explosive atmospheres such as in the
presence of flammable liquids, gases, or dust. A spark could ignite the dust or fumes.
NOTE: Do not remove or deface warning labels.
6
POWER CONNECTIONS
A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should
be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have
3-prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the
machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of
the same characteristics as indicated on the machine. All line connections should make good contact. Running on low
voltage will damage the machine.
Electrocution hazard. Do not expose the machine to rain or operate the machine in damp locations.
MOTOR SPECIFICATIONS
Your machine is wired for 120 Volts 60 HZ alternating current. Before connecting the machine to the power source, make
sure the switch is in the “OFF” position.
GROUNDING INSTRUCTIONS
Electrocution hazard. This machine must be grounded while in use to protect the operator from
electric shock.
1. All grounded, cord-connected machines:
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to
reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor
with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding
conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding
conductorto a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or
if in doubt as to whether the machine is properly grounded.
Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that
accept the machine’s plug, as shown in Fig. A.
Repair or replace damaged or worn cord immediately.
2. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less
than 150 volts:
If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the
machine will have a grounding plug that looks like the plug illustrated in Fig. A. A temporary adapter, which looks like
the adapter illustrated in Fig. B, may be used to connect this plug to a matching 2-conductor receptacle as shown
in Fig. B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly
grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the like, extending
from the adapter must be connected to a permanent ground such as a properly grounded outlet box. Whenever the
adapter is used, it must be held in place with a metal screw.
NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.
Electrocution hazard. In all cases, make certain that the receptacle in question is properly
grounded. If you are not sure, have a qualified electrician check the receptacle.
GROUNDED OUTLET BOX
GROUNDED OUTLET BOX
GROUNDING MEANS
CURRENT
CARRYING
PRONGS
ADAPTER
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
Fig. A
Fig. B
7
EXTENSION CORDS
Use proper extension cords. Imroper cord gauge can cause overheating. Make sure your extension cord
is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and matching receptacle
which will accept the machine’s plug. When using an extension cord, be sure to use one heavy enough to carry the
current of the machine. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating.
Fig. D-1 shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating
0-6
0-6
0-6
0-6
6-10
6-10
6-10
6-10
10-12
10-12
10-12
10-12
12-16
12-16
12-16
Volts
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
Total
Length of
Cord in
Feet
up to 25
25-50
50-100
100-150
up to 25
25-50
50-100
100-150
up to 25
25-50
50-100
100-150
up to 25
25-50
Gauge of Extension
Cord
18 AWG
16 AWG
16 AWG
14 AWG
18 AWG
16 AWG
14 AWG
12 AWG
16 AWG
16 AWG
14 AWG
12 AWG
14 AWG
12 AWG
GREATER THAN 50 FEET NOT RECOMMENDED
Fig. D-1
FUNCTIONAL DESCRIPTION
FOREWORD
The Delta 17-950L drill press is a 16-1/2" drill press with a laser guide and a large woodworker's table (14x18 inches).
The table can tilt forward and side to side and comes with T-slots for use with many drill press accessories. The 17-950L
also comes with a 120V, 1/2 H.P. induction motor and a flexible lamp. This drill press has a 5/8” capacity chuck and a 3
7/8” stroke. There are 12 speed options, ranging from 250 rpm to 3000 rpm for optimum drilling performance in a variety
of materials.
NOTICE: The photo on the manual cover illustrates the current production model. All other illustrations contained in the
manual are representative only and may not depict the actual labeling or accessories included. These are intended to
illustrate technique only.
8
CARTON CONTENTS
6
12
7
1
3
8
13
9
14
10
15
11
16
4
18
17
19
2
5
20
21
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
Drill Press Head
Table
Table Bracket and Column
Light
Base
Chuck
Handle (3)
Spindle Adapter
Drift Key
5mm Hex Wrench
3mm Hex Wrench
Table Raising and Lowering Handle
Table Clamp Handle
Chuck Key
(2) M8x1.25x125mm carriage head screws, (4) flat
washers, (2) lockwashers, and (2) hex nuts (for
fastening drill press to a supporting surface)
M10x1.5x40mm Hex Head Screws (4)
M6x1x12mm Hex Cap Head Screw (2)
1/4" Washer
Cord Strain Relief
Cord Clamp (2)
Cord Bushing
Table insert
Screws (2)
Springs (2)
Forward tilt levers
Screws (2)
Laser
Laser Alignment Rod
Hex Head Cap Screws (2)
4mm Hex Wrench
14mm Hex Wrench (Not Shown)
24
23
25
22
26
27
28
29
30
UNPACKING AND CLEANING
Carefully unpack the machine and all loose items from the shipping container(s). Remove the rust-preventative oil from
unpainted surfaces using a soft cloth moistened with mineral spirits, paint thinner or denatured alcohol.
FIRE HAZARD. Do not use highly volatile solvents such as gasoline, naphtha, acetone or lacquer thinner for cleaning
your machine. Such materials can easily catch fire. After cleaning, cover the unpainted surfaces with a good quality household
floor paste wax.
9
ASSEMBLY
RISK OF UNSAFE OPERATION. For your own safety, do not connect the machine to the power source
until the machine is completely assembled and you read and understand the entire instruction manual.
ASSEMBLY TOOLS REQUIRED
3mm and 5mm hex wrench (supplied)
10mm, 17mm, 24mm open end or socket wrenches (not supplied)
ASSEMBLY TIME ESTIMATE
Assembly for this machine takes approximately 30 minutes to 1 hour.
1. If you plan to use your drill press in a permanent
location, you must secure the drill press base to the
supporting surface with fasteners through the two
mounting holes (A) Fig. 3 in the drill press base.
A
RISK OF UNSAFE OPERATION. If you
do not fasten your drill press in a permanent manner,
you must fasten the drill press to a plywood mounting
board to prevent the drill press from tipping over
during normal use.
Fig. 3
RISK OF UNSAFE OPERATION. Use
a good grade of plywood with a minimum 3/4"
thickness. Do not make the mounting board from
particle board since particle board breaks easily.
28
"M
IN
IM
UM
2. Use a plywood board base with the minimum
dimensions as shown in Fig. 4 for mounting the drill
press base to a supporting surface.
3. Place the drill press base (D) Fig. 5 centered on the
supporting surface (E).
RISK OF UNSAFE OPERATION. Make
sure that the plywood extends a minimum of 3" on all
four sides of the base as shown in Fig. 5.
C
4. Drill two 3/8" diameter holes through the holes (A)
Fig. 3 in the drill press base, and in the supporting
surface (E) Fig. 5.
21"
MIN
IMU
M
Fig. 4
NOTE: Place a piece of scrap wood underneath the
supporting surface when drilling the through holes so
that the drill bit will not damage the material beneath
the supporting surface.
3" MINIMUM
3" MINIMUM
5. Fasten the drill press base to the mounting board
using the carriage bolts, flat washers, lockwashers,
and hex nuts (C) Fig. 4 furnished with your drill
press. Countersink the holes for the carriage bolt
heads and flat washers under the board so that
the bolt heads are flush with or below the bottom
surface of the board. Use a flat washer, lock washer,
and hex nut above the drill press base as shown at
(F) Fig. 5.
F
D
3" MINIMUM
3" MINIMUM
E
Fig. 5
10
RISK OF UNSAFE OPERATION. You must secure the plywood base to the floor or supporting
surface if the drill press has any tendency to vibrate, slide, or walk during normal operation.
6. Attach the column (A) Fig. 6 to the base (B) using the four M10x40mm hex head screws (C), three of which are
shown.
7. Attach the table adjusting handle (D) Fig. 7 to the worm gear shaft (E). Tighten the screw (F) against the flat on the
shaft with the 3mm wrench supplied.
8. Thread the table clamp handle (G) Fig. 8 in the hole in rear of table bracket.
F
A
C
C
D
E
B
G
Fig. 6
Fig. 8
Fig. 7
LIFTING HAZARD. The drill press table is heavy. Two people may be needed to attach it to the drill
press column.
9. To attach the table to the knuckle, align the pilot face (H) Fig. 9 of the knuckle (K) with the table support (J) before
tightening the table bolt (D) Fig. 10A with the 14mm hex wrench.
10. Check the scale (F) Fig. 9. Ensure the hairline pointer (E) Fig. 10 on the knuckle lines up with zero (0) on the scale (F)
on the table support.
11. To attach the forward tilt locking lever (G) Fig. 10A, place the lever on the trunnion clamp nut (H).
12. Place the spring (I) on the slotted screw (J). Insert the screw into the lever and trunnion clamp nut.
13. Tighten the screw (J) until it bottoms. The lever should move up and down on the screw.
F
K
H
J
Fig. 10
Fig. 9
D
H
G
E
F
I
Fig. 11
Fig. 12
11
J
EYE INJURY - LASER LIGHT. Do not stare into the laser beam or aperture or into a reflection
from a mirror-like surface.
14. Use the two socket head cap screws (C) Fig. LA2 included in laser packaging and the supplied 4mm hex wrench
to attach the front laser housing (A) Fig. LA1 to the rear laser housing (B) loosely.
B
A
A
Fig. LA2
Fig. LA1
15. Place this laser housing assembly on the drill press
column (D) Fig. LA3. Rest it on the collar (E) Fig.
LA3.
16. Tighten the screws (C) Fig. LA2, making sure that
one laser is positioned on each side of the column
(D), (Fig. LA3).
17. Remove the battery cover (F) Fig. LA4 from the laser
housing.
18. Connect a 9-volt battery (G) (not included) to the
battery terminal (H).
19. Place the battery in the compartment (I). Replace
the cover.
20. Place the drill press head (K) Fig. 11 on the column
as far as it will go. Align the head (K) Fig. 12 with the
table (L) Fig. 12 and base (M) Fig. 12. Tighten the
two head-locking screws (N) Fig. 11 with the 5mm
wrench supplied.
D
E
Fig. LA3
H
K
G
F
Fig. LA4
L
K
N
M
Fig. 11
Fig. 12
12
IMPORTANT: Make certain that the tapered hole in the
bottom of spindle (T) Fig. 13, and the taper on the spindle
adapter (U) are clean and free of grease, lacquer, or rustpreventive coatings.
NOTE: Household oven cleaner can effectively remove
these coatings from the spindle and spindle adapter.
However, carefully follow the manufacturer’s safety rules
regarding its use.
T
V
U
21. Push the spindle adapter (U) Fig. 13 into the spindle
(T). making certain that the tang (V) engages the
mating slot inside the spindle (T).
Fig. 13
RISK OF PROPERTY DAMAGE. To
avoid damage to the laser, prevent contact of the
laser pod with a cleaning solution. You can clean the
laser pod with a dry cotton cloth.
IMPORTANT: Make certain the spindle taper (O) Fig. 14,
and tapered hole in chuck (P) are clean and free of any
grease, lacquer or rust preventive coatings.
NOTE: Household oven cleaner can effectively remove
any substance from the chuck. However, carefully follow
the manufacturer's safety rules concerning its use.
IMPORTANT: Open the chuck jaws as wide as possible,
making sure that the chuck jaws are inside the chuck.
O
P
Fig. 14
22. Holding chuck on taper of spindle, tap with a soft tip
hammer (Q) or a block of wood and hammer to set
chuck, as shown in Fig. 15.
RISK OF PROPERTY DAMAGE. To
avoid damage to the chuck, NEVER drive the chuck on
the spindle with a metal hammer.
Q
Fig. 15
23. Thread the three pinion shaft handles (R) in the three
holes located in the pinion shaft hub (S) Fig. 16.
S
R
Fig. 16
13
24. Align the two holes in the lamp bracket (A) Fig. 17, with the two holes (B) on the side of the drill press head.
25. Place the cord bushing (C) Fig. 17, around the top of the lamp cord (D)
26. Align the two holes in the lamp cord bracket (F) Fig. 18 with the two holes in the lamp bracket (A) and drill press
head.
27. Place a 1/4" washer onto a M6x1x12mm cap head screw. Insert the screw (G) Fig. 18 through the hole in the cord
strain relief bracket and the lamp bracket and thread the screw into the drill press head. Repeat this process for
the remaining hole in the cord strain relief bracket and tighten both screws securely.
A
B
F
A
C
G
D
Fig. 17
Fig. 18
28. Peel backing from cord clamp (H) Fig. 19, and apply
clamp at the location shown. Make certain the lamp
cord is routed out of the way of the drill, then secure
cord (J) to cord clamp (H) as shown in Fig. 19.
H
J
OPERATIONS
OPERATIONAL CONTROLS
AND ADJUSTMENTS
Fig. 19
STARTING AND STOPPING THE DRILL PRESS
The switch (A) Fig. 20 is located on the front of the drill press head. To turn the drill press “ON” move the switch up
to the “ON” position. To turn the drill press “OFF” move the switch down to the “OFF” position.
RISK OF PERSONAL INJURY. Make sure that the switch is in the “OFF” position before plugging in
the power cord. In the event of a power failure, move the switch to the “OFF” position. an accidental start-up can
cause injury.
LOCKING THE SWITCH IN THE “OFF” POSITION
IMPORTANT: When the machine is not in use, the switch should be locked in the “OFF” position to prevent
unauthorized use. This can be done by grasping the switch toggle (B) and pulling it out of the switch, as shown in Fig.
21. With the switch toggle (B) removed, the switch will not operate. However, should the switch toggle be removed
while the drill press is operating, the switch can be turned “OFF” once, but cannot be restarted without inserting the
switch toggle (B).
B
A
Fig. 20
Fig. 21
14
FLEXIBLE LAMP
The flexible lamp operates independently of the drill press. To turn the lamp “ON” and “OFF”, rotate switch (A) Fig.
22.
FIRE HAZARD. To reduce the risk of
fire, use 40 watt or less, 120 volt, reflector track type
light bulb (not supplied). DO NOT USE a standard
household light bulb. Do not allow the reflector tracktype light bulb to extend below the lamp shade.
A
RISK OF PERSONAL INJURY. Disconnect
the machine from the power source before making
any adjustments.
Fig. 22
TABLE ADJUSTMENTS
RISK OF PERSONAL INJURY. Make sure that nothing is on the table and that the workpiece is
clamped down. Falling objects can cause an injury.
You can tilt the table forward from zero (0) to 45 degrees. To adjust:
1. Loosen the two forward tilt levers (A) Fig. 23.
2. Adjust the table to your desired angle. The scale (B) Fig. 23 is located on the side of the table support.
3. Tighten the levers (A) Fig. 23.
4. A positive stop (C) Fig. 24 is provided to return the table to the zero position. Adjust this stop by turning the screw/
stop (C), located under the table. Tighten the locknut to secure the stop.
You can tilt the table right or left. Positive stops are included for 0, 45 and 90 degrees. To adjust:
1. Loosen the table bolt (E) Fig. 25 approximately 1/4 turn with the supplied 14mm hex wrench.
2. Pull out the spring-loaded detent pin (F).
3. Rotate the table to your desired angle. The tilt scale (G) Fig. 25A is located on the knuckle behind the table. Use
this scale for accuracy. You can allow the detent pin to slide in to the positive stops, but check your scale to be
sure of the exact angle.
4. Tighten the table bolt.
C Located under table
B
A
Fig. 23
Fig. 24
E
G
F
Fig. 25
Fig. 25A
15
TABLE INSERT
The drill press table comes with an insert (H) Fig. 26 made of MDF to help prevent wear and tear on the bit when it
drills down through the workpiece. To adjust:
1. Place the insert (H) Fig. 26 in the hole in the table.
2. If the insert is not level with the table, adjust the four jack screws (J) Fig. 27A. When the table is level, tighten the
locking nut on each screw.
3. Secure the insert with the 2 provided screws.
H
J
Fig. 26
Fig. 27A
T-SLOTS
The drill press table is fitted with two T-slots (L) Fig. 27B
for use with various drill press accessories (stop blocks,
fences, or clamps). Use 5/16" T-bolts when attaching
your accessory to the table.
L
ADJUSTING THE LASERS
Fig. 27B
Disconnect the machine from the power source.
LASER LIGHT. Do not stare into the beam, aperture, or into a reflection from a mirror-like surface.
MAKING THE LASERS PARALLEL
1. Install the alignment pin (A) in the chuck (B). Make
sure that the pointed end (C) of the alignment pin
is down (Fig. L1). The black scribed line on the pin
should face toward the left laser.
2. Turn on the lasers using the switch (D) on the front of
the laser housing.
3. With a Phillips screwdriver, remove the two screws
(F) Fig. L2 and cap (G) above the left side of the
laser housing.
4. Loosen the laser retainer screw (H) Fig. L3.
5. Move the laser lever (I) Fig. L3 so that the laser is
shining on the alignment pin. Adjust the lever (I) until
the laser is parallel with the black line.
NOTE: You may have to move the laser holder (J) Fig. L1
to get the laser to shine on the alignment pin. Once the
light is on the pin, adjust the laser with the lever (I).
6. When the laser is set, tighten the laser retainer screw
(H) Fig. L3. Replace the cap (G) Fig L2 and loosely
tighten the two screws (F).
7. Repeat for the otherside.
J
B
D
A
Fig. L1
C
I
H
F
G
Fig. L2
16
Fig. L3
MAKING THE LASERS INTERSECT
1.
2.
3.
4.
Place a piece of wood (A) Fig. L4 on the table and clamp it in place.
Use the handle (B) to lower the quill (C). Make an indentation in the wood with the alignment pin (D) Fig. L4.
Turn on the laser and adjust both beams to intersect at that point by rotating the laser holder (A) Fig. L5.
Ensure that the lasers align at different heights. Raise or lower the table, make a new indentation, and turn on the
lasers. If the lasers do not align at different heights, you will need to check the parallel adjustment.
5. Once the lasers are adjusted, tighten the screws on each side of the laser housing, two of which are shown at (F)
Fig. L2.
B
C
A
D
Fig. L4
A
Fig. L5
SPINDLE SPEEDS
Twelve spindle speeds are available on the drill press. Fig. 28A illustrates the belt positions and the corresponding
speeds.
SPINDLE
CENTER
MOTOR
540
360
250
1090
590
410
1820
1280
650
3000
2180
1450
Fig. 28A
17
CHANGING SPEEDS AND ADJUSTING THE BELT TENSION
NOTE: A belt-positioning speed chart (E) Fig. 28B is located on the inside top cover of the drill press.
Disconnect the machine from the power source!
1. Open the belt and pulley guard (A) Fig. 28B.
2. Loosen the tension lock knobs located on both
sides of the head casting (one shown at (B) Fig.
28B). Move the tension lever (C) forward. Pivot the
motor (D) toward the front of the drill press.
3. Hold the motor toward the front of the drill press,
and position the belts (F) on the desired steps of the
motor and spindle pulleys (Figs. 28A & 28B).
4. Move the motor (D) Fig. 28B to the rear until the belt
is properly tensioned. Tighten the tension lock knob
(B). The belt should be just tight enough to prevent
slipping. Excessive tension will reduce the life of the
belt, the pulleys, and the bearings. When you can
flex the belts approximately 1" at the midway point
between the pulleys, the tension will be correct.
F
A
E
F
B
D
C
Fig. 28B
DRILLING HOLES TO DEPTH
A depth-stop is provided for projects that require a number of holes at the same depth. To use:
Disconnect the machine from the power
source!
B
1. Install your bit in the chuck.
2. Loosen the lock screw (A) Fig. 29. Rotate the pinion
assembly (B) until the pointer (C) aligns (on the scale
(D) Fig. 29) with your desired depth. Tighten the lock
D
screw (A).
3. Place the workpiece on the drill press table. Raise the
drill press table until the workpiece barely touches
the drill bit.
4. Drill a test hole to check the depth.
NOTE: The scale (D) is calibrated in both inches and
B
Fig. 29
millimeters.
B
ADJUSTING SPINDLE RETURN SPRING
The spindle will automatically return to its upper-most position when the handle is released. Allow the handle to return
slowly to the top position after each hole has been drilled. This spindle-return spring was adjusted at the factory.
However, to adjust (if necessary):
Disconnect the machine from the power source!
1. Loosen the nuts (B) and (E) Fig. 30. Make sure that the spring housing (A) stays engaged with the head casting.
2. FIRMLY HOLD the spring housing (A) Fig. 31, pull it out, and rotate it until the boss (D) is engaged with the next
notch in the housing. Turn the housing counter-clockwise to increase or clockwise to decrease the spring tension.
Turn the nut (E) until it contacts the spring housing (A), then back the nut (E) out 1/4 turn. Tighten the nut (B) against
the nut (E) to hold the housing in place.
IMPORTANT: Do not allow the inside nut (E) to contact the spring housing (A).
A
B
D
E
E
B
A
Fig. 31
Fig. 30
18
MACHINE USE
NOTE: Use bits with this drill press that have a shank of 5/8" or less in diameter.
NOTE: Use scrap material for practice to get a feel of the machine before attempting regular work.
RISK OF UNSAFE OPERATION. The use of accessories and attachments not recommended by Delta
may result in risk of injury.
IMPORTANT: If the workpiece is long enough, position it with one end against the left side of the column (Fig. 32). This
action prevents the workpiece from rotating with the drill bit or cutting tool, causing damage to the workpiece or injury
to you. If it is not possible to support the workpiece against the column, fasten it to the table using clamps or a vise.
INSTALLING AND REMOVING DRILL BITS
Disconnect the machine from the power source!
1. Insert smooth end of drill bit (A) Fig. 33, into chuck (B), as far as it will go, and then back the bit out 1/16", or up
to the flutes for small bits.
2. Make certain that the drill bit (A) Fig. 33, is centered in the chuck (B) before tightening the chuck with the key (C).
3. Turn the chuck key (C) Fig. 33, clockwise to tighten and counter-clockwise to loosen the chuck jaws.
4. Tighten all three chuck jaws to secure the drill bit sufficiently so that it does not slip while drilling.
5.
RISK OF FLYING OBJECTS. Don't tether the chuck key to the tool. The cord could get tangled
and chuck key could be thrown at user or tool could be damaged. Also, make sure that the chuck key (C)
Fig. 33, is removed from chuck before starting drill press. Your chuck key (C) is equipped with a self-ejecting pin
(D) which helps minimize the hazard of the key being left in the chuck.
D
B
A
Fig. 32
C
Fig. 33
CORRECT DRILLING SPEEDS
Factors that determine the best drilling speed 1) the workpiece, 2) the size of the hole to be drilled, 3) the type of drill
or other cutter, and 4) the quality of cut.
RISK OF UNSAFE OPERATION. Use the recommended speed for the drill press bit and workpiece
material.
DRILLING WOOD
Twist drills, although intended for metal drilling, may be used for boring holes in wood. However, machine spur bits are
generally preferred for working in wood. These bits cut cut a flat-bottom hole and are designed for removal of wood
chips. Do not use hand bits that have a screw tip. At drill press speeds, they turn too rapidly and will lift the work and
spin it.
For through boring, align the table so that the bit will enter the center hole to avoid damage to the table. Scribe a
vertical line on the front of the column and a matching mark on the table bracket and the drill press head, so that the
table and drill press head can be clamped in the center position at any height.
When the bit is about to cut through the workpiece, feed it slowly to prevent spintering the bottom face. To help protect
the bit and reduce splintering, a wooden insert is included in the table. Alternately, you can use a scrap piece of wood
as a base block under the work.
19
DRILLING METAL
Use clamps to hold the workpiece. DO NOT try to hold the workpiece with your hand. The drill bit may seize the work at
any time and spin, causing damage to the machine and/or injury to you. The drill bit will break if the workpiece strikes
the column.
Clamp the workpiece firmly. Tilting, twisting, or shifting will result in a rough hole and drill bit breakage. For flat work,
lay the workpiece on a wooden base and clamp it firmly against the table. If the workpiece is of irregular shape and
cannot lie flat on the table, make sure that you clamp it securely.
REMOVING SPINDLE ADAPTER
The spindle adapter and chuck can be removed for the purpose of using shanks with a #2 morse taper.
Disconnect the machine from the power source!
1. Align the slot in the quill (A) Fig. 34 with the slot in the spindle (B).
2. Insert the drift key (C) Fig. 35 through the slot in the quill and the slot in the spindle.
3. Tap the drift key (C) Fig. 35 with a hammer until the the spindle adapter and chuck fall from the quill.
B
A
C
Fig. 34
Fig. 35
TROUBLESHOOTING
For assistance with your machine, visit our website at www.deltamachinery.com for a list of service centers or call
the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).
20
MAINTENANCE
KEEP MACHINE CLEAN
LUBRICATION & RUST PROTECTION
Periodically blow out all air passages with dry compressed
air. All plastic parts should be cleaned with a soft damp
cloth. NEVER use solvents to clean plastic parts. They
could possibly dissolve or otherwise damage the material.
Apply household floor paste wax to the machine table,
extension table or other work surface weekly. Or use a
commercially available protective product designed for
this purpose. Follow the manufacturer’s instructions for
use and safety.
To clean cast iron tables of rust, you will need the
following materials: a sheet of medium Scotch-Brite™
Blending Hand Pad, a can of WD-40® and a can of
degreaser. Apply the WD-40 and polish the table surface
with the Scotch-Brite pad. Degrease the table, then apply
the protective product as described above.
Wear certified safety equipment for
eye, hearing and respiratory protection while using
compressed air.
FAILURE TO START
Should your machine fail to start, check to make sure
the prongs on the cord plug are making good contact
in the outlet. Also, check for blown fuses or open circuit
breakers in the line.
SERVICE
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts, visit our website at servicenet.deltamachinery.com.
You can also order parts from your nearest factory-owned branch, or by calling our Customer Care Center at 1-800-223-7278 to
receive personalized support from highly-trained technicians.
SERVICE AND REPAIRS
All quality tools will eventually require servicing and/or replacement of parts. For information about Delta Machinery, its factoryowned branches, or an Authorized Warranty Service Center, visit our website at www.deltamachinery.com or call our Customer
Care Center at 1-800-223-7278. All repairs made by our service centers are fully guaranteed against defective material and
workmanship. We cannot guarantee repairs made or attempted by others.
You can also write to us for information at Delta Machinery, 4825 Highway 45 North, Jackson, Tennessee 38305 - Attention:
Product Service. Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number,
etc.)
ACCESSORIES
A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, and
Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or for the name of
your nearest supplier.
Since accessories other than those offered by Delta have not been tested with this product, use
of such accessories could be hazardous. For safest operation, only Delta recommended accessories should be
used with this product.
21
WARRANTY
To register your tool for warranty service visit our website at www.deltamachinery.com.
Two Year Limited New Product Warranty
Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal
use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service
center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity
to verify the alleged defect by inspection. For all refurbished Delta product, the warranty period is 180 days. Delta may require that electric
motors be returned prepaid to a motor manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible
for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone
other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for incidental or consequential
damages resulting from defective products. This warranty is Delta’s sole warranty and sets forth the customer’s exclusive remedy, with respect
to defective products; all other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are expressly
disclaimed by Delta.
22
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont
des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®, Contractor’s Saw II™, Delta®,
DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®, Grip Vac™, Homecraft®, Jet-Lock®,
JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®,
PORTA-PLANE®, PORTER-CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®,
Q-3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®,
SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design),
The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®,
TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSAPLANE® , WHISPER SERIES®,WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las Marcas Registradas con
el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar registradas en otros países. Marques déposées,
indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305
www.deltamachinery.com
64
Download PDF

advertising