Instruction manual | Delta 18-900L Drill User Manual

(Model DP400)
PART NO. 907453 - 04-13-04
Copyright © 2004 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
ESPAÑOL: PÁGINA 21
1-800-223-7278 (In Canada call 1-800-463-3582).
INSTRUCTION MANUAL
16½" Floor Model Drill Press
SAFETY GUIDELINES - DEFINITIONS
This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the
symbols to the right. Please read the manual and pay attention to these sections.
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may
result in property damage.
SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER
CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
· lead from lead-based paints,
· crystalline silica from bricks and cement and other masonry products, and
· arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear MSHA/NIOSH
approved, properly fitting face mask or respirator when using such tools.
GENERAL SAFETY RULES
READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE
USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,
fire, and/or serious personal injury or property damage.
IMPORTANT SAFETY INSTRUCTIONS
Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there
are certain hazards involved with the operation of the product. Using the machine with respect and caution will
considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored,
personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards,
goggles, dust masks and hearing protection can reduce your potential for injury. But even the best guard won’t make
up for poor judgment, carelessness or inattention. Always use common sense and exercise caution in the workshop.
If a procedure feels dangerous, don’t try it. Figure out an alternative procedure that feels safer. REMEMBER: Your
personal safety is your responsibility. For additional information please visit our website www.deltamachinery.com.
This machine was designed for certain applications only. Delta Machinery strongly recommends that this
machine not be modified and/or used for any application other than that for which it was designed. If you have any
questions relative to a particular application, DO NOT use the machine until you have first contacted Delta to determine
if it can or should be performed on the product.
Technical Service Manager
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305
(IN CANADA: 505 SOUTHGATE DRIVE, GUELPH, ONTARIO N1H 6M7)
2
GENERAL SAFETY RULES
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.
1. FOR YOUR OWN SAFETY, READ THE INSTRUCTION
MANUAL BEFORE OPERATING THE MACHINE.
Learning the machine’s application, limitations, and
specific hazards will greatly minimize the possibility of
accidents and injury.
2. WEAR EYE PROTECTION. ALWAYS USE SAFETY
GLASSES. Also use face or dust mask if cutting
operation is dusty. Everyday eyeglasses are NOT safety
glasses. USE CERTIFIED SAFETY EQUIPMENT. Eye
protection equipment should comply with ANSI Z87.1
standards, hearing equipment should comply with
ANSI S3.19 standards, and dust mask protection
should comply with MSHA/NIOSH certified respirator
standards. Splinters, air-borne debris, and dust can
cause irritation, injury, and/or illness.
3. WEAR PROPER APPAREL. Do not wear loose
clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts. Nonslip
footwear is recommended. Wear protective hair
covering to contain long hair.
4. DO NOT USE THE MACHINE IN A DANGEROUS
ENVIRONMENT. The use of power tools in damp or
wet locations or in rain can cause shock or
electrocution. Keep your work area well-lit to prevent
tripping or placing arms, hands, and fingers in danger.
5. MAINTAIN ALL TOOLS AND MACHINES IN PEAK
CONDITION. Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing
accessories. Poorly maintained tools and machines can further
damage the tool or machine and/or cause injury.
6. CHECK FOR DAMAGED PARTS. Before using the
machine, check for any damaged parts. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, and any other conditions that may
affect its operation. A guard or any other part that is
damaged should be properly repaired or replaced.
Damaged parts can cause further damage to the
machine and/or injury.
7. KEEP THE WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
8. KEEP CHILDREN AND VISITORS AWAY. Your shop is a
potentially dangerous environment. Children and visitors can
be injured.
9. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure that the switch is in the “OFF” position
before plugging in the power cord. In the event of a
power failure, move the switch to the “OFF” position.
An accidental start-up can cause injury.
10. USE THE GUARDS. Check to see that all guards are in
place, secured, and working correctly to prevent injury.
11. REMOVE ADJUSTING KEYS AND WRENCHES
BEFORE STARTING THE MACHINE. Tools, scrap
pieces, and other debris can be thrown at high speed,
causing injury.
12. USE THE RIGHT MACHINE. Don’t force a machine or
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
3
an attachment to do a job for which it was not
designed. Damage to the machine and/or injury may
result.
USE RECOMMENDED ACCESSORIES. The use of
accessories and attachments not recommended by
Delta may cause damage to the machine or injury to the
user.
USE THE PROPER EXTENSION CORD. Make sure
your extension cord is in good condition. When using
an extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized
cord will cause a drop in line voltage, resulting in loss of
power and overheating. See the Extension Cord Chart
for the correct size depending on the cord length and
nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the
heavier the cord.
SECURE THE WORKPIECE. Use clamps or a vise to hold
the workpiece when practical. Loss of control of a
workpiece can cause injury.
FEED THE WORKPIECE AGAINST THE DIRECTION OF
THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE
SURFACE. Feeding it from the other direction will cause
the workpiece to be thrown out at high speed.
DON’T FORCE THE WORKPIECE ON THE MACHINE.
Damage to the machine and/or injury may result.
DON’T OVERREACH. Loss of balance can make you
fall into a working machine, causing injury.
NEVER STAND ON THE MACHINE. Injury could occur if the
tool tips, or if you accidentally contact the cutting tool.
NEVER LEAVE THE MACHINE RUNNING UNATTENDED.
TURN THE POWER OFF. Don’t leave the machine until it
comes to a complete stop. A child or visitor could be injured.
TURN THE MACHINE “OFF”, AND DISCONNECT THE
MACHINE FROM THE POWER SOURCE before installing
or removing accessories, before adjusting or changing
set-ups, or when making repairs. An accidental start-up
can cause injury.
MAKE YOUR WORKSHOP CHILDPROOF WITH
PADLOCKS, MASTER SWITCHES, OR BY
REMOVING STARTER KEYS. The accidental start-up
of a machine by a child or visitor could cause injury.
STAY ALERT, WATCH WHAT YOU ARE DOING, AND
USE COMMON SENSE. DO NOT USE THE
MACHINE WHEN YOU ARE TIRED OR UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR MEDICATION. A moment of inattention while operating power
tools may result in injury.
TAKE PRECAUTIONS AGAINST DUST INHALATION.
The dust generated by certain woods and wood
products can be injurious to your health. Always
operate machinery in well-ventilated areas, and provide
for proper dust removal. Use wood dust collection
systems whenever possible.
ADDITIONAL SAFETY RULES FOR FOR DRILL PRESSES
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
DO NOT OPERATE THIS MACHINE until it is
completely assembled and installed according to
the instructions. A machine incorrectly assembled can
cause serious injury.
OBTAIN ADVICE from your supervisor, instructor,
or another qualified person if you are not
thoroughly familiar with the operation of this
machine. Knowledge is safety.
FOLLOW ALL WIRING CODES and recommended
electrical connections to prevent shock or electrocution.
SECURE THE MACHINE TO A SUPPORTING SURFACE. Vibration can cause the machine to slide, walk,
or tip over.
NEVER START THE MACHINE BEFORE
CLEARING THE TABLE OF ALL OBJECTS (tools,
scrap pieces, etc.). Debris can be thrown at high
speed.
NEVER START THE MACHINE with the drill bit,
cutting tool, or sanding drum against the
workpiece. Loss of control of the workpiece can
cause serious injury.
PROPERLY LOCK THE DRILL BIT, CUTTING TOOL,
OR SANDING DRUM IN THE CHUCK before
operating this machine.
REMOVE THE CHUCK KEY BEFORE STARTING
THE MACHINE. The chuck key can be thrown out
at a high speed.
TIGHTEN ALL LOCK HANDLES before starting the
machine. Loss of control of the workpiece can
cause serious injury.
USE ONLY DRILL BITS, CUTTING TOOLS,
SANDING DRUMS, OR OTHER ACCESSORIES
with shank size recommended in your instruction
manual. The wrong size accessory can cause
damage to the machine and/or serious injury.
USE ONLY DRILL BITS, CUTTING TOOLS, OR
SANDING DRUMS that are not damaged.
Damaged items can cause malfunctions that lead
to injuries.
USE RECOMMENDED SPEEDS for all operations.
Other speeds may cause the machine to
malfunction causing damage to the machine
and/or serious injury.
13.
14.
15.
16.
17.
18.
19.
20.
AVOID AWKWARD OPERATIONS AND HAND
POSITIONS. A sudden slip could cause a hand to
move into the bit.
KEEP ARMS, HANDS, AND FINGERS away from
the bit. Serious injury to the hand can occur.
HOLD THE WORKPIECE FIRMLY AGAINST THE
TABLE. Do not attempt to drill a workpiece that
does not have a flat surface against the table, or
that is not secured by a vise. Prevent the
workpiece from rotating by clamping it to the table
or by securing it against the drill press column.
Loss of control of the workpiece can cause serious
injury.
TURN THE MACHINE “OFF” AND WAIT FOR THE
DRILL BIT, CUTTING TOOL, OR SANDING DRUM
TO STOP TURNING prior to cleaning the work area,
removing debris, removing or securing work-piece,
or changing the angle of the table. A moving drill
bit, cutting tool, or sanding drum can cause
serious injury.
PROPERLY SUPPORT LONG OR WIDE workpieces. Loss of control of the workpiece can cause
severe injury.
NEVER PERFORM LAYOUT, ASSEMBLY OR
SET-UP WORK on the table/work area when the
machine is running. Serious injury can result.
TURN THE MACHINE “OFF”, disconnect the
machine from the power source, and clean the
table/work area before leaving the machine. LOCK
THE SWITCH IN THE “OFF” POSITION to
prevent unauthorized use. Someone else might
accidentally start the machine and cause serious
injury to themselves.
ADDITIONAL INFORMATION regarding the safe
and proper operation of power tools (i.e. a safety
video) is available from the Power Tool Institute,
1300 Sumner Avenue, Cleveland, OH 44115-2851
(www.powertoolinstitute.com). Information is also
available from the National Safety Council, 1121
Spring Lake Drive, Itasca, IL 60143-3201. Please
refer to the American National Standards Institute
ANSI 01.1 Safety Requirements for Woodworking
Machines and the U.S. Department of Labor OSHA
1910.213 Regulations.
SAVE THESE INSTRUCTIONS.
Refer to them often
and use them to instruct others.
4
POWER CONNECTIONS
A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should
be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the
machine to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the
same characteristics as indicated on the machine. All line connections should make good contact. Running on low
voltage will damage the machine.
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.
MOTOR SPECIFICATIONS
Your machine is wired for 120 volt, 60 HZ alternating current. Before connecting the machine to the power source,
make sure the switch is in the “OFF” position.
GROUNDING INSTRUCTIONS
THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM
ELECTRIC SHOCK.
1. All grounded, cord-connected machines:
2. Grounded, cord-connected machines intended for use
on a supply circuit having a nominal rating less than 150
volts:
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This machine is
equipped with an electric cord having an equipmentgrounding conductor and a grounding plug. The plug must
be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and
ordinances.
If the machine is intended for use on a circuit that has an
outlet that looks like the one illustrated in Fig. A, the
machine will have a grounding plug that looks like the plug
illustrated in Fig. A. A temporary adapter, which looks like
the adapter illustrated in Fig. B, may be used to connect
this plug to a matching 2-conductor receptacle as shown
in Fig. B if a properly grounded outlet is not available. The
temporary adapter should be used only until a properly
grounded outlet can be installed by a qualified electrician.
The green-colored rigid ear, lug, and the like, extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box. Whenever
the adapter is used, it must be held in place with a metal
screw.
Do not modify the plug provided - if it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding
conductor can result in risk of electric shock. The
conductor with insulation having an outer surface that is
green with or without yellow stripes is the equipmentgrounding conductor. If repair or replacement of the
electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.
NOTE: In Canada, the use of a temporary adapter is not
permitted by the Canadian Electric Code.
Check with a qualified electrician or service personnel if
t h e g ro u n d i n g i n s t r u c t i o n s a re n o t c o m p l e t e l y
understood, or if in doubt as to whether the machine is
properly grounded.
Use only 3-wire extension cords that have 3-prong
grounding type plugs and matching 3-conductor
receptacles that accept the machine’s plug, as shown in
Fig. A.
Repair or replace damaged or worn cord immediately.
GROUNDED OUTLET BOX
GROUNDED OUTLET BOX
GROUNDING
MEANS
CURRENT
CARRYING
PRONGS
ADAPTER
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
Fig. A
5
Fig. B
3. Grounded, cord-connected machines intended for
use on a supply circuit having a nominal rating between
150 - 250 volts, inclusive:
If the machine is intended for use on a circuit that has an
outlet that looks like the one illustrated in Fig. C, the
machine will have a grounding plug that looks like the
plug illustrated in Fig. C. Make sure the machine is
connected to an outlet having the same configuration as
the plug. No adapter is available or should be used with
this machine. If the machine must be re-connected for
use on a different type of electric circuit, the reconnection should be made by qualified service
personnel; and after re-connection, the machine should
comply with all local codes and ordinances.
CURRENT
CARRYING
PRONGS
GROUNDED OUTLET BOX
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
Fig. C
IN ALL CASES, MAKE CERTAIN
THE
R E C E P TA C L E I N Q U E S T I O N I S P R O P E R LY
G R O U N D E D . I F Y O U A R E N O T S U R E H AV E A
QUALIFIED ELECTRICIAN CHECK THE
RECEPTACLE.
EXTENSION CORDS
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire
extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s
plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An
undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D-1 or D-2, shows
the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge
number, the heavier the cord.
MINIMUM GAUGE EXTENSION CORD
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating
Volts
Total Length
of Cord in Feet
Gauge of
Extension Cord
Ampere
Rating
Volts
Total Length
of Cord in Feet
Gauge of
Extension Cord
0-6
0-6
0-6
0-6
120
120
120
120
up to 25
25-50
50-100
100-150
18 AWG
16 AWG
16 AWG
14 AWG
0-6
0-6
0-6
0-6
240
240
240
240
up to 50
50-100
100-200
200-300
18 AWG
16 AWG
16 AWG
14 AWG
6-10
6-10
6-10
6-10
120
120
120
120
up to 25
25-50
50-100
100-150
18 AWG
16 AWG
14 AWG
12 AWG
6-10
6-10
6-10
6-10
240
240
240
240
up to 50
50-100
100-200
200-300
18 AWG
16 AWG
14 AWG
12 AWG
10-12
10-12
10-12
10-12
120
120
120
120
up to 25
25-50
50-100
100-150
16 AWG
16 AWG
14 AWG
12 AWG
10-12
10-12
10-12
10-12
240
240
240
240
up to 50
50-100
100-200
200-300
16 AWG
16 AWG
14 AWG
12 AWG
12-16
12-16
12-16
120
120
120
up to 25
25-50
14 AWG
12 AWG
12-16
12-16
12-16
240
240
240
up to 50
50-100
14 AWG
12 AWG
GREATER THAN 50 FEET NOT RECOMMENDED
GREATER THAN 100 FEET NOT RECOMMENDED
Fig. D-2
Fig. D-1
FUNCTIONAL DESCRIPTION
FOREWORD
Delta ShopMaster DP400 is a 16½" drill press with a 120/240 V, 3/4 H.P. induction motor, a flexible work lamp and a
tilting table with c-clamp edges and diagonal slots. The Delta ShopMaster Model DP400 has a 5/8” capacity chuck and
a 3 3/8” stroke. There are 12 speed options, ranging from 250 rpm to 3000 rpm for optimum drilling performance in a
variety of materials.
6
UNPACKING AND CLEANING
Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from
all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone,
gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household
floor paste wax.
NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT
PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE
ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR
ACCESSORIES AND MAY BE INTENDED TO ILLUSTRATE TECHNIQUE ONLY.
DRILL PRESS PARTS
6
12
3
7
13
8
14
9
1
15
16
17
10
11
2
4
18
5
19
20
21
22
Fig. 2
1. Drill Press Head
13. Table Raising and Lowering Lock Lever
2. Table
14. Table Lock Lever
3. Table Bracket and Column
15. Chuck Key
4. Light
5. Base
16. M8x1.25x125mm carriage head screw, flat washer,
lockwasher, and hex nut (2 ea.) (for fastening drill
press to a supporting surface)
6. Chuck
17. M10x1.5x40mm Hex Head Screws (4)
7. Handle (3)
18. M6x1x12mm Hex Cap Head Screw (2)
8. Spindle Adapter
19. 1/4" Washer
9. Spindle Adapter Remover
20. Cord Strain Relief
10. 5mm Hex Wrench
21. Cord Clamp (2)
11. 3mm Hex Wrench
22. Cord Bushing
12. Table Raising and Lowering Handle
7
ASSEMBLY
FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE
MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION
MANUAL.
1. If your drill press is to be used in a permanent
location, the drill press base must be secured to the
supporting surface with fasteners through the two
mounting holes, (A) Fig. 3, in the drill press base.
A
IF YOU DO NOT FASTEN YOUR DRILL
PRESS IN A PERMANENT MANNER, THE DRILL
PRESS MUST BE FASTENED TO A PLYWOOD
MOUNTING BOARD TO PREVENT THE DRILL PRESS
FROM TIPPING OVER DURING NORMAL USE.
USE A GOOD GRADE OF PLYWOOD
WITH A MINIMUM 3/4" THICKNESS. DO NOT MAKE
THE MOUNTING BOARD FROM PARTICLE BOARD
SINCE PARTICLE BOARD BREAKS EASILY.
Fig. 3
28
"M
IN
IM
U
M
2. Use a plywood board base, with the minimum
dimensions as shown in Fig. 4 for mounting the drill
press base to a supporting surface.
3. Place the drill press base (D) Fig. 5, centered on the
supporting surface (E).
C
MAKE SURE THERE IS AT LEAST 3"
ON ALL FOUR SIDES OF THE BASE AS SHOWN IN
FIG. 5.
21"
MIN
IMU
M
4. Drill two 3/8" diameter holes through the holes (A)
Fig. 3 in the drill press base, and in the supporting
surface (E) Fig. 5.
Fig. 4
PLACE A PIECE OF SCRAP WOOD
UNDERNEATH THE SUPPORTING SURFACE WHEN
DRILLING THE THROUGH HOLES SO THAT THE
DRILL BIT WILL NOT DAMAGE THE MATERIAL
BENEATH THE SUPPORTING SURFACE.
3" MINIMUM
3" MINIMUM
D
5. Fasten the drill press base to the mounting board
using the carriage bolts, flat washers, lockwashers, and
hex nuts (C) Fig. 4, furnished with your drill press. The
holes for the carriage bolt heads must be countersunk
so that the bolt heads are flush or below the bottom
surface of the mounting board.
3" MINIMUM
3" MINIMUM
E
Fig. 5
THE PLYWOOD BASE MUST BE
SECURED TO THE FLOOR OR SUPPORTING
SURFACE IF THERE IS ANY TENDENCY OF THE
DRILL PRESS TO VIBRATE, SLIDE OR WALK
DURING NORMAL OPERATION.
8
6. Assemble the column (A) Fig. 6, to the base (B) using
the four M10x40mm hex head screws (C), three of which
are shown.
A
C
C
B
Fig. 6
7. Assemble table raising and lowering handle (D) Fig.
7, to worm gear shaft (E) and tighten screw (F) against
flat on shaft with 3mm wrench supplied.
F
E
D
Fig. 7
8. Thread table clamp handle (G) Fig. 8, into hole in
rear of table bracket, as shown.
G
Fig. 8
9
9. Insert table (H) Fig. 9, into hole in table bracket as
shown.
H
Fig. 9
10. Thread table locking lever (J) Fig. 10, into hole in
front of table bracket as shown.
11. Place the drill press head (K) Fig. 11, onto the
column as far as it will go. Align head (K) Fig. 12, with
table (L) Fig. 12, and base (M) Fig. 12, and tighten the
two head locking screws (N) Fig. 11 with the 5mm
wrench supplied.
J
Fig. 10
12. IMPORTANT: Make certain the tapered hole in the
bottom of spindle (T) Fig. 13, and the taper on spindle
adapter (U) are clean and free of any grease, lacquer or
rust preventive coatings. NOTE: If necessary, household
oven cleaner can effectively remove these coatings from
the spindle and spindle adapter; however, carefully follow
the manufacturer’s safety rules regarding its use.
N
K
13. Push spindle adapter (U) Fig. 13, up into spindle (T)
making certain the tang (V) engages the mating slot inside
spindle (T).
Fig. 11
K
T
V
L
U
M
Fig. 13
Fig. 12
10
14. IMPORTANT: Make certain the spindle taper (O) Fig.
14, and tapered hole in chuck (P) are clean and free of
any grease, lacquer or rust preventive coatings. NOTE:
Household oven cleaner can effectively remove any substance from the chuck; however, carefully follow the
manufacturer's safety rules concerning its use.
O
P
15. IMPORTANT: OPEN THE CHUCK JAWS AS WIDE
AS POSSIBLE MAKING SURE THE CHUCK JAWS
ARE INSIDE THE CHUCK.
Fig. 14
16. Holding chuck on taper of spindle, tap with a soft tip
hammer (Q) or a block of wood and hammer to set
chuck, as shown in Fig. 15.
To avoid damage to the chuck, NEVER
drive the chuck onto the spindle with a metal hammer.
Q
Fig. 15
17. Thread the three pinion shaft handles (R) into the
three holes located in the pinion shaft hub (S), as shown
in Fig. 16.
S
R
R
Fig. 16
11
18. Align the two holes in the lamp bracket (A) Fig. 17,
with the two holes (B) on the side of the drill press head.
A
19. Place the cord bushing (C) Fig. 17, around the top of
the lamp cord (D).
B
C
D
Fig. 17
20. Align the two holes in the lamp cord bracket (F) Fig.
18 with the two holes in the lamp bracket (A) and drill
press head.
A
F
21. Place a 1/4" washer onto a M6x1x12mm cap head
screw. Insert the screw (G) Fig. 18 through the hole in the
cord strain relief bracket and the lamp bracket and
thread the screw into the drill press head. Repeat this
process for the remaining hole in the cord strain relief
bracket and tighten both screws securely.
G
Fig. 18
22. Peel backing from cord clamp (H) Fig. 19, and apply
clamp at the location shown. Make certain the lamp
cord is routed out of the way of the drill, then secure
cord (J) to cord clamp (H) as shown in Fig. 19.
H
J
Fig. 19
12
OPERATING CONTROLS AND ADJUSTMENTS
STARTING AND STOPPING
DRILL PRESS
The switch (A) Fig. 20, is located on the front of the drill
press head. To turn the drill press “ON” move the switch
up to the “ON” position. To turn the drill press “OFF”
move the switch down to the “OFF” position.
A
Fig. 20
LOCKING SWITCH IN
THE “OFF” POSITION
IMPORTANT: When the machine is not in use, the
switch should be locked in the “OFF” position to prevent
unauthorized use. This can be done by grasping the
switch toggle (B) and pulling it out of the switch, as
shown in Fig. 21. With the switch toggle (B) removed,
the switch will not operate. However, should the switch
toggle be removed while the drill press is operating, the
switch can be turned “OFF” once, but cannot be
restarted without inserting the switch toggle (B).
B
Fig. 21
FLEXIBLE LAMP
A
The flexible lamp operates independently of the drill
press. To turn the lamp “ON” and “OFF”, rotate switch
(A) Fig. 22.
To reduce the risk of fire, use 40 watt or
less, 120 volt, reflector track type light bulb (not
supplied). A standard household light bulb should not be
used. The reflector track type light bulb should not
extend below the lamp shade.
Fig. 22
TABLE ADJUSTMENTS
G
1. The table can be raised or lowered on the drill press
column by loosening the table clamp (A) Fig. 23, and
turning the table raising and lowering handle (B). After
the table is at the desired height, tighten clamp (A) Fig.
23. NOTE: Final positioning of the drill press table
should always be from the bottom to the up position.
A
H
B
2. The table can be rotated 360 degrees by loosening
clamp (H) Fig. 23, rotate table to desired position and
tighten clamp (H).
Fig. 23
13
3. The table can be tilted right or left by pulling out and
removing table alignment pin (C) Fig. 24. NOTE: If pin (C)
is difficult to remove, turn nut (E) clockwise to pull pin
out of casting.
C
E
Fig. 24
4. Fig. 25, illustrates the table alignment pin (C)
removed. Loosen table locking bolt (D), tilt table to the
desired angle and tighten bolt (D). When returning table
to the level position, replace table alignment pin (C). This
will position the table surface at 90 degrees to the
spindle.
C
D
Fig. 25
5. A tilt scale (E) Fig. 26, is provided on the table
bracket casting to indicate the degree of tilt. A witness
line and zero mark (F) are also provided on the table to
line up with the scale (E).
E
F
Fig. 26
14
SPINDLE SPEEDS
Twelve spindle speeds are available on the drill press. Fig. 27, illustrates which steps of the pulleys the belts must be
placed to obtain the twelve speeds available.
SPINDLE
CENTER
MOTOR
540
360
250
1090
590
410
1820
1280
650
3000
2180
1450
Fig. 27
CHANGING SPEEDS AND
ADJUSTING BELT TENSION
A
E
NOTE: A BELT POSITIONING SPEED CHART (E) FIG.
28, IS LOCATED ON THE INSIDE TOP COVER OF
THE DRILL PRESS.
F
DISCONNECT MACHINE FROM POWER
SOURCE.
D
1. Lift up the belt and pulley guard (A) Fig. 28.
2. Release belt tension by loosening tension lock knob
(B) Fig. 28, and the tension knob located on the other
side of the head casting and moving tension lever (C)
forward.pivoting the motor (D) toward the front of the
drill press.
C
B
Fig. 28
3. While holding the motor toward the front of the drill
press, position the belts (F) on the desired steps of the
motor and spindle pulleys, as shown in Figs. 27 & 28.
4. After the belts are positioned on the desired steps of
the motor and spindle pulleys, move motor (D) Fig. 28,
to the rear until the belt is properly tensioned and tighten
tension lock knob (B). The belt should be just tight
enough to prevent slipping. Excessive tension will
reduce the life of the belt, pulleys and bearings. Correct
tension is obtained when the belts (F) can be flexed
about 1" out of line midway between the pulleys.
15
DRILLING HOLES TO DEPTH
Where a number of holes are to be drilled to exactly the
same depth, a depth stop is provided and is used as
follows:
B
DISCONNECT MACHINE FROM POWER
SOURCE.
D
1. Install bit in chuck.
2. Loosen lock screw (A) Fig. 29, and rotate pinion
assembly (B) until the pointer (C) lines up with the mark
on the scale (D) you wish the depth of the holes to be
drilled. Then tighten lock screw (A).
A
C
3. Place the material to be drilled on the drill press
table. Raise the drill press table until the material to be
drilled just touches the drill bit.
Fig. 29
4. Drill a test hole to check the depth and adjust if
necessary. All holes will then be drilled to the exact
depth as indicated on scale (D) Fig. 29. NOTE: Scale (D)
is calibrated in both inches and millimeters.
ADJUSTING SPINDLE
RETURN SPRING
A
E
B
The spindle is automatically returned to its upper most
position when the handle is released. It is recommended
that the handle be allowed to slowly return to the top
position after each hole has been drilled. This spring has
been properly adjusted at the factory and should not be
disturbed unless absolutely necessary. To adjust the
return spring, proceed as follows:
DISCONNECT MACHINE FROM POWER
SOURCE.
Fig. 30
1. Loosen nuts (B) and (E) Fig. 30. Make sure spring
housing (A) stays engaged with head casting.
2. While FIRMLY HOLDING spring housing (A) Fig. 31
pull out housing and rotate it until boss (D) is engaged
with the next notch in the housing. Turn the housing
counterclockwise to increase or clockwise to decrease
spring tension. Turn nut (E) until it contacts spring
housing (A), then back nut (E) out a 1/4 turn from spring
housing (A). Tighten nut (B) against nut (E), to hold the
housing in place. IMPORTANT: Inside nut (E) should
not contact spring housing (A) when tightened.
B
E
D
A
Fig. 31
16
OPERATIONS
Your drill press is to be used with drill bits with a shank of
5/8" or less in diameter. The following will give the
inexperienced operator a start on common drill press
operations. Use scrap material for practice to get a feel
of the machine before attempting regular work.
The use of accessories and attachments
not recommended by Delta may result in
risk of injury.
IMPORTANT: When the workpiece is long enough it
should always be positioned on the table with one end
against the left side of the column, as shown in Fig. 32.
This prevents the workpiece from rotating with the drill
bit or cutting tool, causing damage to the workpiece or
injury to the operator. If it is not possible to support the
workpiece against the column, the workpiece should
always be fastened to the table using clamps or a vise.
Fig. 32
INSTALLING AND
REMOVING DRILL BITS
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Insert smooth end of drill bit (A) Fig. 33, into chuck
(B), as far as it will go, and then back the bit out 1/16",
or up to the flutes for small bits.
D
2. Make certain that the drill bit (A) Fig. 33, is centered
in the chuck (B) before tightening the chuck with the key
(C).
B
3. Turn the chuck key (C) Fig. 33, clockwise to tighten
and counterclockwise to loosen the chuck jaws.
C
A
4. Tighten all three chuck jaws to secure the drill bit
sufficiently so that it does not slip while drilling.
5.
MAKE SURE chuck key (C) Fig. 33, is
removed from chuck before starting drill press. Your
chuck key (C) is equipped with a self-ejecting pin (D)
which helps minimize the hazard of the key being left in
the chuck.
Fig. 33
CORRECT DRILLING SPEEDS
Factors which determine the best speed to use are: kind of material being worked, size of hole, type of drill or other
cutter, and quality of cut desired.
Use the recommended speed for the drill press bit and workpiece material.
17
BORING IN WOOD
Twist drills, although intended for metal drilling, may also be used for boring holes in wood. However, machine spur bits
are generally preferred for working in wood; they cut a flat bottom hole and are designed for removal of wood chips.
Do not use hand bits which have a screw tip; at drill press speeds they turn into the wood so rapidly as to lift the work
off the table and whirl it.
For through boring, line up the table so that the bit will enter the center hole to avoid damage to the table. Scribe a
vertical line on the front of the column and a matching mark on the table bracket and the drill press head, so that the
table and drill press head can be clamped in the center position at any height.
Feed slowly when the bit is about to cut through the wood to prevent splintering the bottom face. Use a scrap piece
of wood as a base block under the work; this helps to reduce splintering and protects the point of the bit.
DRILLING METAL
Use clamps to hold the work when drilling metal. The work should never be held in the bare hand; the drill bit may seize
the work at any time, especially when breaking through the stock. If the piece is whirled out of the operator's hand, the
operator may be injured. The drill bit will be broken if the work strikes the column.
The work must be clamped firmly while drilling; any tilting, twisting or shifting results not only in a rough hole, but also
increases drill bit breakage. For flat work, lay the piece on a wooden base and clamp it firmly down against the table
to prevent it from turning. If the piece is of irregular shape and cannot be laid flat on the table, it should be securely
blocked and clamped.
MAINTENANCE
REMOVING SPINDLE ADAPTER
The spindle adapter and chuck can be removed for the
purpose of using shanks with a #2 morse taper.
B
A
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Align the slot in the quill (A) Fig. 34, with the slot in the
spindle (B).
Fig. 34
C
2. Insert the spindle adapter remover (C) Fig. 35,
through the slot in the quill and the slot in the spindle.
3. Tap the spindle adapter remover (C) Fig. 35, with a
hammer until the the spindle adapter and chuck fall out
from the quill.
Fig. 35
18
NOTES
19
ACCESSORIES
A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers,
and Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or
for the name of your nearest supplier.
Since accessories other than those offered by Delta have not been tested with this
product, use of such accessories could be hazardous. For safest operation, only Delta
recommended accessories should be used with this product.
PARTS, SERVICE OR WARRANTY ASSISTANCE
All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network
of Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional
information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location
of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).
Two Year Limited New Product Warranty
Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory
which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product
prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two
years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. For all refurbished Delta
product, the warranty period is 180 days. Delta may require that electric motors be returned prepaid to a motor
manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible for any asserted
defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by
anyone other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for
incidental or consequential damages resulting from defective products. This warranty is Delta’s sole warranty and sets
forth the customer’s exclusive remedy, with respect to defective products; all other warranties, express or implied, whether
of merchantability, fitness for purpose, or otherwise, are expressly disclaimed by Delta.
20
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable • Delta Machinery are Available at These Locations
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta)
ARIZONA
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: (602) 437-1200
Fax: (602) 437-2200
CALIFORNIA
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
GEORGIA
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
San Diego 92111
7638 Clairemnot Blvd.
Phone: (858) 277-9595
Fax: (858) 277-9696
ILLINOIS
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
COLORADO
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
MARYLAND
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
FLORIDA
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
MASSACHUSETTS
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
MINNESOTA
Minneapolis 55429
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
MISSOURI
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
St. Louis 63119
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
NEW YORK
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
OHIO
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
OREGON
Portland 97230
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
PENNSYLVANIA
Willow Grove 19090
(Philadelphia)
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
TEXAS
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Houston 77043
4321 Sam Houston Parkway,
West
Suite 180
Phone: (713) 983-9910
Fax: (713) 983-6645
WASHINGTON
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
Authorized Service Stations are located in many large cities. Telephone 800-438-2486 or 731-541-6042 for assistance locating one.
Parts and accessories for Porter-Cable·Delta products should be obtained by contacting any Porter-Cable·Delta Distributor, Authorized
Service Center, or Porter-Cable·Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will
be directed to the nearest Porter-Cable·Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas
grandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios
para los productos Porter-Cable·Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable·Delta, Centro
de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable·Delta. Si no tiene acceso a ninguna de estas opciones, llame al
800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable·Delta más cercano.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
ALBERTA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: (403) 735-6166
Fax: (403) 735-6144
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
MANITOBA
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: (204) 633-9259
Fax: (204) 632-1976
ONTARIO
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 767-4132
Fax: (519) 767-4131
QUÉBEC
1515 ave.
St-Jean Baptiste, Suite 160
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
1447, Begin
St-Laurent, (Montréal),
Québec
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques
suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®,
Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®,
Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, MIDI LATHE®,
MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®&(design), PORTERCABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-3®&(design), QUICKSAND®&(design),
QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAW
BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design), The Lumber
Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®,
TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®,
Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®, WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las
Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar
registradas en otros países.
Printed in U.S.A.
PC-0104-149
Download PDF

advertising