Eldes | EPGM8 | User manual | Eldes EPGM8 User manual

PGM OUTPUT EXPANSION MODULE
EPGM8
EPGM1 is a PGM output expansion module intended for using with ELDES alarm systems. This module allows to connect up to
additional 8 electrical appliances.
Main EPGM8 features:
• PGM output expansion adding 8 additional PGM outputs
• compatible with ESIM264 / ESIM364
1. Package Content
1. EPGM8......................................................................qty. 1
2. EPGM8 User Manual... .......................................qty. 1
2. Technical Specifications
2.1 Electrical & Mechanical Characteristics
Power Supply
10-24V
Number of PGM Outputs
8
PGM Output D1-D8 Circuit
100mA max
1R
OUT
Open collector output.
Output is pulled to COM when
turned on.
Maximum Commuting PGM Output Values
Voltage – 30V; current 500mA
Dimensions
40 x 55 x 15 mm
Range of Operating Temperatures
-20...+55ºC
2.2 Connector Functionality
PGM outputs
12V
Positive power supply contact
GND
Negative power supply contact
12V GND
D1 - D8
Fig. No. 1
2
D1 D2 D3 D4 D5 D6 D7 D8
3. Installation
1. Disconnect ELDES alarm system main power supply and backup battery.
2. Insert EPGM8 pins to appropriate ELDES alarm system slots (see Fig. No. 2)
STATUS
PWR
Z6
Z5
Z4
Z3
Z2
Z1
C1
C2
NETWORK
C4
C3
ANTENNA
SMA
SIM
CARD
3A
EPGM8
USB
D1 D2 D3 D4 D5 D6 D7 D8
12V GND
ESIM264
PRG
FUSE
DEF
AKU+
AKU-
AC/DC
AC/DC
AUX+
AUXBELL+
BELLCOM
G
Y
C2
C1
BUZ+
BUZMIC+
MIC+5V
DATA
COM
Z6
COM
Z5
Z4
COM
Z3
Z2
COM
Z1
Fig. No. 2
3. Connect EPGM8 12V positive power supply contact with ELDES alarm system AUX+ contact and EPGM8 GND contact with
ELDES alarm system AUX- contact. (see Fig. No. 3).
4. Connect the electrical appliances to D1 – D8 PGM outputs. (see Fig. No. 3)
ESIM264
EPGM8
12V GND
AUX- AUX+
D1 D2 D3 D4 D5 D6 D7 D8
El. Appliance 1
TO AUX+
El. Appliance 2
TO AUX+
El. Appliance 3
TO AUX+
El. Appliance 4
TO AUX+
El. Appliance 5
TO AUX+
El. Appliance 6
TO AUX+
El. Appliance 7
TO AUX+
El. Appliance 8
TO AUX+
Fig. No. 3
5. Power up ELDES alarm system.
6. Enable EPGM8 mode using EKB2, EKB3 keyboards or ELDES Configuration Tool software. For more details, please, refer to
software’s HELP section or see ELDES alarm system installation manual.
7. EPGM8 is ready for use with ELDES alarm system.
USER MANUAL EPGM8 V1.0
3
4. Additional Information
Limited Liability
The buyer must agree that the system will reduce the risk of fire, theft, burglary or other dangers but does not guarantee against
such events.“ELDES UAB” will not take any responsibility regarding personal or property or revenue loss while using the system.
“ELDES UAB” liability according to local laws does not exceed value of the purchased system. “ELDES UAB” is not affiliated with any
of the Internet providers therefore is not responsible for the quality of Internet service.
Manufacturer Warranty
This device carries a 24-month warranty by the manufacturer “ELDES UAB”. Warranty period starts from the day the system has
been purchased by the end user. The warranty is valid only if the system has been used as intended, following all guidelines listed
in the manual and within specified operating conditions. Receipt must be kept as a proof of purchase date. The warranty is voided
if the system has been exposed to mechanical impact, chemicals, high humidity, fluids, corrosive and hazardous environment or
other force majeure factors.
Safety instructions
Please read and follow these safety guidelines in order to maintain safety of operators and people around:
• DO NOT use the system where it can be interfere with other devices and cause any potential danger.
• DO NOT use the system with medical devices.
• DO NOT use the system in hazardous environment.
• DO NOT expose the system to high humidity, chemical environment or mechanical impacts.
• DO NOT attempt to personally repair the system.
EPGM8 must be powered by 10-24V
100mA max. DC power supply which must be approved by LST EN 60950-1 standard
and be easily accessible nearby the device. When connecting the power supply to EPGM8, switching the pole terminals places
is forbidden.
Any additional devices linked to EPGM8 (electrical appliances, relays etc.) must be approved by LST EN 60950-1 standard.
Main power and backup battery of ELDES alarm system must be disconnected before any installation or tuning work starts. The
system installation or maintenance must not be done during stormy conditions.
EPGM8 is fully turned off by disconnecting 2-pole switch device of the external power supply or any other linked
device that EPGM8 is powered from.
The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that
the product must not be disposed of together with household waste. To prevent possible harm to human health and/or the
environment, the product must be disposed on in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the system supplier, or the local authority responsible for waste
disposal in your area.
Copyright © “ELDES UAB”, 2011. All rights reserved
It is not allowed to copy and distribute information in this document or pass to a third party without advanced written authorization
by “ELDES UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without a warning. Hereby,
„ELDES UAB“ declares that this PGM output expansion module EPGM8 is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at www.eldes.lt
4
USER MANUAL EPGM8 V1.0
5
Made in Lithuania.
www.eldes.lt

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project