Installation manual | Delta 40-650 Type 2 Cordless Saw User Manual

GAS LOG VENTED DECORATIVE APPLIANCE
OWNER'S OPERATION AND INSTALLATION MANUAL
ANSI Z21.84
O-TL REPORT # 114-L-31-4
BVSR18, BVSR24, BVDR18, BVDR24, BVDR30
For Use with Log Sets:
American Pepper Log Models BAP18 and BAP24
Ponderosa Pine Log Models BOP18 and BOP24
Mossy Maple BMM18, BMM24 (Shown) and BMM30
Texas Mesquite Log Models BTM18, BTM24 and BTM30
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
— Do not store or use gasoline or other ­flammable vapors
and liquids in the v
­ icinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
— Installation and service must be performed by a qualified installer, service agency or the gas supplier.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
For more information, visit www.desatech.com
Table of Contents
Safety................................................................... 2
Product Identification............................................ 4
Local Codes......................................................... 4
Unpacking............................................................ 4
Optional Product Features................................... 4
Installation ........................................................... 5
Operation............................................................ 13
Inspecting Burners ............................................ 15
Cleaning and Maintenance................................. 15
Troubleshooting.................................................. 16
Replacement Parts............................................. 19
Accessories........................................................ 19
Parts................................................................... 20
Warranty...............................................Back Cover
Safety
WARNING: Improper installation, adjustment, alteration,
service or maintenance can
cause injury or property damage.
Refer to this manual for correct
installation and operational
procedures. For assistance or
additional information consult
a qualified installer, service
agency or the gas supplier.
WARNING: This appliance
is for installation only in a
solid-fuel burning masonry or
UL127 factory-built fireplace,
constructed of noncombustible
material and connected to a
working flue. (See page 5 for
minimum flue opening.)
WARNING: This is a gas-fired
appliance. It uses air (oxygen)
from the room in which it is installed. Provisions for adequate
combustion and ventilation air
must be provided. Refer to the
National Fuel Gas Codes, ANSI
Z233.1/NFPA 54, Air for Combustion and Ventilation.
This appliance may be installed
in an aftermarket,* permanently
located, manufactured (mobile)
home, where not prohibited by
local codes.
* Aftermarket: Completion of sale, not for
purpose of resale, from the manufacturer.
2
WARNING: This product contains and/or generates chemicals
known to the State of California
to cause cancer or birth defects
or other reproductive harm.
WARNING: Keep flue open
when operating unit.
IMPORTANT: Read this owner’s
manual carefully and completely
before trying to assemble, operate or service this log set.
Improper use of this log set can
cause serious injury or death
from burns, fire, explosion,
electrical shock and carbon
monoxide poisoning.
DANGER: Carbon monoxide
poisoning may lead to death!
Carbon Monoxide Poisoning: Early signs
of carbon monoxide poisoning resemble the
flu, with headaches, dizziness or nausea. If
you have these signs, the log set may not be
working properly. Get fresh air at once! Have
log set serviced. Some people are more affected by carbon monoxide than others. These
include pregnant women, people with heart or
lung disease or anemia, those under the influence of alcohol and those at high altitudes.
Natural Gas: Natural gas is odorless. An
odor-making agent is added to the gas. The
odor helps you detect a gas leak. However,
the odor added to the gas can fade. Gas may
be present even though no odor exists.
Make certain you read and understand all
warnings. Keep this manual for reference. It
is your guide to safe and proper operation of
this log set.
www.desatech.com
901746-01E
safety
Continued
WARNING: Any change to
this log set or its controls can
be dangerous.
1. This appliance, as supplied, is only for
use with the type of gas indicated on the
rating plate. This appliance is convertible for use with propane/LP, using the
GA9050A-1 or GA9150A pilot kit.
2. If you smell gas
•shut off gas supply
•do not try to light any appliance
•do not touch any electrical switch; do not
use any phone in your building
•immediately call your gas supplier from
a neighbor’s phone. Follow the gas supplier’s instructions
•if you cannot reach your gas supplier,
call the fire department
3. Never install the log set
•in a recreational vehicle
•where curtains, furniture, clothing or other
flammable objects are less than 42" from
the front, top or sides of the log set
•in high traffic areas
•in windy or drafty areas
4. Before installing in a solid fuel burning
fireplace, the chimney flue and firebox
must be cleaned of soot, creosote, ashes
and loose paint by a qualified chimney
cleaner. Creosote will ignite if highly
heated. Inspect chimney flue and firebox
for damage. If damaged, repair flue before
operating heater.
5. You must operate this log set with a fireplace screen in place. Make sure fireplace
screen is closed before running log set.
6. This log set is designed to be smokeless.
If logs ever appear to smoke, turn off appliance and call a qualified service person.
Note: During initial operation, slight smoking could occur due to log curing and
the burning of manufacturing residues.
You may wish to add more ventilation by
opening a window.
7. To reduce the creation of soot, follow the
instructions in Cleaning and Maintenance,
page 11.
901746-01E
8. Do not allow fans to blow directly into the
fireplace. Avoid any drafts that alter burner
flame patterns. Ceiling fans can create
drafts that alter burner flame patterns.
Altered burner patterns can increase
sooting.
9. Do not use a blower insert, heat exchanger insert or other accessory not approved
for use with this log set.
10.This installation and provisions for combustion and ventilation air must conform
to the National Fuel Gas Code, ANSI
Z233.1/NFPA 54, Air for Combustion and
Ventilation.
11.Do not run log set
•where flammable liquids or vapors are
used or stored
•under dusty conditions
12.Do not burn solid fuel in the fireplace after
installing the log set. Do not use this log
set to cook food or burn paper or other
objects.
13.Log set becomes very hot when in use.
Keep children and adults away from hot
surface to avoid burns or clothing ignition.
Log set will remain hot for a time after
shutdown. Allow surface to cool before
touching.
14.Carefully supervise young children when
they are in the room with log set.
15.Do not use appliance if any part has been
exposed to or under water. Immediately
call a qualified service technician to inspect the room appliance and to replace
any part of the control system (if using
GA9050A-1 or GA9150A) and any gas
control which has been under water.
16.To help prevent breakage, new logs must
be broken-in (see Curing Logs, page 13).
17.Turn log set off and let cool before servicing, installing or repairing. Only a qualified
service person should install, service or
repair log set.
18.Provide adequate clearances around air
openings.
19 Control knob may be hot when turning
unit off. A 6" extension rod is available to
make he knob more easily accessible and
reduce temperature of control knob (see
Accessories on page 19).
www.desatech.com
3
Product Identification
Grate Steps
Grate
Hearth Kit Model______________________
Serial Number________________________
Burner Pan
Log Set Model________________________
Burner Clamp
Burner Manifold
Figure 1 - Product Identification (BVDR24 Shown)
Unpacking
Local Codes
Install and use log set with care. Follow all
local codes. In the absence of local codes,
use the latest edition of The National Fuel
Gas Code ANSI Z223.1/NFPA 54*.
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
CAUTION: Do not remove
the data plates from the burner
pan. The data plates contain
important warranty and safety
information.
1. Remove logs, hearth kit, pan materials
and hardware from carton.
2. Remove all protective packaging applied
to logs and base for shipment.
3. Check heater for any shipping damage.
If heater is damaged call DESA Heating,
LLC at 1-866-672-6040 for replacement
parts before returning to dealer.
Optional Product Features
ON/OFF Safety Valve/Pilot kit
and Propane/lp conversion
An optional valve/safety pilot kit with a piezo
ignitor is available for this appliance. This system requires no matches, batteries or other
sources to light. You must use this optional
system for LP conversion. See Accessories,
page 19.
remote control ready
(Millivolt) Safety Valve/Pilot kit
Remote Control Accessories
There is an optional hand-held ON/OFF remote control that can be purchased separately
for this log set. You must use the millivolt
valve/safety pilot kit to use remote accessories with this appliance. See Accessories,
page 19.
A wall switch is also available for this appliance. You must use the millivolt valve/safety
pilot kit to use the wall switch with this appliance. See Accessories, page 19.
An optional millivolt valve/safety pilot kit with
a piezo ignitor is available for this appliance.
This system requires no matches, batteries
or other sources to light. This system may
be connected to a wall switch or hand-held
wireless remote control. See Accessories,
page 19.
4
www.desatech.com
901746-01E
Installation
WARNING: The Massachusetts State Board requires all
installations be performed by
a Licensed Plumber or Gas Fitter. Massachusetts state code
requires all vent dampers be
welded open or removed.
CAUTION: Do not remove
the data plates attached to the
burner pan. The data plates
contain important warranty and
safety information.
WARNING: Before installing
in a solid fuel burning fireplace,
the chimney flue and firebox
must be cleaned of soot, creosote, ashes and loose paint by
a qualified chimney cleaner.
Creosote will ignite if highly
heated. A dirty chimney flue may
create and distribute soot within
the house. Inspect chimney flue
for damage.
901746-01E
NOTICE: Installation, service,
and repair of this appliance must
be performed by a qualified installer, service agency, company
or gas supplier experienced with
this type of gas appliance. Only
factory authorized components
listed in these instructions may
be used in accordance with the
manufacturer’s instructions and
all codes and requirements of
the authority having jurisdiction. Any modifications to this
kit, or use of unauthorized
components or accessory items
will void the manufacturer’s
warranty, and may result in a
hazardous condition.
FLUE OPENING SPECIFICATIONS
Note: This vented appliance must be installed
only in a solid-fuel burning fireplace with a
working flue and constructed of noncombustible material.
The charts in Figure 2, page 6, indicate technical information regarding the installation of
your gas log set. Please make sure that all of
the specifications shown are applicable before
installation is attempted.
The fireplace must include a working flue and
venting system with minimum openings
www.desatech.com
5
Installation
Continued
MODEL
DESCRIPTION
BVSR18
BVSR24
BVDR18
BVDR24
BVDR30
18" Single Burner
24" Single Burner
18" Dual Burner
24" Dual Burner
30" Dual Burner
Btu/Hr Input
Btu/Hr Input
Minimum
Natural Gas Propane/LP Gas Vent Opening
50,000
60,000
55,000
65,000
70,000
40,000
50,000
45,000
55,000
60,000
8" dia.
8" dia.
8" dia.
8" dia.
8" dia.
MINIMUM FIREBOX SIZES
MODEL
FRONT
WIDTH*
BACK
WIDTH**
DEPTH
HEIGHT
18SR/DR
24SR/DR
30DR
28"
29 3/4"
36"
16"
17"
27"
14"
15 1/2"
18"
18"
18"
18"
* Add 6" if safety valve/pilot is used.
**At depth indicated.
LOG SIZE
Burner Orifice
Natural
Propane/LP
In.
Num.
In.
Num.
18SR/DR
24SR/DR
0.120
0.129
31
30
0.073
0.086
FUEL INLET PRESSURE
SPECIFICATIONS (W.C.)
49
44
NG
LP
Min.
5.5"
11"
Max.
10.5"
13"
Figure 2 - Technical Information Charts
CHECK GAS TYPE
INSTALLING DAMPER CLAMP
Use only natural gas. If your gas supply is not
natural gas, you must install ON/OFF Safety
Valve/Pilot Kit (see Accessories, page 19).
Call dealer where you bought your log set.
If the fireplace does not have a gas supply
shutoff valve, one must be installed.
Secure damper stop clamp provided to
leading edge of damper as shown in Figure
3. If for any reason this clamp doesn't work
on your fireplace, another suitable clamp or
permanent stop must be installed, or damper
blade must be cut or removed.
VENTING SPECIFICATIONS FOR
INSTALLATION
Fireplace chimney flue and vent must be drafting properly. To check vent for proper drafting:
Light a tightly rolled newspaper on one end
and place at inside front edge of fireplace.
Observe smoke and be sure vent is properly
drawing it up the chimney. If smoke spills out
into room, extinguish flame and remove any
obstruction until proper venting is achieved.
Chimney flue damper must be fixed open to
provide a minimum of 64 sq. in. of free air
opening during operation of this log set. A
multipurpose damper clamp is provided to fix
the damper in position.
6
Damper
Clamp
Damper
Damper
Clamp
Damper
Masonry Fireplace
Damper
Manufactured Fireplace
Figure 3 - Attaching Damper Clamp
www.desatech.com
901746-01E
Installation
Continued
CONNECTING TO GAS SUPPLY
WARNING: A qualified service person must connect log
set to gas supply. Follow all
local codes.
Installation Items Needed
Before installing log set, make sure you have
the items listed below.
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve
• test gauge connection
• adjustable (crescent) wrench or pliers
• sediment trap
• tee joint
• pipe wrench
CAUTION: Use only new,
black iron or steel pipe. Internally-tinned copper tubing may
be used in certain areas. Check
your local codes. Use pipe of
1/2" diameter or greater to allow
proper gas volume to log set. If
pipe is too small, undue loss of
volume will occur.
Installation must include an equipment shutoff
valve, union, and a plugged 1/8" NPT tap.
Locate NPT tap within reach for test gauge
hook up. NPT tap must be upstream from log
set (see Figure 4).
IMPORTANT: Install equipment shutoff valve
in an accessible location. The equipment
shutoff valve is for turning on or shutting off
gas to appliance.
Apply pipe joint sealant lightly to male NPT
threads. This will prevent excess sealant from
going into pipe. Excess sealant in pipe could
result in a clogged burner injector.
901746-01E
WARNING: Use pipe joint
sealant that is resistant to liquid
petroleum (LP) gas.
We recommend that you install a sediment
trap in the supply line as shown in Figure 4.
Locate sediment trap where it is within reach
for cleaning. Install in piping system between
fuel supply and heater. Locate sediment
trap where trapped matter is not likely to
freeze. A sediment trap traps moisture and
contaminants. This keeps them from going
into log set controls. If sediment trap is not
installed or is installed wrong, log set may
not run properly.
Approved Flexible
Gas Hose (if allowed
by local codes)
CSA Design-Certified
Equipment Shutoff Valve
With 1/8" NPT Tap*
From Gas
Meter (5"
W.C.** to
10.5" W.C.
Pressure)
3" Minimum
Tee Pipe Cap
Joint Nipple
Sediment Trap
Figure 4 - Gas Connection
* Purchase the optional CSA design-certified
equipment shutoff valve from your dealer.
** Minimum inlet pressure for purpose of input
adjustment.
www.desatech.com
7
Installation
Continued
CHECKING GAS CONNECTIONS
WARNING: Test all gas piping
and connections, internal and
external to unit, for leaks after
installing or servicing. Correct
all leaks at once.
Equipment
Shutoff
Valve
Closed
Figure 5 - Equipment Shutoff Valve
Equipment
Shutoff Valve
WARNING: Never use an
open flame to check for a leak.
Apply a noncorrosive leak detection fluid to all joints. Bubbles
forming show a leak. Correct all
leaks at once.
Pressure Testing Gas Supply
Piping System
Test Pressures In Excess Of 1/2 PSIG
(3.5 kPa)
1. Disconnect log set and its individual equipment shutoff valve from gas supply piping
system.
2. Cap off open end of gas pipe where equipment shutoff valve was connected.
3. Pressurize supply piping system by either
using compressed air or opening main gas
valve located on or near gas meter.
4. Check all joints of gas supply piping system. Apply a noncorrosive leak detection
fluid to all joints. Bubbles forming show a
leak.
5. Correct all leaks at once.
6. Reconnect log set and equipment shutoff
valve to gas supply. Check reconnected
fittings for leaks.
Test Pressures Equal To or Less Than
1/2 PSIG (3.5 kPa)
1. Close equipment shutoff valve (see
Figure 5).
2. Pressurize supply piping system by either
using compressed air or opening main gas
valve located on or near gas meter.
3. Check all joints from gas meter to equipment shutoff valve (see Figure 6). Apply
a noncorrosive leak detection fluid to all
joints. Bubbles forming show a leak.
4. Correct all leaks at once.
8
Open
Gas Meter
Figure 6 - Checking Gas Joints
Hearth kit assembly and
Installation
Kit Assembly
Note: The following instructions apply to
both standard single bar burners, as well as
dual flame “U” style burners. Be sure all pipe
threaded connections are tight, and have
thread compound to prevent leaks.
1. Determine which side the gas line will be
coming into the fireplace.
2. Using a hammer and screw driver, remove
knock-out plug from the side of the pan
that corresponds to the gas line (see
Figure 7).
3. Unscrew burner inlet fitting from burner
manifold (see Figure 8, page 9).
4. Place burner manifold in pan with threaded opening facing open knock-out plug.
Knock-out
Plugs
Figure 7 - Knock-Out Plug Locations
www.desatech.com
901746-01E
Installation
Continued
5. Using thread sealant (resistant to the action
of propane/LP gas) on larger end of fitting,
screw the burner inlet fitting through hole
and into burner manifold. Tighten using
a wrench. If using propane/LP gas, see
Propane/LP Gas Conversion, page 10.
6. Using burner clamp, screw, and nut provided, assemble clamp to pan (“U” style
burners only). This will hold the burner
manifold in place.
7. If using optional GA9050A-1 kit, go to
Optional GA9050A-1 On/Off Safety
Valve/Pilot Kit Assembly for installation
instructions. If using optional GA9150A
kit, follow instructions included with kit for
installation and operation.
Burner Clamp
Nut
Burner
Manifold
Burner Inlet
Fitting
Figure 8 - Installing Burner
Installation and Gas Connection
1. Place burner pan assembly in center of
fireplace floor. Make sure inlet end of pan
faces gas supply.
2. Thread gas supply fitting to fireplace gas
supply pipe. Use thread sealant.
3. Install adapter fitting onto burner inlet fitting using thread sealant on male threads
of burner inlet fitting (see Figure 6). Adjust
to most convenient position.
4. Install gas connector tube to gas supply
fitting. Carefully shape tube to attach to
adapter fitting. Be careful not to cause
kinks in tube.
901746-01E
Burner Pan
Assembly (Facing
Front of Fireplace)
Adaptor Fitting
Figure 9 - Installing Burner
Optional GA9050A-1 ON/
OFF Safety Valve/Pilot Kit
Assembly
For additional convenience and safety, or
for propane/LP conversion, an optional ON/
OFF safety valve/pilot kit is available. See
Accessories, page 19.
WARNING: You must use a
ON/OFF safety valve/pilot kit for
propane/LP conversion.
Burner
Pan
Screw
Gas
Connector
Tube
Natural Gas Installation
1. Thread the gas control valve onto the
burner inlet fitting (see Figure 10). Use
thread sealant on the male threads of the
burner inlet fitting. Hold the burner inlet
fitting with a wrench to prevent overtightening the connection to the burner. Make
sure the control rod is facing the front (see
Figure 10).
Gas
Control
Valve
Burner Pan
Assembly
Burner Inlet
Fitting
Control Rod
Figure 10 - Installing Gas Control Valve
www.desatech.com
9
Installation
Continued
2. Attach the pilot gas line to the pilot outlet
of the gas control valve and tighten. Connect the thermocouple to the rear of the
gas control valve. See Figure 11. Do not
overtighten. If using propane/LP gas, see
Changing Pilot Orifice, page 11.
3. Install the inlet fitting into the inlet opening of
the gas control valve (see Figure 12). Use
thread sealant on the male pipe threads.
4. Place the burner pan assembly in the
center of the fireplace floor. Make sure
the front of pan faces forward.
5. Thread the gas supply fitting to the fireplace gas supply pipe. Adjust to most
convenient position.
6. Install the gas connector tube to the gas
supply fitting. Carefully shape tube to
attach to adapter fitting. Be careful not to
cause kinks in tube.
7. Test for leaks following instructions under
Testing Burner for Leaks, page 12.
8. Retighten and adjust the location of the
gas control as necessary. The gas control
should be level, with the control rod to the
front.
Thermocouple
and Line
Pilot
and
Line
Gas Control
Valve
Figure 11 - Gas Control Valve with
Thermocouple and Pilot
Gas
Connector
Tube
Gas Inlet
Fitting
Inlet
Gas Control
Opening
Valve
Figure 12 - Installing Inlet Fitting and
Gas Connector Tube
10
9. Attach cover to burner pan using screws
provided.
10.Install thermocouple, pilot, and ignitor onto
valve cover as shown in Figure 13. Use
the provided screws.
11.Push the control rod extension onto the
“D” shaped control rod through the center
hole in the cover.
12.Install the control position decal and control knob making sure to align the marks
with the correct stop positions of the gas
control. Pilot position will allow the knob
to push in about 1/2". Align the decals in
the pilot position.
Note: Pilot valve adjustment screw may need
to be opened. See Inspecting Burners, page
15 for instructions.
Thermocouple
Screw
Ignitor
Pilot
Control
Knob
Valve Cover
Control Rod
Extension
Piezo Ignitor
Figure 13 - Installing Cover, Control
Knob and Piezo Ignitor
Propane/LP Gas Conversion
To convert to propane/LP gas, the burner inlet
fitting and pilot orifice must be replaced. The
propane/LP burner inlet fitting is supplied with
orifice installed for a 24" log set. If you have
an 18" or 30" log set, you must change this
orifice also. See Figure 1, page 4 for product
identification.
www.desatech.com
901746-01E
Installation
Continued
Burner Inlet Fitting
1. Remove burner inlet fitting from burner
pan assembly. DO NOT remove orifice
from this fitting. The propane/LP burner
inlet fitting is included in the hardware kit
(see Figure 14).
2. Be sure to use correct orifice for your appliance. The hardware kit included with
this appliance contains two orifices with
a cone-like shape. If you have an 18" set,
orifice for burner inlet fitting is red; for a 30"
set, it is black. If you have a 24" log set,
orifice is already installed inside fitting.
3. For an 18" or 30" set, use a 10 mm socket
or nut driver to remove orifice from propane/LP burner inlet fitting. Choose correct orifice for your log set size and install
in place of orifice you just removed.
4. Using thread sealant (resistant to action
of propane/LP gas) on larger end of fitting,
screw burner inlet fitting through hole
and into burner manifold, see Figure 15.
Tighten using a wrench.
5 . Follow steps 1 through 12 under Natural
Gas Installation, page 9.
Injector
for Natural
Gas
NATURAL
GAS
FITTING
Injector for
Propane/LP
Gas
PROPANE/LP
GAS FITTING
Figure 14 - Burner Inlet Fittings with
Injectors
Burner Inlet Fitting
for Natural Gas
Changing Pilot Orifice
The pilot is provided with a natural gas orifice installed. For propane/LP gas you must
remove it and replace it with an propane/LP
orifice. The hardware kit contains an propane/LP orifice with a red stripe for converting
the pilot.
1. Gently loosen and remove the pilot line connection from the bracket (see Figure 16).
2. Replace the injector with the propane/
LP pilot injector with the red stripe (see
Figure 16).
3. Replace and tighten the pilot line to the
bracket.
4. Continue with step 3 under Natural Gas
Installation, page 10.
Pilot Orifice
Figure 16 - Installing Propane/LP Pilot
Orifice
Pilot Flow Adjustment
After installation is complete and the unit has
been ignited, it may be necessary to adjust
the pilot. Use a small flat-head screwdriver to
turn the flow adjustment screw on the manual
control valve (see Figure 17). Turn the screw
counterclockwise to allow more gas to flow
or clockwise to restrict gas flow. Be careful
to limit the turns to 2 1/2 from the fully closed
position. Further turning can result in gas
leaking at the adjustment screw and the pilot
flame size will diminish. The proper pilot flow
will result in a strong blue flame between 1/2"
and 1" long.
Pilot Flow
Adjustment Screw
Figure 15 - Remove Burner Inlet FItting
Figure 17 - Piliot Flow Adjustment Screw
901746-01E
www.desatech.com
11
Installation
Continued
Testing Burner for Leaks
1. Generously apply noncorrosive leak detection fluid to all connections.
WARNING: Never check for
gas leaks with open flame.
2. Light the burner with the shutoff valve no
more than half open and holding a match
slightly in front of the pan (see Lighting
Instructions, page 13).
3. Inspect all connections for bubbles,
raw gas odor, or flame from any area
other than the burner (leaks). If leaks are
detected, shut off the gas valve immediately. Tighten, or reassemble the loose
connection(s) using pipe joint compound
until burner system is leak free.
4. When the burner is tested and leak free,
observe the individual tongues of flame
on the burner.
Note: The burner design includes more
ports on the outside of the bar. Make
sure that all ports are clear and producing flame evenly across the burner. If
any ports appear blocked, clear them by
removing the burner manifold and reaming the ports with a modified paper clip or
other suitable tool.
5. When finished testing, turn the gas shutoff valve OFF to extinguish all flames.
3. Place the back log onto the grate steps
(see Figure 19).
4. Place the front log(s) onto grate and slide
forward against the front bars of grate (see
Figure 19).
5. Place the smaller top logs onto the bottom
logs (see Figure 20, page 13). Leave as
much open space between logs as possible to minimize flame impingement and
sooting.
Note: Logs may chip if they are handled
roughly or if hit together while being
placed.
Grate Steps
Grate
Figure 18 - Installing Grate (Pan Material
Not Shown)
Back Log
Adding Pan Material
1. Open the bag of ash bed material (vermiculite) and spread it evenly across the
burner pan to the top. You may overflow
the front and sides of the pan to cover the
entire pan and connecting hardware. Do
not cover GA9050A-1 or GA9150A valve.
2. Open the glowing embers and evenly
cover the ash bed material (vermiculite)
in the burner pan.
Front Logs
Installing Grate and Logs
1. Place the grate over the burner pan where
the two outer horizontal supports on the
grate fit into the two pan positioning notches
in the rear vertical edge of the pan.
2. Slide the two rear log grate steps over the
two outer horizontal supports on the grate
as shown in Figure 18.
12
Mossy Maple
Logs Shown
Figure 19 - Installing Front and Back Logs
(Number and Style of Logs May Vary)
www.desatech.com
901746-01E
Installation
Continued
Figure 20 - Placement of Top Logs
(Mossy Maple Logs Shown)
Operation
LIGHTING
INSTRUCTIONS
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: Keep flue open
when operating unit.
WARNING: If you do not follow these instructions exactly,
a fire or explosion may result
causing property damage, personal injury or loss of life.
BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next
to the floor because some gas is heavier
than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not
use any phone in your building.
• Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier,
call the fire department.
901746-01E
1. STOP! Read safety information, above.
2. Turn the gas shutoff valve clockwise
to OFF.
3. Wait five (5) minutes to clear out any gas.
If you then smell gas STOP! Follow the
safety information column 1. If you don't
smell gas, go on to next step.
4. Light a match and lay it on top of pan
material about 2" from end of supply side
of pan
5. Slowly turn gas shutoff valve counterclockwise
to ON the position until
burner ignites. If burner doesn’t ignite
within 10 seconds with match burning,
turn shutoff valve clockwise
to OFF
and repeat steps 1 through 4 again.
GAS SHUTOFF
VALVE OPERATION
Flame Adjustment
Adjust the flame ON/OFF by turning the gas
shutoff valve counterclockwise
to open
or clockwise
to close, as necessary.
Shutting Off Appliance
Turn gas shutoff valve clockwise
the OFF position.
www.desatech.com
to
13
Operation
Continued
Pilot
Ignitor
ON
OFF
FROM "PILOT" POSITION
SLIGHT PUSH TO
TURN OFF
PULL PUSH
On
Off
ON
OFF
14
Control Knob
FROM "PILOT" POSITION
SLIGHT PUSH TO
TURN OFF
PULL PUSH
Note: Operation instructions for GA9150A
Remote Ready Valve/Pilot Kit will be included
with the kit.
1. STOP! Read the safety information,
page 13.
2. Make sure equipment shutoff valve is fully
open.
3. Press in and turn control knob clockwise
to the OFF position.
4. Wait five (5) minutes to clear out any gas.
Then smell for gas around log set and
near floor. If you smell gas, STOP! Refer
to the National Fuel Gas Codes, ANSI
Z233.1/NFPA 54, Air for Combustion and
Ventilation. If you don’t smell gas, go to
the next step.
5. Turn control knob counterclockwise
to the PILOT position and press in (see
Figure 21). Keep control knob pressed in
for five (5) seconds.
Note: You may be running this log set
for the first time after hooking up to gas
supply. If so, the control knob may need
to be pressed in for 30 seconds or more.
This will allow air to bleed from the gas
system.
•If control knob does not pop up when
released, contact a qualified service
person or gas supplier for repairs.
.
OFF
Operating instructions
FOR GA9050A-1
FROM "PILOT" POSITION
SLIGHT PUSH TO
TURN OFF
PULL PUSH
During the 2-3 hour appliance break-in period, you may detect an odor from appliance
as various paints and compounds used in
manufacturing of this log set cure. This is a
normal and temporary situation that is not
cause for alarm. However, you may want to
provide extra ventilation to the room during
this time.
To ensure proper curing of the logs:
• Ignite a 2" flame and maintain it for 1
hour.
• Burn logs in consecutive 1 hour periods
raising flame an additional 2" to full flame
height for a total of three hours.
6. With control knob pressed in, push down
and release ignitor button. This will light
pilot. The pilot is attached to the rear of
the front burner. If needed, keep pressing
ignitor button until pilot lights.
Note: If pilot does not stay lit, contact a
qualified service person or gas supplier
for repairs. Until repairs are made, light
pilot with match
7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds,
release control knob.
Note: If pilot goes out, repeat steps 3
through 7.
8. Turn control knob counterclockwise
to the ON position. Burner should
light. If burner does not light, call a qualified service person.
9. To leave pilot lit and shut off burners only,
turn control knob clockwise
to the
PILOT position.
ON
CURING
Logs
Figure 21 - Ignitor and Control Knob
Thermocouple
Pilot
Burner
Figure 22 - Thermocouple and Pilot
TO TURN OFF GAS
TO APPLIANCE
1. Turn control knob clockwise
to the
PILOT position.
2. Press in and turn control knob clockwise
to the OFF position.
3. Close equipment shutoff valve (see
Figure 5, page 8).
www.desatech.com
901746-01E
Inspecting Burners
Check pilot flame pattern and burner flame
patterns often.
PILOT Assembly
The pilot assembly is factory preset for proper
flame height. Alterations may have occurred
during shipping and handling. The pilot is
located on back right hand side of burner.
The thermocouple should be fully enveloped
in flame. Flame should not be lifting off thermocouple element.
If your pilot assembly does not meet these
requirements:
• Access pilot adjustment screw through
slot in valve cover. Turn adjustment screw
clockwise to decrease or counterclockwise
to increase flame to proper size (see Figure
17, page 11). Do not remove adjustment
screw.
• see Troubleshooting, page 16
BURNER FLAME PATTERN
Burner flames will be steady; not lifting or
floating. Flames should go up through the
middle of log set. Flames should not "spill" to
edges of pan or sides of log set.
Figure 24 shows a typical flame pattern. If
burner flame pattern differs from that described:
• turn appliance off (see To Turn Off Gas to
Appliance, page 14)
• see Troubleshooting, page 16
Thermocouple
Figure 24 - Typical Flame Pattern
Pilot
Figure 23 - Correct Pilot Flame Pattern
Cleaning and Maintenance
• Keep area around log set clean and clear
of debris.
• Occasionally, you may use a soft bristle
brush to clean logs.
• Periodically inspect air mixer and burner
tube for foreign matter blocking air inlet
and flame holes.
901746-01E
• Once every year a qualified agency or
certified chimney sweep should examine
and clean venting system of fireplace.
www.desatech.com
15
Troubleshooting
WARNING: Turn off log set and let cool before servicing. Only a
qualified service person should service and repair log set.
Note: All troubleshooting items are listed in order of operation.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Log set is smoking/sooting
excessively
(Note: It is natural and unavoidable for vented gas log
sets to produce moderate
levels of carbon (soot) where
flames contact the logs.
This is especially true with
propane/LP gas.)
1.Poor fuel quality
5.Excessive gas supply/pressure
1.Contact local natural or
propane/LP gas company
2.Adjust damper wide open
and/or have fireplace and
venting professionally
cleaned and checked
3.Separate the logs to allow
more flame passage
4.Remove any foreign items
from the flame pattern and/
or check for proper orifice
sizing
5.Preheat flue in very cold
weather
Burner is excessively noisy
(Note: The movement and
combustion of gas will create low, unavoidable levels
of noise.)
1.Passage of air/gas across
irregular surfaces
1.Relieve any tight bends or
kinks in gas supply line
Burner flame is too low or
too high
1.Incorrect gas supply or
pressure
2.Blocked burner orifice or
burner manifold ports
1.Check for proper gas supply pressure
2.Free burner orifice and
manifold ports of any burrs,
paint, or other blockage
3.Verify proper burner orifice sizing (see Figure 2,
page 6)
2.Fireplace venting system
not drafting properly
3.Excessive flame impingement or blockage
4.Improper fuel/air mixture
3.Improper burner orifice
size
When ignitor button is
pressed, there is no spark
at pilot (GA9050A-1 Only)
1.Ignitor electrode not connected to ignitor cable
2.Ignitor cable pinched or
wet
3.Bad ground on piezo ignitor
4.Broken ignitor cable
5.Bad piezo ignitor
6.Ignitor electrode broken
7.Ignitor electrode positioned
wrong
16
www.desatech.com
1.Reconnect ignitor cable
2.Free ignitor cable if pinched
by any metal or tubing.
Keep ignitor cable dry
3.Scrape away paint on bracket for better contact with
ground on piezo ignitor
4.Replace ignitor cable
5.Replace piezo ignitor
6.Replace electrode
7.Reposition electrode
901746-01E
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
When ignitor button is
pressed, there is spark at pilot
but no ignition (GA9050A-1
Only)
1.Gas supply turned off or
equipment shutoff valve
closed
2.Control knob not in PILOT
position
3.Control knob not pressed in
while in PILOT position
4.Air in gas lines when installed
1.Turn on gas supply or open
equipment shutoff valve
5.Pilot adjustment screw
closed
6.Pilot is clogged
7.Low gas pressure
Pilot lights but flame goes out
when control knob is released
(GA9050A-1 Only)
1.Control knob not fully
pressed in
2.Control knob not pressed in
long enough
3.Equipment shutoff valve not
fully open
4.Pilot flame not touching
thermocouple, which allows thermocouple to cool,
causing pilot flame to go
out. This problem could be
caused by one or both of
the following:
A) Low gas pressure
B) Dirty or partially clogged
pilot
5.Thermocouple connection
loose at control valve
6.Thermocouple damaged
7.Control valve damaged
Burner does not light after
pilot is lit (GA9050A-1 Only)
Delayed ignition burner
(GA9050A-1 Only)
6.Clean pilot (see Cleaning
and Maintenance, page 15)
or replace pilot assembly
7.Replace gas control
1.Press in control knob fully
2.After pilot lights, keep control knob pressed in 30
seconds
3.Fully open equipment shutoff valve
4.A) Contact local natural gas
company
B) Clean pilot (see Cleaning
and Maintenance, page 15)
or replace pilot assembly
5.Hand tighten until snug,
then tighten 1/4 turn more
6.Replace thermocouple
7.Replace control valve
1.Burner orifice clogged
2.Inlet gas pressure is too
low
3.Burner orifice diameter is
too small
4.Thermocouple leads disconnected or improperly
connected
1.Clean burner orifice
2.Contact local natural or
propane/LP gas company
3.Replace burner orifice
1.Pilot flame needs adjusting
1.Adjust pilot flame for approximately 2" blue flame
2.Replace pilot orifice set
2.Wrong pilot orifice
901746-01E
2.Turn control knob to PILOT
position
3.Press in control knob while
in PILOT position
4.Continue holding down control knob. Repeat igniting operation until air is removed
5.Adjust pilot flame for approximately 2" blue flame
www.desatech.com
4.Reconnect leads
17
TROUBLESHOOTING
Continued
WARNING: If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your
building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
IMPORTANT: Operating log set where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc.,
create fumes. These fumes may mix with combustion air and create odors. These odors will
disappear over time.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Log set produces a clicking/
ticking noise just after burner
is lit or shut off
1.Metal expanding while
heating or contracting while
cooling
1.This is normal with most log
sets. If noise is excessive,
contact qualified service
person
Log set produces unwanted
odors
1.Log set burning vapors from
paint, hair spray, glues,
cleaners, chemicals, new
carpet, etc. (See IMPORTANT statement above)
2.Gas leak. See Warning
statement at top of page
1.Open flue to maximum.
Stop using odor causing
products while log set is
running
1.Gas leak. See Warning
statement at top of page
1.Locate and correct all leaks
(see Checking Gas Connections, page 8)
2.Replace control valve
Gas odor even when control
knob is in OFF position
2.Control valve defective
Gas odor during combustion
18
1.Gas leak. See Warning
statement at top of page
www.desatech.com
2.Locate and correct all leaks
(see Checking Gas Connections, page 8)
1.Locate and correct all leaks
(see Checking Gas Connections, page 8)
901746-01E
Replacement Parts
Note: Use only original replacement parts.
This will protect your warranty coverage for
parts replaced under warranty.
Usually, we will ask you to return the part to
the factory.
Parts Under Warranty
Contact authorized dealers of this product. If
they can’t supply original replacement part(s),
call DESA Heating, LLC at 1-866-672-6040 for
referral information. A list of authorized dealers
can be found by visiting www.desatech.com.
When calling DESA Heating, LLC, have
ready:
• model and serial numbers of your heater
• the replacement part number
Contact authorized dealers of this product. If
they can’t supply original replacement part(s),
call DESA Heating, LLC at 1-866-672-6040.
When calling DESA Heating, LLC, have
ready:
• your name
• your address
• model and serial numbers of your heater
• how heater was malfunctioning
Parts Not Under Warranty
Accessories
Purchase these log set accessories from
your local dealer. If they can not supply these
accessories, call DESA Heating Products at
1-866-672-6040 for referral information. You
can also write to the address listed on the
back page of this manual.
Silica Sand - GA9850A
For all models. Use for firebox decoration
only.
LAVA ROCK - GA6067A
For all models. Use for firebox decoration
only.
Decorative ash bed control
cover - CDABKA
RECEIVER AND HAND-HELD
REMOTE CONTROL KIT - HRC100
Series
For all models. An attractive way to cover
control knob and piezo ignitor.
For all models. Allows the gas log set to be
turned on and off by using a hand-held remote
control. Valve/Pilot Kit GA9150A must be used
with this remote.
ON/Off safety Valve/Pilot kit
GA9050A-1
ΩPine Cones - GA9650A
For all models. Use for additional decoration only.
Ash Bed Material
(Vermiculite) GA9750A
For all models.
Glowing embers - GA9950A
For all models. Use for firebox decoration
only.
901746-01E
www.desatech.com
19
Parts
Burner Models BVSR18, BVSR24, BVDR18, BVDR24 AND BVDR30
9
9
10
7
12
5
11
5
1
6
8
4
2
13
20
3
www.desatech.com
901746-01E
PARTS
5
6
7
8
9
10
11
12
13
901056-01
901059-01
901066-01
901064-02
901064-03
901064-04
901208-01
901208-02
901209-03
901136-01
901136-02
901137-01
901137-02
901137-03
901242-01
101628-01
901430-01
901431-01
901243-01
901243-02
901246-01
901246-02
901246-03
901681-01
901078-01
901076-01
Brass 3/8 FLR x 1/2 FPT Adapter
Brass 3/8 FLR x 3/8 FPT Adapter
Brass Air Mixer - Natural Gas
Natural Gas Injector
Natural Gas Injector
Natural Gas Injector
Burner Manifold
Burner Manifold
Burner Manifold
Burner Pan
Burner Pan
Burner Pan
Burner Pan
Burner Pan
Damper Clamp - Std. Assembly
Gas Line - 10" Flex
Grate Steps
Grate Steps
Log Grate
Log Grate
Log Grate
Log Grate
Log Grate
Burner Strap
Nut #8/32
Screw #8/32 x 3/8
R24
BVD
R18
BVD
R24
BVD
R30
DESCRIPTION
BVS
1
2
3
4
BVS
KEY
NO. PART NO.
R18
This list contains replaceable parts used in your log set. When ordering parts, follow the
instructions listed under Replacement Parts on page 19 of this manual.
•
•
•
•
•
•
•
QTY.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
•
•
•
•
•
•
1
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
PARTS AVAILABLE — NOT SHOWN
901156-01 0.4# Bag Embers
901155-01 1.00# Bag Ash Bed Material (Vermiculite)
901746-01E
www.desatech.com
•
•
•
•
21
Parts
This list contains replaceable parts used in your log set. When ordering parts, follow the
instructions listed under Replacement Parts on page 19 of this manual.
8
6
7
5
4
15
9
1
3
13
14
2
1
2
3
4
5
6
7
8
9
22
901111-01
901111-02
901111-03
901711-01
901711-02
901710-01
901710-02
901710-03
901115-01
901119-01
901121-01
901120-01
901101-01
901118-01
Bottom Rear Log CS-15
Bottom Rear Log CS-20
Bottom Rear Log CS-27
Bottom Front Log VCBQ-13
Bottom Front Log VCBQ-14
Bottom Front Log VCBQ-11
Bottom Front Log VCBQ-12
Bottom Front Log VCBQ-16
Top Log VR-11
Top Log VS-12
Top Log VCR-12
Top Log VCR-11
Top Log CHR-13
Top Log VCR-9
www.desatech.com
30
24
BMM
DESCRIPTION
BMM
KEY
NO. PART NO.
BMM
18
Mossy Maple
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
901746-01E
3
7
PARTS
This list contains replaceable parts used in your log set. When ordering parts, follow the
1
instructions listed under Replacement Parts on page 19 of this manual.
2
American Pepper Log Models
Bap18 and BAP24
Ponderosa Pine Log
Models BOP18 and BOP24
6
3
10
14
11
7
5
13
4
1
9
2
8
12
1
2
12
3
4
5
6
7
8
9
10
11
12
13
14
901746-01E
901111-01
901111-02
901713-01
901713-02
901101-01
901120-01
901121-01
901103-01
901115-01
901713-01
901713-02
901111-01
901111-02
901120-01
901128-01
901127-01
901125-01
901119-01
Bottom Front Log CS-15
Bottom Front Log CS-20
Bottom Rear Log BPP-18
Bottom Rear Log BPP-24
Top Log CHR-13
Top Log VCR-11
Top Log VCR-12
Top Log CHR-13Y
Top Log VR-11
Bottom Front Log BPP-18
Bottom Front Log BPP-24
Bottom Rear Log CS-15
Bottom Rear Log CS-20
Top Log VCR-11
Top Log FS-12Y
Top Log FS-16
Top Log FS-17
Top Log VS-12
www.desatech.com
24
BOP
18
BOP
24
DESCRIPTION
BAP
KEY
NO. PART NO.
BAP
13
18
14
QTY.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
23
PARTS
This list contains replaceable parts used in your log set. When ordering parts, follow the
instructions listed under Replacement Parts on page 19 of this manual.
4
7
5
6
9
10
1
3
8
2
1
2
3
4
5
6
7
8
9
10
24
110300-01
110303-01
124205-01
110299-01
110302-01
124204-01
110298-01
110301-01
124203-01
901090-01
901119-01
901120-01
901129-01
901476-01
901844-01
901845-01
Back Log
Back Log
Back Log BFL-27
Front Right Log
Front Right Log
Front Right Log BFL-30R
Front Left Log
Front Left Log
Front Left Log BFL-30L
Top Split Log CS-16
Top Log VS-12
Top Log VCR-11
Top Log FR-12L
Top Split Log CS-13Y
Top Log FP-10Y
Top Log FP-10S
www.desatech.com
30
24
BTM
BTM
DESCRIPTION
BTM
KEY
NO. PART NO.
18
Texas Mesquite
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
901746-01E
NOTES
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
901746-01E
www.desatech.com
25
NOTES
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
26
www.desatech.com
901746-01E
NOTES
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
901746-01E
www.desatech.com
27
Warranty
KEEP THIS WARRANTY
Model (located on product or identification tag)______________________________
Serial No. (located on product or identification tag)___________________________
Date Purchased ___________________________
Keep receipt for warranty verification.
DESA HEATING, LLC LIMITED WARRANTIES
New Products
Standard Warranty: DESA Heating, LLC warrants this new product and any parts thereof to be free from
defects in material and workmanship for a period of one (1) year from the date of first purchase from an
authorized dealer provided the product has been installed, maintained and operated in accordance with
DESA Heating, LLC’s warnings and instructions.
For products purchased for commercial, industrial or rental usage, this warranty is limited to 90 days from
the date of first purchase.
Factory Reconditioned Products
Limited Warranty: DESA Heating, LLC warrants factory reconditioned products and any parts thereof
to be free from defects in material and workmanship for 30 days from the date of first purchase from an
authorized dealer provided the product has been installed, maintained and operated in accordance with
DESA Heating, LLC’s warnings and instructions.
Terms Common to All Warranties
The following terms apply to all of the above warranties:
Always specify model number and serial number when contacting the manufacturer. To make a claim under
this warranty the bill of sale or other proof of purchase must be presented.
This warranty is extended only to the original retail purchaser when purchased from an authorized dealer,
and only when installed by a qualified installer in accordance with all local codes and instructions furnished
with this product.
This warranty covers the cost of part(s) required to restore this product to proper operating condition and
an allowance for labor when provided by a DESA Heating, LLC Authorized Service Center or a provider
approved by DESA Heating, LLC. Warranty parts must be obtained through authorized dealers of this product and/or DESA Heating, LLC who will provide original factory replacement parts. Failure to use original
factory replacement parts voids this warranty.
Travel, handling, transportation, diagnostic, material, labor and incidental costs associated with warranty
repairs, unless expressly covered by this warranty, are not reimbursable under this warranty and are the
responsibility of the owner.
Excluded from this warranty are products or parts that fail or become damaged due to misuse, accidents,
improper installation, lack of proper maintenance, tampering, or alteration(s).
This is DESA Heating, LLC’s exclusive warranty, and to the full extent allowed by law; this express warranty
excludes any and all other warranties, express or implied, written or verbal and limits the duration of any
and all implied warranties, including warranties of merchantability and fitness for a particular purpose to one
(1) year on new products and 30 days on factory reconditioned products from the date of first purchase.
DESA Heating, LLC makes no other warranties regarding this product.
DESA Heating, LLC’s liability is limited to the purchase price of the product, and DESA Heating, LLC shall
not be liable for any other damages whatsoever under any circumstances including indirect, incidental, or
consequential damages.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For information about this warranty contact:
901746 01
NOT A UPC
DESA Heating, LLC
2701 Industrial Drive
Bowling Green, KY 42101
www.desatech.com
1-866-672-6040
901746-01
Rev. E
08/08
Download PDF

advertising