Denon AVR-5700 Stereo Receiver User Manual

AV SURROUND RECEIVER
AVR-5700
OPERATING INSTRUCTIONS
START
SYSTEM CALL
SET
LEARNED/TX
POWER
CALL
OFF
VDP
TUNER
1
2
3
TV/DBS
V.AUX
SHIFT
PHONO
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
CHANNEL
9
VCR-2
MASTER VOLUME
TAPE-2 MON
+10
RC-853
ON / SOURCE
DVD
TV/VCR
0
A/B
INPUT SELECTOR
VOLUME LEVEL
VOLUME
REMOTE SENSOR
L
CH INDICATOR
C
R
LOCK
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
ON / STANDBY
SL
S
SR
LFE
MASTER VOL.
ON / STANDBY
HOME
THX CINEMA
SURROUND SPEAKER
A
B
TAPE-2 MON
AUDIO
PHONO
CD
TUNER
DVD
VDP
TV / DBS
VCR-1
VCR-2
V. AUX
MD / TAPE-1
CD
DECK MD
LOCK
MUTING
TAPE-2 MON
AVR/AVC
VIDEO
DVD
TV
VDP VCR
OFF
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
TITLE
MENU/GUIDE
BAND
CH SELECT
ENTER
MODE
PHONES
DIRECT
STEREO
DOLBY / DTS
SURROUND
INPUT MODE
ANALOG
6CH
EXT. IN
INPUT
SURROUND MODE
WIDE
5CH
SCREEN
STEREO
VIDEO
SELECT
TONE
DEFEAT
BASS
CHANNEL VOLUME
SELECT
TREBLE
MEMORY
DSP
SIMULATION
SELECT
DOWN
UP
PANEL
DIMMER
MODE
SOURCE
USE/LEARN T.TONE
REC / MULTI
PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
SET UP
AVR-5700
2 We greatly appreciate your purchase of the AVR-5700.
2 To be sure you take maximum advantage of all the features the AVR-5700 has to offer, read these instructions
carefully and use the set properly. Be sure to keep this manual for future reference should any questions or
problems arise.
“SERIAL NO.
PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE
CABINET FOR FUTURE REFERENCE”
2 SAFETY PRECAUTIONS
CAUTION
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG
WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS
THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
EXPOSURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
ATTENTION
POUR PREVENIR LES CHOCS ELECTRIQUES NE PAS UTILISER CETTE
FICHE POLARISEE AVEC UN PROLONGATEUR UNE PRISE DE COURANT
OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT
ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A
DECOUVERT.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
2 NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION
• Keep the set free from moisture, water, and
dust.
• Protéger l’appareil contre l’humidité, l’eau et la
poussière.
• Do not let foreign objects in the set.
• Ne pas laisser des objets étrangers dans
l’appareil.
• Avoid high temperatures.
Allow for sufficient heat dispersion when
installed on a rack.
• Eviter des températures élevées
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une étagère.
• Unplug the power cord when not using the set
for long periods of time.
• Débrancher le cordon d’alimentation lorsque
l’appareil n’est pas utilisé pendant de longues
périodes.
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du
cordon.
2
* (For sets with ventilation holes)
• Do not obstruct the ventilation holes.
• Ne pas obstruer les trous d’aération.
• Do not let insecticides, benzene, and thinner
come in contact with the set.
• Ne pas mettre en contact des insecticides, du
benzène et un diluant avec l’appareil.
• Never disassemble or modify the set in any
way.
• Ne jamais démonter ou modifier l’appareil
d’une manière ou d’une autre.
SAFETY INSTRUCTIONS
12.
Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the
appliance.
Heed Warnings – All warnings on the appliance and in the
operating instructions should be adhered to.
14.
Cleaning – The appliance should be cleaned only as
recommended by the manufacturer.
4.
Follow Instructions – All operating and use instructions
should be followed.
15.
Power Lines – An outdoor antenna should be located away
from power lines.
5.
Water and Moisture – The appliance should not be used
near water – for example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a
swimming pool, and the like.
16.
6.
Carts and Stands – The appliance should be used only with
a cart or stand that is recommended by the manufacturer.
6A.
An appliance and cart
combination should be
moved with care.
Quick stops, excessive
force, and uneven
surfaces may cause
the appliance and cart
combination to overturn.
Outdoor Antenna Grounding – If an outside antenna is
connected to the receiver, be sure the antenna system is
grounded so as to provide some protection against voltage
surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna-discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
See Figure A.
17.
Nonuse Periods – The power cord of the appliance should
be unplugged from the outlet when left unused for a long
period of time.
1.
Read Instructions – All the safety and operating
instructions should be read before the appliance is
operated.
2.
Retain Instructions – The safety and operating instructions
should be retained for future reference.
3.
7.
Wall or Ceiling Mounting – The appliance should be
mounted to a wall or ceiling only as recommended by the
manufacturer.
18.
Object and Liquid Entry – Care should be taken so that
objects do not fall and liquids are not spilled into the
enclosure through openings.
8.
Ventilation – The appliance should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the appliance should not be
situated on a bed, sofa, rug, or similar surface that may
block the ventilation openings; or, placed in a built-in
installation, such as a bookcase or cabinet that may
impede the flow of air through the ventilation openings.
19.
9.
Heat – The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.
10.
Power Sources – The appliance should be connected to a
power supply only of the type described in the operating
instructions or as marked on the appliance.
Damage Requiring Service – The appliance should be
serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged;
or
B. Objects have fallen, or liquid has been spilled into the
appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or
exhibits a marked change in performance; or
E. The appliance has been dropped, or the enclosure
damaged.
20.
Servicing – The user should not attempt to service the
appliance beyond that described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
11.
Grounding or Polarization – Precautions should be taken so
that the grounding or polarization means of an appliance is
not defeated.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL
ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE
3
2 INTRODUCTION
Thank you for choosing the DENON AVR-5700 Digital Surround A / V receiver. This remarkable component has been engineered to provide superb surround sound
listening with home theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your favorite music sources.
As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the contents of this
manual before proceeding.
TABLE OF CONTENTS
1
Before Using ……………………………………………………………………4
10
Surround ……………………………………………………………………43~47
2
Cautions on Installation …………………………………………………………4
11
DSP Surround Simulation …………………………………………………48~51
3
Cautions on Handling ……………………………………………………………5
12
Listening to the Radio ……………………………………………………52~54
4
Features …………………………………………………………………………5
13
Last Function Memory…………………………………………………………54
5
Connections …………………………………………………………………6~13
14
Initialization of the Microprocessor …………………………………………54
6
Part Names and Functions ………………………………………………14, 15
15
Troubleshooting ………………………………………………………………55
7
Setting up the system ……………………………………………………16~27
16
Additional Information ……………………………………………………56~61
8
Remote Control Unit ………………………………………………………28~36
17
Specifications …………………………………………………………………62
9
Operation …………………………………………………………………36~42
2 ACCESSORIES
Check that the following parts are included in addition to the main unit:
Q Operating instructions…..1
W Warranty ( for North America model only )………...........1
E Service station list…….....1
R AC cord.................……1
T Remote control unit
Y R6P/AA batteries….....2
I FM indoor antenna…........1
O FM antenna adaptor….1
U AM loop antenna…...1
(RC-853)………………… ..1
1 BEFORE USING
Pay attention to the following before using this unit:
• Moving the set
To prevent short circuits or damaged wires in the connection
cords, always unplug the power cord and disconnect the
connection cords between all other audio components when
moving the set.
• Store this instructions in a safe place.
After reading, store this instructions along with the warranty in a
safe place.
• Note that the illustrations in this instructions may differ from
the actual set for explanation purposes.
• Before turning the power switch on
Check once again that all connections are proper and that there are
not problems with the connection cords. Always set the power
switch to the standby position before connecting and
disconnecting connection cords.
2 10 cm or more
2 CAUTIONS ON INSTALLATION
2
Noise or disturbance of the picture may be generated if this unit or
any other electronic equipment using microprocessors is used near a
tuner or TV.
If this happens, take the following steps:
• Install this unit as far as possible from the tuner or TV.
• Set the antenna wires from the tuner or TV away from this unit’s
power cord and input/output connection cords.
• Noise or disturbance tends to occur particularly when using indoor
antennas or 300 Ω/ohms feeder wires. We recommend using
outdoor antennas and 75 Ω/ohms coaxial cables.
For heat dispersal, leave at least 10 cm of space between the
top, back and sides of this unit and the wall or other
components.
4
2
10 cm or more
10 cm or more
Wall
3 CAUTIONS ON HANDLING
• Switching the input function when input jacks are not
connected
A clicking noise may be produced if the input function is switched
when nothing is connected to the input jacks. If this happens,
either turn down the MASTER VOLUME control or connect
components to the input jacks.
• Whenever the power switch is in the OFF state, the apparatus
is still connected on AC line voltage.
Please be sure to unplug the cord when you leave home for,
say, a vacation.
• Opening and closing the door
• Muting of PRE OUT jacks and SPEAKER terminals
The PRE OUT jacks and SPEAKER terminals include a muting
circuit. Because of this, the output signals are greatly reduced for
several seconds after the power switch is turned on or input
function, surround mode or any other-set-up is changed. If the
volume is turned up during this time, the output will be very high
after the muting circuit stops functioning. Always wait until the
muting circuit turns off before adjusting the volume.
This unit has a door on the front panel.
Lightly press on the bottom of the door to open it.
4 FEATURES
1. Digital Surround Sound Decoding
Featuring dual 32 bit high speed DSP processors, operating
entirely in digital domain, surround sound from digital sources
such as DVD, LD, DTV and satellite are faithfully re-created.
2. Dolby Digital
Using advanced digital processing algorithms, Dolby Digital
provides up to 5.1 channels of wide-range, high fidelity surround
sound. Dolby Digital is the default digital audio delivery system for
North American DVD and DTV, and is available on laser discs as
well as some digital satellite direct-to-home services.
3. DTS (Digital Theater Systems)
DTS provides up to 5.1 channels of wide-range, high fidelity
surround sound, from sources such as laser disc, DVD and
specially-encoded music discs.
4. Lucasfilm Home THX Ultra Certified
Home THX is the unique collaboration between Lucasfilm Ltd.
and audio equipment manufacturers. THX Ultra certification is the
highest performance level, and provides a rigorous set of
performance standards, along with proprietary surround sound
post-processing technologies, designed to enhance the surround
soundtrack playback experience in the home theater.
5. 24 bit D/A Conversion
All six channels, including the five main channels and the low
frequency effects (LFE) channel benefit from reference BurrBrown DACs, for optimum high fidelity reproduction of music and
movie soundtracks.
6. 24 Bit AL Processing
A feature of DENON’s premium CD players, Alpha processing is a
proprietary DSP function that provides increased definition of
detail. The latest 24 bit Alpha processing technology is applied to
the two main front channels (left and right) for superb
reproduction of high fidelity music sources.
7. Dual Surround Speaker Mode
Provides for the first time the ability to optimize surround sound
reproduction using two different types of surround sound
speakers as well as two different surround speaker positions:
(1) Movie Surround
Motion picture soundtracks use the surround channel(s) to
provide the ambient elements of the acoustic environment
they want the audience to realize. This is best accomplished
by the use of specially-designed surround speakers that offer a
wide diffusion pattern (bipolar dispersion) or by using surround
speakers that provide broad dispersion with a minimum of onaxis localization (dipolar dispersion). Side wall mounting (closer
to the ceiling) of the surround speakers provides the greatest
envelopment, minimizing localization of direct sound from the
speakers.
(2) Music Surround
With full range discrete surround channels, as well as three
discrete full range front channels, digital formats such as Dolby
and DTS offer thrilling surround sound music listening.
Producers of multi-channel discrete digital music recordings
almost always favor the use of direct radiating (monopolar)
surround speakers, placed in the rear corners of the room,
since that is how they configure their studios during the
mixing/creation process.
The DENON AVR-5700 provides the ability to connect two
different sets of surround speakers, and place them in the
appropriate locations in your home theater room, so that you
can enjoy both movie soundtracks and music listening, with
optimum results and no compromise.
8. Component Video Switching
In addition to composite video and “S” video switching, the AVR5700 provides 2 sets of component video (Y, R-Y, B-Y) inputs for
the DVD and TV/DBS inputs, and one set of component video
outputs to the television, for superior picture quality.
9. Video Select Function
Allow you to watch one source (visual) while listening to another
source (audio).
• Five Identical Power Amplifiers
Featuring discrete high current power transistors, the power
amp section is THX Ultra certified for top performance with the
widest range of speaker systems. Rated at 140 watts into 8
Ω/ohms, the amp channels feature additional low impedance
drive capability.
10.Future Sound Format Upgrade Capability via Eight Channel
Inputs & Outputs
For future multi-channel audio format(s), the AVR-5700 is provided
with 7.1 channel (seven main channels, plus one low frequency
effects channel) inputs, along with a full set of 7.1 channel preamp outputs, controlled by the 8 channel master volume control.
This assures future upgrade possibilities for any future multichannel sound format.
5
5 CONNECTIONS
• Do not plug in the AC cord until all connections have been completed.
• Be sure to connect the left and right channels properly (left with left, right with right).
• Insert the plugs securely. Incomplete connections will result in the generation of
noise.
• Use the AC OUTLETS for audio equipment only. Do not use them for hair
driers, etc.
• Note that binding pin plug cords together with AC cords or placing them near a
power transformer will result in generating hum or other noise.
• Noise or humming may be generated if a connected audio equipment is used
independently without turning the power of this unit on. If this happens, turn on the
power of the this unit.
Connecting the audio components
• When making connections, also refer to the operating instructions of the other components.
CD player
OUTPUT
R
Connecting a CD player
L
R
Pre-main (integrated) amplifier
for multi-source playback
Connect the CD player’s analog output jacks
(ANALOG OUTPUT) to this unit’s CD jacks
using pin plug cords.
DIGITAL AUDIO
L
Connecting a turntable
Connect the turntable’s output cord to the AVR5700’s PHONO jacks, the L (left) plug to the L
jack, the R (right) plug to the right jack.
Connecting the pre-out jacks
Turntable
(MM cartridge)
Use these jacks if you wish to connect external power amplifier(s) to
increase the power of the front, center and surround sound channels, or
for connection to powered loudspeakers. For instructions on using the
effect output, refer to page 41.
NOTE:
This unit cannot be used with MC cartridges
directly. Use a separate head amplifier or
step-up transformer.
If humming or other noise is
generated when the ground wire
is connected, disconnect the
ground wire.
Connecting the AC OUTLETS
AC OUTLETS
• SWITCHED
(total capacity – 120 W (1 A.))
The power to these outlets is turned on and off in conjunction with the POWER
switch on the main unit, and when the power is switched between on and
standby from the remote control unit.
No power is supplied from these outlets when this unit’s power is at standby.
Never connect equipment whose total capacity is above 120 W (1 A.)
NOTE:
Only use the AC OUTLETS for audio equipment. Never use them for hair driers,
TVs or other electrical appliances.
Ground wire
NOTE:
Refer to page 10 for notes
on the shorting pin plugs.
AC outlets (wall)
AC cord (included)
AC 120 V, 60 Hz
Extension jacks for future use
R
L
R
IN
PHONO
FM
COAX.
75
R
L
AM
Y
FRONT
MONITOR
OUT-2
CENTER
SUB
WOOFER
DVD
VDP
SURROUND
VDP
TV/
DBS
EFECT
ANTENNA TERMINALS
L
V.AUX
6CH EXT. IN
CR
Y
CB
CR
IN
TV/DBS
COMPONENT VIDEO
Y
L
OUT
L
R
FL VCR-1
VCR-1
VCR-1
VCR-2
VCR-2
SL MD/
TAPE-1
MD/
TAPE-1
L
EL TAPE-2
ER
L
OUT
VCR-1
TAPE-2
8CH EXT. IN
L
VIDEO
R
B
L
SURROUND
DOLBY DIGITAL
RF
IN
1
OPTICAL
2
3
OPTICAL-5
IN
OUT
4
IN
1
CENTER
SPEAKER SYSTEMS
COAXIAL
2
AC IN
3
SWITCHED TOTAL 120W(1A.) MAX.
AC 120V 60Hz
AC OUTLETS
VCR-2
AUDIO
R
R
IN
FRONT,CENTER / 6 16
SURROUND /
6 16
A OR B
A+B
12 16
V.AUX
C VCR-2
R
SURROUND
L
A
SPEAKER
IMPEDANCE
SW
R
R
OUT
TV/
DBS
PREOUT R
L
CB
CR
MONITOR OUT
ROOM TO ROOM
REMOTE
CONTROL
FR
SR
IN
CB
DVD
IN
R
FRONT
R
MONITOR
OUT-1
DVD
SIGNAL CD
GND
LOOP
ANT.
L
MULTI
SOURCE
OUT
S-VIDEO
DIGITAL
L
Route the connection cords, etc., in such a way that
they do not obstruct the ventilation holes.
R
L
R
L
R
L
R
L
OUTPUT
Tape deck 2
MD player, DAT deck or other component
equipped with digital input/output jacks
INPUT
OUTPUT
Connections for recording:
Connect the tape deck’s recording input jacks (LINE IN or REC) to this unit’s
tape recording (OUT) jacks using pin plug cords.
Connections for playback:
Connect the tape deck’s playback output jacks (LINE OUT or PB) to this unit’s
tape playback (IN) jacks using pin plug cords.
6
OUTPUT
INPUT
R
L
R
L
R
L
R
L
Tape deck 1 or MD
INPUT
OPTICAL
Connecting a tape deck
DIGITAL AUDIO
OPTICAL COAXIAL
CD player or other component
equipped with digital output jacks
OUTPUT
Connecting the DIGITAL jacks
Use these for connections to audio equipment with digital output.
Refer to page 25 for instructions on setting this terminal.
NOTES:
• Use 75 Ω/ohms cable pin cords for coaxial connections.
• Use optical cables for optical connections, removing the cap
before connecting.
Connecting video components
• To connect the video signal, connect using a 75 Ω/ohms video signal cable cord. Using an improper cable can result in a drop in sound quality.
• When making connections, also refer to the operating instructions of the other components.
Connecting a TV/DBS tuner
TV or DBS tuner
AUDIO
R
R
OUT
L
TV/DBS
• Connect the TV’s or DBS tuner’s video output jack (VIDEO OUTPUT) to the VIDEO (yellow) TV/DBS IN jack using a
75 Ω/ohms video coaxial pin plug cord.
• Connect the TV’s or DBS tuner’s audio output jacks (AUDIO OUTPUT) to the AUDIO TV/DBS IN jacks using pin
plug cords.
VIDEO
OUT
L
Monitor TV
VIDEO
IN
AUDIO
OUT
R
L
VIDEO
OUT
MONITOR OUT
• Connect the TV’s video input
jack (VIDEO INPUT) to the
VIDEO MONITOR OUT jack
using a 75 Ω/ohms video
coaxial pin plug cord.
• The monitor TV can also be
connected in the same way
to the VIDEO MONITOR
OUT-2 jack. Note, however,
that the AVR-5700’s onscreen display signals are
not output from this jack.
(See page 26.)
LD player, CDV player, etc.
L
R
Connecting a video disc player VDP
VDP
• Connect the video disc player’s video output jack (VIDEO OUTPUT) to the
VIDEO (yellow) VDP/DVD IN jack using a 75 Ω/ohms video coaxial pin plug
cord.
• Connect the video disc player’s analog audio output jacks (ANALOG AUDIO
OUTPUT) to the AUDIO VDP/DVD IN jacks using pin plug cords.
• A DVD player can be connected to the DVD jacks in the same way.
• It is also possible to connect a video disc player, DVD player, video camcorder,
game machine, etc., to the V.AUX jacks.
IN
PHONO
FM
COAX.
75
R
L
FRONT
MONITOR
OUT-2
CENTER
SUB
WOOFER
DVD
VDP
SURROUND
VDP
TV/
DBS
EFECT
L
AM
Note on connecting the digital input jacks
• Only audio signals are input to the digital input
jacks. For details, see page 6.
MONITOR
OUT-1
DVD
SIGNAL CD
GND
R
LOOP
ANT.
MULTI
SOURCE
OUT
IN
R
ANTENNA TERMINALS
L
R
FL VCR-1
L
L
V.AUX
OUTPUT
VCR-1
VCR-1
COAXIAL OPTICAL
VCR-2
VCR-2
OUT
6CH EXT. IN
FR
TV/
DBS
R R
PREOUT
V.AUX
R
L
LD player or other component
equipped with digital output jacks
L
SW
C VCR-2
SR
SL MD/
TAPE-1
ER
EL TAPE-2
8CH EXT. IN
R
R
OUT
L
R
L
R
IN
L
R
R
OUT
L
R
L
R
AUDIO
L
MD/
TAPE-1
R
OUT
VCR-1
L
TAPE-2
AUDIO
OUT IN
VIDEO
DOLBY DIGITAL
RF
IN
1
OPTICAL
2
3
4
OPTICAL-5
IN
OUT
IN
1
COAXIAL
2
3
VCR-2
VIDEO
S-VIDEO
DIGITAL
LD player or other component equipped
with a Dolby Digital RF output jack
AC-3RF OUT
Video deck 1
L
IN
L
Video deck 2
L
AUDIO
R
OUT IN
VIDEO
NOTES:
Video output connections for LD players equipped with AC-3RF output jacks.
• To connect an Dolby Digital AC-3 compatible LD player to the AC-3RF jacks,
connect the player’s video outputs to this unit’s VDP/DVD input jacks.
• When the AC-3RF-input selector button on the AVR-5700 is pressed, the picture
switches to the signals input to the VDP/DVD input jacks.
Connecting a video decks
• There are two sets of video deck (VCR) jacks, so two video decks can be connected for simultaneous recording or video copying.
Video input/output connections:
• Connect the video deck’s video output jack (VIDEO OUT) to the VIDEO (yellow) VCR-1 IN jack, and the video deck’s video input jack (VIDEO IN) to the VIDEO
(yellow) VCR-1 OUT jack using 75 Ω/ohms video coaxial pin plug cords.
Connecting the audio output jacks
• Connect the video deck’s audio output jacks (AUDIO OUT) to the AUDIO VCR-1 IN jacks, and the video deck’s audio input jacks (AUDIO IN) to the AUDIO VCR-1
OUT jacks using pin plug cords.
2 Connect the second video deck to the VCR-2 jacks in the same way.
7
Connecting a video component equipped with S-Video jacks
• When making connections, also refer to the operating instructions of the other components.
• A note on the S input jacks
The input selectors for the S inputs and pin jack inputs work in conjunction with each other.
• Precaution when using S-jacks
This unit’s S-jacks (input and output) and video pin jacks (input and output) have independent circuit structures, so that video signals input
from the S-jacks are only output from the S-jack outputs and video signals input from the pin jacks are only output from the pin jack outputs.
When connecting this unit with equipment that is equipped with S-jacks, keep the above point in mind and make connections according to the
equipment’s instruction manuals.
Connecting a monitor TV
MONITOR OUT
• Connect the TV’s or DBS tuner’s S video input (S-VIDEO INPUT) to the
S-VIDEO MONITOR OUT-1 jack using a S jack connection cord.
• The monitor TV can also be connected in the same way to the S-VIDEO
MONITOR OUT-2 jack. Note, however, that the AVR-5700’s on-screen
display signals are not output from this jack.
LD player, CDV player, etc.
S-VIDEO
OUT
Connecting a video disc player (VDP)
S-VIDEO
IN
Monitor TV
VDP
• Connect the video disc player’s S-Video output jack to the SVIDEO VDP IN jack using an S-Video connection cord.
• A DVD player can be connected to the DVD jacks in the same
way.
• It is also possible to connect a video disc player, DVD player,
video camcorder, game machine, etc., to the V.AUX jacks.
Connecting a TV/DBS tuner
• Connect the TV’s or DBS
tuner’s S video output jack (SVIDEO OUTPUT) to the
S-VIDEO TV/DBS IN jack using
an S jack connection cord.
S-VIDEO
OUT
TV or satellite broadcast tuner
S-VIDEO
OUT
IN
PHONO
FM
COAX.
75
R
AM
FRONT
MONITOR
OUT-2
CENTER
SUB
WOOFER
DVD
VDP
SURROUND
VDP
EFECT
TV/
DBS
TV/
DBS
V.AUX
6CH EXT. IN
PREOUT R
L
OUT
L
R
V.AUX
FR
FL VCR-1
VCR-1
VCR-1
SW
C VCR-2
VCR-2
VCR-2
SR
SL MD/
TAPE-1
MD/
TAPE-1
OUT
VCR-1
ER
EL TAPE-2
8CH EXT. IN
TAPE-2
AUDIO
Video deck 1
Connecting the video decks
IN
ANTENNA TERMINALS
IN
MONITOR
OUT-1
DVD
SIGNAL CD
GND
LOOP
ANT.
L
MULTI
SOURCE
OUT
VCR-2
VIDEO
• Connect the video deck’s S output jack (S-OUT) to the
S-VIDEO VCR-1 IN jack and the video deck’s S input jack
(S-IN) to the S-VIDEO VCR-1 OUT jack using S jack
connection cords.
• Connect the video deck’s S output jack (S-OUT) to the
S-VIDEO VCR-2 IN jack and the video deck’s S input jack
(S-IN) to the S-VIDEO VCR-2 OUT jack using S jack
connection cords.
S-VIDEO
S-VIDEO
OUT
IN
Video deck 2
Connect the components’ audio inputs and outputs as described on page 6.
NOTES:
• The on-screen display signals are not output from the video signal MONITOR OUT-2 (yellow) or S-Video signal MONITOR OUT-2 jack.
• The on-screen display signals are not output from the color difference (component) video signal MONITOR OUT jacks.
8
Connecting the antenna terminals
DIRECTION OF
BROADCASTING
STATION
AM LOOP
ANTENNA
(An Accessory)
FM ANTENNA
F-type converter plug (attached)
• When using the FM antenna
attach to this apparatus
FEEDER
CABLE
75 Ω/ohms
COAXIAL
CABLE
IN
PHONO
FM
COAX.
75
R
AM
MONITOR
OUT-2
DVD
CENTER
SUB
WOOFER
DVD
VDP
SURROUND
VDP
TV/
DBS
EFECT
V.AUX
6CH EXT. IN
300 Ω/ohms
TV/
DBS
PREOUT R
L
OUT
L
R
V.AUX
FR
FL VCR-1
VCR-1
VCR-1
SW
C VCR-2
VCR-2
VCR-2
SR
SL MD/
TAPE-1
MD/
TAPE-1
OUT
VCR-1
ER
EL TAPE-2
8CH EXT. IN
AM OUTDOOR
ANTENNA
VCR-2
TAPE-2
AUDIO
300 Ω/ohms
TERMINALS
FM ANTENNA
ADAPTER
(An Accessory)
MONITOR
OUT-1
IN
ANTENNA TERMINALS
FM INDOOR
ANTENNA
(An Accessory)
MULTI
SOURCE
OUT
FRONT
SIGNAL CD
GND
LOOP
ANT.
L
VIDEO
S-VIDEO
GROUND
• An F-type FM antenna cable plug can be connected directly.
• If the FM antenna cable’s plug is not of the F-type, connect using the
included antenna adapter.
AM loop antenna assembly
1
2
Connect to the AM
antenna terminals.
75 Ω/ohms COAXIAL CABLE
Open the cover
SHUT
3
PULL
4
Remove the vinyl tie
and take out the
connection line.
a. With the antenna
on top any stable
surface.
Mount
CLAMP
Bend in the reverse
direction.
CLAMP
mm
19
mm
14
PULL
m
9m
ANTENNA ADAPTER
mm
14
SHUT
m
5m
REMOVE
m
5m
CLAMP 3C-2V
CLAMP
5C-2V
5C-2V
75 Ω/ohms COAXIAL CABLE
b. With the antenna
attached to a wall.
Installation hole
Mount on wall, etc.
Connection of AM antennas
1. Loosen by turning 2. Insert the cord. 3. Tighten by turning
counterclockwise.
clockwise.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC which provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
Notes:
• Do not connect two FM antennas simultaneously.
• Even if an external AM antenna is used, do not disconnect
the AM loop antenna.
• Make sure AM loop antenna lead terminals do not touch
metal parts of the panel.
9
Connecting a Video Component Equipped with Color Difference (Component - Y, R-Y, B-Y) Video
Jacks (DVD Player)
• When making connections, also refer to the operating instructions of the other components.
• The signals input to the color difference (component) video jacks are not output from the VIDEO output jack (yellow) or the S-Video output
jack. In addition, the video signals input to the VIDEO input (yellow) and S-Video input jacks are not output to the color difference (component)
video jacks.
• The AVR-5700’s on-screen display signals are not output from the color difference (component) video output jacks (MONITOR OUT).
• Some video sources with component video outputs are labeled Y, Pb, Pr, or Y, Cb, Cr, or Y, R-Y, B-Y. These terms all refer to component video
color difference output.
COMPONENT
VIDEO OUT
DVD player
Connecting a DVD player
Pr
B
DVD IN jacks
• Connect the DVD player’s color difference
(component) video output jacks (COMPONENT
VIDEO OUTPUT) to the COMPONENT DVD IN jack
using 75 Ω/ohms coaxial video pin-plug cords.
• In the same way, another video source with
component video outputs such as a DTV/DBS
tuner, etc., can be connected to the TV/DBS color
difference (component) video jacks.
Y
Pb
Monitor TV
Connecting a monitor TV
MONITOR OUT jack
• Connect the TV’s color difference
(component) video input jacks
(COMPONENT VIDEO INPUT) to the
COMPONENT MONITOR OUT jack
using 75 Ω/ohms coaxial video pinplug cords.
COMPONENT
VIDEO IN
Pb
Pr
Y
• The color difference input jacks may be indicated differently on some TVs,
monitors or video components (“Pr, Pb and Y”, “R-Y, B-Y and Y”, “Cr, Cb and
Y”, etc.). For details, carefully read the operating instructions included with the
TV or other component.
• Do not connect high definition (DTV) signals to the component video input
jacks. Connect a high definition TV tuner directly to the monitor, if it is capable
of displaying HDTV signals.
R
Y
IN
CB
DVD
CR
Y
CB
CR
IN
TV/DBS
COMPONENT VIDEO
Y
FRONT
L
R
SURROUND
L
A
CB
CR
MONITOR OUT
ROOM TO ROOM
REMOTE
CONTROL
IN
OUT
SPEAKER
IMPEDANCE
FRONT CENTER / 6 16
NOTES (refer to page 6)
• Shorting pin plugs are inserted into the PHONO input jacks to prevent noise if the PHONO input is selected and there is no turntable
connected. Remove these pin plugs when connecting a turntable.
• DO NOT insert the shorting pin plugs into the REC (recording output) or pre-out jacks. Doing so may cut off the sound and may damage the
AVR-5700 and connected components.
10
Connecting the external input (EXT. IN) jacks
• These input jacks are for inputting multi-channel audio signals in high definition MUSE 3-1 format, multi-channel audio signals from an MPEG
multi-channel decoder, or future multi-channel sound format, etc.
• When making connections, also refer to the operating instructions of the other components.
IN
R
L
LOOP
ANT.
AM
Y
MONITOR
OUT-2
DVD
CENTER
SUB
WOOFER
DVD
VDP
SURROUND
VDP
TV/
DBS
EFECT
IN
CB
DVD
CR
Y
CB
CR
IN
TV/DBS
COMPONENT VIDEO
Y
IN
ANTENNA TERMINALS
V.AUX
6CH EXT. IN
R
MONITOR
OUT-1
FRONT
SIGNAL CD
GND
When connecting a high definition (MUSE 3-1
format) component, use a separately sold
mono/stereo cable if the surround channel
output is monaural.
MULTI
SOURCE
OUT
PHONO
FM
COAX.
75
TV/
DBS
PREOUT R
L
OUT
L
V.AUX
R
FR
FL VCR-1
VCR-1
VCR-1
SW
C VCR-2
VCR-2
VCR-2
SR
SL MD/
TAPE-1
MD/
TAPE-1
OUT
VCR-1
L
R
L
ER
EL TAPE-2
OPTICAL-5
IN
OUT
AUDIO
VIDEO
S-VIDEO
DIGITAL
Center
Effect, etc.
Subwoofer
Surround
4
L
R
Front
OPTICAL
2
3
1
VCR-2
TAPE-2
8CH EXT. IN
DOLBY DIGITAL
RF
IN
Decoder with 8- or 6-channel
analog output
2
For instructions on playback using the external input (EXT. IN) jacks, see page 41.
Connecting the MULTI SOURCE jacks
• If another pre-main (integrated) amplifier is connected, the multi-source jacks can be used to play a different program source in another room
at the same time. (See page 40.)
RC-616
INFRARED
RETRANSMITTER
Another room
RC-617
INFRARED SENSOR
Integrated pre-main amplifier
OUTPUT INPUT
+
R
IN
PHONO
FM
COAX.
75
R
AM
Y
FRONT
MONITOR
OUT-2
CENTER
SUB
WOOFER
DVD
VDP
SURROUND
VDP
TV/
DBS
EFECT
IN
CB
DVD
CR
Y
CB
CR
IN
TV/DBS
COMPONENT VIDEO
V.AUX
6CH EXT. IN
FL VCR-1
FR
L
OUT
L
R
VCR-1
VCR-1
C VCR-2
VCR-2
VCR-2
MD/
TAPE-1
OUT
VCR-1
VIDEO
R
B
L
SURROUND
DOLBY DIGITAL
RF
IN
1
OPTICAL
2
3
4
OPTICAL-5
IN
OUT
IN
1
CENTER
SPEAKER SYSTEMS
COAXIAL
2
S-VIDEO
AC IN
3
SWITCHED TOTAL 120W(1A.) MAX.
AC 120V 60Hz
AC OUTLETS
VCR-2
TAPE-2
AUDIO
SURROUND
L
A
IN
FRONT,CENTER / 6 16
SURROUND /
6 16
A OR B
A+B
12 16
V.AUX
SL MD/
TAPE-1
EL TAPE-2
R
SPEAKER
IMPEDANCE
SR
8CH EXT. IN
L
CB
CR
MONITOR OUT
OUT
SW
ER
Y
ROOM TO ROOM
REMOTE
CONTROL
TV/
DBS
PREOUT R
FRONT
R
MONITOR
OUT-1
IN
ANTENNA TERMINALS
AUX OUT
L
MULTI
SOURCE
OUT
DVD
SIGNAL CD
GND
LOOP
ANT.
L
+
DIGITAL
Extension jacks for future use.
2 For instructions on operations using the MULTI SOURCE jacks, see page 42 or page 40.
11
Speaker system connections
• Connect the speaker terminals with the speakers making sure that like
polarities are matched ( < with < , > with > ). Mismatching of polarities
will result in weak central sound, unclear orientation of the various
instruments, and the sense of direction of the stereo being impaired.
• When making connections, take care that none of the individual conductors
of the speaker cord come in contact with adjacent terminals, with other
speaker cord conductors, or with the rear panel.
Speaker Impedance
• Speakers with an impedance of from 6 to 16 Ω/ohms can be connected for
use as front and center speakers.
• Be careful when using two pairs of surround speakers (A + B) at the same
time, since use of speakers with an impedance of 12 to 16 Ω/ohms will lead
to damage.
• Speakers with an impedance of 6 to 16 Ω/ohms can be connected for use
as surround speakers.
• The protector circuit may be activated if the set is played for long periods of
time at high volumes when speakers with an impedance lower than the
specified impedance are connected.
NOTE:
NEVER touch the speaker terminals when the power is on.
Doing so could result in electric shocks.
Connecting the speaker cords
1. Loosen by turning
counterclockwise.
2. Insert the cord.
Connecting banana plugs
3. Tighten by turning
clockwise.
Either tightly twist or terminate the core wires.
Turn clockwise to tighten, then insert the
banana plug.
Connections
• When making connections, also refer to the operating instructions of the other components.
Connection jack for
subwoofer with built-in
amplifier (super woofer),
etc.
SURROUND SPEAKER
SYSTEMS
(L)
IN
PHONO
FM
COAX.
75
R
LOOP
ANT.
(L)
Y
MONITOR
OUT-2
DVD
CENTER
SUB
WOOFER
DVD
VDP
SURROUND
VDP
TV/
DBS
EFECT
IN
CB
DVD
CR
Y
CB
CR
IN
TV/DBS
COMPONENT VIDEO
V.AUX
6CH EXT. IN
L
OUT
L
R
FL VCR-1
VCR-1
VCR-1
VCR-2
VCR-2
SR
SL MD/
TAPE-1
MD/
TAPE-1
OUT
VCR-1
DOLBY DIGITAL
RF
IN
1
OPTICAL
2
3
4
VIDEO
S-VIDEO
OPTICAL-5
IN
OUT
IN
1
VCR-2
TAPE-2
AUDIO
SURROUND
L
A
R
B
L
SURROUND
IN
FRONT,CENTER / 6 16
SURROUND /
6 16
A OR B
A+B
12 16
V.AUX
C VCR-2
EL TAPE-2
R
SPEAKER
IMPEDANCE
SW
8CH EXT. IN
L
CB
CR
MONITOR OUT
OUT
FR
ER
Y
ROOM TO ROOM
REMOTE
CONTROL
TV/
DBS
PREOUT R
FRONT
R
MONITOR
OUT-1
IN
ANTENNA TERMINALS
12
MULTI
SOURCE
OUT
FRONT SPEAKER SYSTEMS
(R)
FRONT
SIGNAL CD
GND
AM
L
CENTER SPEAKER SYSTEM
DIGITAL
CENTER
SPEAKER SYSTEMS
COAXIAL
2
AC IN
3
SWITCHED TOTAL 120W(1A.) MAX.
AC 120V 60Hz
AC OUTLETS
(R)
• Precautions when
connecting speakers
If a speaker is placed near
a TV or video monitor, the
colors on the screen may
be disturbed by the
speaker’s magnetism. If
this should happen, move
the speaker away to a
position where it does not
have this effect.
Protector circuit
• This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the speakers under
circumstances such as when the output of the power amplifier is inadvertently short-circuited and a large current flows,
when the temperature surrounding the unit becomes unusually high, or when the unit is used at high output over a long
period which results in an extreme temperature rise.
When the protection circuit is activated, the speaker output is cut off and the power supply indicator LED flashes.
Should this occur, please follow these steps: be sure to switch off the power of this unit, check whether there are any
faults with the wiring of the speaker cables or input cables, and wait for the unit to cool down if it is very hot. Improve
the ventilation condition around the unit and switch the power back on.
If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around
the unit, switch off the power and contact a DENON service center.
Note on speaker impedance
• The protector circuit may be activated if the set is played for long periods of time at high volumes when speakers with
an impedance lower than the specified impedance (for example speakers with an impedance of lower than 4 Ω/ohms)
are connected. If the protector circuit is activated, the speaker output is cut off. Turn off the set’s power, wait for the set
to cool down, improve the ventilation around the set, then turn the power back on.
13
6 PART NAMES AND FUNCTIONS
Front Panel
• For details on the functions of these parts, refer to the pages given in parentheses ( ).
33 32 31 30 29 28 27
34
26
25
24
23
MASTER VOLUME
INPUT SELECTOR
VOLUME LEVEL
REMOTE SENSOR
L
CH INDICATOR
C
R
LOCK
ON / STANDBY
SL
S
SR
LFE
ON / STANDBY
HOME
THX CINEMA
SURROUND SPEAKER
A
B
TAPE-2 MON
PHONO
CD
TUNER
DVD
VDP
TV / DBS
VCR-1
VCR-2
V. AUX
MD / TAPE-1
TAPE-2 MON
OFF
14 15 16
PHONES
DIRECT
STEREO
DOLBY / DTS
SURROUND
INPUT MODE
ANALOG
6CH / 8CH
EXT. IN
17 18 19
SURROUND MODE
WIDE
5CH
SCREEN
STEREO
VIDEO
SELECT
TONE
DEFEAT
INPUT
1
2 3
SHIFT
DOWN
UP
PANEL
DIMMER
MODE
SOURCE
(6CH/8CH EXT. IN)…………………………………………………(41)
I VIDEO SELECT button ……………………………………………(39)
O TONE DEFEAT button ……………………………………………(39)
P PANEL button………………………………………………………(39)
{ DIMMER button……………………………………………………(39)
} REC/MULTI MODE selector button ……………………………(40)
q REC/MULTI SOURCE selector button …………………………(40)
w STEREO button ……………………………………………………(38)
e DOLBY/DTS SURROUND button ……………………………(44, 45)
r WIDE SCREEN button ……………………………………………(49)
t 5CH STEREO button ………………………………………………(49)
y DSP SIMULATION button ………………………………………(49)
BASS
TREBLE
21
22
REC / MULTI
4 5 6 7 8 9 10 11 12 13
Q Power switch ………………………………………………………(36)
W Power indicator ……………………………………………………(36)
E Headphones jack (PHONES) ……………………………………(39)
R DIRECT button ……………………………………………………(49)
T INPUT MODE selector button ……………………………………(37)
Y ANALOG button ……………………………………………………(37)
U 6CH/8CH external input button
14
20
TUNING PRESET
DSP
SIMULATION
Lightly press on the bottom
of the door to open it.
u SHIFT button …………………………………………………(53, 54)
i PRESET UP/DOWN button …………………………………(53, 54)
o BASS adjustment control …………………………………………(39)
p TREBLE adjustment control ………………………………………(39)
[ MASTER VOLUME control ………………………………………(38)
] Input source indicators
A Master volume indicator (VOLUME LEVEL) ………………………(38)
S Display
D Low frequency effect indicator (LFE) ……………………………(46)
F Digital lock indicator (LOCK)………………………………………(38)
G Dolby digital/DTS surround input channel indicators
[CH INDICATOR] …………………………………………………(45)
H Surround speaker system indicators
(SURROUND SPEAKER A/B)
J Tape 2 monitor button (TAPE-2 MON) …………………………(37)
K Input source selector dial (INPUT SELECT) ……………………(37)
L HOME THX CINEMA button ……………………………………(47)
: Remote control sensor (REMOTE SENSOR) …………………(28)
Remote control unit
• For details on the functions of these parts, refer to the pages given in parentheses ( ).
Remote control signal
transmitter………………………………(28)
LEDs (indicators) ………………………(33)
SYSTEM CALL buttons ………………(34)
START
SYSTEM CALL
SET
CALL
DVD
Input source selector
buttons …………………………………(37)
LEARNED/TX
POWER
OFF
VDP
ON / SOURCE
TUNER
1
2
3
V.AUX
PHONO
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
9
Tuner buttons …………………………(52)
CHANNEL
TAPE-2 MON
+10
Power button …………………………(36)
SHIFT
TV/DBS
VCR-2
RC-853
TV/VCR
0
A/B
System buttons ………………………(29)
VOLUME
HOME THX CINEMA button …………(47)
Surround buttons
……………………(49)
INPUT MODE selector
buttons
………………………………(37)
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
Master volume control
buttons …………………………………(38)
MASTER VOL.
AUDIO
CD
DECK MD
LOCK
MUTING
SURROUND PARAMETER
button …………………………………(49)
Mode selector switches ………………(29)
AVR/AVC
VIDEO
DVD
TV
VDP VCR
TUNING
MUTING button ………………………(39)
SYSTEM
SETUP
SURROUND
PARAMETER
TITLE
MENU/GUIDE
BAND
Channel select/enter
button …………………………………(16)
CH SELECT
Tuner system buttons
………………(29)
ENTER
MODE
Cursor buttons
………………………(16)
SELECT
MEMORY
USE/LEARN selector
button …………………………………(33)
USE/LEARN T.TONE
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
ON SCREEN button ……………………(39)
DVD SETUP button ……………………(32)
Test tone button ………………………(43)
PANEL button …………………………(39)
SYSTEM SETUP button ………………(16)
Multi source button ……………………(40)
NOTE
• The shaded buttons
do not function with the AVR-5700.
(Nothing happens when they are pressed.)
The button indicated 2, however, can be used with the learning function.
15
7 SETTING UP THE SYSTEM
• Once all connections with other AV components have been completed as described in “CONNECTIONS” (see pages 6 to 13), make the
various settings described below on the monitor screen using the AVR-5700’s on-screen display function.
These settings are required to set up the listening room’s AV system centered around the AVR-5700.
• Use the following buttons to set up the system:
SYSTEM SETUP button
Press this to display the system setup menu.
AUDIO
CD
AVR/AVC
VIDEO
DECK MD
LOCK
DVD
MUTING
SURROUND PARAMETER button
TV
VDP VCR
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
TITLE
Press this to display the surround parameter menu.
MENU/GUIDE
BAND
CH SELECT
ENTER
MODE
SELECT
MEMORY
USE/LEARN T.TONE
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
ENTER button
Press this to switch the display on the screen.
Also use this button to complete the setting on the screen.
CURSOR buttons
and
and
: Use these to move the cursors (0 and 1) to the left and right
on the screen.
: Use these to move the cursors (• and ª) up and down on the
screen.
• System setup items and default values (set upon shipment from the factory)
System setup
Speaker
Configuration
Q
(Surround
Speaker
Setting)
W
Default settings
Input the combination of speakers in your system and their
corresponding sizes (SMALL for regular speakers, LARGE for fullsize, full-range) to automatically set the composition of the signals
output from the speakers and the frequency response.
Use this function when using multiple surround speaker
combinations for more ideal surround sound. Once the
combinations of surround speakers to be used for the
different surround modes are preset, the surround
speakers are selected automatically according to the
surround mode.
Surround Sp.
Sub Woofer
Small
Small
Small
Yes
DOLBY/
DTS
SURROUND
THX
SURROUND
WIDE
SCREEN
5CH
STEREO
DSP
SIMULATION
EXT. IN
—
—
Surround
speaker
A
A
A
A
A
A
—
—
This selects the subwoofer speaker for playing deep bass signals.
E
Delay Time
This parameter is for optimizing the timing with which the audio
signals are produced from the speakers and subwoofer according to
the listening position.
R
Channel
Level
This adjusts the volume of the signals output from the speakers and
subwoofer for the different channels in order to obtain optimum
effects.
T
Subwoofer
Peak Limit
Lev
This parameter is for detecting the maximum level of the low bass
signals output from the subwoofer channel in order to protect the
subwoofer from damage and prevent unpleasant distorted sounds
from being produced.
Y
Digital Inputs
This assigns the digital input jacks for the different input
sources.
U
On Screen
Display
I
Center Sp.
Surround
mode
Bass Output
Auto Tuner
Presets
Front Sp.
Bass Out = Subwoofer Only THX
Front L & R
Center
Surround L & R
Sub Woofer
3.6 m (12 ft)
3.6 m (12 ft)
3.0 m (10 ft)
3.6 m (12 ft)
Front L
Front R
Center
Surround
L
Surround
R
Subwoofer
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
Peak Limitter = OFF
Input
source
CD
DVD
VDP
TV/DBS
VCR-1
VCR-2
V. AUX
TAPE-1
Digital
Inputs
COAXIAL
1
COAXIAL
2
COAXIAL
3
OPTICAL
1
OPTICAL
2
OPTICAL
3
OPTICAL
4
OPTICAL
5
This sets whether or not to display the on-screen display that
appears on the monitor screen when the controls on the remote
control unit or main unit are operated (from MONITOR 1 outputs
only).
FM stations are received automatically and stored in the memory.
On Screen Display = ON
A1 ~ A8
87.5/89.1/98.1/107.9/90.1/90.1/90.1/90.1 MHz
B1 ~B8
520/600/1000/1400/1500/1710 kHz/90.1/90.1 MHz
C1 ~C8
90.1 MHz
D1 ~D8
90.1 MHz
E1 ~E8
90.1 MHz
NOTES:
• The on-screen display signals are not output from the MONITOR OUT-2 output jack or the color difference (component) video signal (MONITOR OUT) jacks.
• The on-screen display signals are output with priority to the S-VIDEO MONITOR OUT jack during playback of a video component. For example, if the TV
monitor is connected to both the AVR-5700’s S-Video and video monitor output jacks and signals are input to the AVR-5700 from a video source (VDP, etc.)
connected to both the S-Video and video input jacks, the on-screen display signals are output with priority to the S-Video monitor output. If you wish to output
the signals to the video monitor output jack, do not connect a cord to the S-VIDEO MONITOR OUT jack. (For details, see page 27.)
• The AVR-5700’s on-screen display function is designed for use with high resolution monitor TVs, so it may be difficult to read small characters on TVs with
small screens or low resolutions.
• The setup menu is not displayed when headphones are being used.
16
• Speaker system layout
Basic system layout
• The following is an example of the basic layout for a system consisting of six speaker systems and a television monitor:
Center speaker system
Subwoofer
Front speaker systems
Set these at the sides of the TV or screen with
their front surfaces as flush with the front of the
screen as possible.
Surround speaker systems
With the AVR-5700 it is also possible to use the surround speaker selector function to choose the best layout for a variety of sources and
surround modes.
• Surround speaker selector function
This function uses either or both of two systems of surround speakers (A and B) to achieve the optimum sound field for different sources.
The speaker settings (on or off for A only, B only or A+B) are stored in the memory for the different surround modes and are recalled
automatically when that surround mode is set.
A
A
B
B
Using A only
A
A
B
B
Using B only
A
A
B
B
Using both A and B (A+B)
Multi surround speaker mode
17
Before setting up the system
1
2
Check that all the connections are correct, then turn on the main unit’s power.
Display the System Setup Menu.
SYSTEM
SETUP
TITLE
Setting the type of speakers
• The composition of the signals output from the different channels and the frequency response are adjusted automatically according to the
combination of speakers actually being used.
1
At the System Setup Menu select “Speaker Configuration”.
2
Switch to the speaker configuration screen.
3
ENTER
Set whether or not speakers are connected and, if so, their size
parameters.
• To select the speaker
• To select the parameter
Center Sp.
Front Sp.
Subwoofer
Surround Sp.
18
4
ENTER
Enter the setting.
a) If no surround speakers are used (if “None” is set for both A and B):
The System Setup Menu reappears.
b) If both surround speakers A and B are used (if either “Large” or “Small” is set for both A and B):
The surround speaker setting screen appears.
c) If “None” is set for surround speakers A:
“None” is automatically set for surround speakers B.
NOTE:
• Select “Large” or “Small” not according to the actual size of the speaker but according to the speaker’s capacity for playing low frequency
(approximately 80 Hz and below) signals. If you do not know, try comparing the sound at both settings (setting the volume to a level low
enough so as not to damage the speakers) to determine the proper setting.
• Parameters
Large…… Select this when using speakers that can fully reproduce low sounds of below 80 Hz.
Small…… Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient volume.
When this setting is selected, low frequencies of below 80 Hz are assigned to the subwoofer.
None…… Select this when no speakers are installed.
Yes/No… Select “Yes” when a subwoofer is installed, “No” when a subwoofer is not installed.
2 If the subwoofer has sufficient low frequency playback capacity, good sound can be achieved even when “Small” is set for the front, center
and surround speakers.
2 To take full advantage of the performance of the Home THX certified speaker systems, set the front, center and surround speaker size
parameters to “Small” and the subwoofer to “Yes”.
2 For the majority of speaker system configurations, using the SMALL setting for all five main speakers and Subwooofer On with a connected
subwoofer will yield the best results.
Selecting the surround speakers for the different surround modes
• At this screen preset the surround speakers to be used in the different surround modes.
1
When either “Large” or “Small” has been set for both speakers A and B
on the System Setup Menu (when using both A and B surround
speakers), the surround speaker setting screen appears.
Select the surround speakers to be used in the different surround modes.
• To select the surround mode
• To select the surround speaker
A:
When using surround speakers A
B:
When using surround speakers B
A+B: When using both surround speakers A and B
2
Enter the setting.
The System Setup Menu reappears.
ENTER
Speaker type setting when using both surround speakers A and B
If “Small” is set for either surround speakers A or B, the output is the same as when “Small” is set for both A and B.
2
Setting the bass output
1
At the System Setup Menu select “Bass Output”.
19
2
Switch to the Bass Output screen.
ENTER
3
4
Select the bass signal playback mode.
Enter the setting.
The System Setup Menu reappears.
ENTER
Playback modes
Subwoofer Only THX (recommended THX mode)
The LFE and the low frequencies (80 Hz or lower) of the channels set to “Small” at the Speaker Configuration screen are output from the
subwoofer.
When a channel is set to “Large”, the low frequencies are output from that channel and not from the subwoofer.
Front & Subwoofer:
Even if “Large” is set for the front speakers at the Speaker Configuration screen, the LFE and the low frequencies of the front channels as
well as the low frequencies of the other channels are output from the subwoofer. The front speakers (left and right, but not the center) also
output deep bass. This mode is provided for those with large, floor-standing tower speakers that have full range (20 Hz and up) response, and
are using a subwoofer in the system as well.
NOTE:
• To play in the Front & Subwoofer mode, set the front speakers to “Large” and the subwoofer to “Yes” at the Speaker Configuration
screen.
Setting the delay time
• Input the distance between the listening position and the different speakers to set the delay time for the surround mode.
• The delay time can be set separately for surround speakers A and B.
Preparations:
Measure the distances between the listening position and the speakers (L1 to L4 on the diagram at
the right).
L1: Distance between center speaker and listening position
L2: Distance between front speakers and listening position
L3: Distance between surround speakers and listening position
L4: Distance between subwoofer and listening position
Center
FL
L2
FR
L1
Subwoofer
Listening position
L4
L3
SL
1
20
At the System Setup Menu select “Delay Time”.
SR
2
3
Switch to the Delay Time screen.
ENTER
Select the desired unit, meters or feet.
Select (darken) the desired units, “Meters” or “Feet”.
Example: When “Feet” is selected
4
Once “Meters” or “Feet” is selected in step 3, the Delay Time screen appears automatically.
5
Select the speaker to be set.
6
Set the distance between the center speaker and listening position.
The distance changes in units of 0.1 meters (1 foot) each time the button
is pressed. Select the value closest to the measured distance.
Example: When the distance is set to 12 feet
for the center speaker (L1)
2
If “Yes” is selected for “Default”, the settings are
automatically reset to the default values.
Please note that the difference of distance for every speaker should be
15 ft (4.5 m) or less. If you set an invalid distance, a CAUTION notice,
such as screen right will appear. In this case, please relocate the blinking
speaker(s) so that its distance is no larger than the value shown in
highlighted line.
21
7
ENTER
Enter the setting.
The System Setup Menu reappears.
The AVR-5700 automatically sets the optimum surround delay time for the listening room.
NOTE:
• If the distance unit is changed after the delay time is set, the settings are reset to the factory default values (see page 16).
Setting the channel level
•
•
•
•
Use this setting to adjust so that the playback level between the different channels is equal.
From the listening position, listen to the test tones produced from the speakers to adjust the level.
The level can also be adjusted directly from the remote control unit. (For details, see page 43.)
When using both surround speakers A and B, their playback levels can be adjusted separately.
1
At the System Setup Menu select “Channel Level”.
2
Switch to the Channel Level screen.
ENTER
3
Select “Test Tone Mode”.
4
Select the mode.
Select “Auto” or “Manual”.
• Auto:
Adjust the level while listening to the test tones produced
automatically from the different speakers.
• Manual:
Select the speaker from which you want to produce the test tone to
adjust the level.
Example: When the “Auto” mode is selected
5
22
Select “Surr. Sp.”, then select the surround speaker(s) from which you want to produce the
test tone (A, B or A+B).
• Surr. Sp.: A
Adjusts the balance of the playback level between the channels when using surround
speaker A.
• Surr. Sp.: B
Adjusts the balance of the playback level between the channels when using surround
speaker B.
• Surr. Sp.: A+B
Adjusts the balance of the playback level between the channels when using surround
speakers A and B at the same time.
2 The “Surr. Sp.” can only be selected when both surround speakers A and B have been
selected at the System Setup Menu (when both A and B have been set to “Large” or
6
Select “Test Tone Start”.
7
Select “Yes”.
8
a. If the “Auto” mode is selected:
Test tones are automatically emitted from the different speakers.
The test tones are emitted from the different speakers in the
following order, at 4-second intervals the first time and second time
around, 2-second intervals the third time around and on:
1
FL
1
C
1
FR
1
SR
1
SL
1
SW
Use the CURSOR buttons to adjust all the speakers to the same
volume.
The volume can be adjusted between –12 dB and +12 dB in units of
1 dB.
Flashing
b. When the “Manual” mode is selected
Use the
and
cursor buttons to select the speaker from which
you want to produce the test tone, then use the
and
cursor
buttons to adjust so that the volume from the different speakers
sounds the same.
Example: When the volume is set to –12 dB
while the test tone is being
produced from the subwoofer
Flashing
Example: When the volume is set to –12 dB
while the subwoofer is selected
9
2
ENTER
After the above settings are completed, press the ENTER button again.
The “Channel Level” screen reappears.
To cancel the settings, select “Level Clear” and “Yes” on the “Channel Level” screen, then make the settings again.
The level of each channel should be adjusted to 75 dB (C-weighted, slow meter mode) on a sound level meter at the listening position.
If a sound level meter is not available adjust the channels by ear so the sound levels are the same. Because adjusting the subwoofer level test
tone by ear is difficult, use a well known music selection and adjust for natural balance.
NOTE: When adjusting the level of an active subwoofer system, you may also need to adjust the subwoofer’s own volume control.
When you adjust the channel levels while in the SYSTEM SETUP CHANNEL LEVEL mode, the channel level adjustments made will affect
ALL surround modes. Consider this mode a Master Channel Level adjustment mode.
2 After you have completed the SYSTEM SETUP CHANNEL LEVEL adjustments, you can then activate the individual surround modes and
adjust channel levels that will be remembered for each of those modes. Then, whenever you activate a particular surround sound mode,
your preferred channel level adjustments for just that mode will be recalled. Check the instructions for adjusting channel levels within each
surround mode on Page 43.
2 You can adjust the channel levels for each of the following surround modes: DIRECT, STEREO, 5 CH STEREO, DOLBY/DTS SURROUND,
HOME THX CINEMA, WIDE SCREEN, SUPER STADIUM, ROCK ARENA, JAZZ CLUB, CLASSIC CONCERT, MONO MOVIE, and MATRIX.
2 When using either surround speakers A or B, or when using surround speakers A and B at the same time, be sure to adjust the balance of
playback levels between each channel for the various selections of “A or B” and “A and B”.
2
23
Subwoofer peak limit level setting
• This unit features a subwoofer peak limit control which prevents distortion and damage in the loudspeaker system by controlling the maximum
bass volume level. With this feature you may set the maximum bass level for the system.
• This feature operates with or without a subwoofer in the system.
1
Use the CURSOR buttons to specify “Subwoofer Peak Limit Lev.” from
the “System Setup Menu” screen.
2
Switch to the Subwoofer Peak Limit Level Setting screen.
ENTER
3
Select “ON” for Peak Limiter.
4
The screen switches. Select “Setting Start”, then select “Yes”.
The screen switches and a test noise is produced from the speaker
system.
5
Increase the master volume level until the test noise is distorted.
The test noise (bass sound) is distorted when it sounds as if the input is
excessively high (when the sound crackles).
MASTER VOL.
6
2
24
ENTER
Press the ENTER button at the point where the test noise starts sounding distorted.
The AVR-5700 automatically sets the subwoofer peak limit level.
This prevents future inadvertent subwoofer overload due to excessively strong bass content when the master
volume control is at a high level.
Clear the subwoofer’s peak limit level setting by specifying “Peak Limiter” and “OFF”.
CAUTION!
• The master volume is set to “–30 dB” when test tones are output.
• The test tones are for confirming the low frequency playback limits and are played at an extremely high level. When using a low output
subwoofer, be very careful about irregular operations exceeding clipping by for example turning down the subwoofer’s attenuator before
starting then slowly turning the attenuator up to the listening level.
• Also, when the subwoofer is set to “NO” in the speaker configuration, the test tones are output from the front speakers. When using front
speakers with low input resistance, check that the sound is not clipped at sections where the signal is strong on the CD music source
before starting the peak limit setting. The peak limit setting should not be performed if the music source cannot be played with the master
volume set at “–15”. Set the front speakers to “small” and the subwoofer to “YES” in the speaker configuration. When this is done, the
low frequencies are cut, so the effect is insufficient. We strongly recommend adding a subwoofer.
• If the test tone is clipped when it is set to “–18 dB”, set the peak limit to “–18 dB”. In this case, the input resistance of the subwoofer or
front speakers is insufficient so clipping may occur when playing music. We recommend switching to a subwoofer with a higher input
resistance.
Setting the digital inputs
• This setting assigns the digital input jacks of the AVR-5700 for the different input sources.
1
2
At the System Setup Menu select “Digital Inputs”.
Switch to the Digital Inputs screen.
ENTER
3
4
Select the digital input jack to be assigned to the input source.
• To select the input source
• To select the digital input jack
Select “OFF” for input sources for which no digital input jacks are used.
2 If “Yes” is selected for “Default”, the settings are automatically reset to the default values.
Enter the setting.
The System Setup Menu reappears.
ENTER
NOTES:
• The OPTICAL 5 jacks on the AVR-5700’s rear panel are equipped with an optical digital output jack for recording digital signals on a DAT
deck, MD player or other digital recorder. Use this for digital recording between a digital audio source (stereo - 2 channel) and a digital audio
recorder.
• Do not connect the output of the component connected to the OPTICAL 5 OUT jack on the AVR-5700’s rear panel to any jack other than
the OPTICAL 5 IN jack.
• “PHONO”, “TAPE-2” and “TUNER” cannot be selected on the Digital Inputs screen.
25
Setting the on-screen display (OSD)
• Use this to turn the on-screen display (messages other than the menu screens) on or off.
1
2
At the System Setup Menu select “On Screen Display”.
Switch to the On Screen Display screen.
ENTER
3
Select “ON” or “OFF”.
4
Enter the setting.
The System Setup Menu reappears.
ENTER
Auto tuner presets
Use this to automatically search for FM broadcasts and store up to 40 stations at preset channels A1 to 8, B1 to 8, C1 to 8, D1 to 8 and E1 to 8.
NOTES:
• If an FM station cannot be preset automatically due to poor reception, use the “Manual tuning” operation to tune in the station, then preset it
using the manual “Preset memory” operation.
1
26
Use the CURSOR buttons to specify “Auto Tuner Presets” from the
“System Setup Menu” screen.
2
Press the ENTER button.
The “Auto Preset Memory” screen appears.
ENTER
3
2
Use the CURSOR button to select “Yes”.
“Search” flashes on the screen and searching begins.
“Completed” appears once searching is completed.
The display automatically switches to screen.
This completes system setup. Once these settings are made, there is no need to change them unless different AV components are
connected or the speakers are repositioned.
After completing system setup
This button can be pressed at any time during the system setup process to complete the process.
1
At the System Setup Menu, press the SYSTEM SETUP button.
2 The changed settings are entered and the on-screen display turns off.
SYSTEM
SETUP
TITLE
• On-screen display signals
On-screen display signal output
Signals input to the AVR-5700
VIDEO signal input jack (yellow)
S-video signal input jack
VIDEO MONITOR OUT-1 video
signal output jack (yellow)
1
E
E
A
A
2
A
E
A
E
3
E
A
E
A
4
A
A
E
A
(A: Signal E : No signal)
(A: On-screen signals output
S-video MONITOR OUT-1 video
signal output jack
E: On-screen signals not output)
NOTES:
• The on-screen display signals are not output from the video signal MONITOR OUT-2 (yellow) or S-Video signal MONITOR OUT-2 jacks.
• The on-screen display signals are not output from the color difference (component) video signal MONITOR OUT jacks.
• For 4 above, the on-screen display signals are output to the VIDEO MONITOR OUT-1 video signal output jack (yellow) if the monitor TV is
not connected to the S-video MONITOR OUT-1 video signal output jack.
27
8 REMOTE CONTROL UNIT
• The included remote control unit (RC-853) can be used to operate not only the AVR-5700 but other remote control compatible DENON
components as well. Furthermore, it is equipped with a function for learning the control signals of remote control units of other manufacturers,
so it can also be used to operate non-DENON remote control compatible video components.
Inserting the batteries
1 Remove the remote control unit’s rear cover.
2 Set two SUM3 (AA size) batteries in the battery compartment in
the indicated direction.
3 Put the rear cover back on.
Notes on Batteries
• Use SUM3 (AA size) batteries in the remote control unit.
• The batteries should be replaced with new ones approximately
once a year, though this depends on the frequency of usage.
• Even if less than a year has passed, replace the batteries with new
ones if the set does not operate even when the remote control
unit is operated nearby the set.
• When inserting the batteries, be sure to do so in the proper
direction, following the “< ” and “> ” marks in the battery
compartment.
• To prevent damage or leakage of battery fluid:
• Do not use a new battery together with an old one.
• Do not use two different types of batteries.
• Do not short-circuit, disassemble, heat or dispose of batteries in
flames.
• Remove the batteries from the remote control unit when you do
not plan to use it for an extended period of time.
• If the battery fluid should leak, carefully wipe the fluid off the
inside of the battery compartment and insert new batteries.
• When replacing the batteries, have the new batteries ready and
insert them as quickly as possible.
• The learned remote control signals may be cleared if no batteries
are in the remote control unit for about 5 seconds.
The factory-installed codes are in permanent memory, however.
Using the remote control unit
• Point the remote control unit at the remote sensor on the main
unit as shown on the diagram.
• The remote control unit can be used from a straight distance of
approximately 7 meters/22 feet from the main unit, but this
distance will be shorter if there are obstacles in the way or if the
remote control unit is not pointed directly at the remote sensor.
• The remote control unit can be operated at a horizontal angle of up
to 30 degrees with respect to the remote sensor.
Approx. 7 m/22 feet
28
NOTES:
• It may be difficult to operate the remote control unit if the remote
sensor is exposed to direct sunlight or strong artificial light.
• Do not press buttons on the main unit and remote control unit
simultaneously. Doing so may result in malfunction.
• Neon signs or other devices emitting pulse-type noise nearby may
result in malfunction, so keep the set as far away from such
devices as possible.
Operating DENON audio components
• Turn on the power of the different components before operating them.
1
Set mode switch 1 to “AUDIO (AVR/AVC)”.
AUDIO
START
SYSTEM CALL
SET
AVR/AVC
2
VIDEO
Set mode switch 2 to the position for the component to be
operated. (The tuner can be operated when the switch is at
any position but “LOCK”.)
CD
DECK MD
TUNER
RC-853
START
SYSTEM CALL
ON / SOURCE
SET
SHIFT
DVD
LEARNED/TX
POWER
CALL
OFF
VDP
1
2
3
1
2
3
V.AUX
PHONO
TV/DBS
V.AUX
PHONO
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
9
CHANNEL
TAPE-2 MON
+10
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
9
TV/VCR
VCR-2
A/B
+10
0
SHIFT
A
CHANNEL
TAPE-2 MON
TV/VCR
0
A/B
3
VOLUME
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
TV
VOLUME
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
When set to LOCK, only the buttons for the basic functions
of the AVR-5700 (sections A and B) will function. Use this
position for example to prevent children from accidentally
operating the system.
RC-853
ON / SOURCE
TUNER
TV/DBS
VCR-2
VDP VCR
1
AUDIO
CD
AVR/AVC
VIDEO
DECK MD
LOCK
DVD
TUNING
SYSTEM
SETUP
MASTER VOL.
AUDIO
MUTING
TV
VDP VCR
SURROUND
PARAMETER
2
VIDEO
DECK MD
B
MUTING
TV
VDP VCR
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
MENU/GUIDE
TITLE
BAND
CH SELECT
CH SELECT
ENTER
MODE
ENTER
MODE
SELECT
USE/LEARN T.TONE
LOCK
DVD
MENU/GUIDE
TITLE
3
CD
AVR/AVC
BAND
MEMORY
3
OFF
VDP
LOCK
DVD
2
LEARNED/TX
POWER
CALL
DVD
SELECT
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
MEMORY
USE/LEARN T.TONE
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
Operate the audio component.
• For details, refer to the component’s operating instructions.
2 While this remote control is compatible with a wide range of infrared controlled components, some models of components may not
be operated with this remote control.
1. CD player (CD) and MD recorder (MD) system buttons
TAPE-2 MON
VCR-2
+10
VOLUME
6,7
2
1
8,9
3
DISC
SKIP+
:
:
:
:
:
:
TV/VCR
VCR-2
A/B
+10
DISC SKIP+
Manual search (forward and reverse)
Stop
Play
Auto search (cue)
Pause
Switch discs
(for CD changers only)
3. Tuner system buttons
DVD
SHIFT
CHANNEL
+, –
TAPE-2 MON
A/B
VOLUME
:
:
:
:
:
:
A/B :
6
7
2
1
3
0
TV/VCR
DISC SKIP+
Rewind
Fast-forward
Stop
Forward play
Pause
Reverse play
Switch between decks A and B
2 For the tuner only, the following buttons can also be operated:
SYSTEM CALL
SET
2. Tape deck (DECK) system buttons
CALL
VDP
POWER
OFF
TUNER
1
2
3
TV/DBS
V.AUX
PHONO
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
9
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
TITLE
MENU/GUIDE
ON / SOURCE
SHIFT
BAND
CH SELECT
ENTER
MODE
SELECT
MEMORY
PANEL
ON SCREEN
DISPLAY
RETURN
CHANNEL
: Switch preset channel range
: Preset channel
up/down
TUNING
•, ª
BAND
MODE
MEMORY
: Frequency
up/down
: Switch between the AM and FM bands
: Switch between auto and mono
: Preset memory
29
Preset memory
• DENON and other makes of components can be operated by setting the preset memory for your make of video component. Operation is not
possible for some models, however. In this case use the learning function (see page 33) to store the remote control signals.
• For instructions on clearing the presettings stored in the preset memory, see page 36.
1
4
Set the slide switch to “VIDEO”.
AUDIO
AVR/AVC
Next, while holding the POWER button,
press the button for the code in block B.
(Refer to Table 1.) The operation is
completed when the button is released
and the LEARNED/TX LED lights.
VIDEO
START
SYSTEM CALL
SET
2
Set the slide switch to the component to
be registered (VDP, VCR or TV).
CD
DECK MD
3
OFF
VDP
1
2
3
TV/DBS
V.AUX
PHONO
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
TV
CHANNEL
9
TV/VCR
0
A/B
VOLUME
VDP VCR
the POWER button pressed in
( Keep
)
when performing steps 3 and 4
5
To continue registering other components,
repeat steps 2 to 4.
3,4
SHIFT
TAPE-2 MON
+10
LOCK
RC-853
ON / SOURCE
TUNER
VCR-2
DVD
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
4
MASTER VOL.
INPUT MODE
1
3
LEARNED/TX
POWER
CALL
DVD
ANALOG
AUDIO
CD
AVR/AVC
VIDEO
EXT.IN
DECK MD
LOCK
DVD
MUTING
2
TV
VDP VCR
Holding in the POWER button, press the
button for the corresponding manufacturer
in block A.
(Refer to Table 1.)
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
TITLE
MENU/GUIDE
BAND
CH SELECT
ENTER
MODE
SELECT
MEMORY
Flashes
USE/LEARN T.TONE
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
The LEARNED/TX LED flashes.
• This remote control unit can be used to operate components of other manufacturers without using the learning function by registering the
manufacturer of the component as shown on Table 1.
Table 1: Combinations of Personal System Codes for Different Manufacturers
“DVD”
“VDP”
DIRECT
STEREO
EXT.IN
(DIRECT)
(STEREO)
(EXT. IN)
B
A
B
A
DIRECT
STEREO
EXT.IN
(DIRECT)
(STEREO)
(EXT. IN)
1 (DVD)
DENON A
DENON B
—
1 (DVD)
DENON A
DENON B
DENON C
2 (VDP)
—
—
—
2 (VDP)
—
—
—
—
—
—
3 (TUNER)
MITSUBISHI
—
—
—
—
4 (TV/DBS)
PANASONIC
—
—
—
—
5 (V. AUX)
—
—
6 (PHONO)
SONY
—
—
6 (PHONO)
SONY A
7 (VCR-1)
PIONEER
—
—
7 (VCR-1)
PIONEER
—
—
8(CD)
3 (TUNER)
PANASONIC
4 (TV/DBS)
—
5 (V. AUX)
—
SONY B
SONY C
TOSHIBA
—
—
8 (CD)
—
—
—
9 (MD/TAPE-1)
—
—
—
9 (MD/TAPE-1)
—
—
—
(VCR-2)
—
—
—
(VCR-2)
—
—
—
—
—
—
—
—
—
2
30
Preset codes set upon shipment from the factory and when reset
“VCR”
“TV”
B
A
DIRECT
STEREO
EXT.IN
(DIRECT)
(STEREO)
(EXT. IN)
—
—
—
—
1 (DVD)
B
DIRECT
STEREO
(DIRECT)
(STEREO)
(EXT. IN)
1 (DVD)
—
—
—
2 (VDP)
DENON/HITACHI
—
—
A
EXT.IN
2 (VDP)
HITACHI A
HITACHI B
3 (TUNER)
MITSUBISHI A
MITSUBISHI B
MITSUBISHI C
3 (TUNER)
MITSUBISHI A
MITSUBISHI B
—
4 (TV/DBS)
PANASONIC A
PANASONIC B
PANASONIC C
4 (TV/DBS)
PANASONIC A
PANASONIC B
—
5 (V. AUX)
JVC (VICTOR) A
JVC (VICTOR) B
JVC (VICTOR) C
5 (V. AUX)
JVC (VICTOR)
—
—
6 (PHONO)
SONY A
SONY B
SONY C
6 (PHONO)
SONY
—
—
7 (VCR-1)
PIONEER
7 (VCR-1)
PIONEER
—
—
8 (CD)
TOSHIBA A
TOSHIBA B
—
8 (CD)
TOSHIBA
—
—
9 (MD/TAPE-1)
SANYO A
SANYO B
—
9 (MD/TAPE-1)
SANYO
—
—
(VCR-2)
SHARP A
SHARP B
—
(VCR-2)
SHARP
—
—
NEC A
NEC B
NEC
—
—
2
—
—
NEC C
Preset codes set upon shipment from the factory and when reset
NOTES:
• The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental operation, cover the remote control
unit’s transmitting window while setting the preset memory.
• Some models and years of manufacture of components of the manufacturers listed on Table 1 cannot be used.
• The signals stored at “learned” buttons have priority over the preset codes. If you wish to clear the “learned” signals, do so as described
on page 36.
• Some manufacturers use different types of remote control codes for their products. If the component does not operate when set to
remote codeset A, try setting to the B or C codesets.
31
Operating a video component stored in the preset memory
1
Set the slide switch to “VIDEO”.
AUDIO
START
SYSTEM CALL
SET
AVR/AVC
2
VIDEO
DECK MD
OFF
VDP
2
3
V.AUX
PHONO
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
3
3
SHIFT
1
TV/DBS
CHANNEL
9
TAPE-2 MON
+10
RC-853
ON / SOURCE
TUNER
VCR-2
Set the slide switch to the component to be registered (VDP,
VCR or TV).
CD
LEARNED/TX
POWER
CALL
DVD
TV/VCR
0
A/B
VOLUME
DISC SKIP+
LOCK
DVD
TV
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
VDP VCR
1
AUDIO
CD
AVR/AVC
VIDEO
DECK MD
LOCK
DVD
MUTING
2
TV
VDP VCR
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
TITLE
MENU/GUIDE
BAND
CH SELECT
3
SELECT
USE/LEARN T.TONE
3
3
ENTER
MODE
MEMORY
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
Operate the video component.
• For details, refer to the component’s operating instructions.
2 Some models cannot be operated with this remote control unit.
SYSTEM CALL
SET
OFF
VDP
DVD
1. Digital video disc player (DVD) system buttons
POWER
CALL
ON / SOURCE
TUNER
1
2
3
TV/DBS
V.AUX
PHONO
4
5
6
VCR-1
CD
7
8
SHIFT
MD / TAPE-1
CHANNEL
9
TAPE-2 MON
VCR-2
+10
TV/VCR
0
A/B
POWER
6,7
2
1
8,9
3
TITLE
VOLUME
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
MASTER VOL.
INPUT MODE
ANALOG
VIDEO
EXT.IN
DECK MD
CD
AVR/AVC
Turns power on and off
Manual search (forward and reverse)
Stop
Play
Auto search (cue)
Pause
Call out title
MENU
DISPLAY
DVD SET UP
RETURN
•, ª
0, 1
SELECT
:
:
:
:
:
:
:
Call out menu
Switch display
DVD setup
Menu return
Cursor up/down
Cursor left/right
Enter setting
DISC SKIP+
HOME THX CINEMA
AUDIO
:
:
:
:
:
:
:
LOCK
DVD
NOTE:
Some manufacturers use different names for the DVD remote control buttons, so also refer to the instructions on
remote control for that component.
MUTING
TV
VDP VCR
SYSTEM
SETUP
TUNING
SURROUND
PARAMETER
MENU/GUIDE
TITLE
BAND
CH SELECT
ENTER
MODE
SELECT
MEMORY
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
USE/LEARN T.TONE
2. Video disc player (VDP) system
buttons
SYSTEM CALL
SET
CALL
SYSTEM CALL
POWER
OFF
DVD
VDP
TUNER
1
2
3
TV/DBS
V.AUX
PHONO
CALL
SYSTEM CALL
POWER
ON / SOURCE
SET
SHIFT
DVD
VDP
TUNER
1
2
OFF
3
TV/DBS
V.AUX
PHONO
4. Monitor TV system buttons
CALL
POWER
ON / SOURCE
SET
SHIFT
DVD
VDP
TUNER
1
2
OFF
3
TV/DBS
V.AUX
PHONO
4
5
6
4
5
6
4
5
6
VCR-1
CD
MD / TAPE-1
VCR-1
CD
MD / TAPE-1
VCR-1
CD
MD / TAPE-1
7
8
9
7
8
9
7
8
TAPE-2 MON
VCR-2
TAPE-2 MON
VCR-2
VCR-2
+10
0
VOLUME
POWER
6,7
2
1
8,9
3
32
3. Video deck (VCR) system buttons
CHANNEL
TV/VCR
+10
A/B
VOLUME
DISC SKIP+
: Power on/off
: Manual search
(forward and reverse)
: Stop
: Play
: Auto search (cue)
: Pause
0
POWER
6,7
2
1
3
CHANNEL
+, –
CHANNEL
TV/VCR
A/B
DISC SKIP+
: Power on/off
: Manual search
(forward and reverse)
: Stop
: Play
: Pause
: Switch channel
0
VOLUME
POWER
VOLUME
•,ª
TV/VCR
CHANNEL
+, –
SHIFT
CHANNEL
9
TAPE-2 MON
+10
ON / SOURCE
TV/VCR
A/B
DISC SKIP+
: Power on/off
: Volume
up/down
: Switch between TV and VCR
: Switch channel
Learning function
• If your AV component is not a DENON product or it cannot be operated with the preset memory codesets, you can “teach” the AVR-5700’s
remote control to “learn” the codes from the component’s original remote control.
• The buttons that can be “learned” are the CD, DECK and MD system buttons (see page 29) and the DVD, VDP, VCR and TV system buttons
(see page 32). (For the CD, MD, DVD, VDP and TV, the A block buttons can also be “learned”, and for the DVD and TV, the B block buttons
can also be “learned”.)
SET
1
A
Press the USE/LEARN selector button with the tip of a pen
etc., to set the learn mode. Both the START and
Flashes
LEARNED/TX indicators flash.
CALL
OFF
ON / SOURCE
DVD
VDP
TUNER
1
2
3
TV/DBS
V.AUX
PHONO
4
5
VCR-1
CD
7
8
SHIFT
6
MD / TAPE-1
CHANNEL
9
TAPE-2 MON
VCR-2
+10
TV/VCR
0
A/B
4
VOLUME
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
2
This unit’s remote
control unit
AUDIO
CD
AVR/AVC
VIDEO
DECK MD
LOCK
DVD
MUTING
TV
VDP VCR
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
3
MENU/GUIDE
TITLE
BAND
CH SELECT
2
Set the program switch to the side to be “learned”.
Set to the AUDIO side for the CD, tape deck or DAT position,
to the VIDEO side for the VDP, VCR or TV position.
B
ENTER
MODE
SELECT
MEMORY
1,8
USE/LEARN T.TONE
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
AUDIO
AVR/AVC
3
5
VIDEO
Check that the START LED is lit, then press the button to be
“learned” on the other remote control unit.
Set the program switch to the position to be “learned”.
CD
DECK MD
Other remote
control unit
LOCK
DVD
TV
VDP VCR
This unit’s remote
control unit
4
Set the remote control units so they are facing each other,
then press the button to be “learned” on this unit’s remote
control unit.
Transmitting windows
6
Once the START LED turns off and the LEARNED/TX LED
lights, release the button on the other remote control unit.
Other remote
control unit
Lit
This unit’s remote
control unit
Approx.
5 cm
The indicator stops flashing and the START LED lights.
The learnable buttons are the buttons which can be operated
with the DENON system codes for the CD player, DAT and
tape deck, the buttons which can be operated with the
preset memory for the VCR, VDP and TV. For the TV only,
however, the buttons in the section indicated “A” on the
diagram above can also be “learned”. Use these to “learn”
TV channels.
The two LEDs start
flashing again.
7
8
Lit
To “learn” other buttons, repeat steps 2 to 6.
Once the learning operation is completed, press the
USE/LEARN selector button again.
The two LEDs stop flashing and the learning mode is
cancelled.
Check that the stored
codes work properly.
NOTES:
• Up to 26 codes can be “learned”, but this number may be lower if the codes are long.
• If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once again light when the button(s)
is released.
• If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For limited number of models,
codes cannot be stored in RC-853.
• If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full, and the code you have just
attempted to store was not stored.
To “learn” that code, first perform the resetting operation. (See page 36.)
33
System call function
• The included remote control unit is equipped with a system call function for transmitting multiple remote control signals when a single button
is pressed (this is often referred to as a “macro” function).
This function can be used to turn on the amplifier’s power, select the input source, turn on the monitor TV’s power, turn on a source
component’s power and start playback, etc., all at the touch of a button.
(1) System call buttons
The buttons that can be used for the system call function are shown on the table below.
A series of up to 10 operations can be performed with the POWER ON and OFF buttons, and a series of up to 5 operations can be performed
with other buttons.
System call signals are already preset at the buttons indicated in the shaded section. System call signals can also be stored at any button on
the remote control unit, including the buttons in this section. (See page 35.)
Button
No.
transmissions
POWER OFF
(key 3)
10
POWER OFF
(key 4)
10
DVD (key 5)
VDP (key 6)
Stored
operation 1
Stored
operation 2
Stored
operation 3
Stored
operation 4
Stored
operation 5
5
Receiver
power on
DVD player
(DVD)
power on
Receiver
input source
switched to
DVD
TV power on
DVD player
(DVD)
playback
5
Receiver
power on
LD player
(VDP)
power on
Receiver
input source
switched to
VDP
TV power on
LD player
(VDP)
playback
TV/DBS
(key 9)
5
Receiver
power on
TV power on
Receiver
input source
switched to
TV/DBS
V.AUX
(key 10)
5
Receiver
power on
TV power on
Receiver
input source
switched to
V.AUX
VCR-1
(key 13)
5
Receiver
power on
Video (VCR)
power on
Receiver
input source
switched to
VCR-1
CD (key 14)
5
Receiver
power on
Receiver
input source
switched to
CD
TV power on
Stored
operation 6
Stored
operation 7
Stored
operation 8
Stored
operation 9
The system call signals for the POWER OFF and
POWER ON buttons are transmitted from the
remote control unit approximately once every
second.
The signals for the other buttons (DVD, VDP,
TV/DBS, V.AUX, VCR-1 and CD) are transmitted
approximately once every 1.5 seconds.
Video (VCR)
playback
(2) Using the system call function
1
Press the system call button.
• The LEARNED/TX LED flashes for 5 seconds.
1
START
SYSTEM CALL
SET
CALL
2
LEARNED/TX
POWER
CALL
OFF
VDP
TUNER
1
2
3
TV/DBS
V.AUX
PHONO
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
2
SHIFT
CHANNEL
9
TAPE-2 MON
+10
RC-853
ON / SOURCE
DVD
VCR-2
Press the button at which the desired system call signals are
stored while the LEARNED/TX LED is flashing.
• The preset signals or the signals you have stored at that
button are transmitted in succession.
TV/VCR
0
A/B
VOLUME
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
AUDIO
CD
AVR/AVC
VIDEO
DECK MD
LOCK
DVD
MUTING
TV
VDP VCR
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
TITLE
MENU/GUIDE
BAND
CH SELECT
MODE
34
Stored
operation 10
ENTER
(3) Storing signals
(4) Clearing system call settings
START
SYSTEM CALL
1,5
SET
2
LEARNED/TX
POWER
CALL
OFF
VDP
DVD
RC-853
START
SYSTEM CALL
1,3
ON / SOURCE
TUNER
SHIFT
SET
LEARNED/TX
POWER
CALL
OFF
VDP
DVD
1
2
3
1
2
3
TV/DBS
V.AUX
PHONO
TV/DBS
V.AUX
PHONO
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
9
VCR-2
TAPE-2 MON
+10
2
CHANNEL
0
VOLUME
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
TV/VCR
VCR-2
A/B
+10
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
AUDIO
CD
AVR/AVC
VIDEO
DECK MD
LOCK
DVD
TV/VCR
0
A/B
VOLUME
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
AUDIO
MUTING
TV
CD
AVR/AVC
VIDEO
DECK MD
LOCK
DVD
MUTING
TV
VDP VCR
SYSTEM
SETUP
SURROUND
PARAMETER
TITLE
MENU/GUIDE
TUNING
BAND
SYSTEM
SETUP
SURROUND
PARAMETER
TITLE
MENU/GUIDE
BAND
CH SELECT
CH SELECT
ENTER
MODE
ENTER
MODE
SELECT
MEMORY
USE/LEARN T.TONE
1
CHANNEL
9
VDP VCR
TUNING
SHIFT
TAPE-2 MON
MASTER VOL.
3
RC-853
ON / SOURCE
TUNER
SELECT
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
MEMORY
USE/LEARN T.TONE
Press the SET button.
• The START LED and LEARNED/TX LED both flash.
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
1
Press the SET button.
2
3
Press the button whose settings you want to clear.
SET
SET
2
Press the button at which you want to store the system call
signals.
• The START LED flashes.
3
Set the mode switch to the position for the component
whose remote control signals you want to store.
Press the SET button.
• The button is reset to the settings shown on the table on
page 34.
SET
CD
AUDIO
AVR/AVC
DECK MD
LOCK
DVD
VIDEO
TV
VDP VCR
4
5
Press the buttons whose remote control signals you want to
store one by one.
Press the SET button.
SET
NOTES:
• The remote control signals for the buttons pressed while storing the system call signals are transmitted when the buttons are pressed, so
cover the remote sensor or take other measures so that the components do not operate while the signals are being stored.
• The LEARNED/TX LED does not light if system call signals cannot be stored at the button that you have pressed or if you have already
stored the maximum number of signals.
35
Clearing “learned” remote control signals and resetting the preset memory
1
START
SYSTEM CALL
4
Press the USE/LEARN selector button with the tip of a pen,
etc., to set the learn mode.
SET
LEARNED/TX
POWER
CALL
OFF
ON / SOURCE
DVD
VDP
TUNER
1
2
3
TV/DBS
V.AUX
PHONO
SHIFT
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
CHANNEL
9
TAPE-2 MON
VCR-2
+10
TV/VCR
0
A/B
VOLUME
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
2
To clear “learned” remote control signals, set the slide
switch to the position at which the signals were “learned”.
To clear the preset memory settings, set the slide switch to
“VIDEO”.
2
AUDIO
CD
AVR/AVC
VIDEO
DECK MD
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
TITLE
MENU/GUIDE
CH SELECT
ENTER
SELECT
MEMORY
1,5
VIDEO
Set the slide switch to the position at which the signals were
“learned” or at which the preset memory settings were set.
CD
3
BAND
MODE
3
MUTING
TV
VDP VCR
AUDIO
AVR/AVC
LOCK
DVD
DECK MD
4
USE/LEARN T.TONE
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
Press the SYSTEM CALL SET button, and hold it in for at
least four seconds.
• When both the START and LEARNED/TX LEDs light
simultaneously, all the stored codes are cleared.
Lit
LOCK
DVD
TV
VDP VCR
5
9 OPERATION
Press the USE/LEARN selector button.
Before operating
1
2
Refer to “CONNECTIONS” (pages 6 to 13) and check that all
connections are correct.
Set the remote control unit’s slide switch to the AUDIO
position. (only when operating with the remote control unit)
AUDIO
AVR/AVC
3
VIDEO
3
Turn on the power.
Press the POWER switch (button).
START
SYSTEM CALL
SET
ON / SOURCE
ON/STANDBY
Lights
OFF
VDP
DVD
ON / STANDBY
LEARNED/TX
POWER
CALL
TUNER
1
2
3
TV/DBS
V.AUX
PHONO
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
SHIFT
3
CHANNEL
9
VCR-2
TAPE-2 MON
+10
RC-853
ON / SOURCE
0
TV/VCR
A/B
OFF
VOLUME
(Main unit)
(Remote control unit)
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
2
AUDIO
CD
AVR/AVC
VIDEO
DECK MD
LOCK
DVD
MUTING
TV
VDP VCR
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
• ¢ ON/STANDBY
The power turns on and “ON/STANDBY” indicator is lit.
Several seconds are required from the time the power switch is set to the “ON” position until sound is output. This is due to the built-in
muting circuit that prevents noise when the power switch is turned on and off.
Set the POWER switch to this position to turn the power on and off from the included remote control unit (RC-853).
• £ OFF
The power turns off and “ON/STANDBY” indicator is off.
In this position, the power cannot be turned on and off from the remote control unit.
36
Playing the input source
START
SYSTEM CALL
SET
1
3
5
OFF
VDP
DVD
1
LEARNED/TX
POWER
CALL
TUNER
1
2
3
TV/DBS
V.AUX
PHONO
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
TAPE-2 MON
0
2
CD
8
(Main unit)
2
(Remote control unit)
When the tape 2 input (TAPE-2 MON)
is selected, the input indicator lights.
Lit
Select the input mode.
• Selecting the analog mode
Press the ANALOG button to switch to the analog input.
ANALOG
ANALOG
(Main unit)
(Remote control unit)
• Selecting the external input (6CH/8CH EXT. IN) mode
Press the 6CH/8CH EXT. IN (on the EXT. IN button on the
remote control unit) to switch the external input.
6CH / 8CH
EXT. IN
EXT.IN
(Main unit)
(Remote control unit)
• Selecting the AUTO, DIGITAL, PCM and RF modes
The mode switches as shown below each time the INPUT
MODE button is pressed.
AUTO
DIGITAL
PCM
(RF)
INPUT MODE
INPUT MODE
(Main unit)
2
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
5
MASTER VOL.
AUDIO
CD
VIDEO
TUNING
Example: CD
2
DOLBY / DTS
SURROUND
DECK MD
LOCK
DVD
MUTING
TV
VDP VCR
Select the input source to be played.
INPUT SELECTOR
TV/VCR
DISC SKIP+
HOME THX CINEMA
AVR/AVC
Lightly press on the bottom of
the door to open it.
1
CHANNEL
A/B
VOLUME
3
2
SHIFT
9
VCR-2
+10
RC-853
ON / SOURCE
(Remote control unit)
The RF mode can only be selected when the program
source is set to VDP.
SYSTEM
SETUP
SURROUND
PARAMETER
TITLE
MENU/GUIDE
Input mode selection function
Different input modes can be selected for the different input
sources. The selected input modes for the separate input sources
are stored in the memory.
1 AUTO (All auto mode)
In this mode, the types of signals being input to the digital and
analog input jacks for the selected input source are detected and
the program in the AVR-5700’s surround decoder is selected
automatically upon playback. This mode can be selected for all
input sources other than PHONO, TAPE-2 and TUNER.
The presence or absence of digital signals is detected, the signals
input to the digital input jacks are identified and decoding and
playback are performed automatically in DTS, Dolby Digital or
PCM (2 channel stereo) format. If no digital signal is being input,
the analog input jacks are selected.
With a VDP input (used most often for Laser Disc), the presence
or absence of a Dolby Digital AC-3 RF signal is also detected. If an
AC-3 RF signal is detected at the Dolby Digital AC-3 RF jack, the
RF signals are decoded and played with priority.
2 DIGITAL (Digital auto mode)
The signals being input to the digital input jacks are identified and
decoding and playback are performed automatically in DTS, Dolby
Digital or PCM format
3 PCM (exclusive PCM signal playback mode)
Decoding and playback are only performed when PCM signals are
being input.
4 RF (exclusive RF signal playback mode)
This can only be selected when the program source is set to VDP.
Decoding and playback are only performed when RF signals are
being input. This is used when the LD player has an AC-3 RF
output jack, but does not have a PCM digital output jack.
5 ANALOG (exclusive analog audio signal playback mode)
The signals input to the analog input jacks are decoded and
played.
6 6CH/8CH EXT. IN (external decoder input jack selection mode)
The signals being input to the external decoder input jacks are
played without passing through the surround circuitry.
NOTES:
• When the AUTO (all auto) mode is selected for the VDP program
source and the mode is switched from pause or chapter skip, etc.,
to playback while playing the Dolby Digital sound of an LD, the
PCM/analog sound may be output momentarily before the sound
switches to Dolby Digital. If this happens, switch to the “RF”
(fixed RF input) mode and the sound will not be interrupted. That is
due to the fact that when paused or during chapter skip, the AC-3
RF signal is interrupted.
• When playing PCM signals in the DIGITAL (digital auto) mode, the
sound may be briefly interrupted when playback starts after
searching on CDs or LDs, depending on how the signals are
recorded on the disc. If this happens, switch to the “PCM”
(exclusive PCM signal playback) mode to prevent the sound from
being interrupted.
• Note that noise will be output when CDs or LDs recorded in DTS
format are played in the “PCM” (exclusive PCM signal playback) or
“ANALOG” (exclusive PCM signal playback) mode. Select the
AUTO (all auto) or DIGITAL (digital auto) mode when playing
signals recorded in DTS from a laser disc player.
37
3
Input mode display
Select the play mode.
One of these lights, depending on the
input signal.
Example: Stereo
• In the AUTO mode
STEREO
ANALOG
STEREO
DIGITAL
• In the DIGITAL AUTO mode
DIGITAL
(Main unit)
(Remote control unit)
• In the DIGITAL PCM mode
4
Start playback on the selected component.
• For operating instructions, refer to the component’s
manual.
5
Adjust the volume.
DIGITAL
• When switched to RF in the VDP RF or AUTO mode
DIGITAL
MASTER VOLUME
MASTER VOL.
• In the ANALOG mode
ANALOG
The volume level is
displayed on the
master volume level
display.
2
(Main unit)
(Remote control unit)
The volume can be adjusted within the range of –60 to 0 to 18 dB,
in steps of 1 dB. However, when the channel level is set as
described on page 22 or pages 43 and 44, if the volume for any
channel is set at +1 dB or greater, the volume cannot be adjusted
up to 18 dB. (In this case the maximum volume adjustment range
is “18 dB — (Maximum value of channel level)”.)
Input mode when playing DTS sources
• Noise will be output if DTS-compatible CDs or LDs are played in
the “ANALOG” or “PCM” mode.
When playing DTS-compatible sources, be sure to connect the
source component to the digital input jacks (OPTICAL/COAXIAL)
and set the input mode to “AUTO” or “DIGITAL”.
Input signal display
• DOLBY DIGITAL
L
CH INDICATOR
C
R
S
SL
SR
One of these lights, depending on the
input signal.
LOCK
LFE
LOCK
DIGITAL
PRO LOGIC
• DTS
L
CH INDICATOR
C
R
S
SL
SR
Lit
LOCK
LOCK
LFE
• PCM
L
SL
2
CH INDICATOR
C
R
S
SR
LOCK
LOCK
LFE
The LOCK LED lights when digital signals are being input properly.
If the LED does not light, check whether the digital input
component setup (page 25) and connections are correct and
whether the component’s power is turned on.
NOTE:
• The digital input indicator will light (green) when playing CDROMs containing data other than audio signals, but no sound
will be heard.
38
After starting playback
[1] Adjusting the sound quality (tone)
The tone control function will not work in the direct or Home THX
Cinema mode.
1
Adjust the bass sound to the desired level using the BASS
adjustment control, the treble sound using the TREBLE
adjustment control.
BASS
TREBLE
[2] Listening over headphones
Plug the headphones’ plug into the jack.
2 Connect the headphones to the PHONES jack.
The pre-out output (including the speaker output) is automatically
turned off when headphones are connected.
NOTE:
To prevent hearing loss, do not raise the volume level excessively
when using headphones.
• To increase the bass or treble: Turn the control clockwise.
(The bass or treble sound can be increased to up to +12
dB in steps of 2 dB.)
• To decrease the bass or treble: Turn the control clockwise.
(The bass or treble sound can be decreased to up to –12
dB in steps of 2 dB.)
2
If you do not want the bass and treble
to be adjusted, turn on the tone defeat
mode.
2 The signals do not pass through the
bass and treble adjustment circuits,
providing higher quality sound.
TONE
DEFEAT
2
1
Lightly press on the bottom of
the door to open it.
[3] Turning the sound off temporarily (muting)
1
Use this to turn off the audio output
temporarily.
Press the MUTING button.
2 Cancelling MUTING mode.
Press the MUTING button again.
MUTING
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
AUDIO
CD
AVR/AVC
VIDEO
DECK MD
LOCK
DVD
MUTING
TV
1
VDP VCR
[4] Combining the currently playing sound with the desired image
1
Simulcast playback
VIDEO
Use this switch to monitor a video
SELECT
source other than the audio source.
Press the VIDEO SELECT button
repeatedly until the desired source
appears on the display.
2 Cancelling simulcast playback.
• Select “SOURCE” using the video select button.
• Switch the program source to the component connected
to the video input.
1
[5] Checking the currently playing program source, etc.
1
On screen display
• Each time an operation is performed, a
description of that operation appears
on the display connected to the unit’s
VIDEO MONITOR OUT jack. Also, the
unit’s operating status can be checked
during playback by pressing the remote
control unit’s ON SCREEN button.
Such information as the position of the
input selector and the surround
parameter settings is output in
sequence.
Front panel display
• Descriptions of the unit’s
operations are also
PANEL
displayed on the front
panel display. In addition,
the display can be
switched to check the
unit’s operating status
while playing a source by
(Main unit)
pressing the PANEL
button.
TUNING
ON SCREEN
SYSTEM
SETUP
SURROUND
PARAMETER
MENU/GUIDE
TITLE
BAND
CH SELECT
ENTER
MODE
RETURN
SELECT
MEMORY
USE/LEARN T.TONE
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
1
1
1
PANEL
DISPLAY
(Remote control unit)
Using the dimmer function
• Use this to change the brightness of the display.
The display brightness changes in four steps
(bright, medium, dim and off) by pressing the
remote control unit’s DIMMER button
repeatedly.
2 The brightness changes in 3 steps each time the
button is pressed, and finally the display turns
off.
DIMMER
39
Multi-source recording/playback
[1] Playing one source while recording another (REC OUT mode)
1
Press the REC/MULTI MODE button
until “REC OUT SOURCE” appears on
the set’s display.
2
Press the REC/MULTI SOURCE button
until the source you want to record
appears on the set’s display.
• The indicator for the selected
program source lights.
1,2
MODE
SOURCE
1,4 2,4
2
Display
3
Set the recording mode.
• For operating instructions, refer to the manual of the
component on which you want to record.
4
To cancel, press the REC/MULTI MODE button or press the
REC/MULTI SOURCE button until “SOURCE” appears on the
display.
MODE
SOURCE
Or
PHONO CD TUNER AUX DVD /
VCR
-1 -2
V.AUX MD /
VDP TV / DBS
TAPE -1 -2
NOTES:
• Recording sources other than digital inputs selected in the REC
OUT mode are also output to the multi source audio/video
output jacks.
• Digital signals are not output from the REC SOURCE or
audio/video output jacks.
[2] Outputting a program source to an amplifier, etc., in a different room (MULTI mode)
1
Press the REC/MULTI MODE button
until “M-SOURCE SOURCE” appears
on the set’s display.
2
Press the REC/MULTI SOURCE button
until the source you want to output
appears on the set’s display.
• The “MULTI” indicator lights.
• The indicator for the selected
program source lights.
• When the AVR-5700 is in the REC
OUT mode, the source cannot be
output using the MULTI button on
the remote control unit.
1,2
MODE
SOURCE
1,4 2,4
(Main unit)
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
MENU/GUIDE
TITLE
BAND
CH SELECT
ENTER
MODE
SELECT
MEMORY
MULTI
USE/LEARN T.TONE
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
2
(Remote control unit)
3
Start playing the source to be output.
• For operating instructions, refer to the manuals of the
respective components.
4
To cancel, either press the REC/MULTI MODE button or
press the REC/MULTI SOURCE button until “SOURCE”
appears on the display.
MODE
SOURCE
Or
40
2
Display
REC
MULTI
PHONO CD TUNER AUX DVD /
VCR
-1 -2
V.AUX MD /
VDP TV / DBS
TAPE -1 -2
NOTES:
• The signals of the source selected in the MULTI mode are also
output from the DAT/TAPE-1 and VCR recording output
terminals.
• Digital signals are not output from the multi source audio
output jacks.
Playback using the external input (EXT. IN) jacks
1
Set the external input
(6CH/8CH EXT. IN) mode.
Press the 6CH/8CH EXT. IN
(on the EXT. IN button on
the remote control unit) to
switch the external input.
6CH / 8CH
EXT. IN
(Main unit)
EXT.IN
(Remote control unit)
Once this is selected, the input signals connected to the FL
(front left), FR (front right), C (center), SL (surround left) and
SR (surround right) channels of the EXT. IN jacks are output
directly to the front (left and right), center and surround (left
and right) speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer) jack is
output to the PRE OUT SUBWOOFER jack.
When 6CH/8CH EXT. IN is selected, the input signals
connected to the EL (effect left) and ER (effect right)
jacks are output to the PRE OUT effect (left and right)
jacks.
2
Canceling the external input mode
To cancel the external input (6CH/8CH EXT. IN) setting, press
the INPUT MODE or ANALOG button to switch to the
desired input mode. (See page 37.)
2 1
Lightly press on the bottom of
the door to open it.
VOLUME
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
2
AUDIO
CD
AVR/AVC
VIDEO
DECK MD
LOCK
DVD
MUTING
1
TV
VDP VCR
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
TITLE
MENU/GUIDE
BAND
INPUT MODE
ANALOG
CH SELECT
INPUT MODE
(Main unit)
ANALOG
MODE
ENTER
SELECT
(Remote control unit)
• When the input mode is set to the external input (6CH/8CH EXT. IN), the play mode (DIRECT, STEREO, DOLBY/DTS SURROUND, WIDE
SCREEN, 5CH STEREO or DSP SIMULATION) cannot be set.
NOTES:
• In play modes other than the external input mode, the signals connected to these jacks cannot be played. In addition, signals cannot be
output from channels not connected to the input jacks.
• The external input mode can be set for any input source. To watch video while listening to sound, select the input source to which the
video signal is connected, then set this mode.
41
Multi-source and multi-zone playback
MULTI ROOM MUSIC ENTERTAINMENT SYSTEM
• When the outputs of the MULTI SOURCE AUDIO OUT terminals are wired and connected to integrated amplifiers installed in other rooms,
different sources can be played in rooms other than the main room in which this unit and the playback devices are installed. (Refer to
ANOTHER ROOM on the diagram below.)
• When a sold separately room-to-room remote control unit (DENON RC-616, 617 or 618) is wired and connected between the main room and
another room, the remote-controllable devices in the main room can be controlled from another room using the remote control unit.
2 To control playback devices other than the ones above, either use that device’s remote control unit or preset a separately sold programmable
remote control unit.
NOTES:
• For the AUDIO output, use high quality pin-plug cords and wire in such a way that there is no humming or noise.
• For instructions on installation and operation of separately sold devices, refer to the devices’ operating instructions.
MULTI ROOM MUSIC ENTERTAINMENT SYSTEM
ANOTHER ROOM
MAIN ROOM
RC-617
INTEGRATED
AMPLIFIER
ROOM-TO-ROOM REMOTE CONTROL SYSTEM
(separately sold) control line
PROGRAMMABLE
REMOTE
CONTROL UNIT
AVR-5700
MULTI SOURCE AUDIO signal cable
SPEAKER cable
2 Refer to CONNECTIONS on pages 6 to 13.
RC-616
SYSTEM REMOTE
CONTROL UNIT RC-853
Room to Room Remote Control jacks
• The OUT jack is an extension jack for future use.
• When the OUT jack is connected, the signals input to the IN jack are output from the OUT jack directly. (Example: RC616 signals are output.)
• Do not connect only the OUT jack.
(The signals from the AVR-5700’s remote sensor are not output to this jack.)
42
10 SURROUND
Before playing with the surround function
• Before playing with the surround function, be sure to use the test tones to adjust the playback level from the different speakers. This
adjustment can be performed with the system setup (see page 22) or from the remote control unit, as described below.
• Adjusting with the remote control unit using the test tones is only possible in the “Auto” mode and only effective in the DOLBY SURROUND
and HOME THX CINEMA modes. The adjusted levels for the different modes are automatically stored in the memory.
1
Press the T. TONE button.
SYSTEM
SETUP
TUNING
SURROUND
PARAMETER
TITLE
MENU/GUIDE
BAND
CH SELECT
2
ENTER
MODE
SELECT
MEMORY
T.TONE
1,3
USE/LEARN T.TONE
2
Test tones are output from the different speakers. Use the
channel volume adjust buttons to adjust so that the volume
of the test tones is the same for all the speakers.
3
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
After completing the adjustment, press the T. TONE button
again.
T.TONE
2
Test tone signals are not output to the EL and ER channels.
• After adjusting using the test tones, adjust the channel levels either according to the playback sources or to suit your tastes, as described
below.
1
Select the speaker whose level you want to adjust.
START
SYSTEM CALL
CH SELECT
SET
ENTER
LEARNED/TX
POWER
CALL
OFF
VDP
DVD
1
2
3
TV/DBS
V.AUX
PHONO
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
SHIFT
CHANNEL
9
VCR-2
TAPE-2 MON
+10
The channel switches as shown below each time the button
is pressed.
TV/VCR
0
A/B
VOLUME
1 FL
FADER 0
1 C
1 FR
SW 0
1 SR
ER 0
2
1 SL
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
EL 0
MASTER VOL.
2
AUDIO
2
RC-853
ON / SOURCE
TUNER
Adjust the level of the selected speaker.
CD
AVR/AVC
VIDEO
DECK MD
LOCK
DVD
MUTING
TV
VDP VCR
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
MENU/GUIDE
TITLE
BAND
CH SELECT
1
SELECT
MEMORY
USE/LEARN T.TONE
2
2
ENTER
MODE
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
The EL and ER channels can only be adjusted when
“6CH/8CH EXTERNAL INPUT” is selected.
43
Fader function
• This function makes it possible to lower the volume of the front channels (FL, C and FR) or the rear channels (SL and SR) together. Use it for
example to adjust the balance of the sound from the different positions when playing multi-channel music sources.
1
Select “FADER”.
CH SELECT
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
ENTER
MASTER VOL.
AUDIO
CD
AVR/AVC
VIDEO
DECK MD
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
TITLE
MENU/GUIDE
BAND
CH SELECT
FADER 0
1 FR
SW 0
1 SR
ER 0
2
2
2
1 SL
EL 0
2
SELECT
MEMORY
USE/LEARN T.TONE
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
2
The EL and ER channels can only be adjusted when
“6CH/8CH EXTERNAL INPUT” is selected.
Press the
button to reduce the volume of the front
channels, the
button to reduce the volume of the rear
channels.
2 The fader function does not affect the
SW, EL and ER channels.
The channel whose channel level is adjusted lowest can be faded
to –12 dB using the fader function.
If the channel levels are adjusted separately after adjusting the
fader, the fader adjustment values are cleared, so adjust the fader
again.
2
1
2
ENTER
MODE
1 C
MUTING
TV
VDP VCR
The channel switches in the order shown below each time
this button is pressed.
1 FL
LOCK
DVD
This is only displayed when setting the fader control.
Dolby Surround Pro Logic mode
1
Select the Dolby Surround Pro Logic mode.
• The Dolby Pro Logic indicator lights.
DOLBY / DTS
SURROUND
(Main unit)
2
DOLBY / DTS
SURROUND
Lit
(Remote control unit)
1
Play a program source with the
mark.
• For operating instructions, refer to the manuals of the
respective components.
VOLUME
1
NOTE:
• There are four Dolby Surround Pro Logic modes (NORMAL,
PHANTOM, WIDE and 3CH. LOGIC). The AVR-5700 sets the
mode automatically according to the types of speakers set
during the system setup process (page 18).
44
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
Dolby Digital mode (only with Dolby Digital RF or digital input) and DTS Surround (only with digital
input)
1
Select the input source.
Playback with a Dolby Digital RF input
1 Select VDP for the input.
INPUT SELECTOR
1
VDP
3
2
(Main unit)
(Remote control unit)
2 Set the input mode to “AUTO” or “RF”.
INPUT MODE
INPUT MODE
2
1
(Main unit)
(Remote control unit)
START
SYSTEM CALL
SET
Playback with a digital input
1
1 Select an input source set to digital (COAXIAL/OPTICAL)
(see page 25).
LEARNED/TX
POWER
CALL
OFF
VDP
DVD
1
2
3
TV/DBS
V.AUX
PHONO
4
5
VCR-1
CD
7
8
6
CHANNEL
9
TAPE-2 MON
+10
TV/VCR
0
A/B
VDP
2
(Main unit)
SHIFT
MD / TAPE-1
VCR-2
INPUT SELECTOR
RC-853
ON / SOURCE
TUNER
VOLUME
2
1
(Remote control unit)
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
AUDIO
DECK MD
CD
AVR/AVC
2 Set the input mode to “AUTO” or “DIGITAL”.
DISC SKIP+
HOME THX CINEMA
VIDEO
LOCK
DVD
MUTING
TV
VDP VCR
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
MENU/GUIDE
TITLE
BAND
5
INPUT MODE
INPUT MODE
ENTER
SELECT
MEMORY
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
USE/LEARN T.TONE
(Main unit)
2
6
(Remote control unit)
Select the Dolby Surround mode.
DOLBY / DTS
SURROUND
(Main unit)
3
4
CH SELECT
MODE
Play a program source with the
DOLBY / DTS
SURROUND
(Remote control unit)
,
mark.
• The Dolby Digital indicator lights when
Lit
playing Dolby Digital sources.
For operating instructions, refer to the
manuals of the respective components.
When the source is played, the input channel indicators
indicating the signals included in the source light as shown
on the diagram below. (The number of channels that lights
depends on the input source.)
L
CH INDICATOR
C
R
SL
S
SR
L:
C:
R:
SL:
S:
SR:
Front left channel
Center channel
Front right channel
Surround left channel
Mono surround channel
Surround right channel
• Also, the following indicator lights if the
software contains Low Frequency Effect
sounds:
LFE
Lit
Lit
The DTS indicator lights when playing DTS
sources.
45
Display the surround parameter
menu.
4
SURROUND
PARAMETER
MENU/GUIDE
5
6
Select the various parameters.
Enter the setting.
ENTER
NOTE:
• When “Default” is selected and the
cursor button is pressed, “CINEMA EQ.” and “D.COMP.” are automatically turned off, “LFE” is
reset, “S.Sp” is set to “A” and the tone is set to the default value.
Surround parameters 1
CINEMA EQ. (Cinema Equalizer):
The Cinema EQ function gently decreases the level of the extreme high frequencies, compensating for overly-bright sounding motion picture
soundtracks. Select this function if the sound from the front speakers is too bright.
This function only works in the Dolby Pro Logic, Dolby Digital and DTS Surround modes.
D.COMP. (Dynamic Range Compression):
Motion picture soundtracks have tremendous dynamic range (the contrast between very soft and very loud sounds). For listening late at night,
or whenever the maximum sound level is lower than usual, the Dynamic Range Compression allows you to hear all of the sounds in the
soundtrack (but with reduced dynamic range). (This only works when playing program sources recorded in Dolby Digital or DTS.) Select one of
the four parameters (“OFF”, “LOW”, “MID” (middle) or “HI” (high)). Set to OFF for normal listening.
LFE (Low Frequency Effect):
This sets the level of the LFE (Low Frequency Effect) sounds included in the source when playing program sources recorded in Dolby Digital
or DTS.
If the sound produced from the subwoofer sounds distorted due to the LFE signals when playing Dolby Digital or DTS sources when the peak
limiter is turned off with the subwoofer peak limit level setting (system setup menu), adjust the level as necessary.
Program source and adjustment range
1. Dolby Digital: –10 dB to 0 dB
2. DTS Surround (–10 dB to 0 dB)
(–10 dB to 0 dB for the DTS Surround Home THX Cinema mode)
2 When watching a DTS-encoded Movie program, we recommend that you set the LFE level at 0 dB. When THX is activated with a
DTS-encoded movie, the LFE level is automatically set to 0 dB. However, you can adjust it if you wish.
2 When listening to a DTS-encoded Music program, we recommend that you set the LFE level to –10 dB.
S.Sp (Surround Speaker):
Select the surround speaker to be used. This is not displayed if the surround speaker setting has been set to “None” in the system setup. It
is also not displayed in the direct or stereo modes.
TONE:
This adjusts the tone control. (See “Surround parameters 2” on page 51.)
2 Dialogue Normalization
The dialogue normalization function is activated automatically when playing Dolby Digital program sources.
Dialogue normalization is a basic function of Dolby Digital which automatically normalizes the dialog level (standard level) of the signals which are
recorded at different levels for different program sources, such as DVD, DTV and other future formats that will use Dolby Digital.
When this function is activated, the following message appears on the main unit’s display:
DIAL.NORM
OFFSET
46
- 4dB
The number indicates the normalization level when the currently playing program is normalized to
the standard level.
Home THX Cinema mode
[1] Playing sources recorded in Dolby Pro Logic in the Home THX Cinema surround mode
1
Select the Home THX Cinema mode.
HOME
THX CINEMA
(Main unit)
2
2
HOME THX CINEMA
(Remote control unit)
Play a program source with the
mark.
• For operating instructions, refer to the manuals of the
respective components.
7
8
9
VCR-2
TAPE-2 MON
+10
0
A/B
VOLUME
1
TV/VCR
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
AUDIO
DECK MD
CD
AVR/AVC
VIDEO
LOCK
DVD
MUTING
TV
VDP VCR
SYSTEM
SURROUND
[2] Playing sources recorded in Dolby Digital or DTS in the Home THX Cinema surround mode
1
Select the program source
2
Selecting the Dolby Digital input
Perform step 1 under “Dolby Digital mode and DTS
Surround” (page 45).
Selecting a digital input source
Perform step 1 under “Dolby Digital mode and DTS
Surround” (page 45).
2
Select the Home THX Cinema mode.
HOME
THX CINEMA
7
8
9
VCR-2
HOME THX CINEMA
TAPE-2 MON
+10
0
A/B
VOLUME
2
(Main unit)
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
(Remote control unit)
Play a program source with the
or
mark.
For operating instructions, refer to the manuals of the
respective components.
When the source is played, the input channel indicators
indicating the signals included in the source light as shown
on the diagram below. (The number of channels that lights
depends on the input source.)
L: Front left channel
CH INDICATOR
C: Center channel
L
C
R
R: Front right channel
SL: Surround left channel
SL
S
SR
S: Mono surround channel
SR: Surround right channel
• Also, the following indicator lights if the
software contains Low Frequency Effect
sounds:
Lit
DISC SKIP+
HOME THX CINEMA
AUDIO
3
TV/VCR
AVR/AVC
CD
VIDEO
DECK MD
LOCK
DVD
MUTING
TV
VDP VCR
SYSTEM
SURROUND
LFE
Lit
The DTS indicator lights when playing DTS
sources.
47
11 DSP SURROUND SIMULATION
• The AVR-5700 is equipped with a high performance DSP (Digital Signal Processor) which uses digital signal processing to synthetically
recreate the sound field. One of eight preset surround modes can be selected according to the program source and the parameters can be
adjusted according to the conditions in the listening room to achieve a more realistic, powerful sound. These surround modes can also be used
for program sources not recorded in Dolby Surround Pro Logic or Dolby Digital AC-3.
Surround modes and their features
1
SUPER STADIUM
Select this when watching baseball or soccer programs to achieve a sound as if you were actually at the stadium. This mode
provides the longest reverberation signals.
2
ROCK ARENA
Use this mode to achieve the feeling of a live concert in an arena with reflected sounds coming from all directions.
3
JAZZ CLUB
This mode creates the sound field of a live house with a low ceiling and hard walls. This mode gives jazz a very vivid realism.
4
CLASSIC CONCERT
Select this for the sound of a concert hall rich in reverberations.
5
MONO MOVIE
(NOTE 1)
Select this when watching monaural movies for a greater sense of expansion.
6
MATRIX
Select this to emphasize the sense of expansion for music sources recorded in stereo. Signals consisting of the difference
component of the input signals (the component that provides the sense of expansion) processed for delay are output from the
surround channel.
7
WIDE SCREEN
Select this to create the sense that you are watching the program source on a larger screen and in a place with more reflected
sound. This mode provides stronger reverberations for Dolby Digital and Dolby Pro Logic, and for DTS.
5CH STEREO
In this mode, the signals of the front left channel are output from the left surround channel, the signals of the front right channel
are output from the right surround channel, and the same (in-phase) component of the left and right channels is output from the
center channel. This mode provides all speaker surround sound, but without directional steering effects, and works with any
stereo program source
8
2
Depending on the program source being played, the effect may not be very noticeable.
In this case, try other surround modes, without worrying about their names, to create a sound field suited to your tastes.
NOTE 1: When playing sources recorded in monaural, the sound will be one-sided if signals are only input to one channel (left or right), so input
signals to both channels. If you have a source component with only one audio output (monophonic camcorder, etc.) obtain a “Y”
adaptor cable to split the mono output to two outputs, and connect to the L and R inputs.
NOTE:
Only the DIRECT and 5CH STEREO modes can be used when playing PCM signals with a sampling frequency of 96 kHz (such as from DVDVideo discs that contain 24 bit, 96 kHz audio). If such signals are input during playback in one of the other surround modes, the mode
automatically switches to DIRECT.
Personal Memory Plus
The AVR-5700 is equipped with a function called Personal Memory Plus which automatically stores the surround mode and level settings
selected for the different input programs in the memory. The mode stored in the memory the last time the input program source was used is
called out automatically when that program source is selected.
2 Items automatically stored for the different input program sources with the Personal Memory Plus function
1 Surround mode
2 Surround parameter
3 Playback level balance for the different output channels
4 Type and settings of surround channel speakers
5 Tone control
6 Input mode selection function
48
DSP surround simulation
1
Select the surround mode for the input channel.
DIRECT
STEREO
DOLBY / DTS
SURROUND
SURROUND MODE
WIDE
5CH
SCREEN
STEREO
DSP
SIMULATION
(Main unit)
DSP SIMULATION
DOLBY / DTS
SURROUND
DIRECT
5CH STEREO
STEREO
1
7
8
TAPE-2 MON
+10
The surround mode switches in the following order each
time the DSP SIMULATION button is pressed:
1 SUPER STADIUM
9
VCR-2
(Remote control unit)
1 ROCK ARENA
1 CLASSIC CONCERT
(WIDE SCREEN) 0
A/B
VOLUME
1 JAZZ CLUB
1 MONO MOVIE
TV/VCR
0
1
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
AUDIO
MATRIX 0
2
DISC SKIP+
HOME THX CINEMA
CD
AVR/AVC
VIDEO
DECK MD
LOCK
DVD
MUTING
TV
VDP VCR
2
“WIDE SCREEN” can only be selected from the main
unit.
TUNING
SURROUND
PARAMETER
MENU/GUIDE
TITLE
3
2,4
CH SELECT
ENTER
MODE
SELECT
MEMORY
USE/LEARN T.TONE
2
SYSTEM
SETUP
BAND
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
Display the surround parameter screen on the monitor.
2 The screen for the selected surround mode appears.
SURROUND
PARAMETER
MENU/GUIDE
Set the parameters.
3
4
To end the setting mode, press the surround parameter button again.
SURROUND
PARAMETER
MENU/GUIDE
NOTES:
• When “Default” is selected and the
cursor button is pressed, “CINEMA EQ.” and “D.COMP.” are automatically turned off, “ROOM
SIZE” is set to “medium”, “EFFECT LEVEL” to “10” and “DELAY TIME” to “30ms”.
• The “ROOM SIZE” expresses the expansion effect for the different surround modes in terms of the size of the sound field, not the actual
size of the listening room.
49
Tone control setting
• Use the tone control setting to adjust the bass and treble as desired.
1
SURROUND
PARAMETER
MENU/GUIDE
Display the surround parameter
screen on the monitor.
2 The screen for the selected
surround mode appears.
“TONE” cannot be selected in
the Direct or Home THX Cinema
mode.
START
SYSTEM CALL
SET
LEARNED/TX
POWER
CALL
DVD
OFF
VDP
1
2
3
TV/DBS
V.AUX
PHONO
4
5
VCR-1
CD
7
8
2
SHIFT
6
MD / TAPE-1
CHANNEL
9
VCR-2
TAPE-2 MON
+10
RC-853
ON / SOURCE
TUNER
TV/VCR
0
A/B
Select “TONE”.
VOLUME
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
AUDIO
CD
AVR/AVC
VIDEO
DECK MD
LOCK
DVD
MUTING
TV
VDP VCR
SYSTEM
SETUP
TUNING
SURROUND
PARAMETER
MENU/GUIDE
TITLE
BAND
2,4
3
Switch to the Tone Control screen.
ENTER
SELECT
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
MEMORY
USE/LEARN T.TONE
ENTER
4
5
6
o
To select Bass or Treble.
ENTER
To set the level.
2
If you do not want the tone to be adjusted, set “Tone Defeat” to “ON”.
(See page 39.)
Enter the setting.
The surround menu screen re-appears.
To end the setting mode, press the surround parameter button again.
SURROUND
PARAMETER
MENU/GUIDE
50
o
1,6
CH SELECT
MODE
3,5
Surround parameters 2
ROOM SIZE:
This sets the size of the sound field.
There are five settings: “small”, “med.s” (medium-small), “medium”, “med.l” (medium-large) and “large”. “small” recreates a small sound
field, “large” a large sound field.
EFFECT LEVEL:
This sets the strength of the surround effect.
The level can be set in 15 steps from 1 to 15. Lower the level if the sound seems distorted.
DELAY TIME:
In the matrix mode only, the delay time can be set within the range of 0 to 300 ms.
TONE CONTROL:
This can be set individually for the separate surround modes other than Direct and Home THX Cinema.
2 Surround modes and parameters
Signals and adjustability in the different modes
Channel output
Parameter (default values are shown in parentheses)
When playing Dolby
Digital and DTS signals
FRONT
L/R
CENTER
SURROUND
L/R
SUBWOOFER
EFFECT
L/R
TONE
CONTROL
CINEMA
EQ.
ROOM
SIZE
EFFECT
LEVEL
DELAY
TIME
D.COMP.
LFE
DIRECT
A
E
E
o
E
E
E
E
E
E
A (OFF)
A (0dB)
STEREO
A
E
E
o
E
A (0dB)
E
E
E
E
A (OFF)
A (0dB)
6CH/8CH EXTERNAL INPUT
A
o
o
o
A
A (0dB)
E
E
E
E
E
E
WIDE SCREEN
A
o
o
o
E
A (0dB)
A (OFF)
A (Medium)
A (10)
E
A (OFF)
A (0dB)
DOLBY PRO LOGIC
A
(THX CINEMA ON)
A
o
o
o
E
E
E
E
E
E
A (OFF)
A (0dB)
(THX CINEMA OFF)
A
o
o
o
E
A (0dB)
A (OFF)
E
E
E
A (OFF)
A (0dB)
(THX CINEMA ON)
A
o
o
o
E
E
E
E
E
E
A (OFF)
A (0dB)
(THX CINEMA OFF)
A
o
o
o
E
A (0dB)
A (OFF)
E
E
E
A (OFF)
A (0dB)
(THX CINEMA ON)
A
o
o
o
E
E
E
E
E
E
A (OFF)
A (0dB)
(THX CINEMA OFF)
A
o
o
o
E
A (0dB)
A (OFF)
E
E
E
A (OFF)
A (0dB)
5CH STEREO
A
o
o
o
E
A (0dB)
E
E
E
E
A (OFF)
A (0dB)
SUPER STADIUM
A
o
o
o
E
A (note 1)
E
A (Medium)
A (10)
E
A (OFF)
A (0dB)
ROCK ARENA
A
o
o
o
E
A (note 2)
E
A (Medium)
A (10)
E
A (OFF)
A (0dB)
JAZZ CLUB
A
o
o
o
E
A (0dB)
E
A (Medium)
A (10)
E
A (OFF)
A (0dB)
CLASSIC CONCERT
A
o
o
o
E
A (0dB)
E
A (Medium)
A (10)
E
A (OFF)
A (0dB)
MONO MOVIE
A
o
o
o
E
A (0dB)
E
A (Medium)
A (10)
E
A (OFF)
A (0dB)
MATRIX
A
o
o
o
E
A (0dB)
E
E
E
A (30msec)
A (OFF)
A (0dB)
Mode
DOLBY DIGITAL AC-3
DTS SURROUND
A : Signal/adjustable
C : Selected by speaker configuration setting
(Note 1) BASS: +6dB, TREBLE: 0dB
(Note 2) BASS: +8dB, TREBLE: +4dB
o:
E:
Turned on or off by speaker configuration setting
No signal/not adjustable
51
12 LISTENING TO THE RADIO
Auto tuning
1
Set the input function to “TUNER”.
INPUT SELECTOR
1
TUNER
3
(Main unit)
2
(Remote control unit)
Watching the display, press the BAND button to select the
desired band (AM or FM).
BAND
START
SYSTEM CALL
SET
3
Press the MODE button to set the auto tuning mode.
LEARNED/TX
POWER
CALL
OFF
VDP
DVD
1
2
3
TV/DBS
V.AUX
PHONO
4
5
6
VCR-1
CD
MD / TAPE-1
7
8
SHIFT
1
CHANNEL
9
VCR-2
TAPE-2 MON
+10
TV/VCR
0
A/B
VOLUME
MODE
“Auto” appears on the display.
RC-853
ON / SOURCE
TUNER
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
AUDIO
CD
AVR/AVC
4
4
2
3
Press the TUNING UP or DOWN button.
TUNING
Automatic searching begins, then
stops when a station is tuned in.
VIDEO
DECK MD
LOCK
DVD
MUTING
TV
VDP VCR
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
MENU/GUIDE
TITLE
BAND
CH SELECT
ENTER
MODE
SELECT
MEMORY
USE/LEARN T.TONE
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
If tuning does not stop at the desired station, use to the “Manual
tuning” operation.
Manual tuning
1
Set the input function to “TUNER”.
INPUT SELECTOR
3
TUNER
MODE
3
(Main unit)
2
Press the MODE button to set the manual tuning mode.
Check that the display’s “AUTO” indicator turns.
(Remote control unit)
Watching the display, press the BAND button to select the
desired band (AM or FM).
BAND
4
Press the TUNING UP or DOWN button to tune in the desired station.
The frequency changes continuously when the button is held
in.
TUNING
NOTES:
• When in the auto tuning mode on the FM band, the “STEREO” indicator lights on the display when a stereo broadcast is tuned in. At open
frequencies, the noise is muted and the “TUNED” and “STEREO” indicators turn off.
• When the manual tuning mode is set, FM stereo broadcasts are received in monaural and the “STEREO” indicator turns off.
52
Preset memory
1
2
3 4
Use the “Auto tuning” or “Manual tuning” operation to tune
in the station to be preset in the memory.
Press the MEMORY button.
MEMORY
3
Press the SHIFT button and select the desired memory block (A to D).
START
SYSTEM CALL
SHIFT
SET
SHIFT
LEARNED/TX
POWER
CALL
OFF
VDP
DVD
1
2
3
TV/DBS
V.AUX
PHONO
4
5
6
VCR-1
CD
7
8
4
(Remote control unit)
DOWN
CHANNEL
9
TAPE-2 MON
+10
Press the PRESET UP or DOWN button to select the desired
preset channel (1 to 8).
SHIFT
MD / TAPE-1
VCR-2
(Main unit)
3
4
TV/VCR
0
A/B
VOLUME
UP
RC-853
ON / SOURCE
TUNER
DISC SKIP+
HOME THX CINEMA
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO
STEREO
INPUT MODE
ANALOG
EXT.IN
MASTER VOL.
CHANNEL
AUDIO
CD
AVR/AVC
VIDEO
DECK MD
LOCK
DVD
MUTING
TV
VDP VCR
TUNING
SYSTEM
SETUP
SURROUND
PARAMETER
TITLE
MENU/GUIDE
BAND
(Main unit)
(Remote control unit)
CH SELECT
ENTER
MODE
SELECT
5
Press the MEMORY button again to store the station in the
preset memory.
MEMORY
2,5
USE/LEARN T.TONE
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
MEMORY
To preset other channels, repeat steps 2 to 5.
A total of 40 broadcast stations can be preset — 8 stations
(channels 1 to 8) in each of blocks A to E.
Checking the preset stations
The preset broadcast stations can be checked on the on screen display.
1
Press the ON SCREEN button repeatedly until the “Tuner Preset Stations” screen appears on
the on screen display.
AVR/AVC
VIDEO
DVD
TV
VDP VCR
TUNING
ON SCREEN
SYSTEM
SETUP
CH SELECT
ENTER
MODE
RETURN
SURROUND
PARAMETER
MENU/GUIDE
TITLE
BAND
SELECT
MEMORY
USE/LEARN T.TONE
PANEL
ON SCREEN
DISPLAY
RETURN
MULTI
DVD
SET UP
1
53
Recalling preset stations
1
Watching the display, press the SHIFT button to select the
preset memory block.
SHIFT
SHIFT
(Main unit)
2
1 2
(Remote control unit)
Watching the display, press the PRESET UP or DOWN
button to select the desired preset channel.
DOWN
UP
START
SYSTEM CALL
CHANNEL
SET
CALL
VDP
DVD
(Main unit)
(Remote control unit)
LEARNED/TX
POWER
OFF
TUNER
1
2
3
TV/DBS
V.AUX
PHONO
4
5
6
VCR-1
CD
7
8
VCR-2
MD / TAPE-1
0
VOLUME
SHIFT
CHANNEL
9
TAPE-2 MON
+10
RC-853
ON / SOURCE
1
2
TV/VCR
A/B
DISC SKIP+
DOLBY / DTS
13 LAST FUNCTION MEMORY
• This unit is equipped with a last function memory which stores the input and output setting conditions as they were immediately before the
power is switched off.
This function eliminates the need to perform complicated resettings when the power is switched on.
• The unit is also equipped with a back-up memory. This function provides approximately one week of memory storage when the main unit’s
power switch is off and with the power cord disconnected.
14 INITIALIZATION OF THE MICROPROCESSOR
When the indication of the display is not normal or when the operation of the unit does not shows the reasonable result, the initialization of the
microprocessor is required by the following procedure.
1
2
3
Switch off the unit using the main unit’s power switch.
Hold the following DIRECT button and STEREO button, and
turn the main unit’s power switch on.
Check that the entire display is flashing with an interval of
about 1 second, and release your fingers from the 2 buttons
and the microprocessor will be initialized.
NOTES:
• If step 3 does not work, start over from step 1.
• If the microprocessor has been reset, all the button settings are
reset to the default values (the values set upon shipment from
the factory).
54
1,2
2
Lightly press on the button
of the door to open it.
15 TROUBLESHOOTING
If a problem should arise,first check the following.
1. Are the connections correct ?
2. Have you operated the receiver according to the Operating Instructions ?
3. Are the speakers, turntable and other components operating property ?
If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there may be a malfunction.
Disconnect the power immediately and contact your store of purchase.
Remote control unit.
When playing records
Common problems arising when listening to the CD, records, tapes, and FM broadcasts, etc.
Symptom
DISPLAY not lit and sound not produced
when power switch set to on.
DISPLAY lit but sound not produced.
Measures
Page
• Power cord not plugged in securely.
• Check the insertion of the power cord plug.
• Turn the power on with the remote control
unit after turning the POWER switch on.
6
36
• Speaker cords not securely connected.
• Improper position of the audio function
button.
• Volume control set to minimum.
• MUTING is on.
• Digital signals not input Digital input
selected.
• Connect securely.
• Set to a suitable position.
12
37
• Turn volume up to suitable level.
• Switch off MUTING.
• Input digital signals or select input jacks to
which digital signals are being input.
38
39
37
• Speaker terminals are short-circuited.
• Switch power off, connect speakers
properly, then switch power back on.
• Turn off the set’s power, then ventilate it
well to cool it down.
Once the set is cooled down, turn the
power back on.
• Turn off the set’s power, then ventilate it
well to cool it down.
Once the set is cooled down, turn the
power back on.
12
Cause
• Block the ventilation holes of the set.
DISPLAY not lit and power indicator is
flashing rapidly.
• The unit is operating at continuous high
power conditions and/or inadequate
ventilation.
4, 5
4, 5
12
6 ~ 13
Sound produced only from one channel.
• Incomplete connection of speaker cords.
• Incomplete connection of input/output
cords.
• Connect securely.
• Connect securely.
Positions of instruments reversed during
stereo playback.
• Reverse connections of left and right
speakers or left and right input/output
cords.
• Check left and right connections.
The on screen display is not displayed.
• “On screen display” is set to off on the
system setup menu screen.
• Set “on screen display” on the system
setup menu screen to on.
• Ground wire of turntable not connected
properly.
• Incomplete PHONO jack connection.
• TV or radio transmission antenna nearby.
• Connect securely.
6
Humming noise produced when record
is playing.
• Connect securely.
• Contact your store of purchase.
6
—
• Turntable and speaker systems too close
together.
• Floor is unstable and vibrates easily.
• Separate as much as possible.
—
• Use cushions to absorb speaker vibrations
transmitted by floor. If turntable is not
equipped with insulators, use audio
insulators (commonly available).
—
Sound is distorted.
• Stylus pressure too weak.
• Dust or dirt on stylus.
• Cartridge defective.
• Apply proper stylus pressure.
• Check stylus.
• Replace cartridge.
—
—
—
Volume is weak.
• MC cartridge being used.
• Replace with MM cartridge or use a head
amplifier or step-up transformer.
6
This unit does not operate properly
when remote control unit is used.
• Batteries dead.
• Remote control unit too far from this unit.
• Obstacle between this unit and remote
control unit.
• Different button is being pressed.
• < and > ends of battery inserted in
reverse.
• Replace with new batteries.
• Move closer.
• Remove obstacle.
28
28
28
• Press the proper button.
• Insert batteries properly.
—
28
Howling noise produced when volume is
high.
12
26, 27
55
16 ADDITIONAL INFORMATION
Optimum surround sound for different sources
There are currently various types of multi-channel signals (signals or formats with more than two channels).
2 Types of multi-channel signals
Dolby Digital, Dolby Pro Logic, DTS, high definition 3-1 signals (Japan MUSE Hi-Vision audio), DVD-Audio, SACD (Super Audio CD), MPEG
multi-channel audio, etc.
“Source” here does not refer to the type of signal (format) but the recorded content. Sources can be divided into two major categories.
2 Types of sources
• Movie audio
Signals created to be played in movie theaters. In general sound is recorded to be played in movie theaters equipped
with multiple surround speakers, regardless of the format (Dolby Digital, DTS, etc.).
Movie theater sound field
FL
SW
C
FR
Listening room sound field
FL
SW
SL
SL
C
FR
SR
In this case it is important to achieve the same sense of
expansion as in a movie theater with the surround channels.
To do so, in some cases the number of surround speakers is
increased (to four or eight) or speakers with bipolar or dipolar
properties are used.
SR
Multiple surround speakers
• Other types of audio These signals are designed to recreate a 360° sound field using three to five speakers.
FL
SW
C
FR
In this case the speakers should surround the listener from all sides to create a uniform sound
field from 360°. Ideally the surround speakers should function as “point” sound sources in the
same way as the front speakers.
SL
SR
These two types of sources thus have different properties, and different speaker settings, particularly for the surround speakers, are required
in order to achieve the ideal sound.
The AVR-5700’s surround speaker selection function makes it possible to change the settings according to the combination of surround
speakers being used and the surrounding environment in order to achieve the ideal surround sound for all sources. This means that you can
connect a pair of bipolar or dipolar surround speakers (mounted on either side of the prime listening position), as well as a separate pair of
direct radiating (monopolar) speakers placed at the rear corners of the listening room.
56
Speaker setting examples
Here we describe a number of speaker settings for different purposes. Use these examples as guides to set up your system according to the
type of speakers used and the main usage purpose.
(1) Basic setting for primarily watching movies
Use this setting if your main purpose is to listen to movie music and when using one set (two speakers) of regular single-way or two-way
speakers as the surround speakers.
Front speakers
Center speaker
Monitor
Subwoofer
45°
• Set the front speakers with their front surfaces as flush with the TV or
monitor screen as possible. Set the center speaker between the front left
and right speakers and no further from the listening position than the front
speakers.
• Consult the owner’s manual for your subwoofer for advice on placing the
subwoofer within the listening room.
• If the surround speakers are direct-radiating (monopolar) then place them
slightly behind and at an angle to the listening position and parallel to the
walls at a position 60 to 90 centimeters (2 to 3 feet) above ear level at the
prime listening position.
• Connect the surround speakers to the surround speaker A jacks on the
AVR-5700 and set all settings on the setup menu to “A”. (This is the
factory default setting. For details, see page 16.)
Surround speaker
Front speaker
60 to 90 cm
As seen from the side
120°
Surround speakers
As seen from above
(2) Setting for primarily watching movies using diffusion type speakers for the surround speakers
For the greatest sense of surround sound envelopment, diffuse radiation speakers such as bipolar types, or dipolar (THX) types, provide a
wider dispersion than is possible to obtain from a direct radiating speaker (monopolar). Place these speakers at either side of the prime
listening position, mounted above ear level.
Path of the surround sound from the
speakers to the listening position
• Set the front speakers, center speaker and subwoofer in the same
Surround speaker
positions as in example (1).
• Set the surround speakers directly at the sides of the listening position
Front speaker
and 60 to 90 centimeters (2 to 3 feet) above ear level.
• Connect the surround speakers to the surround speaker A jacks on the
60 to 90 cm
AVR-5700 and set all settings on the setup menu to “A”. (This is the
factory default setting. For details, see page 16.)
• The signals from the surround channels reflect off the walls as shown on
the diagram at the left, creating an enveloping and realistic surround sound
presentation.
As seen from the side
For multi-channel music sources however, the use of bipolar or dipolar
speakers mounted at the sides of the listening position may not be satifactory in order to create a coherent 360 degree
surround sound field. Connect another pair of direct radiating speakers as described in example (3) and place them at
the rear corners of the room facing towards the prime listening position.
As seen from above
(3) When using different surround speakers for movies and music
To achieve more effective surround sound for both movies and music, use different sets of surround speakers and different surround modes
for the two types of sources.
Front speakers
Center speaker
Monitor
Subwoofer
45° ~ 60°
140°
Surround speakers B
Surround speakers A
As seen from above
• Set the front speakers slightly wider apart than the setup for watching movies only and point them toward the listening
position in order assure clear positioning of the sound.
• Set the center speaker in the same positions as in example (1).
• Set surround speakers A for watching movies in the positions described in example (1) or (2), depending on the types
of speakers used.
• Set surround speakers B for playing multi-channel music at the same height as the front speakers and slightly at an
angle to the rear of the listening position, and point them toward the listening position.
• Connect the surround speakers for watching movies to the surround speaker A jacks on the AVR-5700, the surround
speakers for playing multi-channel music to the surround speaker B jacks. Set the surround speaker selection on the
setup menu. (For instructions, see page 18.)
• To activate the appropriate speakers for movies and music, we suggest that during setup, choose Dolby Digital/DTS
with THX and Surround Speakers A (the bipolar or dipolar speakers mounted at the sides of the listening position).
Choose Dolby Digital/DTS without THX and Surround Speakers B (the
direct radiating speakers mounted at the rear corners of the listening
Surround speakers A
room). Then, by simply activating the THX function (used during movie
playback, the Surround A speakers are automatically activated. For multiFront speaker
Surround
channel music listening (Dolby Digital or DTS music programs), turn off the
speakers B
60 to 90 cm
THX enhancements by touching the THX button on the remote control,
and the Surround B speakers will be automatically activated.
Example: Movie sources (Dolby, DTS surround, etc.)
“THX” or “THX 5.1” mode: Speakers A
Music sources (DVD video, DTS CD, etc.)
As seen from the side
“Dolby/DTS surround”: Speakers B
2 The speakers can be switched at the touch of a button by turning HOME THX CINEMA on when playing movies and off when playing multi-channel music.
The surround speakers can be switched freely during playback with the surround parameter adjustment. (For instructions, see page 46.)
57
Surround
The AVR-5700 is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the same
sense of presence as in a movie theater.
Dolby Surround
(1) Dolby Digital (Dolby Surround AC-3)
Dolby Digital is the multi-channel digital signal format developed by Dolby Laboratories.
Dolby Digital consists of up to “5.1” channels - front left, front right, center, surround left, surround right, and an additional channel
exclusively reserved for additional deep bass sound effects (the Low Frequency Effects – LFE – channel, also called the “.1” channel,
containing bass frequencies of up to 120 Hz).
Unlike the analog Dolby Pro Logic format, Dolby Digital’s main channels can all contain full range sound information, from the lowest bass, up
to the highest frequencies – 22 kHz. The signals within each channel are distinct from the others, allowing pinpoint sound imaging, and Dolby
Digital offers tremendous dynamic range from the most powerful sound effects to the quietest, softest sounds, free from noise and
distortion.
2 Dolby Digital and Dolby Pro Logic
Comparison of home surround systems
Dolby Digital
Dolby Pro Logic
No. recorded channels (elements)
5.1 ch
2 ch
No. playback channels
5.1 ch
4 ch
L, R, C, SL, SR, SW
L, R, C, S (SW - recommended)
Digital discrete processing Dolby Digital (AC-3) encoding/decoding
Analog matrix processing Dolby Surround
20 kHz
7 kHz
Playback channels (max.)
Audio processing
High frequency playback limit of surround
channel
2 Dolby Digital compatible media and playback methods
Marks indicating Dolby Digital compatibility:
and
.
The following are general examples. Also refer to the player’s operating instructions.
Media
Dolby Digital output jacks
Playback method (reference page)
LD (VDP)
21 22 23
Coaxial Dolby Digital RF output jack
21 22 23
Set the input mode to “AUTO” or “RF”.
(Page 37)
DVD
22
Optical or coaxial digital output
(same as for PCM)
24
Set the input mode to “AUTO” or “DIGITAL”.
(Page 37)
Others
(satellite broadcasts, CATV, etc.)
Optical or coaxial digital output
(same as for PCM)
Set the input mode to “AUTO” or “DIGITAL”.
(Page 37)
1 When playing in Dolby Digital with a Dolby Digital compatible LD player, connect the LD (VDP) player to the VDP function. (See page 25.)
2 When the LD/DVD compatible player is equipped with Dolby Digital RF outputs, the LD’s Dolby Digital output is output from the RF jacks
and the DVD’s Dolby Digital output is output from the optical or coaxial digital jacks. Select the input mode according to the type of media
being played (LD or DVD). Also, if both the RF and Digital outputs are connected to the AVR-5700’s VDP function, the input mode can be
selected automatically by setting the “AUTO” mode (see page 45).
2 3 If the player is switched from the pause or search mode to the play mode when playing an LD in the “AUTO” mode (see page 37), analog
sound may be output momentarily before the sound switches to Dolby Digital. This is because the Dolby Digital RF signals output from the
LD are not output during the pause and search modes, so during this type the input mode is switched according to the “AUTO” mode’s
signal priority order (see page 37). If this happens, switch to the “RF” (fixed RF input) mode. No analog sound will be output.
2 4 Some DVD digital outputs have the function of switching the Dolby Digital signal output method between “bit stream” and “(convert to)
PCM”. When playing in Dolby Digital surround on the AVR-5700, switch the DVD player’s output mode to “bit stream”. In some cases
players are equipped with both “bit stream + PCM” and “PCM only” digital outputs. In this case connect the “bit stream + PCM” jacks to
the AVR-5700.
2
2
58
(2) Dolby Pro Logic
Dolby Pro Logic is a multi-channel signal playback system developed by Dolby Laboratories which decodes sources recorded in Dolby
Surround into four channels: front left, center, front right and surround (the surround channel is monaural, but is played through two surround
speakers). Here, “sources recorded in Dolby Surround” are sources on which surround signals (three channels or more) are recorded onto
two channels using Dolby Surround encoding technology. Dolby Surround recording is possible for all two-channel signal sources, including
soundtracks on DVDs (2), LDs or hi-fi VCRs (for which stereo signal recording is possible), stereo FM, TV and satellite broadcasts, stereo CD,
MD and analog cassette tape recordings. Sources recorded in Dolby Surround are compatible with stereo playback, so they can be played in
stereo on regular stereo equipment and in surround with Dolby Pro Logic processing. (DTS and Dolby Digital require special decoders to be
played.)
With Dolby Pro Logic, the signal levels of the different channels of the source recorded in Dolby Surround are monitored, channels with
higher signal levels are emphasized and the level of the other channels is decreased in order to reinforce the directivity and achieve an
effective surround sound.
2 DVDs recorded in Dolby Surround include sources recorded in PCM and sources recorded in 2-channel Dolby Digital. For 2-channel Dolby
Digital DVD sources, the DVD player’s audio mode is 2-channel Dolby Digital, and the AVR-5700’s surround mode is Dolby Pro Logic. Use
the display pattern of the channel indicators (see page 45) to check whether the Dolby Digital signals are recorded in 2-channel stereo or
Dolby Surround.
2 Dolby Pro Logic compatible media and playback methods
Mark indicating Dolby Pro Logic compatibility:
When playing in Dolby Pro Logic, select the input signal according to how the player is connected to the AVR-5700, in the same way as
selecting the stereo signal (see page 25). Set the surround mode to “DOLBY SURROUND” (see page 44) to play in Dolby Pro Logic.
Manufactured on license of the Dolby Laboratories Licensing Corporation.
“Dolby”, “Pro Logic” and the double D mark are registered trademarks of the Dolby Laboratories Licensing Corporation.
Confidential and secret copyrighted material. Copyright 1992-1997, Dolby Laboratories Incorporated. Copying prohibited.
DTS Digital Surround
Digital Theater Surround (also called simply DTS) is a multi-channel digital signal format developed by Digital Theater Systems.
DTS offers the same “5.1” playback channels as Dolby Digital (front left, front right and center, surround left and surround right) as well as the
stereo 2-channel mode. The signals for the different channels are fully independent, eliminating the risk of deterioration of sound quality due to
interference between signals, crosstalk, etc.
DTS features a relatively higher bit rate as compared to Dolby Digital (1234 kbps for CDs and LDs, 1536 kbps for DVDs) so it operates with a
relatively low compression rate. Because of this the amount of data is great, and when DTS playback is used in movie theaters, a separate CDROM synchronized with the film is played.
With LDs and DVDs, there is of course no need for an extra disc; the pictures and sound can be recorded simultaneously on the same disc, so
the discs can be handled in the same way as discs with other formats.
There are also music CDs recorded in DTS. These CDs include 5.1-channel surround signals (compared to two channels on current CDs). They do
not include picture data, but they offer surround playback on CD players that are equipped with digital outputs (PCM type digital output required).
DTS surround track playback offers the same intricate, grand sound as in a movie theater, right in your own listening room.
2 DTS compatible media and playback methods
Marks indicating DTS compatibility:
and
.
The following are general examples. Also refer to the player’s operating instructions.
Media
Dolby Digital output jacks
Playback method (reference page)
CD
Optical or coaxial digital output
(same as for PCM) 2 2
Set the input mode to “AUTO” or “DIGITAL” (page 37).
Never set the mode to “ANALOG” or “PCM”. 2 1
LD (VDP)
Optical or coaxial digital output
(same as for PCM) 2 2
Set the input mode to “AUTO” or “DIGITAL” (page 37).
Never set the mode to “ANALOG” or “PCM”. 2 1
DVD
Optical or coaxial digital output
(same as for PCM) 2 3
Set the input mode to “AUTO” or “DIGITAL” (page 37).
1 DTS signals are recorded in the same way on CDs and LDs as PCM signals. Because of this, the un-decoded DTS signals are output as
random “hissy” noise from the CD or LD player’s analog outputs. If this noise is played with the amplifier set at a very high volume, it may
possibly cause damage to the speakers. To avoid this, be sure to switch the input mode to “AUTO” or “DIGITAL” before playing CDs or
LDs recorded in DTS. Also, never switch the input mode to “ANALOG” or “PCM” during playback. The same holds true when playing
CDs or LDs on a DVD player or LD/DVD compatible player. For DVDs, the DTS signals are recorded in a special way so this problem does
not occur.
2 2 The signals provided at the digital outputs of a CD or LD player may undergo some sort of internal signal processing (output level
adjustment, sampling frequency conversion, etc.). In this case the DTS-encoded signals may be processed erroneously, in which case
they cannot be decoded by the AVR-5700, or may only produce noise. Before playing DTS signals for the first time, turn down the master
volume to a low level, start playing the DTS disc, then check whether the DTS indicator on the AVR-5700 (see page 45) lights before
turning up the master volume.
2 3 A DVD player with DTS-compatible digital output is required to play DTS DVDs. A DTS Digital Output logo is featured on the front panel of
compatible DVD players. Recent DENON DVD player models feature DTS-compatible digital output – consult the player’s owner’s manual
for information on configuring the digital output for DTS playback of DTS-encoded DVDs.
2
Manufactured under license of Digital Theater Systems.
“DTS” and “DTS Digital Surround” are trademarks of Digital Theater Systems.
59
Home THX Cinema surround mode
Home THX Cinema is a surround playback technology advocated by Lucasfilm of the United States, a company famous for the sound effects of
such movies as Star Wars and Indiana Jones. This technology was born from the desire of movie director George Lucas to create the ultimate
theater experience. THX Cinema technology includes both a design and performance certification program for movie theaters and a separate
design and certificatioin program for home theater equipment.
The THX Cinema program for theaters is used in over 3000 movie theaters throughout the world and is highly reputed for both its sound and
picture quality.
The Home THX program includes proprietary Lucasfilm technology, coupled with an extensive certification process, which provides the listener
with the most realistic reproduction in the home of motion picture soundtracks. Differences between the dubbing stage (sound mixing
environment) and the motion picture theater are compensated for in home playback environments by the unique THX post-processing functions.
THX is not a multi-channel encoding/decoding system (like Dolby Digital or DTS), but is a set of functions that enhance and improve upon the
multi-channel decoded audio program material. So, for the best motion picture surround sound reproduction, choose THX with Dolby Digital,
Dolby Surround Pro Logic or DTS. The THX processing can be de-activated at the touch of a button when listening to non-movie surround sound
programs, such as music concerts, etc.
“THX 5.1” indicates the combination of a digital discrete multi-channel motion picture soundtrack as well as the specific THX multi-channel audio
post-processing.
DENON was the first company in the world to offer THX 5.1 processing in a home theater component. The AVR-5700 is the world’s first A/V
receiver that incorporates the ability to have THX 5.1 surround sound with either Dolby Digital or DTS encoded programs.
The THX processor achieves clear dialogue, more effective sound positioning and directivity and a wide dynamic range. On the AVR-5700, when
the Home THX Cinema mode is turned on, THX processing is automatically added after signal processing by the Dolby Digital, DTS, or Dolby Pro
Logic decoder. The THX processing consists of the main components described below.
(1) Re-equalizer:
In general, sound for movie theaters is recorded under the premise that the front and center channels will be output from behind the screen
and that the sound will be played in large spaces that include many objects that absorb sound (movie theater seats, etc.). Because of this, the
sound characteristics, particular the high frequency response, differs when the same soundtrack is played in the home (it can sound overly
bright and harsh). The re-equalizer is a circuit that provides the compensation necessary to achieve natural high frequency sound in the home
that matches that heard in the movie theater.
(2) Timber matching circuit:
The human ear is directional, so the sound from a speaker set in front of the listener will seem different from the sound from the same
speaker set at the listener’s side. The timber matching circuit compensates for this, and particularly provides a natural sense of movement
when the sound moves from the front to the surround and vice versa.
(3) Dynamic decorrelation circuit:
In movie theaters, surround signals come from two banks of surround speakers, placed at the sides and at the rear of the theater. By using
multiple loudspeakers in each surround bank, the audience hears the intended surround effect regardless of where they sit in the theater.
Even with 5.1 soundtracks, surround sound information in the motion picture soundtrack is often monaural (sounds are common to both
surround left and surround right channels). In the theater, the use of many surround speakers “spreads” the surround information over a wide
area, minimizing the ability to localize the sound from a particular speaker. In the home however, monaural information in the soundtrack
often provides an unusual result, with the surround sound strongly localized directly at the listening position, and is not perceived as
enveloping, spacious surround sound as heard in the theater. The dynamic decorrelation circuit constantly monitors the content of the
surround channels, and when monaural surround information is present, processes the sound to derive different signals that are sent to the
left and right surround speakers. This provides rich, spacious and enveloping surround sound. The decorrelation circuit is always activated
when listening to Dolby Surround Pro Logic programs, since the Pro Logic surround channel is always monaural.
THX 5.1 standards are extremely strict performance standards for AV amplifiers. Over 300 different performance parameters are checked,
covering virtually all aspects of the component’s performance, including use and operation, along with critical tests and measurements using
specialized test tones along with highly revealing program material. The AVR-5700 is certified compliant with THX-ULTRA, Lucasfilm’s strictest
standards, a sign of quality assurance indicating that it offers the ultimate home theater performance and sound quality.
“Lucasfilm” and “THX” are registered trademarks of Lucasfilm.
This set manufactured under license of Lucasfilm.
60
System setup items and default values (set upon shipment from the factory)
System setup
Default settings
Speaker
Configuration
Input the combination of speakers in your system and their
corresponding sizes (SMALL for regular speakers, LARGE for fullsize, full-range) to automatically set the composition of the signals
output from the speakers and the frequency response.
(Surround
Speaker
Setting)
Use this function when using multiple surround speaker
combinations for more ideal surround sound. Once the
combinations of surround speakers to be used for the
different surround modes are preset, the surround
speakers are selected automatically according to the
surround mode.
1
Small
Small
DOLBY/
DTS
SURROUND
THX
SURROUND
WIDE
SCREEN
Surround
speaker
A
A
A
Bass Output
This selects the subwoofer speaker for playing deep bass signals.
3
Delay Time
This parameter is for optimizing the timing with which the audio
signals are produced from the speakers and subwoofer according to
the listening position.
4
Channel
Level
This adjusts the volume of the signals output from the speakers and
subwoofer for the different channels in order to obtain optimum
effects.
5
Subwoofer
Peak Limit
Lev
This parameter is for detecting the maximum level of the low bass
signals output from the subwoofer channel in order to protect the
subwoofer from damage and prevent unpleasant distorted sounds
from being produced.
6
Digital Inputs
This assigns the digital input jacks for the different input
sources.
7
On Screen
Display
Auto Tuner
Presets
Center Sp.
Surround
mode
2
8
Front Sp.
Surround Sp.
Sub Woofer
Small
Yes
5CH
STEREO
DSP
SIMULATION
6CH
EXT. IN
—
—
A
A
A
—
—
Bass Out = Subwoofer Only THX
Front L & R
Center
Surround L & R
Sub Woofer
3.6 m (12 ft)
3.6 m (12 ft)
3.0 m (10 ft)
3.6 m (12 ft)
Front L
Front R
Center
Surround
L
Surround
R
Subwoofer
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
Peak Limitter = OFF
Input
source
CD
DVD
VDP
TV/DBS
VCR-1
VCR-2
V.AUX
TAPE-1
Digital
Inputs
COAXIAL
1
COAXIAL
2
COAXIAL
3
OPTICAL
1
OPTICAL
2
OPTICAL
3
OPTICAL
4
OPTICAL
5
This sets whether or not to display the on-screen display that
appears on the monitor screen when the controls on the remote
control unit or main unit are operated(from MONITOR 1 outputs
only).
FM stations are received automatically and stored in the memory.
On Screen Display = ON
A1 ~ A8
87.5/89.1/98.1/107.9/90.1/90.1/90.1/90.1 MHz
B1 ~B8
520/600/1000/1400/1500/1710 kHz/90.1/90.1 MHz
C1 ~C8
90.1 MHz
D1 ~D8
90.1 MHz
E1 ~E8
90.1 MHz
Surround modes and parameters
Signals and adjustability in the different modes
Channel output
Parameter (default values are shown in parentheses)
When playing Dolby
Digital and DTS signals
FRONT
L/R
CENTER
SURROUND
L/R
SUBWOOFER
EFFECT
L/R
TONE
CONTROL
CINEMA
EQ.
ROOM
SIZE
EFFECT
LEVEL
DELAY
TIME
D.COMP.
LFE
DIRECT
A
E
E
o
E
E
E
E
E
E
A (OFF)
A (0dB)
STEREO
A
E
E
o
E
A (0dB)
E
E
E
E
A (OFF)
A (0dB)
6CH/8CH EXTERNAL INPUT
A
o
o
o
A
A(0dB)
E
E
E
E
E
E
WIDE SCREEN
A
o
o
o
E
A (0dB)
A (OFF)
A (Medium)
A (10)
E
A (OFF)
A (0dB)
DOLBY PRO LOGIC
A
(THX CINEMA ON)
A
o
o
o
E
E
E
E
E
E
A (OFF)
A (0dB)
(THX CINEMA OFF)
A
o
o
o
E
A (0dB)
A (OFF)
E
E
E
A (OFF)
A (0dB)
(THX CINEMA ON)
A
o
o
o
E
E
E
E
E
E
A (OFF)
A (0dB)
(THX CINEMA OFF)
A
o
o
o
E
A (0dB)
A (OFF)
E
E
E
A(OFF)
A (0dB)
(THX CINEMA ON)
A
o
o
o
E
E
E
E
E
E
A (OFF)
A (0dB)
(THX CINEMA OFF)
A
o
o
o
E
A (0dB)
A (OFF)
E
E
E
A (OFF)
A (0dB)
5CH STEREO
A
o
o
o
E
A(0dB)
E
E
E
E
A (OFF)
A (0dB)
SUPER STADIUM
A
o
o
o
E
A(note 1)
E
A (Medium)
A (10)
E
A (OFF)
A (0dB)
ROCK ARENA
A
o
o
o
E
A(note 2)
E
A (Medium)
A (10)
E
A (OFF)
A (0dB)
JAZZ CLUB
A
o
o
o
E
A (0dB)
E
A (Medium)
A (10)
E
A (OFF)
A (0dB)
CLASSIC CONCERT
A
o
o
o
E
A (0dB)
E
A (Medium)
A (10)
E
A (OFF)
A (0dB)
MONO MOVIE
A
o
o
o
E
A (0dB)
E
A (Medium)
A (10)
E
A (OFF)
A (0dB)
MATRIX
A
o
o
o
E
A (0dB)
E
E
E
A (30msec)
A (OFF)
A (0dB)
Mode
DOLBY DIGITAL AC-3
DTS SURROUND
A : Signal/adjustable
C : Selected by speaker configuration setting
(Note 1) BASS: +6dB, TREBLE: 0dB
(Note 2) BASS: +8dB, TREBLE: +4dB
o:
E:
Turned on or off by speaker configuration setting
No signal/not adjustable
61
17 SPECIFICATIONS
2 Audio section
• Power amplifier
Rated output:
(All properties shown are only
for the power amplifier stage.)
Dynamic power:
Output terminals:
• Analog
Input sensitivity / input impedance:
Frequency response:
S/N:
Distortion:
Rated output/maximum output:
Maximum headphones output:
• Digital
D/A output:
Digital input:
• Phono equalizer (PHONO input — REC OUT)
Input sensitivity:
RIAA deviation:
Signal-to-noise ratio:
Rated output / Maximum output:
Distortion factor:
2 Video section
• Standard video jacks
Input / output level and impedance:
Frequency response:
• S-video jacks
Input / output level and impedance:
Frequency response:
• Color component video terminal
Input / output level and impedance:
Frequency response:
2 Tuner section
Receiving Range:
Usable Sensitivity:
50 dB Quieting Sensitivity:
Signal to Noise Ratio (IHF-A):
Total Harmonic Distortion (at 1 kHz):
Stereo (2ch driven)
140 W + 140 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.05% T.H.D.)
170 W + 170 W (8 Ω/ohms, 1 kHz with 0.7% T.H.D.)
Surround
140 W x 5 ch (8 Ω/ohms, 1 kHz with 0.7% T.H.D.)
190 W x 2 ch
310 W x 2 ch
390 W x 2 ch
Front/Center:
Surround:
(8 Ω/ohms)
(4 Ω/ohms)
(2 Ω/ohms)
16 ~ 16 Ω/ohms
A or B 16 ~ 16 Ω/ohms
A + B 12 ~ 16 Ω/ohms
200 mV / 47 kΩ/kohms
10 Hz ~ 100 kHz: +0, –3 dB (DIRECT mode)
105 dB (DIRECT mode)
0.005% (20 Hz ~ 20 kHz) (DIRECT mode)
1.2 V / 8 V
284 mW (8 Ω/ohms)
Rated output — 2 V (at 0 dB playback)
Total harmonic distortion — 0.005% (1 kHz, at 0 dB)
S/N ratio — 105 dB
Dynamic range — 96 dB
Format — Digital audio interface
2.5 mV
±1 dB (20 Hz to 20 kHz)
74 dB (A weighting, with 5 mV input)
150 mV / 8 V
0.03% (1 kHz, 3 V)
1 Vp-p, 75 Ω/ohms
5 Hz ~ 10 MHz — +0, –3 dB
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
C (color) signal — 0.286 Vp-p, 75 Ω/ohms
5 Hz ~ 10 MHz — +0, –3 dB
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
Cb (blue) signal — 0.7 Vp-p, 75 Ω/ohms
Cr (red) signal — 0.7Vp-p, 75 Ω/ohms
5 Hz ~ 20 MHz — +0, –3 dB
[FM] (note: µV at 75 Ω/ohms, 0 dBf = 1 x 10–15 W)
87.5 MHz ~ 107.9 MHz
1.0 µV (11.2 dBf)
MONO
1.6 µV (15.3 dBf)
STEREO 23 µV (38.5 dBf)
MONO
80 dB
STEREO 75 dB
MONO
0.15%
STEREO 0.3%
[AM]
520 kHz ~ 1710 kHz
18 µV
50 dB
2 General
Power supply:
Power consumption:
Maximum external dimensions:
Weight:
2 Remote control unit (RC-853)
Batteries:
External dimensions:
Weight:
AC 120 V, 60 Hz
11 A
434 (W) x 181 (H) x 494 (D) mm (17-3/32” x 7-1/8” x 19-29/64”)
21.5 kg (47 lbs 6 oz)
R6P/AA Type (two batteries)
70 (W) x 215 (H) x 24 (D) mm (2-3/4” x 8-15/32” x 15/16”)
200 g (Approx. 7 oz) (including batteries)
* For purposes of improvement, specifications and design are subject to change without notice.
62
14-14, AKASAKA 4-CHOME, MINATO-KU, TOKYO 107-8011, JAPAN
Telephone: (03) 3584-8111
Cable: NIPPON COLUMBIA TOKYO Telex: JAPANOLA J22591
Printed in Japan. 511 3418 005
901
Download PDF
Similar pages
Sharp Htsb600 Quick Specs
P42W22B_New Style.qxd
The Samsung HW-C700 home theater receiver is for those who
AVC-A1HD
AVR-1602
ADV-700
AVR-3802
AVR-1403 - One Call
For sale
D2v Data Sheet